Search results for "washer switch"

279769 Genuine OEM Whirlpool Dryer Thermostat Kit The 279769 is a genuine Whirlpool OEM thermal cut-off and high-limit thermostat kit for Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers. This kit bundles two components that guard against overheating at different thresholds: the 3390291 high-limit thermostat (rated L250-80F) monitors internal temperature and interrupts power at approximately 250°F to prevent overheating, then resets itself automatically once the dryer cools — no replacement needed after each trip. The 3977394 thermal cut-off fuse is the backup: rated at 352°F, it's a one-time safety device that permanently opens the circuit if temperatures climb high enough that the thermostat alone didn't prevent an overheat. These two parts are sold together and should be replaced together as a set, since they protect the same circuit and tend to be stressed by the same underlying problem. Whirlpool's own guidance is direct: when the thermal cut-off fails, it usually indicates a venting problem, and failing to correct that airflow issue will cause repetitive failures even with new parts installed. Symptoms include the dryer not heating, clothes coming out extremely hot, or the dryer not running at all. This kit is commonly used alongside heating element 4391960. It directly replaces 279548, 2796769, 279769VP, 2821, 2004, 3387812, 3389946, 3398671, 3977394, 695563, 80001, SET184, SET198, TJSET198, ET184, AP3094224, AH334278, EA334278, EAP334278, PD00002485, PS334278, WP3390291, AP6008306, 3390291, 696397, and PS11741441. Quick Answer The 279769 Genuine OEM Whirlpool Dryer Thermostat Kit fixes Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers with no heat, no power at all, or clothes coming out dangerously hot. Includes the 3390291 high-limit thermostat (250°F, auto-resetting) and the 3977394 thermal cut-off fuse (352°F, one-time). Replaces 279548, 2796769, 279769VP, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AP3094224, PS334278, WP3390291, AP6008306, 3390291, 696397, PS11741441. Always inspect and clean the exhaust venting when replacing this kit — a blown thermal fuse is a symptom of restricted airflow, and skipping the vent check leads to repeat failures. What's In The Kit Component Rating Function 3390291 High-Limit Thermostat L250-80F (~250°F) Interrupts power to prevent overheating, resets automatically once the dryer cools. 3977394 Thermal Cut-Off Fuse 352°F One-time backup safety device — permanently opens the circuit if temperature exceeds safe limits. Cannot reset. Common Problems This Kit Fixes Dryer won't start at all — no lights, no tumble, no response Dryer runs but produces no heat Clothes coming out extremely hot, hot enough to be uncomfortable to handle Dryer that stopped working suddenly after running unusually hot Repeated thermal cut-off failures on a dryer with a known venting issue Dryer that shuts off prematurely mid-cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermostat kit directly replaces the following OEM and cross-reference part numbers: 279769, 2004, 279548, 2796769, 279769VP, 2821, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AH334278, EA334278, AP3094224, OEM9282681, SET184, SET198E, AP334278, L250-80F, PS334278, AWP39149, PD00002485. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat kit is compatible with select Whirlpool electric dryers, and also fits select Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral dryers built on the Whirlpool platform, including model numbers such as: 7MWET4027HW0 WET3300XQ0 WET4027EW0, WET4027EW1 WET4027HW0, WET4027HW1, WET4027HW2 WETLV27FW0, WETLV27HW0, WETLV27HW1, WETLV27HW2, WETLV27HW3 YWET4027EW1, YWET4027HW0, YWET4027HW1, YWET4027HW2 Note: This kit was used on Whirlpool-built electric dryers primarily from 1985 to 1995. Always verify your full model number before ordering, since Whirlpool used several different thermostat and fuse designs across its dryer lineup over the years. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified thresholds for both components 2-piece kit: 3390291 high-limit thermostat (250°F, auto-resetting) and 3977394 thermal cut-off fuse (352°F, one-time) Resolves "no heat," "no power at all," and "clothes coming out extremely hot" symptoms Addresses two overheat-protection thresholds in the same circuit at once Commonly used alongside heating element 4391960 Direct drop-in replacement for both original components Replaces 279548, 2796769, 279769VP, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AP3094224, PS334278, WP3390291, AP6008306, 3390291, 696397, and PS11741441 Compatible with Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Kit Part Number 279769 Kit Contents 1x High-Limit Thermostat (3390291), 1x Thermal Cut-Off Fuse (3977394) Condition Genuine OEM Brand Whirlpool High-Limit Thermostat Rating L250-80F (~250°F, auto-resetting) Thermal Fuse Rating 352°F (one-time, non-resettable) Companion Heating Element 4391960 (commonly used together) Repair Difficulty Easy to Moderate — basic tools required Compatible Brands Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, Admiral Installation Notes ⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel, near the heating element and blower housing where both components are mounted. Photograph the wiring connections before disconnecting anything, since the thermostat and fuse can be easy to swap positions by mistake. Remove each old component from its mounting position, noting orientation, and disconnect its wiring. Before reassembling, fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. When the thermal cut-off fails, it usually indicates a venting problem, and failing to correct that airflow issue will cause repetitive failures even with these new parts installed. Install the new 3390291 thermostat and 3977394 thermal fuse from this kit in the same positions as the parts they replace, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), work gloves. Frequently Asked Questions My clothes are coming out extremely hot, hot enough to burn my hands. Is this the right kit? Yes, this is a documented symptom this kit addresses. If the high-limit thermostat fails to regulate temperature correctly, the dryer can run far hotter than it should, producing dangerously hot clothing at the end of a cycle. Whirlpool's own parts support has specifically pointed customers with this exact complaint toward this kit. Stop using the dryer if you notice this symptom and replace both components promptly. Why do I need to replace both the thermostat and the fuse together? These two parts protect the same circuit at different thresholds and tend to fail from the same underlying cause. If the high-limit thermostat isn't regulating temperature correctly, the thermal fuse often ends up blowing as the backup safety measure. Replacing only one risks the other failing again shortly after, so they're sold and serviced together as a set. I replaced this kit and the dryer failed again. What should I check? This is a strong sign the underlying cause — almost always restricted airflow — was never addressed. Thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. Failing to correct a venting issue will cause repetitive failures of this kit even when it's brand new. Should I replace the heating element at the same time? It's worth considering if your dryer's heating element (commonly 4391960 on compatible models) is original and has been running alongside a failing thermostat, since sustained overheating can stress the element as well. It's not required, but since you'll already have the panel open for this repair, it's a reasonable time to inspect the element for visible damage. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same temperature thresholds and mounting configuration as the high-limit thermostat and thermal cut-off fuse originally installed in your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 8181651 Washer Door Striker  Replaces Part Numbers: WP8181651, 8181651, 906446, AP6011711, PS11744910. Description: This Door Strike is a replacement part for specific Maytag, Kenmore, Whirlpool washing machine models. This component is responsible for providing a secure and proper closure for the washer door, ensuring it seals tightly during operation. This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less

6322FR2046CCM Washer Thermistor Assembly Monitors water temperature Fits LG and Kenmore Washer Replaces Part Numbers:6322FR2046C, 6322FR2046B, 1268202, 6322FR2046F, 6322FR2046W, AH3528953, EA3528953, AP4445159, PS3528953. Description: This Thermistor Assembly is a replacement part for select front loading LG washing machine models. It plays an important role in monitoring and regulating temperatures during heated wash cycles. The thermistor detects temperature changes within the wash drum and sends this information to the control board to ensure clothes are washed at the optimal temperature.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

4392067 Genuine OEM Whirlpool Dryer Repair Kit — Belt, Rollers & Idler (27") The 4392067 is a Genuine OEM Whirlpool dryer maintenance and repair kit that contains all the components most commonly replaced when a 27-inch Whirlpool-family dryer becomes noisy, stops tumbling, or starts vibrating — specifically the drum drive belt, all four drum support rollers, the idler pulley, tri-ring retaining clips, a washer, and installation instructions. Installing all of these components together in a single repair restores smooth, quiet drum rotation and eliminates the most common causes of dryer noise and drum drive failure in one visit. As a Genuine OEM kit assembled by Whirlpool to factory specifications, the 4392067 includes the belt (661570V), four rollers (WPW10314173), idler pulley (279640), nine tri-rings, one washer, and instructions. Compatible with 27-inch Whirlpool, Kenmore 110-series, Maytag, Roper, Estate, Crosley, Amana, and Admiral dryers built in 1965 or later. Important: the included belt (661570V, 93-1/2" x 1/4", 4-rib) is correct for many models but does not fit all — verify that 661570V is the correct belt for your specific model before ordering. It directly replaces AP3109602, 2015, 4392067VP, 587637, 80047, AH373088, EA373088, EAP373088, and PS373088. Installs in 45–60 minutes with basic hand tools. Quick Answer The 4392067 Genuine OEM Whirlpool Dryer Repair Kit fixes 27-inch Whirlpool-family dryers that are squealing, thumping, rumbling, or where the drum has stopped spinning. All-in-one kit: belt 661570V + 4 rollers (WPW10314173) + idler pulley (279640) + 9 tri-rings + washer + instructions. Genuine OEM. Important: belt 661570V fits many but not all models — verify your belt part number before ordering. Replaces AP3109602, 2015, 4392067VP, 587637, PS373088. Common Problems This Kit Fixes Loud squealing, squeaking, or thumping noise during the drying cycle Rumbling or grinding noise — worn drum support rollers Drum not spinning — broken or stretched drive belt Motor running but drum still — belt has snapped Belt repeatedly slipping — worn idler pulley no longer maintaining belt tension Burning rubber smell — slipping belt from a failed idler pulley Extended drying times — drum not rotating at correct speed due to belt or roller wear Excessive vibration during the drying cycle What's in the Kit Part 1 Drum Drive Belt — 661570V 93-1/2" long x 1/4" wide · 4-rib profile · Wraps around the drum and connects to the motor pulley and idler pulley to spin the drum · Important: 661570V is correct for many but not all compatible models — verify this belt number fits your specific dryer before ordering Parts 2–5 (qty: 4) Drum Support Rollers — WPW10314173 (set of 4) Cylindrical rubber-and-plastic wheels that support the drum rim as it rotates · LG/Whirlpool 27" dryer platform · Replace all 4 at the same time for even drum support Part 6 Idler Pulley Assembly — 279640 Spring-tensioned pulley wheel that presses against the drive belt to maintain correct belt tension · Pulley wheel only (not the arm) — mounts on the existing idler arm inside the dryer Hardware 9 Tri-Ring Retaining Clips + 1 Washer + Instructions Tri-ring clips secure the drum rollers to their mounting shafts · Washer provides proper spacing at roller shaft · Instruction sheet included Replaces Part Numbers This dryer repair kit directly replaces the following OEM and cross-reference part numbers: 661570V, 279640, WPW10314173, 8536974, 4392067, 2015, 4392067VP, 587637, 80047, AH373088, EA373088, AWP39353, EAP373088, PD00002451, AP3109602, PS373088. Contact our support team with your model number if you need confirmation before ordering. Compatibility This repair kit is compatible with 27-inch gas and electric dryers from the following brands (built 1965 or later): Whirlpool dryers (27" WED, WGD, Cabrio, Duet, and related series) Kenmore / Sears dryers — 110-series (Whirlpool-built models) Maytag dryers (Bravos XL and related series) Roper dryers Estate dryers Crosley dryers Admiral dryers Amana dryers (select models) Important — Belt Compatibility: The belt included in this kit is part number 661570V (93-1/2" x 1/4", 4-rib). This belt is correct for many 27-inch Whirlpool-family dryers but does not fit all compatible models. Before ordering, verify that 661570V is the correct belt part number for your specific dryer model. If your dryer uses a different belt, the rollers and idler pulley in this kit will still fit, but you will need to order the correct belt separately. Key Features Genuine OEM kit assembled by Whirlpool — all components manufactured to factory specifications All-in-one repair: belt (661570V) + 4 rollers (WPW10314173) + idler pulley (279640) + tri-rings + washer + instructions in a single box Replaces all the most commonly worn drum drive components in a single repair — eliminates the need for separate part orders and multiple teardowns For 27-inch Whirlpool-family dryers built 1965 or later Belt 661570V: 93-1/2" long x 1/4" wide, 4-rib — verify fit for your model before ordering Idler pulley (279640) is the pulley wheel only — mounts on the existing idler arm Compatible with Whirlpool, Kenmore 110-series, Maytag, Roper, Estate, Crosley, Admiral, and Amana Installs in 45–60 minutes with basic hand tools Product Specifications Kit Part Number 4392067 Condition Genuine OEM Application 27-inch Gas and Electric Dryers (built 1965 or later) Belt Included 661570V — 93-1/2"L x 1/4"W, 4-rib (verify fit for your model) Rollers Included 4x WPW10314173 drum support rollers Idler Pulley Included 279640 (pulley wheel only — not the arm) Hardware Included 9 tri-ring retaining clips, 1 washer, instructions Compatible Brands Whirlpool, Kenmore, Maytag, Roper, Estate, Crosley, Admiral, Amana Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the top panel by inserting a putty knife under the front edge to release the spring clips, then lift. Remove the front panel to fully expose the drum. Take a photo of the existing belt routing before removing anything. Release the drive belt from the idler pulley and slide it off the drum. Remove the drum and set it aside. Replace all four drum support rollers — remove the old tri-ring clips with needle-nose pliers, slide the old rollers off the shafts, and install the new WPW10314173 rollers with new tri-rings and the included washer. Replace the idler pulley (279640) by pressing the new wheel onto the idler arm shaft. Route the new 661570V belt around the drum (ribbed side against the drum), under the idler pulley, and around the motor pulley. Reinstall the drum, front panel, and top panel. Restore power and run a test cycle. Tools needed: Phillips screwdriver, putty knife, needle-nose pliers, socket set. Frequently Asked Questions How do I know if the belt in this kit (661570V) fits my dryer? The belt included in this kit is 661570V (93-1/2" long, 1/4" wide, 4-rib). To confirm it is correct for your dryer, look up your dryer's model number in an online parts diagram and check the belt part number listed. If the parts diagram shows 661570V or its cross-reference 661570, this kit's belt is correct. If your diagram shows a different belt part number — for example 341241, W10205415, or WP8547157 — the rollers and idler in this kit will still fit your dryer, but you will need to order the correct belt separately. This is the most important compatibility check before purchasing this kit. Is the idler pulley (279640) a complete arm assembly or just the wheel? The 279640 included in this kit is the pulley wheel only — it does not include the idler arm or bracket. It presses onto the existing idler arm shaft inside your dryer. If the idler arm itself is cracked or broken, the arm assembly will need to be replaced separately. On most Whirlpool 27-inch dryers the arm itself rarely fails — it is the wheel bearing that wears out, which is what the 279640 wheel in this kit addresses. Why should I replace all four rollers instead of just the one that's noisy? All four drum support rollers wear at the same rate through the same number of drying cycles. When one roller starts making noise, the other three have experienced the same wear and are likely close behind. Replacing only the noisy roller leaves three worn rollers supporting the drum unevenly, often leading to a repeat repair within months. Since the dryer is already fully disassembled for this repair, replacing all four at once is the most cost-effective and long-lasting approach. How is the 4392067 kit different from the 4392065 kit? Both are Genuine OEM Whirlpool dryer repair kits but for different dryer platforms. The 4392065 is for older Whirlpool 29-inch dryers with the lint screen on top (contains belt 341241, 2 rollers 349241T, idler pulley 691366). The 4392067 is for newer Whirlpool 27-inch dryers with the lint screen inside the door — typically the Duet, Cabrio, Bravos XL, and Thin Twin platforms (contains belt 661570V, 4 rollers WPW10314173, idler pulley wheel 279640). They are not interchangeable — verify your dryer's lint filter location and model series before ordering. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM kit assembled by Whirlpool to factory specifications. All components — belt, rollers, idler pulley, tri-rings, and washer — are the same parts installed in compatible Whirlpool, Kenmore, Maytag, and related brand 27-inch dryers from the factory. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH23X38617 Genuine OEM GE Washer Drain Pump Filter with Seal The WH23X38617 is a Genuine OEM GE replacement drain pump filter with seal, compatible with select GE, GE Profile, and GE 2-in-1 Washer/Dryer Combo models. The pump filter sits inside the drain pump housing and traps lint, coins, hair, and small debris before they reach the pump impeller. Keeping this filter clean and intact is essential for proper drainage — a clogged or damaged filter causes slow draining, standing water in the tub, and can strain the drain pump over time. This genuine OEM part is manufactured by GE to factory specifications and includes both the pump filter and the seal. The seal prevents leaks at the pump clean-out when the filter is installed correctly. The filter body is blue plastic with rubber seal components, measuring approximately 6" L x 3" W x 3" H. It directly replaces part number AP7243923 and installs with a simple counterclockwise removal and clockwise installation — no special tools required. Quick Answer The WH23X38617 Genuine OEM GE Washer Drain Pump Filter with Seal fixes GE washers that drain slowly, leave standing water in the tub, or leak near the pump access panel. The filter traps lint and debris to protect the pump impeller. Includes filter and seal. Blue plastic/rubber, approx. 6" L x 3" W x 3" H. Twist-out installation — no tools needed. Compatible with GE, GE Profile, and GE 2-in-1 Washer/Dryer Combo models. Common Problems This Part Fixes Washer draining slowly or not draining at all after a wash cycle Standing water remaining in the drum at the end of a cycle Water leaking from the pump filter access panel at the front of the washer Error codes related to drain or pump failure on compatible GE models Unusual noise from the drain pump caused by debris reaching the impeller Cracked, stripped, or missing filter cap allowing debris into the pump housing Damaged or deteriorated seal causing leaks at the filter access port Replaces Part Numbers This drain pump filter directly replaces the following part numbers: WH23X38617, WH23X38617, FIX17874614, AGE1014282, PD00090185, AP7243923, PS17874614. Contact our support team with your model number if you need help confirming compatibility before ordering. Compatibility This drain pump filter is compatible with select washers and laundry centers from the following GE product lines: GE front-load washers (select models) GE Profile front-load washers (select models) GE 2-in-1 Washer/Dryer Combo (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Traps lint, coins, hair, and small debris to protect the drain pump impeller from damage Includes both the pump filter and seal — everything needed for a complete replacement Seal prevents water leaks at the pump filter access port when the filter is properly installed Blue plastic and rubber construction — durable and chemical resistant Dimensions: approximately 6" L x 3" W x 3" H Twist-out installation — turns counterclockwise to remove, clockwise to install; no special tools required Should be cleaned regularly (every 1–3 months) and replaced when cracked, stripped, or leaking Product Specifications Part Number WH23X38617 Part Type Washer Drain Pump Filter with Seal Condition Genuine OEM Application Front-load washers and 2-in-1 washer/dryer combos Approximate Dimensions 6" L x 3" W x 3" H Color Blue Material Plastic / Rubber Includes Pump filter and seal Installation Twist-out / twist-in — no special tools required Compatible Brands GE, GE Profile Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before servicing the drain pump filter. Place towels or a shallow pan beneath the filter access panel to catch residual water — there will always be some water remaining in the pump housing when you remove the filter. Locate the pump filter access panel at the lower front of the washer and open or remove it. Turn the old WH23X38617 filter counterclockwise to loosen and remove it. Clear any debris from the filter housing and wipe the area clean. Install the new filter and seal by inserting it into the housing and turning it clockwise until snug — do not overtighten. Close or reinstall the access panel, restore water supply and power, then run a short cycle to verify proper drainage and confirm there are no leaks at the filter port. Tip: Clean the pump filter every 1–3 months as part of regular washer maintenance to prevent buildup. Tools needed: None for the filter itself; a screwdriver may be needed to open the access panel on some models. Frequently Asked Questions What does the drain pump filter do? The drain pump filter catches lint, coins, hair, buttons, and other small items before they can reach the drain pump impeller. Without the filter, debris can jam or damage the impeller — leading to pump failure, loud grinding noises, or a washer that won't drain. The filter also acts as a cleanout access point so you can periodically remove accumulated debris without disassembling the pump. How often should I clean or replace the pump filter? GE recommends cleaning the pump filter every 1–3 months depending on how frequently you run the washer and how much lint your laundry produces. The filter should be replaced rather than just cleaned if it is cracked, stripped at the threads, or if the seal is damaged or missing — a compromised filter or seal will leak water from the access port. Why is water leaking from the front of my GE washer near the bottom? A leak at the lower front of the washer near the pump access panel is most often caused by a damaged or deteriorated pump filter seal, a cracked filter body, or a filter that is not fully tightened. Replacing the WH23X38617 pump filter and seal resolves this in most cases. Make sure the new filter is hand-tightened snugly — do not overtighten, as this can crack the housing. Will there be water when I remove the pump filter? Yes — there is always residual water in the drain pump housing. Before removing the filter, place towels and a shallow pan or tray directly under the access panel to catch the water. The amount varies depending on how much water remains in the washer after the last cycle. Running a drain-only cycle immediately before removing the filter will minimize the amount of water released. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same pump filter and seal that GE installs in compatible models from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout  

Read more less

W11126005CM Dishwasher Wash Vane Sensor Description: This Sensor is a replacement component specifically designed for certain Whirlpool dishwasher models. It plays a crucial role in monitoring cycle conditions like temperature and soil levels to automatically customize wash sequences. Causes of a bad sensor can include leaking or faulty wiring disrupting signals over time, mineral buildup gumming internal mechanisms, or damage from impact. Replaces Part Numbers: W11126005, W11503875, W10380177, W10380483, W10647239, AP6261394, PS12114437. This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: California’s Proposition 65 

Read more less

3205241CM Washer Idler Pulley Spring  Washer Idler pulley spring. Fits Specific Electrolux, Frigidaire laundry centers Models. Replaces Part Numbers:3205241, AH446942, EA446942, AP2132055, PS446942.   This is an aftermarket part that can be used as a replacement for the OEM part.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

Genuine OEM WP95405 Washer Drive Belt The Genuine OEM Whirlpool WP95405 is a washer drive belt, a looped rubber V-belt, 1/2 inch wide and 47-3/8 inches long, that runs between the motor pulley and the drive pulley. When the motor turns, the belt turns the drive pulley, which spins the basket and agitates the clothes. A worn, stretched, or damaged belt can cause squealing at the start of the spin cycle, thumping during spin, longer wash times, or poor cleaning. This is the original Whirlpool part. It is listed for Whirlpool-built washers sold as Whirlpool and Kenmore. Replacing a belt takes some work to access the drive, and belts differ between washer families, so check the part number against your model before ordering. Quick Answer The Genuine OEM WP95405 Drive Belt fixes a Whirlpool or Kenmore washer that squeals or thumps during spin, takes longer to wash, or doesn't spin or agitate properly because the belt is worn or loose. Classic symptom: a squeal when the spin cycle starts, or a basket that spins slowly or not at all while the motor runs. Common Problems This Part Fixes Squealing at the start of the spin cycle Thumping noise during spin Longer wash times or poor cleaning Basket spins slowly or doesn't spin although the motor runs Visibly worn, stretched, cracked, or broken belt Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drive belt directly replaces the following part numbers: WP95405, 95405, 16192, 16358, 21012, 26000095405, 3480, 8201, 8X475, 91261, F341241, LB165, P50-047, AP6013662, AWP48936, EAP11746889, PD00002366, PS11746889 These numbers span several generations of Whirlpool's own part numbering for this belt. Confirm against your washer's parts diagram, or contact our support team, if your model calls out a different number. Compatibility This drive belt is listed for Whirlpool and Kenmore washers, including these examples: Whirlpool LA5700XKW0, 2LA5700XKW0, 3LA5700XKW0, LA5705XKW0, LA6800XPW1, LA3800XPW1 Kenmore 11082620, 11075601, 11075193, 11076529, 11080094, 11076065 Note: The models above are a sample, not a full list. Washer belts differ in length and profile between washer families, so check your model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool washer drive belt, 1/2" wide x 47-3/8" long V-shape, cog-tooth belt profile Connects the drive motor to the drive system so the basket turns Resolves squealing, thumping, and slow-spin problems caused by a worn belt Replaces many older Whirlpool belt numbers, including 95405 Fits Whirlpool and Kenmore washers Product Specifications Part Number WP95405 OEM Part Number WP95405 Part Type Washer Drive Belt Belt Size 1/2" Wide x 47-3/8" Long Belt Profile V-Belt, Cog (Notched) Tooth Condition Genuine OEM Application Whirlpool & Kenmore Washers Installation Notes ⚠️ Unplug Power Before Installing Unplug the washer before beginning, and wear work gloves to protect your hands. Access to the belt depends on your model, so follow its service guide to reach the motor and drive pulleys. Note how the old belt is routed, remove it, and fit the new belt on the same pulleys. Check that it is seated in the pulley grooves and tensioned as shown in your service guide before reassembling. Reviewers rate this repair from moderate to very difficult, taking roughly 1 to 2 hours or more. Frequently Asked Questions My washer squeals when the spin starts. Is this the part I need? A worn or loose drive belt is a common cause. One reviewer reports a squeal at the start of spin that went away after the belt was replaced and tightened. Is WP95405 the same as 95405? Yes. 95405 is the older Whirlpool number, and WP95405 is the current number. This belt also replaces the other older numbers in the Replaces list above. Is this an easy repair? It depends on your model. Reviewers rate it from moderate to very difficult, usually taking 1 to 2 hours or more, because the drive has to be reached and the belt reseated. Follow your model's service guide. Will this fit my washer? It is listed for many Whirlpool and Kenmore washers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 5221ER1003A Washer Water Inlet Valve Three solenoids. Washer cold water inlet valve assembly. 120V AC Washer cold water inlet valve assembly. Replaces Part Numbers: 5221ER1003A, 1268130, 5221ER1003C, 5221ER1003D, 5221ER1003F, AH3527452, EA3527452, AP4442608, PS3527452. 5220FR2075L, 4322702, AGM73269503, AP5986564, PS11728995. Description: This Water Inlet Valve Assembly is a replacement part for specific Kenmore, LG washing machine models. This critical component regulates the flow of water into the washing machine tub, ensuring the proper water supply for various wash cycles and functions.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO 3387134 - 3392519 Dryer Cycling Thermostat and Thermal Fuse Set - Compatible with Whirlpool, Kenmore, Maytag Product Description Maintain safe and efficient dryer operation with the XPARTCO 3387134 - 3392519 Dryer Cycling Thermostat and Thermal Fuse Set. This replacement kit includes one cycling thermostat (3387134, L155-25) and one thermal fuse (3392519), designed as a replacement for select Whirlpool, Kenmore, Maytag, and other compatible dryers. The cycling thermostat regulates drum temperature, while the thermal fuse prevents overheating by cutting power if temperatures exceed safe limits. This set addresses issues like overheating, insufficient heat, no heat, or prolonged drying times. Test the thermal fuse first if the dryer won't heat, as it typically fails before the thermostat. Note: Includes (1) cycling thermostat and (1) thermal fuse. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: Cycling Thermostat: WP3387134, 3387134, 3387135, 3387139, 3-6910, 306910, 326801, 661512, L150-15F, L155-25F, AP6008270, PS11741405. Thermal Fuse: 3392519, WP3392519, 3388651, WE4X857, G4AP0500, 6L4101091C, ET401, 3388651, 694511, 80005, PS11741460, AP6008325. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: LE5700XKW0, LE5920XKW0, WED4815EW1, WED4910XQ1, WED5300SQ0 Kenmore: 110.97591420, 110.97591220, 110.97592420, 110.60072990 Maytag: MDE5500AYW, MDE6000AYW, MDE7600AYW Roper: RED4440VQ1, REX5634KQ1 Amana: NED4655EW0 KitchenAid: KEYE760WWH0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Amana, KitchenAid, and other dryers. 🔧 Specifications: Replacement kit with one cycling thermostat (L155-25 SPST, 120V, 2W) and one thermal fuse (250°F limit, non-resettable). 💪 Reliable Performance: Regulates drum temperature and prevents overheating for safe, efficient drying. 🛠️ Easy Installation: Requires a screwdriver and pliers; typically installed in 15–30 minutes. 🛡️ Effective Fixes: Resolves overheating, insufficient heat, no heat, or prolonged drying times. Product Specification Part Number: XPARTCO 3387134 - 3392519 Component Type: Dryer cycling thermostat and thermal fuse kit Material: Plastic and metal Electrical Specs: Cycling Thermostat: 120V, 2W; L155-25 SPST, opens at 155°F, closes at 130°F  Thermal Fuse: 250°F limit, 125/250V, non-resettable Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running safely and efficiently today! Add to cart now for a reliable fix!

Read more less

W11244231 Genuine OEM Whirlpool Washer Drain Hose The W11244231 is a genuine Whirlpool OEM drain hose for Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers. This flexible tube carries used water from the washer tub to your house drain after every wash cycle, connecting the washer's outlet to your standpipe or utility sink drain connection. This hose is approximately 4 feet long and ships as a kit that includes a clamp. Over time, normal wear and tear, exposure to high water pressure or temperature, or physical damage from kinks and pinches can cause the hose to crack, bulge, or leak. A failing drain hose typically shows up as water leaking around the hose connections or along its length, slow or improper draining, or visible cracks and bulges in the hose material. It directly replaces W10221546, W10769870, W10821090, W11203364, W11249137, W10826733, W11199768, W11199820, AP6339776, and PS12578897. Quick Answer The W11244231 Genuine OEM Whirlpool Washer Drain Hose fixes Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers with a cracked, bulging, or leaking drain hose, slow draining, or a missing hose. Approximately 4 feet long, includes clamp. Replaces W10221546, W10769870, W10821090, W11203364, W11249137, W10826733, W11199768, W11199820, AP6339776, PS12578897. This is a separate part from our W11281268 drain hose listing, which fits a different set of washer models — always confirm your exact model number before ordering. Common Problems This Part Fixes Water leaking around the hose connections or along its length Slow draining or improper drainage of the tub Visible cracks, bulges, or damage to the hose material Missing drain hose on a newly acquired or moved washer Reduced washer efficiency from a clogged, worn, or damaged hose Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drain hose directly replaces the following OEM and cross-reference part numbers: W11244231, W10826733, W10221546, 4814009, W10769870, W10821090, W11199768, W11199820, W11203364, W11249137, AP6339776, AWP43752, OEM19019337, PD00045186, PS12578897 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain hose is compatible with select Whirlpool washers, and also fits select Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers built on the Whirlpool platform, spanning Whirlpool series 1CWTW4, 2DWTW, 3DWTW, 3LWTW, 3NWTW4800, 3SWTW4800, and 4GWTW, and Maytag series 3LMVWC, 4GMVW, 4KMVW, 4KNTW, 7MMVW, and MVWX6, including specific model numbers such as: MVWX655DW1, NTW4516FW3, VAW3584GW0 WTW4816FW2, WTW5000DW1, WTW5000DW2, WTW5000DW3, WTW9500EC0 WTW5100HC0, WTW5500BW0, WTW5600XW0, WTW5700AC0, WTW5800BC0, WTW6120HC0 WTW7000DW0, WTW8000DW0 ITW4871FW0, ITW4871FW1, ITW4871FW2 4KMVWC415FW0, 4KMVWC430JW0, 7MWTW1504DQ0 Kenmore 11026112310 Note — not the same as W11281268: This is a separate part from our W11281268 drain hose listing, which fits a different set of Whirlpool, Maytag, and Amana washer models with its own cross-reference set. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which hose your washer needs. Key Features Genuine Whirlpool OEM part — factory-specified length and fitting design Carries wastewater from the washer to your house drain during the drain cycle Resolves "leaking around connections," "slow draining," and "cracked or bulging hose" symptoms Approximately 4 feet long Ships as a kit including a clamp Direct drop-in replacement — matches the original fitting and length Replaces W10221546, W10769870, W10821090, W11203364, W11249137, W10826733, W11199768, W11199820, AP6339776, and PS12578897 Compatible with Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, and Roper washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11244231 Part Type Washer Drain Hose Kit Condition Genuine OEM Brand Whirlpool Length Approx. 4 feet Includes Clamp Related Part W11281268 (6' hose, different model fitment, sold separately) Repair Difficulty Easy — basic hand tools, novice repair experience Quantity 1 drain hose kit Compatible Brands Whirlpool, Maytag, Kenmore, Amana, Crosley, Admiral, Inglis, Roper Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Transfer Your Old Clamps To The New Hose Disconnect power at the outlet, or shut off the house circuit breaker for the appliance, and shut off the water supply before beginning. Wear work gloves. Remove the back panel of the washer, then the lower front access panel to access the drain hose connection. Place a towel down before disconnecting any hoses to catch any remaining water. Disconnect the old hose from the washer's outlet spout and from your standpipe or drain connection. Transfer your existing hose clamps onto the new W11244231 hose during installation. Fit the new hose over the outlet spout and secure the clamp, then reconnect the other end to your house drain. Reinstall the lower front access panel and back panel. Restore the water supply and power, then run a test cycle to confirm the hose is secure with no leaks. Tools needed: multi-screwdriver, standard pliers, work gloves, towel. Frequently Asked Questions My washer is leaking. Is this the right part? It's worth checking, especially if the leak appears to come from around the hose connections or along its length rather than from the washer's tub or valve area. A cracked, bulging, or worn drain hose is a documented cause of leaking and can be resolved by replacing the hose to restore proper drainage. Is this the same as your W11281268 listing? No, these are two separate genuine Whirlpool drain hoses that fit different sets of washer models, with their own distinct cross-reference lists. Always confirm your exact model number against the compatibility list for each listing rather than assuming either hose is a universal fit. Do I need to buy new hose clamps separately? This hose kit includes a clamp, but you'll still need to transfer your existing clamps from the old hose for any connections that don't come with a new one included. Keep your old hardware on hand during the swap rather than discarding it with the old hose. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original length and fitting configuration of the drain hose originally installed on your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 5304512529 Microwave Door Switch – Compatible with Frigidaire, Electrolux, and Kenmore Microwaves Product Description Ensure safe and reliable operation with the XPARTCO 5304512529 Microwave Door Switch. This high-quality aftermarket replacement detects when the microwave door is closed, allowing the appliance to run safely. A faulty switch can cause the microwave not to start, stop mid-cycle, or operate with the door open — a serious safety concern. Replacing it with this durable XPARTCO switch restores proper interlock function and dependable performance. Replaces Part Numbers 5304512529, 4584691, PD00051808, EAP12365114, AP6278576, PS12365114. Compatibility This replacement door switch fits select Frigidaire, Electrolux, and Kenmore microwave models. Example compatible models include (but are not limited to): Frigidaire FFMV1645TS, Electrolux E30MO75HPS, and Kenmore 790.80353310. Always verify your microwave’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to meet OEM safety and performance standards ⚡ Restores Safe Operation – Ensures microwave only operates when the door is securely closed 💰 Budget-Friendly Fix – High-quality alternative to expensive OEM replacements 🛠️ Quick Installation – Direct-fit replacement; installs easily with basic tools 🛡️ Fixes Common Issues – Solves no-start, mid-cycle shutdowns, or unsafe door operation 📐 Product Specification Part Number: 5304512529 Component Type: Microwave Door Interlock Switch Material: Heat-resistant plastic housing with copper terminals Mounting: Snap-in bracket installation Operating Conditions: Designed for high-voltage microwave circuits Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, flathead screwdriver ⚠️ Safety First: Always unplug the microwave before servicing. Microwave capacitors can retain dangerous voltage even when unplugged — use extreme caution or contact a qualified technician. Steps: Disconnect power and remove the microwave cover. Locate the door latch assembly containing the switches. Disconnect wiring connectors and remove the old switch. Install the new XPARTCO 5304512529 door switch into the same slot. Reconnect wiring, reassemble the cover, and test door operation. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Protect your microwave’s performance and safety — Add to Cart Now for a reliable, budget-friendly replacement!

Read more less