Search results for "washer Drain Pumps"

WD24X10018 Dishwasher Genuine Piston & Nut Assembly Replaces Part Numbers: WD24X10018, 821081, WD22X0133, WD22X133, WD24X0199, WD24X0220, WD24X199, WD24X220, AH260690, EA260690, AP2617344, PS260690. Description: This Piston & Nut Assembly is a Genuine parts for specific GE dishwasher models. It plays a critical role in the dishwasher’s water management system, helping to control water flow and ensuring proper drainage during the wash cycle. You should replace this piston & nut assembly if it becomes worn out or damaged. Common causes of a bad piston & nut assembly can include mineral buildup from hard water, general wear and tear from regular use, or physical damage due to debris or foreign objects in the dishwasher.

Read more less

XPARTCO DA82-01415A Refrigerator Water Leak Service Kit Water leak repair kit with updated internal duck bill. Fits select Samsung refrigerator models. Replaces Part Numbers: DA82-01415A, 3436781, AP5957964, PS10058968. Description: This Water Leak Repair Kit is a replacement part for select Samsung refrigerator models, this field service kit used to address water leakage and excessive frost in bottom freezer or French door refrigerators with dual evaporators. The kit includes a drain probe, two drain tubes, and two silver foam strips. With these parts, you can prevent excessive frost buildup on the evaporator cover and fix issues like water leaks under the crisper or odd fan noises that stop when the doors are opened.   This is an aftermarket part that can be used as a replacement for the OEM part

Read more less

5304517203 Genuine OEM Frigidaire Dishwasher Lower Spray Arm The 5304517203 is a genuine Frigidaire OEM lower spray arm for Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers. Positioned at the bottom of the dishwasher tub, this arm rotates as water is pumped through it, spraying water in all directions through its nozzle openings to clean dishes in the lower rack. It snaps directly into the bottom sump assembly and is essential for proper water distribution during the wash cycle. Made of durable plastic and metal, finished in gray/blue. Over time, the arm can crack, warp, or wear from general use and repeated exposure to hot water and detergent — high heat exposure in particular is a documented cause of failure. A broken or worn spray arm typically shows up as visible damage on the arm itself, dishes in the lower rack not getting cleaned properly, reduced or uneven water coverage, or the arm having difficulty rotating or getting stuck. It directly replaces 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623 Quick Answer The 5304517203 Genuine OEM Frigidaire Dishwasher Lower Spray Arm fixes Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers where the lower rack isn't getting cleaned properly, water coverage is reduced or uneven, or the arm won't rotate freely or has visible cracks. Snaps into the bottom sump assembly. Replaces 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623. After installing, confirm the arm spins freely by hand and doesn't contact the heating element before running a cycle. Common Problems This Part Fixes Dishes in the lower rack not getting cleaned properly Reduced or uneven water coverage during the wash cycle Spray arm that won't rotate freely or gets stuck Visible cracks, warping, or damage on the arm itself Arm that has come loose or detached from the sump assembly Clogged nozzle holes reducing water pressure and spray coverage Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher lower spray arm directly replaces the following OEM and cross-reference part numbers: 5304517203, 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lower spray arm is compatible with select Frigidaire dishwashers, and also fits select Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers built on the same platform. Note: Non-genuine versions of this exact part number are sold by several third-party sellers. A customer using a non-genuine version of this spray arm reported it came loose and broke during operation, so confirm you're ordering the genuine Frigidaire part rather than a lower-cost imitation. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified nozzle pattern and rotation fit Snaps directly into the bottom sump assembly for a secure, no-tools installation Resolves "not cleaning lower rack dishes," "uneven water coverage," and "won't rotate freely" symptoms Durable plastic and metal construction, gray/blue finish Approximate dimensions: 16.00" x 3.10" x 3.10" (L x W x H) Direct drop-in replacement — no modification required Replaces 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623 Compatible with Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 5304517203 Part Type Dishwasher Lower Spray Arm Condition Genuine OEM Brand Frigidaire Location Bottom of the dishwasher tub, in the lower sump assembly Material Plastic and metal Color Gray / Blue Dimensions Approx. 16.00" x 3.10" x 3.10" (L x W x H) Repair Difficulty Very Easy — no tools required Quantity 1 lower spray arm Compatible Brands Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, Kenmore Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — Confirm Clearance From The Heating Element Disconnect power to the dishwasher and shut off the water supply before beginning. Wear work gloves. Open the dishwasher and pull out the lower rack, setting it aside. Remove the old lower spray arm by releasing the locking tabs on each side and gently pulling it off the sump assembly. Snap the new 5304517203 spray arm onto the sump assembly in the same position. Before closing everything up, spin the arm gently by hand to confirm it rotates freely and does not make contact with the heating element — a real customer account described a spray arm and its support becoming loose and falling into the tub during use, so it's worth double-checking that the arm is fully and securely seated before running a cycle. Return the lower dish rack to its position and close the dishwasher door. Restore power and water, then run a test cycle to confirm the arm spins smoothly and dishes in the lower rack are getting properly cleaned. Tools needed: none. Frequently Asked Questions My dishes in the lower rack aren't getting clean. Is this the part I need? Yes, this is one of the most common symptoms of a worn or damaged lower spray arm. If the arm is cracked, clogged, or not rotating freely, water can't reach dishes in the lower rack evenly, leaving them dirty even when the upper rack comes out clean. I've read that a spray arm can come loose during operation. How do I prevent that? This has been reported, particularly with non-genuine imitation parts under the same number. To help prevent it, make sure the new arm snaps fully and securely onto the sump assembly during installation, and spin it gently by hand to confirm it's seated correctly and rotates without wobbling before running your first cycle with it installed. Do I need any tools to replace this spray arm? No. This is a simple snap-in, snap-out repair — release the locking tabs on the old arm to remove it, and press the new one onto the sump assembly until it clicks into place. No tools are required. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original nozzle pattern, dimensions, and sump connection of the lower spray arm originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

AEC74337401 Dishwasher Water Inlet Guide - Compatible with LG Dishwashers Product Description Restore your dishwasher’s cleaning performance with the AEC74337401 Water Inlet Guide from Parts-O-Matic. This genuine OEM replacement guide directs water from the inlet valve into the dishwasher tub, ensuring proper water flow for wash and rinse cycles. Designed for LG dishwashers, it fixes issues like insufficient water, poor cleaning, or water inlet error codes.  Note: Includes one water inlet guide. Take photos of connections during disassembly and clean the inlet valve before installation. Replaces part numbers: AEC74337401, AP6233501, PD00056036, PS12078211. Compatibility: Compatible with models including but not limited to: Verify your model number or contact Parts-O-Matic support for assistance. Key Features: ✅ Brand Compatibility: Fits select LG dishwasher models. 💧 Specifications: OEM plastic water inlet guide, designed for secure water flow and durability. 💰 Cost-Effective: OEM performance at a competitive price. 🛠️ Easy Installation: Requires a screwdriver, pliers, work gloves; typically installed in 20–30 minutes. 🛡️ Reliable Fixes: Resolves insufficient water, poor cleaning, or water inlet error codes. Installation Notes: Safety First: Unplug the dishwasher and turn off the water supply before installation to avoid shock or leaks. Clean the inlet valve and hose to prevent clogs. Access the inlet guide (inside or near the bottom of the dishwasher), disconnect the old guide, and install the new one, ensuring tight connections. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your dishwasher running smoothly today! Add to cart now for a budget-friendly fix!

Read more less

154728201 Dishwasher Sump Assembly   Replaces Part Numbers:154728201, AP4432731, PS2363522.    California Residents only: WARNING: California’s Proposition 65

Read more less

WD15X26078 Genuine OEM GE Dishwasher Water Inlet Valve The WD15X26078 is a Genuine OEM GE replacement dishwasher water inlet valve compatible with a wide range of GE, GE Profile, Café, Haier, Hotpoint, RCA, and Kenmore GE-built dishwashers. The water inlet valve is mounted at the base of the dishwasher behind the lower access panel, connecting the household water supply line to the dishwasher's fill circuit. When the control board calls for water during the fill phase, the valve's internal solenoid opens, allowing water to flow into the tub — and it closes the instant the call is dropped, stopping flow precisely at the correct fill level. Without a properly functioning inlet valve, the dishwasher can't fill correctly — leading to poor cleaning performance, error codes, or no wash at all. Rated 120V, 60Hz. Approximate dimensions: 3.75" H x 3.25" W x 3.00" L. Silver/multi-color metal and plastic construction with a deep-threaded, high-quality water inlet for a tight supply-line connection and a secure outlet design that keeps the internal fill hose firmly attached. As a Genuine OEM part manufactured by GE to factory specifications, the WD15X26078 directly replaces 4959029, AP6986683, PS16217027, EAP16217027, and PD00064270. Hard water sediment is a leading cause of inlet valve clogging and failure on GE dishwashers — if your old valve is restricted by mineral buildup, replacement (not cleaning) is the recommended fix, as the internal components are easily damaged during cleaning attempts. Installs in 20–30 minutes with basic hand tools. Quick Answer The WD15X26078 Genuine OEM GE Dishwasher Water Inlet Valve fixes GE, GE Profile, Café, Haier, Hotpoint, and Kenmore dishwashers that aren't filling with water, fill slowly, display the H2O error code, make strange noises or vibration during fill, won't stop filling, or leak from the valve area. 120V, 60Hz. Approx 3.75"H x 3.25"W x 3.00"L. Genuine OEM GE. Replaces 4959029, AP6986683, PS16217027, EAP16217027, PD00064270. Compatible with GDF, GDT, GDP, PDT, PDP, QDP, ZDT, DDT, and Café CDT series dishwashers. Common Problems This Part Fixes Dishwasher not filling with water at all — valve solenoid not opening Dishwasher filling slowly or not getting enough water — valve clogged with hard water sediment H2O error code displayed — insufficient water intake detected Strange noises or vibration during the fill phase — worn valve diaphragm Dishwasher won't stop filling — valve stuck open (overfill/flood risk) Water leaking from the valve area or its connections Dishes not being cleaned properly due to insufficient water fill Wash cycle interrupted or extended due to fill timeouts Valve inlet screen visibly clogged with mineral deposits Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers: WD15X26078, AGE846049, AP6986683, EAP16217027, PD00064270, PS16217027 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: some similar-looking GE valves (such as WD15X24213 or WD15X26140) are different parts — verify your original valve's part number or your dishwasher model number before ordering. Compatibility This water inlet valve is compatible with select dishwashers from the following brands: GE dishwashers — GDF series (GDF510PGM4BB/WW, GDF510PSM4SS/5SS, GDF511PSM5SS, GDF511PGM5WW, GDF530PGM4BB/CC/WW/5WW, GDF530PSM4SS/5SS, GDF530PMM4ES, GDF565SSN3SS, GDF630PFM4DS/5DS, GDF630PGM4BB/WW/5BB, GDF630PMM4ES/5ES, GDF630PSM4SS, GDF640HFM4DS, GDF640HGM4WW/5BB, GDF640HMM4ES, GDF645SGN2BB/WW/3BB/3WW, GDF645SMN2ES/3ES, GDF645SSN2SS/3SS and related) GE dishwashers — GDT series (GDT530PGP5BB, GDT530PSP5SS, GDT535PSMASS, GDT535PSM5SS, GDT565SSN2SS, GDT605PSM5SS, GDT630PFM4DS, GDT630PMM4ES/5ES, GDT630PYM4FS, GDT635HMM4ES, GDT635HSM4SS/5SS, GDT645SGN2BB/WW/3WW, GDT645SMN3ES, GDT645SSN2SS, GDT645SYN2FS, GDT665SBN2TS/3TS, GDT665SFN3DS, GDT665SGN2WW/3WW, GDT665SMN2ES, GDT665SSN3SS and related) GE dishwashers — GDP series (GDP615HFM4DS, GDP645SYN3FS/4FS/8FS, GDP665SYN2FS/3FS/4FS/8F7S and related) GE Profile dishwashers — PDT series (PDT715SBN2TS/3TS, PDT715SFN3DS, PDT715SMN2ES/3ES, PDT715SYN3FS, PDT775SYN2FS/3FS, PDT785SBN2TS, PDT785SYN2FS/3FS/5FS and related) GE Profile dishwashers — PDP series (PDP715SBN3TS, PDP715SYN3FS and related) GE dishwashers — QDP series (QDP555SBN4TS, QDP555SYN4FS and related) GE Monogram dishwashers — ZDT series (ZDT925SIN2II/3II/5II, ZDT925SPN2SS/3SS, ZDT925SSN2SS/3SS/5SS, ZDT985SIN3II, ZDT985SPN5SS, ZDT985SSN5SS and related) GE dishwashers — DDT series (DDT700SBN2TS/3TS, DDT700SFN2DS/3DS, DDT700SGN2BB/WW, DDT700SMN2ES and related) Café dishwashers — CDT series (CDT800P2N2S1-N5S1, CDT805M5N2S5-N4S5, CDT805P2N2S1-N5S1, CDT845M5N2S5-N5S5, CDT845P2N2S1-N5S1, CDT845P3N2D1-N5D1, CDT845P4N2W2-N5W2, CDT855M5N2S5/N3S5/N5S5, CDT855P2N2S1/N3S1/N5S1, CDT875M5N2S5-N7S5, CDT875P2N2S1-N5S1, CDT875P3N5D1 and related) Haier dishwashers (select models using the GE-platform valve) Hotpoint and RCA dishwashers (select GE-built models) Kenmore / Sears dishwashers (select GE-built models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Controls the flow of water into the dishwasher during fill cycles — precise fill for optimal cleaning performance Solenoid-actuated — opens when the control board calls for water and closes the moment the call is dropped Rated 120V, 60Hz — correct electrical specifications for compatible GE-platform dishwashers Approximate dimensions: 3.75" H x 3.25" W x 3.00" L Deep-threaded water inlet for a tight, leak-free supply line connection Secure outlet design keeps the internal fill hose firmly attached Resolves H2O error codes, no-fill, slow-fill, overfill, and fill-noise symptoms Replaces 4959029, AP6986683, PS16217027, EAP16217027, and PD00064270 Compatible with GE GDF/GDT/GDP series, GE Profile PDT/PDP series, QDP series, Monogram ZDT series, DDT series, Café CDT series, plus Haier, Hotpoint, RCA, and Kenmore GE-built dishwashers DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WD15X26078 Part Type Dishwasher Water Inlet Valve Assembly Condition Genuine OEM Application Dishwashers (GE platform) Voltage 120V AC Frequency 60 Hz Dimensions Approximately 3.75" H x 3.25" W x 3.00" L Color Silver / Multiple Colors Material Metal / Plastic Error Codes Resolved H2O (insufficient water intake) Compatible Brands GE, GE Profile, Café, Monogram, Haier, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power at the breaker and shut off the household water supply at the shutoff valve under the sink before beginning. Wear work gloves to protect your hands. Have towels and a shallow dish ready — residual water remains in the supply line and hoses and will spill when disconnected. Remove the lower access panel (baffle) at the front bottom of the dishwasher — typically 2–4 screws. Locate the water inlet valve where the household supply line enters the dishwasher. Photograph the hose and wire connections before disconnecting anything. Disconnect the household water supply line from the valve inlet (use pliers for the larger ingress connection — place the dish underneath to catch leftover water). Disconnect the internal fill hose from the valve outlet (needle-nose pliers help with the smaller egress hose clamp). Unplug the electrical connector that snaps onto the valve solenoid. Remove the mounting screws holding the valve bracket to the frame and lift the old valve out. Install the new WD15X26078 valve in the same position, secure the mounting screws, reconnect the internal fill hose with its clamp, and snap the electrical connector back on. Reconnect the household water supply line to the valve inlet — align the threads carefully and tighten snugly without over-torquing. Turn the water supply back on and use a flashlight to inspect all connections for leaks BEFORE reinstalling the access panel. Restore power and run a test cycle to confirm proper filling with no leaks. Tools needed: Phillips screwdriver, pliers, needle-nose pliers, shallow dish, towels, flashlight, work gloves. Frequently Asked Questions What does the H2O error code mean on my GE dishwasher? The H2O error code on GE dishwashers indicates the control board is not detecting sufficient water intake during the fill phase. Common causes are: a failed or clogged water inlet valve (the most frequent culprit), the household water supply shutoff valve partially closed, a kinked supply line, or low household water pressure. First verify the supply valve under the sink is fully open and the line isn't kinked. If the supply checks out, the WD15X26078 inlet valve is the standard fix — hard water sediment gradually clogs the valve's internal screen and passages, restricting flow until the dishwasher can't fill within its expected time window. Can I clean the old valve instead of replacing it? It's not recommended. While the inlet screen on some valves can be carefully brushed clean, the internal passages and solenoid diaphragm of a sediment-clogged valve are easily damaged during cleaning attempts — a common outcome is a valve that leaks or sticks open after being "cleaned," which risks flooding. Real-world experience (including customer stories with this exact part) shows that attempting to clean a hard-water-clogged valve often breaks it. Given the moderate cost of the OEM replacement versus the flood risk of a compromised valve, replacement is the reliable repair. If your area has hard water, consider this a maintenance item that may need periodic replacement. My dishwasher won't stop filling — is that also this valve? Yes — a valve stuck in the open position is the other failure mode. When sediment or a worn diaphragm prevents the valve from sealing fully closed, water continues to flow into the tub even when the control board has cut power to the solenoid. This can lead to overfilling and potentially flooding through the door or float overflow. If your dishwasher keeps filling past its normal level, or you find water accumulating in the tub between cycles, shut off the water supply at the sink immediately and replace the valve before running the dishwasher again. How do I know this is the right valve for my GE dishwasher? Check your dishwasher's model number (on a label along the door frame or tub edge) against the compatibility list above — the WD15X26078 covers a broad range of GE GDF, GDT, GDP, Profile PDT/PDP, QDP, Monogram ZDT, DDT, and Café CDT series dishwashers. Be aware that some similar-looking GE valves (such as WD15X24213 or WD15X26140) are different parts used on other model groups — they are not interchangeable with the WD15X26078. If your model isn't in the list or your original valve shows a different part number, contact our support team with your model number and we'll verify the correct valve before you order. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same water inlet valve installed in compatible GE, GE Profile, Café, Monogram, Haier, Hotpoint, RCA, and Kenmore GE-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

57271 Dishwasher Stainless Steel Water Fill Hose Stainless Steel Dishwasher Fill Hose 3/8" x 3/8"  4 Foot in Length.

Read more less

00770657 Genuine OEM Bosch Dishwasher Silverware / Cutlery Drawer The 00770657 is a genuine Bosch OEM cutlery drawer — a dedicated third-rack silverware caddy that sits in the upper interior of the dishwasher tub, above the top rack, on select Bosch dishwashers equipped with a third rack add-on compartment. Rather than loading silverware into a basket down in the lower rack, this drawer holds forks, spoons, and knives flat in their own dedicated level, laid out individually with room around each piece so water and detergent can reach every surface. It rides on durable rollers along rails built into the tub, sliding smoothly in and out for loading and unloading, and its position at the top of the tub gives it a clear, unobstructed line to the upper spray arm for targeted cleaning. The tray and support grid inside the drawer are open enough to let water flow freely through while still keeping utensils separated and organized. Because it's a lightweight tray sitting in a hot, wet, chemically active environment for years, common failure points include a metal frame that rusts through and eventually collapses under its own weight, plastic that becomes brittle or begins visibly disappearing from years of heat exposure, and dividers that crack or break, letting silverware jumble together. It directly replaces AP5788109, 00689507, 3279853, and PS8747441. As a genuine OEM part, the 00770657 is manufactured by Bosch to factory specifications — guaranteed fit, materials, and performance. Quick Answer The 00770657 Genuine OEM Bosch Dishwasher Silverware / Cutlery Drawer fixes Bosch (and compatible Thermador, Gaggenau, and select Kenmore) dishwashers with a third-rack cutlery drawer that has rusted through, has cracked or broken dividers, has become gummy or sticky and won't slide smoothly, or has cracks exposing silverware to the heating element below. Rides on rollers for smooth in-and-out extension. Replaces AP5788109, 00689507, 3279853, PS8747441. This is the roller-equipped cutlery drawer — a similar-looking companion part, 00770656, is a different drawer design without rollers, so double-check which one your dishwasher uses. Common Problems This Part Fixes Metal frame of the cutlery drawer rusted through or visibly corroding Drawer frame collapsing or sagging under the weight of silverware Missing or broken dividers letting silverware commingle instead of staying separated Drawer glides that have become gummy or sticky from food residue buildup, obstructing smooth movement Cracks or holes in the drawer exposing silverware to direct contact with the heating element Plastic that has become brittle, discolored, or is visibly disappearing after years of heat exposure Silverware not getting fully clean due to poor spray coverage from a warped or damaged drawer Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher cutlery drawer directly replaces the following OEM and cross-reference part numbers: 00770657, AP5788109, 00689507, 3279853, ABS12031, EAP8747441, PD00043732, PS8747441 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cutlery drawer is compatible with select Bosch dishwashers equipped with a third rack add-on compartment, and is also compatible with Thermador, Gaggenau, and select Kenmore dishwashers configured with a triple-rack setup, including model numbers such as: SHE68T52UC, SHE68T55UC, SHE68T56UC, SHE68TL5UC SHE863WF5N, SHE863WF6N SHP65T56UC, SHP65TL2UC SHV68T53UC, SHV68TL3UC, SHV863WD3N SHVM63W53N, SHXM63W55N, SHXM63WS5N Each of these models spans multiple production suffixes (such as /01, /02, /07, and /09) — check your full model and production number for exact confirmation. Note — check for rollers: This drawer rides on rollers. A similar-looking companion part, 00770656, is a separate cutlery drawer design used on other Bosch/Thermador/Gaggenau models without the roller mechanism. The two are not interchangeable. Check whether your existing drawer slides on visible rollers before ordering, and always verify your full model and production number. Contact our support team with your model number if you're unsure which drawer fits your dishwasher. Key Features Genuine Bosch OEM part — factory-specified frame, grid, and roller mechanism Dedicated third-rack cutlery drawer positioned above the top rack for optimal spray-arm targeting Resolves "rusted frame," "broken dividers," "sticky glides," and "cracked drawer" symptoms caused by wear and corrosion Multi-level basket layout keeps silverware separated for full surface exposure to wash spray Rides smoothly on rollers for easy extension and retraction when loading and unloading Open tray and support grid design allows water and detergent to flow through freely Direct drop-in replacement — no tools required, simply slides into place on existing rails Replaces AP5788109, 00689507, 3279853, and PS8747441 Compatible with Bosch, Thermador, Gaggenau, and select Kenmore third-rack dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 00770657 Part Type Dishwasher Third-Rack Cutlery / Silverware Drawer Condition Genuine OEM Brand Bosch Location Upper interior of the tub, above the top rack Mounting Rides on rollers along built-in tub rails Design Multi-level basket grid with open tray for water flow Repair Difficulty Very Easy — no tools required Quantity 1 cutlery drawer Compatible Brands Bosch, Thermador, Gaggenau, select Kenmore Installation Notes This is one of the simplest repairs in the entire dishwasher — no tools, no wiring, and no water lines to disconnect. Open the dishwasher door fully. Locate the existing cutlery drawer at the top of the tub, above the upper rack, and slide it forward and out along its rails until it clears the cabinet. Line up the new 00770657 drawer with the same rollers and rails, and slide it in until it seats fully at the back of the tub. Close the door and run a cycle to confirm the drawer sits securely and doesn't rattle or shift during operation. Frequently Asked Questions Does my drawer use rollers, or is it the other style? Slide your existing drawer out partway and look underneath or along the sides — this 00770657 drawer rides on visible roller wheels along the tub rails. If your drawer instead has a simpler glide track with no rollers, you likely have the companion part, 00770656, which is a different design used on other models. The two aren't interchangeable, so it's worth confirming before ordering. My drawer's metal frame has rusted through. Is that just cosmetic, or should I replace it? It's worth replacing rather than living with it. Once the metal frame starts rusting through, it typically continues to weaken and can eventually collapse under the weight of loaded silverware, sometimes suddenly. Customers who've dealt with this describe the original frame rusting to the point of failure over time — replacing it before it fully gives out avoids a mid-cycle collapse and keeps your utensils properly organized and exposed to the wash spray. Do I need any tools to install this? No. This is a genuinely tool-free repair — slide the old drawer out along its rails, then slide the new one in until it seats. Customers consistently describe this as one of the easiest dishwasher parts to swap. I see cracks or holes in my drawer near the bottom. Is that a safety concern? It can be, depending on where the damage is. If cracks or holes are positioned where silverware could shift down and make direct contact with the dishwasher's heating element, that's worth addressing rather than ignoring, since it can affect both the cleaning process and the condition of your utensils over repeated cycles. Replacing a cracked or holed drawer resolves this. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Bosch to factory specifications — guaranteed fit, materials, and performance. It matches the original roller mechanism, basket grid layout, and dimensions of the cutlery drawer originally installed in your third-rack-equipped Bosch, Thermador, Gaggenau, or compatible Kenmore dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

ERP DD62-00067A Dishwasher Water Valve Replaces Part Numbers:DD62-00067A, AP4341924, 1606674, PS4222444   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO DD62-00084A Dishwasher Water Valve – Compatible with Samsung Dishwashers Product Description Restore proper water flow and reliable cleaning performance with the XPARTCO DD62-00084A Dishwasher Water Valve. This Dishwasher Water Valve is an essential component for maintaining the optimal performance of your dishwasher. This replacement part ensures precise water flow control, allowing your dishwasher to operate efficiently and effectively. A faulty water valve can cause no water entering the dishwasher, slow filling, or poor cleaning performance. Replacing it with this dependable XPARTCO valve helps restore consistent water flow and efficient operation. XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and function. Replaces Part Numbers DD62-00084A, 2692215, ASM36078, EAP4222448, PD00002158, 737534554937, OEM15534663, AP5178218, PS4222448 Compatibility This replacement dishwasher water inlet valve fits select Samsung dishwashers. Common compatible models include (but are not limited to): Samsung DW80F600UTS Samsung DW80J3020US Always verify your dishwasher’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and water flow performance 💧 Accurate Water Fill Control – Ensures proper water levels for effective cleaning ⚙️ Fixes Common Issues – Resolves no-fill or slow-fill problems 💪 Durable Solenoid Valve – Designed for reliable long-term use 💰 Cost-Effective Repair – Affordable alternative to OEM valves ⚠️ Symptoms If your dishwasher is experiencing any of the following issues, this part may need replacement: ❌ Dishwasher not filling with water 💧 Slow or weak water flow ⚠️ Poor cleaning performance due to low water level 🔄 Cycle not starting properly 🚫 No water entering during wash cycle Replacing this water valve can restore proper dishwasher operation and cleaning efficiency. 📐 Product Specification Part Number: XPDD62-00084A Component Type: Dishwasher Water Inlet Valve Voltage: 120V AC Application: Dishwasher water supply system Mounting: Screw-mounted with hose connection Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, adjustable wrench ⚠️ Safety First: Disconnect power and shut off the water supply before servicing the dishwasher. Basic Steps: Turn off power and water supply. Remove the lower access panel. Disconnect water supply line and electrical connector. Remove mounting screws and remove the old valve. Install the new XPARTCO DD62-00084A valve. Reconnect water line and wiring. Restore power and water, then test for leaks and proper filling. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore reliable dishwasher performance — Add to Cart Now for a dependable repair!

Read more less

🚰 XPARTCO DD81-02265A Dishwasher Water Valve  🔁 Replaces These OEM Numbers: DD81-02265A, AP6244375, PS12085633 This Water Valve Assembly is a replacement part for specific Samsung dishwasher models. Crafted with high-quality materials, the water valve effectively controls the flow of water into your dishwasher, preventing leaks and ensuring precise water levels during each cycle. Installing this part can resolve common issues such as water not filling or leaking ✅ Key Features: Aftermarket alternative compatible with OEM part DD81-02265A 120 V, single solenoid valve with durable housing Controls precise water inlet timing and pressure for efficient cleaning Pre-tested to meet performance and leak-free operation standards Includes mounting bracket and standard hose port for easy installation 🔧 Solves Common Issues: Dishwasher not filling Slow or insufficient fill Water inlet-related error codes Leaks around valve assembly Humming valve with no water flow 🧰 Compatibility: Designed for specific Samsung dishwasher models 🚚 Why Shop at Parts-O-Matic? Trusted XPARTCO aftermarket quality at a great value Always Fast and Free U.S. shipping Dedicated support for part selection and validation Great fit for both DIY repairs and professional use 🛒 Prevent fill issues and get your dishwasher working right — order the XPARTCO DD81-02265A water valve now from Parts-O-Matic, shipped fast and free!

Read more less