Search results for "Oven Thermostats"

XPARTCO 279973 Dryer Thermostat Kit The XPARTCO 279973 is an aftermarket replacement dryer thermostat and thermal cut-off kit compatible with a wide range of Whirlpool-family electric dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Roper, and Admiral. The kit contains two components — the high-limit thermostat (L295-80F) and the thermal cut-off fuse — both located on the heating element housing. Together they protect the dryer's heating element from overheating: the high-limit thermostat monitors element temperature and cuts power if it exceeds safe levels, then resets when cooled. The thermal cut-off fuse is a backup one-time device that permanently opens the circuit if the thermostat fails to protect the element. Both parts are mounted on the side of the heating element housing and can be accessed through the dryer's back panel. The thermal cut-off fuse is a non-resettable one-time device — once it opens, it must be replaced. The 279973 kit includes both parts, an instruction sheet, and hardware. It directly replaces 3391913, 3404151, 3404152, 3977395, 8318314, 897710, 279973VP, AP3094323, and several additional cross-reference numbers. Note: this kit is for electric dryers only. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO 279973 Dryer Thermostat Kit fixes Whirlpool-family electric dryers with no heat, overheating, or a dryer that shuts off too early. Kit includes the L295-80F high-limit thermostat (auto-reset, opens at 295°F) and the thermal cut-off fuse (352°F, one-time). Both mount on the heating element housing. Electric dryers only. Replaces 3391913, 3404151, 8318314, 897710, AP3094323. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Roper, and Admiral. Common Problems This Kit Fixes Dryer produces no heat — thermal cut-off fuse or high-limit thermostat has failed Dryer overheats — clothes or drum too hot at the end of a cycle Dryer shuts off early before clothes are dry Dryer takes multiple cycles or very long time to dry clothes Repeated no-heat failures — underlying overheating condition affecting the element housing components Dryer tumbles normally but produces no heat at all What's in the Kit Part 1 of 2 High-Limit Thermostat (L295-80F) Opens at 295°F — cuts power to the heating element if temperature exceeds safe levels · Auto-resets when cooled · Located on the heating element housing · Should show closed continuity (near-zero resistance) at room temperature Part 2 of 2 Thermal Cut-Off Fuse (352°F) Opens at 352°F — one-time backup safety device on the heating element housing · Permanently interrupts power to the heating element if the high-limit thermostat fails to protect it · Cannot be reset — must be replaced if blown · Should show closed continuity at room temperature when working Replaces Part Numbers This thermostat kit directly replaces the following OEM and cross-reference part numbers: 279973, 279973VP, 3391913, 3404151, 3404152, 3977395, 8318314, 897710, ER279973, PD00002626, EAP334387, AWP39286, AH334387, AP3094323, EA334387, PS334387. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat kit is compatible with select electric dryers only from the following brands: Whirlpool electric dryers (Duet, Cabrio, and standard series) Kenmore / Sears electric dryers (Whirlpool-built models) Maytag electric dryers KitchenAid electric dryers Amana electric dryers Inglis electric dryers Roper electric dryers Admiral electric dryers Important: This kit is for electric dryers only. Gas dryers use a different burner assembly and require a different thermostat kit (XP6974 for Whirlpool-family gas dryers). Always verify your dryer type and model number before ordering. Also: if the thermal cut-off fuse has blown, always check for a clogged exhaust vent before replacing — a blocked vent is the most common root cause of overheating and repeated fuse failures. Key Features 2-part kit — high-limit thermostat and thermal cut-off fuse, both on the heating element housing High-limit thermostat (L295-80F) — opens at 295°F to cut element power, auto-resets when cooled Thermal cut-off fuse (352°F) — one-time backup safety device; permanently opens if thermostat fails to protect the element Both parts located on the heating element housing — accessible from the dryer back panel Replacing both together ensures complete thermal protection is restored on the element housing Replaces 3391913, 3404151, 8318314, 897710, AP3094323, and over 10 additional cross-reference numbers Electric dryers only — not for gas dryer models Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Roper, and Admiral electric dryers Aftermarket replacement built to OEM-equivalent quality standards Installs in 20–30 minutes with basic hand tools Product Specifications Kit Part Number 279973 Condition Aftermarket Replacement Application Electric Dryers Only Kit Includes 1x High-Limit Thermostat (L295-80F), 1x Thermal Cut-Off Fuse (352°F), hardware, instruction sheet High-Limit Thermostat Rating L295-80F — opens at 295°F, resets at 215°F — auto-resets Thermal Cut-Off Fuse Trip Temp 352°F — one-time, non-resettable Location Heating element housing (both parts) Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Roper, Admiral Installation Notes ⚠️ Unplug Dryer Before Starting — Electric Dryers Only Disconnect power before beginning. Remove the back panel of the dryer by unscrewing the perimeter screws to expose the heating element housing. Both the high-limit thermostat and thermal cut-off fuse are mounted on the side of the heating element housing — the thermostat is typically the larger component and the thermal cut-off fuse is smaller. Test each component with a multimeter before removing (both should show closed continuity at room temperature; the failed one will read open). Photograph the wiring before disconnecting. Disconnect the wires, remove the mounting screws, and install the new components in the same positions. Reconnect the wires and mounting screws, reinstall the back panel, restore power, and run a test cycle to confirm heat. Tip: Before running the dryer, clean the full length of the exhaust duct — a clogged vent is the most common cause of overheating and a blown thermal cut-off fuse. Tools needed: Phillips screwdriver, 1/4" nut driver, multimeter. Frequently Asked Questions What is the difference between the high-limit thermostat and the thermal cut-off fuse in this kit? The high-limit thermostat (L295-80F) is a resettable safety switch that opens at 295°F to cut power to the heating element and resets automatically when the temperature drops. It is the primary protection against overheating during normal operation. The thermal cut-off fuse is a one-time backup device rated at 352°F — it permanently opens the circuit if the heating element temperature climbs beyond the point the thermostat should have caught. Once the cut-off fuse opens, it must be replaced; it does not reset on its own. If the cut-off fuse has blown, it usually means the high-limit thermostat also failed to do its job and should be replaced at the same time — which is exactly what this kit provides. How do I test these parts with a multimeter? Unplug the dryer and remove the back panel to access the heating element housing. Disconnect each component from the wiring and probe both terminals with a multimeter set to continuity or resistance mode. At room temperature, both the high-limit thermostat and the thermal cut-off fuse should show closed continuity (near-zero resistance). Any component that reads open circuit (no continuity) has failed and needs to be replaced. The thermal cut-off fuse reads open even after it cools — it is non-resettable. The high-limit thermostat may read open at room temperature if it has failed internally rather than by an overheat trip. How is the 279973 kit different from the XP6974 thermostat kit? The 279973 is a 2-part kit — high-limit thermostat and thermal cut-off fuse — designed specifically for the heating element housing of Whirlpool-family electric dryers. The XP6974 is a 4-part kit — cycling thermostat, thermal fuse, high-limit thermostat, and thermal cut-off — designed for Whirlpool-family gas and electric dryers, covering both the exhaust duct components and the burner/element housing components. If your electric dryer is showing no-heat and you need only the heating element housing components, the 279973 kit covers exactly those two parts. If you want to replace all thermal components in one repair, the XP6974 covers a broader set. Why does the thermal cut-off fuse keep blowing? If the thermal cut-off fuse blows repeatedly after replacement, it almost always means there is an underlying overheating condition causing the heating element housing to run hotter than it should. The most common cause is a clogged or restricted exhaust vent — lint accumulation in the duct reduces airflow, trapping heat inside the dryer cabinet and around the element. Other causes include a failed cycling thermostat that is not regulating element temperature correctly, a stuck heating element relay, or a dryer in an enclosed space with inadequate ventilation. Always clean the full exhaust duct and check the cycling thermostat (WP3387134) before replacing the thermal cut-off fuse a second time. Is this an OEM or aftermarket part? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the temperature ratings and specifications of the original 279973 high-limit thermostat and thermal cut-off fuse kit. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO XP6974 Dryer Thermostat Kit Replaces WP3387134, WP3392519, W10900067, 279816 The XPARTCO XP6974 is an aftermarket dryer thermostat kit containing four thermal components for Whirlpool-family electric and gas dryers including Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef. The kit includes the cycling thermostat (WP3387134), thermal fuse (WP3392519), high-limit thermostat and thermal cut-off kit (279816 / W10900067) — the complete set of heat-sensing and safety components that regulate dryer temperature and prevent dangerous overheating. These four components work together to control and protect the dryer's heating system. When any one of them fails, the dryer may produce no heat, overheat, run too long, or stop mid-cycle. Because a failed thermal fuse is almost always caused by an underlying overheating condition that also stresses the other components, replacing all four together in a single repair is the recommended approach. Includes all wiring hardware needed for installation. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO XP6974 Dryer Thermostat Kit fixes Whirlpool-family dryers that produce no heat, overheat, take too long to dry, or stop mid-cycle. Includes all four thermal components: cycling thermostat (L155-25), thermal fuse (196°F), high-limit thermostat (L250-80), and thermal cut-off (309°F). Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef electric and gas dryers. Common Problems This Kit Fixes Dryer produces no heat — thermal fuse or high-limit thermostat has blown Dryer takes multiple cycles or very long time to dry clothes Dryer overheats — clothes or drum too hot to touch after a cycle Dryer shuts off mid-cycle and will not restart Dryer tumbles normally but generates no heat at all Dryer runs too long because cycling thermostat is not regulating temperature Repeated thermal fuse failures — underlying thermostat fault causing recurring overheating What's in the Kit Part 1 of 4 WP3387134 Cycling Thermostat Rated L155-25 · Monitors drum air temperature and cycles the heating element on and off to maintain the set drying temperature · Located on the exhaust duct or blower housing · Should show closed continuity at room temperature Part 2 of 4 WP3392519 Thermal Fuse Opens at 196°F (91°C) · One-time safety device located on the exhaust duct · Permanently interrupts power to the heating element if the dryer overheats · Cannot be reset — must be replaced if blown · Most common cause of no-heat in Whirlpool-family dryers Part 3 of 4 High-Limit Thermostat (279816 / W10900067) Rated L250-80 · Mounted on the heating element housing · Opens at approximately 250°F to cut power to the heating element if temperature exceeds safe limits · Resets automatically when it cools · Should show closed continuity at room temperature Part 4 of 4 Thermal Cut-Off Fuse (3977393 / 279816 kit) Opens at 309°F · Backup one-time safety device on the heating element housing · Permanently interrupts power to the heating element if the high-limit thermostat fails to open · Cannot be reset — must be replaced if blown Replaces Part Numbers WP3387134 Cycling Thermostat cross-references: WP3387134, WP3387134VP, 3387134, 3387135, 3387139, 306910, 3-6910, ET187, AP6008270, PS11741405 WP3392519 Thermal Fuse cross-references: WP3392519, WP3392519VP, 3392519, 3388651, 694511, 80005, ET401, G4AP0500, AP6008325, PS11741460 279816 High-Limit Thermostat and Thermal Cut-Off Kit cross-references: 279816, 279816VP, W10900067, 3977393, 3977767, WP3977767, WP3977767VP, 3399848, 3399693, 2651, AP3094244, AH334299, EA334299, EAP334299, PS334299 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat kit is compatible with select gas and electric dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (Whirlpool-built models) Maytag dryers (gas and electric) Amana dryers KitchenAid dryers Roper dryers Admiral dryers Estate dryers Crosley dryers Inglis dryers Magic Chef dryers Important: If your thermal fuse has blown, always check for the root cause before replacing — a clogged exhaust vent is the most common cause of dryer overheating. Clean the full length of the exhaust duct before or after this repair. If the vent is clear, a failed cycling thermostat or high-limit thermostat is likely the root cause. Key Features Complete 4-part thermal kit — covers the cycling thermostat, thermal fuse, high-limit thermostat, and thermal cut-off in a single repair Cycling thermostat (L155-25) — regulates drum temperature to maintain consistent, efficient drying Thermal fuse (196°F) — one-time safety device that permanently interrupts heat if the dryer overheats High-limit thermostat (L250-80, ~250°F) — cuts power to the heating element when temperature exceeds safe limits; auto-resets Thermal cut-off (309°F) — backup one-time safety device protecting against heating element runaway Replacing all four parts together ensures the complete thermal circuit is renewed — prevents recurrence if a failing thermostat caused the fuse to blow Includes all wiring hardware for installation Compatible with 11 major appliance brands on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Kit Part Number XP6974 Condition Aftermarket Replacement Application Gas and Electric Dryers Kit Includes 1x WP3387134 Cycling Thermostat, 1x WP3392519 Thermal Fuse, 1x High-Limit Thermostat (L250-80), 1x Thermal Cut-Off Fuse (309°F), wiring hardware Cycling Thermostat Rating L155-25 (closes at 155°F, opens at 25°F differential) Thermal Fuse Trip Temp 196°F (91°C) — one-time, non-resettable High-Limit Thermostat Rating L250-80 (opens at ~250°F) — auto-resets Thermal Cut-Off Trip Temp 309°F — one-time, non-resettable Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef Installation Notes ⚠️ Unplug Dryer and Shut Off Gas Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the back panel of the dryer to access the heating element housing and exhaust duct. The thermal fuse (WP3392519) and cycling thermostat (WP3387134) are located on the exhaust duct or blower housing — disconnect the wires, unscrew the mounting screws, and install the new parts in the same positions. The high-limit thermostat and thermal cut-off (279816 kit) are located on the heating element housing — disconnect the wires and unscrew the mounting screws to remove the old parts and install the new ones. Reconnect all wires to the correct terminals — take a photo before disconnecting to reference during reinstallation. Reassemble the back panel, restore power, and run a test cycle to verify heat. Tip: Before running the dryer, also clean the full length of the exhaust duct — a clogged vent is the most common root cause of dryer overheating and repeated thermal fuse failures. Tools needed: Phillips screwdriver, 1/4" nut driver, needle-nose pliers. Frequently Asked Questions What does each part in this kit do? The cycling thermostat (WP3387134) monitors the air temperature in the exhaust duct and cycles the heating element on and off to maintain the correct drying temperature — it is the part that controls how hot the dryer gets during normal operation. The thermal fuse (WP3392519) is a one-time safety device that permanently cuts power to the heating element if the dryer overheats above 196°F — it is the most common cause of no-heat in Whirlpool-family dryers. The high-limit thermostat opens at approximately 250°F to cut heating element power if temperature gets too high, and resets automatically when it cools. The thermal cut-off is a backup one-time fuse on the heating element that opens at 309°F if the high-limit thermostat fails to protect the heater. Why should I replace all four parts instead of just the one that failed? When a thermal fuse blows, it almost always blew because the dryer overheated — and that overheating event put significant stress on all the other thermal components as well. A failing cycling thermostat is the most common cause of repeated thermal fuse failures: if the cycling thermostat stops regulating temperature correctly, the dryer runs too hot, the high-limit thermostat is repeatedly stressed, and the thermal fuse eventually blows. Replacing just the fuse without replacing the cycling thermostat means the same overheating will blow the new fuse. Replacing all four parts at once eliminates that risk in a single repair. How do I test these parts with a multimeter? Set the multimeter to continuity or resistance mode. The thermal fuse (WP3392519), cycling thermostat (WP3387134), and high-limit thermostat should all show closed continuity (near-zero resistance) at room temperature. The thermal cut-off should also show closed continuity at room temperature. Any part that reads open (no continuity / infinite resistance) at room temperature has failed and needs to be replaced. A blown thermal fuse or cut-off will always read open — they are one-time devices and cannot reset. What causes the thermal fuse to blow repeatedly? The most common cause by far is a clogged exhaust vent — lint accumulation inside the dryer duct restricts airflow, causing heat to build up inside the dryer cabinet until the thermal fuse trips. Always clean the full length of the exhaust duct before and after replacing these parts. Other causes include a failing cycling thermostat that is not regulating temperature correctly, a stuck heating element relay, or a dryer placed in an enclosed space without adequate ventilation. Is this kit compatible with both electric and gas dryers? Yes — the XP6974 kit is compatible with both electric and gas Whirlpool-family dryers. Both types use the same cycling thermostat (WP3387134) and thermal fuse (WP3392519). The high-limit thermostat and thermal cut-off (279816 kit) are located on the heating element in electric models and on the burner assembly area in gas models. Always verify your specific model number before ordering to confirm all four parts apply to your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 279816 Dryer Thermostat Kit The XPARTCO 279816 is an aftermarket replacement thermal fuse and high-limit thermostat combo kit for Whirlpool-built dryers. These are the dryer's two thermal safety devices, and they're bundled together in this kit because they tend to fail around the same time and share a common cause: restricted airflow that lets heat build up beyond safe levels. The high-limit thermostat is the first line of defense, opening at approximately 250°F (L250-80F) to interrupt heating if the dryer runs too hot. If that isn't enough to bring the temperature back down, the thermal fuse is the final failsafe, opening permanently at approximately 309°F to cut power to the dryer entirely. That's an important distinction between the two parts: the high-limit thermostat is a cycling safety device that can open and close as temperature rises and falls, while the thermal fuse is a one-time device — once it blows, it's done, and the dryer won't run again until it's replaced. This kit includes both components plus mounting screws and a wiring set with a jumper wire and extra terminals, which is used specifically when replacing an older-style thermostat that had a wire pressing directly onto the heating element. A dryer that won't start at all, with no lights or response, usually means the thermal fuse has blown; a dryer that runs but won't heat, or that stops heating partway through a cycle, points more toward the thermostat. It directly replaces 2651, 279816VP, 3399848, 3977393, 3390291, AP3094244, AH334299, EA334299, EAP334299, PD00002348, and PS334299. Quick Answer The XPARTCO 279816 Dryer Thermostat Kit fixes Whirlpool-built dryers that won't start at all, won't heat, or stop heating partway through a cycle. Includes a thermal fuse (opens ~309°F), a high-limit thermostat (opens ~250°F), mounting screws, and a wiring set. Replaces 2651, 279816VP, 3399848, 3977393, 3390291, AP3094244, AH334299, EA334299, EAP334299, PD00002348, PS334299. Always inspect and clean the dryer venting when replacing this kit — a blown fuse or tripped thermostat is a symptom of restricted airflow, and skipping this step means the new parts are likely to fail again. Common Problems This Part Fixes Dryer won't start at all — no lights, no tumble, no response to any button Dryer runs and tumbles but produces no heat Dryer heats for a while, then stops heating partway through a cycle Dryer that stopped working suddenly, especially after running unusually hot Clothes coming out extremely hot right before the dryer stopped heating or stopped entirely Repeated blown fuses or tripped thermostats on a dryer with a known venting restriction Continuity test shows an open circuit across the old fuse or thermostat Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermostat kit directly replaces the following OEM and cross-reference part numbers: 279816, 279816VP, 3399848, 3977393, PD00002348, AWP39198, EAP334299, AH334299, EA334299, AP3094244, PS334299. 3977393 is the thermal fuse component and 3390291 is the "new-style" high-limit thermostat component included in this kit. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat kit is compatible with select Whirlpool-built dryers across the Whirlpool family of brands, including: Whirlpool electric and gas dryers — WED series Maytag electric and gas dryers — NED series (select Whirlpool-built models) Admiral, Amana, Crosley, Estate, Inglis, Magic Chef, and Roper dryers (select models) Kenmore and KitchenAid dryers (select Whirlpool-built models) Verified model numbers include: WED6200SW1, NED4600YQ0, NED4600YQ1, NED4655EW1, and LER3624EQ. Note: The wiring set included in this kit is designed for replacing an older-style thermostat that used a wire pressed directly onto the heating element. If your dryer uses the true old-style push-on thermostat and fuse combination (part 3977767), you'll need a different kit (commonly listed as APN197) instead of this one. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which kit fits your dryer. Key Features Complete combo kit — thermal fuse, high-limit thermostat, mounting screws, and wiring set in one package Thermal fuse opens at approximately 309°F as a one-time, non-resettable safety cutoff High-limit thermostat opens at approximately 250°F (L250-80F) as a cycling safety device Resolves "won't start at all," "runs but doesn't heat," and "stops heating mid-cycle" symptoms Wiring set includes jumper wire and extra terminals for older-style push-on thermostat connections Replaces 2651, 279816VP, 3399848, 3977393, 3390291, AP3094244, AH334299, EA334299, EAP334299, PD00002348, and PS334299 Compatible with Whirlpool, Maytag, Admiral, Amana, Crosley, Estate, Inglis, Magic Chef, Roper, Kenmore, and KitchenAid dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 279816 OEM Part Number 279816 Part Type Dryer Thermal Fuse & High-Limit Thermostat Kit Condition Aftermarket Replacement Kit Contents Thermal fuse, high-limit thermostat, mounting screws, wiring set Thermal Fuse Opening Temp Approx. 309°F (one-time, non-resettable) High-Limit Thermostat Opening Temp Approx. 250°F / L250-80F (cycling) Wiring Set Jumper wire + extra terminals for older-style push-on thermostats Quantity 1 kit Compatible Brands Whirlpool, Maytag, Admiral, Amana, Crosley, Estate, Inglis, Magic Chef, Roper, Kenmore, KitchenAid Installation Notes ⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel: remove the screws securing the panel to reach the blower housing area where both the thermal fuse and high-limit thermostat are mounted, usually close together near the heating element or blower assembly. Photograph the wiring before disconnecting anything, and note whether your old thermostat used a push-on wire connection at the heating element — if so, use the included jumper wire and extra terminals to make the new connection correctly. Remove the mounting screws holding each old component in place and disconnect their wire terminals. Before installing the new parts, test the old fuse and thermostat with a multimeter to confirm which one (or both) is actually open, rather than assuming. This is the most important step: fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. A blown fuse or tripped thermostat is a symptom of restricted airflow, and skipping this step means the new parts are likely to fail again. Install the new thermal fuse and thermostat from this kit in the same mounting positions, reconnect the wire terminals (using the included wiring set if applicable), and secure the mounting screws. Reinstall the rear panel, restore power, and run a test cycle to confirm normal heating and shutoff behavior. Tools needed: Phillips or nut driver (model-dependent), multimeter, vent brush or vacuum attachment for cleaning ductwork, work gloves. Frequently Asked Questions Why does this kit include two different parts instead of just one? The thermal fuse and high-limit thermostat work together as a two-stage safety system, and they're bundled because they commonly fail together — both are reacting to the same underlying overheating condition, usually restricted airflow. The high-limit thermostat trips first at a lower temperature and can cycle open and closed; if that's not enough to control the heat, the thermal fuse trips at a higher temperature and shuts the dryer down permanently until replaced. Replacing both together addresses the full safety chain rather than just one link in it. My dryer won't start at all versus my dryer runs but doesn't heat — which part is which? A dryer with absolutely no response — no lights, no tumbling, nothing — usually points to the thermal fuse, since it's wired to cut power more broadly when it blows. A dryer that tumbles and runs normally but produces no heat, or that starts heating and then stops partway through, points more toward the high-limit thermostat. Testing both components with a multimeter will confirm exactly which one has failed. I replaced both parts and the dryer failed again. What's going on? This is a strong sign that the underlying cause — almost always restricted airflow — was never addressed. Neither of these parts fails from age; they trip or blow because the dryer overheated. If new parts fail again, thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. If airflow checks out and the parts still fail, have the heating element checked as well, since a shorted element can also drive excess heat. Do I need the wiring set included in this kit? Only if your dryer's original thermostat used a wire that pressed directly onto the heating element (an older-style connection) rather than a standard push-on terminal. If your dryer already uses a straightforward terminal connection, you can skip the jumper wire and extra terminals and connect the new thermostat directly. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the opening temperatures, terminal configuration, and mounting positions of the original 279816 thermal fuse and high-limit thermostat kit used in compatible Whirlpool, Maytag, and related dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

316233903 Oven Genuine Temperature Sensor Replaces Part Numbers:  316233903, 316217008, 316233902, 316233900, AP5998652, PS11731754. Description: This Oven Temperature Sensor is a Genuine part for select Frigidaire, Kenmore oven models. It monitors and regulates the oven's temperature by sending accurate temperature readings to the control board. This ensures that the oven maintains the desired cooking temperature throughout the baking or roasting process.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO XP8767 Dryer Thermostat Set — DC47-00018A, DC96-00887C, DC47-00016A, DC32-00007A The XPARTCO XP8767 is an aftermarket dryer thermal component set containing four heat-sensing and safety parts for select Samsung and Kenmore dryers. The set includes the high-limit thermostat (DC47-00018A), thermal fuse with bracket (DC96-00887C), blower housing thermal fuse (DC47-00016A), and thermistor temperature sensor (DC32-00007A) — the complete set of thermal components that regulate temperature and prevent overheating in compatible Samsung dryers. When any one of these components fails, the dryer may produce no heat, run too hot, shut off too early, or fail to start. Because overheating events that blow a thermal fuse also stress the other thermal components, replacing all four together in a single repair is the recommended approach. The DC96-00887C replaces the DC96-00887A used in earlier models — both are included in this kit's cross-references. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO XP8767 Dryer Thermostat Set fixes Samsung and Kenmore dryers with no heat, insufficient heat, overheating, early shutoff, or failure to start. Includes all four thermal components: DC47-00018A high-limit thermostat (L260-50), DC96-00887C thermal fuse with bracket (320°F), DC47-00016A blower housing thermal fuse, and DC32-00007A thermistor. Compatible with Samsung and Kenmore (Samsung-built) dryers. Common Problems This Set Fixes Dryer produces no heat — thermal fuse or high-limit thermostat has failed Dryer produces insufficient heat — thermistor not regulating temperature correctly Dryer shuts off too early before clothes are dry Dryer will not start at all Dryer overheats — drum or clothes too hot at end of cycle Dryer cycle runs but timer does not advance Clothes not drying properly despite the dryer running normally What's in the Set Part 1 of 4 DC47-00018A High-Limit Thermostat Rated L260-50 · Opens at 260°F (127°C), resets at 210°F (99°C) · Mounted on the heating element housing · Cuts power to the heating element if drum temperature exceeds safe limits · Auto-resets when cooled · Should show closed continuity at room temperature Part 2 of 4 DC96-00887C Thermal Fuse with Bracket Opens at 320°F (160°C) · One-time safety device mounted on the exhaust duct with bracket · Permanently cuts power to heat source if dryer overheats · Cannot be reset — must be replaced if blown · Replaces DC96-00887A used in earlier models Part 3 of 4 DC47-00016A Thermal Fuse (Blower Housing) Located on the blower housing · One-time safety device that cuts power to the motor if the dryer overheats · Cannot be reset — must be replaced if blown · Should show closed continuity at room temperature when working Part 4 of 4 DC32-00007A Thermistor Temperature Sensor Attached to the blower housing · Varies in resistance during the drying cycle to monitor and regulate drum temperature in real time · Communicates temperature readings to the control board · A failed thermistor causes incorrect drying temperatures, premature shutoff, or erratic cycle behavior Replaces Part Numbers DC47-00018A Dryer Hi Limit Thermostat Dryer high-limit thermostat, L260-50F. Replaces Parts Numbers: DC47-00018A, AP4201898, EAP2430930, PS2430930, ASM33627, PD00002011, 35001092, WP35001092, ASM33627, PD00004704, EAP11741822, AP6008682, PS11741822. DC96-00887C  Dryer Thermal Cut Off The fuse is not re-settable and will need to be replaced if blown. If the dryer does not heat, the thermal fuse may be blown. Replaces Part Numbers: DC96-00887C, DC96-00887A, ASM65115, PD00035400, AP4207819, EAP4216838, PS4216838, 2074129, WP35001193, 35001193, EAP11741829, AP6008689, PS11741829, AWP47381, PD00003365. DC47-00016A Dryer Thermostat Replaces Part Number: DC47-00016A, 2068545, ASM868996, PD00003747, AP4201894, PS4205213, WP35001087, 35001087, AWP47334, PD00003747, AP6008681, PS11741821. DC32-00007A Dryer Thermistor: Dryers Replacement Thermistor Replaces Part Numbers: DC32-00007A, ASM654843, PD00001996, 2068429, AP4201716, PS4204984, WP35001191, 35001191, 1185513, AH2038482, PD00003059, EAP11741828, AP6008688, PS11741828. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat set is compatible with select dryers from the following brands: Samsung dryers (gas and electric — DV, DVE, DVG series) Kenmore / Sears dryers (select Samsung-built models) Important: If a thermal fuse has blown, always check for the root cause before replacing — a clogged exhaust vent is the most common cause of dryer overheating. Clean the full length of the exhaust duct before running the dryer after this repair. Key Features Complete 4-part thermal set — covers all Samsung dryer thermal components in a single repair DC47-00018A high-limit thermostat (L260-50) — auto-resets; cuts heating element power at 260°F DC96-00887C thermal fuse with bracket (320°F) — one-time safety device; replaces DC96-00887A used in earlier models DC47-00016A thermal fuse on blower housing — one-time safety device that protects the motor DC32-00007A thermistor — monitors real-time drum temperature and communicates with the control board to regulate drying cycles Replacing all four parts together renews the complete thermal circuit — prevents recurrence if a failing component caused the fuse to blow Compatible with Samsung DV, DVE, and DVG series dryers and Samsung-built Kenmore models Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Set Part Number XP8767 Condition Aftermarket Replacement Application Samsung and Kenmore Gas and Electric Dryers Set Includes 1x DC47-00018A High-Limit Thermostat, 1x DC96-00887C Thermal Fuse with Bracket, 1x DC47-00016A Thermal Fuse, 1x DC32-00007A Thermistor DC47-00018A Rating L260-50 — opens at 260°F (127°C), resets at 210°F (99°C) — auto-resets DC96-00887C Trip Temp 320°F (160°C) — one-time, non-resettable DC47-00016A One-time thermal fuse on blower housing — non-resettable DC32-00007A Thermistor — resistance varies with temperature; communicates with control board Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Dryer and Shut Off Gas Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the back panel of the dryer to access the heating element housing and exhaust duct. Take a photo of all wire connections before disconnecting anything — the thermistor and thermal fuses use similar small connectors and it is important to reconnect them to the correct terminals. The DC47-00018A high-limit thermostat is mounted on the heating element housing — unscrew and replace it. The DC96-00887C thermal fuse with bracket is mounted on the exhaust duct — unscrew, remove the bracket assembly, and install the new one. The DC47-00016A thermal fuse is on the blower housing — disconnect the wires and unscrew or unclip it. The DC32-00007A thermistor is clipped to the blower housing — pull the old one out and press the new one into the clip. Reconnect all wires, reassemble the back panel, restore power, and run a test cycle. Tip: Clean the full length of the exhaust duct before running the dryer after this repair. Tools needed: Phillips screwdriver, 1/4" nut driver, needle-nose pliers. Frequently Asked Questions What does each part in this set do? The DC47-00018A high-limit thermostat monitors the heating element temperature and cuts power to the element at 260°F if the dryer gets too hot — it resets automatically when cooled. The DC96-00887C thermal fuse is a one-time safety device on the exhaust duct that permanently cuts power to the heat source at 320°F if the dryer overheats. The DC47-00016A is a second one-time thermal fuse on the blower housing that cuts power to the motor if overheating occurs there. The DC32-00007A thermistor monitors real-time drum temperature and sends resistance-based readings to the control board, which uses them to regulate the drying cycle and control the heating element. What is the difference between DC96-00887A and DC96-00887C? The DC96-00887C is the updated current part number that superseded the DC96-00887A. Both are the same thermal fuse with bracket used on the exhaust duct — the C suffix denotes a minor revision. Either part number is covered by this kit and both are fully interchangeable. How do I test these parts with a multimeter? Set the multimeter to continuity or resistance mode. At room temperature, the DC47-00018A high-limit thermostat and both thermal fuses (DC96-00887C and DC47-00016A) should all show closed continuity (near-zero resistance). Any of these that reads open (no continuity) has failed. The DC32-00007A thermistor should show a resistance reading at room temperature — typically around 10,000–50,000 ohms depending on ambient temperature — rather than zero or open. A thermistor that reads open or zero at room temperature has failed. Why should I replace all four parts instead of just the one that failed? When a thermal fuse blows in a Samsung dryer, it almost always means the dryer overheated — and that overheating event stresses all four thermal components simultaneously. Replacing just the blown fuse without replacing the other parts risks a repeat failure if the thermistor is providing incorrect readings or the high-limit thermostat is no longer protecting accurately. Replacing all four parts at once renews the entire thermal circuit and reduces the chance of a repeat failure in the near future. Is this set for electric and gas Samsung dryers? Yes — the XP8767 set is compatible with both electric (DVE series) and gas (DVG series) Samsung dryers that use these four thermal components. Always verify your specific model number before ordering to confirm all four parts apply to your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

DE47-20059B Microwave Genuine Thermostat Fits specific Samsung microwave models. Replaces Part Numbers: DE47-20059B, 2079767, DE47-20059A, OEM18320450, AP4580112, PS4226453.Description: This Microwave Thermostat is an essential component for maintaining the optimal performance of your Samsung microwave. This genuine OEM part ensures precise temperature control, helping your appliance operate safely and efficiently. Designed specifically for Samsung microwave models, the thermostat guarantees a perfect fit and seamless integration with your existing system. By replacing a faulty or damaged thermostat with this high-quality part, you can restore your microwave's functionality and extend its lifespan. The Microwave Thermostat is built to withstand the demands of everyday use, providing reliable performance and consistent heating results. Easy to install, this thermostat allows you to perform repairs yourself, saving you time and the cost of professional service. Enhance your microwave reliability and enjoy peace of mind knowing you are using a genuine OEM part that delivers both quality and durability.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

DG32-00002B Range Oven Genuine Temperature Sensor Replaces Part Numbers: DG32-00002B, 2087461, DG32-00002A, AP4343210, PS4240743. Description: This Range Oven Temperature Sensor ensures precise temperature control for your cooking needs. This genuine OEM part is designed specifically for Samsung ranges, guaranteeing a perfect fit and reliable performance. By accurately monitoring oven temperatures, it helps maintain consistent cooking results, preventing under-cooked or burnt meals. Installing this sensor is straightforward, allowing you to restore your oven's functionality without hassle. Its durable construction ensures long-lasting use, providing peace of mind and enhancing your appliance's efficiency. Whether you're baking, roasting, or broiling, the Range Oven Temperature Sensor delivers the accuracy you expect from a high-quality component.

Read more less

W10169881 Dryer Genuine OEM Thermostat Kit Description: This Dryer thermostat kit is an OEM replacement part responsible for ensuring the safety and temperature regulation of the dryer. The high-limit thermostat serves as a critical safety device that monitors and regulates the temperature inside the dryer. When the temperature rises to a level beyond the safe operating range, the high-limit thermostat interrupts the flow of electricity to the heating element. The thermal cut-out fuse, included in this kit, offers an additional layer of protection by disconnecting power to the heating element if it detects excessively high temperatures. Replaces Part Numbers: W10169881, 1455409, AH1964653, EA1964653, AP4316800, PS1964653.    California Residents only WARNING: California’s Proposition 65

Read more less

ERP WE4M181 Dryer Cycling Thermostat This cycling thermostat is a replacement part responsible for regulating and controlling the temperature inside a dryer during the drying cycle. Typically located near the dryer's heating element or burner assembly, this thermostat constantly monitors the temperature within the dryer drum. Its primary function is to cycle the heating element on and off as needed to maintain a consistent and safe operating temperature.  The cycling thermostat can also be used on Specific Hotpoint, RCA, and Kenmore/Sears appliance models. Replaces Part Numbers: WE4M181, WE04M0181, WE4M245, AH267926, EA267926, AP2044414, PS267926.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: California’s Proposition 65 

Read more less

279973 Dryer Genuine OEM Thermostat Kit Replaces: 279973, 279973VP, 3391913, 3404151, 3404152, 3977395, 8318314, 897710, ER279973, AH334387, AP3094323, EA334387, PS334387.  Description: This Thermal Cut-Off Kit is a Genuine OEM part for select Kenmore, Whirlpool dryer models, responsible for protecting the dryer from overheating by interrupting the power flow to the heating element if the dryer air temperature reaches a dangerously high level.  

Read more less

XPARTCO 280148 Dryer Thermostat Set The XPARTCO 280148 is an aftermarket replacement thermal fuse and high-limit thermostat set for Whirlpool electric dryers, and also fits select Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, KitchenAid, and Norge models. This set bundles the 8557403 high-limit thermostat, which monitors temperature and automatically cuts power to the heating element if it overheats, then resets itself once the dryer cools, together with the 8318314 thermal fuse, a one-time backup safety device that permanently opens the circuit if temperatures climb high enough that the thermostat alone doesn't prevent an overheat. These two parts are sold together and commonly fail around the same time, since they protect the same circuit and respond to the same underlying overheating conditions — most often restricted exhaust venting. Symptoms include the dryer not heating at all, taking longer than normal to dry a load, or overheating before shutting down. It directly replaces 280148VP, 1175772, AP3874047, PS991443, EAP991443, and 314634. Quick Answer The XPARTCO 280148 Dryer Thermostat Set fixes Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, KitchenAid, and Norge electric dryers with no heat, drying that takes too long, or a dryer that overheats before shutting down. Includes the 8557403 high-limit thermostat (auto-resetting) and 8318314 thermal fuse (one-time). Replaces 280148VP, 1175772, AP3874047, PS991443, EAP991443, 314634. Always inspect and clean the exhaust venting when replacing this set — a blown thermal fuse is a symptom of restricted airflow, and skipping the vent check leads to repeat failures. What's In The Set Component Type Function 8557403 High-Limit Thermostat Auto-resetting Cuts power to the heating element if temperature exceeds safe limits, resets automatically once the dryer cools. 8318314 Thermal Fuse One-time, non-resettable Backup safety device — permanently opens the circuit if temperature exceeds safe limits. Must be replaced once blown. Common Problems This Set Fixes Dryer runs but produces no heat at all Dryer won't start at all — no lights, no tumble, no response Drying takes noticeably longer than it used to Dryer overheating before shutting down Dryer that stopped working suddenly after running unusually hot Repeated thermal fuse failures on a dryer with a known venting issue Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermostat set directly replaces the following OEM and cross-reference part numbers: 280148, 1175772, 280148VP, PD00002627, FIX991443, EAP991443, AH991443, AP3874047, AWP39427, EA991443, PS991443, 8318314, WP8557403, 8557403, 1180102, AP6013164, AWP48681, PD00003588, PS11746386 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat set is compatible with select Whirlpool electric dryers, and also fits select Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, KitchenAid, and Norge dryers built on the Whirlpool platform, including model numbers such as: 7MWED5620HW0, 7MWED5620HW1, 7MWED6613HC0, 7MWED6613HC1, 7MWED6613HW0, 7MWED6613HW1 MED5500FC1, MED5500FC2, MED5500FW1, MED5500FW2 MED5630HC0, MED5630HC1, MED5630HC2, MED5630HW0, MED5630HW1, MED5630HW2 MED6000XG0, MED6000XG1, MED6000XG2, MED6000XR0, MED6000XR1, MED6000XW0, MED6000XW1, MED6000XW2 MED6630HC0, MED6630HC1, MED6630HC2, MED6630HW0, MED6630HW1, MED6630HW2 MED7000XG0, MED7000XG1, MED7000XR0, MED7000XR1, MED7000XW0, MED7000XW1, MED7000XW2 MED7230HC0, MED7230HC1, MED7230HC2, MED7230HC3, MED7230HW0, MED7230HW1, MED7230HW2, MED7230HW3 MED8200FC1, MED8200FC2, MED8200FW1, MED8200FW2 Note: Always verify your full model number before ordering, since Whirlpool uses several different thermostat and fuse designs across its dryer lineup. This set is commonly purchased alongside heating element WP8544771. Contact our support team with your model number if you're unsure. Key Features 2-piece set: 8557403 auto-resetting high-limit thermostat and 8318314 one-time thermal fuse Resolves "no heat," "won't start at all," "takes too long to dry," and "overheating" symptoms Addresses two overheat-protection thresholds in the same circuit at once Commonly purchased alongside heating element WP8544771 No special tools required for installation Replaces 280148VP, 1175772, AP3874047, PS991443, EAP991443, and 314634 Compatible with Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, KitchenAid, and Norge electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Set Part Number 280148 OEM Part Number 280148 Set Contents 1x High-Limit Thermostat (8557403), 1x Thermal Fuse (8318314) Condition Aftermarket Replacement Application Whirlpool Electric Dryers High-Limit Thermostat Type Automatically resetting Thermal Fuse Type One-time use, non-resettable Companion Heating Element WP8544771 (commonly used together) Repair Difficulty Easy to Moderate — no special tools required Compatible Brands Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, KitchenAid, Norge Installation Notes ⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel, near the heating element and blower housing where both components are mounted. Photograph the wiring connections before disconnecting anything, since the thermostat and fuse can be easy to swap positions by mistake. Remove each old component from its mounting position, noting orientation, and disconnect its wiring. Before reassembling, fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. Restricted airflow is the leading cause of failure for both of these components, and skipping the vent check often leads to repeat failures even with new parts installed. Install the new 8557403 thermostat and 8318314 thermal fuse from this set in the same positions as the parts they replace, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), work gloves. Frequently Asked Questions Why replace both the thermostat and the fuse together instead of just the one that failed? These two parts protect the same circuit at different thresholds and tend to fail from the same underlying cause. If the high-limit thermostat isn't regulating temperature correctly, the thermal fuse often ends up blowing as the backup safety measure. Replacing only one risks the other failing again shortly after, so they're sold and serviced together as a set. I replaced this set and the dryer failed again. What should I check? This is a strong sign the underlying cause — almost always restricted airflow — was never addressed. Thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. Failing to correct a venting issue will cause repetitive failures of this set even when it's brand new. Should I replace the heating element at the same time? It's worth considering if your dryer's heating element (commonly WP8544771 on compatible models) is original and has been running alongside a failing thermostat, since sustained overheating can stress the element as well. It's not required, but since you'll already have the panel open for this repair, it's a reasonable time to inspect the element for visible damage. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the temperature thresholds and mounting configuration of the original 280148 high-limit thermostat and thermal fuse set used in compatible Whirlpool, Kenmore, Maytag, Amana, Roper, and related electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3387134 - 3392519 Dryer Cycling Thermostat and Thermal Fuse Set - Compatible with Whirlpool, Kenmore, Maytag Product Description Maintain safe and efficient dryer operation with the XPARTCO 3387134 - 3392519 Dryer Cycling Thermostat and Thermal Fuse Set. This replacement kit includes one cycling thermostat (3387134, L155-25) and one thermal fuse (3392519), designed as a replacement for select Whirlpool, Kenmore, Maytag, and other compatible dryers. The cycling thermostat regulates drum temperature, while the thermal fuse prevents overheating by cutting power if temperatures exceed safe limits. This set addresses issues like overheating, insufficient heat, no heat, or prolonged drying times. Test the thermal fuse first if the dryer won't heat, as it typically fails before the thermostat. Note: Includes (1) cycling thermostat and (1) thermal fuse. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: Cycling Thermostat: WP3387134, 3387134, 3387135, 3387139, 3-6910, 306910, 326801, 661512, L150-15F, L155-25F, AP6008270, PS11741405. Thermal Fuse: 3392519, WP3392519, 3388651, WE4X857, G4AP0500, 6L4101091C, ET401, 3388651, 694511, 80005, PS11741460, AP6008325. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: LE5700XKW0, LE5920XKW0, WED4815EW1, WED4910XQ1, WED5300SQ0 Kenmore: 110.97591420, 110.97591220, 110.97592420, 110.60072990 Maytag: MDE5500AYW, MDE6000AYW, MDE7600AYW Roper: RED4440VQ1, REX5634KQ1 Amana: NED4655EW0 KitchenAid: KEYE760WWH0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Amana, KitchenAid, and other dryers. 🔧 Specifications: Replacement kit with one cycling thermostat (L155-25 SPST, 120V, 2W) and one thermal fuse (250°F limit, non-resettable). 💪 Reliable Performance: Regulates drum temperature and prevents overheating for safe, efficient drying. 🛠️ Easy Installation: Requires a screwdriver and pliers; typically installed in 15–30 minutes. 🛡️ Effective Fixes: Resolves overheating, insufficient heat, no heat, or prolonged drying times. Product Specification Part Number: XPARTCO 3387134 - 3392519 Component Type: Dryer cycling thermostat and thermal fuse kit Material: Plastic and metal Electrical Specs: Cycling Thermostat: 120V, 2W; L155-25 SPST, opens at 155°F, closes at 130°F  Thermal Fuse: 250°F limit, 125/250V, non-resettable Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running safely and efficiently today! Add to cart now for a reliable fix!

Read more less