Search results for "tub seals"

MDS66290824 Genuine OEM Washer Door Gasket The Genuine OEM MDS66290824 is a factory-original door boot gasket manufactured by LG for use in LG front-load washers and washer-dryer combo units. The gasket forms the watertight seal between the door, cabinet, and tub, flexing with every door open/close cycle while keeping wash water contained inside the drum. As the rubber ages, it commonly cracks, tears, or develops mold/mildew buildup in its folds, and a compromised seal leads directly to water leaking out around the door during the wash or spin cycle. This is a current-production part: MDS66290824. As the genuine LG part, it ships in factory black rubber matching the original color, fold pattern, and mounting groove, so it seats and seals exactly like the original. Quick Answer The Genuine OEM MDS66290824 Washer Door Gasket fixes LG front-load washers and washer-dryer combo units that leak water around the door, or that have a cracked, torn, or moldy door boot seal. Classic symptom: water pooling on the floor in front of the washer after a cycle, with visible cracking or gaps in the door seal. Common Problems This Part Fixes Water leaking from around the door during the wash or spin cycle Visible cracks, tears, or splits in the door boot rubber Mold or mildew buildup trapped in the gasket folds that won't clean out Door boot pulling away from its mounting groove on the cabinet or tub Musty odor coming from the washer even after cleaning Door won't seal fully closed due to a warped or damaged gasket Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door gasket directly replaces the following OEM and cross-reference part numbers: MDS66290824, 4963077, 4981902, AP6993434, ALG55389, AP7212758, EAP16224172, EAP16879236, PD00084356, PS16224172, PS16879236.  If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door gasket is compatible with select LG front-load washers and washer-dryer combo units, including: LG W3S1CVK2EHM, W3S1CVK2ENS, W3S1CVK2EVS, W3S1CVK2RNS, W3S1CVK2RVS LG WKEX200HBA, WKEX200HGA, WKEX200HWA LG WKGX201HBA, WKGX201HGA, WKGX201HWA LG WM4500HBA, WM5500HVA, WM5700HVA LG F3S1CWK2WN and related WashTower/combo dryer units sharing this door assembly Note: If your parts diagram or old part still shows MDS66290803, this current MDS66290824 gasket is the correct replacement — the earlier revision has been superseded and is no longer produced new. Always verify your appliance model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine LG OEM door boot gasket — factory-original fit, seal, and color match Resolves "leaking around the door," "cracked/torn boot," and "moldy seal" symptoms Current production part — supersedes the earlier MDS66290803 revision Black rubber construction matching original factory appearance Approximately 13"W x 15"L x 10"H, ~3 lb 1 oz Replaces MDS66290824, MDS66290803, 4963077, 4981902, AP6993434, ALG55389, AP7212758, EAP16224172, EAP16879236, PD00084356, PS16224172, PS16879236 Compatible with select LG front-load washers and washer-dryer combo units Genuine OEM part — factory-specified rubber compound and mounting groove fit Product Specifications Part Number MDS66290824 OEM Part Number MDS66290824 Part Type Washer Door Boot Gasket Condition Genuine OEM Replacement Color Black Material Rubber/elastomer gasket seal Dimensions Approx. 13"W x 15"L x 10"H Weight Approx. 3 lb 1 oz Compatible Brand LG Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power before beginning. Open the door and locate the large outer retaining band (spring clamp) holding the gasket to the front cabinet panel — release it with pliers or a flat-blade screwdriver and pull the gasket's outer lip free from the cabinet opening. Working around the boot, fold the gasket into the drum opening to access the inner retaining band securing it to the tub; release this band as well and remove the old gasket. Check for and transfer any small parts such as the drain/pressure sensor port fitting if your model routes one through the boot. Fit the new MDS66290824 gasket's inner lip into the tub-side mounting groove first, working it evenly around the full circumference, then reinstall the inner retaining band. Fold the gasket back out and seat the outer lip into the cabinet opening, aligning it evenly, then reinstall the outer retaining band. Restore power and run a cycle with the door closed to check for leaks around the full perimeter of the seal. Tools needed: pliers or a flat-blade screwdriver, and a spring clamp tool if your model uses a wire-spring outer band. Frequently Asked Questions Is MDS66290824 the same as MDS66290803? MDS66290824 is the current genuine LG gasket, and it supersedes the earlier MDS66290803 revision, which is no longer produced new. If your washer's parts diagram or old gasket shows MDS66290803, this MDS66290824 is the correct current replacement — LG has updated the part number but the fit and function for your model remain the same. My washer is leaking water from the door — is this the part I need? In most cases, yes. A worn, cracked, or torn door boot gasket is the most common cause of water leaking around the door on a front-load washer. Inspect the gasket's folds closely for splits or debris (coins, small items) caught in the seal, since a foreign object trapped in the boot can also prevent a full seal without the gasket itself being damaged. Do I need to transfer any parts from my old gasket? Check whether your model routes a drain hose fitting, pressure sensor port, or door lock striker through the boot itself. If so, that fitting typically transfers from the old gasket to the new one, or is a separate reusable part — inspect your old gasket carefully before disposal in case a component needs to be moved over. Can I clean mold out of the gasket instead of replacing it? Light surface mold can often be cleaned with a diluted bleach or vinegar solution and a soft brush, and running the washer's tub-clean cycle regularly helps prevent it from returning. However, if mold has caused the rubber to degrade, crack, or lose its seal, cleaning won't restore a proper watertight fit — replacement is the reliable fix once the gasket itself is damaged. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine LG OEM Part ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

A00126401 Genuine OEM Frigidaire Dishwasher Drain Pump Motor The A00126401 is a genuine Frigidaire OEM drain pump motor assembly for Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, and Kenmore dishwashers. At the end of each wash cycle, this pump is what actually pushes the used wash water out of the tub and through the drain hose, clearing the way for the next fill. An internal impeller spins to create that flow, drawing water in and forcing it out through the drain line. Rated 120V, 60Hz, 35W, 0.8A, 3600RPM, with 1/4" male terminals, this assembly includes the pump motor, impeller, and seal. Common causes of failure include clogs from food particles or debris interfering with the impeller, worn or damaged impeller blades, and electrical failure of the motor itself. A failing drain pump typically shows up as water not draining from the dishwasher, water pooling at the bottom of the tub after a cycle, a grinding or humming noise from the pump area, or the dishwasher refusing to start a new cycle because it detects standing water left over from the last one. It directly replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, and EAP2363535. Quick Answer The A00126401 Genuine OEM Frigidaire Dishwasher Drain Pump Motor fixes Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, and Kenmore dishwashers that won't drain, pool water at the bottom of the tub, make grinding or humming noises, or won't start a new cycle due to leftover water. 120V, 60Hz, 35W, 0.8A, 3600RPM. Replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, EAP2363535. Before replacing the pump, check the drain hose and sump screen for a simple clog — one customer replaced the pump, still had no drainage, and found a clogged drain hose was the actual cause. Common Problems This Part Fixes Dishwasher won't drain at the end of the cycle Water pooling at the bottom of the tub after a completed cycle Grinding or humming noise coming from the pump area Dishwasher won't start a new cycle because it detects leftover water from the previous one Dishes not getting properly cleaned due to poor water circulation Pump running but producing little or no actual drainage Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers: A00126401, 154736201, 3015405, 5304492415, PD00000922, EAP2363535, AFR20557, AP5690431, PS8689824 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Frigidaire dishwashers, and also fits select Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, and Kenmore/Sears dishwashers built on the same platform. Note: This assembly includes the pump motor, impeller, and seal. Whether a check valve flapper is included can vary by supplier batch — inspect your old pump's flapper condition before assuming one is included, and contact our support team if you need to confirm. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified motor speed and impeller design Pumps water out of the tub and through the drain hose at the end of each cycle Resolves "won't drain," "water pooling," "grinding or humming noise," and "won't start due to leftover water" symptoms caused by pump failure Includes pump motor, impeller, and seal Rated 120V, 60Hz, 35W, 0.8A, 3600RPM 1/4" male terminals for a direct plug-in electrical fit Direct drop-in replacement — no modification required Replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, and EAP2363535 Compatible with Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, and Kenmore dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number A00126401 Part Type Dishwasher Drain Pump Motor Assembly Condition Genuine OEM Brand Frigidaire Voltage 120V Frequency 60 Hz Wattage 35 W Amperage 0.8 A Motor Speed 3600 RPM Terminals 1/4" male Kit Contents Pump motor, impeller, seal Dimensions Approx. 3-1/4"L x 2-1/2"W x 3-3/4"H Color White / Green Repair Difficulty Easy to Moderate — under an hour Quantity 1 drain pump motor assembly Compatible Brands Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, Kenmore Installation Notes ⚠️ Unplug Dishwasher Before Starting — Rule Out A Simple Clog First Before replacing the pump, check the drain hose and the sump screen at the bottom of the tub for a clog — food debris and buildup in the hose can produce identical "won't drain" symptoms to a failed pump, and clearing a clog costs nothing but a few minutes. One customer replaced the pump entirely, still had no drainage, and only afterward discovered the actual cause was a clogged drain hose; disconnecting and running a cycle without the hose attached can help confirm whether the pump itself is pushing water. Once you've confirmed the pump needs replacing, disconnect power at the outlet or shut off the circuit breaker, and pull the dishwasher out from under the counter for access to the underside — removing the two screws securing it to the counter first. Have a drain pan or towels ready for residual water. Photograph the wiring and hose connections before disconnecting anything. Disconnect the two wire connectors from the old pump, remove the three screws securing it in place, and disconnect the hose connections, then pull the old pump free. Install the new A00126401 in the same position, reconnect the hose connections, and reconnect the two wire connectors. Secure the pump with its three mounting screws. Slide the dishwasher back into place and secure it to the counter, restore power, and run a full test cycle to confirm normal draining with no leaks or unusual noise. Tools needed: Phillips screwdriver, flat-blade screwdriver, needle-nose pliers, drain pan, work gloves. Frequently Asked Questions My dishwasher won't drain. How do I know if it's actually the pump and not something simpler? Check the drain hose and the sump screen at the bottom of the tub for a clog first — this is a genuinely common cause of "won't drain" symptoms and costs nothing to rule out. If the hose and screen are clear and the pump still won't run, test the pump motor with a multimeter for continuity. If there's no continuity, or the pump is getting power but still won't run, replacement is the correct fix. I already replaced the pump and it's still not draining. What should I check next? This has happened to real customers, and the cause was ultimately a clogged drain hose rather than the pump itself. If replacing the pump didn't solve the drainage problem, disconnect the drain hose and run a test cycle to see whether water is being pushed out at all — if it is, the hose downstream is the likely culprit and worth snaking out or replacing. Does this kit include the check valve flapper? This varies by supplier batch — this assembly reliably includes the pump motor, impeller, and seal, but flapper inclusion isn't consistent across all sources. Inspect your old pump's flapper for wear or damage before installation, and contact our support team if you need to confirm whether a flapper is included with your specific order. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original motor speed, impeller design, and terminal configuration of the drain pump originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10542314 Dishwasher Door Gasket and Strike Kit The XPARTCO W10542314 is an aftermarket replacement dishwasher door gasket and strike kit for select Whirlpool-built dishwashers, including Kenmore, KitchenAid, Maytag, Amana and other brands, replacing Whirlpool part W10542314. The gasket, also called the door seal or tub gasket, creates a watertight seal around the door, and the strike holds the door latch when the door is closed. When either wears out, the dishwasher may leak, the door may not latch, or it may not close properly. This kit replaces several earlier Whirlpool gasket numbers, so the new kit may be listed under a different number than your old gasket. Check your model number before ordering, as similar gaskets can differ in size and shape. Quick Answer The XPARTCO W10542314 Door Gasket and Strike Kit replaces the door gasket and latch strike on a compatible Whirlpool-built dishwasher. Replaces W10350162, W10284090, W10300589 and 8268888. Classic symptoms: water leaking from the door, the door won't close, or the latch fails. Common Problems This Part Fixes Water leaking from the dishwasher door Door won't close Door latch failure Torn, worn or gapped door gasket Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door gasket and strike kit directly replaces the following part numbers: W10542314, 2409202, 8268888, W10284090, W10300589, W10350162, W10542314VP, AP5650274, AWP40727, EAP5136129, PD00002456, PS5136129 If your old gasket shows a different number, contact our support team and we'll check whether it matches. Compatibility This kit is listed for Whirlpool, Kenmore, Kenmore Elite, KitchenAid, Maytag, Amana, Magic Chef, Crosley, Inglis, Roper and Estate dishwashers, including these examples: Whirlpool MDB6769AWW0, MDB6709AWQ2, MDB4709AWW0, RUD8000RQ0 KitchenAid KUDS01DJSB0 Kenmore 66213032K112, 66213273K112, 66513679K601 Note: The models above are a small sample. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Aftermarket replacement for the Whirlpool W10542314 gasket and strike kit Includes a door gasket and a latch strike Creates a watertight seal around the dishwasher door Helps the door latch securely when closed Replaces several earlier Whirlpool gasket numbers Product Specifications Part Number XPW10542314 OEM Part Number W10542314 Part Type Dishwasher Door Gasket and Strike Kit Condition Aftermarket Replacement Kit Includes Door Gasket, Latch Strike Application Select Whirlpool, Kenmore, KitchenAid & Maytag Dishwashers Installation Notes ⚠️ Disconnect Power Before Installing Unplug the dishwasher or shut off its circuit breaker before you begin, and wear work gloves. Remove the old gasket and clean the groove it sat in. Seat the new gasket evenly all the way around the door, without twists, and replace the latch strike. Close the door, run a cycle, and check for leaks. Frequently Asked Questions My dishwasher leaks from the door. Is this the part I need? A torn, worn or poorly seated gasket, or a failing latch strike, is a common cause of door leaks. Check the gasket for tears, gaps or cuts first. Other problems can cause the same symptoms, so confirm the gasket is the source before replacing it. What is in this kit? It includes a door gasket and a replacement latch strike. Retailers do not itemize it further. Is this an OEM or aftermarket part? This is an aftermarket replacement from XPARTCO, made to replace Whirlpool part W10542314. If you specifically need a genuine Whirlpool part, contact our support team. Will this fit my dishwasher? It is listed for many Whirlpool-built dishwashers, but the model list above is only a sample, and similar gaskets can differ in size and shape. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM W10542314 Dishwasher Door Gasket and Strike Kit The Genuine OEM Whirlpool W10542314 is a dishwasher door gasket and strike kit for select Whirlpool-built dishwashers, including Kenmore, KitchenAid, Maytag, Amana and other brands. The gasket, also called the door seal or tub gasket, creates a watertight seal around the door, and the strike holds the door latch when the door is closed. When either wears out, the dishwasher may leak, the door may not latch, or it may not close properly. This is the original Whirlpool part, not an aftermarket equivalent. It replaces several earlier Whirlpool gasket numbers, so the new kit may be listed under a different number than your old gasket. Check your model number before ordering, as similar gaskets can differ in size and shape. Quick Answer The Genuine OEM W10542314 Door Gasket and Strike Kit replaces the door gasket and latch strike on a compatible Whirlpool-built dishwasher. Replaces W10350162, W10284090, W10300589 and 8268888. Classic symptoms: water leaking from the door, the door won't close, or the latch fails. Common Problems This Part Fixes Water leaking from the dishwasher door Door won't close Door latch failure Torn, worn or gapped door gasket Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door gasket and strike kit replaces or supersedes the following part numbers: W10542314 replaces 2409202, 8268888, W10284090, W10300589, W10350162, W10542314VP, AP5650274, AWP40727, EAP5136129, PD00002456, PS5136129 If your old gasket shows a different number, contact our support team and we'll check whether it matches. Compatibility This kit is listed for Whirlpool, Kenmore, Kenmore Elite, KitchenAid, Maytag, Amana, Magic Chef, Crosley, Inglis, Roper and Estate dishwashers, including these examples: Whirlpool MDB6769AWW0, MDB6709AWQ2, MDB4709AWW0, RUD8000RQ0 KitchenAid KUDS01DJSB0 Kenmore 66213032K112, 66213273K112, 66513679K601 Note: The models above are a small sample. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool part, not an aftermarket equivalent Includes a door gasket and a latch strike Creates a watertight seal around the dishwasher door Helps the door latch securely when closed Replaces several earlier Whirlpool gasket numbers Product Specifications Part Number W10542314 OEM Part Number W10542314 Part Type Dishwasher Door Gasket and Strike Kit Condition Genuine OEM Manufacturer Whirlpool Kit Includes Door Gasket, Latch Strike Application Select Whirlpool, Kenmore, KitchenAid & Maytag Dishwashers Installation Notes ⚠️ Disconnect Power Before Installing Unplug the dishwasher or shut off its circuit breaker before you begin, and wear work gloves. Remove the old gasket and clean the groove it sat in. Seat the new gasket evenly all the way around the door, without twists, and replace the latch strike. Close the door, run a cycle, and check for leaks. Frequently Asked Questions My dishwasher leaks from the door. Is this the part I need? A torn, worn or poorly seated gasket, or a failing latch strike, is a common cause of door leaks. Check the gasket for tears, gaps or cuts first. Other problems can cause the same symptoms, so confirm the gasket is the source before replacing it. What is in this kit? It includes a door gasket and a replacement latch strike. Retailers do not itemize it further. Is this an OEM or aftermarket part? This is a genuine OEM part from Whirlpool, not an aftermarket equivalent. Will this fit my dishwasher? It is listed for many Whirlpool-built dishwashers, but the model list above is only a sample, and similar gaskets can differ in size and shape. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH23X28418 Washer Genuine GE OEM Drain Pump The WH23X28418 is a Genuine GE OEM replacement drain pump and motor assembly compatible with select GE, Hotpoint, Haier, RCA, and Kenmore top-load and front-load washers. The drain pump removes water from the washer drum during the drain and spin cycles — expelling water and detergent through the drain hose so that clothing comes out clean and free of excess water. When the pump fails, the washer will not drain, may leave standing water in the tub, or may produce loud noises during the drain cycle. This complete drain pump and motor assembly is rated at 120V, 60Hz, 1.25A with a duty cycle of 10 minutes on and 50 minutes off. It includes the pump and motor with harness — the harness and plug extend approximately 10 inches from the motor. The pump measures 5-1/4" L x 5-1/8" W x 5-1/2" H and includes a drain pump seal. It directly replaces WH23X24178 and WH23X27574, as well as several additional cross-reference numbers. Installs in 20–40 minutes with basic hand tools. Quick Answer The WH23X28418 Washer Genuine GE OEM Drain Pump fixes GE, Hotpoint, Haier, and RCA washers that won't drain, leave standing water in the tub, are noisy during draining, or leak around the pump area. Complete pump and motor with harness and drain pump seal. 120V/60Hz/1.25A. Dimensions 5-1/4" L x 5-1/8" W x 5-1/2" H; harness extends approx. 10". Replaces WH23X24178 and WH23X27574. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Washer stopping mid-cycle due to a drain fault or drain-related error code Loud humming, grinding, or buzzing noise during the drain cycle Washer pumps but will not spin — pump failure preventing cycle completion Water leaking from around the drain pump area Clothes not clean or coming out soaking wet due to incomplete drainage Pump impeller jammed by debris causing motor burnout Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: WH23X24178, WH23X28418, WH23X27574, 290D1201G001, 290D1201G002, 290D1201G003, AGE26155, B40-3A01, B30-3A02, PD00055680, EAP12723115, AP6889136, PS12723115. WH23X28418 is the current updated part number replacing the discontinued WH23X24178 and WH23X27574. If your washer documentation or old pump label shows either of those numbers, this is the correct replacement. Compatibility This drain pump is compatible with select washers from the following brands and series: GE top-load washers — GTW220, GTW330, GTW335, GTW460, GTW465, GTW485, GTW490, GTW500, GTW680, GTW720, GTW725, GTW750 series and others GE front-load washers — select GFW series models Hotpoint top-load washers — HTW200, HTW240 series and others Haier top-load washers — select models RCA top-load washers — select models Kenmore / Sears washers — select GE-built models Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Removes water and detergent from the washer drum during drain and spin cycles Complete assembly — includes pump motor, harness, and drain pump seal Rated 120V, 60Hz, 1.25A with a 10-minute on / 50-minute off duty cycle Dimensions: 5-1/4" L x 5-1/8" W x 5-1/2" H; harness and plug extend approximately 10" from motor Plastic and metal construction rated CL.A — durable and chemical resistant Includes drain pump seal to prevent leaks at the pump connection Current updated replacement for discontinued WH23X24178 and WH23X27574 — direct fit Note: The drain pump motor has been redesigned by the manufacturer — the replacement may look different from the original but fits and functions identically Genuine GE OEM part — factory-exact fit, materials, and specifications DIY-friendly repair — installs in 20–40 minutes with basic hand tools Product Specifications Part Number WH23X28418 Supersedes WH23X24178, WH23X27574 (both discontinued) Part Type Washer Drain Pump and Motor Assembly Condition Genuine OEM Application GE, Hotpoint, Haier, RCA Top-Load and Front-Load Washers Voltage 120V AC Frequency 60 Hz Amperage 1.25A Rating CL.A Duty Cycle 10 minutes ON / 50 minutes OFF Dimensions 5-1/4" L x 5-1/8" W x 5-1/2" H Harness Length Approximately 10 inches from motor Color White / Black / Gray Material Plastic / Metal Includes Pump and motor with harness, drain pump seal Compatible Brands GE, Hotpoint, Haier, RCA, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Have towels and a shallow pan ready to catch residual water. For top-load GE washers, the drain pump is typically accessed from the bottom of the machine — carefully tilt the washer back onto a support or lay it on its side to reach the pump from underneath. Disconnect the outlet hose by loosening the hose clamp and pulling it free. Disconnect the electrical harness connector. Remove the mounting screws (typically three) securing the pump to the washer base. Twist and firmly pull the old pump out. Install the new WH23X28418 pump in reverse order — connect the hose, tighten the clamp, reconnect the harness, and secure the mounting screws. Restore power and water supply and run a test cycle to verify proper drainage and no leaks. Tools needed: Phillips screwdriver, flat-head screwdriver, slip-joint pliers, shallow pan. Frequently Asked Questions What is the relationship between WH23X28418, WH23X24178, and WH23X27574? All three are GE washer drain pumps — WH23X28418 is the current updated part number that replaced both the discontinued WH23X24178 and WH23X27574. GE redesigned the pump motor during its production cycle, so the replacement may look slightly different from the original, but it fits and functions identically. If your washer uses either of the older numbers, order WH23X28418. How do I know if my washer drain pump has failed? The most common signs are standing water in the tub after a cycle, the washer stopping mid-cycle with a drain error, or loud humming during the drain phase — which indicates the motor is running but the impeller is not moving. A grinding or rattling noise suggests debris in the pump or physical damage. If the pump is completely silent during what should be the drain cycle, the motor has likely burned out and the pump needs replacement. Does the WH23X28418 fit both top-load and front-load GE washers? The WH23X28418 is primarily used in GE and Hotpoint top-load washers — the GTW and HTW series make up the majority of compatible models. It also fits select GE front-load models. Always verify your specific model number before ordering to confirm compatibility for your washer type. What is the duty cycle rating and why does it matter? The duty cycle of 10 minutes on / 50 minutes off means the pump motor is rated for up to 10 consecutive minutes of operation before requiring a 50-minute rest period. In normal washer operation this is never an issue — drain cycles are brief. However, if a drain fault causes the pump to run continuously without successfully draining, the motor can overheat. If you replace the pump due to burnout and the new pump also fails quickly, check for a drain hose blockage or control board fault that may be causing the pump to run without limit. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications — the exact same drain pump and motor assembly installed in compatible models from the factory, with guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

W11168740 - W11168743 Washer Water Valve Set for W11127357 Cold and Hot Washer Water Inlet Valve Housing and Wire Harness not included. Fits Kenmore, Maytag, Whirlpool top load washer models. Replaces Part Number:W11168740, WPW10240949, W10240949, W10921514, AP6285450, PS12348073, W11127357, W11127357, W10678672, W10678676, W10849466, W10921581, W11085642, AP6261887, PS12347475, W11168743, WPW10240948, W10240948, W10921515, AP6327638, PS12348074. Description: This Water Inlet Valve set is a replacement part for specific Kenmore, Maytag, Whirlpool washing machine models. It controls the flow of water into the washer tub at designated stages in the washing process. Water enters through the valve inlet and is distributed to internal components like the detergent dispenser, water pipes, and sump hoses. Common causes of a bad valve can include mineral scale buildup inhibiting proper flow regulation over time, or cracks and leaks from wear and tear on rubber gaskets and seals.    This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

285805 Genuine OEM Whirlpool Washer Water Inlet Valve The 285805 is a genuine Whirlpool OEM water inlet valve for direct-drive top-load washers and Whirlpool-built washer/dryer laundry centers. This valve sits at the back of the washer where the hot and cold supply hoses connect, and it controls every drop of water entering the tub — energizing to open the hot side, the cold side, or both together when the control calls for a fill, and closing again once the correct level is reached. It's one of the longest-running, most widely used inlet valves on the Whirlpool direct-drive platform, the same platform that our 8318084 lid switch listing also serves. This is a complete kit: it ships with the mounting bracket, screws, and installation instructions, and it accepts a 1/2" ID hose through two 3/4"-11 threaded NHT ports. Depending on production run, the valve body may arrive blue or green — both are correct and function identically. Over years of use, mineral and sediment buildup (especially calcium deposits from hard water) can restrict or block the valve, the internal solenoid coil can burn out electrically, and the rubber seals can simply wear out with age. A blocked or failing valve commonly shows up as slow filling, no fill on one side, continuous filling that won't stop, or leaking after the cycle ends. It directly replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, and W10110517. Quick Answer The 285805 Genuine OEM Whirlpool Washer Water Inlet Valve fixes direct-drive top-load washers and Whirlpool-built washer/dryer laundry centers that won't fill, fill slowly, won't stop filling, leak after the cycle, or have no hot or no cold water. Complete kit with mounting bracket, screws, and instructions. Dual-port valve for a 1/2" ID hose, two 3/4"-11 NHT threaded connections, approximately 5.7" tall. Replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, W10110517. The included bracket may be shaped differently than your original integrated bracket — you may need to test a couple of orientations to get the hose connections positioned correctly. Common Problems This Part Fixes Washer won't fill with water at the start of the cycle Washer fills much more slowly than normal Washer won't stop filling — overfilling past the normal level Water leaking or dripping from the washer after the cycle has ended No hot water reaching the tub, or no cold water reaching the tub Washer not washing properly due to insufficient or incorrect-temperature water Cycle stalling at the fill step and never advancing to wash Hot water inlet blocked by calcium or mineral deposits after years of hard-water use Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: 285805, 285805VP, AP3094541, 21026, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, W10110517, AH334646, EA334646, AWP39626, PD00002373, PS334646. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select direct-drive top-load washers and washer/dryer laundry centers across the Whirlpool family of brands, including: Whirlpool top-load washers and laundry centers Maytag top-load washers (select Whirlpool-built models) KitchenAid, Jenn-Air, and Amana top-load washers (select models) Roper, Admiral, Hardwick, and Estate top-load washers (select models) Magic Chef, Crosley, Inglis, Norge, Modern Maid, and Caloric top-load washers (select models) Select Kenmore and Ikea top-load washers built on the Whirlpool platform Note: This valve fits Whirlpool's direct-drive top-load platform, including stackable washer/dryer laundry centers — the same general platform used by our 8318084 lid switch listing. It is not intended for front-load washers, which use a different valve design. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid, seal, and flow-rate design Complete kit — includes mounting bracket, screws, and installation instructions Dual-port design accepts a 1/2" ID hose through two 3/4"-11 NHT threaded connections Resolves "won't fill," "fills slowly," "won't stop filling," and "leaking after cycle" symptoms caused by valve failure One of the most widely used inlet valves on the Whirlpool direct-drive top-load platform Approximately 5.7" tall, metal and plastic construction Replaces AP3094541, 21026, 285805VP, 292197, 3349451, 3354565, 3360387, 3360388, 3360389, 3360391, 3360392, 3429537, 358992, 370067, 388328, 3952163, 3952164, 3955673, 8228, 868761, 99989697, AH334646, EA334646, PS334646, and W10110517 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, and related direct-drive top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 285805 Part Type Washer Water Inlet Valve Kit Condition Genuine OEM Brand Whirlpool Application Direct-Drive Top-Load Washers / Laundry Centers Kit Contents Water inlet valve, mounting bracket, screws, instructions Ports 2 (hot and cold) Hose Compatibility 1/2" ID Thread Specification Two 3/4"-11 x 1/2" NHT hose threads Height Approx. 5.7 in. Material Metal and plastic Color Blue or green (both correct — varies by production run) Quantity 1 valve kit Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, Hardwick, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Caloric, Kenmore, Ikea Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Bracket Orientation May Take Trial And Error Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Pull the washer away from the wall for access, then disconnect the hot and cold water supply hoses from the back of the valve — have a towel ready, since residual water will spill out. Remove the screws securing the rear or top cabinet panel (on some stackable laundry centers, the entire top enclosure lifts off as one piece, which also disconnects the lid switch wiring harness at the rear — note this connector's location before pulling the panel free). Photograph the wiring and hose routing before disconnecting anything. Unplug the wiring harness from the old valve, remove its mounting screws, and pull it free along with its bracket. Some original valves used an integrated bracket, while this replacement kit ships with a separate bracket that has multiple mounting holes to fit different configurations — you may need to test a couple of orientations before the hose connections line up correctly with your existing hoses. Mount the new 285805 to the bracket, secure it in the cabinet in the same general position as the old valve, and reconnect the wiring harness. Reattach the hot and cold supply hoses to the correct ports, tightening securely by hand plus a partial turn with pliers. Reinstall the cabinet panel, reconnecting the lid switch harness if applicable, restore the water supply, and check every connection for leaks before restoring power. Run a short cycle and confirm the tub fills at the normal rate with no leaking. Tools needed: Phillips screwdriver, pliers, towel, work gloves. Frequently Asked Questions My valve is blue but the old one was green (or vice versa). Did I get the wrong part? No — this is normal. The 285805 has shipped with either a blue or a green valve body depending on the production run, and both are the correct, fully functional part. The color has no effect on fit or performance. The new valve's bracket doesn't match my old one. What do I do? This is a known and expected difference. Many original valves used a bracket integrated directly into the valve body, while this replacement kit ships with a separate bracket that has multiple mounting holes to accommodate different washer configurations. It may take a little trial and error to find the orientation that positions the valve correctly for your existing hose connections — this is a bracket design difference, not a sign that the wrong part was sent. Only hot water won't fill, but cold works fine. Is that this valve? Yes, likely — and often it's specifically mineral or calcium buildup rather than outright failure. Hot water tends to accelerate scale buildup inside the valve port compared to cold, so after many years of hard water use, the hot side can become restricted or fully blocked while the cold side continues working normally. Replacing the valve resolves this since the internal ports aren't designed to be cleaned out once heavily scaled. My washer won't stop filling. Is that dangerous, and is it this valve? It can lead to overflow and water damage if left unaddressed, so it's worth shutting off the water supply at the wall if this happens rather than waiting. A valve that won't stop filling usually means a worn internal seal or diaphragm is no longer sealing shut when the solenoid de-energizes, letting water continue flowing. This valve is the correct replacement for that symptom. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same dual-port solenoid design, thread specifications, and flow-rate calibration as the water inlet valve originally installed in your direct-drive top-load washer or laundry center. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11688994 Washer Genuine OEM Water Valve Single water inlet valve, hot Replaces Part Numbers: W11688994, W11316255, W11036928, W11486360, AP7218602, PS17216729. Description: This Water Inlet Valve is a Genuine OEM part for specific Maytag, Kenmore, Whirlpool washing machine models. It controls the flow of water into the washer tub at designated stages in the washing process. Water enters through the valve inlet and is distributed to internal components like the detergent dispenser, water pipes, and sump hoses. Common causes of a bad valve can include mineral scale buildup inhibiting proper flow regulation over time, or cracks and leaks from wear and tear on rubber gaskets and seals. 

Read more less

XPARTCO 5221ER1003S Washer Water Valve The XPARTCO 5221ER1003S is an aftermarket replacement cold water inlet valve for LG and select Kenmore front-load washers. This valve sits underneath the top panel, at the point where the cold water supply hose connects, and it's the gatekeeper for cold water entering the tub. When the control calls for a cold fill, it energizes the valve's solenoid to open, admitting water; once the correct level is reached, it closes again. This part controls the cold water side specifically — hot fills on these washers are governed by a separate valve. Rated 12V and terminated with small male spade connectors, this valve measures approximately 4.75"H x 3.25"W x 2.25"L, with a gray plastic and metal housing. Over time, rust and mineral buildup inside the valve body — a documented failure point on this platform — can prevent it from sealing fully, which lets water continue flowing even after the valve is told to close. A washer that keeps filling even while draining, or that leaks steadily at the cold connection, is a strong sign of exactly this kind of stuck-open valve failure. Other failure modes include a burned-out solenoid coil and general wear from age. It directly replaces 4869496, AP6798394, PS12587936, and EAP12587936, and is also cross-referenced to the related 5221ER1003A part number. Quick Answer The XPARTCO 5221ER1003S Washer Water Valve fixes LG and select Kenmore front-load washers where cold water won't fill, fills slowly, keeps filling continuously (even while draining), or leaks at the water connection. 12V cold water inlet valve, small male spade terminals, 4.75"H x 3.25"W x 2.25"L. Replaces 4869496, AP6798394, PS12587936, EAP12587936. Rust and mineral buildup inside the valve body is a documented cause of it sticking open — check for rust at the connection before you order. Common Problems This Part Fixes Washer won't fill with cold water at the start of the cycle Cold water fills much more slowly than it used to Washer keeps filling continuously, even while water is simultaneously draining out Water leaking steadily at the cold water connection point Visible rust or mineral buildup around the valve body or connection Cycle stalling at the fill step and never advancing to wash Water pooling underneath or behind the washer near the cold supply line Cold wash or cold rinse cycles specifically affected while other cycles run fine Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer cold water inlet valve directly replaces the following OEM and cross-reference part numbers: 5221ER1003S, 5221ER1003A, 4869496, AP6798394, PS12587936, ALG51905, PD00057211, EAP12587936 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cold water inlet valve is compatible with select LG front-load washers, and also fits select Kenmore front-load washers built on the LG platform, including model numbers such as: LG WM4000HBA, WM4000HWA, WM3400CW, WM3470CW LG W3600HVA Kenmore WKE100HVA (select LG-built models) Note — cold side only: This is the cold water valve. Some LG front-load washers use a separate hot water valve for the hot supply connection — if hot water fills normally but cold does not, this valve is the correct part; if the issue affects both hot and cold fills, the problem may lie elsewhere in the fill circuit. This valve is specific to LG's front-load platform and is not intended for top-load washers. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement cold water inlet valve for LG and select Kenmore front-load washers Resolves "won't fill with cold water," "fills slowly," "keeps filling continuously," and "leaking at the connection" symptoms caused by valve failure Rated 12V with small male spade terminal connections for a secure electrical fit Gray plastic and metal housing, approximately 4.75"H x 3.25"W x 2.25"L Direct drop-in replacement — mounts underneath the top panel at the original connection point Replaces 4869496, AP6798394, PS12587936, and EAP12587936 Compatible with LG and select Kenmore front-load washers Aftermarket replacement built to OEM-equivalent quality standards Straightforward DIY repair using basic hand tools Product Specifications Part Number 5221ER1003S OEM Part Number 5221ER1003S (also 5221ER1003A) Part Type Washer Water Inlet Valve — Cold Condition Aftermarket Replacement Brand LG Application Front-Load Washers Voltage 12V Electrical Connection Small male spade terminals Color Gray Material Plastic and metal Height 4.75 in. Width 3.25 in. Length 2.25 in. Location Underneath the top panel, dispenser and control panel assembly Quantity 1 valve Compatible Brands LG, select Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Have A Towel Ready Unplug the washer and shut off the cold water supply valve before beginning. Wear work gloves. Pull the washer away from the wall for access. Unthread the cold water supply line from the back of the valve first — have a towel ready, since residual water will spill out. Unthread the two screws securing the top panel, then slide the panel back and lift it off to access the valve assembly underneath. Photograph the wiring connections before disconnecting anything. Disconnect the spade terminal wire connectors from the old valve, remove its mounting screw or bracket, and pull the valve free. While it's out, inspect the area for rust or mineral scale, and clean the connection point if needed before installing the new valve. Install the new 5221ER1003S in the same position, reconnect the spade terminals, and secure the mounting hardware. Rethread the cold water supply line onto the new valve, tightening securely. Reinstall the top panel and its two screws. Restore the water supply and power, then run a short cycle and confirm the tub fills at the normal rate with no leaking underneath or behind the washer. Tools needed: channellock pliers, flathead screwdriver, pliers, drill/driver with a Phillips bit, towel, work gloves. Frequently Asked Questions My washer keeps filling even while it's draining. Is that this valve? Yes, this is a well-documented failure mode on this platform. Rust and mineral buildup inside the valve body can prevent it from sealing fully closed, so water keeps trickling or flowing into the tub even after the fill portion of the cycle has ended — sometimes enough to keep pace with draining, making it look like the washer is filling and draining simultaneously. If you open up the top panel and see rust around the valve, that strongly confirms this diagnosis. Cold water won't fill but hot water works fine. Is this the right part? Yes — this valve controls cold water specifically, and some LG front-load washers use a separate valve for the hot supply. If cold-specific cycles are failing while hot water fills normally, this cold valve is the correct part to replace. I see rust on my old valve but it isn't leaking yet. Should I still replace it? It's worth strongly considering. Rust and mineral buildup on this valve is a known precursor to it sticking partially open, which can lead to continuous filling, water waste, and potential water damage if it isn't caught. If you're already inspecting the area and see corrosion forming, replacing the valve proactively is often cheaper and easier than dealing with an active leak later. What's the difference between 5221ER1003S and 5221ER1003A? These are cross-referenced as the same valve — 5221ER1003A appears on some parts diagrams and listings as an alternate or prior designation for the identical part. If your washer's diagram shows either number, this listing is the correct replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the 12V solenoid design, spade terminal connections, and dimensions of the original 5221ER1003S cold water valve used in compatible LG and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO AJU75152602 Washer Water Inlet Valve The XPARTCO AJU75152602 is an aftermarket replacement washer water inlet valve assembly compatible with select LG and Kenmore top-load washers in the larger-capacity WT7 series — including the WT7060, WT7100, WT7150, WT7155, WT7250, WT7300, WT7305, WT7400, WT7405, WT7800, WT7880, and WT7900 series. The water inlet valve is a multi-port solenoid valve mounted on the back of the washer that controls the flow of hot and cold water into the tub and dispenser compartments during fill and rinse cycles. When any valve port fails, the washer may not fill at all, fill too slowly, fill with the wrong water temperature, overfill, or leak from the valve body. This valve assembly directly replaces 5221EA1008S, 4873914, AP6335382, EAP12580369, PS12580369, and PD00060681. It includes two integrated inlet screens to filter debris from the supply lines. Installs in 15–25 minutes with basic hand tools. Note: the AJU75152602 is for the WT7xxx larger-capacity LG top-load series — it is not the same valve as the AJU75152601, which is used on the earlier and smaller-capacity WT1xxx through WT5xxx series. Verify your model number before ordering. Quick Answer The XPARTCO AJU75152602 Washer Water Inlet Valve fixes LG WT7xxx-series top-load washers that won't fill, fill slowly, fill with wrong temperature, overfill, or leak from the valve. Includes 2 inlet screens. Replaces 5221EA1008S, 4873914, AP6335382, EAP12580369, PS12580369, PD00060681. Compatible with LG WT7060, WT7100, WT7150, WT7300, WT7305, WT7400, WT7405, WT7800, WT7880, WT7900 series and Kenmore (LG-built). Note: not the same as AJU75152601 — different model series. Common Problems This Part Fixes Washer not filling with water at all when a cycle is started Washer filling very slowly — taking much longer than normal to reach water level Washer filling with only cold water on a warm or hot cycle — hot solenoid failed Washer filling with only hot water on a cold cycle — cold solenoid failed Washer overfilling or filling continuously — valve port stuck open Water temperature incorrect despite correct cycle selection Water dripping into the tub between cycles — valve not sealing completely Water leaking from the back of the washer near the valve body Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: AJU75152602, 4873914, 5221EA1008S, U8EONG(9F), IV-248-103, PD00060681, FIX12580369, ALG53788, AP6335382, PS12580369, DC12V 6W, IV-248-103, U8EONG(9F). If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select LG WT7 series top-load washers and related Kenmore models: LG WT7060CV, WT7060CW LG WT7100CW LG WT7150CW, WT7155CW LG WT7250CW LG WT7300CV, WT7300CW LG WT7305CV, WT7305CW LG WT7400CV, WT7400CW LG WT7405CV, WT7405CW LG WT7800CV, WT7800CW LG WT7880HWA LG WT7900HBA Kenmore 31452 and select LG-built Kenmore models Important — AJU75152602 vs AJU75152601: These are two different valves for different LG washer generations. The AJU75152602 is for the larger-capacity WT7xxx series. The AJU75152601 is for the earlier and smaller-capacity WT1xxx through WT5xxx series. They are not interchangeable. Always verify your model number before ordering. Key Features Multi-port solenoid valve — controls hot water, cold water, and dispenser ports to deliver the correct water temperature and volume for each cycle phase Includes two integrated inlet screens — filter debris and mineral deposits from the supply lines before they reach the valve seat ABS plastic and stainless steel construction — durable and resistant to mineral buildup and corrosion Replaces 5221EA1008S, 4873914, AP6335382, EAP12580369, PS12580369, and PD00060681 Compatible with LG WT7060, WT7100, WT7150, WT7300, WT7305, WT7400, WT7405, WT7800, WT7880, WT7900 series and Kenmore LG-built models For WT7xxx series only — not the same as AJU75152601 (WT1xxx–WT5xxx series) Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–25 minutes with basic hand tools Product Specifications Part Number AJU75152602 Part Type Washer Water Inlet Valve Assembly (Multi-Port) Condition Aftermarket Replacement Application LG WT7xxx Series Top-Load Washers Material ABS plastic / Stainless steel Kit Includes Valve assembly + 2 integrated inlet screens Note WT7xxx series only — not interchangeable with AJU75152601 (WT1xxx–WT5xxx) Compatible Brands LG, Kenmore (LG-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off both the hot and cold water supply valves before beginning. Pull the washer away from the wall to access the back panel. The water inlet valve is mounted on the upper rear of the washer. Photograph all wire harness connections and hose positions before disconnecting. Disconnect the two external supply hoses from the valve inlet ports. Disconnect the internal outlet hoses by squeezing the retaining clips and pulling free. Disconnect the wiring harness connectors from each solenoid port. Unscrew the mounting screws and remove the old valve. Install the new AJU75152602 valve in the same position, reconnect all internal hoses, wire harnesses, and external supply hoses in the documented positions. Restore water supply and power, then run a fill cycle to verify normal filling and check for leaks. Tools needed: Phillips screwdriver, pliers. Frequently Asked Questions What is the difference between AJU75152602 and AJU75152601? These are two different water inlet valve assemblies for different generations of LG top-load washers. The AJU75152601 (which also replaces AJU73213301 and 5221EA1008F) is used on LG's earlier and smaller-capacity top-load washers in the WT1xxx, WT4xxx, and WT5xxx series. The AJU75152602 (which replaces 5221EA1008S) is for LG's larger-capacity WT7xxx series. Despite appearing similar, they have different port configurations and are not interchangeable. Always verify your specific model number before ordering. How do I know if the water inlet valve has failed? Common signs are the washer not filling, filling only on one temperature setting, overfilling, dripping between cycles, or leaking from the valve area. Before replacing the valve, check that both supply valves are fully open and the hoses are not kinked. You can test each solenoid coil with a multimeter — a working coil shows resistance (typically 200–500 ohms); an open circuit confirms that coil has failed. Also inspect and clean the inlet screens inside the supply port openings — mineral-clogged screens can restrict flow enough to cause the same symptoms as a failed valve. What are the two inlet screens included with the valve? The two mesh screens that come with the AJU75152602 install inside the hot and cold water inlet ports of the valve. They catch sediment, mineral particles, and debris from the household water supply before they can reach the solenoid valve seats. Installing fresh screens along with the new valve helps extend the valve's service life, especially in areas with hard water. If the previous valve failed due to mineral buildup rather than an electrical fault, cleaning the supply hoses before installation is also recommended. My LG WT7300CW is only filling with cold water — is this the valve? Filling with only cold water on a warm or hot cycle is a classic sign that the hot water solenoid coil on the inlet valve has failed. Each temperature port is controlled by its own independent solenoid — when the hot solenoid fails, only the cold port opens. Before replacing the valve, also confirm that the household hot water supply valve is fully open and that hot water is reaching the back of the washer in the supply hose. If hot water supply is confirmed and the cold-only fill persists, replace the AJU75152602 valve. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from ABS plastic and stainless steel to match the port configuration and specifications of the original AJU75152602 water inlet valve assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 137221600 Washer Drain Pump The XPARTCO 137221600 is an aftermarket replacement washer drain pump compatible with a wide range of Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse front-load washers — including popular Affinity series and washer-dryer combo models. The drain pump is mounted at the base of the washer and is responsible for evacuating the wash and rinse water from the tub through the drain hose at the end of each cycle. When the drain pump fails, the washer can't drain — leaving clothes soaking wet, water pooling in the tub, and the wash cycle unable to advance to spin. Common failure symptoms include humming without pumping (blocked or seized impeller), leaks from the pump housing, loud grinding or clicking noises, and complete pump silence when a drain cycle should be running. Rated 120V AC, 60Hz, 85W, 1.25A. Based on the Askol M65 design, with a firmly attached red flapper to prevent drain backflow into the tub. Constructed from strong, durable plastic to resist cracking and leaking through many years of cycling. Package includes the drain pump, mounting base, and mounting screw. This part directly replaces 137108100, 137151800, 137151800KITK, 131724000, 134051200, 134740500, 134740800, 2754548, ER137108100, TJ137108100, EAP7783938, LP1600, BPX401-72J, AP5684706, and PS7783938. Important: before installing the new pump, clean any lint or debris from the rubber boot, verify the drain hose is clear and properly fastened, and check the pump filter for blockage — installing a new pump on a system with the underlying blockage will not resolve the drainage problem. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO 137221600 Washer Drain Pump fixes Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse front-load washers that won't drain, leave clothes soaking wet, are noisy or humming during the drain cycle, or display an E11 error code. 120V AC, 60Hz, 85W, 1.25A. Askol M65 design with red backflow flapper. Kit includes pump + mounting base + screw. Replaces 137108100, 137151800, 137151800KITK, 131724000, 134051200, 134740500, 134740800, 2754548, ER137108100, TJ137108100, EAP7783938, LP1600, BPX401-72J, AP5684706, PS7783938. Common Problems This Part Fixes Washer not draining — pump failed to remove water at the end of the wash or rinse cycle Clothes left soaking wet at the end of the cycle — no drain, so no spin can start Water leaking from the bottom of the washer — cracked pump housing or failed seal Loud humming noise but no water flowing — pump motor running against a seized impeller or blockage Grinding, clicking, or unusual noises during the drain cycle E11 error code displayed on the control panel (drain fault) Washer pumps but won't spin — drain cycle can't complete, blocking spin Cycles taking much longer than normal as the washer tries to drain Pump silent during drain — motor windings open or electrical fault Impeller broken, cracked, or missing pieces after opening the pump Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: 137221600, 131724000, 134051200, 134740500, 137108100, 137151800, 137151800KITK, 2754548, TJ137108100, ER137108100, PD00000118, EAP7783938, BPX401-72J, AFR14249, AP5684706, PS7783938, Also replaces GE WH23X10041, 2119312, WH23X10009, WH23X10017, WH23X10031, WH23X10034, AH3502779, EA3502779, AP5324214, PS3502779. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump is compatible with select front-load washers and washer-dryer combos from the following brands: Frigidaire front-load washers — Affinity series (FAFW3001LW3, FAFW3801LW3 and related), FEX831FS2/FS4, FTF2140ES1, FWS445RFS2, FWX445RFS3 series Frigidaire front-load washers — ATF6000ES1, ATF8000FS1, ATFB6700FS0 series Frigidaire front-load washers — GLTF2940ES3, GLTF2940FS1 and related GLTF series Frigidaire washer-dryer combos — CWS3600AS1 and related Electrolux front-load washers — select models Crosley front-load washers — select models Gibson front-load washers — select models Kelvinator front-load washers — select models Kenmore / Sears front-load washers — select Frigidaire-built models (41744052400, 41744052401, 41744052500, 41744082500, 41748102700, 41748106700, 41748116700, 41790812995 and related 417-series) Tappan front-load washers — select models Westinghouse front-load washers — select models Note: The redesigned 137221600 may look slightly different from your original (e.g., white or gray housing vs. original black), but functions identically. Ensure proper orientation and flapper alignment during installation. Always verify your appliance model number before ordering. Key Features Aftermarket replacement built to OEM-equivalent quality standards Drain pump — removes water from the washer tub through the drain hose at the end of the wash and rinse cycles Resolves "won't drain," "won't spin," "wet clothes," "E11 error," and "humming pump" symptoms 120V AC, 60Hz, 85W, 1.25A — correct electrical specifications for compatible Frigidaire-platform washers Askol M65 design with red backflow flapper to prevent water from flowing back into the tub Strong, durable plastic construction resistant to cracking and leaking Kit includes: 1x drain pump, 1x mounting base, 1x mounting screw Replaces 15+ OEM and cross-reference part numbers including 137108100, 137151800, 131724000, 134051200, 134740500, 134740800, AP5684706, and PS7783938 Compatible with Frigidaire (Affinity, FEX, FTF, FWS, FWX, ATF, ATFB, GLTF, CWS series), Electrolux, Crosley, Gibson, Kelvinator, Kenmore (417-series), Tappan, and Westinghouse front-load washers and washer-dryer combos DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number XP137221600 Part Type Washer Drain Pump Condition Aftermarket Replacement Application Front-Load Washers and Washer-Dryer Combos (Frigidaire/Electrolux platform) Voltage 120V AC Frequency 60 Hz Wattage 85W Amperage 1.25A Design Askol M65 with red backflow flapper Material Durable plastic Includes 1x Drain Pump, 1x Mounting Base, 1x Mounting Screw Error Codes Resolved E11 (drain fault) Compatible Brands Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, Westinghouse Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Work Gloves — Check for Blockage First Disconnect power at the outlet or breaker and shut off both water supplies at the wall before beginning. Wear work gloves to protect your hands — pump components can have sharp edges. Have towels ready — residual water remains in the pump housing and hoses. Important: before replacing the pump, check for the underlying cause of the drain problem. Inspect the pump filter (accessible on many models via the lower front kick panel), the drain hose for kinks, and the rubber boot at the bottom of the tub for lint, coins, buttons, or other debris — installing a new pump on a system with an unresolved blockage will not fix the drain problem. Remove the appropriate access panel (typically the rear or front lower kick panel — model-dependent) to expose the pump. Photograph the wire harness and hose connections before disconnecting. Disconnect the electrical wire connectors from the pump motor. Squeeze the hose clamps with pliers and slide them back to release the tub-to-pump hose and the pump-to-drain-hose from the pump. Remove the 2 mounting screws holding the pump to its base and lift the old pump out. Clean any residual debris from the rubber boot, hoses, and pump filter area. Install the new 137221600 pump using the included mounting base and screw. Reconnect the hoses with the clamps, orient the red backflow flapper correctly, and reconnect the electrical connectors. Reinstall the access panel, restore water and power, and run a rinse cycle to test drainage and check for leaks at all connections. Tools needed: Phillips screwdriver, needle-nose pliers, channel-lock pliers, small flathead screwdriver, towel, work gloves. Frequently Asked Questions My washer won't drain — is it always the pump? Not always. Before replacing the pump, check for these common causes: 1) Clogged pump filter — most Frigidaire front-load washers have a filter accessible via the lower front kick panel; coins, buttons, lint, and small items can block it. 2) Kinked or clogged drain hose — inspect the entire drain hose from the pump to the wall standpipe or sink. 3) Blocked rubber boot — small items can get stuck between the tub and the pump inlet. 4) Failed lid lock/door switch — if the washer doesn't detect a locked door, it won't run the drain cycle. If all of these check out and the pump still isn't draining (or is humming without moving water), the pump has failed and this is the correct repair. What is the E11 error code on my Frigidaire washer? E11 on Frigidaire and Electrolux front-load washers indicates a drain fault — the control board is not detecting successful drainage within the expected time. Common causes are a failed drain pump, a clogged pump filter, a kinked or clogged drain hose, or debris blocking the impeller. If you've verified the filter and hose are clear but the code persists, replacing the 137221600 drain pump typically resolves it. If the code returns after replacement, check the wire harness between the pump and the control board. Does the pump come with everything I need for installation? Yes — the 137221600 (OE) package includes the drain pump itself, a mounting base, and a mounting screw. This is everything you need for the pump replacement itself. However, you should reuse the original hose clamps and hoses from your old pump (they should still be in good condition). If you find that the rubber boot at the base of the tub is cracked, hardened, or torn during the repair, that's a separate part that would need to be ordered — inspect it before completing the reinstallation. The new pump looks different from my old one — is it the right part? Very likely, yes. The 137221600 has been through several revisions over its production history — some housings are black, others white or gray, and the exact shape can vary slightly across production runs. As long as the mounting bolt pattern, hose inlet/outlet sizes, and electrical connector are the same, and the specs match (120V, 60Hz, 85W, Askol M65 design), the pump will function identically to your original. During installation, focus on correct orientation and flapper alignment — the flapper (red) must be positioned so it opens outward toward the drain hose direction to prevent backflow. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured to match the electrical specifications (120V AC, 60Hz, 85W, 1.25A), Askol M65 design, red backflow flapper, dimensions, and drain pump function of the original 137221600 used in compatible Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH13X26535 Genuine OEM GE Washer Water Valve The WH13X26535 is a genuine GE OEM water inlet valve assembly for GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café models. This valve controls the flow of hot and cold water into the tub during the fill portion of the cycle, ensuring each wash uses the correct amount of water at the right temperature blend. It's housed in durable gray plastic. Common failure causes include mineral or sediment buildup inside the valve body, a burned-out internal solenoid coil, and general wear over years of use — five years is a commonly cited service life before this valve starts to show problems. A failing valve produces a clear set of symptoms: the washer not filling properly, water continuing to fill or drip even when the washer is turned off, or leaking near the valve area. It directly replaces AP6892695, WH13X24386, 4931303, PS12726769, WH13X24392, WH13X26535-25PK, EAP12726769, and PD00052736. As a genuine OEM part, the WH13X26535 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance. Quick Answer The WH13X26535 Genuine OEM GE Washer Water Valve fixes GE top-load washers that aren't filling properly, are overfilling, or have water slowly dripping into the tub even when the washer is off. Housed in gray plastic. Replaces AP6892695, WH13X24386, 4931303, PS12726769, WH13X24392, WH13X26535-25PK, EAP12726769, PD00052736. This replacement valve does not include a thermistor or gasket — if your old valve has a thermistor mounted in front of the solenoids, you'll need to transfer it (with its gasket) to the new valve. Also not the same as the similarly-numbered WH13X26534, which is a separate valve for other GE/Hotpoint models. Common Problems This Part Fixes Washer not filling with water properly Washer overfilling Water slowly dripping or leaking into the tub even when the washer is turned off Leaking near the valve connections No hot water reaching the tub, or no cold water reaching the tub Cycle stalling at the fill step and never advancing to wash Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: WH13X26535, WH13X24386, WH13X24392, 4931303, 003C17, AGE26261, AP6892695, 4476388, 4931303, OEM20678094, EAP11729481, EAP12726769, K-78637-2, PD00052736, PS12726769. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café washers built on the GE platform, spanning model series GTW460, GTW465, GTW485, GTW490, GTW500, GTW525, GTW540, and VTW540, including specific model numbers such as 5TW4207ST0WS, 5TW4307SW0WS, ETW485ASW0WB, GTW460AMJ0WW, GTW460AMJ1WW, and GTW460AMJ2WW. Note — thermistor transfer required, and not the same as WH13X26534: This valve does not include a thermistor or the rubber gasket that seats it. If your original valve has a thermistor mounted in front of the solenoids, you must transfer that thermistor and its gasket onto this new valve during installation. Separately, this part is not the same as the similarly-numbered WH13X26534, a distinct valve used on other GE/Hotpoint models with its own cross-reference set (PS12726768, AP6891106). Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified solenoid design and housing Controls hot and cold water flow into the tub Resolves "won't fill properly," "overfilling," and "dripping into the tub when off" symptoms caused by valve failure Durable gray plastic housing Direct drop-in replacement — matches the original mounting and hose connections Replaces AP6892695, WH13X24386, 4931303, PS12726769, WH13X24392, WH13X26535-25PK, EAP12726769, and PD00052736 Compatible with GE, Hotpoint, Haier, Monogram, and Café top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Moderate DIY repair, typically 30 to 60 minutes Product Specifications Part Number WH13X26535 Part Type Washer Water Inlet Valve Condition Genuine OEM Application Top-Load Washers Housing Material Gray plastic Includes Thermistor/Gasket No — transfer from old valve if equipped Repair Difficulty Moderate — 30 to 60 minutes Quantity 1 valve Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Watch For The Thermistor O-Ring Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Access is typically behind the front control panel or top of the cabinet, depending on your model. The valve assembly is usually held in place with a metal plate and two screws. Photograph the wiring and hose connections before disconnecting anything. If your old valve has a thermistor (temperature sensor) mounted in front of the solenoids, it fits into a small hole in the bracket and uses an O-ring seal that's known to degrade and leak over time — this new valve does not include one, so you'll need to carefully transfer the thermistor and its gasket from the old valve to the new one. Disconnect the electrical connector and outlet hoses from the old valve, remove its mounting screws, and pull it free. Transfer the thermistor and gasket to the new WH13X26535 if applicable, then install it in the same position, reconnect all outlet hoses to their original positions, reconnect the electrical connector, and secure the mounting screws. Reattach the hot and cold supply hoses, tightening securely. Restore the water supply and check every connection for leaks before restoring power. Run a full test cycle across a few different temperature settings to confirm each fill function works correctly with no leaking. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions Does this valve come with the thermistor? No. This valve no longer comes with the rubber gasket or thermistor that some GE washers use, mounted directly in front of the solenoids. If your old unit has one, you'll need to remove it from the old valve, along with its gasket, and transfer it onto this new valve during installation. Water has been slowly leaking into my tub even when the washer is off. Is that this valve? Yes, this is a documented cause. One customer traced over a year of slow leaking directly to this valve's thermistor O-ring, which is known to degrade over time and let water seep through even when the washer isn't running. Replacing the valve (and transferring a good thermistor and gasket if your model uses one) resolves this type of slow leak. Is this the same as WH13X26534? No, these are two separate GE valve part numbers with different cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close number match. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, housing, and connection type of the water inlet valve originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less