Search results for "dishwasher drain"

W11497943 Dishwasher Genuine Drain Pump Motor Replaces Part Numbers: W11497943, AP6994646, PS16221213, W11412663.   Description: This Drain Pump Motor is a Genuine OEM component for select Maytag, Kenmore, Whirlpool dishwasher models. This electric motor powers the drain pump to empty wash water from the tub at the end of cycles. Common causes of a bad pump motor include wear over extended use, moisture damage degrading electronics, or electrical faults from voltage fluctuations.

Read more less

WD21X25468 Genuine OEM GE Dishwasher Pressure Sensor Assembly The WD21X25468 is a Genuine OEM GE replacement dishwasher pressure sensor assembly compatible with a wide range of GE, GE Profile, GE Café, Hotpoint, Haier, and Monogram dishwashers in the GDF, GDT, GDP, PDT, CDT, ZDT, QDP, and HDF series. The pressure sensor monitors water pressure inside the dishwasher tub during fill and drain cycles and sends real-time readings to the electronic control board. The control board uses these readings to calculate the correct amount of water needed for each wash cycle and to confirm that the tub has drained properly before advancing to the next cycle phase. When the pressure sensor fails — or when it becomes clogged with grease, food residue, or mineral buildup — the dishwasher may not fill with water, may overfill, may stop mid-cycle, may fail to drain correctly, or may display error codes H2O or FTD (Failure to Drain). This Genuine OEM part is manufactured by GE to factory specifications. It directly replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, and 265D3356P001. Sold individually. Installs in 15–20 minutes — a screwdriver is the only tool required for most models. Quick Answer The WD21X25468 Genuine OEM GE Dishwasher Pressure Sensor Assembly fixes GE dishwashers displaying error codes H2O or FTD (Failure to Drain), not filling with water, overfilling, stopping mid-cycle, or running excessive noise from the spray arms. Monitors water level and pressure — signals the control board to fill, wash, and drain correctly. Genuine OEM. Replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, 265D3356P001. Sold individually. Compatible with GE GDF, GDT, PDT, CDT, ZDT, QDP, HDF, and related series. Common Problems This Part Fixes Error code H2O displayed — dishwasher not receiving enough water or no water at all Error code FTD (Failure to Drain) displayed — sensor not confirming tub has drained Dishwasher not filling with water when a cycle is started Dishwasher overfilling — sensor not signaling the control board to stop filling Dishwasher stopping mid-cycle without completing the wash Excessive noise during operation — sensor not accurately controlling spray arm water pressure Dishwasher requires priming with water to start (filling the tub manually before it will run) Replaces Part Numbers This pressure sensor directly replaces the following OEM and cross-reference part numbers: WD21X25468, 265D3356P001, AGE24772, AP6976524, EAP12741258, OEM20929581, PD00067609, PS12741258. Contact our support team with your model number if you need confirmation before ordering. Compatibility This pressure sensor is compatible with a wide range of dishwashers from the following GE product lines: GE dishwashers — GDF450, GDF510, GDF511, GDF535, GDF550, GDF565, GDF570, GDF630, GDF640, GDF645 series GE dishwashers — GDT530, GDT535, GDT565, GDT580, GDT605, GDT625, GDT630, GDT635, GDT645, GDT695 series GE dishwashers — GDP615, GDP645, GDP665 series GE Profile dishwashers — PDT715, PDT775, PDT785 series GE Café dishwashers — CDT800, CDT875 series GE Monogram dishwashers — ZDT800, ZDT870, ZDT925, ZDT985 series Hotpoint dishwashers — HDF310, HDF330 series Haier dishwashers (select GE-platform models) GE / Café / Profile — QDP555 series Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Monitors water pressure inside the tub throughout fill and drain cycles — signals the control board to fill to the correct level and confirm complete drainage Resolves H2O and FTD error codes on compatible GE dishwashers Sensor can also fail due to grease or mineral buildup blocking the pressure port — cleaning may resolve the issue without replacement Replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, and 265D3356P001 Compatible with GE GDF, GDT, GDP, PDT, CDT, ZDT, QDP, HDF, and Hotpoint dishwasher series Sold individually Quick DIY repair — installs in 15–20 minutes with a screwdriver Product Specifications Part Number WD21X25468 Part Type Dishwasher Pressure Sensor Assembly (Pressure Switch) Condition Genuine OEM Application GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier Dishwashers Function Monitors tub water level and pressure — signals control board for fill and drain control Error Codes Resolved H2O (no/low water), FTD (Failure to Drain) Sold As Single sensor assembly Compatible Brands GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting Disconnect power and shut off the water supply before beginning. On most compatible GE models, the pressure sensor is located near the bottom of the dishwasher tub, accessible after removing the lower front kick panel (secured by one or two screws). The sensor assembly connects to a small hose and a wiring harness connector. Tip: before replacing the sensor, remove it and inspect the pressure port and hose for grease, food residue, or mineral buildup — a clogged sensor port can cause H2O and FTD errors without the sensor itself being electrically failed. Clean the port and hose with warm water and a small brush, reinstall, and test the dishwasher. If the error codes persist after cleaning, replace the WD21X25468 sensor. To replace: disconnect the hose and wiring harness from the old sensor, unclip or unscrew the sensor from its mounting bracket, and install the new sensor in the same position. Reconnect the hose and harness, restore power and water, and run a test cycle. Tools needed: Phillips screwdriver. Frequently Asked Questions What does the dishwasher pressure sensor do? The pressure sensor monitors the water pressure — and therefore the water level — inside the dishwasher tub throughout the wash cycle. It sends continuous readings to the electronic control board, which uses the data to determine how much water to add during fill, when to stop filling, and whether the tub has drained completely before advancing to the next cycle phase. An accurate pressure sensor is essential for the dishwasher to fill to the correct level (not too much, not too little), wash with the correct spray arm pressure, and drain fully before moving on to rinse or dry cycles. What do error codes H2O and FTD mean on GE dishwashers? H2O error code on compatible GE dishwashers indicates that the dishwasher is not detecting enough water in the tub — either water is not filling at all, or the pressure sensor is not sensing the water that has filled. FTD (Failure to Drain) code indicates the dishwasher has not confirmed that the tub has drained within the expected time. Both codes can be caused by a faulty pressure sensor, a clogged sensor port, a failed fill valve, a blocked drain system, or control board issues. The pressure sensor should be inspected and tested first since it is the most accessible and commonly replaced component for these two error codes. Should I try cleaning the sensor before replacing it? Yes — absolutely. The pressure sensor on GE dishwashers can produce H2O and FTD error codes when its pressure port or connected hose becomes clogged with grease, food residue, or hard water mineral deposits — even if the sensor itself is electrically intact. Before ordering a replacement, remove the sensor, inspect the pressure port opening, and clean it thoroughly with warm water and a small brush. Flush the connected hose to clear any buildup. Reinstall and run a test cycle. If the error codes return, the sensor has electrically failed and needs replacement with the WD21X25468. My dishwasher won't fill unless I pour water in manually first — is this the pressure sensor? Yes — this is a classic symptom of a clogged or failed pressure sensor. When the sensor port is blocked, the sensor reads zero pressure (empty tub) even when the dishwasher starts. In some cases the control board interprets this as a drainage confirmation and will not initiate the fill cycle. Pouring water into the filter manually raises the physical water level enough to trigger filling. Check and clean the sensor port as described above. If cleaning does not resolve the issue, replace the WD21X25468 sensor. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same pressure sensor assembly installed in compatible GE, GE Profile, GE Café, Hotpoint, and related brand dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

DC62-30314L Dishwasher Genuine OEM Water Valve 120V, 60Hz, single coil valve with GHT inlet.  Fits Specific Samsung Dishwashers Models. Replaces Part Numbers: DC62-30314L, AP5582579, PS4209101. Description: The Dishwasher Water Valve is an essential component for maintaining the optimal performance of your dishwasher. This genuine OEM part ensures reliable water flow control, allowing your dishwasher to fill and drain effectively during each cycle. Designed specifically for Samsung dishwashers, it guarantees a perfect fit and seamless integration with your appliance.  

Read more less

W11665769 Dishwasher Sump Pump and Motor Pump and Motor Assembly Replaces Part Numbers: W11665769, W11085683, W10917110, W11164469, AP7212556, PS16875975. Description: This dishwasher pump and motor assembly is compatible with specific Whirlpool, Maytag, Kenmore dishwasher models. It is supplied directly by the original manufacturer to ensure that it fits perfectly with your model. The pump and motor are responsible for moving water throughout the dishwasher during the wash cycle. The pump draws water from the tub and pumps it through various channels, such as the detergent dispenser, spray arms, and drain hose. The motor provides the power necessary to drive the circulation pump, causing the pump to rotate and circulate water. If the assembly is faulty, you will notice difficulties starting or filling the dishwasher, poor cleaning performance, incomplete cycles, and water leaks.

Read more less

W10428167 Dishwasher Pump and Motor Assembly Pump & motor assembly, circulation and drain are handled by this assembly Replaces Part Numbers: W10428167, 2024551, 3385003, 3385004, 8193511, 8193511A, 8283498, 8283502, AH3500988, EA3500988, AP5306229, PS3500988   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

Genuine Bosch OEM Bosch 00640476 Dishwasher Genuine OEM Terminal Box Original Bosch dishwasher terminal box with terminal block for select Bosch, Thermador, Gaggenau, and Kenmore dishwashers. Product Overview The Bosch 00640476 Dishwasher Terminal Box is a genuine OEM electrical connection enclosure used on compatible dishwashers. It houses the terminal block where household electrical power connects to the dishwasher wiring harness. This assembly is supplied with the terminal block. The separate wiring/terminal-box cover is not included; Bosch identifies the matching cover as part 00640477. Quick Answer 00640476 is a Genuine Bosch OEM dishwasher terminal box with terminal block. It replaces earlier part 640476. The cover is sold separately as 00640477. Common Problems This Part May Fix Dishwasher will not start because of a damaged power connection Burned, overheated, or melted terminal connections Loose or damaged line-voltage wiring connection Damaged terminal block or terminal-box housing Intermittent power caused by compromised terminal connections Replaces and Cross-References 00640476, 1378543, 640476, ABS11577, AP3962500, EAP8729475, PD00023793, PS8729475 Cross-reference numbers are provided for identification. Bosch 00640476 is the Genuine OEM part. Compatibility Used on select Bosch-built dishwashers sold under Bosch, Thermador, Gaggenau, and Kenmore brands. Verified model examples include: SHE55C05UC/58 SHE43F15UC/61 SHE4AM16UC/02 SHX3AM06UC/01 SHX3AR56UC/07 S36KMK15UC/05 DWHD410HPR/60 63013903010 63013909012 Important: This is only a partial compatibility list. Bosch uses E-Nr./model revisions, so verify the complete model number including the suffix before ordering. Key Features Genuine Bosch OEM replacement part Includes terminal box and terminal block Connects household electrical power to dishwasher wiring Replaces Bosch part 640476 For select Bosch-built dishwasher platforms Cover 00640477 is sold separately Product Specifications Manufacturer Part Number 00640476 Manufacturer Bosch Part Type Dishwasher Terminal Box / Terminal Block Assembly Condition New Part Quality Genuine OEM Terminal Block Included Yes Cover Included No Matching Cover 00640477, sold separately Application Select Bosch-built dishwashers Installation Notes Shut off the dishwasher circuit breaker and verify power is off before beginning service. Remove the lower access panel as required for the model. Photograph and label existing wire connections before disconnecting them. Inspect supply wiring and the dishwasher harness for heat damage, burned insulation, or loose conductors. Transfer wiring to the new terminal block according to the dishwasher wiring diagram and installation instructions. Secure strain relief and wiring so no bare conductor is exposed. Install the proper terminal-box cover before restoring power. Electrical safety: This part carries household line voltage. If wiring is burned, melted, or damaged, correct the underlying connection problem and replace damaged wiring as required. Installation should be performed by a qualified person when local electrical codes or conditions require it. Frequently Asked Questions Is 00640476 a Genuine Bosch OEM part? Yes. It is manufactured by Bosch as an original equipment replacement terminal box. Does this include the terminal block? Yes. Bosch describes 00640476 as a terminal box with terminal block. Is the cover included? No. The matching wiring/terminal-box cover is Bosch part 00640477 and is sold separately. Does 00640476 replace 640476? Yes. 640476 is the earlier Bosch part number superseded by 00640476. Will it fit every Bosch dishwasher? No. Compatibility depends on the full Bosch E-Nr./model and revision. Verify the complete model number before purchase. Shop With Confidence Use the complete dishwasher model or E-Nr. to confirm fitment before ordering. Genuine Bosch OEM construction helps ensure the correct electrical connection design for compatible models. Genuine Bosch OEMTerminal Block IncludedCompatibility SupportNew Part

Read more less

XPARTCO W11175771 Dishwasher Water Valve Product Overview The XPARTCO W11175771 Dishwasher Water Valve controls the flow of water into your dishwasher during the fill cycle. This high-quality aftermarket inlet valve ensures the proper amount of water enters the unit, allowing for efficient and effective cleaning performance. Quick Answer If your dishwasher is not filling with water, filling too slowly, or not cleaning properly, the W11175771 water valve may be faulty. Replacing it restores proper water flow and washing performance. Replaces Part Numbers Replaces OEM part number: W11175771, W10195047, W10327250, W10872255, W11130744, EAP12578165, AWP43823, PD00052484, AP6339872, PS12578165, WPW10327249, W10327249, W10316814, 3015511, W11130743, PD00052484, EAP12578165, AP6019618, PS11752927. Compatibility This dishwasher water inlet valve is compatible with select Whirlpool, Maytag, KitchenAid, and other compatible dishwashers. Example compatible models include (but are not limited to): Whirlpool WDF520PADM7, WDT750SAKZ0 KitchenAid KDFE204KPS0 Maytag MDB4949SHZ0 Kenmore 665.13242K701 Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure. Common Problems This Part Fixes Dishwasher not filling with water Slow or weak water fill Dishes not cleaning properly Water flow issues during wash cycle Key Features Controls water intake during fill cycle Ensures proper water flow High-quality aftermarket replacement Durable and reliable construction Product Specifications Part Number: XPW11175771 Part Type: Dishwasher Water Inlet Valve Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Dishwasher Water Fill System Troubleshooting Guide No water entering → Faulty valve Slow fill → Clogged or weak valve Poor cleaning → Insufficient water supply When Should You Replace This Valve? Replace this valve if your dishwasher fails to fill with water, fills too slowly, or does not clean dishes effectively. Installation Notes ⚠️ Disconnect power and water supply before installation. Access the inlet valve from the bottom or rear of the unit and install securely according to your dishwasher model. Related Parts Dishwasher Float Switch Circulation Pump Drain Pump Frequently Asked Questions Will this valve fit my dishwasher?This valve fits many Whirlpool and compatible models. Always verify your model number. What does a water inlet valve do?It controls the amount of water entering the dishwasher. What are signs of a bad valve?No fill, slow fill, or poor cleaning performance. Is this OEM or aftermarket?This is a high-quality aftermarket replacement part. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support  

Read more less

WD08X27458 Dishwasher Genuine OEM Floating Seal – Compatible with GE Dishwashers Product Description Prevent leaks and ensure reliable dishwasher operation with the WD08X27458 Dishwasher Genuine OEM Floating Seal. This factory-approved seal fits beneath the float assembly, helping regulate water levels and keeping water contained inside the tub. A worn or damaged seal can cause leaks or improper filling. Replacing it with this genuine OEM part restores proper performance and protects your kitchen from water damage. Replaces Part Numbers WD08X27458, WD08X25471, AP7018540, EAP16554611, PD00072539, PS16554611. Compatibility This floating seal is compatible with select GE dishwashers. Example compatible models include (but are not limited to): GE GDF530PSM0SS, GE GDT695SMJ0ES, and GE PDT825SSJ0SS. Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Genuine OEM Part – Factory-approved floating seal for GE dishwashers 💧 Leak Protection – Keeps water contained in the dishwasher tub 💰 Cost-Effective Repair – Prevents costly kitchen water damage 🛠️ Easy Installation – Installs in minutes under the float assembly 🛡️ Fixes Common Issues – Resolves dishwasher leaks and incorrect filling 📐 Product Specification Part Number: WD08X27458 Component Type: Dishwasher Floating Seal Material: Durable rubber construction Mounting: Direct-fit replacement under float assembly Operating Conditions: Designed for residential dishwasher use Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: None or Phillips screwdriver (depending on model) ⚠️ Safety First: Disconnect power and water supply before servicing the dishwasher. Steps: Disconnect dishwasher from power and water supply. Open the dishwasher door and locate the float assembly. Lift float to access the old seal beneath it. Remove worn seal and place new WD08X27458 floating seal in position. Ensure secure fit, reinstall float, and close door. Restore power and water, then run a short cycle to test. ⏱️ Time Required: 10 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Stop leaks and protect your kitchen — Add to Cart Now for a genuine, factory-approved repair!

Read more less

WPW10605057 Genuine OEM Whirlpool Dishwasher Pump & Motor Assembly The WPW10605057 is a genuine Whirlpool OEM circulation pump and diverter motor assembly for Whirlpool, Kenmore, KitchenAid, Jenn-Air, Maytag, Amana, Magic Chef, Admiral, Norge, Roper, and Ikea dishwashers. This assembly pumps water up through the spray arms throughout the wash cycle, and the integrated diverter motor controls which spray arm receives that water at any given moment. This assembly includes the circulation pump and diverter motor only — it does not include the drain pump, which is a separate component on this platform. Over time, the pump motor's internal windings can wear out or fail electrically, or the diverter mechanism can stick or bind. A failing assembly typically shows up as a dishwasher that isn't washing dishes properly because water isn't circulating through the spray arms, or leaking from underneath the unit. Whirlpool's own guidance recommends checking the motor's resistance with a multimeter if water isn't circulating, to confirm the assembly before replacing it. It directly replaces AP6023350, WPW10482502, W10482502, W10605057, 3021439, 3023239, PS11756692, W10236194, W10534160N, W10300740, and W10500285. Quick Answer The WPW10605057 Genuine OEM Whirlpool Dishwasher Pump & Motor Assembly fixes Whirlpool, Kenmore, KitchenAid, Jenn-Air, Maytag, Amana, Magic Chef, Admiral, Norge, Roper, and Ikea dishwashers that aren't washing dishes properly because water isn't circulating, or that are leaking from underneath. Includes the circulation pump and diverter motor — not the drain pump. Replaces WPW10482502, W10482502, W10605057, 3023239, W10300740, W10500285, AP6023350, AWP51141, PD00026666, PS11756692. Check the motor's resistance with a multimeter before replacing to confirm this assembly is actually the cause. Common Problems This Part Fixes Dishes not getting clean because water isn't circulating through the spray arms Dishwasher leaking from underneath the unit Weak or absent water spray during the wash cycle Motor humming without spraying water normally Inconsistent washing results from cycle to cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher pump and motor assembly directly replaces the following OEM and cross-reference part numbers: WPW10605057, WPW10482502, W10482502, W10605057, 3023239, W10300740, W10500285, AP6023350, AWP51141, PD00026666, PS11756692. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This pump and motor assembly is compatible with select Whirlpool dishwashers, and also fits select Kenmore, KitchenAid, Jenn-Air, Maytag, Amana, Magic Chef, Admiral, Norge, Roper, and Ikea dishwashers built on the Whirlpool platform, including model numbers such as KDTE104ESS, WDT710PAHZ, KDFE104DSS, WDT780SAEM, and WDT710PAHB. Note — circulation pump only, not the drain pump: This assembly includes the circulation pump and diverter motor. The drain pump on this platform is a separate component and is not included with this assembly. If your dishwasher isn't draining rather than not washing properly, you likely need the drain pump instead. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which part your dishwasher needs. Key Features Genuine Whirlpool OEM part — factory-specified pump and diverter motor design Includes the circulation pump and diverter motor, which controls spray arm water flow Resolves "not washing properly," "water not circulating," and "leaking underneath" symptoms Factory Certified Part built to Whirlpool's engineering specifications Direct drop-in replacement — matches the original mounting and hose connections Replaces WPW10482502, W10482502, W10605057, 3023239, W10300740, W10500285, AP6023350, AWP51141, PD00026666, PS11756692 Compatible with Whirlpool, Kenmore, KitchenAid, Jenn-Air, Maytag, Amana, Magic Chef, Admiral, Norge, Roper, and Ikea dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance DIY-friendly repair, typically about 30 minutes Product Specifications Part Number WPW10605057 Part Type Dishwasher Circulation Pump & Diverter Motor Assembly Condition Genuine OEM Brand Whirlpool Function Circulates water through the spray arms; diverter motor controls spray arm flow Includes Drain Pump No — sold separately Repair Difficulty Moderate — approx. 30 minutes Quantity 1 pump and motor assembly Compatible Brands Whirlpool, Kenmore, KitchenAid, Jenn-Air, Maytag, Amana, Magic Chef, Admiral, Norge, Roper, Ikea Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Remove the lower dish rack, the impeller/spray arm, and the drain filter to access the interior floor of the tub. Working from underneath the dishwasher, release the drain hose from the pump using pliers, then hand-unscrew the drain pump and temperature sensor about a quarter-turn each, being careful to release the small clip holding the drain pump in place — leave both of these components in place, since they're not part of this replacement. Release the three levers that clamp the pump and motor assembly to the bottom of the dishwasher, positioned roughly at 0, 120, and 240 degrees around the assembly. Photograph the electrical connections before disconnecting anything, since keeping track of exactly how everything was wired makes reassembly straightforward. Pop the old assembly up and out through the bottom of the dishwasher. If your old assembly used a separate counterweight, transfer it to the new assembly. Install the new WPW10605057 assembly through the same opening, reconnect all electrical connections exactly as photographed, and re-engage the three clamping levers. Reconnect the drain pump, temperature sensor, and drain hose you set aside earlier. Reinstall the drain filter, spray arm/impeller, and lower rack. Restore water and power, then run a test cycle to confirm normal water circulation with no leaks underneath. Tools needed: multi-screwdriver, pliers, work gloves. Frequently Asked Questions My dishwasher isn't cleaning dishes well. How do I know if this is the right part? Whirlpool's own guidance recommends checking the pump motor's resistance with a multimeter first if water isn't circulating properly. If the motor tests outside its expected resistance range, or shows no continuity at all, that confirms this assembly has failed and needs replacing rather than a different component being at fault. Should I replace the drain pump at the same time? Not necessarily — this assembly doesn't include the drain pump, and if your dishwasher is washing normally but just not draining, the drain pump (a separate part) is the more likely cause rather than this circulation assembly. If both symptoms are present, it's worth checking both components, but they aren't sold together in this listing. Do I need to replace the counterweight or reuse the old one? If your dishwasher's original assembly used a separate counterweight component, transfer it from the old assembly to the new one during installation rather than assuming a new one is included. Check your specific model's parts diagram if you're not sure whether this applies to your dishwasher. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original pump design, diverter motor function, and mounting configuration of the circulation pump and motor assembly originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

DD62-00084A Dishwasher Genuine OEM Water Valve Description: This Water Valve is a Genuine OEM part compatible with specific Samsung dishwasher models. It is responsible for opening and closing the water supply to the dishwasher. It regulates the water pressure and ensures the proper amount of water is dispensed for each cycle.  Causes of a faulty water valve can include wear and tear over time, sediment or debris buildup, electrical component failure, or damage due to high water pressure. These factors can result in issues such as inadequate water flow, leaks, or the dishwasher not filling or draining properly. Replaces Part Numbers: DD62-00084A, AP5178218, PS4222448   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

🚰 DD82-01588A Dishwasher Water Inlet Valve – Genuine OEM Samsung Part 🔁 Replaces These Part Numbers DD82-01588A (primary OEM) Also Replaces PS12593084, AP6807545, DD81-02265A, AP6244375, PS12085633. Description: This Dishwasher Water Inlet Valve Assembly is essential for regulating the water flow into dishwasher, ensuring optimal cleaning performance. This replacement Genuine OEM part is engineered to provide precise water control, preventing leaks and maintaining efficient operation. ✅ Key Features Genuine Samsung OEM part – DD82-01588A Precision-engineered to match factory standards Controls cold water intake with accurate timing and pressure Easy to install using standard tools Tested for leak-free performance 🔧 Fixes Common Symptoms Dishwasher won’t fill or fills slowly Error codes related to water inlet No water intake at cycle start Valve leaks or hums without water flow 🚚 Why Buy from Parts‑O‑Matic? ✅ Genuine OEM quality — not a knock‑off ✅ Always Fast and Free U.S. shipping ✅ Expert customer support for part fitment ✅ Trusted by DIYers and appliance professionals 🛒 Restore proper water fill and cycle reliability — order your DD82-01588A OEM water inlet valve today from Parts‑O‑Matic and enjoy speedy, free delivery.

Read more less

W11434044 Genuine OEM Whirlpool Dishwasher Water Inlet Valve The W11434044 is a Genuine OEM Whirlpool replacement dishwasher water inlet valve assembly compatible with a wide range of Whirlpool, Maytag, KitchenAid, JennAir, Kenmore, Amana, Roper, Admiral, Estate, Crosley, Inglis, Ikea, Hardwick, Magic Chef, Norge, Modern Maid, and Caloric dishwashers. The water inlet valve is mounted at the base of the dishwasher and connects to the household cold water supply line. When the control board calls for water during the fill cycle, the valve's internal solenoid opens, allowing water to flow into the tub. The valve closes the instant the control board cuts power, stopping flow precisely when the correct water level is reached. Without a properly functioning inlet valve, the dishwasher can't get water into the tub — meaning it can't wash, rinse, or complete a cycle. Rated 120V AC, 50/60Hz, 6/5W. Approximate dimensions: 2.9" H x 2.3" W with a 0.9" threaded orifice for the water supply connection. The package includes the water inlet valve, water outlet pipe (inlet hose), and two hose clamps — everything needed for the connection between the valve and the dishwasher's water divider. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W11434044 directly replaces W11187724, W11025972, W11025970, AWP44732, AP6987233, and PS16217908. Important: the water inlet connection uses plastic threads, which are easily damaged by over-tightening or cross-threading — hand-tighten the water line carefully during installation. Installs in 30–45 minutes with basic hand tools. Quick Answer The W11434044 Genuine OEM Whirlpool Dishwasher Water Inlet Valve fixes Whirlpool, Maytag, KitchenAid, JennAir, and Kenmore dishwashers that aren't filling with water, fill slowly, aren't washing properly, drain immediately after filling, or leak at the valve. 120V AC, 50/60Hz, 6/5W. Approximately 2.9"H x 2.3"W. Genuine OEM. Includes inlet valve, water outlet pipe, and 2 hose clamps. Replaces W11187724, W11025972, W11025970, AWP44732, AP6987233, PS16217908. Compatible with WDT750SAKZ, KDTM404KPS, MDB4949SKZ, WDTA50SAKZ, KDTE204KPS, WDPA70SAMZ, WDPS7024, WDT740SAL, WDT751SAP, WDT970SAK series and related models. Plastic-thread inlet connection — hand-tighten carefully to avoid stripping. Common Problems This Part Fixes Dishwasher not filling with water — valve solenoid not opening when commanded Dishwasher filling too slowly — valve partially clogged with sediment or weak solenoid Dishes not being washed properly due to insufficient water fill Dishwasher fills but doesn't reach normal water level Water leaking from the valve body or its connections Dishwasher continuously running water even when the cycle should be complete — valve stuck open Dishwasher won't advance past the fill phase due to insufficient water detection Excessive cycle times as the dishwasher tries to fill from a partially clogged valve Multimeter test on the valve solenoid shows no continuity Replaces Part Numbers This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers: W11434044, W11025970, W11025972, W11187724, AP6987233, AWP44732, EAP16217908, PD00064823, PS16217908. W11434044 is the current OEM production part superseding W11187724, W11025972, and W11025970. Contact our support team with your model number if you need confirmation before ordering. Compatibility This water inlet valve is compatible with select dishwashers from the following brands: Whirlpool dishwashers — WDPA70SAMZ0, WDPA70SAMZ2, WDPA70SAMZ3, WDPS7024RV0, WDPS7024RZ0 series Whirlpool dishwashers — WDT740SALB2, WDT740SALB3, WDT740SALW2, WDT740SALW3, WDT740SALZ3 series Whirlpool dishwashers — WDT750SAKB0/B2/B3, WDT750SAKV0/V2/V3, WDT750SAKW0/W2/W3, WDT750SAKZ0/Z2/Z3 series Whirlpool dishwashers — WDT751SAPZ0, WDT751SAPZ1 series Whirlpool dishwashers — WDT970SAKV2, WDT970SAKV3, WDT970SAKZ2, WDT970SAKZ3 series Whirlpool dishwashers — WDTA50SAKB0/B2/B3, WDTA50SAKT0/T2/T3, WDTA50SAKV0/V2/V3, WDTA50SAKZ0/Z2/Z3 series KitchenAid dishwashers — KDTM404KPS, KDTE204KPS and related models Maytag dishwashers — MDB4949SKZ and related models JennAir, Kenmore, Amana, Roper, Admiral, Estate, Crosley, Inglis, Ikea, Hardwick, Magic Chef, Norge, Modern Maid, Caloric — select Whirlpool-built dishwashers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Controls the flow of water into the dishwasher during fill cycles Solenoid-actuated — opens precisely when the control board calls for water and closes the moment the call is dropped 120V AC, 50/60Hz, 6/5W — correct electrical specifications for compatible Whirlpool-platform dishwashers Dimensions: approximately 2.9" H x 2.3" W · 0.9" threaded orifice diameter Includes water inlet valve, water outlet pipe (inlet hose), and 2 hose clamps for a complete connection set Current OEM production part — supersedes W11187724, W11025972, and W11025970 Also replaces AWP44732, AP6987233, and PS16217908 Compatible with Whirlpool WDT740SAL, WDT750SAK, WDT751SAP, WDT970SAK, WDTA50SAK, WDPA70SAMZ, WDPS7024 series and select KitchenAid, JennAir, Kenmore, Maytag, Amana, Roper, Admiral, Estate, Crosley, Inglis, Ikea, and related Whirlpool-built dishwashers DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number W11434044 Supersedes W11187724, W11025972, W11025970 Part Type Dishwasher Water Inlet Valve Assembly Condition Genuine OEM Application Dishwashers (Whirlpool platform) Voltage 120V AC Frequency 50/60 Hz Wattage 6/5W Dimensions Approximately 2.9" H x 2.3" W Threaded Orifice Diameter 0.9" Inlet Thread Material Plastic (hand-tighten carefully to avoid stripping) Body Material ABS Plastic / Stainless Steel Includes 1x Inlet Valve, 1x Water Outlet Pipe, 2x Hose Clamps Compatible Brands Whirlpool, Maytag, KitchenAid, JennAir, Kenmore, Amana, Roper, Admiral, Estate, Crosley, Inglis, Ikea, Hardwick, Magic Chef, Norge, Modern Maid, Caloric Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Supply Before Starting — Wear Work Gloves — DON'T OVER-TIGHTEN PLASTIC THREADS Disconnect power at the breaker and shut off the household water supply at the shutoff valve under the sink before beginning. Wear work gloves and safety glasses to protect your hands and eyes. Have towels ready — residual water remains in the supply line and will spill when disconnected. Critical: the W11434044's water supply connection uses plastic threads. Multiple installers have reported stripping the plastic threads by over-tightening or cross-threading the water line during installation — always hand-tighten the fitting carefully and align the threads squarely before tightening. If your dishwasher is installed under a counter, working through the lower access panel is possible but tight — many installers find it easier to pull the dishwasher partially out from the cabinet, or lay it on its side, to reach the inlet connection cleanly (this also lets you use a 90-degree hose fitting without cross-threading). Remove the lower access panel (typically 2 screws) at the front bottom of the dishwasher. Locate the water inlet valve. Photograph the wire harness and hose connections before disconnecting anything. Disconnect the household water supply line from the valve. Squeeze the hose clamps with pliers and slide them back to release the outlet hose from the valve, then disconnect the wire harness plug. Remove the mounting screws holding the valve in place. Install the new W11434044 valve, secure the mounting hardware, and reconnect the outlet hose and hose clamps. Push the electrical connector's fixing plate firmly into place before connecting the wire harness plug — this prevents the connector from falling out during operation. Reconnect the household water supply — hand-tighten the fitting carefully to avoid stripping the plastic threads. Restore water and power. Run a test cycle and check for leaks at all connections. Tools needed: Phillips screwdriver, adjustable wrench (used lightly on plastic threads only!), channel-lock pliers, work gloves, safety glasses. Frequently Asked Questions My dishwasher isn't filling with water — is the inlet valve the problem? Very likely, yes — that's the most common symptom of a failed dishwasher water inlet valve. Before replacing, do a few quick checks: 1) confirm the household water supply to the dishwasher is turned on at the shutoff valve; 2) check the household water pressure at a nearby fixture (a nearby faucet) to make sure your home has normal pressure; 3) inspect the inlet screen on the valve for sediment buildup — a clogged screen can mimic a failed valve. If the supply is good and the screen is clean but the dishwasher still won't fill, the W11434044 valve solenoid has likely failed and replacing it will resolve the issue. You can also test the solenoid with a multimeter — no continuity means the solenoid has burned out. What is the difference between W11434044 and W11025970/W11025972/W11187724? These are the same water inlet valve across production revisions. W11025970 was the original OEM part number, W11025972 and W11187724 were mid-generation revisions, and W11434044 is the current OEM production version. All are physically and functionally interchangeable — if your dishwasher's parts diagram or the part on your appliance shows any of these numbers, the W11434044 is the correct current replacement, and this listing covers all of them. Why is over-tightening the water line connection such a common issue? The water supply inlet on the W11434044 has plastic threads to reduce cost and simplify manufacturing — but plastic threads are much less forgiving than brass or metal fittings. Cross-threading (starting the fitting at an angle instead of straight-in) or applying too much torque with a wrench will strip the plastic threads or split the fitting. Always align the water line fitting carefully by hand first, get several turns of engagement before applying any tool, and use only enough torque to snug the connection (typically hand-tight plus a very light quarter-turn with a wrench). If the threads are already stripped, the valve or a replacement plastic fitting will need to be ordered — the connection can't be repaired. Should I lay the dishwasher on its side for this repair? If you're finding it difficult to reach the water inlet connection cleanly through the lower access panel — which is a common complaint from installers — laying the dishwasher on its side (or pulling it partially out from the cabinet) makes the connection much easier to work with. This is especially helpful if your water supply line uses a 90-degree hose fitting that needs a straight approach for correct thread engagement. Before laying the dishwasher down, disconnect all connections and drain any residual water from the tub to avoid spills. Note that if the door has been damaged or bent, laying the unit on its side can worsen the damage — inspect first. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same water inlet valve installed in compatible Whirlpool, Maytag, KitchenAid, JennAir, Kenmore, Amana, and related Whirlpool-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less