Search results for "dryer idler pulleys"

W11612327 Dishwasher Genuine Circulation Pump Circulation pump and motor assembly Replaces Part Numbers: W11612327, W11024423, W10805387, W11521436, AP7194668, PS16744935. Description: This Pump is a Genuine component for specific Whirlpool dishwasher models. It refers to the water pump component that circulates water throughout the dishwasher during cycles. Common cause of a faulty pump can include normal wear over many uses. The continuous motor operation puts strain on internal seals and impellers. Mineral deposits from hard water can also clog pump parts over time.

Read more less

XPARTCO DC97-19289F Washer Drain Pump Assembly The XPARTCO DC97-19289F is an aftermarket replacement washer drain pump assembly compatible with a wide range of Samsung top-load washers in the WA40, WA41, WA42, WA44, WA45, WA48, WA50, WA52, and WA54 series, as well as select Kenmore models built on the Samsung platform. The drain pump removes water from the washer tub during the drain portion of each wash cycle. When the pump fails, the washer will display error codes 5C, SE, nd, 5E, FO2, or E5, leave standing water in the tub, stop mid-cycle, or produce unusual noise during draining. This complete drain pump assembly is rated 120V, 60Hz, 80W, 1.1A with a 30-minute on / 30-minute off duty cycle. It directly replaces DC97-19289A, DC97-19289B, DC97-17349B, DC97-17366A, DC97-17366J, and PX3516-01. Note: the wire plug on the new pump may differ slightly from the original — if the connector does not match your washer's harness, transfer the wiring harness from the old pump to the new one. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DC97-19289F Washer Drain Pump Assembly fixes Samsung top-load washers displaying error codes 5C, SE, nd, 5E, FO2, or E5, not draining, leaving standing water, or making loud noise during the drain cycle. 120V/60Hz/80W/1.1A, 30 min on/30 min off duty cycle. Compatible with Samsung WA40 through WA54 series and Kenmore (Samsung-built). Replaces DC97-19289A, DC97-19289B, DC97-17349B, DC97-17366A, DC97-17366J, PX3516-01. Note: if wire plug differs, transfer harness from old pump. Common Problems This Part Fixes Error codes 5C, SE, nd, 5E, FO2, or E5 — washer cannot drain within the allotted time Washer not draining — standing water remaining in the tub after a cycle Washer stopping mid-cycle due to a drain fault Loud humming, grinding, or rattling noise during the drain cycle Water draining very slowly — worn pump motor below rated performance Water leaking from the drain pump area at the bottom of the washer Pump running continuously but water not being expelled from the tub Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: DC97-19289F, DC97-17349B, DC97-19289B,DC97-17366A, DC97-17366J, DC97-19289A,ASM772133, AP6806651, EAP12592631, PD00049911, PX3516-01, PS12592631. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump is compatible with select top-load washers from the following brands and series: Samsung top-load washers — WA40 series (WA400PJHDWR and related models) Samsung top-load washers — WA41 series (WA41A3000AW and related models) Samsung top-load washers — WA42 series Samsung top-load washers — WA44 series (WA44A3205AW and related models) Samsung top-load washers — WA45 series (WA45H7000AW, WA45M7050AW, WA45N3050AW, WA45T3200AW and related models) Samsung top-load washers — WA48 series (WA48H7400AW and related models) Samsung top-load washers — WA50 series (WA50F9A7DSP, WA50M7450AW and related models) Samsung top-load washers — WA52 series (WA52M7750AW, WA52M8650AW and related models) Samsung top-load washers — WA54 series (WA54M8750AV and related models) Samsung top-load washers — WA456DRHDSU series Kenmore / Sears top-load washers (select Samsung-built models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Removes water from the tub during the drain and spin cycles for proper washer operation Resolves Samsung error codes 5C, SE, nd, 5E, FO2, and E5 caused by drain pump failure Rated 120V, 60Hz, 80W, 1.1A — correct electrical specifications for compatible Samsung top-load models 30-minute on / 30-minute off duty cycle — matches the operational requirements of compatible models Replaces DC97-19289A, DC97-19289B, DC97-17349B, DC97-17366A, DC97-17366J, and PX3516-01 Wire plug may differ from original — transfer harness from old pump if connector does not match Compatible with Samsung WA40 through WA54 series and Kenmore Samsung-built top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number DC97-19289F Also Replaces DC97-19289A, DC97-19289B (prior versions) Part Type Washer Drain Pump Assembly Condition Aftermarket Replacement Application Samsung Top-Load Washers Voltage 120V AC Frequency 60 Hz Wattage 80W Amperage 1.1A Duty Cycle 30 minutes on / 30 minutes off Error Codes Resolved 5C, SE, nd, 5E, FO2, E5 Connector Note Wire plug may differ — transfer harness from old pump if needed Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. Tilt the washer back or lay it on its side to access the drain pump at the bottom of the machine. Place towels and a shallow pan to catch residual water when the pump is disconnected. Note the wiring connector orientation before disconnecting — take a photo if needed. If the new pump's connector does not match the washer's harness, carefully transfer the wiring harness from the old pump to the new pump. Disconnect the drain hoses from the pump using pliers to loosen the clamps. Unscrew the pump mounting screws and remove the old pump. Install the new DC97-19289F pump in the same position, reconnect drain hoses and secure with clamps, and reconnect the wiring harness. Restore water supply and power, then run a drain cycle to verify proper drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan, towels. Frequently Asked Questions What error codes indicate a drain pump failure on Samsung washers? Error codes 5C, SE, nd, 5E, FO2, and E5 on Samsung top-load washers all indicate a drain fault — the washer was unable to drain within the expected time. These codes can also be caused by a clogged drain filter, blocked hose, or kinked drain line, so check those first. If the filter and hose are clear and the error persists after clearing them, the drain pump is the most likely cause. What is the difference between DC97-19289F, DC97-19289A, and DC97-19289B? These are successive revisions of the same Samsung drain pump assembly. DC97-19289A was the original version, DC97-19289B was an update, and DC97-19289F is the current version. Samsung issues revised part numbers when minor production changes are made — all three perform the same function and the DC97-19289F is the correct current replacement for any of the earlier versions. The DC97-17349B, DC97-17366A, and DC97-17366J are additional older cross-references for this pump used on earlier Samsung top-load models. Why might the wire plug on the new pump differ from the original? Samsung revised the wiring connector on this drain pump across different production runs. If the DC97-19289F pump you receive has a different connector than your washer's harness, do not force the connection. Instead, carefully remove the wiring harness from the old pump and transfer it to the new pump — both versions use the same internal terminals and the harness swap is straightforward. This is a known and documented step for this part and does not affect performance or safety. Should I check the drain filter before replacing the pump? Yes — always check and clean the drain filter and inspect the drain hose for kinks or blockages before replacing the pump. A clogged filter or blocked hose can cause the same error codes as a failed pump and clearing the blockage may resolve the problem without needing a new part. On Samsung top-load washers the drain filter is typically located at the bottom front of the machine. If the filter and hose are clear and the error persists, the pump needs replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications and performance of the original DC97-19289F drain pump assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11414076 Genuine OEM Whirlpool Dishwasher Circulation Pump Motor Assembly The W11414076 is a Genuine OEM Whirlpool replacement circulation pump and motor assembly compatible with a wide range of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea dishwashers. The circulation pump is the heart of the wash system — it pressurizes and delivers water to the spray arms, driving the jets that blast food and residue off your dishes throughout the wash and rinse cycles. When the circulation pump fails, cleaning performance collapses: dishes come out dirty or unrinsed, water pressure at the spray arms drops, and the machine may make loud droning or grinding noises. This is a complete circulation pump and motor assembly. Common causes of failure include worn motor bearings (which produce a continuous drone that gets louder over time), deteriorated impellers, and seal breakdowns. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W11414076 is the current production part that supersedes W11122133. It also replaces AP6980104, EAP12745416, PS12745416, 4958907, and OEM20940317. Note: this assembly does not include the drain pump — your existing drain pump transfers over to the new assembly during installation. Installs in 45–90 minutes with basic hand tools (the dishwasher must be pulled out and laid on its back to access the pump). Quick Answer The W11414076 Genuine OEM Whirlpool Dishwasher Circulation Pump Motor Assembly fixes Whirlpool, KitchenAid, Maytag, Jenn-Air, and Amana dishwashers where dishes come out dirty or unrinsed, water pressure at the spray arms is weak, water pools in the tub, or the motor makes a loud droning/grinding noise. Complete circulation pump + motor assembly. Genuine OEM. Current part superseding W11122133; also replaces AP6980104, EAP12745416, PS12745416, 4958907, OEM20940317. Before ordering: if the motor runs but water is weak, try cleaning the impeller filter screen first — see the FAQ. Common Problems This Part Fixes Dishes coming out dirty or unrinsed — circulation pump not delivering water to the spray arms Weak water pressure at the spray arms — impeller worn or motor failing Loud droning noise that gets louder over time — worn motor bearings Grinding or unusual noise during operation Water retention/pooling in the bottom of the tub Leaks from the pump housing — seal breakdown Motor humming but spray arms barely turning Reduced cleaning performance overall Motor not running at all — failed pump motor windings Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This circulation pump motor assembly directly replaces the following OEM and cross-reference part numbers: W11414076, W11122133, AP6980104, EAP12745416, PS12745416, 4958907, OEM20940321, AWP45352, PD00070783 W11414076 is the current OEM production part superseding W11122133. Contact our support team with your model number if you need confirmation before ordering. Compatibility This circulation pump motor assembly is compatible with select dishwashers from the following brands: Whirlpool dishwashers — select models (verify with your parts diagram) KitchenAid dishwashers — select models Maytag dishwashers — select models Jenn-Air dishwashers — select models Amana dishwashers — select models Magic Chef dishwashers — select models Admiral dishwashers — select models Norge dishwashers — select models Roper dishwashers — select models Kenmore / Sears dishwashers — select Whirlpool-built models Ikea dishwashers — select Whirlpool-built models This assembly may comprise several parts — refer to your specific parts diagram to verify included items. Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Circulation pump and motor assembly — pressurizes and delivers water to the spray arms for effective cleaning and rinsing Resolves "dirty dishes," "weak water pressure," "loud droning motor," "grinding noise," and "water pooling" symptoms when caused by pump failure Addresses the common failure modes: worn motor bearings, deteriorated impellers, and seal breakdowns Current OEM production part — directly supersedes W11122133 Also replaces AP6980104, EAP12745416, PS12745416, 4958907, and OEM20940317 Motor separates from the pump case with 3 Torx screws — some customers replace only the motor if the pump case is fine Drain pump is not included — your existing drain pump transfers to the new assembly Compatible with Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea dishwashers DIY repair — installs in 45–90 minutes with basic hand tools Product Specifications Part Number W11414076 Supersedes W11122133 Part Type Dishwasher Circulation Pump & Motor Assembly Condition Genuine OEM Application Dishwashers (Whirlpool platform) Function Delivers water to the spray arms for washing and rinsing Motor Attachment Separates from pump case with 3 Torx screws Drain Pump Not included — transfer your existing drain pump Location Bottom of dishwasher (access by laying unit on its back) Compatible Brands Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, Ikea Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Wear Work Gloves — Major Access Required Disconnect power at the breaker and shut off the water supply before beginning. Wear work gloves to protect your hands. This is a more involved repair because the circulation pump is on the bottom of the dishwasher. Throw the circuit breaker, remove the lower access panel, and open the electrical box to completely disconnect the electrical from the dishwasher. Disconnect the water supply line and the drain line. Remove the anchor screws securing the dishwasher to the counter, then pull the dishwasher out of the cabinet. Have a large towel ready — rotate the dishwasher and lay it on its back to access the pump on the bottom. Photograph everything before disconnecting. Disconnect all connections to the main circulation pump: the drain pump, the electrical connections, the leak-detection plate and circuit, and the water lines. Undo all clamps to the circulation pump. Remove the old circulation pump assembly. Transfer your existing drain pump to the new W11414076 assembly — it is not included. (If you're only replacing a noisy motor and the pump case is good, the motor separates from the case with 3 Torx screws and can be swapped on its own.) Install the new assembly, reconnect the drain pump, electrical connections, leak-detection plate, water lines, and all clamps, matching your photos. Stand the dishwasher back up, slide it into the cabinet, reconnect water/drain/electrical, and secure the anchor screws. Run a short test cycle and check for leaks. Note: use your dishwasher's onboard diagnostic function to confirm the pump was the issue — light/error codes vary by model, so check the quick guide that came with your specific dishwasher rather than relying on codes listed online for other models. Tools needed: Phillips screwdriver, Torx driver (T-set), nut driver, pliers, large towel, work gloves. Frequently Asked Questions The motor runs but water barely reaches the spray arms — do I definitely need a new pump? Maybe not — try this first, because it could save you the entire repair. On many KitchenAid/Whirlpool-platform dishwashers, there's a fine filter screen INSIDE the circulation pump on the impeller. This screen can clog with microplastics and fine food particles over time (sometimes after a surprisingly small number of wash cycles), which chokes off water flow even though the motor is running perfectly. The screen can look clean but still be blocked — a real-world test is to hold water in the mesh cup: if it holds water like a cup instead of draining freely, it's clogged. Cleaning it with a toothbrush restores full flow. To access it you do have to pull the pump (the same disassembly as replacing it, then 2 Torx screws to open the pump), so if you're already this far in, disassemble and inspect the screen BEFORE installing a new pump — you may find the old pump is perfectly good. Running a dishwasher-safe cleaning product through the machine first is also worth a try. My dishwasher motor is loud and getting louder — is that the pump? Yes, that's a classic sign of worn circulation pump motor bearings. The motor bearings wear out over time, and as they degrade they produce a continuous drone that steadily gets louder. Once the bearings have failed, the noise won't go away on its own and the motor should be replaced. On this assembly, the motor separates from the pump case with 3 Torx screws — some customers who only have a bearing/noise problem (and an otherwise good pump case) simply swap the motor and reuse the case. If you order the full assembly, you get both, and you can decide during the repair whether to swap just the motor or the whole thing. Does this come with the drain pump? No — the W11414076 is the circulation pump and motor assembly, and it does not include the drain pump. During installation, you'll transfer your existing drain pump from the old assembly to the new one (it detaches and reattaches). This is normal for this repair. If your drain pump is also failing (separate symptoms: won't drain, water left standing after the cycle), that's a different part you'd order separately. The circulation pump handles washing/spray pressure; the drain pump handles emptying the tub. What's the difference between W11414076 and W11122133? These are the same circulation pump assembly across production revisions. W11122133 was the earlier OEM part number, and W11414076 is the current production version that Whirlpool issued as its direct replacement. Both are physically and functionally interchangeable — if your dishwasher's parts diagram shows W11122133, the W11414076 is the correct current replacement, and this listing covers both. The cross-references AP6980104, PS12745416, and 4958907 are additional catalog identifiers for the same part. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same circulation pump and motor assembly installed in compatible Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, and Kenmore Whirlpool-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

AEB73764520 Genuine OEM LG Refrigerator Fan Grille Assembly The AEB73764520 is a genuine LG OEM fan grille assembly for LG refrigerators. This grille sits around the evaporator fan, holding and directing the air the fan pushes so cold air is guided evenly throughout the refrigerator and freezer compartments rather than dispersing unevenly right at the fan. It also serves a protective role, shielding the spinning fan blade from accidental contact while still allowing full, unrestricted airflow through its vents. Made of durable plastic, this grille can crack, warp, or break over time from the cold temperature cycling inside the freezer compartment, or from accidental impact during cleaning or organizing frozen food. A damaged grille typically shows up as uneven cooling or airflow within the compartment, since air isn't being properly guided and distributed, or in cases of significant damage, a fan blade that's no longer adequately shielded. Because parts that look similar can have small but meaningful differences in size and shape, it's important to confirm this exact part number matches your refrigerator before ordering, rather than relying on general appearance. Quick Answer The AEB73764520 Genuine OEM LG Refrigerator Fan Grille Assembly fixes LG refrigerators with a cracked, warped, or broken fan grille causing uneven cooling or airflow, or where the fan is no longer properly shielded. Genuine LG replacement part. Parts that look similar can have small but meaningful size and shape differences — always verify your exact model number before ordering. Common Problems This Part Fixes Uneven cooling or airflow within the refrigerator or freezer compartment Visible cracks, warping, or breakage in the grille around the evaporator fan Fan blade no longer adequately shielded due to grille damage Grille that has come loose or won't seat securely in place Reduced airflow efficiency affecting overall cooling performance Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers AEB73764520, 4952727, ALG53451, AP6873098, EAP12714296, PS12714296, PD00069980. We were not able to confirm additional cross-reference or superseding part numbers for this specific part from reliable sources at the time this page was built, so none are listed here rather than guessed. If you have a cross-reference number for your appliance, contact our support team and we will verify compatibility before you order. Compatibility This fan grille assembly is compatible with select LG refrigerators, including French door and Door-in-Door smart refrigerator models such as LFXS26973S, LFXS26596S, and LFXS28596S. Note: Parts that appear similar can have small but important differences in size and shape between LG refrigerator platforms. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine LG OEM part — factory-specified fit and airflow design Holds and guides air from the evaporator fan for even, consistent cold air distribution Resolves "uneven cooling," "poor airflow," and "cracked or broken grille" symptoms Also shields the fan blade from accidental contact Durable plastic construction Direct drop-in replacement matching the original mounting Compatible with select LG French door and Door-in-Door refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number AEB73764520 Part Type Refrigerator Fan Grille Assembly Condition Genuine OEM Brand LG Location Around the evaporator fan Function Guides evaporator fan airflow and shields the fan blade Material Plastic Quantity 1 fan grille assembly Compatible Brand LG Installation Notes ⚠️ Unplug Refrigerator Before Starting Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves to protect your hands. Access is typically through the freezer's rear interior panel: remove shelving and bins as needed, then remove the screws securing the back panel to expose the evaporator fan area where the grille is mounted. Photograph the grille's orientation and any mounting clips or screws before removing it. Carefully remove the old grille from around the fan, taking care not to contact the fan blade itself. Install the new AEB73764520 grille in the same position, securing any clips or screws to hold it firmly in place. Reassemble the back panel, restore power, and monitor the refrigerator over the next 24 hours to confirm even, consistent cooling has returned. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My cooling seems uneven, with some areas colder than others. Could this grille be the cause? Yes, this is possible if the grille is cracked, warped, or has come loose. This grille's job is to guide the evaporator fan's airflow evenly throughout the compartment, so damage or misalignment can cause cold air to concentrate in some areas while other spots don't get adequate circulation. Why does this part need to match my model so precisely? Fan grille assemblies that look very similar at a glance can have small differences in size and shape between different LG refrigerator platforms, since the grille has to fit precisely around the specific fan and duct assembly used in your model. Ordering based on a general resemblance rather than confirming your exact model number risks a poor fit that doesn't seat or seal correctly. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original mounting and airflow design of the fan grille assembly originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

🚪 XPARTCO 131658800 Dryer Door Catch This Door Catch is a replacement part for specific Kenmore, Frigidaire dryer models. It includes the door catch. This part ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently. Common causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly. Fix a loose or non-latching dryer door with this aftermarket replacement for part number 131658800. This dryer door catch holds the dryer door securely closed during operation to ensure proper airflow and drying performance. Designed to fit many Frigidaire, Kenmore, Electrolux, and Crosley dryers. ✅ Key Features: High-quality aftermarket replacement for part #131658800 Made from durable plastic for long-lasting use Designed to securely latch the door shut Simple snap-in installation — no tools required Helps prevent cycle interruption due to door opening 🔁 Replaces OEM Part Numbers: 131658800, 131658820, 131658845, 00634863, 07521419, 08015370, 134548000, 134548045, 3004967, 3202755, 3281055, 5303281055, 5307521419, 7521419, 835, AH418433, EA418433, F141735-000, F141735000, F62661-4, K1300884, K1301594, K1308079, K1309301, N8010215, Q0000401002, Q000504551, Q000504553, Q504551, Q504553, WQ504551, WQ504553, AP2107362, PS418433, WE01X25316, AP6037347, 4512762, PS11766999. ⚠️ Common Symptoms Fixed: Dryer door won’t stay closed Dryer won’t start due to open door switch Door pops open during a cycle Visible wear or damage to original catch 🧰 Compatible Brands: ✔️ Frigidaire✔️ Electrolux✔️ Kenmore (Frigidaire-built)✔️ Gibson✔️ Tappan✔️ Crosley✔️ White-Westinghouse 📌 Need help verifying compatibility? Send us your dryer’s model number — we’ll check it for you. 🚚 Why Buy from Parts-O-Matic? ✅ Reliable aftermarket performance ✅ Always Fast and Free U.S. shipping ✅ Easy DIY repair with trusted support ✅ Backed by excellent customer service 🛒 Fix your dryer’s latching issue today — order the 131658800 dryer door catch from Parts-O-Matic.com, and enjoy fast, free U.S. shipping!

Read more less

6601EN1003D Washer Door Lock Interlock Switch Replaces Part Numbers: 6601EN1003D, 6601ER1005A, 2651099, AH3636296, AP5594317, EA3636296, PS3636296.   This is an aftermarket part that can be used as a replacement for the OEM part. WARNING: California’s Proposition 65 (California Residents Only)

Read more less

WP3363394 Genuine OEM Washer Drain Pump  Direct Drive Washer Drain Pump for Whirlpool, Kenmore, Roper, Estate, Kirkland, and many more  Replaces Part Number: 3363394, 21024, 3296, 3348014, 3348015, 3348215, 3352492, 62516, 63347, 64076, 8235, AP6008107, PS11741239. This pump fits most direct drive washers. The pump outlet is about 1 1/4". The pump comes fully-boxed, brand new, in its original packaging.    

Read more less

XPARTCO W11130362 Washer Suspension Rod Kit The XPARTCO W11130362 is an aftermarket replacement suspension rod kit for Whirlpool top-load washers. The wash tub inside a top-load washer hangs suspended inside the cabinet, and this set of rods is what supports that tub and absorbs the vibration and movement it generates during unbalanced loads and high-speed spin. Without healthy suspension rods, the tub can bang against the cabinet, shake the whole machine, and produce loud, rhythmic noise that gets worse the more unbalanced a load is. This kit includes 4 suspension rods, 4 bushings, and 4 suspension balls, plus installation instructions — everything needed to replace the full suspension system in one job. Each steel rod measures approximately 23.3" long, with plastic components at the connection points. Over time, the bushings and balls wear down, and the rods themselves can lose their damping effectiveness, producing a loud banging or rattling noise often described as a "death rattle" during spin. It directly replaces W10594080, W10735786, W10748956, W10780040, W10821710, W10901056, W11027174, W11033491, W11228718, and W11035751. Quick Answer The XPARTCO W11130362 Washer Suspension Rod Kit fixes Whirlpool, Maytag, Kenmore, and Crosley top-load washers with loud banging, rattling, or a "death rattle" noise during spin, excessive tub movement, or a washer that feels unbalanced even after leveling. Complete kit: 4 rods, 4 bushings, 4 suspension balls. Each rod approx. 23" long. Replaces W10594080, W10735786, W10748956, W10780040, W10821710, W10901056, W11027174, W11033491, W11228718, W11035751. Replace all four rods together, even if only one has failed — uneven wear across the set reduces the effectiveness of the whole suspension system. Common Problems This Part Fixes Loud banging, knocking, or rattling noise during the spin cycle Washer tub that moves excessively or bounces during unbalanced loads Washer that shakes or "walks" even after the unit has been leveled Persistent rattling noise sometimes described as a "death rattle" Tub that wobbles noticeably when pushed by hand Noise that has gradually gotten worse over the years Washer that seems off-balance even with a properly distributed load Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer suspension rod kit directly replaces the following OEM and cross-reference part numbers: W11130362, W11027174, W10780040, W10594080, W10735786, W10748956, W10821710, W10901056, W11033491, W11228718, AP6262443, AWP43166, EAP12347546, PD00038547, PS12347546 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This suspension rod kit is compatible with select Whirlpool top-load washers, and also fits select Maytag, Kenmore, and Crosley top-load washers built on the same platform, including model numbers such as: WTW5000DW, WTW5000DW1, WTW5000DW2, WTW5000DW3 WTW5005KW MVWC565FW, MVWC565FW0, MVWC565FW1, MVWC565FW2 MVWX655DW, MVWX655DW1 MVWC555DW Note: Always verify your full model number before ordering, since Whirlpool uses different suspension systems across its top-load washer lineup. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement suspension rod kit — supports and dampens tub movement during spin Complete kit includes 4 suspension rods, 4 bushings, and 4 suspension balls Resolves "banging or rattling noise," "excessive tub movement," and "washer that feels unbalanced" symptoms caused by worn suspension Durable steel rods with plastic components at the connection points Each rod approximately 23.3" long Direct drop-in replacement — no modification required Replaces W10594080, W10735786, W10748956, W10780040, W10821710, W10901056, W11027174, W11033491, W11228718, and W11035751 Compatible with Whirlpool, Maytag, Kenmore, and Crosley top-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number W11130362 OEM Part Number W11130362 Part Type Washer Suspension Rod Kit Condition Aftermarket Replacement Application Whirlpool-Platform Top-Load Washers Kit Contents 4 suspension rods, 4 bushings, 4 suspension balls, installation instructions Rod Length Approx. 23.3 in. each Material Steel rods with plastic components Function Supports the tub and dampens vibration during spin Repair Difficulty Medium — basic hand tools and some disassembly required Quantity 1 kit (4 rods, 4 bushings, 4 balls) Compatible Brands Whirlpool, Maytag, Kenmore, Crosley Installation Notes ⚠️ Unplug Washer Before Starting — Replace All Four Rods Together Disconnect power at the outlet and shut off the water supply before beginning. Place a towel underneath the washer to protect the floor from any residual water. Wear work gloves. Open the lid and locate the suspension rod kit connecting the tub to the cabinet. Photograph how each old rod, bushing, and ball connects at both ends before removing anything, since these components are symmetrical around the tub and easy to reverse or mismatch. Use a flathead screwdriver to loosen the screws securing each rod assembly, then carefully pull each one free. Replace all four rods, bushings, and balls together, even if only one position shows obvious wear — the manufacturer specifically advises replacing the full set at once, since uneven wear across the suspension system reduces its overall effectiveness. Install each new rod assembly in the same position, making sure it fits snugly, and tighten the screws securely. Once all four are installed, gently rock the tub by hand to confirm even resistance at each corner before closing the lid. Restore water and power, then run a full spin cycle to confirm the noise and excess movement have resolved. Tools needed: flathead screwdriver, pliers, adjustable wrench, work gloves. Frequently Asked Questions My washer has a loud "death rattle" during spin. Will this kit fix it? Yes, this is one of the most common symptoms this kit resolves. Worn suspension rods, bushings, and balls lose their ability to dampen the tub's movement, and the result is often described as exactly this kind of loud, persistent rattling or banging during spin. Replacing the full suspension system typically restores quiet, stable operation. Do I really need to replace all four rods, or just the one that's broken? It's strongly recommended to replace all four together, and it's the manufacturer's own installation guidance for this kit. All four rods are typically the same age and under the same stress, so if one has worn out or broken, the others are likely not far behind. Replacing only one risks leaving the tub unevenly supported and having to repeat this repair again soon. My washer is off-balance even though it's level and the load looks even. Could this be the cause? Yes, this is a good sign to check the suspension system. If you bounce or push on the tub by hand and feel excessive movement or hear the tub knock against the cabinet even with a properly distributed load, worn suspension rods are a likely cause rather than a leveling or load-balance issue. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, materials, and mounting configuration of the original W11130362 suspension rod kit used in compatible Whirlpool, Maytag, Kenmore, and Crosley top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WE4M255 Dryer Genuine OEM Timer Resistor Replaces: WE4M255, 175D2886P001, 771346, WE04M0255, WE04X10029, WE4X10029, AH267964, EA267964, AP2044425, PS267964. Description: The Timer Resistor is a Genuine OEM part for specific GE dryers. It works in conjunction with the dryer's timer to regulate the duration of the drying cycle, ensuring that clothes are dried for the appropriate amount of time.

Read more less

W10335056 Washer Genuine OEM Water Level Switch Pressure Switch Replaces Part Numbers: W10335056, 1617123, 3366846, AH3408073, EA3408073, AP4566382, PS3408073, W10335056VP.  Description: This Pressure Switch is a Genuine OEM part for specific Whirlpool washing machine models. This part ensures your machine fills with the correct amount of water for the selected cycle, preventing overfilling or insufficient water levels that can lead to suboptimal washing results.    A faulty Pressure Switch can result from several issues, including clogging with detergent residue or debris, wear and tear from regular use, or electrical malfunctions affecting its responsiveness.     California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPWE9X105 Dryer Front Lower Felt Replaces Part Numbers:WE9X105, 277130, AH268338, AP2043044, EA268338, PS268338, WE09X0105   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

W11087376 Dishwasher Genuine OEM Pump and Motor Assembly Fits specific Whirlpool, Maytag, Kenmore Dishwasher models Description: This Dishwasher Pump & Motor is an OEM replacement part for specific Whirlpool dishwasher models. As the main component for water circulation, it contains both the water pump and motor required to power it. Replaces Part Numbers:W11087376, W10917114, 4534143, AP6237961, PS12074533. California Residents only WARNING: California’s Proposition 65 

Read more less