Search results for "hvac motor"

XPARTCO XPDC40X5-450R Dual Run Capacitor (40/5 MFD, 450V, Round) The XPARTCO XPDC40X5-450R is a universal dual run capacitor for central air conditioners, heat pumps, and condensing units. A run capacitor works alongside a single-phase AC motor to keep it running efficiently once it's started, boosting torque and correcting the phase of the current feeding the motor's windings. This is a dual capacitor, meaning it combines two separate capacitors — one for the compressor, one for the condenser fan motor — into a single three-terminal can, which is why nearly every residential outdoor AC unit uses exactly this style of component to run both motors from one part. Rated 40 MFD for the compressor circuit and 5 MFD for the fan motor circuit, at 450VAC, in a round aluminum can housing. Because a capacitor's voltage rating is a ceiling rather than a fixed match, this 450V-rated capacitor can safely replace an original capacitor rated 370V or 440V — going higher on voltage is always safe, going lower is not. Over time, the dielectric material inside a run capacitor breaks down from heat cycling and electrical stress, causing it to lose capacitance or fail outright. A failing dual capacitor produces a very recognizable set of symptoms: the outdoor unit hums but the compressor or fan won't start, the fan spins slowly or needs a manual push to get going, the system trips the breaker, or the capacitor can itself is visibly bulging, domed, or leaking oily residue at the top. Quick Answer The XPARTCO XPDC40X5-450R Dual Run Capacitor fixes central air conditioners and heat pumps where the outdoor unit hums but won't start, the compressor or fan motor won't run, the fan spins slowly or needs a manual push, the breaker trips, or the capacitor can is visibly bulged or leaking. 40 MFD (compressor) + 5 MFD (fan) dual capacitor, 450VAC, round, 3-terminal. Universal fit for equipment originally speced at 370V or 440V, since a higher voltage rating is always a safe upgrade. Capacitors store a dangerous electrical charge even after power is disconnected — always discharge before handling. Common Problems This Part Fixes Outdoor AC unit hums but the compressor won't start Condenser fan won't spin, or spins slowly and needs a manual push to get going System trips the breaker shortly after starting AC blows warm air because the compressor isn't running Repeated clicking sound from the contactor as it tries and fails to start the motor Capacitor can visibly bulging, domed on top, or leaking oily residue System that used to start slowly and has now stopped starting altogether Burning smell from the outdoor unit's electrical compartment Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers XPDC40X5-450R This is a universal component rather than a single-manufacturer part, so the specific OEM number your HVAC system's label references will vary by brand (Goodman, Trane, Carrier, Rheem, York, Lennox, Amana, and others). This capacitor is a correct replacement for any dual run capacitor matching the 40 MFD / 5 MFD rating with a voltage rating of 450V or lower. If you have your original part number, contact our support team and we will verify compatibility before you order. Compatibility This dual run capacitor is a universal replacement compatible with central air conditioners, heat pumps, and condensing units across all major HVAC brands, wherever the original capacitor is rated: 40 MFD (compressor) + 5 MFD (fan motor) 370V, 440V, or 450V (this capacitor's 450V rating exceeds and safely replaces either lower rating) Round can shape with 3 terminals Note: The MFD (microfarad) rating must match your original capacitor exactly on both sides — do not substitute a different MFD value for either the compressor or fan side. Voltage rating, on the other hand, can be equal to or higher than the original (450V safely replaces 370V or 440V), but never lower. Can shape (round vs. oval) affects only physical fit inside your unit's electrical compartment, not performance. If you're unsure of your original capacitor's specifications, they're printed directly on its can — contact our support team if you'd like help confirming compatibility. Key Features Universal dual run capacitor — supports both the compressor and condenser fan motor from one component 40 MFD compressor rating + 5 MFD fan motor rating in a single 3-terminal can 450VAC rating — a safe upgrade replacement for equipment originally speced at 370V or 440V Round aluminum can construction Resolves "hums but won't start," "fan spins slowly," "trips the breaker," and "bulging or leaking can" symptoms caused by capacitor failure 1/4" quick-connect terminals for a direct plug-on fit to standard HVAC wiring 50/60Hz rated Safety approved: CQC, VDE, TÜV, and CL; built to GB/T 3667 and EN 60252 standards Built to meet or exceed industry-standard specifications for this capacitor class Product Specifications Part Number XPDC40X5-450R Part Type Dual Run Capacitor Condition New — Universal Replacement Part Capacitance — Compressor 40 MFD (µF) Capacitance — Fan Motor 5 MFD (µF) Voltage Rating 450VAC Shape Round Terminals 3 (1/4" quick-connect) Frequency 50/60 Hz Tolerance ±5% Construction Type Polypropylene film capacitor Operating Temperature Range -40°C to 70°C (-40°F to +158°F) Safety Approvals CQC, VDE, TÜV, CL Approval Standard GB/T 3667, EN 60252 Application Central Air Conditioners, Heat Pumps, Condensing Units Quantity 1 dual run capacitor Compatible Brands Universal — all major HVAC brands Installation Notes ⚠️ Danger — Capacitors Store A Dangerous Electrical Charge Shut off power to the outdoor unit at the disconnect box and at the breaker before beginning. A capacitor stores an electrical charge even after power has been disconnected, and that charge can deliver a serious or fatal shock. Before touching any terminal, discharge the capacitor by shorting each pair of terminals together (C-to-Fan, C-to-Herm, and Fan-to-Herm) using an insulated-handle screwdriver, or by using a proper capacitor discharge tool with a resistor. Never short the terminals with a bare metal tool held with your bare hand. If you are not fully comfortable performing a capacitor discharge safely, have a qualified HVAC technician replace this part instead. ⚠️ Photograph The Wiring Before Disconnecting — Match Terminals Exactly Wear work gloves and safety glasses. After confirming the capacitor is fully discharged, photograph the wiring on the old capacitor's terminals before disconnecting anything — dual capacitors are labeled C (Common), Herm or Comp (compressor/hermetic), and Fan, and getting a wire on the wrong terminal can damage the new capacitor or the motor it feeds. Note which terminal each wire came from, or label them individually with tape. Remove the mounting strap or bracket holding the old capacitor in its housing, and disconnect each wire from its terminal. Install the new XPDC40X5-450R in the same mounting position, secure it with the strap or bracket, and reconnect each wire to the matching terminal (C, Herm, and Fan) exactly as labeled. Double-check every connection before restoring power. Restore power at the breaker and disconnect box, and confirm the compressor and fan both start promptly and run smoothly. Tools needed: insulated-handle screwdriver or capacitor discharge tool, nut driver, work gloves, safety glasses. Frequently Asked Questions My AC unit hums but won't start. Is this the capacitor? It's one of the most common causes of exactly that symptom. A run capacitor gives the compressor or fan motor the extra push needed to start turning; without it, the motor can draw power and hum in place without ever actually starting to spin. If you can see the capacitor can and it looks bulged, domed on top, or is leaking a brown oily residue, that's strong visual confirmation of failure. Can I use a 450V capacitor to replace my old 370V or 440V one? Yes. Voltage rating is a ceiling, not an exact match requirement — a capacitor rated for a higher voltage than your original will work safely and often lasts longer under the same electrical stress. What you cannot do is go the other direction: never install a capacitor with a lower voltage rating than your original, since that risks premature failure or the capacitor breaking down under normal operating conditions. Does the round vs. oval shape matter? Only for physical fit inside your unit's electrical compartment — it has no effect on electrical performance. If your unit's mounting bracket or available space is sized for a round can, use a round capacitor; if it's sized for an oval can, use an oval one. The MFD and voltage ratings are what matter electrically, not the shape. The fan spins if I give it a push, but won't start on its own. What does that mean? This is a classic sign of a weak or failing capacitor — it may still have enough charge to keep the motor running once it's already spinning, but not enough to provide the initial starting torque. This is a strong signal to replace the capacitor before it fails completely and leaves you with no cooling at all. Is this a genuine OEM part? This is a universal replacement part rather than a brand-specific OEM part. Because dual run capacitors are a standardized component defined by their electrical specifications rather than their manufacturer, this capacitor is a correct replacement for any unit's original capacitor that shares the same 40/5 MFD, 450VAC, round dual run capacitor rating — regardless of which HVAC brand originally installed it. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Replacement Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WR49X25197 Refrigerator Genuine OEM Axial Evaporator Motor Replaces WR60X26866 The WR49X25197 is a genuine GE OEM axial evaporator fan motor for the fresh food evaporator on select GE French door refrigerators. Unlike a standard evaporator fan motor, this is an axial-design motor purpose-built for the fresh food side of the refrigeration system, using its blade geometry to move air efficiently and quietly through that compartment's evaporator coil for precise, consistent temperature control. Rated 13.6VDC, 0.16A. Manufactured by Nidec, designation V80E14MS2A3-57A611. Over time, motor bearings wear out or the motor can fail electrically, and symptoms typically include the fresh food compartment running warm while the freezer remains unaffected, unusual noise from the fresh food evaporator area, or inconsistent cooling in that compartment specifically, since this motor doesn't serve the freezer side at all. It directly replaces WR60X26866, WR60X10341, WR60X24303, WR60X26033, WR60X10356, WR60X10357, WR60X26030, 239D1412P001, 239D1412P006, and AP6278228. Quick Answer The WR49X25197 Genuine OEM GE Axial Evaporator Motor fixes GE French door refrigerators where the fresh food compartment specifically runs warm, there's unusual noise from the fresh food evaporator area, or fresh food cooling is inconsistent while the freezer works fine. 13.6VDC, 0.16A axial motor. Replaces WR60X26866, WR60X10341, WR60X24303, WR60X26033, WR60X10356, WR60X10357, WR60X26030, 239D1412P001, 239D1412P006, AP6278228. If your refrigerator was manufactured between May 2014 and March 2015 (serial range HD–FF), the control software must also be updated by factory service or a Software Update Module (WR98R882802) for this motor to perform correctly. Common Problems This Part Fixes Fresh food compartment running warm while the freezer stays normal Unusual noise coming from the fresh food evaporator area Inconsistent or fluctuating temperature in the fresh food section specifically Fresh food evaporator fan not spinning or spinning intermittently Reduced airflow affecting fresh food cooling performance Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator axial evaporator motor directly replaces the following OEM and cross-reference part numbers: WR49X25197, WR60X26866, WR02X13733, WR60X10341, WR60X10356, WR60X10357, WR60X24303, WR60X26030, WR60X26033, V80E14MS2A3-57A611, 8817V W1, 239D1412P006, PD00038765, FIX12172983, AGE29673, AP6278228, PS12172983 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This axial evaporator motor is compatible with select GE French door refrigerators. Note — fresh food evaporator only, and a software caveat for certain units: This motor serves the fresh food evaporator specifically — a different application from a general freezer evaporator fan motor. Additionally, if your refrigerator was manufactured between May 2014 and March 2015 (serial range HD through FF), the refrigerator's control software must be updated by factory service, or with a Software Update Module (WR98R882802), for this motor to perform correctly after installation. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified axial blade design for the fresh food evaporator Resolves "fresh food running warm," "unusual noise from the fresh food evaporator," and "inconsistent fresh food cooling" symptoms Rated 13.6VDC, 0.16A Manufactured by Nidec, designation V80E14MS2A3-57A611 Direct drop-in replacement matching the original mounting and blade fitment Replaces WR60X26866, WR60X10341, WR60X24303, WR60X26033, WR60X10356, WR60X10357, WR60X26030, 239D1412P001, 239D1412P006, and AP6278228 Compatible with GE French door refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WR49X25197 OEM Part Number WR60X26866 Part Type Axial Evaporator Fan Motor (Fresh Food) Condition Genuine OEM Brand GE Application French Door Refrigerators — Fresh Food Evaporator Voltage 13.6VDC Amperage 0.16A Motor Manufacturer Nidec (V80E14MS2A3-57A611) Motor Type Axial Software Update Caveat Required for units mfg. May 2014–March 2015, serial range HD–FF (WR98R882802) Quantity 1 evaporator motor Compatible Brand GE Installation Notes ⚠️ Unplug Refrigerator Before Starting — Check Your Manufacture Date For A Software Update Requirement Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. Before starting, check your refrigerator's serial number/manufacture date sticker (typically inside the fresh food compartment) — if your unit was made between May 2014 and March 2015 with a serial range of HD through FF, plan for a control software update via factory service or a Software Update Module (WR98R882802) after installing this motor, since without it the new motor may not perform correctly. Access to the fresh food evaporator is typically through an interior panel in the fresh food compartment, separate from the freezer's evaporator access — check your model's service diagram. If there's frost or ice buildup around the fan or coil, let the unit sit unplugged with the door open for a few hours before continuing. Photograph the wiring harness connector and the fan blade's orientation before disconnecting anything. Unplug the wiring harness connector from the old motor, remove the mounting screws or clips holding the motor bracket in place, and pull the motor and fan blade assembly free. Mount the new WR49X25197 in the same position, reconnect the wiring harness connector fully, and confirm the blade spins freely by hand without contacting the housing before reassembling the panel. Restore power and monitor the fresh food compartment over the next 24 hours to confirm even, consistent cooling has returned. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My fresh food section runs warm but the freezer is fine. Is this the right part? Yes, this is exactly the symptom pattern this motor addresses, since it's dedicated specifically to the fresh food evaporator rather than serving both compartments. If your freezer is cooling normally and only the fresh food section is warm or inconsistent, this axial motor is a strong candidate for the cause. Do I really need a software update after installing this motor? Only if your refrigerator falls into a specific manufacturing window: units made between May 2014 and March 2015, identifiable by a serial range of HD through FF. For those units, GE's own guidance states the control software must be updated by factory service or with a Software Update Module (WR98R882802) for the new motor to perform correctly. If your refrigerator falls outside that date range, this step isn't necessary — check your serial number sticker to confirm which category your unit falls into. Is this the same as a regular evaporator fan motor? Not quite — this is an axial-design motor built specifically for the fresh food evaporator on GE French door refrigerators, distinct from general evaporator fan motors that serve the freezer side or both compartments together. Always confirm your model number and which compartment's fan has failed before ordering. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original axial motor design, blade fitment, and electrical rating of the fresh food evaporator motor originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WR60X31997 Genuine OEM GE Refrigerator Ice Box Fan Motor The WR60X31997 is a genuine GE OEM ice box fan motor assembly for GE, Hotpoint, Haier, Monogram, and Café refrigerators. This motor is situated in the freezer section and circulates cold air specifically around the ice box area, playing a direct role in ice production as well as general cooling and airflow in that part of the freezer. Consistent airflow here is what keeps the ice maker producing normally and prevents warm spots from developing nearby. Rated 12V DC, 0.23A. Common causes of failure include a malfunctioning motor, worn-out bushings that hinder smooth rotation, or damaged fan blades that restrict airflow; mineral buildup can also gradually degrade the fan's efficiency over time. A failing ice box fan produces a recognizable set of symptoms: reduced or inadequate ice production, items in the freezer warming up or defrosting even with the door shut, unusual sounds or vibration when the fan runs, or uneven frost patterns suggesting the airflow in that area isn't circulating properly. It directly replaces PD00071430, 4964240, AP6978662, PS12744140, and EAP12744140. Quick Answer The WR60X31997 Genuine OEM GE Refrigerator Ice Box Fan Motor fixes GE, Hotpoint, Haier, Monogram, and Café refrigerators with reduced or inadequate ice production, freezer items warming up despite the door being shut, unusual fan noise or vibration, or uneven frost patterns. 12V DC, 0.23A. Replaces PD00071430, 4964240, AP6978662, PS12744140, EAP12744140. Common Problems This Part Fixes Reduced or inadequate ice production from the ice maker Items in the freezer warming up or partially defrosting even with the door shut Unusual sounds or vibrations coming from the ice box fan area Uneven frost patterns suggesting ineffective air circulation Fan blade that doesn't spin freely, or doesn't spin at all, when checked by hand Freezer running less efficiently overall near the ice box area Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator ice box fan motor directly replaces the following OEM and cross-reference part numbers: WR60X31997, 4964240, AP6978662, EAP12744140, Nidec Model G11I12MS1AZ-57, PS12744140, AGE29835, PD00071430 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This ice box fan motor is compatible with select GE refrigerators, and also fits select Hotpoint, Haier, Monogram, Café, Profile, Fisher & Paykel, and Kenmore/Sears refrigerators built on the GE platform, including model numbers such as CQE28DM5NBS5, CVE28DM5NBS5, CVE28DM5NCS5, and CVE28DM5NS5. Note: This is the ice box fan motor specifically, a different component from GE's general evaporator fan motors used elsewhere in the freezer. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which fan motor your refrigerator needs. Key Features Genuine GE OEM part — factory-specified motor and blade design Circulates cold air around the ice box area, supporting ice production and nearby cooling Resolves "inadequate ice production," "items warming up," "unusual noise," and "uneven frost" symptoms caused by fan motor failure Premium motor coil and quality bearings for smooth, low-noise operation Rated 12V DC, 0.23A Direct drop-in replacement matching the original mounting and blade fitment Replaces PD00071430, 4964240, AP6978662, PS12744140, and EAP12744140 Compatible with GE, Hotpoint, Haier, Monogram, Café, Profile, Fisher & Paykel, and Kenmore/Sears refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WR60X31997 Part Type Refrigerator Ice Box Fan Motor Assembly Condition Genuine OEM Brand GE Location Freezer section, ice box area Function Circulates cold air to support ice production and cooling near the ice box Voltage 12V DC Amperage 0.23 A Quantity 1 fan motor assembly Compatible Brands GE, Hotpoint, Haier, Monogram, Café, Profile, Fisher & Paykel, Kenmore/Sears Installation Notes ⚠️ Unplug Refrigerator Before Starting Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. Access the ice box fan by locating the panel or housing covering it in the freezer's ice box area — this may require removing the ice maker or nearby components for clearance depending on your model. Photograph the wiring and the fan blade's orientation before disconnecting anything. Disconnect the motor's wiring harness connector, remove the mounting screws or clips holding the motor bracket in place, and pull the motor and fan blade assembly free. Mount the new WR60X31997 in the same position, reconnect the wiring harness connector, and confirm the blade spins freely by hand without contacting the housing before reassembling any panels or components you removed for access. Restore power and monitor ice production and freezer temperature over the next 24 hours to confirm normal operation has returned. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My ice maker is producing less ice than usual. Could this fan be the cause? Yes, this is one of the more common symptoms of a failing ice box fan. Since this fan circulates cold air specifically around the ice box area, reduced airflow from a struggling or seized motor can directly slow down ice production, even if the rest of the freezer seems to be cooling normally. Items near the ice box seem to be warming up even though the freezer door is shut. Is that related? Yes. If this fan isn't circulating air properly, the area around the ice box can lose consistent cooling even while the rest of the freezer stays cold, since that zone depends specifically on this fan for airflow. This localized warming, paired with reduced ice production, is a strong combined signal pointing to this fan. Is this the same as a general evaporator fan motor? No, this is a distinct component. The ice box fan motor circulates air specifically around the ice box area to support ice production and nearby cooling, while a general evaporator fan motor circulates air across the evaporator coil for the freezer and fresh food compartments more broadly. The two serve different roles and are not interchangeable — always confirm which fan your model needs using your parts diagram or model number. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original motor design, blade fitment, and mounting configuration of the ice box fan motor originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

DA31-00103A Genuine OEM Refrigerator Condenser Fan Motor - Compatible with Samsung Product Description Ensure efficient cooling with the DA31-00103A Genuine OEM Refrigerator Condenser Fan Motor. This Samsung-manufactured motor is designed as a replacement for select Samsung refrigerators. It powers the fan to circulate air over the condenser coils, dissipating heat to maintain optimal refrigeration performance. This part addresses issues like insufficient cooling, frost buildup, unusual noises (e.g., chirping, buzzing), or the refrigerator running too frequently, often caused by a faulty or worn motor. Note: Includes (1) condenser fan motor (fan blade not included). Disconnect power before installation. Verify compatibility with your refrigerator model. Replaces part numbers: DA31-00103A, IS-27210SCD6A, PD00002207, EAP4138348m AP4140906, 1472692, PS4138348. Compatibility: Compatible with select Samsung refrigerator models, including but not limited to: Samsung: RS2631SL, RS2631SL/XAA, RS2623WW/XAA, RS2624SW, RS2624SW/XAA, RS2624WW, RS2631SW, RS2631SW/XAA, RSC5DBSH, RS2621SW/XAA, RS2623BB, RS2623BB/XAA, RS2623SH, RS2623SL, RS2623VQ, RS2630SH, RS2630WW Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Samsung refrigerators. 🔧 Specifications: Genuine OEM Samsung AC fan motor, 115V, 60Hz, 0.16A, 1300RPM, 1-5/8" shaft. 💪 Reliable Performance: Circulates air to dissipate heat from condenser coils for efficient cooling. 🛠️ Easy Installation: Requires screwdriver and pliers; typically installed in 15–30 minutes. 🛡️ Effective Fixes: Resolves insufficient cooling, frost buildup, noisy operation, or frequent running. Product Specification Part Number: DA31-00103A Component Type: Refrigerator condenser fan motor Material: Metal and plastic Electrical Specs: 115V, 60Hz, 0.16A, 1300RPM, 1-5/8" shaft, quick disconnect Compliance: UL-listed, Prop 65 warning for California. Installation Notes: Safety First: Disconnect the refrigerator from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your refrigerator cooling efficiently today! Add to cart now for a reliable fix!

Read more less

XPARTCO EAU63103201 Refrigerator Evaporator Fan Motor The XPARTCO EAU63103201 is an aftermarket replacement evaporator fan motor for LG and select Kenmore/Kenmore Elite refrigerators. On this platform, the fan sits behind a panel near the crisper drawers and circulates air specifically through the fresh food compartment — a different physical location than the freezer-mounted evaporator fans found on many other brands. When this motor slows down or fails, the fresh food section is the part of the refrigerator most directly affected, since it depends on this fan to keep cold air moving across the compartment. Rated 12V DC at 1A with a 4-pin connector, this motor has a 2.36" (60mm) shaft length and a 0.12" (3.16mm) shaft diameter, with roughly a 20.5" (56cm) wire lead. Common failure modes include worn motor bearings that let the blade wobble or bind, and general electrical wear from age. A fridge running warm, not cold at all, or making unusual noise from behind the crisper area are all signs pointing to this motor. It directly replaces 4391461, AP6317185, PS11761147, EAP11761147, and PD00051700. Also identified by its production number, ODM-001F-41. Quick Answer The XPARTCO EAU63103201 Refrigerator Evaporator Fan Motor fixes LG and select Kenmore/Kenmore Elite refrigerators where the fresh food compartment runs too warm or isn't cooling at all, or there's unusual noise from behind the crisper drawer area. DC 12V, 1A, 4-pin connector, 2.36" (60mm) shaft length, 0.12" (3.16mm) shaft diameter. Replaces 4391461, AP6317185, PS11761147, EAP11761147, PD00051700. LG uses several similarly-numbered EAU-prefix fan motors across its lineup — this is a different part from the EAU63923603/EAU65058305 assembly used on other LG models, so verify your exact model number before ordering. Common Problems This Part Fixes Fresh food compartment running too warm Refrigerator not cooling at all in the fresh food section Unusual noise coming from behind the crisper drawer area Fan motor that won't run due to aging or internal damage Refrigerator running constantly as it struggles to maintain temperature Fan blade that doesn't spin freely, or spins with noticeable resistance, when checked by hand Frost or condensation forming near the fan location behind the crisper panel Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator evaporator fan motor directly replaces the following OEM and cross-reference part numbers: EAU63103201, ODM-001F-41, 4391461, ALG1473540, AP6317185, PS11761147, OEM18086529, EAP11761147, PD00051700 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This evaporator fan motor is compatible with select LG refrigerators, and also fits select Kenmore and Kenmore Elite refrigerators built on the LG platform, including model numbers such as: LG LRSES2706V, LRSPS2706V LG LSXC22396D, LSXC22396S, LSXC22426S, LSXC22436S LG LSXC22486D, LSXC22486S LG LSXS26326B, LSXS26326S, LSXS26326W LG LSXS26336S, LSXS26336V, LSXS26336D LG LSXS26386S, LSXS26396S Kenmore 795.5173381, 795.5173781, 795.5183241, 795.5183242, 795.5183341, 795.5183941, 795.5183942, 795.5185361, 795.5185761, 795.5186261, 795.5186361, 795.5186761, 795.5186961 Note: LG uses several different evaporator fan motors across its refrigerator lineup with similar EAU-prefix part numbers. This EAU63103201 motor is a separate, distinct part from the EAU63923603 / EAU65058305 fan motor assembly used on other LG models (such as the LFXS28596S, LMXS28626S, LFXS26596S, and LFXS26973D series) — the two are not interchangeable. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which fan motor your refrigerator needs. Key Features Aftermarket replacement evaporator fan motor — circulates air through the fresh food compartment Resolves "fresh food too warm," "not cooling at all," and "noise behind the crisper drawer" symptoms caused by fan motor failure Rated 12V DC, 1A, with a 4-pin connector for direct plug-and-play electrical fit 2.36" (60mm) shaft length, 0.12" (3.16mm) shaft diameter Approximately 20.5" (56cm) wire lead Direct drop-in replacement matching the original mounting and blade fitment Replaces 4391461, AP6317185, PS11761147, EAP11761147, and PD00051700 Compatible with LG and select Kenmore/Kenmore Elite refrigerators Aftermarket replacement built to OEM-equivalent quality standards Straightforward DIY repair — just a screwdriver needed on most models Product Specifications Part Number XPEAU63103201 OEM Part Number EAU63103201 (ODM-001F-41) Part Type Refrigerator Evaporator Fan Motor Condition Aftermarket Replacement Compatible Brand LG, Kenmore Location Behind panel near the crisper drawers, fresh food compartment Voltage 12V DC Amperage 1 A Connector 4-pin Shaft Length 2.36 in. (60mm) Shaft Diameter 0.12 in. (3.16mm) Wire Lead Length Approx. 20.5 in. (56cm) Color Gray Material Plastic and metal Quantity 1 fan motor Compatible Brands LG, Kenmore, Kenmore Elite Installation Notes ⚠️ Unplug Refrigerator Before Starting Disconnect power at the outlet before beginning. Wear work gloves. Access on this platform is different from many other brands: rather than removing a rear panel inside the freezer, slide the crisper drawer out fully, then remove the panel behind or above the drawer area to expose the fan motor. Photograph the wiring connector and the fan blade's position before disconnecting anything. Disconnect the 4-pin electrical connector from the old motor, remove the mounting screws or clips holding the motor bracket in place, and carefully pull the motor and fan blade assembly free. Transfer the fan blade to the new motor if a blade isn't included, matching the original orientation on the 60mm shaft. Mount the new EAU63103201 in the same position, reconnect the 4-pin connector fully, and confirm the blade spins freely by hand without contacting the housing before reassembling the panel and sliding the crisper drawer back into place. Restore power and monitor the fresh food compartment over the next several hours to confirm normal cooling has returned. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions Why is this fan located near the crisper drawers instead of in the freezer? LG's refrigerator platform routes cold air to the fresh food compartment differently than many other brands, with this particular fan positioned behind a panel near the crisper drawer area rather than inside the freezer compartment. That's simply a difference in refrigerator design between manufacturers — it doesn't affect the fan's job, which is still to keep cold air circulating through the fresh food section, but it does mean the access point for this repair looks different from what you might expect if you've worked on a different brand before. My fridge section is warm but everything else seems fine. Is this the right part? Yes, this is the classic symptom this motor addresses. Since this fan specifically circulates air through the fresh food compartment, a failure here tends to affect that section directly — a warm fridge with an otherwise normally-functioning freezer points squarely at this motor rather than at the compressor or refrigerant system. There are several similar LG fan motor part numbers online. How do I know I have the right one? LG's EAU-prefix fan motors can look similar at a glance, but they aren't interchangeable — for example, the EAU63923603/EAU65058305 assembly used on models like the LFXS28596S and LMXS28626S is a completely different part from this EAU63103201 motor. The safest way to confirm is to check your refrigerator's full model number against a verified compatibility list, or contact our support team with your model number before ordering. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the electrical specifications (12V DC, 1A, 4-pin connector), shaft dimensions, and mounting configuration of the original EAU63103201 evaporator fan motor used in compatible LG and Kenmore refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

DA31-00146E Genuine OEM Refrigerator Evaporator Fan Motor - Compatible with Samsung, Maytag Product Description Maintain optimal cooling with the DA31-00146E Genuine OEM Refrigerator Evaporator Fan Motor. This Samsung-manufactured motor is designed as a replacement for select Samsung and Maytag refrigerators. It powers the fan to circulate air through the freezer and refrigerator compartments, ensuring even temperature distribution and efficient cooling. This part addresses issues like fridge/freezer too warm, frost buildup, unusual noises, or the appliance not shutting off, often caused by a faulty or seized motor. Note: Includes (1) evaporator fan motor (fan blade not included). Disconnect power before installation. Verify compatibility with your refrigerator model. Replaces part numbers: DA31-00146E, 1486536, DA31-00146G, DREP3020LA/HAL, PD00002015, AP4136569, PS4138376. Compatibility: Compatible with select refrigerator models, including but not limited to: Samsung: RFG238AABPXAA0000, RS25H5111BC/AA, RS265TDBP/XAA, RS267TDBP/XAA, RH25H5611BC/AA, RH25H5611WW/AA, DFSF9VKBABB, DFSS9VKBASS Maytag: Various models (verify with model number) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Samsung and Maytag refrigerators. 🔧 Specifications: Genuine OEM Samsung BLDC fan motor, 3.21W, 12VDC, 2520RPM, 1-1/2" shaft. 💪 Reliable Performance: Circulates air to maintain consistent temperatures and cool evaporator coils. 🛠️ Easy Installation: Requires screwdriver and pliers; typically installed in 30–60 minutes. 🛡️ Effective Fixes: Resolves warm fridge/freezer, frost buildup, noisy operation, or failure to shut off. Product Specification Part Number: DA31-00146E Component Type: Refrigerator evaporator fan motor Material: Metal and plastic Electrical Specs: 3.21W, 12VDC, 2520RPM, 1-1/2" shaft Compliance: UL-listed, Prop 65 warning for California Installation Notes: Safety First: Disconnect the refrigerator from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your refrigerator cooling efficiently today! Add to cart now for a reliable fix!

Read more less

EAU63923602 Refrigerator Condenser Fan Motor - Compatible with LG, Kenmore Refrigerators Product Description Restore your refrigerator’s cooling performance with the EAU63923602 Condenser Fan Motor. This replacement motor powers the condenser fan to dissipate heat from the coils, ensuring efficient cooling. Designed for select Kenmore, LG refrigerators, it fixes issues like poor cooling, freezer too warm, compressor overheating, or loud noises. Note: Includes one condenser fan motor. Take photos of wiring during disassembly and clean condenser coils before installation. Replaces part numbers: EAU63923602, ODM-001F-4B, PD00057884, EAP12383670, AP6317196, 4877338, PS12383670. Key Features: ✅ Brand Compatibility: Fits select LG, Kenmore refrigerator models. ❄️ Specifications: Condenser fan motor, 12V DC, 1A. 💰 Cost-Effective: OEM performance at a competitive price. 🛠️ Easy Installation: Requires a screwdriver, pliers, work gloves; typically installed in 20–40 minutes. 🛡️ Reliable Fixes: Resolves poor cooling, freezer too warm, compressor overheating, or noisy operation. Installation Notes: Safety First: Unplug the refrigerator before installation to avoid electrical shock. Clean condenser coils to ensure optimal performance. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your refrigerator running efficiently today! Add to cart now for a budget-friendly fix!

Read more less

809069207 Refrigerator Genuine OEM Evaporator Fan Motor – Compatible with Frigidaire, Electrolux, and Kenmore Refrigerators Product Description Restore powerful and consistent cooling with the 809069207 Refrigerator Genuine OEM Evaporator Fan Motor. This factory-approved motor circulates cold air throughout the refrigerator and freezer compartments, ensuring even temperature distribution. A failing fan motor can cause warm spots, frost buildup, poor cooling, or unusual noises. Replacing it with this Genuine OEM part ensures dependable performance and the same airflow efficiency your appliance had when new. Replaces Part Numbers 809069207, PD00064424, EAP12705983, AP6834878, PS12705983. Compatibility This Genuine OEM evaporator fan motor fits select Frigidaire, Electrolux, and Kenmore refrigerators. Example compatible models include (but are not limited to):Frigidaire FFHS2622MB3, FFSS2615TS0, Electrolux EI23CS55GS1, and Kenmore 253.7031321A. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🧩 Genuine OEM Replacement – Factory-certified for perfect fit and long-lasting performance ❄️ Restores Air Circulation – Ensures even cooling in fresh food and freezer sections 🔇 Quiet Motor Operation – Balanced OEM motor design lowers noise and vibration 💪 High Durability – Built with premium materials for extended service life 🛡️ Fixes Common Issues – Solves poor cooling, frost buildup, noisy fan, or warm temperatures 📐 Product Specification Part Number: 809069207 Component Type: Refrigerator Evaporator Fan Motor Material: Reinforced plastic fan housing with factory motor Voltage: 115V AC (model dependent) Mounting: Direct-fit motor mounted behind freezer interior panel Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the refrigerator before servicing to avoid electrical shock. Steps: Disconnect power and remove freezer shelves and panels. Locate the evaporator fan assembly. Disconnect the wiring harness and remove the old motor. Install the new 809069207 motor in the same location. Reassemble interior panels and restore power. Allow several minutes for airflow to stabilize. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Genuine OEM Replacement Part 🔄 30-Day Return Policy Restore powerful, even cooling — Add to Cart Now for a factory-quality repair!

Read more less

XPARTCO XPDC45X5-450R Dual Run Capacitor (45/5 MFD, 450V, Round) The XPARTCO XPDC45X5-450R is a universal dual run capacitor for central air conditioners, heat pumps, and condensing units. A run capacitor works alongside a single-phase AC motor to keep it running efficiently once it's started, boosting torque and correcting the phase of the current feeding the motor's windings. This is a dual capacitor, meaning it combines two separate capacitors — one for the compressor, one for the condenser fan motor — into a single three-terminal can, which is why nearly every residential outdoor AC unit uses exactly this style of component to run both motors from one part. Rated 45 MFD for the compressor circuit and 5 MFD for the fan motor circuit, at 450VAC, in a round aluminum can housing. Because a capacitor's voltage rating is a ceiling rather than a fixed match, this 450V-rated capacitor can safely replace an original capacitor rated 370V or 440V — going higher on voltage is always safe, going lower is not. Over time, the dielectric material inside a run capacitor breaks down from heat cycling and electrical stress, causing it to lose capacitance or fail outright. A failing dual capacitor produces a very recognizable set of symptoms: the outdoor unit hums but the compressor or fan won't start, the fan spins slowly or needs a manual push to get going, the system trips the breaker, or the capacitor can itself is visibly bulging, domed, or leaking oily residue at the top. Quick Answer The XPARTCO XPDC45X5-450R Dual Run Capacitor fixes central air conditioners and heat pumps where the outdoor unit hums but won't start, the compressor or fan motor won't run, the fan spins slowly or needs a manual push, the breaker trips, or the capacitor can is visibly bulged or leaking. 45 MFD (compressor) + 5 MFD (fan) dual capacitor, 450VAC, round, 3-terminal. Universal fit for equipment originally speced at 370V or 440V, since a higher voltage rating is always a safe upgrade. Capacitors store a dangerous electrical charge even after power is disconnected — always discharge before handling. Common Problems This Part Fixes Outdoor AC unit hums but the compressor won't start Condenser fan won't spin, or spins slowly and needs a manual push to get going System trips the breaker shortly after starting AC blows warm air because the compressor isn't running Repeated clicking sound from the contactor as it tries and fails to start the motor Capacitor can visibly bulging, domed on top, or leaking oily residue System that used to start slowly and has now stopped starting altogether Burning smell from the outdoor unit's electrical compartment Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers XPDC45X5-450R This is a universal component rather than a single-manufacturer part, so the specific OEM number your HVAC system's label references will vary by brand (Goodman, Trane, Carrier, Rheem, York, Lennox, Amana, and others). This capacitor is a correct replacement for any dual run capacitor matching the 45 MFD / 5 MFD rating with a voltage rating of 450V or lower. If you have your original part number, contact our support team and we will verify compatibility before you order. Compatibility This dual run capacitor is a universal replacement compatible with central air conditioners, heat pumps, and condensing units across all major HVAC brands, wherever the original capacitor is rated: 45 MFD (compressor) + 5 MFD (fan motor) 370V, 440V, or 450V (this capacitor's 450V rating exceeds and safely replaces either lower rating) Round can shape with 3 terminals Note: The MFD (microfarad) rating must match your original capacitor exactly on both sides — do not substitute a different MFD value for either the compressor or fan side. Voltage rating, on the other hand, can be equal to or higher than the original (450V safely replaces 370V or 440V), but never lower. Can shape (round vs. oval) affects only physical fit inside your unit's electrical compartment, not performance. If you're unsure of your original capacitor's specifications, they're printed directly on its can — contact our support team if you'd like help confirming compatibility. Key Features Universal dual run capacitor — supports both the compressor and condenser fan motor from one component 45 MFD compressor rating + 5 MFD fan motor rating in a single 3-terminal can 450VAC rating — a safe upgrade replacement for equipment originally speced at 370V or 440V Round aluminum can construction Resolves "hums but won't start," "fan spins slowly," "trips the breaker," and "bulging or leaking can" symptoms caused by capacitor failure 1/4" quick-connect terminals for a direct plug-on fit to standard HVAC wiring 50/60Hz rated Safety approved: CQC, VDE, TÜV, and CL; built to GB/T 3667 and EN 60252 standards Built to meet or exceed industry-standard specifications for this capacitor class Product Specifications Part Number XPDC45X5-450R Part Type Dual Run Capacitor Condition New — Universal Replacement Part Capacitance — Compressor 45 MFD (µF) Capacitance — Fan Motor 5 MFD (µF) Voltage Rating 450VAC Shape Round Terminals 3 (1/4" quick-connect) Frequency 50/60 Hz Tolerance ±5% Construction Type Polypropylene film capacitor Operating Temperature Range -40°C to 70°C (-40°F to +158°F) Safety Approvals CQC, VDE, TÜV, CL Approval Standard GB/T 3667, EN 60252 Application Central Air Conditioners, Heat Pumps, Condensing Units Quantity 1 dual run capacitor Compatible Brands Universal — all major HVAC brands Installation Notes ⚠️ Danger — Capacitors Store A Dangerous Electrical Charge Shut off power to the outdoor unit at the disconnect box and at the breaker before beginning. A capacitor stores an electrical charge even after power has been disconnected, and that charge can deliver a serious or fatal shock. Before touching any terminal, discharge the capacitor by shorting each pair of terminals together (C-to-Fan, C-to-Herm, and Fan-to-Herm) using an insulated-handle screwdriver, or by using a proper capacitor discharge tool with a resistor. Never short the terminals with a bare metal tool held with your bare hand. If you are not fully comfortable performing a capacitor discharge safely, have a qualified HVAC technician replace this part instead. ⚠️ Photograph The Wiring Before Disconnecting — Match Terminals Exactly Wear work gloves and safety glasses. After confirming the capacitor is fully discharged, photograph the wiring on the old capacitor's terminals before disconnecting anything — dual capacitors are labeled C (Common), Herm or Comp (compressor/hermetic), and Fan, and getting a wire on the wrong terminal can damage the new capacitor or the motor it feeds. Note which terminal each wire came from, or label them individually with tape. Remove the mounting strap or bracket holding the old capacitor in its housing, and disconnect each wire from its terminal. Install the new XPDC45X5-450R in the same mounting position, secure it with the strap or bracket, and reconnect each wire to the matching terminal (C, Herm, and Fan) exactly as labeled. Double-check every connection before restoring power. Restore power at the breaker and disconnect box, and confirm the compressor and fan both start promptly and run smoothly. Tools needed: insulated-handle screwdriver or capacitor discharge tool, nut driver, work gloves, safety glasses. Frequently Asked Questions My AC unit hums but won't start. Is this the capacitor? It's one of the most common causes of exactly that symptom. A run capacitor gives the compressor or fan motor the extra push needed to start turning; without it, the motor can draw power and hum in place without ever actually starting to spin. If you can see the capacitor can and it looks bulged, domed on top, or is leaking a brown oily residue, that's strong visual confirmation of failure. Can I use a 450V capacitor to replace my old 370V or 440V one? Yes. Voltage rating is a ceiling, not an exact match requirement — a capacitor rated for a higher voltage than your original will work safely and often lasts longer under the same electrical stress. What you cannot do is go the other direction: never install a capacitor with a lower voltage rating than your original, since that risks premature failure or the capacitor breaking down under normal operating conditions. Does the round vs. oval shape matter? Only for physical fit inside your unit's electrical compartment — it has no effect on electrical performance. If your unit's mounting bracket or available space is sized for a round can, use a round capacitor; if it's sized for an oval can, use an oval one. The MFD and voltage ratings are what matter electrically, not the shape. The fan spins if I give it a push, but won't start on its own. What does that mean? This is a classic sign of a weak or failing capacitor — it may still have enough charge to keep the motor running once it's already spinning, but not enough to provide the initial starting torque. This is a strong signal to replace the capacitor before it fails completely and leaves you with no cooling at all. Is this a genuine OEM part? This is a universal replacement part rather than a brand-specific OEM part. Because dual run capacitors are a standardized component defined by their electrical specifications rather than their manufacturer, this capacitor is a correct replacement for any unit's original capacitor that shares the same 45/5 MFD, 450VAC, round dual run capacitor rating — regardless of which HVAC brand originally installed it. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Replacement Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 4681JB1029A Refrigerator Evaporator Fan Motor – Compatible with LG and Kenmore Refrigerators Product Description Keep your refrigerator cooling evenly with the XPARTCO 4681JB1029A Refrigerator Evaporator Fan Motor. This Fan Motor is a replacement component for specific LG, Kenmore refrigerator models. It operates the circulation fan located in the back of the refrigerator compartment, distributing cool air evenly throughout. The motor enables constant airflow across shelves and compartments to maintain consistent temperatures and humidity levels. Causes of a bad fan motor include failure of bearings or windings due to prolonged use. Replaces Part Numbers 4681JB1029A, EAU60694507, 1330410, 4681JB1010C, 4681JB1017A, 4681JB1017D, 4681JB1027A, EAU61762902, EAU41921810, PD00037982, EAP3523328, AH3523328, EA3523328, AP4438221, PS3523328.  Compatibility This replacement evaporator fan motor fits select LG and Kenmore refrigerators. Example compatible models include (but are not limited to): LG LFX25960ST, LG LFX28968ST, and Kenmore 795.77543600. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Built to meet OEM airflow and reliability standards ❄️ Efficient Air Circulation – Distributes cold air evenly through refrigerator and freezer 💰 Affordable Solution – Quality replacement at a lower cost than OEM parts 🛠️ DIY Installation – Simple plug-in wiring connector for quick installation 🛡️ Fixes Common Issues – Solves frost buildup, uneven cooling, or noisy fan problems 📐 Product Specification Part Number: 4681JB1029A Component Type: Refrigerator Evaporator Fan Motor Material: Metal motor housing with balanced plastic fan blade Mounting: Direct-fit replacement in freezer evaporator compartment Operating Conditions: Designed for continuous low-temperature operation Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the refrigerator before performing repairs to prevent electrical shock. Steps: Unplug the refrigerator. Remove shelves and freezer rear panel to access the evaporator area. Disconnect the wiring harness and mounting screws on the old fan motor. Install the new XPARTCO 4681JB1029A motor, reconnect wiring, and secure the panel. Restore power and verify quiet, consistent airflow. ⏱️ Time Required: 20–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore efficient, even cooling — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

DA97-15765C Refrigerator Genuine OEM Condenser Fan Motor Replaces Part Numbers: DA97-15765C, DA97-15765A, DA97-12842A, DA97-12842B, DA97-12842D, DA97-15765D, AP6001015, PS11733650. Description: This Refrigerator Condenser Fan Motor Assembly is an essential component designed to maintain optimal cooling performance in select Samsung refrigerator models. This Genuine OEM part ensures reliable operation by efficiently circulating air through the condenser coils, preventing overheating and maintaining consistent temperatures.

Read more less

809069201 Refrigerator Genuine OEM Evaporator Fan Motor Fits specific Frigidaire, Electrolux refrigerator models. Description: This Evaporator Fan Motor is an OEM part for specific Frigidaire refrigerator models. It circulates air over the evaporator coils and throughout the refrigerator and freezer compartments, ensuring even cooling and maintaining the desired temperatures. Replaces Part Numbers:809069206, 809069201, AP7014188, PS16544514. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less