XPARTCO 2188820 Refrigerator Thermistor (Sensor) Replaces WP2188820
The XPARTCO 2188820 is an aftermarket replacement refrigerator temperature sensor (thermistor) compatible with select Whirlpool, Kenmore, KitchenAid, Maytag, Jenn-Air, Dacor, and Thermador refrigerators. The thermistor is an NTC (negative temperature coefficient) sensor that continuously monitors the air temperature inside the refrigerator or freezer compartment and sends resistance-based readings to the electronic control board. The control board uses these readings to regulate compressor run time and fan operation, maintaining the set temperature accurately and efficiently.
This thermistor features an NTC resistance of 50K ohms at 25°C (27K ohms at 0°C/32°F) and a standard wire length of approximately 5.3 inches (13.46 cm), compatible with low-voltage refrigerator control boards (5V/12V). It directly replaces WP2188820, 2213442, AP6006068, PS11739132, and 1057764. Note: this thermistor is compatible with non-WISE system refrigerators only — it is not compatible with newer Whirlpool refrigerators using the WISE (Whirlpool Intelligent Smart Energy) control system. Installs in under 15 minutes.
Quick Answer
The XPARTCO 2188820 Refrigerator Thermistor fixes Whirlpool-family refrigerators that are too warm, too cold, have erratic temperatures, run the compressor too long, or display temperature-related error codes. NTC sensor, 50K ohm at 25°C, ~5.3" wire. Non-WISE system models only. Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Jenn-Air, Dacor, and Thermador. Replaces WP2188820, 2213442, AP6006068, PS11739132.
Common Problems This Part Fixes
Refrigerator not maintaining set temperature — too warm or too cold
Freezer section too warm or food not freezing properly
Compressor running continuously without cycling off
Temperature fluctuating erratically despite stable ambient conditions
Refrigerator temperature-related error codes displayed on the control panel
Excessive frost buildup caused by incorrect temperature regulation
Food or beverages freezing in the fresh food section
Replaces Part Numbers
This refrigerator thermistor directly replaces the following OEM and cross-reference part numbers:
WP2188820, 2188820, 2213442, EAP11739132, AWP46934, PD00033406, AP6006068, PS11739132.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This thermistor is compatible with select refrigerators from the following brands and series:
Whirlpool refrigerators — 5VW, GC3, EC3, GC5 series
Kenmore / Sears refrigerators — 106 series (Whirlpool-built models)
KitchenAid refrigerators — KSCS, KSSS, JS series
Maytag refrigerators (select models)
Jenn-Air refrigerators (select models)
Dacor refrigerators (select models)
Thermador refrigerators (select models)
Important — WISE System Compatibility: The 2188820 thermistor is compatible with non-WISE system refrigerators only. It is not compatible with newer Whirlpool refrigerators equipped with the WISE (Whirlpool Intelligent Smart Energy) control system. If your refrigerator uses the WISE system, this thermistor will not work correctly. Verify your model number before ordering, or contact our support team to confirm compatibility.
Key Features
NTC (negative temperature coefficient) thermistor — resistance decreases as temperature increases, allowing precise temperature monitoring
50K ohm resistance at 25°C (27K ohm at 0°C/32°F) — matches original WP2188820 specifications
Wire length approximately 5.3 inches (13.46 cm) — standard length matching OEM dimensions
Low-voltage design compatible with 5V/12V refrigerator control boards
Continuously sends temperature readings to the control board to regulate compressor and fan operation
Non-WISE system compatible only — verify your model before ordering
Direct replacement for WP2188820, 2213442, AP6006068, and PS11739132
Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Jenn-Air, Dacor, and Thermador refrigerators
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY repair — installs in under 15 minutes
Product Specifications
Part Number
2188820
OEM Part Number
WP2188820
Part Type
Refrigerator Temperature Sensor (NTC Thermistor)
Condition
Aftermarket Replacement
Sensor Type
NTC (Negative Temperature Coefficient)
Resistance at 25°C
50,000 ohms (50K ohm)
Resistance at 0°C (32°F)
27,000 ohms (27K ohm)
Wire Length
Approximately 5.3 inches (13.46 cm)
Voltage
5V / 12V (low voltage)
WISE System Compatibility
Non-WISE models only
Compatible Brands
Whirlpool, Kenmore, KitchenAid, Maytag, Jenn-Air, Dacor, Thermador
Installation Notes
⚠️ Unplug Refrigerator Before Starting Disconnect power before beginning. The thermistor location varies by model — it is typically clipped to a bracket on the interior side wall of the fresh food or freezer compartment, or mounted near the evaporator coil. Consult your model's parts diagram or service manual to confirm the exact location before disassembly. Open the sensor cover or unclip the sensor bracket, disconnect the wiring connector, and pull the old thermistor out. Insert the new 2188820 thermistor, reconnect the wiring connector, and snap the cover or bracket back into place. Ensure the sensor head is positioned close to the compartment wall and the wiring is not pinched. Restore power and monitor the refrigerator temperature over the next few hours to confirm stable, accurate cooling. Tools needed: Phillips screwdriver (for panel access on some models); no tools needed for sensor replacement itself.
Frequently Asked Questions
What is the difference between 2188820 and WP2188820?
These are the same thermistor. WP2188820 is the updated Whirlpool OEM part number that superseded the original 2188820. The 2213442 is also a cross-reference for the same part. This aftermarket replacement is compatible with all three numbers.
What does an NTC thermistor do and how do I know if mine has failed?
An NTC thermistor is a resistor whose resistance decreases as temperature increases. The control board sends a small voltage through the thermistor and measures the resulting resistance — a lower resistance means warmer temperature, and a higher resistance means cooler temperature. The board uses this reading to decide when to run the compressor and fans. A failed thermistor either reads open circuit (no continuity), short circuit (zero resistance), or provides incorrect readings that cause the refrigerator to run too warm, too cold, or cycle erratically. Test with a multimeter at room temperature — a working 2188820 should read approximately 50K ohms at 25°C (77°F). Significant deviation indicates failure.
How do I know if my refrigerator uses the WISE system?
The WISE (Whirlpool Intelligent Smart Energy) system was introduced on newer Whirlpool refrigerator models and uses a different thermistor specification that is not interchangeable with the 2188820. Models that use the WISE system are typically marked in the product documentation or on the control board. The easiest way to confirm compatibility is to verify your model number with our support team before ordering, or check whether WP2188820 appears in your model's official parts diagram. If your parts diagram lists WP2188820, this replacement is compatible.
Where is the thermistor located in my refrigerator?
The thermistor location varies by model and brand. On Whirlpool and KitchenAid models, it is commonly found on the interior side wall of the fresh food compartment clipped to a plastic housing. On some models it is located near the evaporator coil behind the freezer back panel. On Kenmore 106 series models, it may be on the fresh food section wall or inside the back panel. Consult your specific model's parts diagram or search for a model-specific installation video to locate the sensor before disassembling the refrigerator.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured with an NTC thermistor rated to the same 50K ohm specification as the original WP2188820 to match the performance and accuracy of the factory sensor.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
12638200000241 Genuine OEM Midea Dryer Drum Belt
The 12638200000241 is a Genuine OEM Midea replacement dryer drum belt compatible with a wide range of Midea, Criterion, and Insignia electric and gas dryers, including the MLE41/45/47/52, MLG45/52, MLTE37, CDE41, CDG41/45, CLADE67, and MDD160 series. The drum belt wraps around the dryer drum and the motor pulley, transferring the motor's rotation to spin the drum during the drying cycle. When the belt breaks, stretches, or wears out, the motor continues to run but the drum no longer spins — clothes sit still in the drum while the motor hums, and the dryer cannot complete a normal cycle.
As a Genuine OEM part manufactured by Midea to factory specifications, the 12638200000241 is constructed from durable black rubber. Packaged dimensions are approximately 11" L x 3" W x 2" H. Note: if the drum belt has failed, this is also a good opportunity to inspect the drum support rollers (Midea 12638000004021) and the idler/tensioner pulley assembly while the dryer cabinet is open — these components wear together and a failing roller or pulley can accelerate belt wear. Installs in 45–60 minutes with basic hand tools.
Quick Answer
The 12638200000241 Genuine OEM Midea Dryer Drum Belt fixes Midea, Criterion, and Insignia dryers where the motor runs but the drum doesn't spin, the belt has snapped or is visibly stretched, or where there's a burning rubber smell during operation. Black rubber drum belt. Packaged dimensions approximately 11" L x 3" W x 2" H. Genuine OEM. Compatible with Midea MLE41/45/47/52, MLG45/52, MLTE37, CDE41, CDG41/45, CLADE67, MDD160 series, plus Criterion CDE41N1AW/CDG41N1AW/CDG45N1AW and Insignia Midea-built models.
Common Problems This Part Fixes
Drum not spinning — belt has broken or slipped off
Motor runs and hums but the drum stays still
Drum spins intermittently — belt slipping under load
Burning rubber smell during operation — belt slipping on the motor pulley
Squealing or chirping noise during the drying cycle — belt frayed or stretched
Belt visibly cracked, frayed, broken, or missing inside the dryer cabinet
Extended drying times — drum not rotating at correct speed due to a worn belt
Replaces Part Numbers
This drum belt directly replaces the following part number:
12638200000241, AP7158561, PS18170626
This is the Midea manufacturer part number used across the compatible Midea, Criterion, and Insignia dryer platform. Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This drum belt is compatible with select Midea, Criterion, and Insignia electric and gas dryers, including:
Midea electric dryers — MLE41N1AWW, MLE45N1AWW, MLE45N1BWW, MLE45N3BMG, MLE45N3BWW, MLE47A3AGG, MLE47C3AWW, MLE47C4AWW, MLE47R5BWW, MLE52N3AWW, MLE52S7AGS, MLE52S7AWW
Midea gas dryers — MLG45N1AWW, MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AGS, MLG52S7AWW
Midea — MLTE37N1BWW, CLADE67W, MDD160A2301E1305 and related models
Criterion — CDE41N1AW (electric), CDG41N1AW (gas), CDG45N1AW (gas)
Insignia electric dryers — NSDRE67WH8A, NSFDRE67WH8A, NSFDRE67WH8AC, NSFDRE77WH8B, NSTDRE67W1, NSTDRE75W1
Insignia gas dryers — NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance
Wraps around the dryer drum and motor pulley to transfer the motor's rotation to spin the drum
Durable black rubber construction designed for continuous flex and motor load
Packaged dimensions: approximately 11" L x 3" W x 2" H
Compatible with the full Midea, Criterion, and Insignia electric and gas dryer platform
Often replaced along with the drum support rollers (Midea 12638000004021) and idler pulley assembly
Installs in 45–60 minutes with basic hand tools
Product Specifications
Part Number
12638200000241
Part Type
Dryer Drum Belt
Condition
Genuine OEM
Application
Electric and Gas Dryers (Midea platform)
Material
Rubber
Color
Black
Packaged Dimensions
Approximately 11" L x 3" W x 2" H
Often Replaced With
Drum Support Roller (Midea 12638000004021)
Compatible Brands
Midea, Criterion, Insignia
Installation Notes
⚠️ Unplug Dryer Before Starting (Shut Off Gas First on Gas Models) — Wear Work Gloves Disconnect power before beginning (and shut off the gas supply first if you have a gas dryer model). Wear work gloves — there are sharp sheet metal edges inside the dryer cabinet. Remove the lint filter housing screws, release the top panel locking clips with a putty knife, and lift the top panel. Disconnect the door switch harness and remove the front panel to access the drum, drive belt, and motor/idler pulley assembly. Take a photo of the existing belt routing before removing anything — this is essential for correct reassembly. Release the old belt from the idler pulley and slide it off the drum and motor pulley. Carefully lift the drum out and inspect the drum support rollers and idler pulley for wear — replace them now if needed while the dryer is open. Wrap the new 12638200000241 belt around the drum (ribbed side against the drum). Reinstall the drum, then route the belt around the motor pulley and under the idler pulley, allowing the idler to tension the belt. Reassemble the front panel and top panel in reverse order. Restore power (and gas, for gas models) and run a test cycle to confirm smooth, quiet drum rotation. Tools needed: Phillips screwdriver, putty knife, work gloves.
Frequently Asked Questions
How do I know if the drum belt has failed?
The clearest sign of a broken drum belt is a dryer where the motor starts and runs normally, but the drum does not spin — you'll hear the motor humming with no drum movement. If you open the door mid-cycle and the drum spins freely with no resistance (as if disconnected from the motor), the belt has either broken or slipped off completely. A stretched or worn belt that still drives the drum may also produce squealing or burning rubber smells from slippage on the motor pulley. Visually inspecting the belt after removing the dryer's front panel confirms the condition.
Should I replace the drum rollers and idler pulley at the same time?
Yes — since the dryer cabinet must already be opened and the drum removed to replace the belt, this is the ideal time to also inspect and replace the drum support rollers (Midea 12638000004021) and the idler/tensioner pulley. All three components form the drum drive system and tend to wear together. A worn roller or pulley is often what caused the belt to fail prematurely in the first place. Addressing them together in a single repair eliminates the most common drum drive failure points and prevents a near-term repeat teardown.
Does this belt fit Insignia and Criterion dryers as well as Midea?
Yes — Insignia (Best Buy) and Criterion (Sears/Kmart) are house brands whose dryers in this size class are manufactured by Midea and use the same internal components, including this drum belt. Confirmed compatible models include Insignia NSDRE67WH8A, NSFDRE67WH8A, NSFDRE77WH8B, NSTDRE67W1, NSTDRE75W1 (electric) and NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1 (gas), plus Criterion CDE41N1AW (electric) and CDG41N1AW/CDG45N1AW (gas). Always verify your specific model number before ordering.
Which way does the belt go around the drum — ribbed side in or out?
On the drum belt, the ribbed (grooved) side should face inward, against the drum surface, while the smooth side faces outward. The ribs grip the smooth drum surface to drive it as the motor pulley turns. On the motor pulley side, the belt seats in the grooves of the small motor pulley. Take a photo of how the original belt was routed before removing it — this is the most reliable way to confirm correct orientation during reinstallation.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same drum belt installed in compatible Midea, Criterion, and Insignia electric and gas dryers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
Deflecto UBGWB Universal Bird Guard Dryer Vent Cover 3"-4" (White) - Fits Most 3" or 4" Dryer and Bathroom Vents
Product Description
Protect your dryer or bathroom exhaust vent with the Deflecto UBGWB Universal Bird Guard Dryer Vent Cover in White. Designed to fit over any 3" or 4" vent hood, this durable, weather-resistant cover prevents birds, rodents, and debris from entering or nesting, ensuring efficient airflow and reducing fire hazards. Made of UV-resistant plastic, it self-cleans with wind or rain, offering long-lasting protection for both residential and commercial applications.
Note: Includes one bird guard cover. Disconnect power and gas (if applicable) before installation. Check guard periodically for lint or debris buildup.
Replaces part numbers: UBGWB, UBGBB, PBH50WZW, AP4246336, 1370849
Compatibility:
Compatible with most 3" or 4" dryer and bathroom exhaust vent hoods, including but not limited to:
Whirlpool, Maytag, Kenmore, GE, Samsung, LG, Frigidaire, Bosch dryers
Standard bathroom exhaust vents (3" or 4" diameter)
Universal fit for most major brand vent hoods
Verify your vent hood size or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits most 3" or 4" dryer and bathroom exhaust vent hoods from major brands.
🛡️ Specifications: UV-resistant plastic bird guard, fits 3" or 4" vent hoods, self-cleaning design.
💪 Reliable Performance: Durable and weather-resistant, prevents pests and debris entry.
🛠️ Easy Installation: Requires screwdriver; typically installed in 5–10 minutes.
🔥 Effective Protection: Reduces lint buildup and fire hazards while maintaining airflow.
Product Specification
Part Number: Deflecto UBGWB
Component Type: Universal bird guard dryer vent cover
Material: UV-resistant plastic
Dimensions: 7.25" H x 7.25" W x 4.5" D
Weight: 9.6 oz (Based on web:0)
Mounting: Fits over 3" or 4" vent hoods, secured with screws
Operating Conditions: Suitable for outdoor dryer and bathroom exhaust vent environments
Compliance: Prop 65 warning for California
Installation Notes:
Safety First: Disconnect the dryer from the power source and gas supply (if applicable) before installation.
Shop for high-quality appliance accessories with a 30-day return policy. Keep your dryer vent safe and efficient today!
Add to cart now for reliable protection!
XPARTCO 4561EL3002A Dryer Idler Pulley Assembly
The XPARTCO 4561EL3002A is an aftermarket replacement dryer idler pulley assembly compatible with select LG and Kenmore electric and gas dryers. The idler pulley assembly is a spring-tensioned arm, pulley wheel, and spring kit that presses against the drive belt to keep it under constant tension as it wraps around the drum and motor pulley. Without correct belt tension, the belt slips, the drum stops spinning, and the dryer tumbles clothes poorly or not at all. A worn idler pulley bearing is also one of the most common causes of squealing, squeaking, and thumping noises in LG dryers.
This complete assembly includes the idler arm, pulley wheel, and idler spring. Overall dimensions are 5-3/4"L x 2-1/4"W x 3-7/8"H with a 2-1/4" diameter pulley wheel. Constructed from plastic and metal in white, black, and gray. It directly replaces 4561EL3002B, DE3002A, 4980EL3004, 1267530, AP4438243, AH3523033, EA3523033, EAP3523033, PD00001729, and PS3523033. Note: the pulley wheel only (without arm and spring) is sold separately as APN4560EL3001A — this listing is for the complete idler assembly. Often replaced together with the drum belt (4400EL2001A) and drum rollers (4581EL2002A) for a complete drum drive repair. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The XPARTCO 4561EL3002A Dryer Idler Pulley Assembly fixes LG and Kenmore dryers that are squealing, thumping, or where the drum has stopped spinning because belt tension is lost. Complete assembly — idler arm, pulley wheel, and spring included. 5-3/4"L x 2-1/4"W x 3-7/8"H overall; 2-1/4" pulley diameter. Replaces 4561EL3002B, DE3002A, 4980EL3004, 1267530, AP4438243, AH3523033, EAP3523033, PS3523033. Often replaced with drum belt (4400EL2001A) and drum rollers (4581EL2002A).
Common Problems This Part Fixes
Drum not spinning — belt has lost tension and slipped off
Loud squealing or squeaking noise during the drying cycle — worn idler pulley bearing
Thumping or clunking noise as the pulley wheel wobbles on a worn axle
Belt repeatedly falling off after reinstallation — idler no longer maintaining tension
Grinding noise from the idler area — bearing completely failed
Drum spinning intermittently due to inconsistent belt tension
Idler arm visibly cracked or pulley wheel no longer spinning freely by hand
Replaces Part Numbers
This idler pulley assembly directly replaces the following OEM and cross-reference part numbers:
4561EL3002A, 1267530, 4561EL3002B, ALG51226, AH3523033, AP4438243, EA3523033, EAP3523033, PD00001729, PS3523033
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This idler pulley assembly is compatible with select LG and Kenmore gas and electric dryers:
LG electric dryers — DLE series (DLE0442W, DLE1001W, DLE2250W, DLE2350W, DLE3133W, DLE3777W, DLE4801W, DLE5001W, DLE5955W, DLE7177WM and related models)
LG electric dryers — DLEX series (DLEX3885W, DLEX5780VE and related models)
LG gas dryers — DLG series (DLG0452W, DLG2251W, DLG2351W, DLG3744W, DLG3788W, DLG5002W, DLG5966W and related models)
LG gas dryers — DLGX series (DLGX3886W and related models)
Kenmore / Sears dryers — 796-series (LG-built electric and gas models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Complete idler pulley assembly — includes idler arm, pulley wheel, and idler spring
Maintains correct drive belt tension so the drum spins smoothly and quietly during every drying cycle
Overall dimensions: 5-3/4"L x 2-1/4"W x 3-7/8"H; pulley wheel diameter: 2-1/4"
Plastic arm and housing with metal pulley shaft — durable construction for continuous operation
Replaces 4561EL3002B, DE3002A, 4980EL3004, AP4438243, AH3523033, EAP3523033, and PS3523033
Note: pulley wheel only (without arm and spring) is sold separately as APN4560EL3001A — this listing is the complete assembly
Often replaced together with drum belt (4400EL2001A) and drum rollers (4581EL2002A)
Compatible with LG DLE, DLEX, DLG, DLGX series and Kenmore 796-series dryers
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
XP4561EL3002A
Also Replaces
4561EL3002B (prior revision)
Part Type
Dryer Idler Pulley Assembly (Arm, Wheel, and Spring)
Condition
Aftermarket Replacement
Application
LG and Kenmore Gas and Electric Dryers
Overall Dimensions
5-3/4"L x 2-1/4"W x 3-7/8"H
Pulley Wheel Diameter
2-1/4 inches
Material
Plastic / Metal
Color
White / Black / Gray
Includes
Idler arm, pulley wheel, and idler spring — complete assembly
Pulley Wheel Only
APN4560EL3001A (sold separately — not this listing)
Often Replaced With
4400EL2001A Drum Belt, 4581EL2002A Drum Rollers
Compatible Brands
LG, Kenmore (LG-built)
Installation Notes
⚠️ Unplug Dryer Before Starting — Wear Work Gloves Disconnect power (and shut off gas for gas dryers) before beginning. Wear work gloves — there are sharp sheet metal edges inside the LG dryer cabinet. Access the idler pulley by removing the back panel of the dryer (on most LG models) or the front panel and top panel. Take a photo of the belt routing around the drum, motor pulley, and idler pulley before removing anything — this is essential for correct reassembly. Release belt tension by pressing the idler arm toward the motor and sliding the belt free. Remove the idler spring from its anchor point, then unclip or unscrew the idler arm from its mounting bracket. Install the new 4561EL3002A idler assembly in the same position — hook the spring onto its anchor point first, then mount the arm. Re-route the belt around the drum (ribbed side in), under the idler pulley, and around the motor pulley, then allow the idler arm to tension the belt. Reassemble panels, restore power, and run a test cycle. Tip: while the dryer is open, inspect and replace the drum belt (4400EL2001A) and drum rollers (4581EL2002A) if worn. Tools needed: Phillips screwdriver, Torx screwdriver (T20 on some models), needle-nose pliers, work gloves.
Frequently Asked Questions
What does the dryer idler pulley do?
The idler pulley is a spring-loaded arm and wheel assembly that presses against the drive belt between the drum and the motor pulley, keeping the belt under constant tension. This tension is what allows the belt to grip both the drum surface and the motor pulley so the motor's rotation is transmitted to spin the drum. Without proper tension — or with a pulley bearing that has seized or worn out — the belt slips, the drum stops spinning, and the dryer produces heat without tumbling clothes. A worn bearing also creates the high-pitched squealing noise that is the most recognizable symptom of idler pulley failure on LG dryers.
What is the difference between 4561EL3002A and 4561EL3002B?
These are the same LG dryer idler pulley assembly across two production revisions. The 4561EL3002B was an earlier version and the 4561EL3002A is the current part number. Both are the same functional assembly — if your dryer's parts diagram shows 4561EL3002B, the 4561EL3002A is the correct current replacement and is covered by this listing.
Should I also replace the drum belt and rollers at the same time?
Yes — since the dryer must be disassembled to replace the idler pulley, this is the ideal time to also inspect and replace the drum belt (4400EL2001A) and drum support rollers (4581EL2002A). All three parts form the drum drive system and wear at similar rates. A worn roller or belt is often what caused the idler pulley to wear prematurely. Replacing all three in one repair eliminates the most common drum drive failure points and prevents a repeat teardown in the near future.
Can I just replace the pulley wheel without the arm and spring?
Yes — the pulley wheel alone (without the arm and spring) is sold separately as part number APN4560EL3001A. If only the wheel bearing has failed and the arm and spring are in good condition, you can order just the wheel. However, if the arm is cracked, the spring has lost tension, or both the wheel and arm have significant wear, ordering the complete 4561EL3002A assembly is more cost-effective and ensures the entire idler system is renewed in a single repair.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from plastic and metal to match the dimensions and performance of the original 4561EL3002A idler pulley assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPHVP-16 Microwave Convection Oven High Voltage Diode – Replaces TurboChef 100481 – Compatible with Commercial & Residential Microwave Models
Product Description
Restore proper heating performance in your commercial or residential microwave with the XPHVP-16 Microwave Convection Oven High Voltage Diode. This high-quality aftermarket diode replaces TurboChef 100481 and is engineered to handle the elevated heat and voltage levels found in high-speed ovens and convection microwave systems. A failing HV diode can cause the microwave to run without heating, blow fuses, or produce loud humming sounds. Installing this XPHVP-16 diode restores safe high-voltage operation and consistent heating.
Replaces Part Numbers
XPHVP-16, TurboChef 100481, HV07-16, HVP-16, TBC100481, CKTE100481 equivalent high-voltage microwave diodes.
Compatibility
This aftermarket high-voltage diode replaces TurboChef 100481 and fits many commercial and household microwave or convection microwave ovens, including:
Fits specific TurboChef models including Bullet, ECO ST, Encore, Encore 2, G5, I3, NGC, NGC2, NGO, Sota/I1, TORNADO 2, i5.
Typical compatible equipment includes:TurboChef High-Speed Ovens, and other convection microwave systems requiring a 12–16kV diode.
Always verify electrical specifications before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Designed to replace TurboChef 100481 and match OEM electrical performance
🔥 High-Heat & High-Voltage Rated – Built for demanding commercial microwave environments
💰 Cost-Effective Commercial Repair – A reliable alternative to costly OEM replacement parts
🛡️ Solves Common Issues – Fixes no-heat conditions, humming, blown fuses, and weak heating output
📐 Product Specification
Part Number: XPHVP-16
Replaces: TurboChef 100481
Component Type: High Voltage Rectifier Diode
Voltage Rating: 12–16 kV peak
Current Rating: Max. Forward Current 750MA
Polarity: Standard microwave HV polarity (stripe = cathode)
Material: Heat-resistant high-voltage diode with insulated leads
Compliance: Built to OEM-equivalent quality standards (not OEM)
🛠️ Installation Notes
Tools Needed: Screwdriver, insulated gloves, needle-nose pliers
⚠️ Safety First: Microwave and commercial oven repairs involve dangerously high voltage even when unplugged. Only qualified technicians should replace HV components.
Steps (for trained professionals):
Disconnect power and properly discharge the HV capacitor.
Remove the microwave or oven’s service cover.
Locate the HV diode near the capacitor and transformer.
Remove the old diode and install the new XPHVP-16, ensuring correct polarity.
Reassemble unit and test heating performance.
⏱️ Time Required: 20–30 minutes (professional repair recommended)
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Appliance & Commercial Equipment Parts Supplier
🔄 30-Day Return Policy
Restore powerful, consistent heating — Add to Cart Now for a reliable and cost-effective replacement!
WP661566 Dishwasher Genuine High Limit Thermostat
Replaces Part Number: WP661566, 661566, W10339474, 2887, 3369777, 3370783, 3371618, 4171694, WP661566VP, AP6010246, PS11743423.
Description: The High Limit Thermostat is a Genuine OEM part for specific Kenmore, Whirlpool dishwasher models. This safety feature is designed to prevent the dishwasher from overheating by shutting off the power if the internal temperature exceeds a certain limit. It acts as a safeguard against potential hazards, such as fires, and ensures the dishwasher operates within safe temperature ranges.
XPARTCO Y54414 Dryer Idler Pulley Wheel – Replaces WPY54414 – Compatible with Maytag, Whirlpool & Kenmore Dryers
Product Description
Restore proper belt tension and smooth drum rotation with the XPARTCO Y54414 Dryer Idler Pulley Wheel. This high-quality aftermarket replacement pulley maintains tension on the dryer drum belt, ensuring consistent tumbling during drying cycles.
A worn or damaged idler pulley wheel can cause squealing noises, belt slippage, drum not turning, or uneven drying. Replacing it with this durable XPARTCO pulley helps eliminate noise issues and restore reliable dryer performance at a cost-effective price.
XPARTCO provides trusted aftermarket appliance parts engineered to match original fit and function.
Replaces Part Numbers
WPY54414, Y54414, 14218926, 54414, R0609504, WPY54414VP, 54414-REPL, R0609504-REPL, AP6024203, PS11757553, D510142P, 510142P, 510142, D510142, 510142P, 510142, 54414, 54415, 54415P, AP6329060, PS17001032, DE407, 54414-2, 1246423, AP6024203, EAP11757553, PD00002420, PS11757553, 510142P, 510142, D510142P, AP4291235, PS2200898
Compatibility
This replacement dryer idler pulley wheel fits select Maytag, Whirlpool, Kenmore (Whirlpool/Maytag-manufactured), Amana, Estate, and Crosley dryers.
Common compatible models include (but are not limited to):
Maytag MEDC215EW
Whirlpool WED4815EW
Kenmore 110.60612990
Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Matches OEM fit and belt alignment
🌀 Maintains Proper Belt Tension – Ensures smooth drum rotation
🔇 Reduces Squealing & Noise – Replaces worn or noisy pulley wheels
💪 Durable Bearing Design – Built for long service life
💰 Cost-Effective Repair – Affordable alternative to OEM idler pulleys
📐 Product Specification
Part Number: Y54414
Component Type: Dryer Idler Pulley Wheel
Material: Metal wheel with durable bearing
Application: Dryer drum belt tension system
Mounting: Shaft-mounted on idler arm
Quality Level: Aftermarket replacement (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, nut driver
⚠️ Safety First: Unplug the dryer before servicing to avoid electrical shock.
Basic Steps:
Disconnect dryer power.
Remove top and front panels to access drum (model dependent).
Release belt tension and remove the old pulley wheel.
Install the new XPARTCO Y54414 pulley onto the idler arm.
Re-route the belt around the motor pulley and idler.
Reassemble the dryer and test operation.
⏱️ Time Required: 30–45 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Aftermarket Appliance Parts
🔄 30-Day Return Policy
Eliminate dryer noise and restore smooth tumbling — Add to Cart Now for a reliable, budget-friendly repair!
ERP W10547292 Dryer Idler Pulley
Replaces Part Numbers: WPW10547292, W10547292, 2683183, 8547160, WPW10547292VP, AP6022817, PS11756154.
Description: This Idler Pulley Wheel & Arm Assembly is a replacement part for select Whirlpool dryer models. The W10547292 is a dryer tension idler pulley, commonly used in select Whirlpool dryer models. This part helps maintain the proper tension on the dryer belt, ensuring smooth and efficient operation of the dryer. It is compatible with various models.
This is an aftermarket part that can be used as a replacement for the OEM part.
691366 Dryer Idler Pulley - Compatible with Whirlpool, Kenmore, Maytag, KitchenAid
Product Description
Keep your dryer running smoothly with the 691366 Dryer Idler Pulley. This replacement idler pulley is designed as a replacement for select Whirlpool, Kenmore, Maytag, KitchenAid, and other compatible dryers, offering a cost-effective alternative to the original. It maintains proper tension on the drive belt to ensure the dryer drum spins correctly, preventing issues like belt slippage or drum failure. This part addresses symptoms such as the dryer not tumbling, making unusual noises (e.g., squeaking or squealing), failing to start, or taking too long to dry, often caused by a worn or broken idler pulley.
Note: Includes (1) idler arm and pulley assembly. Disconnect power before installation. Verify compatibility with your dryer model.
Replaces part numbers: WP691366, 691366, 239477, 26000691366, 337116, 337407, 337510, 3388345, 338946, 3394332, 347034, 347226, 347277, 4319391, 688166, 691366BULK, 8207, 99989677, DE412, K35-163, W10612905, WP691366VP, PD00002256, EAP11743765, AP6010582, PS11743765.
Compatibility:
Compatible with select dryer models, including but not limited to:
Whirlpool: WED4815EW1, WED4850BW0, WED6600VU0, 1CWGD5790VQ0, 7EWED1510YM0
Kenmore: 110.77322600, 110.77432600, 110.72832101, 110.60022010
Maytag: MED5630TQ0, 4KMED5700TQ0, 7MMEDC300BW0
KitchenAid, Amana, Inglis, Roper, Crosley, Estate, Admiral, Magic Chef: Various models (verify with model number)
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Roper, Crosley, Estate, Admiral, and Magic Chef dryers.
🔧 Specifications: High-quality plastic pulley with metal idler arm.
💪 Reliable Performance: Ensures proper belt tension for smooth drum rotation and efficient drying.
🛠️ Easy Installation: Requires screwdriver, nut driver, pliers; typically installed in 20–30 minutes.
🛡️ Effective Fixes: Resolves issues like no tumbling, noisy operation, failure to start, or prolonged drying times.
Product Specification
Part Number: 691366
Component Type: Dryer idler pulley
Material: Plastic pulley, metal idler arm
Compliance: Prop 65 warning for California
Installation Notes:
Safety First: Disconnect the dryer from the power source before installation.
Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running efficiently today!
Add to cart now for a reliable fix!
XPHVC1095 Microwave High Voltage Capacitor, 2100 VAC, 0.95 µF – Universal Microwave Replacement
Product Description
Restore proper microwave heating performance with the HVC1095 Microwave High Voltage Capacitor (2100 VAC, 0.95 µF). This high-quality aftermarket capacitor stores and releases electrical energy required by the high-voltage circuit to power the magnetron. A faulty capacitor may cause the microwave to stop heating, hum loudly, or trip breakers. Replacing it with this reliable XPHVC1095 capacitor helps restore efficient heating and safe microwave operation.
Compatibility
This universal microwave high-voltage capacitor is compatible with many GE, Whirlpool, Samsung, LG, Frigidaire, Panasonic, Sharp, and Kenmore microwave ovens that require a 2100 VAC, 0.95 µF capacitor.
Commonly used in countertop, over-the-range, and built-in microwave models.
Always verify voltage and capacitance requirements before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Built to OEM-equivalent electrical specifications
⚡ 2100 VAC, 0.95 µF Rating – Supports proper magnetron operation
🔥 Restores Heating Function – Fixes microwave running but not heating
💪 Heavy-Duty Construction – Designed for high-voltage applications
💰 Cost-Effective Repair – Reliable alternative to OEM microwave capacitors
📐 Product Specification
Part Number: XPHVC1095
Component Type: Microwave High Voltage Capacitor
Voltage Rating: 2100 VAC
Capacitance: 0.95 µF (microfarad)
Application: High-voltage power supply circuit, (4.8 mm) 2 male terminals, Oval Shape
Mounting: Bracket-mounted
Quality Level: Aftermarket replacement (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, insulated pliers
⚠️ Safety First:WARNING: This high-voltage capacitor is for microwaves. High-voltage capacitor is an electric device that holds a charge of electricity in the high-voltage circuit of the microwave. Because high-voltage capacitors in a microwave can retain a lethal electrical charge even when the microwave is unplugged, a service technician should install this part.
Basic Steps:
Unplug the microwave.
Remove the outer cabinet.
Safely discharge the existing capacitor.
Disconnect wiring and remove the old capacitor.
Install the new HVC1095 capacitor securely.
Reconnect wiring, reassemble the cabinet, and restore power.
Test microwave heating operation.
⏱️ Time Required: 20–30 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Aftermarket Appliance Parts
🔄 30-Day Return Policy
Restore microwave heating safely and efficiently — Add to Cart Now for a dependable, budget-friendly repair!
XPARTCO 279640 Dryer Idler Pulley
The XPARTCO 279640 is an aftermarket replacement dryer idler pulley (also called a belt tension pulley wheel) compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Crosley, Inglis, and Admiral. The idler pulley is spring-tensioned against the drive belt to maintain correct tension as the belt wraps around the drum — allowing the drum to rotate smoothly and quietly. When the idler pulley bearing wears out, the belt loses proper tension and the dryer begins making squealing, squeaking, or clunking noises, and the drum may eventually stop spinning.
This pulley is constructed from sturdy plastic with a metal bearing and measures 1-7/8" L x 3/4" W x 1-7/8" H. The kit includes the greased pulley wheel, washer, and tri-ring retaining clip — everything needed for a complete replacement. It mounts directly to the existing idler arm on compatible models. Note: this is the pulley wheel only, not the full idler arm assembly. On some newer Whirlpool models, the complete W10837240 idler pulley arm assembly may be required instead.
Quick Answer
The XPARTCO 279640 Dryer Idler Pulley fixes Whirlpool-family dryers that are squealing, squeaking, clunking, or have a drum that won't spin due to improper belt tension. Plastic body with metal bearing. 1-7/8" L x 3/4" W x 1-7/8" H. Kit includes pulley, washer, and tri-ring clip. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Crosley, Inglis, and Admiral dryers. Pulley only — not the full arm assembly.
Common Problems This Part Fixes
Loud squealing or squeaking noise when dryer is running
Clunking or thumping sound during the drying cycle
Dryer drum not spinning — belt slips or loses tension when pulley bearing fails
Belt repeatedly slipping off due to improper tension
Dryer drum spinning intermittently and stopping while the motor continues to run
Excessive vibration or shaking during the drying cycle
Visible wear, cracking, flat spots, or a pulley wheel that no longer spins freely on its shaft
Replaces Part Numbers
This idler pulley directly replaces the following OEM and cross-reference part numbers:
279640, 279640VP, 2958, 3388672, 697692, TJ279640, W10468057, AH334244, EA334244, ER279640, AWP39098, PD00002356, EAP334244, AP3094197, PS334244.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This idler pulley is compatible with select dryers from the following brands:
Whirlpool dryers (gas and electric)
Kenmore / Sears dryers (select Whirlpool-built models)
Maytag dryers (gas and electric)
KitchenAid dryers
Amana dryers
Crosley dryers
Inglis dryers
Admiral dryers
Important: The 279640 is a pulley wheel only — it mounts to the existing idler arm on compatible models. Some newer Whirlpool-family dryers (particularly models with the lint screen inside the door) require the complete W10837240 idler pulley arm and bracket assembly instead. If your model calls for W10837240, order that part rather than the 279640 pulley alone.
Key Features
Maintains correct tension on the drive belt for smooth, quiet drum rotation every cycle
Plastic body with metal bearing — durable construction resists wear and heat damage
Dimensions: 1-7/8" L x 3/4" W x 1-7/8" H — direct replacement for the original 279640
Kit includes greased pulley wheel, washer, and tri-ring retaining clip — ready to install
Pulley comes pre-greased — no additional lubrication required
Mounts directly to existing idler arm on compatible Whirlpool-family models
Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Crosley, Inglis, and Admiral dryers
Aftermarket replacement built to OEM-equivalent quality standards
Often replaced together with the drum belt (341241 or 661570V) for a complete drum drive repair
DIY-friendly repair — installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
279640
Part Type
Dryer Idler Pulley Wheel (Belt Tension Pulley)
Condition
Aftermarket Replacement
Application
Gas and Electric Dryers
Dimensions
1-7/8" L x 3/4" W x 1-7/8" H
Material
Plastic body / Metal bearing
Color
White
Lubrication
no additional lubrication required
Includes
Pulley wheel, washer, and tri-ring retaining clip
Note
Pulley wheel only — not the full arm assembly (see W10837240 for arm assembly)
Compatible Brands
Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Crosley, Inglis, Admiral
Often Replaced With
341241 or 661570V Drum Belt
Installation Notes
⚠️ Unplug Dryer Before Starting Unplug the dryer from the power outlet (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen and unscrew the Phillips screws inside the lint screen housing. Use a putty knife to release the top panel clips and lift the top panel. Remove the front panel to access the drum and drive components. Release belt tension from the idler pulley, then lift the drum and slide the belt off. Remove the tri-ring retaining clip from the idler arm shaft using needle-nose pliers, then slide the old pulley wheel off the shaft. Slide the new 279640 pulley wheel onto the idler arm shaft, reinstall the washer, and press the new tri-ring clip onto the shaft to secure the pulley. Re-route the drum belt around the new pulley and motor pulley, reinstall the drum, and reassemble the dryer. Run a test cycle to verify quiet operation. Tip: While the dryer is open, inspect the drum belt for wear and replace if needed. Tools needed: Phillips screwdriver, 1/4" nut driver, putty knife, small flat-head screwdriver, needle-nose pliers.
Frequently Asked Questions
What is the difference between the 279640 pulley and the W10837240 idler assembly?
The 279640 is just the pulley wheel — it replaces only the wheel on the existing idler arm and is used on older Whirlpool-family dryer models. The W10837240 is a complete idler arm and bracket assembly used on newer Whirlpool-family models (particularly those with the lint screen inside the door). If your dryer originally used the 279640, order this part. If your parts diagram calls for W10837240, order that assembly instead — the 279640 pulley alone will not fit the newer arm design.
What does the idler pulley do?
The idler pulley is a spring-tensioned wheel mounted on the idler arm inside the dryer. It presses against the drive belt to keep the correct amount of tension on the belt as it wraps around the drum. Without proper tension, the belt slips, the drum spins unevenly, or the drum stops spinning entirely. A worn pulley bearing also causes squealing, squeaking, or clunking noises during operation.
Should I replace the drum belt at the same time?
Yes — since the dryer is already disassembled, this is the ideal time to inspect and replace the drum belt (341241 or 661570V depending on your model). The belt and idler pulley wear at similar rates, and a worn belt on a new pulley significantly shortens the life of the new part. Replacing both together in a single repair also saves you from having to disassemble the dryer again shortly after.
Why is my dryer squealing?
A high-pitched squeal when the dryer starts or runs is one of the most common signs of a worn idler pulley bearing. As the bearing wears, it creates friction and noise against the shaft. The squeal typically gets louder over time and may eventually turn into a grinding or clunking sound as the bearing fails further. Replacing the idler pulley is usually the fix in these cases, and is much less expensive than a service call.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from durable plastic with a metal bearing to match the dimensions and performance of the original 279640 idler pulley.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPWE12X83 Dryer Idler Pulley
Replaces Part Numbers: WE12X83, WE12M0008, WE12M08, WE12M8, WE12X0080, WE12X0083, WE12X0092, WE12X80, WE12X92, AH265721, EA265721, AP2043227, PS265721.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
