Search results for "dryer lint screens and vent"

Genuine GE OEM Part GE WD24X25325 Dishwasher Genuine Fan Vent Assembly Genuine GE door-vent blower/fan assembly for select GE and Haier dishwashers. Product Overview The GE WD24X25325 Dishwasher Fan Vent Assembly is a genuine OEM replacement used in the dishwasher door ventilation system. The blower circulates air through the door vent during the drying portion of the cycle to help reduce retained moisture and improve drying performance. Quick Answer WD24X25325 is a Genuine GE OEM dishwasher door-vent blower/fan motor assembly. It is used on select GE and Haier dishwashers and helps move moist air through the door vent during drying. Common Problems This Part May Fix Poor drying performance Excess moisture remaining after a cycle Door vent fan does not run Unusual noise from the vent/blower area Moist air is not being exhausted through the door vent Replaces and Cross-References WD24X25325, 265D2664G005, U40G12BS3A5-51, AGE25072, AP6972063, EAP12726435, PD00073154, PS12726435. Cross-reference numbers are supplied for identification. Always verify the complete dishwasher model number before ordering. Compatibility Fits select GE and Haier dishwashers. Compatible model examples include: CDT800P2N0S1 CDT805P2N0S1 CDT845P2N3S1 DDT700SBN0TS GDF645SSN0SS GDT645SFN3DS GDT665SFN0DS GDP665SYN3FS PDT715SYN2FS PDT715SFN0DS PDP715SYN3FS QDP555SYN0FS Important: This is only a partial compatibility list. Confirm the exact dishwasher model number before purchase because similar models may use a different vent or blower assembly. Key Features Genuine GE Appliances OEM part Complete door-vent blower/fan assembly Circulates air through the dishwasher door vent Helps reduce moisture during drying For select GE and Haier dishwashers Product Specifications Manufacturer GE Appliances Manufacturer Part Number WD24X25325 Part Type Dishwasher Fan Vent / Door Vent Blower Assembly Condition New Part Quality Genuine OEM Application Dishwasher Door Ventilation / Drying System Approx. Shipping Weight 0.5 lb Installation Notes Disconnect electrical power to the dishwasher at the breaker before service. Access the door vent assembly according to the appliance service procedure. Disconnect the wiring connector carefully before removing the old fan assembly. Transfer or reuse any hardware only as directed for the specific model. Confirm the vent path is clear and the new assembly is fully seated before reassembly. Diagnostic note: Poor drying can also result from rinse-aid settings, heating-system faults, blocked vent passages, or control issues. Confirm the fan assembly is defective before replacing it. Frequently Asked Questions Is WD24X25325 a Genuine GE OEM part? Yes. GE Appliances identifies WD24X25325 as a genuine replacement fan vent assembly. What does this fan assembly do? It circulates air through the dishwasher door vent to help reduce moisture during the drying stage. Does it fit every GE dishwasher? No. It fits specific GE and Haier models. Verify the complete model number before ordering. Is this only the fan motor? This listing is for the complete WD24X25325 fan vent / door-vent blower assembly as supplied by GE. Shop With Confidence Use your dishwasher's complete model number to confirm fitment before purchase. Genuine GE OEMFan Vent AssemblyModel Verification RecommendedFast U.S. Shipping

Read more less

5835EL1002A Dryer Genuine OEM Blower Wheel – Compatible with LG and Kenmore Dryers Product Description Improve airflow and restore efficient drying performance with the 5835EL1002A Dryer Genuine OEM Blower Wheel. This Blower Wheel is a Genuine OEM part for specific Kenmore, LG dryer models. This part circulates air through the dryer drum and out the exhaust vent, ensuring proper airflow for efficient drying of clothes. Replaces Part Numbers 5835EL1002A, 1268176, 5835EL1001A, 5835EL1001B, PD00001766, EAP3528491, AH3528491, EA3528491, AP4438881, PS3528491, DE1002A. Compatibility This Genuine OEM blower wheel fits select LG and Kenmore (LG-built) dryers. Example compatible models include (but are not limited to):LG DLE2516W, DLE1310W, DLE5955W, DLE5977W,Kenmore 796.80272900, 796.80311900, 796.80448900. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🧩 Genuine OEM Replacement – Factory-certified for perfect fit and long-lasting durability 🌬️ Restores Proper Airflow – Ensures strong, consistent air movement through the dryer 🔇 Quiet Operation – Balanced impeller reduces vibration and noise 💪 Durable Construction – Molded from high-strength OEM polymer 🛡️ Fixes Common Issues – Solves long dry times, overheating, noisy operation, or poor airflow 📐 Product Specification Part Number: 5835EL1002A Component Type: Dryer Blower Wheel / Fan Wheel Material: OEM-grade reinforced plastic Mounting: Press-fit onto motor shaft Diameter: Approx. 8 inches (varies slightly by model) Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver, pliers ⚠️ Safety First: Always unplug the dryer before servicing to avoid electrical shock. Steps: Disconnect dryer power and remove the front panel or blower housing cover. Access the blower assembly and inspect the existing wheel. Remove the old blower wheel from the motor shaft. Press the new 5835EL1002A blower wheel firmly onto the shaft. Reassemble all removed panels and restore power. Run a test cycle to confirm smooth airflow and reduced noise. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Genuine OEM Replacement Part 🔄 30-Day Return Policy Improve your dryer’s airflow and performance — Add to Cart Now for a dependable, factory-quality repair!

Read more less

Genuine OEM WP697772 Dryer Blower Wheel The WP697772 is a genuine OEM blower wheel from Whirlpool for Whirlpool-built dryers and washer-dryer combos sold under the Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Crosley, Inglis, and Admiral names. The blower wheel attaches to the drive motor shaft and moves air over the heat source, through the drum, and out the exhaust vent. When the wheel wears, cracks, loses a fin, or comes loose on the shaft, the dryer gets noisy and airflow drops, so clothes take longer to dry. This is a genuine OEM part, not an aftermarket equivalent, so the fit and balance match the original. If your dryer is only noisy, check the blower for lint buildup first, since a clogged wheel can sound like a failing one. Quick Answer The Genuine OEM WP697772 Blower Wheel fixes a Whirlpool-built dryer that is noisy, has weak airflow, or takes too long to dry because the blower wheel is worn, cracked, or damaged. Genuine OEM from Whirlpool. Classic symptom: a rattling, thumping, or squealing noise from the back of the dryer, with damp clothes at the end of a normal cycle. Common Problems This Part Fixes Dryer noisy, with rattling or thumping from the blower area Weak airflow, or clothes taking too long to dry Visibly cracked, chipped, or broken blower fins Blower wheel loose or slipping on the motor shaft Wheel worn out over time Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This blower wheel replaces the following part numbers: WP697772, WPW10211915, 697772, W10211915, 687613, AP6010627, AWP48289,EAP11743811,  FIX11743811, OEM18031890, PD00003053, PS11743811 These are Whirlpool's un-prefixed and earlier numbers for this blower wheel. If your old wheel or parts diagram shows any of them, match against this list. Compatibility This blower wheel is listed for dryers and washer-dryer combos from: Whirlpool, including CEE2760KQ0, WED9470WW1, and WED9400ST1 Kenmore, including 11060052990, 11060056990, and 10687884100 Maytag, including YMEDX700XL0 and MGDX700AG0 KitchenAid, Amana, Crosley, Inglis, and Admiral Note: The model list above is only a sample, since this wheel fits many more models. Confirm fit by matching the number on your old wheel or your parts diagram against the Replaces list, or contact our support team with your model number and we'll verify before you order. Key Features Genuine OEM Whirlpool blower wheel, not an aftermarket equivalent Restores quiet, full airflow through the drum and exhaust Fits select Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Crosley, Inglis, and Admiral dryers and combos Straightforward replacement, typically 15–60 minutes with hand tools Product Specifications Part Number WP697772 OEM Part Number WP697772 Part Type Dryer Blower Wheel Condition Genuine OEM Manufacturer Whirlpool Application Select Whirlpool-Family Dryers & Washer-Dryer Combos Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker, and shut off the gas supply first if it's a gas model. Wear work gloves. Following your model's service guide, remove the front cover to reach the blower housing, then the back cover to access the motor shaft. Hold the motor shaft steady while you unscrew the retaining nut and pull off the old wheel. Reviewers report that the nut is left-hand threaded on these dryers, so check the thread direction before forcing it. Thread the new wheel on while holding the shaft, tighten it, and replace the covers. Clean the blower housing and exhaust duct of lint while you have the dryer open, and inspect the new wheel on arrival for damage. Frequently Asked Questions My dryer is noisy. Is this the part I need? Possibly. Before replacing the wheel, check whether it is clogged with lint, which can cause noise and imbalance. If the wheel is clean but cracked, chipped, or loose on the shaft, replace it. Also check the drum rollers and idler pulley, which can make similar sounds. Is the nut on the shaft left-hand threaded? Reviewers report that it is on these dryers, so turn it the opposite way to a normal nut when removing the old wheel. Check on your dryer before applying force. My old wheel is marked 697772 or W10211915. Will this work? Yes. Both numbers are on the Replaces list. If you're unsure, contact our support team with your model number and we'll confirm. Is this a genuine Whirlpool part? Yes. This is a genuine OEM Whirlpool part, not an aftermarket equivalent. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10245218 Genuine OEM Whirlpool Microwave Vent Grille (Black) The W10245218 is a genuine Whirlpool OEM vent grille for over-the-range microwaves, and also fits select Maytag, Jenn-Air, Kenmore, KitchenAid, Amana, Magic Chef, Admiral, Norge, and Roper models. Finished in black, this grille serves two purposes: it protects the microwave's internal components from physical impact and heat exposure, and it supports proper ventilation airflow to help prevent the unit from overheating. Weighing approximately 3.59 lbs, with package dimensions of 30.24" x 4.76" x 3.46". Common causes of failure include physical impacts, heat exposure over time, or general wear and tear from regular use — a common real-world failure is someone accidentally pulling or leaning on the grille, which can crack the plastic screw mounting tabs and leave the grille hanging loose or detached. Symptoms of a damaged grille include a cracked, broken, or hanging vent grille, or visible physical damage affecting either appearance or the ventilation airflow underneath. It directly replaces AP4411190, 1482738, AH2350384, EA2350384, and PS2350384. Quick Answer The W10245218 Genuine OEM Whirlpool Microwave Vent Grille (Black) fixes Whirlpool, Maytag, Jenn-Air, Kenmore, KitchenAid, Amana, Magic Chef, Admiral, Norge, and Roper over-the-range microwaves with a cracked, broken, or hanging vent grille. Black finish, approx. 30.24" x 4.76" x 3.46". Replaces AP4411190, 1482738, AH2350384, EA2350384, PS2350384. Whirlpool sells several similarly-numbered vent grilles in both black and white finishes for different models — always confirm your exact part number and color before ordering. Common Problems This Part Fixes Cracked or broken vent grille Grille hanging loose or detached from broken mounting tabs Visible physical damage to the grille's appearance Reduced ventilation airflow from a damaged grille Grille damaged by heat exposure or physical impact Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This microwave vent grille directly replaces the following OEM and cross-reference part numbers: W10245218, 1482738, AP4411190, AWP40654, PD00008076, EAP2350384, PS2350384 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This vent grille is compatible with select Whirlpool over-the-range microwaves, and also fits select Maytag, Jenn-Air, Kenmore, KitchenAid, Amana, Magic Chef, Admiral, Norge, and Roper microwaves built on the Whirlpool platform, including model numbers such as UMV1160CS6, UMV1160CB1, WMH1163XVB2, WMH1163XVQ1, WMH1163XVS1, WMH1164XWS1, WMH2175XVB2, WMH2175XVS2, WMH31017AS2, WMH31017AS3, WMH31017AW1, WMH31017FS0, WMH53520CS0, WMH53520CS2, WMH53520CS5, WMH76718AS0, YWMH76718AB0, GMH6185XVQ0, and GH5184XPS4. Note — several similar vent grilles exist: Whirlpool sells multiple vent grilles that can look nearly identical, including part number W10468664 and W10269471 (both white finish) and 8183948 (black finish, different part). This W10245218 is specifically the black-finish grille for its compatible models. Always verify your full model number and confirm the color and exact part number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified fit and black finish Protects internal microwave components from physical impact and heat exposure Supports proper ventilation airflow to help prevent overheating Resolves "cracked or broken grille" and "grille hanging loose" symptoms Approximately 30.24" x 4.76" x 3.46", 3.59 lbs Direct drop-in replacement matching the original mounting Replaces AP4411190, 1482738, AH2350384, EA2350384, and PS2350384 Compatible with Whirlpool, Maytag, Jenn-Air, Kenmore, KitchenAid, Amana, Magic Chef, Admiral, Norge, and Roper microwaves Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W10245218 Part Type Microwave Vent Grille Condition Genuine OEM Brand Whirlpool Application Over-the-Range Microwaves Color Black Weight Approx. 3.59 lbs Dimensions Approx. 30.24" x 4.76" x 3.46" Repair Difficulty Easy — basic hand tools Quantity 1 vent grille Compatible Brands Whirlpool, Maytag, Jenn-Air, Kenmore, KitchenAid, Amana, Magic Chef, Admiral, Norge, Roper Installation Notes ⚠️ Unplug Microwave Before Starting Unplug the microwave before beginning this repair. Wear work gloves to protect your hands. Locate the mounting screws or tabs securing the old vent grille in place, typically along the top or front edge of the unit depending on your model. Support the grille as you remove the mounting hardware, since a partially broken grille can shift or fall once released. Remove the old grille fully. Position the new W10245218 in the same location, aligning it with the mounting points, and secure it with the original screws or clips, taking care not to overtighten and crack the new plastic mounting tabs. Restore power and confirm the grille sits flush and securely in place with no gaps affecting the ventilation airflow. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My vent grille is cracked and hanging loose. What caused this? This is a common failure mode, often caused by someone accidentally pulling, leaning on, or bumping the grille — enough force can crack the plastic screw mounting tabs, leaving the grille hanging or detached even though the rest of the microwave is unaffected. One customer described exactly this scenario: a guest accidentally pulled on the top grille vent, cracking the plastic screw tap and leaving it hanging. How do I know I'm ordering the right color and part number? Whirlpool sells several vent grilles that look very similar across different models, in both black and white finishes. This W10245218 is specifically the black-finish version. Compare your old grille's color and check your full model number against the compatibility list, or check the part number printed on your old grille if it's visible, before ordering. Do I need any special tools to replace this grille? No, this is a straightforward repair with basic hand tools — typically just a Phillips screwdriver to remove and reinstall the mounting screws or clips holding the grille in place. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original black finish and mounting configuration of the vent grille originally installed on your microwave. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WP3392519 Genuine OEM Whirlpool Dryer Thermal Fuse The WP3392519 is a genuine Whirlpool OEM thermal fuse mounted on the blower housing next to the blower fan. This fuse is a one-time safety device: as long as the dryer stays within its normal operating temperature, it does nothing at all, but the instant internal temperatures climb high enough — almost always from restricted airflow — the fuse permanently opens the circuit and cuts power to the dryer. That's why a blown thermal fuse produces such a specific symptom: the dryer won't start at all, with no lights, no tumble, and no response, even though the outlet has power. This fuse opens at approximately 196°F (91°C) and terminates in two 3/16" wire terminals for a direct plug-in fit. Unlike a resettable thermostat, this thermal fuse cannot be reset once it blows — it must be replaced. A blown thermal fuse is almost always a symptom rather than a random failure: restricted exhaust venting is the leading cause, since trapped heat is exactly what the fuse is designed to react to. A shorted heating element or a failed regulating thermostat can also cause the dryer to run hot enough to blow the fuse. It directly replaces 3392519, WP3392519VP, AP6008325, 3388651, 694511, ET401, PS11741460, EAP11741460, AH11741460, EA11741460, PD00002311, G4AP0500, and 80005. Quick Answer The WP3392519 Genuine OEM Whirlpool Dryer Thermal Fuse fixes Whirlpool, Maytag, Kenmore, KitchenAid, Roper, Jenn-Air, and Amana dryers that won't start at all — no lights, no tumble, no response to any button. Opens at approximately 196°F (91°C). Two 3/16" wire terminals. Replaces 3392519, WP3392519VP, AP6008325, 3388651, 694511, ET401, PS11741460, EAP11741460, AH11741460, EA11741460, PD00002311, G4AP0500, 80005. Always inspect and clean the dryer venting when replacing this fuse — a blown fuse is a symptom of restricted airflow, and installing a new fuse without fixing the vent will likely blow it again. Common Problems This Part Fixes Dryer won't start at all — no lights, no tumble, no response to any button Dryer that stopped working suddenly, especially after running unusually hot Dryer runs a short time then shuts off completely and won't restart Repeated blown fuses on a dryer with a known venting or airflow restriction Clothes coming out extremely hot right before the dryer stopped working Dryer that recently smelled like burning or overheating before failing Continuity test shows an open circuit across the old fuse Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermal fuse directly replaces the following OEM and cross-reference part numbers: 3392519, WP3392519, 3388651, WE4X857, G4AP0500, 6L4101, 6L4101091C, ET401, 3388651, 694511, 80005, AWP47582, PD00002311, EAP11741460, AP6008325, PS11741460 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal fuse is compatible with select Whirlpool-built dryers across the Whirlpool family of brands, including: Whirlpool electric and gas dryers — WED, WGD series Maytag electric and gas dryers — MEDC, MGDC series (select Whirlpool-built models) Kenmore dryers (select Whirlpool-built models) KitchenAid, Jenn-Air, and Amana dryers (select models) Roper, Estate, Inglis, and Crosley dryers (select models) Verified model numbers include: MEDC465HW0, MGDC465HW0, WED4850HW0, WED4950HW0, WED49STBW1, WET4024HW0, WET4124HW0, WGD4850HW0, WGD4950HW0, YMEDC465HW0, YWED4850HW0, and YWET4024HW0. Note: This fuse also fits select commercial and stacked washer/dryer combination units on the Whirlpool platform. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified opening temperature and terminal configuration One-time safety device that cuts power if the dryer overheats Opens at approximately 196°F (91°C) Resolves "won't start at all," "stopped working suddenly," and "clothes came out extremely hot before it died" symptoms caused by a blown fuse Two 3/16" wire terminal connectors for a direct plug-in electrical fit Mounts to the blower housing next to the blower fan Replaces 3392519, WP3392519VP, AP6008325, 3388651, 694511, ET401, PS11741460, EAP11741460, AH11741460, EA11741460, PD00002311, G4AP0500, and 80005 Compatible with Whirlpool, Maytag, Kenmore, KitchenAid, Roper, Jenn-Air, and Amana dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WP3392519 Part Type Dryer Thermal Fuse (Thermal Cut-Off) Condition Genuine OEM Brand Whirlpool Opening Temperature Approx. 196°F (91°C) Location Blower housing, next to the blower fan Terminals 2 (3/16" wire terminals) Resettable No — one-time use, must be replaced once blown Dimensions Approx. 2" x 1/2" Repair Difficulty Medium — basic disassembly required Quantity 1 thermal fuse Compatible Brands Whirlpool, Maytag, Kenmore, KitchenAid, Roper, Jenn-Air, Amana, Estate, Inglis, Crosley Installation Notes ⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel: remove the screws securing the panel to reach the blower housing where the fuse is mounted. Photograph the wiring before disconnecting the wire terminals from the old fuse. Remove the mounting screw holding the fuse in place and pull it free, disconnecting both wire terminals. Before installing the new fuse, test it for continuity with a multimeter to confirm it's good out of the box, and test the old one to confirm it's actually blown (no continuity) rather than assuming. This is the most important step: fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. A blown thermal fuse is a symptom of restricted airflow, and skipping this step means the new fuse is likely to blow again. Install the new WP3392519 in the same mounting position, reconnect both wire terminals, and secure the mounting screw. Reinstall the rear panel, restore power, and run a test cycle to confirm normal heating and shutoff behavior. Tools needed: Phillips or nut driver (model-dependent), multimeter, vent brush or vacuum attachment for cleaning ductwork, work gloves. Frequently Asked Questions My dryer has no power at all and the lights won't turn on. Is this the thermal fuse? It's a strong possibility. When this thermal fuse blows, it cuts power broadly enough that the console lights and control panel can go completely dark, not just the heating function — that's a normal result of how this fuse is wired into the circuit. Before replacing it, confirm the outlet has power and the breaker hasn't tripped, then check the fuse for continuity with a multimeter. If it shows no continuity, this fuse is the correct fix, though it's also worth checking the exhaust ducting since that's the most common underlying cause. I replaced the fuse and it blew again. What's going on? This is a strong sign that the underlying cause — almost always restricted airflow — was never addressed. Thermal fuses don't fail from age; they blow because the dryer overheated. If a new fuse keeps blowing, thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. If airflow checks out and the fuse still blows, have the heating element and cycling thermostat checked as well, since a component stuck in the "on" position can also drive excess heat. Can I just reset the thermal fuse instead of replacing it? No. Unlike a cycling thermostat, this thermal fuse is a one-time safety device — once it blows, its internal circuit is permanently broken and it cannot be reset or repaired. Replacement is the only option. My clothes came out extremely hot right before the dryer died. Is that related? Yes, this is a classic warning sign. Clothes coming out unusually hot indicates the dryer was already running hotter than normal, which is exactly the condition that leads to a blown thermal fuse. If you noticed this before the dryer stopped working, it strongly points to a ventilation or airflow problem that should be fully addressed before running the dryer again. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original opening temperature, terminal configuration, and mounting position of the thermal fuse originally installed in your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3392519 Dryer Thermal Fuse Replaces WP3392519 The XPARTCO 3392519 is an aftermarket replacement dryer thermal fuse compatible with select gas and electric dryers from Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, and Magic Chef. The thermal fuse is a critical one-time-use safety device mounted on the exhaust duct or blower wheel housing that monitors the dryer's operating temperature. When the dryer overheats — typically due to a clogged exhaust vent or restricted airflow — the thermal fuse permanently opens the circuit and cuts power to the heating system to prevent a fire. Once blown, the thermal fuse cannot be reset and must be replaced. This part measures 2 inches long x 1/2 inch wide, features two 3/16-inch terminals, and opens at approximately 196°F (91°C). Important: always check and clear the exhaust vent when replacing this fuse, as restricted airflow is the most common cause of thermal fuse failure. Quick Answer The XPARTCO 3392519 Dryer Thermal Fuse fixes dryers that won't start, won't heat, or stop mid-cycle due to overheating. It is a one-time-use safety fuse that permanently opens at 196°F (91°C) to cut power and prevent fires. Compatible with select Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, and Magic Chef dryers. Replaces WP3392519 and many other part numbers. Common Problems This Part Fixes Dryer won't start at all Dryer runs but produces no heat Dryer stops mid-cycle and won't restart Timer advances but drum does not heat Dryer shuts off too soon before clothes are dry No continuity detected across fuse terminals during testing Replaces Part Numbers This thermal fuse directly replaces the following OEM and cross-reference part numbers: 3392519, WP3392519, 3388651, WE4X857, G4AP0500, 6L4101, 6L4101091C, ET401, 3388651, 694511, 80005, AWP47582, PD00002311, EAP11741460, AP6008325, PS11741460 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal fuse is compatible with select gas and electric dryers from the following brands: Whirlpool dryers (including Duet and Cabrio series) Kenmore / Sears dryers (including Elite series) KitchenAid dryers Maytag dryers (including Centennial and Neptune series) Roper dryers Estate dryers Inglis dryers Crosley dryers Amana dryers Admiral dryers Magic Chef dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features One-time-use safety device — permanently opens at 196°F (91°C) to cut power and prevent dryer fires Mounts on the exhaust duct or blower wheel housing — easy access for DIY replacement Aftermarket replacement built to OEM-equivalent quality standards 2-terminal design — direct drop-in replacement, no modification required Broad compatibility across 11 major appliance brands DIY-friendly repair — installs with basic hand tools in under 30 minutes Budget-friendly safety fix — one of the most common and least expensive dryer repairs Product Specifications Part Number 3392519 Part Type Dryer Thermal Fuse Condition Aftermarket Replacement Application Gas and Electric Dryers Opening Temperature 196°F (91°C) Length 2 inches Width 1/2 inch Terminal Size 3/16 inch (2 terminals) Resettable No — one-time use only, must be replaced when blown Location on Dryer Exhaust duct / blower wheel housing Compatible Brands Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, Magic Chef Installation Notes ⚠️ Safety First — Unplug Dryer and Shut Off Gas Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. The thermal fuse is located on the exhaust duct or blower wheel housing — access it by removing the back or front panel depending on your dryer model. Disconnect the two wire terminals from the old fuse, remove the fuse from its bracket, install the new fuse in the same position, reconnect the terminals, and reassemble the panel. Tools needed: Phillips screwdriver, 1/4-inch nut driver, and a multimeter to confirm the new fuse has continuity. ⚠️ Important: Before completing the repair, always check and clear the exhaust vent of any lint buildup — a blocked vent is the most common cause of thermal fuse failure and will blow the new fuse if not corrected. Frequently Asked Questions Will the 3392519 fit my dryer? This thermal fuse is compatible with select gas and electric dryers from Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, and Magic Chef. Use the model search above to verify your model, or contact our support team before ordering. What does a dryer thermal fuse do? The thermal fuse is a one-time-use safety device that monitors the temperature inside the dryer. When the dryer overheats — typically due to a clogged exhaust vent — the fuse permanently opens the circuit, cutting power to the heating system to prevent a fire. Once blown, it cannot be reset and must be replaced. How do I know if my thermal fuse is blown? Test the fuse with a multimeter set to continuity mode. Touch the probes to each of the two terminals. A working fuse will show continuity (beep or near-zero ohms). A blown fuse will show no continuity (open circuit). If there is no continuity, the fuse is blown and must be replaced. Why did my thermal fuse blow? The most common cause is restricted airflow due to a clogged or kinked exhaust vent, a plugged lint trap, or a damaged blower wheel. Always check and clear the exhaust vent before or after replacing the fuse — failing to do so will cause the new fuse to blow again. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is designed to deliver reliable overheat protection at a more affordable price point. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock parts for major appliance brands and ship quickly from our U.S. warehouse. Our team is available to help you verify compatibility before you buy. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

AGM30045804 Genuine OEM LG Dryer Thermistor and Thermostat Kit The AGM30045804 is a genuine LG OEM high-limit thermostat and thermistor kit for LG dryers. These two components work together in the same temperature-regulation circuit: the thermistor is a temperature sensor, mounted in the blower housing with its wire harness included, that continuously reports drum temperature to the control board so it can fine-tune heat output throughout the cycle. The high-limit thermostat is a safety switch that automatically shuts off the heating element if temperatures climb past a safe threshold, then resets itself once the dryer cools, without needing to be replaced the way a thermal fuse does. Because these two parts share the same circuit and tend to wear or fail around a similar timeline, LG sells and services them together as one kit rather than as separate individual parts. Symptoms of failure in this circuit include the dryer overheating (which can scorch clothing or, left unaddressed, pose a fire risk), the dryer running with little or no heat, drying times that have become inconsistent, an error code related to temperature control on the display, or clothes coming out damp after a full cycle. It directly replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, and PS16732335. Quick Answer The AGM30045804 Genuine OEM LG Dryer Thermistor and Thermostat Kit fixes LG (and select Kenmore, GE-branded LG-built) dryers with overheating, little or no heat, inconsistent drying times, a temperature-related error code, or clothes coming out damp after a full cycle. High-limit thermostat + thermistor with wire harness. Replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, PS16732335. If you've already replaced the high-limit thermostat alone and the problem returns, this combined kit — which also addresses the thermistor — is the next step. What's In The Kit Component Function High-Limit Thermostat Automatically shuts off the heating element if temperature exceeds safe limits, then resets itself once the dryer cools. Thermistor (with wire harness) Continuously senses drum/blower housing temperature and reports it to the control board to regulate heat output throughout the cycle. Common Problems This Kit Fixes Dryer overheating, sometimes scorching or damaging clothing Dryer running with little or no heat Inconsistent drying times — cycle shuts off too early or runs longer than necessary Temperature-related error code displayed on the control panel Clothes remaining damp after a full drying cycle High-limit thermostat that keeps tripping repeatedly Dryer that has already had its high-limit thermostat replaced once but the problem returned Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermistor and thermostat kit directly replaces the following OEM and cross-reference part numbers: AGM30045804, 6931EL3003C, 6931EL3004B, 6931EL3002B, 6931EL3003F, 6931EL3003G, 6323EL2001B, ALG53406, AP7206815, EAP16732335, PD00079467, PS16732335 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This kit is compatible with select LG dryers, and also fits select Kenmore and GE-branded dryers built on the LG platform. Note: A specific verified model list was not consistently available across sources at the time this page was built. Some parts diagrams reference additional related thermostat components (such as a separate blower thermostat) beyond what's included in this kit — if your repair involves more than a high-limit thermostat and thermistor, or if you're unsure exactly what's failed on your model, contact our support team with your model number and we'll help confirm which parts you need before you order. Key Features Genuine LG OEM part — factory-specified resistance values and switch thresholds Combined kit addresses the high-limit thermostat and thermistor together, since both share the same temperature-regulation circuit Resolves "overheating," "little or no heat," "inconsistent drying," and "damp clothes after a full cycle" symptoms Thermistor ships with its wire harness included High-limit thermostat resets automatically after tripping — no replacement needed after each trip Direct drop-in replacement for both original components Replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, and PS16732335 Compatible with LG and select Kenmore and GE-branded LG-built dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number AGM30045804 Part Type Dryer High-Limit Thermostat and Thermistor Kit Condition Genuine OEM Brand LG Kit Contents High-limit thermostat + thermistor with wire harness Thermistor Location Blower housing High-Limit Thermostat Type Automatically resetting Repair Difficulty Easy to Moderate — 30 to 60 minutes Compatible Brands LG, select Kenmore, GE (LG-built models) Installation Notes ⚠️ Unplug Dryer Before Starting — Let It Cool Fully First Disconnect power at the outlet or shut off the circuit breaker before beginning, and allow the dryer to cool completely if it was recently run. Wear work gloves. Access on many LG models follows this general sequence: remove the lint screen, then remove the two front panel screws underneath it, the two screws on the face of the panel, and the two screws holding the blower cover in place. Disconnect the door switch connector and remove the front panel. With the front open, release the drive belt from the tensioner and remove the drum to access the blower housing where the thermistor is located. Photograph the wiring connections before disconnecting anything, since the thermistor and high-limit thermostat can be easy to confuse with other similar-looking components nearby. Disconnect and remove the old thermistor and high-limit thermostat, noting their exact mounting positions. Install the new components from this kit in the same positions, reconnecting wiring exactly as photographed. Reinstall the drum, re-tension the belt over the tensioner, and reassemble the front panel, blower cover, and lint screen area in reverse order. Restore power and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions I already replaced the high-limit thermostat, but it keeps tripping. Why would I need this kit instead? This is a well-documented pattern. If the thermistor — the sensor that reports temperature to the control board — is misreading heat, the control can keep driving the heating element past the point where the high-limit thermostat has to trip repeatedly to protect the dryer, even with a brand-new thermostat installed. Replacing the thermistor alongside the thermostat addresses the root cause rather than just the symptom, which is exactly why LG packages them together as one kit. What's the difference between the thermistor and the high-limit thermostat? The thermistor is a sensor, not a switch — it's a variable resistor whose resistance changes with temperature, and the control board reads that value continuously to regulate heat output throughout the cycle. The high-limit thermostat is a safety switch that does one job: it shuts off the heating element automatically if temperature exceeds a safe limit, then resets itself once things cool down. A failing thermistor causes inconsistent or inaccurate heat regulation; a failing high-limit thermostat causes the dryer to shut off unexpectedly or fail to protect against overheating. My parts diagram shows more thermostat-like parts than what's in this kit. Did I order the wrong thing? Not necessarily — some LG dryer models have additional related components, such as a separate blower thermostat, that are not part of this specific kit. This kit covers the high-limit thermostat and thermistor. If your repair calls for additional related parts, or if you're not sure exactly which components your model needs, contact our support team with your model number and we'll help you confirm the complete parts list before you order. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It includes the same resistance values, switch threshold, and wire harness configuration as the high-limit thermostat and thermistor originally installed in your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

🚪 XPARTCO 131658800 Dryer Door Catch This Door Catch is a replacement part for specific Kenmore, Frigidaire dryer models. It includes the door catch. This part ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently. Common causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly. Fix a loose or non-latching dryer door with this aftermarket replacement for part number 131658800. This dryer door catch holds the dryer door securely closed during operation to ensure proper airflow and drying performance. Designed to fit many Frigidaire, Kenmore, Electrolux, and Crosley dryers. ✅ Key Features: High-quality aftermarket replacement for part #131658800 Made from durable plastic for long-lasting use Designed to securely latch the door shut Simple snap-in installation — no tools required Helps prevent cycle interruption due to door opening 🔁 Replaces OEM Part Numbers: 131658800, 131658820, 131658845, 00634863, 07521419, 08015370, 134548000, 134548045, 3004967, 3202755, 3281055, 5303281055, 5307521419, 7521419, 835, AH418433, EA418433, F141735-000, F141735000, F62661-4, K1300884, K1301594, K1308079, K1309301, N8010215, Q0000401002, Q000504551, Q000504553, Q504551, Q504553, WQ504551, WQ504553, AP2107362, PS418433, WE01X25316, AP6037347, 4512762, PS11766999. ⚠️ Common Symptoms Fixed: Dryer door won’t stay closed Dryer won’t start due to open door switch Door pops open during a cycle Visible wear or damage to original catch 🧰 Compatible Brands: ✔️ Frigidaire✔️ Electrolux✔️ Kenmore (Frigidaire-built)✔️ Gibson✔️ Tappan✔️ Crosley✔️ White-Westinghouse 📌 Need help verifying compatibility? Send us your dryer’s model number — we’ll check it for you. 🚚 Why Buy from Parts-O-Matic? ✅ Reliable aftermarket performance ✅ Always Fast and Free U.S. shipping ✅ Easy DIY repair with trusted support ✅ Backed by excellent customer service 🛒 Fix your dryer’s latching issue today — order the 131658800 dryer door catch from Parts-O-Matic.com, and enjoy fast, free U.S. shipping!

Read more less

XPARTCO 661570 Dryer Drum Belt Replaces 661570V The XPARTCO 661570 is an aftermarket replacement dryer drum belt compatible with select Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Crosley, Admiral, and Speed Queen dryers. The drum belt wraps around the outside of the dryer drum, loops around the idler pulley and motor pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from high-strength rubber, this 4-rib belt measures 93-1/2 inches long x 1/4 inch wide x 1/8 inch high with 4 ribs and 3 grooves. It is a direct drop-in replacement for OEM part numbers 661570V and 661570, and is part of the 4392067 dryer repair kit. It pairs with the W10837240 idler pulley and WPW10314173 drum rollers for a complete drum drive overhaul. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 661570 Dryer Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is present during operation. Compatible with select Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Crosley, Admiral, and Speed Queen dryers. Measures 93-1/2" L x 1/4" W x 1/8" H with 4 ribs and 3 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Burning rubber smell coming from the dryer Visible broken or frayed belt pieces found inside the dryer cabinet Dryer shuts off shortly after starting due to drum not rotating Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: 661570V, 661570, 3387610, 3389728, 3393999, 339728, 4248258, 661570VP, AWP761693, OEM17951196, PD00023608, FIX382430, AP5983729, PS11722115. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Maytag dryers (gas and electric) Kenmore / Sears dryers (select Whirlpool-built models) Amana dryers KitchenAid dryers Crosley dryers Admiral dryers Speed Queen dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the idler pulley and motor pulley for smooth, consistent tumbling every cycle 93-1/2" length x 1/4" width x 1/8" height — 4-rib, 3-groove design for a secure, slip-free grip on the pulleys Made from high-strength rubber — resists cracking, stretching, heat damage, and oil Direct replacement for OEM part numbers 661570V and 661570 — no modification required Part of the 4392067 dryer repair kit — pairs with W10837240 idler pulley and WPW10314173 drum rollers Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number 661570 OEM Part Number 661570V Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Gas and Electric Dryers Length 93-1/2 inches Width 1/4 inch Height 1/8 inch Ribs 4 ribs, 3 grooves Material High-strength rubber Color Black Compatible Brands Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Crosley, Admiral, Speed Queen Part of Kit 4392067 Dryer Repair Kit Often Replaced With W10837240 Idler Pulley, WPW10314173 Drum Rollers Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen and unscrew the Phillips screws inside the lint screen housing. Use a putty knife to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release the belt from the idler pulley, lift the drum slightly, and slide the old belt off. Loop the new 661570 belt around the drum with the ribbed side facing inward toward the drum. Route the belt around the idler pulley and motor pulley — consult your dryer's service manual or a model-specific repair video for the correct belt path. Reassemble and run a test cycle. Tip: While the drum is out, inspect and replace the idler pulley (W10837240) and drum rollers (WPW10314173) if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions What is the difference between 661570 and 661570V? These are the same belt. 661570V is the updated OEM part number (the "V" denotes the current version) that superseded the original 661570. Both numbers refer to the identical drum belt — this aftermarket replacement is compatible with both. How does the 661570 differ from the 341241 and W10205415 belts? All three are Whirlpool-family dryer drum belts, but they differ in length, width, and rib count. The 661570 is 93-1/2" long x 1/4" wide with 4 ribs and 3 grooves. The 341241 is 92-1/4" long x 1/4" wide with 4 ribs and 3 grooves. The W10205415 is 92" long x 3/8" wide with 5 ribs and 4 grooves. They are not interchangeable — always use the part number specific to your dryer model. How do I know if my drum belt is broken? The most obvious sign is that the dryer motor hums but the drum does not spin. You may also notice a thumping or slapping sound, a burning rubber smell, or damp clothes after a full drying cycle. Open the dryer cabinet to visually confirm if the belt is broken, frayed, or stretched out of shape. Should I also replace the idler pulley and drum rollers? Yes — since the dryer is already disassembled, it is highly recommended to inspect and replace the idler pulley (W10837240) and drum support rollers (WPW10314173) at the same time. All three parts wear together and are sold together in the 4392067 dryer repair kit. Replacing all three prevents having to disassemble the dryer again in the near future. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is made from high-strength rubber to match the dimensions and performance of the original 661570V belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

131775600 Dryer Genuine Blower Wheel and Housing Complete housing and captive blower assembly. Fits specific Frigidaire, Electrolux dryer models. Replaces Part Numbers: 131775600, 131775610, AH418726, EA418726, OEM6322823, AP2107606, PS418726. Description: This Blower Housing Assembly is a Genuine part for specific Frigidaire dryer models. It houses the blower wheel, which circulates air through the dryer drum and out the exhaust. This assembly ensures that hot air is efficiently directed through the dryer to dry clothes properly.  Common Cause is the blower housing assembly can become damaged or worn out, affecting the dryer's performance. Causes of a bad blower housing assembly can include accumulation of lint or debris, wear and tear from frequent use, or physical damage to the housing or blower wheel.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WH23X38617 Genuine OEM GE Washer Drain Pump Filter with Seal The WH23X38617 is a Genuine OEM GE replacement drain pump filter with seal, compatible with select GE, GE Profile, and GE 2-in-1 Washer/Dryer Combo models. The pump filter sits inside the drain pump housing and traps lint, coins, hair, and small debris before they reach the pump impeller. Keeping this filter clean and intact is essential for proper drainage — a clogged or damaged filter causes slow draining, standing water in the tub, and can strain the drain pump over time. This genuine OEM part is manufactured by GE to factory specifications and includes both the pump filter and the seal. The seal prevents leaks at the pump clean-out when the filter is installed correctly. The filter body is blue plastic with rubber seal components, measuring approximately 6" L x 3" W x 3" H. It directly replaces part number AP7243923 and installs with a simple counterclockwise removal and clockwise installation — no special tools required. Quick Answer The WH23X38617 Genuine OEM GE Washer Drain Pump Filter with Seal fixes GE washers that drain slowly, leave standing water in the tub, or leak near the pump access panel. The filter traps lint and debris to protect the pump impeller. Includes filter and seal. Blue plastic/rubber, approx. 6" L x 3" W x 3" H. Twist-out installation — no tools needed. Compatible with GE, GE Profile, and GE 2-in-1 Washer/Dryer Combo models. Common Problems This Part Fixes Washer draining slowly or not draining at all after a wash cycle Standing water remaining in the drum at the end of a cycle Water leaking from the pump filter access panel at the front of the washer Error codes related to drain or pump failure on compatible GE models Unusual noise from the drain pump caused by debris reaching the impeller Cracked, stripped, or missing filter cap allowing debris into the pump housing Damaged or deteriorated seal causing leaks at the filter access port Replaces Part Numbers This drain pump filter directly replaces the following part numbers: WH23X38617, WH23X38617, FIX17874614, AGE1014282, PD00090185, AP7243923, PS17874614. Contact our support team with your model number if you need help confirming compatibility before ordering. Compatibility This drain pump filter is compatible with select washers and laundry centers from the following GE product lines: GE front-load washers (select models) GE Profile front-load washers (select models) GE 2-in-1 Washer/Dryer Combo (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Traps lint, coins, hair, and small debris to protect the drain pump impeller from damage Includes both the pump filter and seal — everything needed for a complete replacement Seal prevents water leaks at the pump filter access port when the filter is properly installed Blue plastic and rubber construction — durable and chemical resistant Dimensions: approximately 6" L x 3" W x 3" H Twist-out installation — turns counterclockwise to remove, clockwise to install; no special tools required Should be cleaned regularly (every 1–3 months) and replaced when cracked, stripped, or leaking Product Specifications Part Number WH23X38617 Part Type Washer Drain Pump Filter with Seal Condition Genuine OEM Application Front-load washers and 2-in-1 washer/dryer combos Approximate Dimensions 6" L x 3" W x 3" H Color Blue Material Plastic / Rubber Includes Pump filter and seal Installation Twist-out / twist-in — no special tools required Compatible Brands GE, GE Profile Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before servicing the drain pump filter. Place towels or a shallow pan beneath the filter access panel to catch residual water — there will always be some water remaining in the pump housing when you remove the filter. Locate the pump filter access panel at the lower front of the washer and open or remove it. Turn the old WH23X38617 filter counterclockwise to loosen and remove it. Clear any debris from the filter housing and wipe the area clean. Install the new filter and seal by inserting it into the housing and turning it clockwise until snug — do not overtighten. Close or reinstall the access panel, restore water supply and power, then run a short cycle to verify proper drainage and confirm there are no leaks at the filter port. Tip: Clean the pump filter every 1–3 months as part of regular washer maintenance to prevent buildup. Tools needed: None for the filter itself; a screwdriver may be needed to open the access panel on some models. Frequently Asked Questions What does the drain pump filter do? The drain pump filter catches lint, coins, hair, buttons, and other small items before they can reach the drain pump impeller. Without the filter, debris can jam or damage the impeller — leading to pump failure, loud grinding noises, or a washer that won't drain. The filter also acts as a cleanout access point so you can periodically remove accumulated debris without disassembling the pump. How often should I clean or replace the pump filter? GE recommends cleaning the pump filter every 1–3 months depending on how frequently you run the washer and how much lint your laundry produces. The filter should be replaced rather than just cleaned if it is cracked, stripped at the threads, or if the seal is damaged or missing — a compromised filter or seal will leak water from the access port. Why is water leaking from the front of my GE washer near the bottom? A leak at the lower front of the washer near the pump access panel is most often caused by a damaged or deteriorated pump filter seal, a cracked filter body, or a filter that is not fully tightened. Replacing the WH23X38617 pump filter and seal resolves this in most cases. Make sure the new filter is hand-tightened snugly — do not overtighten, as this can crack the housing. Will there be water when I remove the pump filter? Yes — there is always residual water in the drain pump housing. Before removing the filter, place towels and a shallow pan or tray directly under the access panel to catch the water. The amount varies depending on how much water remains in the washer after the last cycle. Running a drain-only cycle immediately before removing the filter will minimize the amount of water released. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same pump filter and seal that GE installs in compatible models from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO Y312959 Dryer Drum Belt Replaces WPY312959 The XPARTCO Y312959 is an aftermarket replacement dryer drum drive belt compatible with a wide range of Maytag, Jenn-Air, Whirlpool, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryers — including the long-running vintage Maytag DE and DG halo-of-heat series. The drum belt is a critical component that connects the drive motor to the drum. It wraps all the way around the drum's circumference, passes around a spring-loaded idler (tension) pulley, and connects to the drive motor pulley. When the motor runs, it drives the belt, which rotates the drum to tumble clothes for even drying. Over time, drive belts fail from normal wear, cracking or fraying from age and repeated flexing, exposure to heat and lint buildup, stretching that causes slipping, or sudden breakage. Constructed from durable black rubber. Dimensions: 100" long x 3/8" (5/16") wide, with 5 ribs and 4 grooves. Includes instructions. It directly replaces Y312959, WPY312959, WPY312959VP, 312959, 3-12959, 3-14774, 314774, 1000H5, 8195-959, LB234, P46-150, P46-151, 1246110, 6-3129590, AP6024192, EAP11757542, PD00028571, and PS11757542. Important: install the belt with the grooved side against the motor pulley and the smooth side against the drum. Because the belt is symmetrical, it can be installed with either end facing out. Often replaced together with the idler pulley (WP6-3037050) and drum support roller kit (12001541 / 303373K), sold separately. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO Y312959 Dryer Drum Belt fixes Maytag, Jenn-Air, Whirlpool, Amana, and Kenmore dryers where the drum won't turn (motor runs but drum stays still), the drum spins slowly, or the dryer makes loud squealing/thumping noises. 100"L x 3/8"W. 5 ribs, 4 grooves. Black rubber. Replaces WPY312959, WPY312959VP, 312959, 3-12959, 3-14774, 314774, 1000H5, 8195-959, LB234, P46-150, P46-151, 1246110, 6-3129590, AP6024192, EAP11757542, PS11757542. Install grooved side against the motor pulley, smooth side against the drum. Often paired with idler pulley WP6-3037050 and drum roller kit 12001541. Common Problems This Part Fixes Dryer drum doesn't turn — motor runs but drum stays still (belt snapped) Dryer drum rotates slowly or intermittently — belt worn or slipping Loud squealing, squeaking, or thumping noises during operation — belt cracked, glazed, or misaligned Clothes taking much longer than normal to dry — drum not tumbling clothes effectively Visible cracks, fraying, or glazing on the belt surface Belt broken completely — often heard as a loud snap during operation Drum spins freely by hand with no resistance — a clear sign the belt has snapped Belt worn thin or stretched after decades of use on a vintage Maytag dryer Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer drum belt directly replaces the following OEM and cross-reference part numbers: Y312959, WPY312959, 1000H5, 1246110, 3-12959, 3-14774, 312959, 314774, 8195-959, P46-150, P46-151, 6 3129590, AP6024192, AWP51437, EAP11757542, PD00028571, PS11757542 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This dryer drum belt is compatible with select dryers from the following brands: Maytag electric dryers — DE106, DE107, DE110, DE180, DE18CA/CM/CS/CT, DE19CA/CD/CS/CT, DE210, DE212, DE21CA/CM/CS/CT, DE22CA/CS/CT, DE23CD, DE24CA/CM/CS/CT, DE25CS, DE26CA/CD/CS/CT, DE27CA/CS/CT, DE303, DE308, DE309, DE312, DE313, DE382, DE4000, DE408-DE9900 series and many more Maytag gas dryers — DG106, DG107, DG110, DG18CA/CM/CS/CT, DG19CA/CD/CS/CT, DG210, DG212, DG21CA/CM/CS/CT, DG22CA/CS and related DG-series models Maytag dryers — LDE and LDG series (LDE7304ACE, LDE8406ACE/ACM/ADE, LDE8410, LDG8424AAE, LDG9304AAM and related) Jenn-Air dryers (select models) Whirlpool dryers (select Whirlpool-built models) Amana, Magic Chef, Admiral, Norge, Roper dryers (select Whirlpool/Maytag-built models) Kenmore / Sears dryers (select Whirlpool/Maytag-built models) Note: When you replace the drum belt, this is also the ideal time to inspect the idler (tension) pulley (WP6-3037050) and the drum support rollers (kit 12001541 / 303373K) — they wear from the same friction cycles as the belt, and if they're rough, seized, or noisy, the new belt will wear out prematurely. Before replacing the belt due to noise, check the drum support rollers and idler pulley and replace if you see signs of wear. Always verify your dryer model number before ordering. Key Features Dryer drum drive belt — connects the motor pulley to the drum to enable tumbling during drying cycles Resolves "drum won't turn," "loud squealing noise," and "long dry times" symptoms when caused by belt failure Durable black rubber construction — engineered to withstand thousands of hours of high-temperature, high-friction operation Dimensions: 100" long x 3/8" (5/16") wide with 5 ribs and 4 grooves Install with the grooved side against the motor pulley and the smooth side against the drum Symmetrical design — can be installed with either end facing out Includes instructions Replaces WPY312959, WPY312959VP, 312959, 3-12959, 3-14774, 314774, 1000H5, 8195-959, LB234, P46-150, P46-151, 1246110, 6-3129590, AP6024192, EAP11757542, and PS11757542 Compatible with vintage Maytag DE/DG series, LDE/LDG series, plus Jenn-Air, Whirlpool, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryers Often replaced together with the idler pulley (WP6-3037050) and drum support roller kit (12001541 / 303373K), sold separately Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number Y312959 OEM Part Number WPY312959 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Dryers (Maytag / Whirlpool platform) Length 100" Width 3/8" (5/16") Ribs / Grooves 5 ribs / 4 grooves Color Black Material Rubber Installation Orientation Grooved side against motor pulley, smooth side against drum Often Paired With Idler Pulley (WP6-3037050), Drum Roller Kit (12001541 / 303373K) Compatible Brands Maytag, Jenn-Air, Whirlpool, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Wear Work Gloves — Grooved Side Against Motor Pulley Disconnect power at the breaker or outlet before beginning. Wear work gloves to protect your hands from sharp sheet metal edges inside the dryer cabinet. Access the drum by removing the appropriate panels — the specific procedure varies by model, but on many vintage Maytag dryers this involves removing the front or top panel. Photograph the belt routing before disassembly if any belt fragments remain. Remove any pieces of the old broken belt from around the drum, motor pulley, and idler pulley, and vacuum out accumulated lint and belt dust. Clean any belt dust off the drum. Route the new Y312959 belt around the drum. Install with the grooved (ribbed) side against the motor pulley and the smooth side against the drum — this is the correct orientation for proper drive engagement. Because the belt is symmetrical, either end can face outward. A helpful tip from experienced installers: use two small pieces of tape to hold the belt against the drum while you lace it onto the idler and motor pulleys. From under or behind the drum, route the belt around the idler (tension) pulley and the drive motor pulley following the belt diagram for your model. Rotate the drum by hand a few full turns to confirm the belt seats correctly and rides smoothly without binding. While you have the machine apart, check that the idler pulley and drum support rollers spin freely — if they're rough or noisy, replace them now to protect the new belt. Reassemble the panels, restore power, and run a test cycle. Tools needed: Phillips screwdriver, nut driver, socket/ratchet, vacuum, work gloves, tape (helpful for holding the belt). Frequently Asked Questions My dryer runs but the drum won't turn — is the belt the problem? Almost certainly, yes. When the motor runs (you hear the humming) but the drum stays still, the belt has almost always snapped. To confirm without opening the dryer: reach in and try turning the drum by hand. If it spins freely with no resistance whatsoever, the belt is broken. If it turns but feels notchy or resistant, the belt may still be intact but the drum rollers or bearings could be the issue. Opening the dryer to inspect is the definitive check — a snapped belt will be lying in the bottom of the cabinet. On decades-old Maytag dryers, a belt that finally snapped from age is one of the most common repairs. Which way does the belt go — grooves in or out? Install the belt with the grooved (ribbed) side facing the motor pulley and the smooth side against the drum. The ribs engage the grooved motor pulley for positive drive without slipping, while the smooth side rides against the large drum surface. Note that this is the opposite orientation from some other dryer belts (like certain Frigidaire belts where grooves face the drum) — so don't assume; follow the grooves-against-motor-pulley rule for this Maytag/Whirlpool-platform belt. The belt is symmetrical end-to-end, so either end can face outward; only the grooved-vs-smooth orientation matters. Should I replace the idler pulley and drum rollers at the same time? It's strongly recommended, especially on older dryers. The idler (tension) pulley (WP6-3037050) keeps the belt under proper tension, and the drum support rollers (kit 12001541 / 303373K) carry the drum's weight as it turns. All wear from the same friction and heat cycles as the belt. In fact, a common piece of repair advice is: before you replace the belt due to noise, check the drum support rollers and idler pulley first — worn rollers or a seized idler are frequent noise sources, and if you replace only the belt, the new belt may wear out prematurely against a bad pulley. Since the dryer is already apart, replacing all three together is efficient and saves a repeat repair. What's the difference between Y312959 and WPY312959? These are the same drum belt across production revisions. Y312959 was the earlier Maytag part number and WPY312959 is the Whirlpool-era part number (after Whirlpool acquired Maytag) for the same belt. WPY312959VP is a variant packaging code. All are physically and functionally identical — if your dryer's parts diagram shows any of these numbers, this listing is the correct replacement. The many other cross-references (3-12959, 314774, LB234, P46-150, etc.) reflect the belt's long production history across decades of Maytag dryers. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Maytag/Whirlpool OEM part, but is manufactured from durable rubber to match the dimensions (100"L x 3/8"W), rib and groove pattern (5 ribs, 4 grooves), and drive function of the original Y312959/WPY312959 drum belt used in compatible Maytag, Jenn-Air, Whirlpool, Amana, and Kenmore dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less