Search results for "refrigerator control board"

ERP DA31-00020E Refrigerator Evaporator Motor Replaces Part Numbers: DA31-00020E, 2030081, DA31-00020E-, AP4136543, PS4138293.    This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

ERP WR60X203 Refrigerator Evaporator Fan Motor 120V, 60Hz, .21A, 3000RPM. 1-1/2" shaft. Has 2 (1/4") and 1 (3/16") terminals.   Replaces Part Numbers: WR60X203, 305540, AH304745, AP2071899, EA304745, PS304745, WR60X0191, WR60X0203, WR60X191   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO XP311 Dryer Thermostat Kit for LG The XPARTCO XP311 is an aftermarket replacement 3-piece thermostat kit for LG electric dryers, bundling the thermal fuse, thermistor, and high-limit thermostat that work together to regulate and protect the dryer's heating system. These three components monitor heat continuously during normal operation and step in at different thresholds if something goes wrong, which is why they're commonly replaced as a set — a single overheating event or a slow age-related drift in one part can put stress on the others, and buying them together also saves a second teardown if one of the remaining parts fails soon after. This kit includes: the 6931EL3003D thermal fuse, a one-time safety device that permanently cuts power to the dryer if internal temperatures climb dangerously high; the 6323EL2001B thermistor, a temperature sensor assembly with wire harness that continuously reports drum temperature to the control board so it can regulate heat output during the cycle; and the 6931EL3001E high-limit thermostat, which automatically shuts off the heating element if the dryer's temperature exceeds safe operating limits, without needing to be replaced like the thermal fuse does. Symptoms of failure in this circuit include incomplete drying, insufficient heating time, overheating that damages clothing, and the dryer shutting down prematurely or failing to start at all. It directly replaces AP4440975, 1268366, 6931EL3003E, AH3530485, EA3530485, PS3530485 (thermal fuse); AP4441539, 1268206, 6323EL2001H, AH3529026, EA3529026, PS3529026 (thermistor); and AP4440977, 1268363, 6931EL3001B, 6931EL3001C, AH3530481, EA3530481, PS3530481, 6931EL3001F (high-limit thermostat). Quick Answer The XPARTCO XP311 Dryer Thermostat Kit fixes LG (and select Kenmore) electric dryers with incomplete drying, insufficient heat, overheating that damages clothes, or a dryer that shuts down prematurely or won't start. 3-piece kit: thermal fuse (6931EL3003D), thermistor (6323EL2001B), and high-limit thermostat (6931EL3001E). Replaces 6323EL2001B, 6931EL3001E, 6931EL3003D, and their full cross-reference sets listed below. These three parts share the same circuit and commonly fail together — replacing all three at once is standard practice when one has failed. What's In The Kit Component Part Number Function Thermal Fuse 6931EL3003D One-time safety device — permanently cuts power if the dryer overheats. Cannot be reset once blown. Thermistor 6323EL2001B Continuously senses drum temperature and reports it to the control board to regulate heat output. High-Limit Thermostat 6931EL3001E Automatically shuts off the heating element if temperature exceeds safe limits. Resets automatically, unlike the thermal fuse. Common Problems This Kit Fixes Dryer runs but clothes come out only partially dry Insufficient heating time or reduced heat output Overheating that scorches or damages clothing Dryer shuts down prematurely mid-cycle Dryer won't start at all Inconsistent drying results from cycle to cycle Dryer that recently blew a thermal fuse and needs the related components checked Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermostat kit directly replaces the following OEM and cross-reference part numbers: 6931EL3003D, 1268366, AH3530485, EA3530485, PD00001818, EAP3530485, AP4440975, PS3530485, 6323EL2001B, 1268206, 6323EL2001H, AH3529026, PD00001821, EAP3529026, EA3529026, AP4441539, PS3529026, 6931EL3001E, 1268363, 6931EL3001C, PD00023869, EAP3530481, AH3530481, EA3530481, AP4440977, PS3530481. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This kit is compatible with select LG electric dryers, and also fits select Kenmore dryers built on the LG platform, including model numbers such as: CDE3379WN DLE0332W, DLE0442G, DLE0442W, DLE0442W01 DLE1310W, DLE2101W, DLE2140W, DLE2240W DLE2512W, DLE2514W, DLE2515S, DLE2516W, DLE2522W, DLE2524W, DLE2532W DLE3733D, DLE3733S, DLE5955W Note: This kit is for LG electric dryers. Different resistance values, dimensions, and mounting methods apply across brands and models, so always verify your full model number before ordering rather than relying on physical resemblance alone. Contact our support team with your model number if you're unsure. Key Features Complete 3-piece kit — thermal fuse, thermistor, and high-limit thermostat in one purchase Addresses the full temperature-regulation and safety circuit at once, rather than piecemeal Resolves "incomplete drying," "insufficient heat," "overheating," and "premature shutdown" symptoms Thermistor ships with its wire harness included No special tools required for installation Direct drop-in replacement for all three original components Replaces the full cross-reference set for 6931EL3003D, 6323EL2001B, and 6931EL3001E listed above Compatible with LG and select Kenmore electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Kit Part Number XP311 Kit Contents 1x Thermal Fuse (6931EL3003D), 1x Thermistor (6323EL2001B), 1x High-Limit Thermostat (6931EL3001E) Condition Aftermarket Replacement Application LG Electric Dryers Thermal Fuse Type One-time use, non-resettable High-Limit Thermostat Type Automatically resetting Thermistor Includes wire harness Repair Difficulty Easy to Moderate — no special tools required Compatible Brands LG, select Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Test Before Assuming All Three Have Failed Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel or the front, depending on your model — these components are commonly mounted on or near the blower housing and heater duct assembly. Photograph the wiring connections before disconnecting anything, since the thermal fuse, thermistor, and high-limit thermostat can look similar and are easy to swap positions by mistake. Before installing the full kit, it's reasonable to test each old component with a multimeter to confirm which have actually failed — the thermal fuse and high-limit thermostat can each be checked for continuity, though replacing all three together is still standard practice given how this circuit tends to fail. Remove each old component from its mounting position, noting orientation, and disconnect its wiring. Install each new component from the kit in the same position and orientation as the part it replaces, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal heating, consistent drying, and no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), multimeter (recommended), work gloves. Frequently Asked Questions Do I really need to replace all three parts, or can I just replace the one that failed? You can test each component individually with a multimeter and replace only the ones that fail, but there's a good reason these are commonly sold and replaced together: they share the same heating circuit and tend to age or fail around the same time, especially if an overheating event caused the original failure. Replacing all three at once avoids a second teardown if one of the remaining original parts fails again soon after. What's the difference between the thermal fuse and the high-limit thermostat? They sound similar. Both protect against overheating, but they behave very differently. The high-limit thermostat is the first line of defense — it shuts off the heating element automatically if temperature climbs too high, then resets itself once things cool down, letting the dryer resume normal operation. The thermal fuse is the backup: if temperatures climb high enough that the thermostat alone doesn't prevent a dangerous overheat, the fuse permanently opens the circuit and cuts all power. Unlike the thermostat, the fuse cannot reset itself and must be physically replaced once it blows. What does the thermistor actually do, and why does it matter if it's a sensor rather than a switch? The thermistor doesn't switch anything on or off directly — it's a variable resistor whose resistance changes with temperature, and the control board reads that resistance continuously to know exactly how hot the drum is running. That ongoing feedback is what lets the control board fine-tune heat output throughout the cycle rather than just running hot or cold. A failing thermistor can cause the control to misjudge temperature, leading to insufficient heat, inconsistent drying, or the control cutting the cycle short. My dryer blew a thermal fuse. Should I get this whole kit instead of just the fuse? It's worth considering, especially since a blown thermal fuse usually means the dryer actually overheated at some point — and that same overheating event can stress the thermistor and high-limit thermostat even if they haven't failed outright yet. Also worth checking regardless of which parts you replace: restricted exhaust venting is the most common root cause of dryer overheating, so inspect and clean the vent ducting when you do this repair, or the new parts may face the same stress that damaged the originals. Is this an OEM or aftermarket kit? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine LG OEM kit, but each component is manufactured to match the electrical specifications, resistance values, and mounting configuration of the original 6931EL3003D thermal fuse, 6323EL2001B thermistor, and 6931EL3001E high-limit thermostat used in compatible LG electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

316233903 Oven Genuine Temperature Sensor Replaces Part Numbers:  316233903, 316217008, 316233902, 316233900, AP5998652, PS11731754. Description: This Oven Temperature Sensor is a Genuine part for select Frigidaire, Kenmore oven models. It monitors and regulates the oven's temperature by sending accurate temperature readings to the control board. This ensures that the oven maintains the desired cooking temperature throughout the baking or roasting process.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO 8577274 Dryer Thermistor - Compatible with Whirlpool, Kenmore, Maytag Product Description Ensure optimal drying performance with the XPARTCO 8577274 Dryer Thermistor. This replacement temperature-sensing resistor is designed as a replacement for select Whirlpool, Kenmore, Maytag, and other compatible dryers, offering a cost-effective alternative to the original. It monitors air temperature changes during the drying cycle, providing feedback to the control board to regulate heat levels, preventing overheating and ensuring efficient drying. This part addresses issues like prolonged or shortened drying times, inaccurate temperature readings, or error codes, often caused by a faulty thermistor. Note: Includes (1) thermistor (mounting hardware not included). Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: WP8577274, 8577274, 1181075, 3390292, 3406294, 3976615, 772546, ER8577274, WP8577274VP, PD00002401, EAP11746740, AP6013514, PS11746740. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: 3LCED9100WQ0, 7MGGW9200MW3, 7MWGD8300SW1, 7MWGD8500SR1, WED6200SW1, WED8000DW3, WED8300SW0, MEDB880BW0 Kenmore: 110.60884990, 110.6007299, 110.6093699, 110.7095299 Maytag: 7MMGDB850WL0, MVWC565FW0 KitchenAid, Amana, Inglis, Crosley: Various models (verify with model number) Verify your model number or contact our support team for assistance. Key Features: Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, and Crosley dryers. Specifications: High-quality thermistor, approximately 11K Ohms at 70°F (21°C), located on blower housing. Reliable Performance: Monitors drum air temperature to prevent overheating and ensure efficient drying. Easy Installation: Requires 1/4-inch nut driver, small flathead screwdriver, and pliers; typically installed in 15–30 minutes. Effective Fixes: Resolves prolonged or shortened drying times, inaccurate temperature readings, or error codes. Product Specification Part Number: XPARTCO 8577274 Component Type: Dryer thermistor Material: Plastic and metal Electrical Specs: Approximately 11K Ohms at 70°F (21°C), varies with temperature Compliance: Prop 65 warning for California. Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running efficiently today! Add to cart now for a reliable fix!

Read more less

W10280608 Freezer Bracket  Bracket - Left Side   Replaces Part Numbers: WPW10280608, W10280608, W10187668, 12812301, 12812303, 4443902, 67004014, 8171234, AP6018544, PS11751846.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

131436700 Washer Genuine Control Timer   Replaces Part Numbers:  131436700, OEM8427502, AP2106875, 407393, AH417799, EA417799, PS417799.  

Read more less

Genuine OEM EAU65058315 Refrigerator Evaporator Fan Motor The Genuine OEM LG EAU65058315 is a DC evaporator fan motor assembly for select LG and Kenmore refrigerators. The evaporator fan motor circulates cold air through the refrigerator, helping to keep temperatures consistent and prevent frost buildup. When it wears out or fails, the refrigerator may run too warm or too cold, build up frost, or make unusual noise. This is the original LG part, not an aftermarket equivalent. It is the evaporator fan, not the condenser fan near the compressor. Check your model number before ordering. Quick Answer The Genuine OEM EAU65058315 Evaporator Fan Motor replaces the evaporator fan motor on a compatible LG or Kenmore refrigerator when it has failed. Classic symptoms: the refrigerator or freezer is too warm, frost builds up, or the fan makes unusual noise. Other parts can cause the same symptoms, so confirm the fan is the problem first. Common Problems This Part Fixes Refrigerator or freezer too warm or too cold Frost buildup Unusual noises from the fan area Moisture or water leaking Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This evaporator fan motor is listed under the following part number: EAU65058315 replaces EAU63103209, ODM-056F-15, ALG54104, AP6247423, EAP12115088, PD00081425, PS12115088, PS17308826, AP7211789 LG uses many similar fan motor numbers for different models. If your old motor shows a different number, contact our support team and we'll check whether it matches. Compatibility This evaporator fan motor is listed for LG, Kenmore and Kenmore Elite bottom-mount refrigerators, including these examples: LG LFX25974SW, LFCS22520S, LFDS22520S Kenmore 79570339411, 79579412811, 79579412810 Kenmore Elite 79579049314, 79579044313 Note: The models above are a sample, not a full list. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM LG part, not an aftermarket equivalent DC motor assembly Circulates cold air through the refrigerator Helps keep temperatures consistent and prevent frost buildup Product Specifications Part Number EAU65058315 OEM Part Number EAU65058315 Part Type Refrigerator Evaporator Fan Motor Condition Genuine OEM Manufacturer LG Motor Type DC Application Select LG, Kenmore & Kenmore Elite Refrigerators Installation Notes ⚠️ Unplug Power Before Installing Unplug the refrigerator and move perishable food to a cooler before you begin. Wear work gloves. Follow your model's service guide to reach the evaporator fan, note how the wiring connects, and swap the motor. Reconnect the wiring, restore power, and check that the fan runs quietly. Frequently Asked Questions My refrigerator is running warm. Is this the part I need? It can be, if the evaporator fan has failed. Other parts can cause the same symptoms, so check that the fan isn't blocked by frost and that the fan itself isn't spinning before replacing it. Is this the evaporator fan or the condenser fan? This is the evaporator fan motor, which circulates cold air through the refrigerator. The condenser fan motor is a different part, located near the compressor. Is this an OEM or aftermarket part? This is a genuine OEM part from LG, not an aftermarket equivalent. Will this fit my refrigerator? It is listed for select LG, Kenmore and Kenmore Elite bottom-mount models, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

17438200000404 Genuine OEM Midea Dryer Temperature Sensor (Thermistor) The 17438200000404 is a Genuine OEM Midea replacement dryer temperature sensor (thermistor) compatible with an extensive range of Midea, Criterion, and Insignia electric and gas dryers. This NTC (negative temperature coefficient) thermistor continuously monitors air temperature inside the dryer and sends resistance-based readings to the control board, which uses this data to regulate heating element cycling, prevent overheating, and maintain consistent drying temperatures throughout the cycle. As the thermistor heats up, its electrical resistance decreases in a predictable way, allowing the control board to calculate the exact temperature in real time. When this sensor fails — whether shorted, open, or providing drifted/inaccurate readings — the dryer may overheat, may not heat at all, may dry clothes unevenly, may take much longer than normal to complete a cycle, or may trigger a not-heating fault on models with digital displays. As a Genuine OEM part manufactured by Midea to factory specifications, the 17438200000404 directly replaces WF-123X2060 (an alternate catalog cross-reference used by some suppliers, including for compatible Maytag-branded Midea-built units). Installs in 20–30 minutes with basic hand tools. Quick Answer The 17438200000404 Genuine OEM Midea Dryer Temperature Sensor (Thermistor) fixes Midea, Criterion, and Insignia dryers that are overheating, not heating, drying unevenly, or taking too long to dry. NTC thermistor — resistance drops as temperature rises; ~10,000–12,000 ohms at room temperature (70°F). Genuine OEM. Replaces WF-123X2060. Compatible with Midea MLE41N1AWW, MLE45N1AWW/BWW, MLE45N3BMG/BWW, MLE52N3AWW, MLE52S7AGS/AWW, MLG45N1AWW/BWW, MLG45N3BMG/BWW, MLG52S7AGS/AWW, Criterion CDE41N1AW/CDG41N1AW, and a wide range of Insignia models. Common Problems This Part Fixes Dryer overheating — thermistor not accurately reporting rising temperature to the control board Dryer not heating at all — thermistor circuit open or shorted Dryer drying clothes unevenly — inconsistent temperature regulation during the cycle Dryer taking much longer than normal to complete a cycle Not-heating fault code displayed on models with digital control panels Multimeter test shows 0 ohms (shorted) or infinite resistance (open) instead of the expected NTC reading Dryer cycling heat on and off erratically Replaces Part Numbers This temperature sensor directly replaces the following OEM and cross-reference part numbers: 17438200000404, WF-123X2060, AP7157538, PS18188581 Contact our support team with your model number if you need confirmation before ordering. Compatibility This temperature sensor is compatible with an extensive range of Midea, Criterion, and Insignia dryers, including: Midea electric dryers — MLE41N1AWW, MLE41N1AWWC, MLE45N1AWW, MLE45N1BWW, MLE45N1BWWC, MLE45N3BMG, MLE45N3BWW, MLE52N3AWW, MLE52S7AGS, MLE52S7AWW Midea gas dryers — MLG45N1AWW, MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AGS, MLG52S7AWW Midea — CLADE67W, MDD160A2301E1305, MDD160VG012F0110EUS13 Criterion — CDE41N1AW (electric), CDG41N1AW (gas) Insignia electric dryers — NSDRE67WH8A, NSDRE67WH8AC, NSFDRE67WH8A, NSFDRE67WH8AC, NSFDRE77WH8B, NSFDRE77WH8BC, NSTDRE67W1, NSTDRE75W1 Insignia gas dryers — NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1 Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance NTC (negative temperature coefficient) thermistor — resistance decreases predictably as temperature rises, allowing precise temperature monitoring Sends real-time temperature data to the control board to regulate heating element cycling and prevent overheating Approximately 10,000–12,000 ohms of resistance at room temperature (around 70°F) when functioning correctly Compatible across both electric and gas Midea-platform dryers, including Criterion and Insignia house-brand models Replaces WF-123X2060 Installs in 20–30 minutes with basic hand tools Product Specifications Part Number 17438200000404 Part Type Dryer Temperature Sensor (NTC Thermistor) Condition Genuine OEM Application Electric and Gas Dryers (Midea platform) Sensor Type NTC (Negative Temperature Coefficient) Resistance at Room Temp Approximately 10,000 – 12,000 ohms (~70°F) Location Blower housing/exhaust duct or drum cavity, depending on model Compatible Brands Midea, Criterion, Insignia Installation Notes ⚠️ Unplug Dryer Before Starting (Shut Off Gas First on Gas Models) Disconnect power before beginning (and shut off the gas supply first if you have a gas dryer model). Midea dryers typically have 2–3 temperature sensors: an exhaust thermistor on the blower housing or exhaust duct, a drum thermistor inside the drum cavity, and on heat pump models, an evaporator thermistor — confirm which sensor location matches your symptom and part diagram before starting. Access the sensors by removing the back panel on vented models, or the side/bottom panels on heat pump models. Photograph the connector position before disconnecting. Unplug the old sensor's connector and inspect it for corrosion or heat discoloration on the wires — discoloration indicates prior overheating in that area. Remove the mounting clip or screw securing the old sensor and pull it free. Install the new 17438200000404 sensor in the same position, reseat the connector firmly, and secure the mounting hardware. Reassemble the panel, restore power, and run a test heat cycle to confirm normal temperature regulation. Tools needed: Phillips screwdriver, multimeter (for testing). Frequently Asked Questions How do I test if the temperature sensor (thermistor) has failed? Unplug the dryer, disconnect the sensor's connector, and set your multimeter to resistance mode. At room temperature (around 70°F), a working NTC thermistor should read approximately 10,000 to 12,000 ohms. If the sensor reads 0 ohms, it has shorted internally. If it reads infinite resistance (open circuit, often shown as "OL" on the multimeter), the sensor has failed open. Either reading confirms the sensor needs replacement. If you have multiple sensors testing bad at the same time, check the shared ground wire — a broken ground connection can cause all sensors on that circuit to read as open even if the individual sensors are fine. My Midea dryer has more than one temperature sensor — how do I know which one to replace? Midea dryers typically use 2–3 temperature sensors depending on the model: an exhaust thermistor mounted on the blower housing or exhaust duct, a drum thermistor inside the drum cavity, and — on heat pump/ventless models — an evaporator thermistor in the refrigerant circuit area. The 17438200000404 is used across this Midea/Criterion/Insignia platform, but confirming the exact mounting location for your specific symptom (e.g., overheating vs. uneven drying) and model number before ordering will help ensure you're replacing the correct sensor. What is the difference between 17438200000404 and WF-123X2060? These are the same temperature sensor. WF-123X2060 is an alternate catalog cross-reference number used by some parts suppliers for the identical Midea-manufactured thermistor — it appears in listings for compatible Maytag-branded Midea-built units as well as the standard Midea, Criterion, and Insignia models. If your dryer's parts diagram shows either number, the 17438200000404 is the correct part. Does this sensor fit my Insignia or Criterion dryer? Yes — Insignia (Best Buy) and Criterion (Sears/Kmart) are house brands whose dryers in this size and configuration are manufactured by Midea and use the same internal components, including this temperature sensor. Confirmed compatible models include Insignia NSDRE67WH8A, NSFDRE67WH8A, NSFDRE77WH8B, NSTDRE67W1, NSTDRE75W1 (electric) and NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1 (gas), as well as Criterion CDE41N1AW (electric) and CDG41N1AW (gas). Always verify your specific model number before ordering. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same NTC thermistor temperature sensor installed in compatible Midea, Criterion, and Insignia dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

316490000 Oven Genuine OEM Temperature Sensor Product Overview The 316490000 Oven Genuine OEM Temperature Sensor is designed to accurately monitor oven temperature and ensure proper heating performance.  This Oven Sensor Assembly is a Genuine OEM part for select Frigidaire oven models, designed to accurately measure the oven's internal temperature and communicate it to the control board. This ensures that the oven maintains the desired temperature setting during baking or roasting, providing consistent cooking results.  Quick Answer If your oven is overheating, not heating properly, or showing incorrect temperature readings, the 316490000 temperature sensor may be faulty. Replacing it restores accurate temperature control and consistent cooking results. Replaces Part Numbers Replaces OEM part number: 316490000, 316490003, 1197392, 316490002, 612058426864, 7316490000, AH1528542, EAP1528542, AFR16190, PD00000483, OEM15854618, AP3963654, PS1528542. Compatibility This oven temperature sensor is compatible with select Frigidaire, Electrolux, Kenmore, and other compatible ranges and ovens. Frigidaire Ranges & Ovens Electrolux Appliances Kenmore Ranges Always verify your appliance model number before ordering. Common Problems This Part Fixes Oven overheating or under-heating Inaccurate temperature readings Uneven cooking results Error codes related to temperature sensor Key Features Genuine OEM temperature sensor Accurate temperature monitoring Reliable and durable construction Restores proper oven performance Product Specifications Part Number: 316490000 Part Type: Oven Temperature Sensor Brand: OEM Condition: New OEM / Aftermarket: Genuine OEM Application: Ovens & Ranges Troubleshooting Guide Oven too hot or too cold → Faulty temperature sensor Food overcooking or under-cooking → Incorrect temperature readings Error codes displayed → Sensor failure likely When Should You Replace This Sensor? Replace this sensor if your oven temperature is inconsistent, inaccurate, or if error codes indicate a sensor issue. Installation Notes ⚠️ Disconnect power before installation. Remove mounting screws, disconnect wiring, and install the new sensor securely. Refer to your appliance manual if needed. Related Parts Oven Control Board Heating Element Thermostat Components Frequently Asked Questions Will this sensor fit my oven?This sensor fits many Frigidaire and compatible models. Always verify your model number. What does an oven temperature sensor do?It monitors oven temperature and sends signals to maintain accurate heat levels. What are signs of a bad sensor?Inconsistent temperatures, error codes, or improper cooking results. Is this OEM?Yes, this is a genuine OEM temperature sensor. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Genuine OEM Parts Compatibility Support  

Read more less

WB03X43926 Genuine OEM GE Range Surface Burner Control Knob Set The WB03X43926 is a genuine GE OEM surface burner knob kit, including 5 stainless steel knobs for GE, Hotpoint, Haier, Monogram, and Café ranges. These are the knobs you turn to light and adjust each surface burner — each one fits onto a control shaft behind the panel, and its position controls the heat setting for that burner. Since this kit includes a full set of five, it's designed for replacing every burner knob on the range at once rather than mismatching a single new knob against several older, worn ones. Over years of use, the finish on plastic-coated or stainless-finished knobs can crack, peel, or start to bubble, and the knobs themselves can become loose or worn at the point where they grip the control shaft. A full-set replacement gives your range a uniform, refreshed look while also resolving any individual knobs that have become difficult to turn or read. Weighing approximately 2.64 oz total, this kit requires no tools to install — each knob simply pulls straight off its post and the new one presses straight back on. It directly replaces AP7187858, WB03K10305, WB03K10303, WB03K10208, WB03K10221, and WB03K10294. Quick Answer The WB03X43926 Genuine OEM GE Range Surface Burner Control Knob Set fixes GE, Hotpoint, Haier, Monogram, and Café ranges with burner knobs that are cracked, peeling, bubbling, loose, or simply worn-looking after years of use. Set of 5 stainless steel knobs. Replaces AP7187858, WB03K10305, WB03K10303, WB03K10208, WB03K10221, WB03K10294. No tools required — each knob pulls straight off and the new one presses straight on. Common Problems This Part Fixes Burner knobs with cracked, peeling, or bubbling finish Knobs that feel loose or wobbly on the control shaft Knobs that are hard to read due to worn or faded markings Mismatched or inconsistent-looking knobs across the range from replacing them one at a time Knobs that have become difficult to turn smoothly General wear after many years of daily cooking use Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This range surface burner knob set directly replaces the following OEM and cross-reference part numbers: WB03X43926, WB03K10303, WB03K10305, WB03K10208, WB03K10221, WB03K10294, AP7187858, OEM21563583, AGE21567, PD00074146 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This burner knob set is compatible with select GE ranges, and also fits select Hotpoint, Haier, Monogram, and Café ranges built on the GE platform. Note: This is the stainless steel finish knob set. GE also sells a visually different black plastic knob (WB03T10236) for other range models — the two are not interchangeable, so confirm your original knob's finish and shaft style before ordering. Always verify your full model number before ordering, since GE uses several different knob designs across its range lineup. Contact our support team with your model number if you're unsure which knob set fits your range. Key Features Genuine GE OEM part — factory-specified fit and finish Complete set of 5 stainless steel surface burner knobs for a uniform look across the range Resolves "cracked or peeling finish," "loose knob," and "worn markings" symptoms No tools required — pulls straight off the post, presses straight back on Compatible with the same control shaft used across a range of GE-platform ranges Replaces AP7187858, WB03K10305, WB03K10303, WB03K10208, WB03K10221, and WB03K10294 Compatible with GE, Hotpoint, Haier, Monogram, and Café ranges Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WB03X43926 Part Type Range Surface Burner Control Knob Set Condition Genuine OEM Brand GE Kit Contents 5 surface burner knobs Finish Stainless steel Weight Approx. 2.64 oz. (full set) Mount Style Push-fit onto control shaft Repair Difficulty Very Easy — no tools required Quantity 1 set (5 knobs) Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Unplug Range Or Shut Off Breaker Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Remove each old knob by pulling it straight off its post — on most models this requires no tools, just firm, even pressure. Align each new knob from the WB03X43926 set with its corresponding control panel position and indicator arrow, then press it firmly onto the post until it seats flush. Repeat for all five burner positions. There's no need to remove the knobs for normal baking, broiling, or self-clean use once installed. Restore power and test that each knob turns smoothly through its full range, with the markings lining up correctly against the indicator arrow at each setting. Tools needed: none. Frequently Asked Questions My knobs' finish is bubbling after many years. Is this the right fix? Yes, this is a common wear pattern on older knobs — one customer described replacing 14-year-old knobs whose coating had started to bubble, and found the swap simple enough to do entirely by hand with no tools. If your knobs are showing this kind of surface wear, a full set replacement gives your range a consistent, refreshed look across all burners. Do I need to remove these knobs before running a self-clean cycle? No — these knobs are designed to be left in place during normal oven use, including self-clean cycles. One customer specifically noted using the self-clean feature without removing the knobs and had no issues. Can I buy just one replacement knob instead of the full set of 5? This particular listing is sold as a complete 5-knob set rather than individually. If only one knob has failed, you may still prefer the full set for a matching, uniform appearance across the range, especially if the remaining original knobs are also showing age. Contact our support team if you're looking for a single replacement knob instead. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original stainless steel finish, shaft fit, and marking layout of the surface burner knobs originally installed on your range. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WB24X10146 Microwave Door Switch The XPARTCO WB24X10146 is an aftermarket replacement micro switch (also called a door interlock switch) compatible with a wide range of GE, Hotpoint, RCA, Kenmore, and Sears over-the-range and countertop microwaves. This is a "stand on" style normally-open (NO) interlock switch, identified by the internal designation KW3A-NO, that mounts near the door latch and only closes its circuit when the door is fully shut and latched. The control board reads this switch as part of a multi-switch safety interlock chain that confirms the door is secure before allowing the magnetron to energize. When this switch fails, the microwave commonly won't start at all, trips a door-related error code, or in rare cases can allow the unit to run with the door not fully secured — which is a safety-relevant fault, not just a convenience one. It directly replaces WB24X10146, WB24X28941, MW-7100-33, AGE22794, AH1019163, AP3866977, 1166990, EA1019163, EAP1019163, PD00039881, PS1019163. Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO WB24X10146 Microwave Door Switch fixes GE, Hotpoint, RCA, and Kenmore/Sears microwaves that won't start, display a door-related error code, or have a door that doesn't reliably confirm as closed. Normally-open (NO) "stand on" interlock switch, rated 250VAC / 16A, with 0.187" (4.7mm) quick-connect terminals. Replaces WB24X10146, WB24X28941, MW-7100-33, AGE22794, AH1019163, AP3866977, 1166990, EA1019163, EAP1019163, PD00039881, PS1019163. Classic symptom: turntable light and display work, but pressing Start does nothing. Common Problems This Part Fixes Microwave won't start when Start is pressed, even though the display and light work Door-related error code or fault light on the display Microwave randomly shuts off mid-cycle Door feels like it isn't latching or registering as closed Clicking sound from the door area with no response from the microwave Intermittent operation that seems tied to how hard the door is closed ⚠ Safety-Relevant Component Door interlock switches are safety components that prevent the magnetron from energizing unless the door is fully closed and latched. Never bypass, jumper, or defeat a microwave door switch to "get it working" — doing so can allow microwave energy to leak while the door is open, which is a genuine radiation safety hazard. Always disconnect power before servicing, and replace all interlock switches in the chain if more than one shows signs of wear. Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This microwave door switch directly replaces the following OEM and cross-reference part numbers: WB24X10146, WB24X28941, MW-7100-33, AGE22794, AH1019163, AP3866977, 1166990, EA1019163, EAP1019163, PD00039881, PS1019163 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is compatible with a wide range of GE-built microwaves across the following brands: GE over-the-range and countertop microwaves (JVM, PVM, and CEB series, including JEM3072DH1BB, JEM3072SH1SS, JNM3161DF2BB, and CCWK15C1W1DS/SS) Hotpoint microwaves (GE-built models) RCA microwaves (GE-built models) Kenmore and Sears microwaves (select GE-built models) Note: Do not confuse this with the similarly styled EXP499/EXP497 microwave door switches, which also use 4.7mm terminals but are not the same switch. WB24X10146 is a "stand on" style switch specific to GE's own interlock design — always match by part number, not terminal size alone. Always verify your appliance model number before ordering. Key Features Normally-open (NO) "stand on" door interlock switch, internal designation KW3A-NO Resolves "won't start," "door error code," and "shuts off mid-cycle" symptoms caused by interlock switch failure Rated 250VAC / 16A for reliable switching under microwave load 0.187" (4.7mm) quick-connect terminals for a secure wire connection Direct-fit mounting to match the original interlock bracket Replaces WB24X10146, WB24X28941, MW-7100-33, AGE22794, AH1019163, AP3866977, 1166990, EA1019163, EAP1019163, PD00039881, PS1019163 Compatible with GE, Hotpoint, RCA, Kenmore, and Sears microwaves across dozens of models Aftermarket replacement built to OEM-equivalent quality and safety standards Product Specifications Part Number XPWB24X10146 OEM Part Number WB24X10146 Part Type Microwave Door Interlock Switch ("Stand On" / KW3A-NO) Condition Aftermarket Replacement Switch Type Normally Open (NO) Voltage Rating 250VAC Current Rating 16A Terminal Width 0.187" (4.7mm) Compatible Brands GE, Hotpoint, RCA, Kenmore, Sears Installation Notes ⚠️ Unplug Microwave Before Starting Disconnect power at the outlet, and for built-in/over-the-range units also switch off the dedicated circuit breaker — microwaves store high voltage in the capacitor even after unplugging. Remove the outer cabinet or control panel cover to access the door switch assembly near the latch mechanism. Photograph the wiring before disconnecting, since GE microwaves typically use two or three interlock switches wired in sequence and mixing up the connections can leave the unit unsafe to operate. Disconnect the quick-connect terminals from the old switch, noting which wire goes to which terminal. Remove the mounting screw(s) holding the switch to its bracket and remove the old switch. Install the new WB24X10146 in the same position and secure it with the mounting screw(s). Reconnect the terminals exactly as photographed. Reassemble the cabinet or panel, restore power, and test that the door registers correctly and the microwave starts normally. Tools needed: Phillips screwdriver, nut driver (for cabinet screws). Frequently Asked Questions My microwave's display and turntable light work, but it won't start — is this the part? This is a classic symptom of a failed door interlock switch. The control board needs a confirmed "door closed and latched" signal from all switches in the interlock chain before it will energize the magnetron. If that signal is missing from even one switch, most GE microwaves will power up normally but refuse to start a cook cycle. Confirm with a multimeter continuity test on the suspect switch before ordering, since GE microwaves usually use more than one interlock switch. Is this the same as the EXP499 or EXP497 microwave door switch? No — while all three use similar 4.7mm terminals, they are different switches used in different microwave platforms and are not interchangeable. WB24X10146 is GE's own "stand on" KW3A-NO design. Always match by part number rather than terminal size or general appearance. Is it safe to keep using the microwave if I suspect this switch is bad? We'd recommend not continuing to use it until it's repaired. Door interlock switches exist specifically to prevent microwave energy from leaking out while the door is open or not fully latched. If a switch is failing intermittently, the microwave may seem to work sometimes, but that's not a reason to keep using it — replace the switch before further use, and never attempt to bypass or jumper an interlock switch. How many interlock switches does my GE microwave have, and do I need to replace them all? Most GE microwaves use two or three interlock switches wired in sequence (often a primary switch, a secondary/monitor switch, and sometimes a door sensing switch). You typically only need to replace the specific switch that's testing bad, but if one has failed from age or wear, the others are often not far behind — some technicians replace the full set at once to avoid a repeat repair call. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less