Search results for "Washer Lid Switch"

W11457841 Genuine OEM Whirlpool Washer Lid Strike The W11457841 is a Genuine OEM Whirlpool replacement washer lid strike compatible with select Whirlpool, Maytag, and Kenmore HE top-load washers — including the Whirlpool WTW5100, WTW5105, WTW6120, WTW7120, WTW8120, WTW8127 series, and the Maytag MVW6200, MVW6230, MVW7230, MVW7232, MVW8230 series. The lid strike is the plastic component attached to the underside of the washer lid that physically engages the lid lock mechanism when the lid is closed. As the lid lowers into place, the strike enters the lock slot and activates the lid switch — signaling the control board that the lid is securely closed and the washer is safe to start agitation and spin. When the lid strike fails — typically by breaking off, cracking, or wearing down — the lid lock can't be properly activated, and the washer will not start, will stop mid-cycle, or will refuse to advance to the spin cycle. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W11457841 is the current production part, directly superseding W11091027. It also replaces 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028. Installation is fast and simple — a counterclockwise twist removes the old strike, and a clockwise twist installs the new one. Installs in under 5 minutes, no special tools required. Quick Answer The W11457841 Genuine OEM Whirlpool Washer Lid Strike fixes Whirlpool, Maytag, and Kenmore HE top-load washers that won't start, won't lock the lid, stop mid-cycle, or won't advance to spin because the lid strike is broken or worn. Plastic strike that attaches to the underside of the washer lid and activates the lid lock and switch. Twist-in installation. Genuine OEM. Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, PS16218028. Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series. Common Problems This Part Fixes Washer not starting — lid strike not engaging the lid lock Lid won't lock at the start of the cycle Washer stops mid-cycle with a lid-related fault Washer fills with water but won't agitate or advance to spin Lid strike visibly broken, cracked, or missing on the underside of the lid Strike worn down — physically fits the lock slot but no longer activates the lid switch Repeated lid lock errors despite the lid appearing to close normally Replaces Part Numbers This washer lid strike directly replaces the following OEM and cross-reference part numbers: W11457841, W11091027, AP6987306, AWP44638, PD00061788, EAP16218028, PS16218028. W11457841 is the current production part superseding W11091027. Contact our support team with your model number if you need confirmation before ordering. Compatibility This lid strike is compatible with select HE top-load washers from the following brands and series: Whirlpool top-load washers — WTW5100HC0, WTW5100HC1, WTW5100HC2, WTW5100HW0, WTW5100HW1, WTW5100HW2 series Whirlpool top-load washers — WTW5105HC0, WTW5105HC1, WTW5105HC2, WTW5105HW0, WTW5105HW1, WTW5105HW2 series Whirlpool top-load washers — WTW6120HC0, WTW6120HC1, WTW6120HC2, WTW6120HW0, WTW6120HW1, WTW6120HW2 series Whirlpool top-load washers — WTW7120HC0, WTW7120HW0 series Whirlpool top-load washers — WTW8120HC0, WTW8120HW0 series Whirlpool top-load washers — WTW8127LC0, WTW8127LC1, WTW8127LW0 series Maytag top-load washers — MVW6200KW0, MVW6200KW1, MVW6200KW2, MVW6200KW3 series Maytag top-load washers — MVW6230HC0, MVW6230HC1, MVW6230HC2, MVW6230HW0, MVW6230HW1, MVW6230HW2 series Maytag top-load washers — MVW6230RHW0, MVW6230RHW1, MVW6230RHW2 series Maytag top-load washers — MVW7230HC0, MVW7230HW0, MVW7230HW1 series Maytag top-load washers — MVW7232HC0, MVW7232HW0, MVW7232HW2 series Maytag top-load washers — MVW8230HC0 series Kenmore / Sears top-load washers (Whirlpool-built — select 110-series models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Plastic strike attaches to the underside of the washer lid and engages the lid lock mechanism when the lid closes Activates the lid switch to signal the control board that the lid is securely closed and the washer is safe to start Twist-in/twist-out installation — no tools or hardware required; counterclockwise to remove, clockwise to install Current production part — directly supersedes W11091027 Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028 Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series HE top-load washers, plus select Kenmore Whirlpool-built models Fast DIY repair — installs in under 5 minutes Product Specifications Part Number W11457841 Supersedes W11091027 Part Type Washer Lid Strike Condition Genuine OEM Application HE Top-Load Washers (Whirlpool/Maytag/Kenmore platform) Material High-strength plastic Installation Twist-in (clockwise) / twist-out (counterclockwise) — no tools required Mounting Location Underside of washer lid Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer lid and locate the lid strike on the underside of the lid — it's the small plastic peg that drops into the lock slot when the lid is closed. To remove the old strike: rotate the strike counterclockwise until the retaining tab breaks free and pulls back, then pull the old strike straight out. To install the new W11457841: align it with the mounting hole in the same orientation as the old one, and rotate clockwise until you hear or feel the retainer tab click into place. Close the lid and confirm the strike engages the lock slot properly. Restore power, start a test cycle, and confirm the lid locks and the washer begins normal operation. Tools needed: work gloves only — no tools required for the strike itself. Frequently Asked Questions What's the difference between the lid strike, lid lock, and lid switch? These three components work together as a safety system. The lid strike (W11457841) is the small plastic peg attached to the underside of the lid that physically enters the lock slot when the lid closes. The lid lock is the mechanism in the washer cabinet that grips the strike and physically locks the lid closed during the spin cycle. The lid switch is the electrical sensor inside the lock assembly that signals the control board when the strike is engaged. If the strike is broken or missing, none of the three can do their job — even if the lock and switch are working perfectly. Replacing just the strike often resolves "won't start" issues without needing to replace the more expensive lock assembly. What is the difference between W11457841 and W11091027? These are the same lid strike across production revisions. W11091027 was the earlier OEM part number, and W11457841 is the current production version that Whirlpool issued as a direct replacement. Both parts are physically and functionally identical — if your washer's parts diagram shows W11091027, the W11457841 is the correct current replacement, and this listing covers both numbers. My washer won't start and the lid seems to close normally — could this be the strike? Yes, this is one of the most common symptoms of lid strike failure on compatible Whirlpool and Maytag washers. Even though the lid appears to close, if the strike has cracked or worn down it may not physically engage the lock or activate the switch correctly. Visually inspect the strike on the underside of the lid — if it's broken, missing, or chipped, replacement is straightforward. If the strike looks intact and the washer still won't start, the lid lock assembly itself or the wiring harness may need attention. Do I really not need any tools to install this? Correct — the W11457841 lid strike uses a twist-in design with no screws or hardware. To remove the old strike, rotate it counterclockwise until the internal retaining tab breaks free, then pull it out. To install the new one, push it into the mounting hole and twist clockwise until it clicks into place. The whole replacement typically takes under 5 minutes once you have the new part in hand. Work gloves are recommended to protect your hands while gripping the small plastic part, but no other tools are needed. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same lid strike installed in compatible Whirlpool, Maytag, and Kenmore HE top-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10482836 Washer Lid Lock & Latch Assembly The XPARTCO W10482836 is an aftermarket replacement lid lock and latch assembly for select Whirlpool and Maytag washers, replacing Whirlpool parts W10482836 and WPW10482836. The latch keeps the washer lid closed during operation. If the lid is not latched, the washer's door switch prevents the washer from running, so a defective latch can stop the washer from starting or spinning. The assembly includes the latch mechanism and the connecting wire to the washer's electrical system. Check your model number before ordering. Quick Answer The XPARTCO W10482836 Lid Lock & Latch Assembly replaces the lid latch on a compatible Whirlpool or Maytag washer when it no longer locks or latches. Replaces W10482836 and WPW10482836. Classic symptoms: the washer won't start, the lid won't lock or unlock, or the washer won't spin. Common Problems This Part Fixes Washer won't start Lid won't lock or unlock, or won't stay closed Washer won't spin or agitate Washer stops mid-cycle Damaged lid latch Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This lid lock and latch assembly directly replaces the following part numbers: WPW10482836, W10482836, 3020730, AP6022148, AWP50516, EAP11755478, PD00022780, PS11755478 Whirlpool uses different lid latch numbers for different washers (for example W10404050), and they are not interchangeable by number alone. If your old latch shows a different number, contact our support team and we'll check whether it matches. Compatibility This lid lock and latch assembly is listed for Whirlpool and Maytag washers, including these examples: Maytag MVW18MNBWW0, MVW18CSBWW0, MVW18PDAWW0, MAT20PDAXW0 Maytag MVWP575GW0, MVWP576KW0 Whirlpool CAE2743BQ0, CAE2793BQ0, QCAE2733BQ0, QCAE2735FQ0 Note: The models above are a small sample, not a full list. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Aftermarket replacement for the Whirlpool W10482836 lid lock and latch Includes the latch mechanism and connecting wire Keeps the lid locked from the start of the cycle until it finishes Replaces WPW10482836 Product Specifications Part Number XPW10482836 OEM Part Number WPW10482836 Part Type Washer Lid Lock & Latch Assembly Condition Aftermarket Replacement Includes Latch Mechanism and Connecting Wire Quantity 1 Assembly Application Select Whirlpool and Maytag Washers Installation Notes ⚠️ Unplug Power Before Installing Unplug the washer before you begin. Remove the top panel or access cover per your model's service guide, note how the wire connector attaches, and unscrew and remove the old latch. Position and secure the new latch, reconnect the wire, and refit the panel. Restore power and test that the lid locks and the washer starts. If the washer still won't run, test the latch switches for continuity against your wiring diagram. Frequently Asked Questions My washer won't start or the lid won't lock. Is this the part I need? It can be. Inspect the latch for damage first. If the latch looks fine, test its switches for continuity against your wiring diagram. Other parts, such as the control board, can cause the same symptoms. Is this an OEM or aftermarket part? This is an aftermarket replacement from XPARTCO, made to replace Whirlpool parts W10482836 and WPW10482836. If you specifically need a genuine Whirlpool part, contact our support team. Is this the same as other Whirlpool lid latch assemblies? Not necessarily. Whirlpool uses different lid latch numbers for different washers. Match the part number and your model number, or contact our support team and we'll check for you. Will this fit my washer? It is listed for select Whirlpool and Maytag models, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM WPW10482836 Washer Lid Lock & Latch Assembly The Genuine OEM Whirlpool WPW10482836 is the lid lock and latch assembly for select Whirlpool and Maytag washers. The latch keeps the washer lid closed during operation. If the lid is not latched, the washer's door switch prevents the washer from running, so a defective latch can stop the washer from starting or spinning. This is the original Whirlpool part, not an aftermarket equivalent. The assembly includes the latch mechanism and the connecting wire to the washer's electrical system. Check your model number before ordering. Quick Answer The Genuine OEM WPW10482836 Lid Lock & Latch Assembly replaces the lid latch on a compatible Whirlpool or Maytag washer when it no longer locks or latches. Replaces W10482836. Classic symptoms: the washer won't start, the lid won't lock or unlock, or the washer won't spin. Common Problems This Part Fixes Washer won't start Lid won't lock or unlock, or won't stay closed Washer won't spin or agitate Washer stops mid-cycle Damaged lid latch Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This lid lock and latch assembly replaces or supersedes the following part numbers: WPW10482836, W10482836, 3020730, AP6022148, AWP50516, EAP11755478, PD00022780, PS11755478 Whirlpool uses different lid latch numbers for different washers (for example W10404050), and they are not interchangeable by number alone. If your old latch shows a different number, contact our support team and we'll check whether it matches. Compatibility This lid lock and latch assembly is listed for Whirlpool and Maytag washers, including these examples: Maytag MVW18MNBWW0, MVW18CSBWW0, MVW18PDAWW0, MAT20PDAXW0 Maytag MVWP575GW0, MVWP576KW0 Whirlpool CAE2743BQ0, CAE2793BQ0, QCAE2733BQ0, QCAE2735FQ0 Note: The models above are a small sample, not a full list. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool part, not an aftermarket equivalent Includes the latch mechanism and connecting wire Keeps the lid locked from the start of the cycle until it finishes Replaces W10482836 Product Specifications Part Number WPW10482836 OEM Part Number WPW10482836 Part Type Washer Lid Lock & Latch Assembly Condition Genuine OEM Manufacturer Whirlpool Includes Latch Mechanism and Connecting Wire Quantity 1 Assembly Application Select Whirlpool and Maytag Washers Installation Notes ⚠️ Unplug Power Before Installing Unplug the washer before you begin. Remove the top panel or access cover per your model's service guide, note how the wire connector attaches, and unscrew and remove the old latch. Position and secure the new latch, reconnect the wire, and refit the panel. Restore power and test that the lid locks and the washer starts. If the washer still won't run, test the latch switches for continuity against your wiring diagram. Frequently Asked Questions My washer won't start or the lid won't lock. Is this the part I need? It can be. Inspect the latch for damage first. If the latch looks fine, test its switches for continuity against your wiring diagram. Other parts, such as the control board, can cause the same symptoms. Is this an OEM or aftermarket part? This is a genuine OEM part from Whirlpool, not an aftermarket equivalent. Is this the same as other Whirlpool lid latch assemblies? Not necessarily. Whirlpool uses different lid latch numbers for different washers. Match the part number and your model number, or contact our support team and we'll check for you. Will this fit my washer? It is listed for select Whirlpool and Maytag models, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11670519 Genuine OEM Whirlpool Washer Lid Lock Latch Assembly The W11670519 is a genuine Whirlpool OEM lid lock latch assembly for Maytag top-load washers on the Cabrio-style MVW platform. Unlike a simple mechanical lid switch, this is a true electronic lid lock: a 3-wire connector feeds the assembly, which both senses whether the lid is closed and physically locks it shut once a cycle with spin is underway. The control won't allow the washer to spin — and on many cycles won't even let it start — until this assembly confirms the lid is closed and locked, which is why a failing latch produces such a wide range of symptoms: a washer that won't start, a lid that won't lock or won't release, cycles that stall or interrupt partway through, or a washer that fills and agitates but refuses to spin. Built from high-strength, wear-resistant ABS and PP plastic with a precision locking mechanism, this assembly is designed to prevent the lid from popping open mid-spin, which protects against water leakage and the safety hazard of an open lid on a spinning basket. Common failure modes include a locking mechanism that has worn out and can no longer engage or release reliably, a broken internal switch that stops signaling lid status to the control board, and simple wear from years of daily cycling. It directly replaces W11368616, AP7214714, PD00085482, 4981394, PS17215992, and EAP17215992. As a genuine OEM part, the W11670519 is manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. Quick Answer The W11670519 Genuine OEM Whirlpool Washer Lid Lock Latch Assembly fixes Maytag top-load washers on the Cabrio-style MVW platform where the washer won't start, the lid won't lock or won't release, the washer fills and agitates but won't spin, the cycle stalls or interrupts, or the lid clicks repeatedly without locking. 3-wire electronic lid lock, ABS/PP construction. Replaces W11368616, AP7214714, PD00085482, 4981394, PS17215992, EAP17215992. This is a locking latch assembly, not a simple lid switch — it's a different design from the direct-drive and GE-platform lid switches elsewhere in our catalog. Common Problems This Part Fixes Washer won't start even though the lid is closed Lid won't lock, or locks but won't release when the cycle ends Washer fills and agitates normally but won't spin Persistent clicking sound from the lid area without the lid actually locking Cycle stalling or interrupting partway through Lid feels loose or doesn't seat and lock the way it used to Error code related to the lid lock displayed on the control panel Water leakage risk from a lid that isn't sealing and locking properly during spin Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer lid lock latch assembly directly replaces the following OEM and cross-reference part numbers: W11670519, W11368616, AP7214714, AWP46151, PD00085482, 4981394, PS17215992, EAP17215992 W11368616 was an earlier number for this same assembly. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid lock latch assembly is compatible with select Maytag top-load washers on the Cabrio-style MVW platform, including model numbers such as: MVW4505MW0, MVW4505MW1, MVW4505MW2 MVW5035MW1, MVW5035MW2 MVW5430MW1, MVW5430MW2, MVW5430PBK0, MVW5430PBK1 MVW5435PBK0, MVW5435PBK1, MVW5435PW0, MVW5435PW1 Note: This is an electronic locking latch assembly for the Maytag Cabrio-style MVW platform, and it is a different design from the simpler lid switches used on other Whirlpool platforms — including our 8318084 (direct-drive top-load), 3355806 (Whirlpool thin-twin), WH12X955 (GE combo/spacemaker), and WH01X29528 (GE front-load door lock) listings. None of those are interchangeable with this assembly. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which lid lock or switch your washer needs. Key Features Genuine Whirlpool OEM part — factory-specified locking mechanism and switch design Electronic lid lock — both senses lid position and physically locks the lid during spin cycles Resolves "won't start," "lid won't lock or release," "fills but won't spin," and "cycle interruptions" symptoms caused by latch failure 3-wire connector for a direct plug-and-play electrical connection Constructed from high-strength ABS and PP plastic for wear and aging resistance Precision-designed locking mechanism helps prevent accidental lid opening during spin Direct drop-in replacement — no modification required Replaces W11368616, AP7214714, PD00085482, 4981394, PS17215992, and EAP17215992 Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11670519 Part Type Washer Lid Lock Latch Assembly Condition Genuine OEM Brand Whirlpool / Maytag Application Maytag Cabrio-Style Top-Load Washers (MVW Platform) Electrical Connection 3-wire connector Material High-strength ABS and PP plastic Function Senses lid closure and physically locks the lid during spin Supersedes W11368616 Quantity 1 lid lock assembly Compatible Brands Whirlpool, Maytag Installation Notes ⚠️ Unplug Washer Before Starting — If The Lid Is Locked Shut, Release It Manually First Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. If the old latch has failed in the locked position and you can't open the lid, insert a small flathead screwdriver into the latch opening where the lock mechanism engages through the lid, and gently slide the mechanism back to release it — then prop the lid open so it can't re-close and re-lock while you work. Remove the two screws holding the top section (control panel, lid, and wash basket opening) and slide the top of the unit forward and up to remove it, then prop it securely (a sturdy support between the cabinet frame and the top panel works well) rather than relying on your hands to hold it up. With the top propped open, remove the plastic cowl that the lid latch sits inside, which also retains the lock mechanism. Unclip the wiring harness from the retaining clips running around the inside of the lid and let the assembly hang free. Photograph the wiring connections before disconnecting the 3-wire connector from the old assembly. At the back of the lid, two metal spring clips retain the mechanism — squeeze these with your fingers or a set of pliers to release the old assembly, then pop the new W11670519 into place the same way. Reconnect the 3-wire connector, reclip the wiring harness into its retaining clips, and reinstall the plastic cowl. Lower the top panel back into position, reinstall its retaining screws, and confirm the lid closes, latches, and locks correctly through a full test cycle including spin. Tools needed: small flathead screwdriver, Phillips screwdriver, pliers, a sturdy prop for the top panel, work gloves. Frequently Asked Questions My washer fills and agitates but won't spin. Is this the lid lock? Yes, this is one of the most common symptoms of a failing lid lock latch on this platform. The control requires confirmation that the lid is closed and locked before it will allow the higher-speed, higher-torque spin cycle to run, even if it's willing to run the gentler fill and agitate steps without full confirmation. If your washer gets partway through a cycle and simply refuses to spin, this assembly is a strong suspect. The lid keeps clicking but never actually locks. What does that mean? A repeated clicking sound without the lid actually locking usually points to a worn or failing internal locking mechanism inside this assembly — it's attempting to engage but can't complete the lock reliably. This is a textbook symptom that this part has worn out and needs replacement. My washer's lid is locked shut and won't open. How do I even get it open to do this repair? With the washer unplugged, you can usually manually release the lock: insert a small flathead screwdriver into the latch opening where the mechanism engages through the lid, and gently slide it back to disengage the lock. Once the lid is open, prop it so it can't fall shut and re-lock while you continue the repair. Is this the same part as the lid switches used on other Whirlpool washers? No. This is an electronic locking latch assembly specific to the Maytag Cabrio-style MVW platform, and it works differently from the simpler mechanical lid switches used on other Whirlpool-family platforms, including the direct-drive top-load switch, the Whirlpool thin-twin switch, and various GE-platform switches we also carry. These parts are not interchangeable with each other — always match the assembly to your specific washer platform. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same 3-wire electrical connection, locking mechanism, and ABS/PP construction as the lid lock latch assembly originally installed in your Maytag Cabrio-style washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WPW10619844 Washer Genuine OEM Lid Lock Assembly Replaces Part Numbers: WPW10619844, W10619844, W10059230, 3436901, 8563937, WPW10619844VP, AP6023438, PS11756782.  Description: This Lid Lock Assembly is a Genuine OEM part for specific Maytag, Kenmore, Whirlpool washing machine models. It ensures the washer lid is securely locked during operation, preventing it from being opened mid-cycle and ensuring safe and efficient washing. Common causes of a bad lid lock assembly can include wear and tear from frequent use, electrical issues such as short circuits, and physical damage from impact or mishandling. A malfunctioning lid lock can disrupt the washing cycle, leading to incomplete washes or safety concerns.

Read more less

XPARTCO W10820036 Washer / Dryer Door Switch The XPARTCO W10820036 is an aftermarket replacement door switch used on select Whirlpool-built combination washer/dryer units. This switch is a safety interlock: it detects whether the door is fully closed and latched, and it signals the control board that it is safe to run the motor, heater, and water valves. On a combo unit, this single interlock typically governs both the wash and dry portions of the cycle, since both functions share the same drum and door. If the switch fails to detect a closed door — or fails electrically even when the door is closed properly — the control will refuse to start the cycle, or will stop mid-cycle if the switch drops out while running. Typical failure modes for a part like this include a cracked or worn switch lever that no longer depresses fully when the door closes, internal contacts that have pitted or burned out from years of cycling, and a housing that has come loose from its mounting bracket so the plunger no longer lines up with the door strike. A functioning door switch should click firmly when the door closes and should show continuity across its terminals only when the lever is pressed. Quick Answer The XPARTCO W10820036 Washer/Dryer Door Switch is a door safety interlock switch for select Whirlpool-built combination washer/dryer units. It fixes units that won't start with the door closed, stop mid-cycle, or fail to register the door as closed even when it's latched properly. Note: this listing was built from general parts knowledge because current supplier and cross-reference data was not available at build time — see the note below before publishing. Common Problems This Part Fixes Washer/dryer combo won't start even though the door is fully closed Cycle stops partway through, as if the door had been opened Door doesn't feel like it's "clicking" or latching the way it used to Console shows a door-related error or won't advance past the door-closed step Intermittent operation — sometimes starts, sometimes doesn't, depending on how the door is closed Visibly cracked, loose, or broken switch housing or lever Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door switch directly replaces the following OEM part number: W10820036, 279347, 2-2770, 2-50062, 2-5415, 2020, 202770, 233480, 235462, 237194, 238775, 238980, 239868, 24198, 247207, 26000279347, 279290, 287219, 287220, 291679, 291697, 292212, 296141, 296144, 3347287, 338883, 3392266, 3397503, 3399991, 347207, 350526, 359230, 359484, 364090, 364091, 367034, 388322, 389105, 4273196, 4319330, 660308, 687429, 75958, 8224, 83333, 84144, 86628, 89556, 99788, 99838, LP210, AP5985146, AWP41434, EAP334185, PD00023982, PS11723153. No additional cross-reference numbers have been confirmed for this part yet. If you have a superseded or alternate number for your appliance, contact our support team and we will verify compatibility before you order. Compatibility This door switch is intended for select Whirlpool-built washer/dryer combination units, where a single door and drum serve both the wash and dry functions. Model list not yet confirmed: A specific compatible model list for W10820036 was not available at the time this page was built. Please verify your exact model number before ordering. Contact our support team with your model number and we will confirm fitment before you purchase. Key Features Aftermarket replacement door safety switch for Whirlpool-built washer/dryer combo units Detects whether the door is closed and latched before allowing the wash or dry cycle to run Resolves "won't start with door closed," "stops mid-cycle," and "door not detected" symptoms Direct drop-in replacement for the original W10820036 switch — no modification required Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPW10820036 OEM Part Number W10820036 Part Type Washer/Dryer Combo Door Safety Switch Condition Aftermarket Replacement Application Whirlpool-Built Washer/Dryer Combination Units Function Door-closed safety interlock for wash and dry cycles Quantity 1 switch Compatible Brand Whirlpool (combo platform) Installation Notes ⚠️ Unplug The Unit Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access to the door switch on combo units is typically through the front or top control panel — photograph the wiring harness before disconnecting it so you can match it exactly on reassembly. Confirm the new switch's lever aligns with the door strike before securing the mounting screws, and test for a firm, positive click when the door closes before restoring power and running a cycle. If your unit's service manual is available, follow its specific access and mounting steps rather than relying solely on general guidance. Frequently Asked Questions My combo unit won't start. Is this definitely the door switch? It's one of the most common causes when a unit refuses to start with the door visibly closed. Before replacing the switch, confirm the door is latching fully and that nothing (a stray sock, a bent strike bracket) is preventing it from closing all the way. If the door latches firmly but the unit still won't start, or a multimeter shows no continuity across the switch terminals when the lever is pressed, the switch itself is the likely culprit. Does this switch control both the washer and dryer functions? On combination washer/dryer units, yes — a single door and drum typically serve both functions, so one door switch acts as the safety interlock for both the wash and dry portions of the cycle. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the mounting, switching function, and door-interlock behavior of the original W10820036 switch used in compatible combination washer/dryer units. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM W11307244 Washer Lid Lock Assembly The Genuine OEM Whirlpool W11307244 is a lid lock assembly for select top-load washers from Whirlpool, Maytag, Kenmore and related brands. It keeps the lid locked during the wash and spin cycles, and the washer uses it to know the lid is closed. A faulty lid lock can leave the lid unable to close or open, or keep the washer from starting a load or spinning. This is the original Whirlpool part, not an aftermarket equivalent. It is sold individually. Check your model number before ordering, because lid locks vary by washer. Quick Answer The Genuine OEM W11307244 Washer Lid Lock Assembly replaces a faulty lid lock on a compatible top-load washer. Replaces W10838613 and W11253733. Classic symptoms: the lid won't close or open, the washer won't start or agitate, or it won't spin. Common Problems This Part Fixes Lid won't close or won't open Washer won't start a load because it doesn't detect the lid as closed Washer won't agitate or won't spin Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This lid lock assembly replaces or supersedes the following part numbers: W11307244, W10682535, W10838613, W10838613VP, W11253733, AP6832601, AWP44097, EAP12704713, PD00048394, PS12704713 If your old lid lock shows a different number, contact our support team and we'll check whether it matches. Compatibility This lid lock assembly is listed for top-load washers from Whirlpool, Maytag, Kenmore, Crosley and Amana, including these examples: Whirlpool WTW4616FW3, WTW4955HW0, WTW4855HW2, 7MWTW1700EM0 Maytag 7MMVWC417FW0 Kenmore 11020232712, 11022352511, 11020222511, 11025132411 Crosley CAW9352EW2 Note: The models above are a sample, not a full list, and the part fits only some models within each brand. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool part, not an aftermarket equivalent Locks the washer lid during wash and spin cycles Replaces two earlier Whirlpool lid lock part numbers Sold individually Product Specifications Part Number W11307244 OEM Part Number W11307244 Part Type Washer Lid Lock Assembly Condition Genuine OEM Manufacturer Whirlpool Quantity 1 Assembly Application Select Top-Load Washers Installation Notes ⚠️ Unplug The Washer And Shut Off The Water Unplug the washer and shut off the water supply before you start. Take a photo of the wiring connections before disconnecting anything, then transfer the connector to the new lid lock and secure it. If the washer still won't start or the lid won't lock, the cause may be the lid strike, the wiring or another component. Frequently Asked Questions My washer won't start or spin. Is this the fix? Possibly. A faulty lid lock can stop a washer from starting or spinning, but other parts can cause the same symptoms, so check the lid strike, wiring and other components too. Is this an OEM or aftermarket part? This is a genuine OEM part from Whirlpool, not an aftermarket equivalent. Does it come with a lid strike? No. This listing is for the lid lock assembly only. If your lid strike is damaged, it is a separate part. Will this fit my washer? It is listed for many top-load washers, but the model list above is only a sample and some models use a different lid lock. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO EBF61315802 Washer Door Lock Switch The XPARTCO EBF61315802 is an aftermarket replacement washer door lock switch assembly compatible with a wide range of LG front-load washers and Kenmore 796-series front-load washing machines. The door lock switch is mounted on the front panel just inside the door opening — when the door is closed, the door's striker engages the lock and the switch reports back to the control board that the door is securely closed. The lock then engages electromagnetically to physically prevent the door from being opened during the wash and spin cycles, eliminating the risk of water leaks and protecting the user from the high-speed spinning drum. When this part fails, the washer will not start (since the control board can't confirm the door is locked), will stop mid-cycle, may display DE1 or DE2 error codes, may not actually lock the door (allowing it to open during a cycle), or may leak water around the door. Rated 125V AC, 60Hz, with a 3-pin connector. It directly replaces EBF62534401, AP5672154, AP6992889, PS7792232, PS16223547, EAP7792232, 2667085, and PD00008063. Often replaced alongside the door lock strike (MFG63099101, sold separately), which is the matching component on the door itself. Installs in 15–20 minutes with basic hand tools — no full front panel removal needed on most models. Quick Answer The XPARTCO EBF61315802 Washer Door Lock Switch fixes LG and Kenmore 796-series front-load washers that won't start, won't lock the door, stop mid-cycle, display DE1 or DE2 error codes, allow the door to open during a cycle, or leak water around the door. 125V AC, 60Hz, 3-pin connector. Replaces EBF62534401, AP5672154, AP6992889, PS7792232, PS16223547, EAP7792232, 2667085, PD00008063. Often paired with the door lock strike (MFG63099101, sold separately). Common Problems This Part Fixes Washer won't start — control board not detecting a locked door Door fails to lock at the start of the cycle DE1 or DE2 error codes displayed on the control panel Washer stops mid-cycle due to a door lock fault Door pops open or unlatches during the wash or spin cycle (safety concern) Water leaking around the door during operation — door not sealing because the lock isn't fully engaging Stuck, aged, worn, or broken door lock Door open/close action no longer smooth — lock binding Repeated mid-cycle shutdowns or interruptions Replaces Part Numbers This door lock switch directly replaces the following OEM and cross-reference part numbers: EBF61315802, EBF62534401, AP6992889, PS16223547, ALG54705, AP5672154, PD00008063, PS7792232, B088MG37Y9 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door lock switch is compatible with select LG and Kenmore 796-series front-load washers, including: LG front-load washers — WM1388HW, WM1455HWA series LG front-load washers — WM3050CW, WM3080CW, WM3170CW, WM3180CW series LG front-load washers — WM3250HRA, WM3250HVA, WM3250HWA, WM3270CW series LG front-load washers — WM3370HRA, WM3370HVA, WM3370HWA, WM3400CW, WM3460CV, WM3488HS, WM3488HW, WM3499HVA, WM3500CW, WM3555HWA series LG front-load washers — WM3570HVA, WM3570HWA, WM3600HVA, WM3670HVA, WM3670HWA, WM3700HVA, WM3700HWA series LG front-load washers — WM3770HVA, WM3770HWA, WM3900HBA, WM3900HWA, WM3997HWA, WM3998HBA series LG front-load washers — WM4070HVA, WM4070HWA, WM4200HBA, WM4200HWA, WM4270HVA, WM4270HWA, WM4370HKA, WM4370HWA, WM4500HBA series LG front-load washers — WM5000HVA, WM5000HWA, WM8000HVA, WM8000HWA, WM8100HVA, WM8100HWA, WM8500HVA series LG front-load washers — WM9000HVA, WM9000HWA, WM9500HKA series LG WashTower units — WKE100HVA, WKE100HWA, WKEX200HBA, WKEX200HWA, WKG101HVA, WKG101HWA, WKGX201HBA series LG Studio models — GCWP1069CD/CD1/CD2/CD3, GCWW1069CD7, GCWW1069CS7 series Kenmore / Sears front-load washers — 796-series (79641002610, 79641072310, 79641073310, 79641182310, 79641183310, 79641262610, 79641282310, 79641283310, 79641302610, 79641303610, 79641382410, 79641383410, 79641392610, 79641482410, 79641572210, 79641573210, 79641582410, 79641962610, 79641963610, 79641982410, and many related models) Note: The door lock switch (EBF61315802) and the door lock strike (MFG63099101) are two separate components that work together — if both have failed or are worn, replacing them together as a matched set ensures reliable door locking and prevents premature wear on the new switch. Always verify your model number before ordering. Key Features Door lock switch assembly — detects when the door is closed and electromagnetically locks it during wash and spin cycles Resolves DE1 and DE2 error codes caused by door lock failure on compatible LG and Kenmore washers Prevents water leaks and protects the user by ensuring the door cannot open during operation 125V AC, 60Hz — correct electrical specifications for compatible LG and Kenmore washers 3-pin connector for secure wire harness fit Replaces EBF62534401, AP5672154, AP6992889, PS7792232, PS16223547, EAP7792232, 2667085, and PD00008063 Compatible with LG WM1388, WM3050, WM3170, WM3250, WM3370, WM3500, WM3570, WM3670, WM3770, WM3900, WM3997, WM4070, WM4270, WM4370, WM5000, WM8000, WM8100, WM8500, WM9000, WM9500 series and Kenmore 796-series front-load washers Compatible with LG WashTower (WKEX, WKE, WKG, WKGX) units Often replaced together with the door lock strike (MFG63099101, sold separately) Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools (no full front panel removal needed on most models) Product Specifications Part Number EBF61315802 Part Type Washer Door Lock Switch Assembly Condition Aftermarket Replacement Application Front-Load Washers (LG / Kenmore Samsung-built platform) Voltage 125V AC Frequency 60 Hz Connector 3-pin connector Lock Type Electromagnetic Error Codes Resolved DE1, DE2 (door lock errors) Often Paired With Door Lock Strike (MFG63099101, sold separately) Compatible Brands LG, Kenmore (LG-built) Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. On most LG and Kenmore front-load models, you can replace the door lock switch without removing the whole front panel — a much faster repair than expected. Open the washer door (if the door is stuck locked, use a putty knife to pry the white latch on the door lock assembly through the bottom service opening, then open the door). Remove the spring-loaded wire clamp securing the door boot to the front panel — needle-nose pliers help here. Peel back the rubber door boot from the front panel to expose the rear of the door lock switch. Remove the 2 Phillips screws holding the switch to the front panel. Reach in and pull the switch out through the boot opening. Disconnect the wire harness from the old switch. Connect the wire harness to the new EBF61315802, position it in place, and secure with the 2 mounting screws. Press the rubber door boot back fully into the groove at the front panel — this is the trickiest part of the install (an extra pair of hands helps). Reinstall the spring-loaded wire clamp around the boot to secure it. Restore power and test by closing the door and starting a cycle. Tools needed: Phillips screwdriver, needle-nose pliers, putty knife (for stuck doors), work gloves. Frequently Asked Questions What do error codes DE1 and DE2 mean on LG washers? DE (Door Error) codes on LG front-load washers indicate the control board cannot confirm the door is properly closed and locked. DE1 typically appears when the door switch reports the door as open at the start of a cycle, and DE2 typically appears when the door signal is lost during a cycle. Both can be caused by a failed door lock switch, a worn or broken door lock strike (MFG63099101) on the door itself, or a damaged wiring harness. Replacing the EBF61315802 door lock switch resolves these codes when the switch is the cause; if the codes return after replacement, the strike on the door or the harness should be inspected next. Do I need to replace the door lock strike (MFG63099101) too? Not always, but often. The door lock strike is the matching component mounted on the door itself — it's the part that the switch's electromagnetic lock grips when the door closes. If the strike is worn, cracked, or its plastic teeth are broken, the new switch won't lock reliably even if it's working perfectly. Inspect the strike on the door for visible damage before replacing just the switch. Many repair scenarios call for replacing both at the same time, since both wear together and the parts complement each other. My washer door is stuck closed — how do I get it open to install this? If the door is stuck in the locked position because the existing switch has failed, you can use a putty knife or thin flat tool to manually release the door lock through the bottom service opening of the washer. Reach in through the access panel at the lower front of the unit and locate the white plastic latch on the back of the door lock assembly — gently push or pry it to release the mechanism. The door should then open. Once open, you can proceed with the installation. Always disconnect power from the washer before attempting this. Do I really not need to remove the front panel? Correct — on most LG and Kenmore front-load models, you can replace the door lock switch by working through the door opening after pulling back the rubber door boot. This avoids the much more involved process of removing the entire front panel. The trickiest part of the repair is pressing the rubber door boot back into its groove on the front panel after the switch is installed — an extra pair of hands is helpful for this step. The whole repair typically takes 15–20 minutes. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the electrical specifications (125V AC, 60Hz), 3-pin connector configuration, electromagnetic lock function, and dimensions of the original EBF61315802 door lock switch used in compatible LG and Kenmore 796-series front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11457841 Washer Lid Latch Strike The XPARTCO W11457841 is an aftermarket replacement washer lid latch strike compatible with select Whirlpool, Maytag, and Kenmore HE top-load washers — including the Whirlpool WTW5100, WTW5105, WTW6120, WTW7120, WTW8120, WTW8127 series, and the Maytag MVW6200, MVW6230, MVW7230, MVW7232, MVW8230 series. The lid latch strike is the plastic component attached to the underside of the washer lid that physically engages the lid lock mechanism when the lid is closed. As the lid lowers into place, the latch strike enters the lock slot and activates the lid switch — signaling the control board that the lid is securely closed and the washer is safe to start agitation and spin. When the lid latch strike fails — typically by breaking off, cracking, or wearing down — the lid lock can't be properly activated, and the washer will not start, will stop mid-cycle, or will refuse to advance to the spin cycle. This W11457841 aftermarket replacement is built to OEM-equivalent specifications and supersedes the earlier W11091027. It also replaces 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028. Installation is fast and simple — a counterclockwise twist removes the old strike, and a clockwise twist installs the new one. Installs in under 5 minutes, no special tools required. Quick Answer The XPARTCO W11457841 Washer Lid Latch Strike fixes Whirlpool, Maytag, and Kenmore HE top-load washers that won't start, won't lock the lid, stop mid-cycle, or won't advance to spin because the lid strike is broken or worn. Plastic latch strike that attaches to the underside of the washer lid and activates the lid lock and switch. Twist-in installation. Genuine OEM. Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, PS16218028. Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series. Common Problems This Part Fixes Washer not starting — lid latch strike not engaging the lid lock Lid won't lock at the start of the cycle Washer stops mid-cycle with a lid-related fault Washer fills with water but won't agitate or advance to spin Lid latch strike visibly broken, cracked, or missing on the underside of the lid Latch strike worn down — physically fits the lock slot but no longer activates the lid switch Repeated lid lock errors despite the lid appearing to close normally Replaces Part Numbers This washer lid latch strike directly replaces the following OEM and cross-reference part numbers: W11457841, W11091027, AP6987306, AWP44638, PD00061788, EAP16218028, PS16218028. W11457841 is the current production part superseding W11091027. Contact our support team with your model number if you need confirmation before ordering. Compatibility This lid latch strike is compatible with select HE top-load washers from the following brands and series: Whirlpool top-load washers — WTW5100HC0, WTW5100HC1, WTW5100HC2, WTW5100HW0, WTW5100HW1, WTW5100HW2 series Whirlpool top-load washers — WTW5105HC0, WTW5105HC1, WTW5105HC2, WTW5105HW0, WTW5105HW1, WTW5105HW2 series Whirlpool top-load washers — WTW6120HC0, WTW6120HC1, WTW6120HC2, WTW6120HW0, WTW6120HW1, WTW6120HW2 series Whirlpool top-load washers — WTW7120HC0, WTW7120HW0 series Whirlpool top-load washers — WTW8120HC0, WTW8120HW0 series Whirlpool top-load washers — WTW8127LC0, WTW8127LC1, WTW8127LW0 series Maytag top-load washers — MVW6200KW0, MVW6200KW1, MVW6200KW2, MVW6200KW3 series Maytag top-load washers — MVW6230HC0, MVW6230HC1, MVW6230HC2, MVW6230HW0, MVW6230HW1, MVW6230HW2 series Maytag top-load washers — MVW6230RHW0, MVW6230RHW1, MVW6230RHW2 series Maytag top-load washers — MVW7230HC0, MVW7230HW0, MVW7230HW1 series Maytag top-load washers — MVW7232HC0, MVW7232HW0, MVW7232HW2 series Maytag top-load washers — MVW8230HC0 series Kenmore / Sears top-load washers (Whirlpool-built — select 110-series models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Aftermarket replacement built to OEM-equivalent quality standards — direct fit for compatible Whirlpool platform washers Plastic latch strike attaches to the underside of the washer lid and engages the lid lock mechanism when the lid closes Activates the lid switch to signal the control board that the lid is securely closed and the washer is safe to start Twist-in/twist-out installation — no tools or hardware required; counterclockwise to remove, clockwise to install Current production part — directly supersedes W11091027 Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028 Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series HE top-load washers, plus select Kenmore Whirlpool-built models Fast DIY repair — installs in under 5 minutes Product Specifications Part Number W11457841 Supersedes W11091027 Part Type Washer Lid Latch Strike Condition Aftermarket Replacement Application HE Top-Load Washers (Whirlpool/Maytag/Kenmore platform) Material High-strength plastic Installation Twist-in (clockwise) / twist-out (counterclockwise) — no tools required Mounting Location Underside of washer lid Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer lid and locate the lid latch strike on the underside of the lid — it's the small plastic peg that drops into the lock slot when the lid is closed. To remove the old latch strike: rotate it counterclockwise until the retaining tab breaks free and pulls back, then pull the old latch strike straight out. To install the new W11457841: align it with the mounting hole in the same orientation as the old one, and rotate clockwise until you hear or feel the retainer tab click into place. Close the lid and confirm the latch strike engages the lock slot properly. Restore power, start a test cycle, and confirm the lid locks and the washer begins normal operation. Tools needed: work gloves only — no tools required for the strike itself. Frequently Asked Questions What's the difference between the lid strike, lid lock, and lid switch? These three components work together as a safety system. The lid latch strike (W11457841) is the small plastic peg attached to the underside of the lid that physically enters the lock slot when the lid closes. The lid lock is the mechanism in the washer cabinet that grips the strike and physically locks the lid closed during the spin cycle. The lid switch is the electrical sensor inside the lock assembly that signals the control board when the strike is engaged. If the strike is broken or missing, none of the three can do their job — even if the lock and switch are working perfectly. Replacing just the strike often resolves "won't start" issues without needing to replace the more expensive lock assembly. What is the difference between W11457841 and W11091027? These are the same lid latch strike across production revisions. W11091027 was the earlier OEM part number, and W11457841 is the current part number that superseded it. Both are physically and functionally identical — if your washer's parts diagram shows W11091027, the W11457841 is the correct current replacement, and this aftermarket part covers both numbers. My washer won't start and the lid seems to close normally — could this be the strike? Yes, this is one of the most common symptoms of lid latch strike failure on compatible Whirlpool and Maytag washers. Even though the lid appears to close, if the strike has cracked or worn down it may not physically engage the lock or activate the switch correctly. Visually inspect the latch strike on the underside of the lid — if it's broken, missing, or chipped, replacement is straightforward. If the latch strike looks intact and the washer still won't start, the lid lock assembly itself or the wiring harness may need attention. Do I really not need any tools to install this? Correct — the W11457841 lid latch strike uses a twist-in design with no screws or hardware. To remove the old latch strike, rotate it counterclockwise until the internal retaining tab breaks free, then pull it out. To install the new one, push it into the mounting hole and twist clockwise until it clicks into place. The whole replacement typically takes under 5 minutes once you have the new part in hand. Work gloves are recommended to protect your hands while gripping the small plastic part, but no other tools are needed. Is this a Genuine OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, twist-in mounting design, and lid switch activation function of the original W11457841 lid latch strike used in compatible Whirlpool, Maytag, and Kenmore HE top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO XPW11307244 Washer Lid Lock Assembly The XPARTCO XPW11307244 is a lid lock assembly for select top-load washers from Whirlpool, Maytag, Kenmore and related brands. It keeps the lid locked during the wash and spin cycles, and the washer uses it to know the lid is closed. A faulty lid lock can leave the lid unable to close or open, or keep the washer from starting a load or spinning. This is an aftermarket replacement from XPARTCO, made to replace Whirlpool part W11307244. If you specifically need a genuine Whirlpool part, contact our support team. It is sold individually. Check your model number before ordering, because lid locks vary by washer. Quick Answer The XPARTCO XPW11307244 Washer Lid Lock Assembly replaces a faulty lid lock on a compatible top-load washer. Made to replace Whirlpool W11307244, W10838613 and W11253733. Classic symptoms: the lid won't close or open, the washer won't start or agitate, or it won't spin. Common Problems This Part Fixes Lid won't close or won't open Washer won't start a load because it doesn't detect the lid as closed Washer won't agitate or won't spin Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This lid lock assembly is made to replace the following part numbers: W11307244, W10682535, W10838613, W10838613VP, W11253733, AP6832601, AWP44097, EAP12704713, PD00048394, PS12704713. If your old lid lock shows a different number, contact our support team and we'll check whether it matches. Compatibility This lid lock assembly is listed for top-load washers from Whirlpool, Maytag, Kenmore, Crosley and Amana, including these examples: Whirlpool WTW4616FW3, WTW4955HW0, WTW4855HW2, 7MWTW1700EM0 Maytag 7MMVWC417FW0 Kenmore 11020232712, 11022352511, 11020222511, 11025132411 Crosley CAW9352EW2 Note: The models above are a sample, not a full list, and the part fits only some models within each brand. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Aftermarket replacement from XPARTCO, made to replace Whirlpool W11307244 Locks the washer lid during wash and spin cycles Also made to replace W10838613 and W11253733 Sold individually Product Specifications Part Number XPW11307244 OEM Part Number W11307244 Part Type Washer Lid Lock Assembly Condition Aftermarket Replacement Quantity 1 Assembly Application Select Top-Load Washers Installation Notes ⚠️ Unplug The Washer And Shut Off The Water Unplug the washer and shut off the water supply before you start. Take a photo of the wiring connections before disconnecting anything, then transfer the connector to the new lid lock and secure it. If the washer still won't start or the lid won't lock, the cause may be the lid strike, the wiring or another component. Frequently Asked Questions My washer won't start or spin. Is this the fix? Possibly. A faulty lid lock can stop a washer from starting or spinning, but other parts can cause the same symptoms, so check the lid strike, wiring and other components too. Is this an OEM or aftermarket part? This is an aftermarket replacement from XPARTCO, made to replace Whirlpool part W11307244. If you specifically need a genuine Whirlpool part, contact our support team. Does it come with a lid strike? No. This listing is for the lid lock assembly only. If your lid strike is damaged, it is a separate part. Will this fit my washer? It is listed for many top-load washers, but the model list above is only a sample and some models use a different lid lock. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10335056 Washer Genuine OEM Water Level Switch Pressure Switch Replaces Part Numbers: W10335056, 1617123, 3366846, AH3408073, EA3408073, AP4566382, PS3408073, W10335056VP.  Description: This Pressure Switch is a Genuine OEM part for specific Whirlpool washing machine models. This part ensures your machine fills with the correct amount of water for the selected cycle, preventing overfilling or insufficient water levels that can lead to suboptimal washing results.    A faulty Pressure Switch can result from several issues, including clogging with detergent residue or debris, wear and tear from regular use, or electrical malfunctions affecting its responsiveness.     California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO DC96-01703H Washer Water Pressure Switch - Compatible with Samsung Washers Product Description Ensure your Samsung washer operates flawlessly with the replacement DC96-01703H Washer Water Pressure Switch. This replacement part is designed for select Samsung washing machines, providing precise water level control to prevent overfilling, underfilling, or water leakage. It resolves issues like error codes, inconsistent water levels, or failure to start wash cycles, delivering reliable performance for your appliance. Note: Disconnect power and water supply before installation. Verify model compatibility for proper fit. Replaces part numbers: DC96-01703H, PD00030634, EAP8764044, AP5799898, 3997570, PS8764044. Compatibility: Compatible with models including but not limited to: Samsung: WA48J7700AW/A2, WA48H7400AW/A2, WA50F9A7DSP/A2, WA52M7750AV/A4, WA56H9000AP/A2 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand Compatibility: Fits select Samsung washing machines. 🔥 Specifications: Water pressure switch with electrical connectors and 28" hose attachment. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires screwdriver, pliers; typically installed in 10–15 minutes. 🛡️ Effective Fixes: Resolves water level issues, error codes, and improper filling. Product Specification Part Number: XPDC96-01703H Component Type: Washer water pressure switch Mounting: Secures to washer control panel with screws or clips Operating Conditions: Suitable for washer environments Installation Notes: Safety First: Disconnect the washer from power and water sources before installation. Follow the owner’s manual for guidance. Shop for high-quality replacement appliance parts with a 30-day return policy. Fix your washer today! Add to cart now for a reliable solution!

Read more less