Search results for "dryer Igniters and Gas Valves"

XPARTCO W11176454 Gas Range Oven Igniter The XPARTCO W11176454 is an aftermarket replacement oven burner igniter compatible with select Whirlpool, Maytag, and Amana gas ranges. The igniter is a hot surface igniter made from silicon carbide that draws electrical current through the oven safety valve to open it, then heats to ignition temperature to light the gas burner. When the igniter weakens or fails, the oven will not heat, will take too long to preheat, or the igniter will glow without lighting the burner. This igniter draws 3.3–3.6 amps at 120V AC and reaches operating temperatures of 1,800°F–3,100°F with a heating time of approximately 17 seconds. The igniter body measures 3-7/10 inches (Length A) with 9-1/2 inch leads and two separate connectors. It directly replaces OEM part numbers W11176454 and W10914411, and is compatible with Whirlpool WFG and WFG505 series, Amana AGR and AGG series, and select Maytag gas range models. Installs in 10–20 minutes with basic hand tools. Quick Answer The XPARTCO W11176454 Gas Range Oven Igniter fixes Whirlpool, Maytag, and Amana gas ovens that won't heat, take too long to preheat, or have an igniter that glows but never lights the burner. Silicon carbide construction. Draws 3.3–3.6A at 120V. Igniter body 3-7/10" with 9-1/2" leads and 2 separate connectors. Replaces W10914411. Common Problems This Part Fixes Oven not heating at all — gas is not igniting Oven takes excessively long to preheat (weak igniter not reaching ignition temperature) Igniter glows orange or red but never lights the gas burner Smell of gas when oven is turned on but burner does not light Oven heats inconsistently or shuts off mid-cycle Clicking sounds from the oven without successful ignition Oven element will not heat despite other components functioning normally Replaces Part Numbers This oven igniter directly replaces the following OEM and cross-reference part numbers: W11176454, 4547416, W10914411, EAP12348439, AWP43029, PD00044759, AP6327293, PS12348439. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This igniter is compatible with select gas ranges from the following brands: Whirlpool gas ranges — WFG320 and WFG505 series (freestanding) Amana gas ranges — AGR and AGG series Maytag gas ranges — select AGR series models Always verify your model number before ordering. Contact our support team if you're unsure. Key Features Hot surface igniter — draws current through the oven safety valve to open it, then ignites the gas burner Silicon carbide construction — superior heat resistance vs. standard ceramic igniters Draws 3.3–3.6 amps at 120V AC — correct range to open the Whirlpool gas safety valve Operating temperature: 1,800°F – 3,100°F with approximately 17-second heat-up time Igniter body length: 3-7/10 inches; lead length: 9-1/2 inches Two separate connectors for easy plug-in installation Directly replaces W11176454 and W10914411 — no modification required Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 10–20 minutes with a screwdriver Product Specifications Part Number W11176454 Also Replaces W10914411 Part Type Oven Burner Igniter (Hot Surface Igniter) Condition Aftermarket Replacement Application Gas Ranges and Ovens Material Silicon Carbide Amperage Draw 3.3 – 3.6 Amps Voltage 120V AC Resistance 40 – 800 Ohms Operating Temperature 1,800°F – 3,100°F Heat-Up Time Approximately 17 seconds Igniter Body Length (A) 3-7/10 inches Lead Length 9-1/2 inches Connectors 2 separate connectors Compatible Brands Whirlpool, Amana, Maytag Installation Notes ⚠️ Gas Appliance Safety Warning This part is used in gas ranges. Working with gas appliances carries risk of gas leaks, fire, and explosion if installed incorrectly. Always shut off the gas supply at the shutoff valve and unplug the range before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. If you are not confident working on gas appliances, have this part installed by a qualified appliance technician. ⚠️ Installation Instructions Unplug the range and shut off the gas supply before beginning. Open the oven door and remove the oven racks. Lift and remove the oven bottom panel by unscrewing the retaining screws. Remove the heat shield (if present) to expose the burner and igniter assembly. Unscrew the igniter mounting screws — typically one or two — and carefully disconnect the wire connector. Connect the new W11176454 igniter to the wire harness using the two separate connectors, secure it to the burner bracket with the mounting screws, then reinstall the heat shield and oven bottom panel. Restore gas supply and power and run a test cycle to confirm the oven lights correctly. Important: Do not touch the silicon carbide igniter element with bare hands — oils from skin reduce its lifespan. Handle only by the bracket and leads. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions What is the difference between W11176454 and W10914411? The W11176454 is the updated part number that directly supersedes the older W10914411. Both are the same hot surface igniter for compatible Whirlpool, Amana, and Maytag gas ranges. This aftermarket replacement is compatible with both part numbers. How do I know if my oven igniter needs to be replaced? The most common signs are the oven not heating at all, taking much longer than usual to preheat, or the igniter glowing orange but never lighting the burner. A working igniter reaches ignition temperature within about 30–90 seconds and glows bright orange. If it glows dimly or stays on indefinitely without the burner lighting, the igniter has weakened and is no longer drawing enough current to open the gas safety valve. Why does my igniter glow but the oven still won't heat? This is the classic symptom of a weak igniter. The gas safety valve requires a minimum amperage draw — typically around 3.2 amps — to open and allow gas to flow to the burner. As the igniter ages, its resistance increases and amperage drops below this threshold. The igniter still glows because it has some current, but not enough to open the valve. Replacing the igniter resolves this in nearly all cases. Is the W11176454 compatible with my Amana or Maytag range? Yes — the W11176454 is compatible with select Amana AGR and AGG series gas ranges and select Maytag AGR series models in addition to Whirlpool WFG320 and WFG505 series ranges. Always verify your specific model number before ordering to confirm compatibility. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is made from silicon carbide to match the electrical specifications and performance of the original W11176454 igniter. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO 53-1096 Gas Dryer Thermostat - Compatible with Maytag, Amana, Magic Chef, Jenn-Air Dryers Product Description Keep your gas dryer safe and operational with the replacement 53-1096 Gas Dryer Thermostat. This high-limit thermostat is designed for select Maytag, Amana, Magic Chef, and Jenn-Air gas dryers, preventing overheating by shutting off the burner at 240°F and restarting at 200°F. It addresses issues like no heat, overheating, or premature shutoff, offering a cost-effective alternative to OEM parts. Note: Includes one high-limit thermostat. Disconnect power and gas supply before installation. Often paired with thermal fuses (e.g., 53-1182, 53-0771) for comprehensive repairs. Replaces part numbers: WP53-1096, 53-1096, PD00055179, AP6009640, PS11742808. Compatibility: Compatible with models including but not limited to: Maytag: DG312, DG612, DG712, LDG7304AAL, LDG8604AAL, MDE3000AYW Amana: NGD7200TW10, 4GNED4400YQ2 Magic Chef: CYG1005AXX, CYG2000AWW Jenn-Air: JDE1000W, JDG1000W Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Maytag, Amana, Magic Chef, Jenn-Air, Norge, Admiral, and Crosley gas dryers. 🔥 Specifications: replacement high-limit thermostat, opens at 248°F, closes at 200°F, 25A at 240VAC. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, pliers, work gloves; typically installed in 15–20 minutes. 🛡️ Effective Fixes: Resolves no heat, overheating, or premature shutoff issues. Product Specification Part Number: 53-1096 Component Type: High-limit thermostat Material: Metal and plastic Mounting: Two 1/4" male spade terminals, includes mounting bracket Operating Conditions: Suitable for high-temperature gas dryer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source and gas supply before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a budget-friendly fix!

Read more less

UNIVRND Oven Genuine GE Universal Round Igniter Kit The UNIVRND is a genuine GE OEM universal round igniter kit for GE gas ranges and ovens. This is a high-temperature ignition component: when the burner is switched on, the igniter heats rapidly until it reaches the temperature needed to light the gas at the burner, allowing the flame to establish reliably each time the burner is used. Round in shape, with an 8" lead, rated 2.5 to 3.0 amps at 120V, and CSA approved. Made in the USA and backed by a 1-year warranty. This is a complete kit — beyond the igniter itself, it includes mounting hardware, a mounting bracket, installation instructions, and 2 porcelain high-temperature wire nuts. This is a universal replacement designed to fit a broad range of GE gas range and oven models. Over time, the igniter's element weakens or fails from repeated heating and cooling cycles. Symptoms of a failing igniter include a burner that won't light, ignition that's slow or inconsistent, or clicking without ignition. It directly replaces WB2X9154 and UNIVRND. Quick Answer The UNIVRND Oven Genuine GE Universal Round Igniter Kit fixes GE gas ranges and ovens with a burner that won't light, ignition that's slow or inconsistent, or clicking without ignition. Round shape, 8" lead, 2.5-3.0A/120V, CSA approved, Made in USA. Includes mounting hardware, bracket, and 2 porcelain high-temp wire nuts. Replaces WB2X9154, UNIVRND. Even though this is sold as a universal part, GE's own guidance notes that size and shape can have small variations between models that otherwise look similar — verify your part number carefully before ordering. Common Problems This Part Fixes Gas burner won't light Ignition that's slow or takes multiple attempts Clicking sound without the burner actually igniting Inconsistent or unreliable burner ignition Igniter glowing but failing to light the burner What's In The Kit 1x Universal Round Igniter, 8" lead Mounting hardware and bracket 2x Porcelain, high-temperature wire nuts Installation instructions Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers UNIVRND, EAP16728949, PS16728949, UNIVRND24PK, AGE1335580, AP7188082, PD00084791, WB2X9154, WB00X6640, 1990, 300259, 319887, 327617, 330689, 4336387, 4338008, AGE23042, AH243425, AP2014008, EAP243425, PD00001010, PS243425, Oven Round Igniter If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This is a universal igniter compatible with a broad range of GE gas ranges and ovens. Note: Per GE's own guidance, please verify your part number is correct for your model before ordering — parts may look the same but the size and shape can have small variations between models. Always confirm your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — complete igniter kit for GE gas ranges and ovens Resolves "won't light," "slow or inconsistent ignition," and "clicking without ignition" symptoms High-temperature ignition element heats quickly to light the burner Round shape, 8" lead Rated 2.5 to 3.0 amps, 120V CSA approved, Made in USA Includes mounting hardware, bracket, installation instructions, and 2 porcelain high-temp wire nuts Replaces UNIVRND, EAP16728949, PS16728949, UNIVRND24PK, AGE1335580, AP7188082, PD00084791, WB2X9154, WB00X6640, 1990, 300259, 319887, 327617, 330689, 4336387, 4338008, AGE23042, AH243425, AP2014008, EAP243425, PD00001010, PS243425, Oven Round Igniter Compatible with a broad range of GE gas range and oven models Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number UNIVRND Part Type Universal Round Oven/Range Igniter Kit Condition Genuine OEM Brand GE Shape Round Lead Length 8" Electrical Rating 2.5 to 3.0 Amps, 120V Certification CSA Approved Country of Origin Made in USA Kit Includes Igniter, mounting hardware, bracket, 2 porcelain high-temp wire nuts, instructions Application Gas Ranges and Ovens Repair Difficulty Moderate — gas appliance component Quantity 1 igniter kit Compatible Brand GE Installation Notes ⚠️ Gas Appliance — Turn Off Gas Supply And Power Before Starting This is a gas ignition component. Before beginning any work, unplug the range or shut off power at the breaker, and shut off the gas supply to the appliance at the shutoff valve. If you smell gas at any point during this repair, stop immediately, do not operate any switches, leave the area, and contact your gas utility or a qualified technician from a safe location. Access to the igniter typically requires removing the oven bottom panel or reaching behind the range's rear panel, depending on your model — consult your appliance's service documentation for the exact access point. Disconnect the wiring connector from the old igniter and remove the mounting screws securing it in place. Install the new UNIVRND using the included mounting bracket and hardware, securing it in the same position, and connect the wiring using the included porcelain high-temperature wire nuts rather than standard wire nuts, since ordinary ones aren't rated for the heat in this area. Restore the gas supply and power. Test the burner according to your appliance's normal operation, and confirm the igniter glows and the burner lights reliably. If you are not fully comfortable working with gas line connections, have a qualified technician perform this repair instead. ⚠️ WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer and reproductive harm. For more information, visit P65Warnings.ca.gov. Frequently Asked Questions Does this include everything I need to install it, or just the igniter itself? This is a complete kit — it includes the igniter, mounting hardware, a mounting bracket, installation instructions, and 2 porcelain, high-temperature wire nuts. Use the included porcelain wire nuts rather than standard ones when making the wiring connection, since this area gets hot enough that ordinary wire nuts aren't rated for it. My burner won't light. Is this the part I need? Yes, this is the most direct symptom of a failed igniter. Since this component is what heats up to light the gas at the burner, a weakened or failed igniter element can prevent the burner from lighting at all, or cause slow, inconsistent ignition. If this is a "universal" part, do I still need to check compatibility? Yes. Even though this igniter is designed to fit a broad range of GE gas range and oven models, GE's own guidance specifically notes that similar-looking igniters can have small variations in size and shape between models. Confirm your part number and model before ordering to avoid a mismatch. Is this safe to install myself? This involves working near a gas appliance's ignition system, so extra care is warranted. Always shut off the gas supply and power before starting, and if you're not comfortable working with gas connections or you smell gas at any point, stop and have a qualified technician complete the repair instead. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original ignition element design, lead length, and mounting configuration of the igniter it's designed to replace. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 8573713 Gas Dryer Thermal Cut-Off Fuse Replaces WP8573713 The XPARTCO 8573713 is an aftermarket replacement thermal cut-off fuse for Whirlpool, Maytag, Kenmore, Crosley, Amana, and Inglis gas dryers. This fuse is mounted on top of the burner funnel, directly under the drum, and it's a one-time safety device: as long as the dryer stays within its normal operating temperature, it does nothing at all, but the instant temperatures near the burner climb high enough — almost always from restricted airflow — the fuse permanently opens the circuit and cuts power. That's why a blown fuse produces such a specific symptom: the dryer won't heat, even though the drum may still tumble and the rest of the dryer seems to run normally. Because this fuse sits on the burner funnel underneath the drum rather than on the more accessible blower housing, replacing it is a more involved repair than a typical thermal fuse swap — the drum has to come out of the cabinet to reach it. Unlike a resettable thermostat, this fuse cannot be reset once it blows; it must be replaced. A blown thermal fuse is almost always a symptom rather than a random failure: restricted exhaust venting is the leading cause, since trapped heat near the burner is exactly what this fuse is designed to react to. It directly replaces WP8573713, AP6013467, and PS11746693. Quick Answer The XPARTCO 8573713 Gas Dryer Thermal Cut-Off Fuse fixes Whirlpool, Maytag, Kenmore, Crosley, Amana, and Inglis gas dryers that won't heat, even if the drum still tumbles normally. Mounted on the burner funnel under the drum. Replaces WP8573713, AP6013467, PS11746693. Always inspect and clean the dryer venting when replacing this fuse — a blown fuse is a symptom of restricted airflow, and installing a new fuse without fixing the vent will likely blow it again. Common Problems This Part Fixes Dryer runs and tumbles but produces no heat Dryer that stopped heating suddenly, especially after running unusually hot Drying times that have gotten noticeably longer or clothes coming out damp Repeated blown fuses on a dryer with a known venting or airflow restriction Dryer that recently smelled like burning or overheating before losing heat Continuity test shows an open circuit across the old fuse Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This gas dryer thermal cut-off fuse directly replaces the following OEM and cross-reference part numbers: WP8573713, 1180872, 8573713, AP3866211, EAP990558, PS990558, AWP49233, PD00006618 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal cut-off fuse is compatible with select Whirlpool gas dryers, and also fits select Maytag, Kenmore, Kenmore Elite, Crosley, Amana, Inglis, and Sears Canada gas dryers built on the Whirlpool platform, including model numbers such as WGD8500SR0, and Kenmore 11070372710 and 11071112020. Note: This fuse is specific to gas dryers, mounted on the burner funnel. It is not the same fuse used on electric dryer platforms. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement thermal cut-off fuse — one-time safety device that cuts power if the dryer overheats Mounted on top of the burner funnel, directly under the drum Resolves "runs but won't heat," "drying takes too long," and "clothes coming out damp" symptoms caused by a blown fuse Replaces WP8573713, AP6013467, and PS11746693 Compatible with Whirlpool, Maytag, Kenmore, Kenmore Elite, Crosley, Amana, Inglis, and Sears Canada gas dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 8573713 OEM Part Number WP8573713 Part Type Gas Dryer Thermal Cut-Off Fuse Condition Aftermarket Replacement Application Gas Dryers Location Top of the burner funnel, under the drum Resettable No — one-time use, must be replaced once blown Material Plastic housing Dimensions Approx. 1"H x 1"W Repair Difficulty Moderate to Hard — drum removal required for access Quantity 1 thermal cut-off fuse Compatible Brands Whirlpool, Maytag, Kenmore, Kenmore Elite, Crosley, Amana, Inglis, Sears Canada Installation Notes ⚠️ Gas Safety — Shut Off The Gas Supply Before Starting This fuse sits directly on the burner funnel, close to the gas burner assembly. Before beginning, close the gas shutoff valve behind the dryer in addition to unplugging the dryer or shutting off its circuit breaker. If at any point you smell gas, stop immediately, leave the area, and do not operate any switches — contact your gas utility or a qualified technician. Do not attempt this repair if you are not comfortable working safely around a gas appliance's burner assembly; a qualified technician can complete it instead. ⚠️ Drum Removal Required — Inspect And Clean The Venting Before Reassembling Wear work gloves. This repair requires removing the drum from the dryer cabinet to access the burner funnel, so budget more time and disassembly than a typical thermal fuse swap. Remove the top and front panels according to your model's service diagram, disconnect the drive belt from the idler pulley, and lift the drum out of the cabinet to expose the burner funnel underneath. Photograph the wiring before disconnecting the old fuse's connectors. Test the old fuse for continuity with a multimeter to confirm it's actually blown (no continuity) rather than assuming, and test the new fuse to confirm it's good out of the box. This is the most important step: fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. A blown thermal fuse is a symptom of restricted airflow, and skipping this step means the new fuse is likely to blow again. Install the new 8573713 fuse on the burner funnel in the same mounting position, reconnect the wiring, and reassemble the drum, belt, and panels in reverse order. Restore the gas supply and power, and run a test cycle to confirm normal heating and shutoff behavior. Tools needed: Phillips or nut driver (model-dependent), multimeter, vent brush or vacuum attachment for cleaning ductwork, work gloves. Frequently Asked Questions My dryer tumbles fine but there's no heat. Is this the right part? Yes, this is the classic symptom of a blown gas dryer thermal cut-off fuse. Because this fuse only interrupts the heating circuit and not the drive motor, the drum can continue tumbling completely normally while the dryer produces no heat at all. If you've confirmed the burner isn't igniting and the fuse tests as an open circuit, this is very likely the fix. Why does this repair require removing the drum? My other dryer's fuse didn't need that. This particular fuse is mounted on the burner funnel underneath the drum rather than on the blower housing at the back of the cabinet, which is where many thermal fuses on other platforms are located. Reaching the burner funnel requires taking the drum out of the cabinet, which is why this repair involves more disassembly than some other thermal fuse replacements. I replaced the fuse and it blew again. What's going on? This is a strong sign that the underlying cause — almost always restricted airflow — was never addressed. Thermal fuses don't fail from age; they blow because the dryer overheated. If a new fuse keeps blowing, thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications and mounting configuration of the original WP8573713 thermal cut-off fuse used in compatible Whirlpool, Maytag, Kenmore, Crosley, Amana, and Inglis gas dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO EXP570 Dryer Door Latch Kit The XPARTCO EXP570 is an aftermarket replacement door catch and strike kit for dryers from Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis, LG, and other comparable brands. The catch and strike work as a pair: the strike on the dryer door engages the catch on the cabinet to hold the door shut for the whole cycle. When either part wears, cracks, or gets knocked out of alignment, the door stops latching reliably. It may not stay closed, it may pop open mid-cycle and let heat escape, or the dryer may refuse to start because it doesn't register the door as closed. Each kit includes 1 door catch and 1 strike, so you can replace the full latch set in one repair rather than guessing which half is worn. Because this latch design was used across several appliance families, the kit carries a long cross-reference list covering Whirlpool, Frigidaire, GE, LG, and Alliance-built part numbers; see the Replaces list below. Quick Answer The XPARTCO EXP570 Dryer Door Latch Kit fixes a dryer door that won't stay closed, opens mid-cycle, or an open-door condition that keeps the dryer from starting, caused by a worn or damaged catch and strike. Each kit includes 1 door catch and 1 strike. Fits Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis, and LG dryers. Classic symptom: the door swings open on its own, or you have to hold it shut to get the dryer to run. Common Problems This Part Fixes Dryer door won't stay closed Door pops open in the middle of a cycle Dryer won't start because the open-door condition isn't clearing Worn, cracked, or damaged catch or strike Heat escaping around the door, leaving clothes damp Door that no longer latches with a firm, positive click Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door latch kit directly replaces the following part numbers: 5366021400, 5303207102, AP2153772, PS475419, AP2137890, PS455020, LA-1003, LA1003, PS2162263, AP4242465, WE1M1011, WE1X1192, WE1M536, WE1X1195, WE01X1158, WE01X10023, WE01X10188, WE01X10184, AP5324728, PS3502777, AP2042206, PS266893, AP5324728, PS3502777, AP2042209, PS266896, AP2042175, PS266861, AP2042031, PS264343, AP3775568, PS959860, AP5238145, PS959856, WE1X1194, PS266895, AP2042208, WE1M1011, WE1X1192, WE1M536, WE1X1195, WE01X1158, WE01X10023, WE01X10188, WE01X10184, AP5324728, PS3502777, AP2042206, PS266893, AP5324728, PS3502777, AP2042209, PS266896, AP2042175, PS266861, AP2042031, PS264343, AP3775568, PS959860, AP5238145, PS959856, 4027EL2001A, 4026EL3001A, PS3522845, AP5238145, AP5242421, PS3522822, 00491624, AP3735937, PS959856, 5366021400, 5303207102, AP2153772, PS475419, AP2137890, PS455020, 279570. This latch kit was sold under the part numbers of several manufacturers: Whirlpool and Maytag (279570), Frigidaire and Electrolux (5303207102), GE (WE01X10023 and related), LG (4027EL2001A, 4026EL3001A), and Alliance-built dryers (LA-1003). The AP/PS-prefixed numbers are third-party catalog cross-references for the same physical parts. Compatibility This latch kit is used on dryer models from the following brands: Whirlpool, Kenmore (Whirlpool-built), Maytag, Amana, Roper, Estate, and Inglis dryers Frigidaire, Electrolux, and Kenmore (Frigidaire-built) dryers GE and Hotpoint dryers Select LG and Kenmore (LG-built) dryers Select Crosley, Norge, and Speed Queen dryers Note: This kit fits specific models within each brand, not every dryer a brand has made, and the latch design differs between manufacturers. Match the number on your old catch and strike, or on your dryer's parts diagram, against the Replaces list above rather than relying on brand alone. Contact our support team with your model number and we'll verify fit before you order. If only the catch needs replacing, see our single EXP571 Dryer Door Catch. Key Features Aftermarket replacement dryer door latch kit with 1 door catch and 1 strike Replaces both halves of the latch in one repair Restores a secure door closure so heat stays in and the dryer runs efficiently Resolves doors that won't stay shut, open mid-cycle, or trigger an open-door no-start Cross-references to Whirlpool, Frigidaire, GE, LG, and Alliance OEM numbering 1 kit per order Product Specifications Part Number EXP570 OEM Part Number 279570, 5303207102, WE01X10023, 4027EL2001A Part Type Dryer Door Latch Kit (Door Catch & Strike) Condition Aftermarket Replacement Kit Contents 1 Door Catch & 1 Strike Quantity 1 Kit Application Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis & LG Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Open the door and inspect the old catch on the cabinet and the strike on the door for cracks, wear, or loose mounting. Remove the old catch and strike, keeping track of how each one is oriented and mounted. Fit the new catch and strike in the same positions and fasten them securely. Close the door and confirm it latches with a firm click, stays shut, and lines up evenly with the cabinet. If the door still won't seat properly after the swap, check the door hinges and alignment, since a misaligned door can wear out new latch parts quickly. Frequently Asked Questions My dryer door won't stay shut — is this the part I need? Very likely. A worn or damaged catch or strike is a common reason a dryer door won't latch or pops open mid-cycle. Inspect both parts for cracks or wear. Because the two work as a pair, replacing both at once is the surest fix. My dryer won't start and seems to think the door is open. Could this be the cause? It can be. If the door isn't latching fully, the dryer may not register it as closed. If the latch looks fine and the door closes firmly but the dryer still won't start, the door switch may be the problem instead. What's included in the kit? Each kit includes 1 door catch and 1 strike. If you only need the catch, we also offer it separately as the EXP571 Dryer Door Catch. Will this fit my Whirlpool, Frigidaire, GE, or LG dryer? This kit is cross-referenced to part numbers from all of those brands, but it fits specific models rather than every dryer. Match the number on your old latch parts or parts diagram against the Replaces list, or contact our support team with your model number and we'll confirm before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 279838 Dryer Heating Element The XPARTCO 279838 is an aftermarket replacement heating element for Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, Inglis, KitchenAid, and Jenn-Air electric dryers. This element is the source of virtually all the heat in the dryer: current flows through a nickel-chromium coil, which glows and radiates heat as the blower pushes air across it and into the drum. This part is often nicknamed the "shorty" because of its compact size compared to the larger, older Whirlpool element it replaced, part number 4391960 — the shorty design is used on dryers with the lint filter positioned on the top right near the control housing. Over years of use, the coil typically fails with a visible break somewhere along its length — a section simply burns through and the circuit opens, cutting off heat entirely. A quick way to check: a healthy element reads approximately 9 to 10 ohms across its terminals with a multimeter; a reading of no resistance (open circuit) confirms the element has failed. This element shares the same dryer platform as our WP3392519 thermal fuse and works alongside a cycling thermostat and high-limit thermostat in the same heating circuit — all commonly checked or replaced together when a dryer stops heating. It directly replaces 279837, WP279837, 2438, 279838VP, 279838A, 3398063, 3398064, 3403585, 8565582, W10724237, AP3094254, AH334313, EA334313, PS334313, and PS3343130. Quick Answer The XPARTCO 279838 Dryer Heating Element fixes Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, Inglis, KitchenAid, and Jenn-Air electric dryers with no heat, insufficient heat, or drying times that have gotten noticeably longer. Also called the "shorty" element. Replaces 279837, WP279837, 2438, 279838VP, 279838A, 3398063, 3398064, 3403585, 8565582, W10724237, AP3094254, AH334313, EA334313, PS334313, PS3343130. A healthy element reads approximately 9-10 ohms with a multimeter; if the dryer has no heat at all, also check the thermal fuse (such as our WP3392519 listing) before assuming the element is at fault — a blown fuse produces the identical symptom. Common Problems This Part Fixes Dryer runs a full cycle but produces no heat at all Dryer produces some heat, but not enough to dry clothes properly Drying times that have gotten noticeably longer than they used to Clothes coming out cold or barely warm at the end of a cycle Visible break or burned-through section in the heating coil Element that reads no resistance (open circuit) on a multimeter continuity or ohms test Dryer that heats inconsistently, cycling on and off unexpectedly Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer heating element directly replaces the following OEM and cross-reference part numbers: 279838, WP279837, 279837, 2438, 279838A, 279838VP, 3398063, 3398064, 3403585, 8565582, W10724237, AH334313, AP3094254, AWP39215, PD00002351, EA334313, OEM9282771, PS334313. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This heating element is compatible with select Whirlpool electric dryers, and also fits select Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, Inglis, KitchenAid, and Jenn-Air dryers built on the same platform, including model numbers such as: LER5624DQ0, LER4634EQ2 NED4655EW, NED4600YQ1 WED4815EW, WED4800BQ1, WED49STBW1, WED8300SW0 MEDC465HW, MEDC215EW, MEDX655DW, MEDX655DW1 RED4640YQ1, AED4675YQ1, AED4475TQ1 EED4400WQ0 Kenmore 70, 80, 90, 300, 400, 500, and 600 Series Model 110 Note: This element fits Whirlpool-platform dryers with the lint filter positioned on the top right near the control housing. It is a compact "shorty" design and is not the same element as the larger, older 4391960 used on earlier Whirlpool dryers. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement heating element — generates the heat that dries clothes Resolves "no heat," "insufficient heat," and "drying takes too long" symptoms caused by a burned-through coil Nickel-chromium coil for effective, heat-and-abrasion-resistant heating Compact "shorty" design for dryers with the lint filter near the control housing Direct drop-in replacement — no modification required Replaces 279837, WP279837, 2438, 279838VP, 279838A, 3398063, 3398064, 3403585, 8565582, W10724237, AP3094254, AH334313, EA334313, PS334313, and PS3343130 Compatible with Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, Inglis, KitchenAid, and Jenn-Air electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XP279838 OEM Part Number 279838 Part Type Dryer Heating Element Assembly ("Shorty") Condition Aftermarket Replacement Coil Material Nickel-chromium Typical Resistance (Healthy Element) Approx. 9-10 ohms Legacy Predecessor 4391960 (larger, older design, not interchangeable) Related Components Cycling thermostat, high-limit thermostat, thermal fuse (see our WP3392519 listing) Repair Difficulty Medium — basic electrical skills and dryer panel disassembly required Quantity 1 heating element assembly Compatible Brands Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, Inglis, KitchenAid, Jenn-Air Installation Notes ⚠️ Unplug Dryer Before Starting — Test Resistance Before Assuming It's The Element Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel or the front, depending on your model, to reach the heater duct/blower housing area where the element is mounted. Before removing anything, inspect the old element visually for a break in the coil — sometimes you can see it directly, or feel it by gently wiggling each section of the coil. If nothing is visibly broken, test with a multimeter: place one probe on each terminal and look for a reading of approximately 9-10 ohms on a good element; no resistance at all confirms the element has failed. Photograph the wiring before disconnecting anything. Disconnect the wire terminals from the old element, remove the mounting screws or clips holding it in the duct housing, and pull it free. Install the new 279838 assembly in the same position, reconnect the wire terminals, and secure the mounting hardware — if the original connection wire shows burning or damage, replace it as well rather than reusing a damaged connector. Reassemble the panel, restore power, and run a test cycle to confirm the dryer is heating normally. Tools needed: 1/4" nut driver, 5/16" wrench, Phillips screwdriver, multimeter, work gloves. Frequently Asked Questions How do I test whether the element is actually bad? Start with a visual inspection — often you can see a break directly in the coil, or find it by gently wiggling each section to check for a loose or separated point. If nothing is visible, use a multimeter set to ohms and place one probe on each terminal. A good element typically reads approximately 9 to 10 ohms; a reading of no resistance at all (open circuit) confirms the element has failed and needs replacing. My dryer has no heat at all. Should I replace the element first, or check something else? Check the thermal fuse first, since a blown fuse produces the exact same "no heat at all" symptom as a failed heating element and is a cheaper, faster part to test and replace — our WP3392519 listing covers the thermal fuse used on this same dryer platform. If the fuse tests good and the dryer still has no heat, the element itself is the next thing to test. What's the difference between this "shorty" element and the older 4391960? Both are Whirlpool dryer heating elements, but this 279838 is a more compact design used on dryers with the lint filter positioned on the top right near the control housing, while 4391960 is the larger, older element used on earlier Whirlpool dryer platforms. They are not interchangeable, so confirm which style your dryer uses — checking your model number or comparing the physical size of your old element — before ordering. Should I check the connection wire while I'm replacing the element? Yes, it's worth a look. The wire connecting to the element terminals can occasionally show burning or damage if the element was arcing or overheating before it failed. If you notice any discoloration, melting, or damage on the connection wire, replace it along with the element rather than reusing a compromised connector. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the nickel-chromium coil composition, resistance rating, compact "shorty" form factor, and terminal configuration of the original 279838 heating element used in compatible Whirlpool, Kenmore, Maytag, Amana, Roper, and related dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC47-00019A Dryer Heating Element Replaces WP35001247 The XPARTCO DC47-00019A is an aftermarket replacement universal-fit dryer heating element compatible with a wide range of electric dryers across multiple manufacturers — including Samsung, Whirlpool, Maytag, Amana, Inglis, and Kenmore. The heating element generates the heat that warms the air circulating through the dryer drum, evaporating moisture from wet clothes during each drying cycle. When the element fails, the dryer continues to tumble normally but produces no heat, leaving clothes damp at the end of a complete cycle. This replacement element comes pre-assembled with insulators and restring already attached, allowing for fast installation. Rated 240V, 5300W, with metal and ceramic construction. Overall dimensions are approximately 17"L x 6-1/2"W x 2-1/2"H. Important: this is a heating element assembly only — you must reuse the housing/cannister from your old element when installing the new one. It directly replaces DC47-00019A, 35001247, WP35001247, WP35001247VP, TJDC47-00019A, DE0019A, ERDC47-00019A, 35001119, 2068550, 1185561, AP4045884, AP4201899, AP6008695, AH2038533, EA2038533, EAP2038533, EAP11741835, PD00001991, PD00002996, PS2038533, PS4205218, and PS11741835. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO DC47-00019A Dryer Heating Element fixes Samsung, Whirlpool, Maytag, Amana, Inglis, and Kenmore electric dryers that tumble normally but produce no heat or take much longer than usual to dry. Universal-fit element — 240V, 5300W. 17"L x 6-1/2"W x 2-1/2"H. Insulators and restring pre-attached. Must reuse the housing/cannister from the old element. Replaces DC47-00019A, 35001247, WP35001247, WP35001247VP, TJDC47-00019A, DE0019A, ERDC47-00019A, 35001119, 2068550, 1185561, AP4045884, AP4201899, AP6008695, PS2038533, PS4205218, PS11741835. Common Problems This Part Fixes Dryer tumbles normally but produces no heat — element coil burned through Dryer takes significantly longer than usual to dry a load Clothes coming out damp or only partially dried at the end of a cycle Visible breakage in the element coil — snapped or burned-through Ni-Cr wire Dryer trips the circuit breaker when the heat setting is selected — shorted element Burning smell during operation — element arcing at a weak point in the coil Multimeter continuity test on the element shows an open circuit Replaces Part Numbers This dryer heating element directly replaces the following OEM and cross-reference part numbers across multiple brands: DC47-00019A, 2068550, AP4201899, ASM33630, AP2038533, DE0019A, ERDC47-00019A, PD00001991, PS4205218, TJDC47-00019A, WP35001247, 35001247, 1185561, AP6008695, AWP47390, EAP11741835, PD00002996, PS11741835, WP35001247VP. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This universal-fit heating element is compatible with select electric dryers from multiple manufacturers: Samsung electric dryers — DV2, DV3, DV4, DV5, DVE series (DV40J3000EW, DV42H5000EW, DV42H5200EW, DV42H5600EP, DV45H7000EW, DV48H7400EW, DV50F9A7EVW, DV50F9A7EVP, DVE50M7450W, DVE50R5200W, DVE50R5400V, DV203AEW, DV206LEW, DV209AEW, DV210AEW, DV419AEU, DV448AEE, DV448AEP, DV5471AEW and many related models) Whirlpool electric dryers (select models — see WP35001247 cross-reference) Maytag electric dryers (MDE6700AYW, MDE6700AZW, MDG6700AWM, MDG6700AWW and related) Amana electric dryers (NED7200TW10, YIED7200TW10 and related) Inglis electric dryers (select models) Kenmore / Sears electric dryers (Samsung and Whirlpool-built — select models) Important — Reuse Existing Housing: This listing is for the heating element assembly only — the metal housing/cannister that the element sits inside is not included. You must reuse the housing from your old element. Remove the old element from its housing, then install the new DC47-00019A element into that same housing before reinstalling in the dryer. Also: this part is for electric dryers only — gas dryer models use different components. Always verify your specific model number before ordering. Key Features Universal-fit replacement heating element for multiple dryer manufacturers — replaces both Samsung DC47-00019A and Whirlpool/Maytag WP35001247 part numbers Generates the heat that warms drying air — essential for the dryer to actually dry clothes Pre-strung Ni-Cr (nickel-chromium) heating wire — high heat conductivity and resistance to warping over time Insulators and restring already attached — ready for installation into the existing housing Rated 240V, 5300W — correct electrical specifications for compatible electric dryers Dimensions: 17"L x 6-1/2"W x 2-1/2"H Metal and ceramic construction — durable for repeated heat/cool cycles Electric dryers only — NOT compatible with gas dryer models Important: heating element assembly only — must reuse the housing/cannister from the old element Replaces 22+ OEM and cross-reference part numbers across Samsung, Whirlpool, Maytag, Amana, and related brands Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number XPDC47-00019A Also Replaces (Whirlpool-side) WP35001247, 35001247 Part Type Dryer Heating Element Assembly (Universal Fit) Condition Aftermarket Replacement Application Electric Dryers Only (NOT gas) Voltage 240V AC Wattage 5300W Terminal Connections 2 spade terminals Dimensions 17"L x 6-1/2"W x 2-1/2"H Material Metal / Ceramic / Ni-Cr coil wire Includes Heating element assembly with insulators and restring pre-attached (housing NOT included — reuse old) Compatible Brands Samsung, Whirlpool, Maytag, Amana, Inglis, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Do Not Touch the Element with Bare Hands Disconnect power before beginning. Wear work gloves throughout — there are sharp sheet metal edges inside the dryer cabinet. The new heating element coil is sensitive to skin oils, which can cause premature burnout — handle the element only by the metal frame, not the coil wire. Remove the rear panel of the dryer to access the heating element housing/cannister. Take a photo of all wire connections and the orientation of the element before disconnecting anything. Disconnect the wires from the old element terminals and remove the housing from the dryer. With the housing on a workbench, remove the old element from inside the housing — note exactly how it sits and how the restring is positioned. Install the new DC47-00019A element into the same housing, following the same orientation as the old element. Do not let the Ni-Cr heating wire touch the housing during installation — this can cause arcing and immediate burnout. Reinstall the housing in the dryer, reconnect all wires snugly to the correct terminals, and reinstall the rear panel. Restore power and run a test heat cycle to confirm the dryer is heating properly. While the rear panel is open, inspect the high-limit thermostat, thermal fuse, and thermistor — if the element failed due to overheating, these may also be stressed. Tools needed: Phillips screwdriver, 1/4" nut driver, work gloves. Frequently Asked Questions Does this really fit both Samsung AND Whirlpool dryers? Yes — this is one of the more unusual cases in dryer parts where an aftermarket heating element has been designed to serve as a direct replacement for both the Samsung DC47-00019A and the Whirlpool/Maytag WP35001247 (35001247) elements. The two OEM elements share the same physical dimensions, electrical specifications (240V, 5300W), and terminal configuration, allowing a single aftermarket element to function correctly in both platforms. Compatible models span Samsung's DV series, Whirlpool/Maytag's affected dryers (MDE6700/MDG6700 and similar), and select Amana, Inglis, and Kenmore Whirlpool-built or Samsung-built models. Always verify your specific model number before ordering. Why do I need to reuse the housing from the old element? This listing is for the heating element assembly only — the metal cannister or housing that contains the element is not included. The housing is a heavy gauge metal enclosure with mounting brackets that secure it to the dryer cabinet, along with airflow ducting that directs air across the heating coil. Reusing the housing keeps the cost down and is standard practice for this type of replacement. Carefully remove the old element from the housing, install the new element in its place, and then reinstall the housing in the dryer. If your housing is damaged or burned through, it will need to be replaced separately. How do I know if the heating element has failed? The clearest sign is a dryer that tumbles and runs through a complete cycle normally but produces little or no heat, leaving clothes damp at the end. You may also notice the dryer taking much longer than usual to dry a load as it tries to compensate. Visually inspecting the element after removing the rear panel can reveal burn marks, breaks in the coil, or visible arcing damage. A multimeter continuity test on the disconnected element will also confirm failure — a working element shows continuity, while a failed element reads an open circuit (no continuity). Should I replace the thermal fuse and thermostats at the same time? It's a good idea to inspect them. When a heating element fails — especially if it failed due to overheating rather than simple end-of-life wear — the paired thermal fuse, high-limit thermostat, and thermistor located in the same area can also be stressed by the heat event. Since the rear panel must already be open to replace the element, checking these components' continuity with a multimeter is a quick step that can prevent a repeat repair if any of them are also on the verge of failing. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung or Whirlpool OEM part, but is manufactured to match the electrical specifications (240V, 5300W), dimensions, and Ni-Cr coil construction of the original DC47-00019A and WP35001247 heating elements that it replaces. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10209656 Range Surface Igniter – Compatible with Whirlpool, Maytag, KitchenAid, and Kenmore Gas Ranges Product Description Restore reliable burner ignition with the XPARTCO W10209656 Range Surface Igniter. This high-quality aftermarket replacement provides the heat needed to ignite gas burners on your cooktop. A weak or failed igniter can cause burners not to light or take too long to ignite. Replacing it with this durable XPARTCO igniter restores instant ignition and safe cooking performance. Replaces Part Numbers WPW10209656, W10209656, 1468965, 98008959, 98012193, 98014514, 98014515, 98017561, 98017562, 98017917, W10112313, W10127479, AP6017135, PS11750430. Compatibility This replacement surface igniter is compatible with select Whirlpool, Maytag, KitchenAid, and Kenmore gas ranges. Example compatible models include (but are not limited to): Whirlpool WFG320M0BS3, Maytag MGR6600FZ0, and Kenmore 665.75002100. Always verify your range’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Compatible with Whirlpool-brand gas ranges 🔥 Reliable Ignition – Provides consistent spark for fast burner lighting 💰 Affordable Solution – Quality alternative to OEM parts at lower cost 🛠️ DIY Friendly – Installs easily with basic hand tools 🛡️ Fixes Common Issues – Solves burners not igniting or clicking without flame 📐 Product Specification Part Number: W10209656 Component Type: Gas Range Surface Igniter Material: High-temperature ceramic base and metal electrode Mounting: Direct-fit replacement for surface burner assembly Operating Conditions: Designed for standard household gas ranges Compliance: Built to OEM-equivalent standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the range and shut off the gas supply before starting repairs. Steps: Disconnect power and shut off gas supply. Remove burner grates and top panel to access the igniter. Detach the wire connector and mounting screw from the old igniter. Install the new XPARTCO W10209656 igniter and reconnect wires. Reassemble burner components, restore power and gas, and test ignition. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Enjoy quick, reliable ignition every time — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

ERP IG5068 Gas Oven Igniter Replaces Part Numbers: 5303935068, 316119302, 08067970, 12874, 316T023P03, 316T023P07, 316T023P10, 316T023P12, 316T023S01, 41-201, 5303912567, 5308067970, 54099H07, AH470131, EA470131, F17-034, GR401, gr407, IGN-1, IGN-7, N316T023P10, AP2150414, PS470131, WP9751123, 9751123, 747868, 816624, AP6013893, PS11747123. Description: This Flat Style Oven Igniter Kit is a high-quality replacement part for specific Frigidaire, Whirlpool gas ranges and wall oven models. It functions to ignite the gas to light the oven burner. This does not replace round igniters, or igniters with blue ceramic.  When you turn on the oven, the igniter is activated, and it starts to glow hot. As it heats up, it ignites the gas that is released from the oven's burner. This process continues until the oven reaches the desired temperature. This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

8053720 Range Genuine Surface Burner Igniter Replaces: W11032529, 8053720, W10850843, W10896683, 3186479, 3186480, 3186482, 3186486, 4455849, AP6038814, PS11770331. 8053720 Range Surface Burner Igniter – Genuine OEM Replacement Ensure reliable burner ignition on your gas range with the 8053720 Surface Burner Igniter. This Genuine OEM part provides the spark needed to ignite the burner quickly and safely. Key Features: ✅ Replaces: W11032529, 8053720, W10850843, W10896683, 3186479, 3186480, 3186482, 3186486, 4455849, AP6038814, PS11770331. ✅ Compatible with Whirlpool, KitchenAid, Maytag, and more ⚡ Supplies consistent spark to surface burner 🛠️ Durable ceramic construction for long-lasting use 🧰 Easy to install – OEM fit and function ⚠️ Disconnect power and gas before installation. Need help confirming compatibility? Contact us! 📦 Part Number: 8053720

Read more less

WP98014893 Oven Genuine Gas Safety Valve Description: The Gas Safety Valve is an OEM replacement part for Whirlpool gas ranges. This important safety device works to automatically shut off the gas supply to the range if abnormal flame conditions, such as flame rollout, occur. Replaces Part Numbers:WP98014893, W11399433, 98014893, 1061522, 98007439, AP6014264, PS11747502.   California Residents only WARNING: California’s Proposition 65

Read more less

XPARTCO 3387134 - 3392519 Dryer Cycling Thermostat and Thermal Fuse Set - Compatible with Whirlpool, Kenmore, Maytag Product Description Maintain safe and efficient dryer operation with the XPARTCO 3387134 - 3392519 Dryer Cycling Thermostat and Thermal Fuse Set. This replacement kit includes one cycling thermostat (3387134, L155-25) and one thermal fuse (3392519), designed as a replacement for select Whirlpool, Kenmore, Maytag, and other compatible dryers. The cycling thermostat regulates drum temperature, while the thermal fuse prevents overheating by cutting power if temperatures exceed safe limits. This set addresses issues like overheating, insufficient heat, no heat, or prolonged drying times. Test the thermal fuse first if the dryer won't heat, as it typically fails before the thermostat. Note: Includes (1) cycling thermostat and (1) thermal fuse. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: Cycling Thermostat: WP3387134, 3387134, 3387135, 3387139, 3-6910, 306910, 326801, 661512, L150-15F, L155-25F, AP6008270, PS11741405. Thermal Fuse: 3392519, WP3392519, 3388651, WE4X857, G4AP0500, 6L4101091C, ET401, 3388651, 694511, 80005, PS11741460, AP6008325. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: LE5700XKW0, LE5920XKW0, WED4815EW1, WED4910XQ1, WED5300SQ0 Kenmore: 110.97591420, 110.97591220, 110.97592420, 110.60072990 Maytag: MDE5500AYW, MDE6000AYW, MDE7600AYW Roper: RED4440VQ1, REX5634KQ1 Amana: NED4655EW0 KitchenAid: KEYE760WWH0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Amana, KitchenAid, and other dryers. 🔧 Specifications: Replacement kit with one cycling thermostat (L155-25 SPST, 120V, 2W) and one thermal fuse (250°F limit, non-resettable). 💪 Reliable Performance: Regulates drum temperature and prevents overheating for safe, efficient drying. 🛠️ Easy Installation: Requires a screwdriver and pliers; typically installed in 15–30 minutes. 🛡️ Effective Fixes: Resolves overheating, insufficient heat, no heat, or prolonged drying times. Product Specification Part Number: XPARTCO 3387134 - 3392519 Component Type: Dryer cycling thermostat and thermal fuse kit Material: Plastic and metal Electrical Specs: Cycling Thermostat: 120V, 2W; L155-25 SPST, opens at 155°F, closes at 130°F  Thermal Fuse: 250°F limit, 125/250V, non-resettable Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running safely and efficiently today! Add to cart now for a reliable fix!

Read more less