Search results for "washer pulley"

WH22X38697 Washer Genuine Control Board Fits Specific GE Washer Model Main Control Board Fl Washer Le W/instructions Replaces Part Numbers: WH22X38697, WH22X37837, WH22X36638, WH22X32458, WH22X35518, WH22X30897, WH22X29546, WH22X32058, WH22X34660, WH22X36858, WH22X37838, AP8054699, PS17874598.

Read more less

XPARTCO DC97-15459G Washer Water Valve  The XPARTCO DC97-15459G is an aftermarket replacement water inlet valve assembly compatible with a wide range of Samsung top-load washers. This valve mounts at the rear of the washer and controls the flow of water into the drum, opening electronically when the control board calls for a fill and closing once the target water level is reached. It connects via five terminal connections to the wiring harness and to the hot/cold supply hoses. When this valve fails, the washer commonly won't fill with water, fills very slowly, overfills, or continues to trickle water even when powered off — the last of which points to a valve that isn't sealing properly rather than an electrical fault. It directly replaces DC97-15459G, 3276197, AP5623056, ASM1220342, EAP4220861, PD00007887, PS4220861. Sold individually; does not include wire harness or mounting screws. Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO DC97-15459G Washer Water Valve fixes Samsung top-load washers that won't fill, fill slowly, overfill, or leak/drip water even when the washer is unplugged. 5-terminal connection for wiring and hot/cold hose lines. Sold individually — wire harness and mounting screws not included. Replaces DC97-15459G, 3276197, AP5623056, ASM1220342, EAP4220861, PD00007887, PS4220861. Classic symptom: washer trickles water into the drum even when it's completely powered off. Common Problems This Part Fixes Washer won't fill with water at all Washer fills very slowly or takes much longer than normal Washer overfills or keeps adding water past the normal level Water trickles or leaks into the drum even when the washer is off Leaking or dripping at the water inlet connection point Error code related to water fill or water level on the display Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: DC97-15459G, 3276197, AP5623056, ASM1220342, EAP4220861, PD00007887, PS4220861 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with a wide range of Samsung top-load washers, including: Samsung WA45H7200AP/AW, WA48H7400AP/AW, WA48J7770AP/AW Samsung WA50F9A6/7/8 series, WA50K8600AW, WA50M7450AP/AW Samsung WA52J8700AP/AW, WA52M7750AV/A4 and related WA52M7750 series Select Kenmore washers (Samsung-built models) Note: This valve is sold individually and does not include the wire harness or mounting screws — reuse your existing hardware during installation. Always verify your appliance model number before ordering. Contact our support team with your model number if you're unsure. Key Features Direct-fit replacement Samsung washer water inlet valve assembly Resolves "won't fill," "slow fill," "overfilling," and "leaking when off" symptoms Electronically controlled valve opens/closes based on control board signal 5-terminal connection for wiring harness and hot/cold hose lines Replaces DC97-15459G, 3276197, AP5623056, ASM1220342, EAP4220861, PD00007887, PS4220861 Compatible with a wide range of Samsung top-load washer models Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number XPDC97-15459G OEM Part Number DC97-15459G Part Type Washer Water Inlet Valve Assembly Condition Aftermarket Replacement Terminals 5-terminal wiring/hose connection Sold As Individually (wire harness and screws not included) Application Samsung Top-Load Washer Water Supply Compatible Brands Samsung, Kenmore Installation Notes ⚠️ Shut Off Water Supply and Unplug Washer Before Starting Turn off both the hot and cold water supply valves and disconnect power to the washer before beginning. Pull the washer away from the wall for access to the rear panel. Disconnect the hot and cold water supply hoses from the old valve — have a towel ready to catch residual water. Photograph the wiring before disconnecting, then unplug the wire harness connectors from the old valve. Remove the mounting screws holding the valve to the cabinet and remove the old valve. Install the new DC97-15459G valve in the same position using your existing mounting screws (not included with this part) and reconnect the wire harness, matching your photos. Reconnect the hot and cold supply hoses, making sure they're threaded onto the correct ports. Turn the water supply back on and check for leaks at the hose connections before restoring power. Run a test cycle to confirm the washer fills correctly and doesn't leak. Tools needed: adjustable pliers or channel locks (for hose connections), Phillips and flat-head screwdrivers. Frequently Asked Questions My washer trickles water into the drum even when it's unplugged — is this the part? Yes, this is a classic symptom of a water inlet valve that isn't sealing properly. Since the valve is the only thing standing between your home's pressurized water supply and the drum, a valve that won't fully close will let water trickle through even with zero power to the washer. This is different from an electrical fill problem, which typically shows up as the washer not filling at all rather than filling when it shouldn't. Does this include the wire harness and mounting screws? No — this valve is sold individually. You'll reuse your existing wire harness connector and mounting screws from the old valve during installation. Will this fit my Kenmore washer? This valve fits select Kenmore washers that were built by Samsung and share this platform's water valve design. Confirm your appliance model number before ordering, since not all Kenmore washers use this valve. Do I need to shut off the water supply to replace this? Yes — always shut off both the hot and cold water supply valves before disconnecting the hoses from the old valve. Skipping this step will result in water spraying from the open supply lines once the hoses are disconnected. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO EXP571 Dryer Door Catch The XPARTCO EXP571 is an aftermarket replacement door catch for electric and gas dryers from Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse, and LG. The door catch is the small plastic part the dryer door latches onto to stay securely shut during a cycle. Keeping the door tightly closed holds heat and airflow inside the drum, so clothes dry efficiently. Over time, regular wear, physical damage, or a door that has drifted out of alignment can cause the catch to crack, wear down, or lose its grip, and the door stops latching reliably. Made from durable plastic, this is a direct-fit replacement with a simple snap-in installation — no tools required. Because the same catch design was used across several appliance families, it carries a long cross-reference list spanning Whirlpool, Frigidaire, and GE part numbers; see the Replaces list below. Each order includes 1 door catch. Quick Answer The XPARTCO EXP571 Dryer Door Catch fixes a dryer door that won't stay closed, won't latch properly, or pops open during a cycle because the catch is cracked, worn, or damaged. Durable plastic, snap-in install with no tools, 1 catch per order. Fits Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse, and LG dryers. Classic symptom: you have to push or hold the door shut, or it swings open mid-cycle and heat escapes. Common Problems This Part Fixes Dryer door won't stay closed or pops open during a cycle Door doesn't latch with a firm, positive click Visibly cracked, broken, or worn catch Heat escaping around the door, leaving clothes damp after a full cycle Door feels loose or misaligned when closed Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door catch directly replaces the following part numbers: WP71002106, WP3389441, 3389441, 71002106, AWP47565, PD00004499, AP6010685, PS11743869, AP6008299, PS11741434, WE1X1195, AGE1230465, AP2042209, PS266896, 131658800, AFR14189, AP2107362, PD00000626, PS418433, 5307521419, 10690002, 10690001, AFR14189, AP4450746, PD00000626, PS418433 This one catch design was sold under the part numbers of several manufacturers: Whirlpool/Maytag (WP71002106, WP3389441), Frigidaire/Electrolux (131658800, 5307521419), and GE (WE1X1195, WE1X1153, WE01X10023, and related). The AP/PS-prefixed numbers are third-party catalog cross-references for the same physical part. Compatibility This door catch is used on dryer models from the following brands: Whirlpool, Maytag, Amana, and Kenmore (Whirlpool-built) dryers Frigidaire, Electrolux, Crosley, White-Westinghouse, and Kenmore (Frigidaire-built) dryers GE dryers Select LG dryers Note: Because this catch was used across so many brands and model years, a full model-number list can't be shown here. The safest way to confirm fit is to match the number on your old catch, or on your dryer's parts diagram, against the Replaces list above rather than relying on brand alone. Contact our support team with your model number and we'll verify before you order. Key Features Aftermarket replacement dryer door catch Durable plastic construction for long-lasting use Simple snap-in installation — no tools required Holds the door securely closed to keep heat and airflow in the drum Cross-references to Whirlpool, Frigidaire, GE, and other OEM numbering 1 door catch per order Product Specifications Part Number EXP571 OEM Part Number WP71002106, 131658800, WE1X1195 Part Type Dryer Door Catch Condition Aftermarket Replacement Material Plastic Quantity 1 Door Catch Installation Snap-In, No Tools Required Application Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse & LG Dryers Installation Notes ℹ️ No Tools Required Unplug the dryer before starting as a general safety precaution. Open the dryer door and locate the worn or broken catch the door latches onto. Pull or pry the old catch free from its mounting position, then press the new catch into the same opening until it snaps firmly into place. Close the door and confirm it latches with a positive click and stays shut. If the door still won't seat or latch evenly after the swap, check the door's alignment and hinges, since a misaligned door can wear out a new catch quickly. Frequently Asked Questions My dryer door won't stay shut — is this the part I need? Very likely. A cracked, worn, or damaged door catch is a common reason a dryer door won't latch or pops open mid-cycle. Inspect the old catch for cracks or wear; if it looks damaged, replacing it should restore a firm latch. Will this fit my dryer? I have a Whirlpool, Frigidaire, or GE. This catch is cross-referenced to part numbers from all three families, plus several others. Match the number on your old catch or your dryer's parts diagram against the Replaces list above. If you're unsure, contact our support team with your model number and we'll confirm fit before you order. Do I need tools to install it? No. It's a simple snap-in design — remove the old catch and press the new one into place until it clicks. How many catches come in this order? Each order includes 1 door catch. The door still doesn't close right after replacing the catch. What else could be wrong? A door that has drifted out of alignment can keep a new catch from seating properly and wear it out fast. Check the door hinges and alignment against the cabinet opening. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

EXPW79SC (8 Pack) Washing Machine Fill Hose Gasket with Screen 8 Pack compatible with 5/ 8 inch washing machine and 3/4 inch garden hose Fine Screen the rubber washer with stainless steel filter mesh, serves as a flow restrictor can reduce the waste of water effectively     

Read more less

XPARTCO MDS47123602 Washer Door Boot Gasket – Compatible with LG Front-Load Washers Product Description Stop leaks and restore proper sealing with the XPARTCO MDS47123602 Washer Door Boot Gasket. This high-quality aftermarket replacement forms a watertight seal between the washer door and tub, preventing water from leaking during wash and spin cycles. A worn, torn, or mold-damaged gasket can lead to leaks, odors, or excessive vibration. Replacing it with this durable XPARTCO gasket provides long-lasting protection and reliable washer performance. Replaces Part Numbers MDS47123602, MDS64237201, MDS64237202, MDS47123612, EAP3535210, PD00028934, AH3535210, EA3535210, AP5218575, PS3535210. Compatibility This replacement door boot gasket fits select LG front-load washers. Example compatible models include (but are not limited to):LG WM2650HWA, WM3470HVA, WM3570HWA, WM8000HVA, and WM3997HWA. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM fit, thickness, and sealing performance 💧 Leak-Proof Design – Forms a tight seal to prevent water escaping from the washer door 🌿 Mold-Resistant Material – High-grade rubber reduces mildew and odor buildup 🛠️ Durable Construction – Built to withstand heat, detergent, and high-spin vibration 🛡️ Fixes Common Issues – Solves leaks, mold/mildew odor, door seal tears, or water pooling 📐 Product Specification Part Number: MDS47123602 Component Type: Washer Door Boot Gasket (Door Seal) Material: High-strength, mold-resistant rubber Color: Gray (standard for LG models) Mounting: Installed between front tub and door frame using clamps Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, spring clamp tool (recommended), pliers ⚠️ Safety First: Always unplug the washer before installation to prevent electrical shock. Steps: Remove the washer top and front panel for access. Release the outer retaining spring clamp and remove the old gasket edge. Detach the inner clamp from the tub and remove the old gasket completely. Align and install the new XPARTCO MDS47123602 gasket around the tub opening. Reinstall inner clamp, then secure the outer clamp around the door frame. Reassemble the washer and perform a quick rinse cycle to test for leaks. ⏱️ Time Required: 30–45 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Stop washer leaks the right way — Add to Cart Now for a durable, budget-friendly replacement!

Read more less

XPARTCO W11457841 Washer Lid Latch Strike The XPARTCO W11457841 is an aftermarket replacement washer lid latch strike compatible with select Whirlpool, Maytag, and Kenmore HE top-load washers — including the Whirlpool WTW5100, WTW5105, WTW6120, WTW7120, WTW8120, WTW8127 series, and the Maytag MVW6200, MVW6230, MVW7230, MVW7232, MVW8230 series. The lid latch strike is the plastic component attached to the underside of the washer lid that physically engages the lid lock mechanism when the lid is closed. As the lid lowers into place, the latch strike enters the lock slot and activates the lid switch — signaling the control board that the lid is securely closed and the washer is safe to start agitation and spin. When the lid latch strike fails — typically by breaking off, cracking, or wearing down — the lid lock can't be properly activated, and the washer will not start, will stop mid-cycle, or will refuse to advance to the spin cycle. This W11457841 aftermarket replacement is built to OEM-equivalent specifications and supersedes the earlier W11091027. It also replaces 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028. Installation is fast and simple — a counterclockwise twist removes the old strike, and a clockwise twist installs the new one. Installs in under 5 minutes, no special tools required. Quick Answer The XPARTCO W11457841 Washer Lid Latch Strike fixes Whirlpool, Maytag, and Kenmore HE top-load washers that won't start, won't lock the lid, stop mid-cycle, or won't advance to spin because the lid strike is broken or worn. Plastic latch strike that attaches to the underside of the washer lid and activates the lid lock and switch. Twist-in installation. Genuine OEM. Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, PS16218028. Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series. Common Problems This Part Fixes Washer not starting — lid latch strike not engaging the lid lock Lid won't lock at the start of the cycle Washer stops mid-cycle with a lid-related fault Washer fills with water but won't agitate or advance to spin Lid latch strike visibly broken, cracked, or missing on the underside of the lid Latch strike worn down — physically fits the lock slot but no longer activates the lid switch Repeated lid lock errors despite the lid appearing to close normally Replaces Part Numbers This washer lid latch strike directly replaces the following OEM and cross-reference part numbers: W11457841, W11091027, AP6987306, AWP44638, PD00061788, EAP16218028, PS16218028. W11457841 is the current production part superseding W11091027. Contact our support team with your model number if you need confirmation before ordering. Compatibility This lid latch strike is compatible with select HE top-load washers from the following brands and series: Whirlpool top-load washers — WTW5100HC0, WTW5100HC1, WTW5100HC2, WTW5100HW0, WTW5100HW1, WTW5100HW2 series Whirlpool top-load washers — WTW5105HC0, WTW5105HC1, WTW5105HC2, WTW5105HW0, WTW5105HW1, WTW5105HW2 series Whirlpool top-load washers — WTW6120HC0, WTW6120HC1, WTW6120HC2, WTW6120HW0, WTW6120HW1, WTW6120HW2 series Whirlpool top-load washers — WTW7120HC0, WTW7120HW0 series Whirlpool top-load washers — WTW8120HC0, WTW8120HW0 series Whirlpool top-load washers — WTW8127LC0, WTW8127LC1, WTW8127LW0 series Maytag top-load washers — MVW6200KW0, MVW6200KW1, MVW6200KW2, MVW6200KW3 series Maytag top-load washers — MVW6230HC0, MVW6230HC1, MVW6230HC2, MVW6230HW0, MVW6230HW1, MVW6230HW2 series Maytag top-load washers — MVW6230RHW0, MVW6230RHW1, MVW6230RHW2 series Maytag top-load washers — MVW7230HC0, MVW7230HW0, MVW7230HW1 series Maytag top-load washers — MVW7232HC0, MVW7232HW0, MVW7232HW2 series Maytag top-load washers — MVW8230HC0 series Kenmore / Sears top-load washers (Whirlpool-built — select 110-series models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Aftermarket replacement built to OEM-equivalent quality standards — direct fit for compatible Whirlpool platform washers Plastic latch strike attaches to the underside of the washer lid and engages the lid lock mechanism when the lid closes Activates the lid switch to signal the control board that the lid is securely closed and the washer is safe to start Twist-in/twist-out installation — no tools or hardware required; counterclockwise to remove, clockwise to install Current production part — directly supersedes W11091027 Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028 Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series HE top-load washers, plus select Kenmore Whirlpool-built models Fast DIY repair — installs in under 5 minutes Product Specifications Part Number W11457841 Supersedes W11091027 Part Type Washer Lid Latch Strike Condition Aftermarket Replacement Application HE Top-Load Washers (Whirlpool/Maytag/Kenmore platform) Material High-strength plastic Installation Twist-in (clockwise) / twist-out (counterclockwise) — no tools required Mounting Location Underside of washer lid Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer lid and locate the lid latch strike on the underside of the lid — it's the small plastic peg that drops into the lock slot when the lid is closed. To remove the old latch strike: rotate it counterclockwise until the retaining tab breaks free and pulls back, then pull the old latch strike straight out. To install the new W11457841: align it with the mounting hole in the same orientation as the old one, and rotate clockwise until you hear or feel the retainer tab click into place. Close the lid and confirm the latch strike engages the lock slot properly. Restore power, start a test cycle, and confirm the lid locks and the washer begins normal operation. Tools needed: work gloves only — no tools required for the strike itself. Frequently Asked Questions What's the difference between the lid strike, lid lock, and lid switch? These three components work together as a safety system. The lid latch strike (W11457841) is the small plastic peg attached to the underside of the lid that physically enters the lock slot when the lid closes. The lid lock is the mechanism in the washer cabinet that grips the strike and physically locks the lid closed during the spin cycle. The lid switch is the electrical sensor inside the lock assembly that signals the control board when the strike is engaged. If the strike is broken or missing, none of the three can do their job — even if the lock and switch are working perfectly. Replacing just the strike often resolves "won't start" issues without needing to replace the more expensive lock assembly. What is the difference between W11457841 and W11091027? These are the same lid latch strike across production revisions. W11091027 was the earlier OEM part number, and W11457841 is the current part number that superseded it. Both are physically and functionally identical — if your washer's parts diagram shows W11091027, the W11457841 is the correct current replacement, and this aftermarket part covers both numbers. My washer won't start and the lid seems to close normally — could this be the strike? Yes, this is one of the most common symptoms of lid latch strike failure on compatible Whirlpool and Maytag washers. Even though the lid appears to close, if the strike has cracked or worn down it may not physically engage the lock or activate the switch correctly. Visually inspect the latch strike on the underside of the lid — if it's broken, missing, or chipped, replacement is straightforward. If the latch strike looks intact and the washer still won't start, the lid lock assembly itself or the wiring harness may need attention. Do I really not need any tools to install this? Correct — the W11457841 lid latch strike uses a twist-in design with no screws or hardware. To remove the old latch strike, rotate it counterclockwise until the internal retaining tab breaks free, then pull it out. To install the new one, push it into the mounting hole and twist clockwise until it clicks into place. The whole replacement typically takes under 5 minutes once you have the new part in hand. Work gloves are recommended to protect your hands while gripping the small plastic part, but no other tools are needed. Is this a Genuine OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, twist-in mounting design, and lid switch activation function of the original W11457841 lid latch strike used in compatible Whirlpool, Maytag, and Kenmore HE top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

ERP 5220FR2008C - 5220FR2006H Washer Water Valve Set Hot & Cold Side Water Valves ERP 5220FR2008C (Cold Side 4 Ports) Replaces Part Numbers:5220FR2008C, 1345045, AH3527429, EA3527429, AP4441122, PS3527429 ERP 5220FR2006H (Hot Side) Replaces Part Numbers: 5220FR2006H, 1268123, 5220FR1280F, 5220FR2006L, 5220FR2006Q, AH3527427, EA3527427, AP4441935, PS3527427 This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

ERP WD12X10277 Dishwasher Lower Dish rack Roller Axle Single Pack Gray Color Replaces Part Number: WD12X10277, WD12X10075, WD12X10101, WD12X10126, WD12X10261   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO DC96-01703G Washer Water Level Pressure Switch - Compatible with Samsung Washers Product Description Ensure accurate water level control in your washer with the replacement XPARTCO DC96-01703G Washer Water Level Pressure Switch. This replacement pressure switch is designed for select Samsung front-load and top-load washers, sensing and controlling water levels for optimal washing performance. It addresses issues like incorrect water levels, not filling, or error codes (e.g., E6 FA), offering a cost-effective alternative to OEM parts. Note: Includes one water level pressure switch. Disconnect power and water supply before installation. Verify compatibility with your washer model. Replaces part numbers: DC96-01703G, PD00026135, EAP4217083, AP5623035, PS4217083. Compatibility: Compatible with models including but not limited to: Samsung: WF42H5000AW/A2, WF42H5200AP/A2, WF42H5400AF/A2, WF45K6200AW/A2, WF45K6500AW/A2, WF45M5500AP/A5, WF45M5500AZ/A5, WF50K7500AV/A2, WF50K7500AW/A2, WF56H9100AG/A2, WF56H9110CW/A2, WF457ARGSG, WW22K6800AW/A2, WV55M9600AW/A5, WV60M9900AV/A5, WD10J6410AW/ZS Other brands: Select models requiring DC96-01703G Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Samsung front-load and top-load washers requiring DC96-01703G. 🔥 Specifications: Precision-engineered water level pressure switch with 28" air pressure hose, designed for accurate water level sensing and control. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, work gloves; typically installed in 10–15 minutes. 🛡️ Effective Fixes: Resolves issues like incorrect water levels, not filling, motor idling, or error codes (e.g., E6 FA). Product Specification Part Number: XPDC96-01703G Component Type: Washer water level pressure switch Material: Durable plastic housing with metal contacts Terminal Type: Electrical connector. Operating Conditions: Suitable for high-humidity washer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the washer from the power source and water supply before installation. Tools Needed: Phillips screwdriver, work gloves. Process: Access the switch by removing the top or back panel of the washer, disconnect the old switch’s wiring and hose, install the new switch, and reconnect wiring and hose. Ensure secure connections and test for proper operation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your washer running efficiently today! Add to cart now for a budget-friendly fix!

Read more less

WD15X26078 Genuine OEM GE Dishwasher Water Inlet Valve The WD15X26078 is a Genuine OEM GE replacement dishwasher water inlet valve compatible with a wide range of GE, GE Profile, Café, Haier, Hotpoint, RCA, and Kenmore GE-built dishwashers. The water inlet valve is mounted at the base of the dishwasher behind the lower access panel, connecting the household water supply line to the dishwasher's fill circuit. When the control board calls for water during the fill phase, the valve's internal solenoid opens, allowing water to flow into the tub — and it closes the instant the call is dropped, stopping flow precisely at the correct fill level. Without a properly functioning inlet valve, the dishwasher can't fill correctly — leading to poor cleaning performance, error codes, or no wash at all. Rated 120V, 60Hz. Approximate dimensions: 3.75" H x 3.25" W x 3.00" L. Silver/multi-color metal and plastic construction with a deep-threaded, high-quality water inlet for a tight supply-line connection and a secure outlet design that keeps the internal fill hose firmly attached. As a Genuine OEM part manufactured by GE to factory specifications, the WD15X26078 directly replaces 4959029, AP6986683, PS16217027, EAP16217027, and PD00064270. Hard water sediment is a leading cause of inlet valve clogging and failure on GE dishwashers — if your old valve is restricted by mineral buildup, replacement (not cleaning) is the recommended fix, as the internal components are easily damaged during cleaning attempts. Installs in 20–30 minutes with basic hand tools. Quick Answer The WD15X26078 Genuine OEM GE Dishwasher Water Inlet Valve fixes GE, GE Profile, Café, Haier, Hotpoint, and Kenmore dishwashers that aren't filling with water, fill slowly, display the H2O error code, make strange noises or vibration during fill, won't stop filling, or leak from the valve area. 120V, 60Hz. Approx 3.75"H x 3.25"W x 3.00"L. Genuine OEM GE. Replaces 4959029, AP6986683, PS16217027, EAP16217027, PD00064270. Compatible with GDF, GDT, GDP, PDT, PDP, QDP, ZDT, DDT, and Café CDT series dishwashers. Common Problems This Part Fixes Dishwasher not filling with water at all — valve solenoid not opening Dishwasher filling slowly or not getting enough water — valve clogged with hard water sediment H2O error code displayed — insufficient water intake detected Strange noises or vibration during the fill phase — worn valve diaphragm Dishwasher won't stop filling — valve stuck open (overfill/flood risk) Water leaking from the valve area or its connections Dishes not being cleaned properly due to insufficient water fill Wash cycle interrupted or extended due to fill timeouts Valve inlet screen visibly clogged with mineral deposits Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers: WD15X26078, AGE846049, AP6986683, EAP16217027, PD00064270, PS16217027 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: some similar-looking GE valves (such as WD15X24213 or WD15X26140) are different parts — verify your original valve's part number or your dishwasher model number before ordering. Compatibility This water inlet valve is compatible with select dishwashers from the following brands: GE dishwashers — GDF series (GDF510PGM4BB/WW, GDF510PSM4SS/5SS, GDF511PSM5SS, GDF511PGM5WW, GDF530PGM4BB/CC/WW/5WW, GDF530PSM4SS/5SS, GDF530PMM4ES, GDF565SSN3SS, GDF630PFM4DS/5DS, GDF630PGM4BB/WW/5BB, GDF630PMM4ES/5ES, GDF630PSM4SS, GDF640HFM4DS, GDF640HGM4WW/5BB, GDF640HMM4ES, GDF645SGN2BB/WW/3BB/3WW, GDF645SMN2ES/3ES, GDF645SSN2SS/3SS and related) GE dishwashers — GDT series (GDT530PGP5BB, GDT530PSP5SS, GDT535PSMASS, GDT535PSM5SS, GDT565SSN2SS, GDT605PSM5SS, GDT630PFM4DS, GDT630PMM4ES/5ES, GDT630PYM4FS, GDT635HMM4ES, GDT635HSM4SS/5SS, GDT645SGN2BB/WW/3WW, GDT645SMN3ES, GDT645SSN2SS, GDT645SYN2FS, GDT665SBN2TS/3TS, GDT665SFN3DS, GDT665SGN2WW/3WW, GDT665SMN2ES, GDT665SSN3SS and related) GE dishwashers — GDP series (GDP615HFM4DS, GDP645SYN3FS/4FS/8FS, GDP665SYN2FS/3FS/4FS/8F7S and related) GE Profile dishwashers — PDT series (PDT715SBN2TS/3TS, PDT715SFN3DS, PDT715SMN2ES/3ES, PDT715SYN3FS, PDT775SYN2FS/3FS, PDT785SBN2TS, PDT785SYN2FS/3FS/5FS and related) GE Profile dishwashers — PDP series (PDP715SBN3TS, PDP715SYN3FS and related) GE dishwashers — QDP series (QDP555SBN4TS, QDP555SYN4FS and related) GE Monogram dishwashers — ZDT series (ZDT925SIN2II/3II/5II, ZDT925SPN2SS/3SS, ZDT925SSN2SS/3SS/5SS, ZDT985SIN3II, ZDT985SPN5SS, ZDT985SSN5SS and related) GE dishwashers — DDT series (DDT700SBN2TS/3TS, DDT700SFN2DS/3DS, DDT700SGN2BB/WW, DDT700SMN2ES and related) Café dishwashers — CDT series (CDT800P2N2S1-N5S1, CDT805M5N2S5-N4S5, CDT805P2N2S1-N5S1, CDT845M5N2S5-N5S5, CDT845P2N2S1-N5S1, CDT845P3N2D1-N5D1, CDT845P4N2W2-N5W2, CDT855M5N2S5/N3S5/N5S5, CDT855P2N2S1/N3S1/N5S1, CDT875M5N2S5-N7S5, CDT875P2N2S1-N5S1, CDT875P3N5D1 and related) Haier dishwashers (select models using the GE-platform valve) Hotpoint and RCA dishwashers (select GE-built models) Kenmore / Sears dishwashers (select GE-built models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Controls the flow of water into the dishwasher during fill cycles — precise fill for optimal cleaning performance Solenoid-actuated — opens when the control board calls for water and closes the moment the call is dropped Rated 120V, 60Hz — correct electrical specifications for compatible GE-platform dishwashers Approximate dimensions: 3.75" H x 3.25" W x 3.00" L Deep-threaded water inlet for a tight, leak-free supply line connection Secure outlet design keeps the internal fill hose firmly attached Resolves H2O error codes, no-fill, slow-fill, overfill, and fill-noise symptoms Replaces 4959029, AP6986683, PS16217027, EAP16217027, and PD00064270 Compatible with GE GDF/GDT/GDP series, GE Profile PDT/PDP series, QDP series, Monogram ZDT series, DDT series, Café CDT series, plus Haier, Hotpoint, RCA, and Kenmore GE-built dishwashers DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WD15X26078 Part Type Dishwasher Water Inlet Valve Assembly Condition Genuine OEM Application Dishwashers (GE platform) Voltage 120V AC Frequency 60 Hz Dimensions Approximately 3.75" H x 3.25" W x 3.00" L Color Silver / Multiple Colors Material Metal / Plastic Error Codes Resolved H2O (insufficient water intake) Compatible Brands GE, GE Profile, Café, Monogram, Haier, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power at the breaker and shut off the household water supply at the shutoff valve under the sink before beginning. Wear work gloves to protect your hands. Have towels and a shallow dish ready — residual water remains in the supply line and hoses and will spill when disconnected. Remove the lower access panel (baffle) at the front bottom of the dishwasher — typically 2–4 screws. Locate the water inlet valve where the household supply line enters the dishwasher. Photograph the hose and wire connections before disconnecting anything. Disconnect the household water supply line from the valve inlet (use pliers for the larger ingress connection — place the dish underneath to catch leftover water). Disconnect the internal fill hose from the valve outlet (needle-nose pliers help with the smaller egress hose clamp). Unplug the electrical connector that snaps onto the valve solenoid. Remove the mounting screws holding the valve bracket to the frame and lift the old valve out. Install the new WD15X26078 valve in the same position, secure the mounting screws, reconnect the internal fill hose with its clamp, and snap the electrical connector back on. Reconnect the household water supply line to the valve inlet — align the threads carefully and tighten snugly without over-torquing. Turn the water supply back on and use a flashlight to inspect all connections for leaks BEFORE reinstalling the access panel. Restore power and run a test cycle to confirm proper filling with no leaks. Tools needed: Phillips screwdriver, pliers, needle-nose pliers, shallow dish, towels, flashlight, work gloves. Frequently Asked Questions What does the H2O error code mean on my GE dishwasher? The H2O error code on GE dishwashers indicates the control board is not detecting sufficient water intake during the fill phase. Common causes are: a failed or clogged water inlet valve (the most frequent culprit), the household water supply shutoff valve partially closed, a kinked supply line, or low household water pressure. First verify the supply valve under the sink is fully open and the line isn't kinked. If the supply checks out, the WD15X26078 inlet valve is the standard fix — hard water sediment gradually clogs the valve's internal screen and passages, restricting flow until the dishwasher can't fill within its expected time window. Can I clean the old valve instead of replacing it? It's not recommended. While the inlet screen on some valves can be carefully brushed clean, the internal passages and solenoid diaphragm of a sediment-clogged valve are easily damaged during cleaning attempts — a common outcome is a valve that leaks or sticks open after being "cleaned," which risks flooding. Real-world experience (including customer stories with this exact part) shows that attempting to clean a hard-water-clogged valve often breaks it. Given the moderate cost of the OEM replacement versus the flood risk of a compromised valve, replacement is the reliable repair. If your area has hard water, consider this a maintenance item that may need periodic replacement. My dishwasher won't stop filling — is that also this valve? Yes — a valve stuck in the open position is the other failure mode. When sediment or a worn diaphragm prevents the valve from sealing fully closed, water continues to flow into the tub even when the control board has cut power to the solenoid. This can lead to overfilling and potentially flooding through the door or float overflow. If your dishwasher keeps filling past its normal level, or you find water accumulating in the tub between cycles, shut off the water supply at the sink immediately and replace the valve before running the dishwasher again. How do I know this is the right valve for my GE dishwasher? Check your dishwasher's model number (on a label along the door frame or tub edge) against the compatibility list above — the WD15X26078 covers a broad range of GE GDF, GDT, GDP, Profile PDT/PDP, QDP, Monogram ZDT, DDT, and Café CDT series dishwashers. Be aware that some similar-looking GE valves (such as WD15X24213 or WD15X26140) are different parts used on other model groups — they are not interchangeable with the WD15X26078. If your model isn't in the list or your original valve shows a different part number, contact our support team with your model number and we'll verify the correct valve before you order. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same water inlet valve installed in compatible GE, GE Profile, Café, Monogram, Haier, Hotpoint, RCA, and Kenmore GE-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

🚰 DD82-01588A Dishwasher Water Inlet Valve – Genuine OEM Samsung Part 🔁 Replaces These Part Numbers DD82-01588A (primary OEM) Also Replaces PS12593084, AP6807545, DD81-02265A, AP6244375, PS12085633. Description: This Dishwasher Water Inlet Valve Assembly is essential for regulating the water flow into dishwasher, ensuring optimal cleaning performance. This replacement Genuine OEM part is engineered to provide precise water control, preventing leaks and maintaining efficient operation. ✅ Key Features Genuine Samsung OEM part – DD82-01588A Precision-engineered to match factory standards Controls cold water intake with accurate timing and pressure Easy to install using standard tools Tested for leak-free performance 🔧 Fixes Common Symptoms Dishwasher won’t fill or fills slowly Error codes related to water inlet No water intake at cycle start Valve leaks or hums without water flow 🚚 Why Buy from Parts‑O‑Matic? ✅ Genuine OEM quality — not a knock‑off ✅ Always Fast and Free U.S. shipping ✅ Expert customer support for part fitment ✅ Trusted by DIYers and appliance professionals 🛒 Restore proper water fill and cycle reliability — order your DD82-01588A OEM water inlet valve today from Parts‑O‑Matic and enjoy speedy, free delivery.

Read more less

XPARTCO 6501KW2002B Washer Rotor Position Sensor – Compatible with LG and Kenmore Washers Product Description Maintain smooth spin cycles and precise motor control with the XPARTCO 6501KW2002B Washer Rotor Position Sensor. This Sensor Assembly, also known as a hall sensor is a replacement Part and is a vital component in Specific LG, Kenmore washer Models. This part monitors the direction and speed of the spinning rotor. It then communicates this information to the electronic control board. By doing so, it aids in the precise operation of your washer. If your washer pumps but fails to spin or agitate, it may be indicative of a damaged sensor assembly. Replaces Part Numbers 6501KW2002B, 6501KW2002A, AP7015078, PD00073205, EAP16556422, 4962510, PS16556422, EAP16556422. Compatibility This replacement rotor position sensor fits select LG and Kenmore front-load washers. Example compatible models include (but are not limited to): LG WM2487HRM, LG WM0642HW, and Kenmore 796.40272900. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. Key Features Aftermarket Replacement – Designed to match OEM performance and precision Accurate Rotor Feedback – Helps regulate motor speed and direction for smooth washing Cost-Effective Fix – Delivers OEM-level performance at a fraction of the price Plug-and-Play Installation – No wiring modification required Fixes Common Issues – Resolves LE, UE, SE, and spin cycle errors Product Specification Part Number: 6501KW2002B Component Type: Washer Rotor Position Sensor (Hall Sensor) Material: Durable printed circuit board with reinforced plastic housing Mounting: Direct-fit installation on stator assembly Operating Conditions: Rated for high-humidity, high-vibration washer environments Compliance: Built to OEM-equivalent quality standards (not OEM) Installation Notes Tools Needed: 10 mm socket wrench, Phillips screwdriver ⚠️ Safety First: Always unplug the washer before performing repairs to prevent electrical shock. Steps: Disconnect power and remove the rear access panel. Unscrew the rotor bolt and carefully remove the rotor assembly. Locate and unplug the old sensor from the stator. Install the new XPARTCO 6501KW2002B sensor, aligning mounting tabs. Reconnect the wiring harness, reinstall the rotor, and secure the panel. Restore power and run a spin test to verify correct operation. ⏱️ Time Required: 20–25 minutes Shop With Confidence Trusted Appliance Parts Supplier 30-Day Return Policy Restore precise washer performance — Add to Cart Now for a reliable, budget-friendly repair!

Read more less