Search results for "washer water valve"

WP3387747 Genuine OEM Whirlpool Dryer Heating Element The WP3387747 is a Genuine OEM Whirlpool replacement dryer heating element assembly compatible with a wide range of Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, and Magic Chef electric dryers — particularly higher-capacity and newer-generation Duet, Cabrio, HE, and GEW/GEQ series models. The heating element is the primary heat source in an electric dryer — a nickel-chromium resistance coil wound on ceramic insulators inside a steel housing. When the coil burns through, the circuit opens and the dryer produces no heat. When the coil shorts to the housing, the dryer runs too hot or heats continuously after the cycle ends — which is a fire hazard requiring immediate repair. This Genuine OEM part is manufactured by Whirlpool to factory specifications and is rated at 5200W / 240V with two 5/16" male terminals. Note: Whirlpool updated the wattage of this element from the original 5400W down to 5200W — the WP3387747 at 5200W is the correct current OEM replacement for all compatible models. The thermostat and thermal fuse are not included and should be inspected and replaced separately if needed. It directly replaces 3387747, W11344457, W11045584, 80003, 525502, AP6008281, PS11741416, and additional cross-reference numbers. Installs in 20–45 minutes with basic hand tools. Quick Answer The WP3387747 Genuine OEM Whirlpool Dryer Heating Element fixes electric dryers that produce no heat, run too hot, heat continuously, or take too long to dry. 5200W / 240V, nickel-chromium coil, two 5/16" male terminals. Thermostat and thermal fuse not included. Genuine OEM. Replaces 3387747, W11344457, W11045584, 80003, AP6008281, PS11741416. Compatible with Whirlpool Duet/Cabrio/HE/GEW/GEQ, Kenmore, Maytag, Amana, KitchenAid, Roper, Estate, Inglis, and more. Common Problems This Part Fixes Dryer produces no heat at all — element coil burned through Dryer takes much longer than normal to dry clothes Dryer tumbles normally but generates no heat during the cycle Dryer overheating or running hotter than normal — coil shorted to housing Dryer continues to heat after the cycle ends — shorted element (fire hazard) Visible break, burn spot, or sagging coil inside the housing Burning smell during operation — arcing at a weak point in the coil Dryer trips the circuit breaker when the heat cycle is selected Replaces Part Numbers This heating element directly replaces the following OEM and cross-reference part numbers: WP3387747, 3387747, 80003, W11045584, W11344457, PD00002365, EAP11741416, AP6008281, AWP47520, FIX11741416, PS11741416, WP3387747VP. Contact our support team with your model number if you need confirmation before ordering. Compatibility This heating element is compatible with select electric dryers only from the following brands and series: Whirlpool electric dryers — Duet (WED8xxx, WED9xxx), Cabrio (WED7xxx), HE series, GEW9xxx, GEQ9xxx, WED4xxx, WED5xxx and more Kenmore / Sears electric dryers — 110 series and Whirlpool-built models (including Kenmore HE2, HE3, Elite HE4, 90 series) Maytag electric dryers — MEDB, MED series Amana electric dryers KitchenAid electric dryers Roper electric dryers Estate electric dryers Crosley electric dryers Inglis electric dryers Admiral electric dryers Jenn-Air electric dryers Magic Chef electric dryers Note: This is for electric dryers only. Gas dryers use a gas burner and do not have a heating element. Also: do not touch the new element's coil wire with bare hands — skin oils degrade the nickel-chromium wire and significantly shorten element life. Handle by the frame and terminals only. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Primary heat source for electric dryers — nickel-chromium resistance coil generates heat for every drying cycle Rated 5200W / 240V — current OEM wattage (updated from original 5400W by Whirlpool) Two 5/16" male terminals — matches original terminal configuration for direct wire connection Metal and ceramic construction — high-temp terminals and ceramic insulators resist heat fatigue Thermostat and thermal fuse are not included — inspect and replace separately if needed Do not touch the coil wire during installation — skin oils degrade nickel-chromium wire Replaces 3387747, W11344457, W11045584, 80003, AP6008281, and PS11741416 Compatible with Whirlpool Duet, Cabrio, HE, GEW/GEQ series and 11 additional brand platforms DIY repair — installs in 20–45 minutes with basic hand tools Product Specifications Part Number WP3387747 Part Type Dryer Heating Element Assembly (Electric) Condition Genuine OEM Application Electric Dryers Only Wattage 5200W (updated from original 5400W — current OEM spec) Voltage 240V AC Coil Material Nickel-chromium resistance wire Terminals Two 5/16" male terminals Material Metal / Ceramic Color Black / Silver Does Not Include Thermostat or thermal fuse — inspect and replace separately Handling Note Do not touch coil wire — skin oils degrade nickel-chromium wire Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef Installation Notes ⚠️ Unplug Dryer Before Starting — Do Not Touch the Coil Wire Disconnect power before beginning. The heating element housing is accessible from the lower front panel of the dryer on most Duet/Cabrio HE models — remove the front kick panel to access the heater housing without fully disassembling the dryer. For other models, remove the back panel. Before touching the new element, review the wiring layout of the old element so you can reconnect wires to the correct terminals. Do not touch the nickel-chromium coil wire with bare hands at any point — skin oils on the wire cause hot spots that will prematurely burn the element. Handle only by the frame, terminals, and housing. Photograph the existing wiring before disconnecting. Disconnect the element terminal wires and the thermostat and thermal fuse wires. Unscrew the housing and remove the old element. Install the new WP3387747 element, reconnect all wiring in the same positions, reinstall the housing and panels, restore power, and run a test heat cycle. Tools needed: Phillips screwdriver, 1/4" nut driver. Frequently Asked Questions My original element was 5400W but this one is 5200W — is that correct? Yes — Whirlpool intentionally updated the wattage of this heating element from 5400W to 5200W during a design revision. The WP3387747 at 5200W is the current correct OEM replacement for all compatible models that previously used the higher-wattage element. While the wattage is slightly lower, the element is designed to provide equivalent drying performance within the thermal control system of compatible dryers. The updated wattage is by manufacturer design and does not indicate a defect or an incorrect part. How do I test if the heating element has failed? Unplug the dryer and disconnect the element terminals. Set your multimeter to continuity or resistance mode. A working element shows resistance — typically around 9–12 ohms for a 5200W/240V element. An open circuit confirms the coil has burned through. Also test each terminal individually against the metal housing frame — a working element shows no continuity between either terminal and the housing. If continuity exists between a terminal and the housing, the element coil is shorted to ground and must be replaced immediately — do not operate the dryer in this condition. What is the difference between WP3387747 and 279838? Both are Genuine OEM Whirlpool dryer heating elements, but they are for different model generations and are not interchangeable. The 279838 (5400W, 240V) is for standard-capacity Whirlpool-family dryers — many WTW/NED series and standard front-load models. The WP3387747 (5200W, 240V) is for higher-capacity and newer-generation models including Whirlpool Duet, Cabrio, HE, and GEW/GEQ series. Always verify your exact model number to confirm which heating element is correct for your dryer before ordering. Why is it important not to touch the element coil wire? The heating element coil is made of nickel-chromium wire that reaches very high temperatures during operation. Oils from skin contact leave microscopic residue on the wire that creates hot spots when the element heats up — these hot spots cause premature burnout at the contaminated area, often within a few months of installation. Handle the new element by its steel frame, ceramic insulators, and terminals only. If the coil wire is accidentally touched, wipe the contact area with a dry cloth or isopropyl alcohol before installation. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element assembly installed in compatible Whirlpool, Kenmore, Maytag, and related brand electric dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

285785 Washer Transmission Clutch - Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, and Other Washers Product Description Restore your washer’s performance with the replacement 285785 Washer Transmission Clutch. This high-quality replacement clutch assembly, designed for direct-drive (beltless) Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, and other washer models, connects the transmission to the inner tub during the spin cycle and the agitator during the wash cycle. Constructed from durable plastic and metal, this clutch assembly includes a clutch with liner, brake cam driver, retaining clip, blue spring for large capacity (27") washers, and black spring for compact (24") washers. It addresses issues like slow spinning, failure to agitate, burning smells, or excessive shaking. Note: Includes one clutch assembly with hardware. Disconnect power before installation. Replaces part numbers: 285785, 2670, 285331, 285380, 285422, 285540, 285761, 285785VP, 3350015, 3350114, 3350115, 3351342, 3351343, 387888, 388948, 388949, 3946794, 3946847, 3951311, 3951312, 62699, 63174, 63765, 64176, PD00002503, EAP334641, AH334641, EA334641, J27-662, LP326, AP3094537, PS334641. Compatibility: Compatible with models including but not limited to: Whirlpool: WTW5300SQ0, LSR7233EQ0, LSR8433KQ0, LSQ9544KQ0 Kenmore: 110.26902690, 110.28762790, 110.29822800 KitchenAid: KAWS750JQ0, KAWS850JQ0 Maytag: MAV6451AWW, MAV9750AWW Amana: NTW4500XQ0 Roper: RAS8245EQ1, RTW4440XQ0 Inglis: ITW4300SQ0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, Inglis, and other direct-drive washer models. 🔥 Specifications: replacement clutch assembly, plastic and metal, 4-1/2"L x 4-1/2"W x 1-1/8"H, includes clutch w/liner, brake cam driver, retaining clip, blue spring (1.24" for large capacity 27" washers), black spring (1.46" for compact 24" washers). 💰 Cost-Effective Alternative: replacement clutch offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires a socket set, screwdrivers, work gloves; typically installed in 1–2 hours. 🛡️ Reliable Fixes: Resolves slow spinning, failure to agitate, burning smells, excessive shaking, or noisy operation. Installation Notes: Safety First: Disconnect the washer from the power source before installation. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your washer spinning and agitating smoothly today! Add to cart now for a budget-friendly fix!

Read more less

21366 Washer Spanner Nut Replaces WP21366 Replaces Part Numbers: WP21366, 21366, 16060, LP331, AP6005824, PS11738884.

Read more less

5304517203 Genuine OEM Frigidaire Dishwasher Lower Spray Arm The 5304517203 is a genuine Frigidaire OEM lower spray arm for Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers. Positioned at the bottom of the dishwasher tub, this arm rotates as water is pumped through it, spraying water in all directions through its nozzle openings to clean dishes in the lower rack. It snaps directly into the bottom sump assembly and is essential for proper water distribution during the wash cycle. Made of durable plastic and metal, finished in gray/blue. Over time, the arm can crack, warp, or wear from general use and repeated exposure to hot water and detergent — high heat exposure in particular is a documented cause of failure. A broken or worn spray arm typically shows up as visible damage on the arm itself, dishes in the lower rack not getting cleaned properly, reduced or uneven water coverage, or the arm having difficulty rotating or getting stuck. It directly replaces 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623 Quick Answer The 5304517203 Genuine OEM Frigidaire Dishwasher Lower Spray Arm fixes Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers where the lower rack isn't getting cleaned properly, water coverage is reduced or uneven, or the arm won't rotate freely or has visible cracks. Snaps into the bottom sump assembly. Replaces 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623. After installing, confirm the arm spins freely by hand and doesn't contact the heating element before running a cycle. Common Problems This Part Fixes Dishes in the lower rack not getting cleaned properly Reduced or uneven water coverage during the wash cycle Spray arm that won't rotate freely or gets stuck Visible cracks, warping, or damage on the arm itself Arm that has come loose or detached from the sump assembly Clogged nozzle holes reducing water pressure and spray coverage Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher lower spray arm directly replaces the following OEM and cross-reference part numbers: 5304517203, 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lower spray arm is compatible with select Frigidaire dishwashers, and also fits select Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers built on the same platform. Note: Non-genuine versions of this exact part number are sold by several third-party sellers. A customer using a non-genuine version of this spray arm reported it came loose and broke during operation, so confirm you're ordering the genuine Frigidaire part rather than a lower-cost imitation. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified nozzle pattern and rotation fit Snaps directly into the bottom sump assembly for a secure, no-tools installation Resolves "not cleaning lower rack dishes," "uneven water coverage," and "won't rotate freely" symptoms Durable plastic and metal construction, gray/blue finish Approximate dimensions: 16.00" x 3.10" x 3.10" (L x W x H) Direct drop-in replacement — no modification required Replaces 154568001, 5304506526, 154568002, 1542508, 154250801, 154250901, 154281101, 1543358, 154414101, 154414102, 4840174, PD00047210, EAP12585623, AP6783883, AFR18880, PS12585623 Compatible with Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, and Kenmore dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 5304517203 Part Type Dishwasher Lower Spray Arm Condition Genuine OEM Brand Frigidaire Location Bottom of the dishwasher tub, in the lower sump assembly Material Plastic and metal Color Gray / Blue Dimensions Approx. 16.00" x 3.10" x 3.10" (L x W x H) Repair Difficulty Very Easy — no tools required Quantity 1 lower spray arm Compatible Brands Frigidaire, Electrolux, Gibson, Crosley, Kelvinator, Westinghouse, Kenmore Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — Confirm Clearance From The Heating Element Disconnect power to the dishwasher and shut off the water supply before beginning. Wear work gloves. Open the dishwasher and pull out the lower rack, setting it aside. Remove the old lower spray arm by releasing the locking tabs on each side and gently pulling it off the sump assembly. Snap the new 5304517203 spray arm onto the sump assembly in the same position. Before closing everything up, spin the arm gently by hand to confirm it rotates freely and does not make contact with the heating element — a real customer account described a spray arm and its support becoming loose and falling into the tub during use, so it's worth double-checking that the arm is fully and securely seated before running a cycle. Return the lower dish rack to its position and close the dishwasher door. Restore power and water, then run a test cycle to confirm the arm spins smoothly and dishes in the lower rack are getting properly cleaned. Tools needed: none. Frequently Asked Questions My dishes in the lower rack aren't getting clean. Is this the part I need? Yes, this is one of the most common symptoms of a worn or damaged lower spray arm. If the arm is cracked, clogged, or not rotating freely, water can't reach dishes in the lower rack evenly, leaving them dirty even when the upper rack comes out clean. I've read that a spray arm can come loose during operation. How do I prevent that? This has been reported, particularly with non-genuine imitation parts under the same number. To help prevent it, make sure the new arm snaps fully and securely onto the sump assembly during installation, and spin it gently by hand to confirm it's seated correctly and rotates without wobbling before running your first cycle with it installed. Do I need any tools to replace this spray arm? No. This is a simple snap-in, snap-out repair — release the locking tabs on the old arm to remove it, and press the new one onto the sump assembly until it clicks into place. No tools are required. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original nozzle pattern, dimensions, and sump connection of the lower spray arm originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 131763310 Washer Door Striker The XPARTCO 131763310 is an aftermarket replacement door striker (also called a door strike or door catch) compatible with select Frigidaire, Kenmore, Electrolux, Crosley, Gibson, White-Westinghouse, Kelvinator, and Tappan front-load washers. The door striker is a small plastic tab mounted on the washer door that engages with the door lock assembly on the front of the washer when the door is closed — activating the door switch and allowing the washer to start, fill, and spin. When the striker breaks or wears down, the door will not properly activate the door lock, causing the washer not to start, not to fill, or to display a door-related error code. Made from durable white plastic, this striker measures approximately 1-1/4" L x 9/16" W x 2-9/16" H with approximately 2 inches between mounting holes (center to center). It directly replaces 131763300, 134456600, 1032664, LP3310, AP3580441, and several additional cross-reference numbers. Sold individually. Installs in under 15 minutes with a Phillips screwdriver. Quick Answer The XPARTCO 131763310 Washer Door Striker fixes Frigidaire-platform front-load washers where the door won't activate the door lock, the washer won't start, won't fill, leaks from the door, or shows a door-related error code. White plastic, approx. 1-1/4" L x 9/16" W x 2-9/16" H, ~2" between mounting holes. Sold individually. Phillips screwdriver only — installs in under 15 minutes. Compatible with Frigidaire, Kenmore, Electrolux, Crosley, Gibson, and more. Common Problems This Part Fixes Washer door will not properly latch or activate the door lock when closed Washer will not start — door switch not being triggered by the striker Washer will not fill with water — door lock not engaged Washer will not spin — door lock fault preventing cycle completion Water leaking from the door area due to door not sealing properly Door-related error codes displayed on compatible models Broken, cracked, or missing door striker visible on the washer door Replaces Part Numbers This door striker directly replaces the following OEM and cross-reference part numbers: 131763310, 134456600, 131763302, 1032664, 131763300, AH890617, EA890617, AP3580441, PS890617, AFR14210, PD00000391, EAP2378364, AP4508273, PS2378364, WH10X10004, 824421, AH269392, EA269392, AP2621447, PS269392. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door striker is compatible with select front-load washers from the following brands: Frigidaire front-load washers (ATF, ATFB, BLTF, GLTF, LTF, FTF, FAFW, FRFW series and more) Kenmore / Sears front-load washers (select Frigidaire-built models) Electrolux front-load washers (select models) Crosley front-load washers (CFW, CLCE series) Gibson front-load washers (GTF series) White-Westinghouse front-load washers Kelvinator front-load washers Tappan front-load washers Note: The 131763310 (white) and 131763302 (gray) are interchangeable and functionally identical — the only difference is color. Either part will work as a replacement regardless of which color was originally installed. Key Features Engages with the door lock assembly to activate the door switch, allowing the washer to start, fill, and run Critical safety component — washer will not operate without a properly functioning door striker Durable white plastic construction — strong and wear-resistant for long service life Dimensions: approx. 1-1/4" L x 9/16" W x 2-9/16" H; ~2" between mounting holes (center to center) Sold individually — one striker per order Direct replacement for 131763300, 134456600, 1032664, and LP3310 Compatible with Frigidaire, Kenmore, Electrolux, Crosley, Gibson, White-Westinghouse, Kelvinator, and Tappan washers Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in under 15 minutes with a Phillips screwdriver only Product Specifications Part Number 131763310 Part Type Washer Door Striker (Door Strike / Door Catch) Condition Aftermarket Replacement Application Front-Load Washers Dimensions Approx. 1-1/4" L x 9/16" W x 2-9/16" H Mounting Hole Spacing Approx. 2" center to center Color White Material Plastic Sold As Single striker Compatible Brands Frigidaire, Kenmore, Electrolux, Crosley, Gibson, White-Westinghouse, Kelvinator, Tappan Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power before beginning any repair. Open the washer door and locate the door striker — it is the small plastic tab mounted on the inside of the door, typically near the top or center of the door panel. Remove the two Phillips screws securing the old striker to the door. If the striker is broken, the screws may already be loose or missing. Align the new 131763310 striker with the mounting holes in the door and secure it with the two Phillips screws. Close the door to confirm it clicks firmly into the door lock assembly. Restore power and run a short cycle to verify the washer starts, fills, and runs normally. Tools needed: Phillips screwdriver only. Frequently Asked Questions What does the washer door striker do? The door striker is the small plastic tab on the washer door that engages with the door lock assembly mounted on the front of the washer when the door is closed. As the door closes, the striker pushes into the door lock, activating the door switch — a signal to the control board that the door is securely closed. The washer will not start, fill, or spin unless the door switch is activated by the striker. A broken or worn striker means the door lock is never properly engaged, so the washer appears to be in a constant "door open" state even when the door is physically shut. What is the difference between the 131763310 and 131763302 door strikers? Both are Frigidaire-platform door strikers, they are different color and interchangeable. The 131763310 is used on older Frigidaire front-load washer models (ATF, GLTF, FAFW series and others). The 131763302 is a gray color used on newer Frigidaire and Electrolux models. Always compare your existing striker's shape and dimensions to confirm, or contact our support team with your model number. Should I also replace the door lock assembly when replacing the striker? Not necessarily — in most cases the striker is the only part that needs replacement. The striker is a small plastic tab that takes repeated impact every time the door is closed, making it the most commonly worn part in the door latch system. The door lock assembly (131763202) is more durable and less prone to failure. Inspect the door lock for any cracks, burn marks, or a latch that does not spring back after pressing — if it appears damaged, replace it as well. If the lock looks intact, the 131763310 striker alone should resolve the issue. My washer door closes but the washer still won't start — is it the striker? It may be. If the striker is cracked, worn, or broken, it may appear to engage the door lock but not push far enough into the lock assembly to fully activate the door switch. In other cases, a fully intact striker may not be the cause — the door lock assembly itself (131763202) or the door latch on the frame side may also be the culprit. Visually inspect the striker first — if it is visibly broken, replace it. If it appears intact, the issue may be with the door lock assembly or wiring. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire OEM part, but is manufactured from durable plastic to match the dimensions and function of the original 131763310 door striker. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

4392067 Genuine OEM Whirlpool Dryer Repair Kit — Belt, Rollers & Idler (27") The 4392067 is a Genuine OEM Whirlpool dryer maintenance and repair kit that contains all the components most commonly replaced when a 27-inch Whirlpool-family dryer becomes noisy, stops tumbling, or starts vibrating — specifically the drum drive belt, all four drum support rollers, the idler pulley, tri-ring retaining clips, a washer, and installation instructions. Installing all of these components together in a single repair restores smooth, quiet drum rotation and eliminates the most common causes of dryer noise and drum drive failure in one visit. As a Genuine OEM kit assembled by Whirlpool to factory specifications, the 4392067 includes the belt (661570V), four rollers (WPW10314173), idler pulley (279640), nine tri-rings, one washer, and instructions. Compatible with 27-inch Whirlpool, Kenmore 110-series, Maytag, Roper, Estate, Crosley, Amana, and Admiral dryers built in 1965 or later. Important: the included belt (661570V, 93-1/2" x 1/4", 4-rib) is correct for many models but does not fit all — verify that 661570V is the correct belt for your specific model before ordering. It directly replaces AP3109602, 2015, 4392067VP, 587637, 80047, AH373088, EA373088, EAP373088, and PS373088. Installs in 45–60 minutes with basic hand tools. Quick Answer The 4392067 Genuine OEM Whirlpool Dryer Repair Kit fixes 27-inch Whirlpool-family dryers that are squealing, thumping, rumbling, or where the drum has stopped spinning. All-in-one kit: belt 661570V + 4 rollers (WPW10314173) + idler pulley (279640) + 9 tri-rings + washer + instructions. Genuine OEM. Important: belt 661570V fits many but not all models — verify your belt part number before ordering. Replaces AP3109602, 2015, 4392067VP, 587637, PS373088. Common Problems This Kit Fixes Loud squealing, squeaking, or thumping noise during the drying cycle Rumbling or grinding noise — worn drum support rollers Drum not spinning — broken or stretched drive belt Motor running but drum still — belt has snapped Belt repeatedly slipping — worn idler pulley no longer maintaining belt tension Burning rubber smell — slipping belt from a failed idler pulley Extended drying times — drum not rotating at correct speed due to belt or roller wear Excessive vibration during the drying cycle What's in the Kit Part 1 Drum Drive Belt — 661570V 93-1/2" long x 1/4" wide · 4-rib profile · Wraps around the drum and connects to the motor pulley and idler pulley to spin the drum · Important: 661570V is correct for many but not all compatible models — verify this belt number fits your specific dryer before ordering Parts 2–5 (qty: 4) Drum Support Rollers — WPW10314173 (set of 4) Cylindrical rubber-and-plastic wheels that support the drum rim as it rotates · LG/Whirlpool 27" dryer platform · Replace all 4 at the same time for even drum support Part 6 Idler Pulley Assembly — 279640 Spring-tensioned pulley wheel that presses against the drive belt to maintain correct belt tension · Pulley wheel only (not the arm) — mounts on the existing idler arm inside the dryer Hardware 9 Tri-Ring Retaining Clips + 1 Washer + Instructions Tri-ring clips secure the drum rollers to their mounting shafts · Washer provides proper spacing at roller shaft · Instruction sheet included Replaces Part Numbers This dryer repair kit directly replaces the following OEM and cross-reference part numbers: 661570V, 279640, WPW10314173, 8536974, 4392067, 2015, 4392067VP, 587637, 80047, AH373088, EA373088, AWP39353, EAP373088, PD00002451, AP3109602, PS373088. Contact our support team with your model number if you need confirmation before ordering. Compatibility This repair kit is compatible with 27-inch gas and electric dryers from the following brands (built 1965 or later): Whirlpool dryers (27" WED, WGD, Cabrio, Duet, and related series) Kenmore / Sears dryers — 110-series (Whirlpool-built models) Maytag dryers (Bravos XL and related series) Roper dryers Estate dryers Crosley dryers Admiral dryers Amana dryers (select models) Important — Belt Compatibility: The belt included in this kit is part number 661570V (93-1/2" x 1/4", 4-rib). This belt is correct for many 27-inch Whirlpool-family dryers but does not fit all compatible models. Before ordering, verify that 661570V is the correct belt part number for your specific dryer model. If your dryer uses a different belt, the rollers and idler pulley in this kit will still fit, but you will need to order the correct belt separately. Key Features Genuine OEM kit assembled by Whirlpool — all components manufactured to factory specifications All-in-one repair: belt (661570V) + 4 rollers (WPW10314173) + idler pulley (279640) + tri-rings + washer + instructions in a single box Replaces all the most commonly worn drum drive components in a single repair — eliminates the need for separate part orders and multiple teardowns For 27-inch Whirlpool-family dryers built 1965 or later Belt 661570V: 93-1/2" long x 1/4" wide, 4-rib — verify fit for your model before ordering Idler pulley (279640) is the pulley wheel only — mounts on the existing idler arm Compatible with Whirlpool, Kenmore 110-series, Maytag, Roper, Estate, Crosley, Admiral, and Amana Installs in 45–60 minutes with basic hand tools Product Specifications Kit Part Number 4392067 Condition Genuine OEM Application 27-inch Gas and Electric Dryers (built 1965 or later) Belt Included 661570V — 93-1/2"L x 1/4"W, 4-rib (verify fit for your model) Rollers Included 4x WPW10314173 drum support rollers Idler Pulley Included 279640 (pulley wheel only — not the arm) Hardware Included 9 tri-ring retaining clips, 1 washer, instructions Compatible Brands Whirlpool, Kenmore, Maytag, Roper, Estate, Crosley, Admiral, Amana Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the top panel by inserting a putty knife under the front edge to release the spring clips, then lift. Remove the front panel to fully expose the drum. Take a photo of the existing belt routing before removing anything. Release the drive belt from the idler pulley and slide it off the drum. Remove the drum and set it aside. Replace all four drum support rollers — remove the old tri-ring clips with needle-nose pliers, slide the old rollers off the shafts, and install the new WPW10314173 rollers with new tri-rings and the included washer. Replace the idler pulley (279640) by pressing the new wheel onto the idler arm shaft. Route the new 661570V belt around the drum (ribbed side against the drum), under the idler pulley, and around the motor pulley. Reinstall the drum, front panel, and top panel. Restore power and run a test cycle. Tools needed: Phillips screwdriver, putty knife, needle-nose pliers, socket set. Frequently Asked Questions How do I know if the belt in this kit (661570V) fits my dryer? The belt included in this kit is 661570V (93-1/2" long, 1/4" wide, 4-rib). To confirm it is correct for your dryer, look up your dryer's model number in an online parts diagram and check the belt part number listed. If the parts diagram shows 661570V or its cross-reference 661570, this kit's belt is correct. If your diagram shows a different belt part number — for example 341241, W10205415, or WP8547157 — the rollers and idler in this kit will still fit your dryer, but you will need to order the correct belt separately. This is the most important compatibility check before purchasing this kit. Is the idler pulley (279640) a complete arm assembly or just the wheel? The 279640 included in this kit is the pulley wheel only — it does not include the idler arm or bracket. It presses onto the existing idler arm shaft inside your dryer. If the idler arm itself is cracked or broken, the arm assembly will need to be replaced separately. On most Whirlpool 27-inch dryers the arm itself rarely fails — it is the wheel bearing that wears out, which is what the 279640 wheel in this kit addresses. Why should I replace all four rollers instead of just the one that's noisy? All four drum support rollers wear at the same rate through the same number of drying cycles. When one roller starts making noise, the other three have experienced the same wear and are likely close behind. Replacing only the noisy roller leaves three worn rollers supporting the drum unevenly, often leading to a repeat repair within months. Since the dryer is already fully disassembled for this repair, replacing all four at once is the most cost-effective and long-lasting approach. How is the 4392067 kit different from the 4392065 kit? Both are Genuine OEM Whirlpool dryer repair kits but for different dryer platforms. The 4392065 is for older Whirlpool 29-inch dryers with the lint screen on top (contains belt 341241, 2 rollers 349241T, idler pulley 691366). The 4392067 is for newer Whirlpool 27-inch dryers with the lint screen inside the door — typically the Duet, Cabrio, Bravos XL, and Thin Twin platforms (contains belt 661570V, 4 rollers WPW10314173, idler pulley wheel 279640). They are not interchangeable — verify your dryer's lint filter location and model series before ordering. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM kit assembled by Whirlpool to factory specifications. All components — belt, rollers, idler pulley, tri-rings, and washer — are the same parts installed in compatible Whirlpool, Kenmore, Maytag, and related brand 27-inch dryers from the factory. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO Dryer Repair Set XPARTCO EXP526 Dryer Belt and Idler Pulley Set 2-piece drum drive repair set replacing 661570V and W10837240 on compatible Whirlpool-built dryers. Product Overview The XPARTCO EXP526 Dryer Belt and Idler Pulley Set combines two common dryer drive-system wear parts in one repair package: a drum drive belt and a complete idler pulley assembly with arm/bracket. The belt transfers motor power to the dryer drum, while the idler assembly maintains the proper belt tension needed for smooth drum rotation. Quick Answer EXP526 includes 2 pieces: one 661570V-style drum belt and one W10837240-style idler pulley assembly. The belt is approximately 93-1/2 inches long, 1/4 inch wide, with 4 ribs and 3 grooves. Common Problems This Kit May Fix Dryer drum will not turn Broken or stretched drum belt Squealing or chirping from the idler area Intermittent drum rotation Belt slipping or running loose Worn or seized idler pulley Replaces and Cross-References WP40111201, 40111201, 14218936, 40051501, 40051502, 59174, PD00002505, EAP11742271, AP6009126, PS11742271, R0606549, WP40111201VP, 661570V, 661570, 3387610, 3389728, 3393999, 339728, 661570VP, PD00023608, AP5983729, PS11722115, W10837240, W10547287, W10547290, 3387372, 3388674, W10118754, W10118756, W10837240VP, PD00025564, FIX11726337, AP5988716, PS11726337, 279640, AP3094197, 279640VP, 2958, 3388672, 697692, TJ279640, W10468057, AH334244, EA334244, ER279640, PS334244 Cross-reference numbers are provided for identification. XPARTCO is an aftermarket replacement brand and is not manufactured by Whirlpool Corporation. Compatibility Fits select Whirlpool-built dryers using both the 661570V belt and W10837240 idler assembly. Verified examples include: WED8300SW0 MEDB750YW0 NED7300WW1 110.C87571601 110.C87566601 110.C96562500 Important: This is only a partial model list. Some similar dryers use a different belt or idler design. Verify the complete dryer model number and original part numbers before ordering. Key Features Complete 2-piece drive repair set Includes drum belt and idler pulley assembly Idler includes pulley wheel, arm/bracket and axle Helps restore proper drum rotation and belt tension Quality XPARTCO aftermarket replacement Product Specifications Kit Number EXP526 Brand XPARTCO Kit Contents 1 Drum Belt + 1 Idler Pulley Assembly Belt Reference 661570V Belt Length Approx. 93-1/2 in. Belt Width Approx. 1/4 in. Belt Rib/Groove 4 Ribs / 3 Grooves Idler Reference W10837240 Idler Type Complete Pulley with Arm/Bracket Condition New Aftermarket Replacement Installation Notes Disconnect the dryer from electrical power before service. Shut off the gas supply on gas dryers. Access the drum drive system according to the appliance service procedure. Note the original belt routing around the motor pulley and idler before removal. Install the idler assembly securely and confirm the pulley rotates freely. Install the new belt with the ribbed side against the drum and motor pulley. Route the belt through the idler correctly so proper tension is applied. Rotate the drum by hand before reassembly to confirm smooth belt tracking. Diagnostic tip: If a belt failed prematurely, inspect the drum rollers, motor pulley, drum alignment, and idler system before returning the dryer to service. FAQ What is included in EXP526? One 661570V-style drum drive belt and one W10837240-style complete idler pulley assembly. How many ribs does the belt have? The 661570V-style belt has 4 ribs and 3 grooves and is approximately 93-1/2 inches long. Is this a Genuine Whirlpool OEM kit? No. EXP526 is a quality XPARTCO aftermarket replacement set designed to replace the listed OEM part numbers. Will it fit every Whirlpool dryer? No. Whirlpool-built dryers use multiple belt and idler designs. Verify your complete model number and the original belt/idler part numbers before ordering. Shop With Confidence Confirm your dryer model number before ordering. Compatibility support is available to help verify the correct belt and idler combination. XPARTCO Replacement2-Piece Drive KitCompatibility SupportFast U.S. Shipping

Read more less

XPARTCO 12138200000320 Dryer Door Catch The XPARTCO 12138200000320 is an aftermarket replacement dryer door catch compatible with select Midea and Insignia dryers. The door catch is a small plastic spring-clip mechanism mounted on the dryer door that snaps over the door strike o12138200000320 n the cabinet opening to hold the door firmly closed during operation. When the door is closed and latched, the door switch is activated — signaling the control board that it is safe to run. When the catch breaks, cracks, or loses its spring tension, the door will not stay closed, the door switch will not activate properly, and the dryer will either not start or will stop mid-cycle. This is a snap-in replacement catch — the color or exact finish may vary by production run. It directly replaces AP7152622 and PS18161385. Sold individually. Installs in under 5 minutes — no tools required in most cases. Quick Answer The XPARTCO 12138200000320 Dryer Door Catch fixes Midea and Insignia dryers where the door won't stay closed, pops open during a cycle, or where the dryer won't start because the door switch isn't being activated. Snap-in installation — no tools required, installs in under 5 minutes. Sold individually. Replaces AP7152622, PS18161385. Common Problems This Part Fixes Dryer door will not stay closed during the drying cycle Door pops open mid-cycle, stopping the dryer Dryer will not start — door switch not being activated by a worn or broken catch Door feels loose or does not click shut firmly when closed Door catch visibly cracked, broken, or missing Dryer requires the door to be held or pushed to stay running Replaces Part Numbers This door catch directly replaces the following part numbers: 12138200000320, AP7152622, PS18161385. Contact our support team with your model number if you need confirmation before ordering. Compatibility This door catch is compatible with select dryers from the following brands: Midea dryers (gas and electric — select models) Insignia dryers (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Holds the dryer door closed and activates the door switch so the dryer can run safely Snap-in installation — no tools required in most cases; installs in under 5 minutes Durable plastic construction — designed to withstand repeated opening and closing Sold individually — one door catch per order Replaces AP7152622 and PS18161385 Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 12138200000320 Part Type Dryer Door Catch (Door Latch Clip) Condition Aftermarket Replacement Application Gas and Electric Dryers Material Plastic Installation Snap-in — no tools required Sold As Single door catch Compatible Brands Midea, Insignia Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power before beginning. Open the dryer door and locate the old door catch — it is a small plastic clip mounted on the inside of the door or on the cabinet opening around the door. Press the tabs on the old catch to release it from its mounting slot and pull it free. Note the orientation before removing. Insert the new 12138200000320 catch into the slot in the same orientation and press firmly until it snaps into place. Close the door to confirm it latches securely. Restore power and run a short cycle to verify the door stays closed and the dryer operates normally. Tools needed: None in most cases; a small flat-head screwdriver may help with removal. Frequently Asked Questions What dryers is the 12138200000320 compatible with? The 12138200000320 door catch is used on select Midea and Insignia dryer models. Insignia is a Best Buy house brand whose appliances are manufactured by Midea. Always verify your exact model number before ordering to confirm this catch fits your dryer's door latch assembly. Why won't my dryer start even though I'm closing the door? If the door catch is broken or worn, the door may not be engaging the door switch firmly enough to signal the control board that the door is closed. Most dryers will not run unless the door switch is fully activated. Replacing the 12138200000320 catch restores the firm snap needed to trigger the switch. If replacing the catch does not resolve the start issue, the door switch itself may also need to be checked. Do I need to replace the door strike as well? Not necessarily. In most cases only the door catch (the spring-clip on the door) needs replacement. The door strike (the post or tab on the cabinet that the catch snaps onto) is typically more durable. Inspect the strike for cracks or breakage before ordering — if it is intact, just the 12138200000320 catch is all you need. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Midea OEM part, but is manufactured from durable plastic to match the dimensions and function of the original 12138200000320 door catch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 341241 Dryer Drum Belt The XPARTCO 341241 is an aftermarket replacement dryer drum belt compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, and Ikea. The drum belt wraps around the outside of the dryer drum, loops around the motor pulley and idler pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from high-strength rubber with reinforced ribs, this belt measures 92-1/4 inches long x 1/4 inch wide and features 4 ribs and 3 grooves. It is flat on one side and ribbed on the other, and is built to resist cracking, stretching, and wear under the high heat and repeated tension cycles of daily dryer use. It also replaces some 5-rib, 4-groove belts. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 341241 Dryer Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is coming from the dryer. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, and more. Measures 92-1/4" L x 1/4" W with 4 ribs and 3 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Burning rubber smell coming from the dryer Visible broken or frayed belt pieces found inside the dryer cabinet Clothes taking too long to dry due to drum not rotating at correct speed Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: 341241, 14210003, 2008, 26000341241, 26000349533, 31001026, 31531589, 3389628, 3392665, 3394651, 3399844, 341241VP, 345473, 349533, 529597, 53-0186, 53-1080, 53-1086, 53-1528, 53-1589, 53-2671, 53-2910, 660996, 660997, 661561, 693306, 694088, 694416, 694868, 695055, 697388, 8066065, 8206, 8210, 920H4, 920H5, 99906951, 99989673, 99989674, FSP341241, LB276, LB279, P46-037, P46-149, W10127457, W10131364, AH346995, AP32, EA346995, ER341241, AWP39161, PD00002263, EAP346995, 694088-NC, AP2946843, PS346995, TJ341241. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (select models) Maytag dryers KitchenAid dryers Amana dryers Roper dryers Admiral dryers Jenn-Air dryers Estate dryers Magic Chef dryers Crosley dryers Inglis dryers Norge, Modern Maid, Hardwick, Caloric, and Ikea dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the motor pulley and idler pulley for smooth, consistent tumbling every cycle 92-1/4" length x 1/4" width — 4-rib, 3-groove design; flat on one side, ribbed on the other Also replaces some 5-rib, 4-groove belts — wide cross-compatibility across Whirlpool-family models Made from high-strength rubber with reinforced ribs — resists cracking, stretching, and heat damage Direct replacement for OEM part numbers 341241 and 8066065 — no modification required Compatible with over a dozen major appliance brands built on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — installs in 30–45 minutes with basic hand tools Often replaced together with the idler pulley (691366) and drum rollers (349241T) for a complete drum drive repair Product Specifications Part Number 341241 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Gas and Electric Dryers Length 92-1/4 inches Width 1/4 inch Ribs 4 ribs, 3 grooves Profile Flat on one side, ribbed on the other Material High-strength rubber with reinforced ribs Color Black Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, Ikea Often Replaced With 691366 Idler Pulley, 349241T Drum Rollers Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen, then unscrew the two Phillips screws inside the lint filter housing. Use a putty knife 2 inches from each front corner to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release belt tension at the idler pulley, lift the drum slightly, and slide the old belt off. Loop the new 341241 belt around the drum with the ribbed side facing down (toward the drum). Route the belt around the idler pulley and motor pulley — consult your model's service manual or a model-specific video for the correct belt path. Reassemble and run a test cycle. Tip: While the drum is out, inspect and replace the idler pulley (691366) and drum rollers (349241T) if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions How does the 341241 differ from the W10205415 and 6602-001655 belts? All three are 92-inch dryer drum belts, but they differ in width and rib count. The 341241 is 1/4" wide with 4 ribs and 3 grooves. The W10205415 is 3/8" wide with 5 ribs and 4 grooves. The 6602-001655 is 5/16" wide with 5 ribs and 4 grooves designed for Samsung dryers. Always match the part number to your specific model — do not substitute based on appearance alone. Will this belt fit my Kenmore dryer? Many Kenmore dryers — especially the popular 110-series — are manufactured by Whirlpool and use the 341241 belt. Check your model number against the compatibility list and contact our support team if you need help confirming the fit before ordering. How do I know if my drum belt needs to be replaced? The most obvious sign is that the dryer motor hums but the drum does not spin. You may also notice a thumping or slapping sound during operation, a burning rubber smell, or clothes that are damp after a full cycle. Open the dryer cabinet to visually confirm if the belt is broken, frayed, or stretched. Should I also replace the idler pulley and drum rollers? Yes — since the dryer is already disassembled, it is highly recommended to inspect and replace the idler pulley (691366) and drum support rollers (349241T) at the same time. These parts wear at a similar rate and replacing all three together — often sold as a repair kit — prevents having to disassemble the dryer again in the near future. Is this an OEM or aftermarket part? This is an aftermarket replacement built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is made from high-strength rubber to match the dimensions and performance of the original 341241 belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO 3977393 Dryer Thermal Cut Off (309°F) – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Protect your dryer from overheating with the XPARTCO 3977393 Dryer Thermal Cut Off (309°F). This high-quality aftermarket replacement is a critical safety component designed to permanently interrupt power to the heating circuit if temperatures exceed 309°F (154°C). A blown thermal cut off can result in no heat. Replacing it with this reliable XPARTCO component helps restore safe operation and prevent further damage to heating elements or internal components. XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and performance. Replaces Part Numbers 3977393, AP3094244, PS334299, EAP334299 Compatibility This replacement dryer thermal cut off fits select Whirlpool, Maytag, Kenmore (Whirlpool-manufactured), Amana, Estate, and Roper dryers. Commonly installed on the heater housing assembly. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature rating and fit 🌡️ 309°F (154°C) Cut-Off Rating – Designed for high-heat safety protection 🛡️ Prevents Overheating Damage – Protects heating element and dryer components 🧩 Direct-Fit Design – Installs easily without modification 💰 Cost-Effective Repair – Affordable alternative to OEM thermal cut offs 📐 Product Specification Part Number: 3977393 Component Type: Dryer Thermal Cut Off Temperature Rating: 309°F (154°C) Function: One-time over-temperature safety cutoff Mounting: Screw-mounted Application: Dryer heater housing assembly Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Unplug the dryer before servicing to avoid electrical shock. Basic Steps: Disconnect dryer power. Remove rear panel to access heater housing. Locate and disconnect the old thermal cut off. Remove mounting screws and install the new XPARTCO 3977393 cut off. Reconnect wiring and reassemble the dryer. Restore power and test operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore dryer safety and prevent overheating — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

W11497943 Dishwasher Genuine Drain Pump Motor Replaces Part Numbers: W11497943, AP6994646, PS16221213, W11412663.   Description: This Drain Pump Motor is a Genuine OEM component for select Maytag, Kenmore, Whirlpool dishwasher models. This electric motor powers the drain pump to empty wash water from the tub at the end of cycles. Common causes of a bad pump motor include wear over extended use, moisture damage degrading electronics, or electrical faults from voltage fluctuations.

Read more less

XPARTCO W10734521 Washer Clutch Slider Kit The XPARTCO W10734521 is an aftermarket replacement washer clutch slider kit compatible with a wide range of Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Crosley, Estate, Jenn-Air, Roper, Magic Chef, Admiral, and Kirkland HE top-load washers. The clutch slider kit is part of the drive system that engages and disengages the inner tub from the gearcase — it's responsible for transitioning the washer between agitation and spin modes. The slider gear works together with the electromagnetic clutch and gearcase to move the inner tub during the wash and spin portions of every cycle. When the slider or its spring fails, the washer typically won't spin properly, won't agitate, makes grinding noise, or leaves clothes soaking wet at the end of a cycle. This kit includes the slider, spring support, 30mm spiral, and bolt. Slider dimensions: 2-7/8" outer diameter x 7/8" deep. Support spring: 1-5/8" outer diameter x 1-1/8" long. Spiral: 1-5/16" outer diameter. Bolt: 7/8" head diameter x 1" high. Construction is metal and plastic in black, white, and gray. Important: this is the slider kit only — it does NOT include the electromagnetic clutch (sold separately as W10754448). The current W10734521 part number supersedes the earlier W10006484, W10006494, W10275082, W10447975, and W10905025. It also replaces 3452506, AP5952873, EAP10060062, PD00025495, and PS10060062. Installs in 60–90 minutes with basic hand tools. Quick Answer The XPARTCO W10734521 Washer Clutch Slider Kit fixes Whirlpool, Maytag, Kenmore, KitchenAid, and related HE top-load washers that won't spin or agitate properly, won't transition between cycle phases, leave clothes soaking wet, or make grinding noise during the spin cycle. Slider kit only — electromagnetic clutch (W10754448) is sold separately. Includes slider (2-7/8" OD), spring support (1-5/8" OD), 30mm spiral, and bolt. Replaces W10006484, W10006494, W10275082, W10447975, W10905025, 3452506, AP5952873, EAP10060062, PD00025495, PS10060062. Common Problems This Part Fixes Washer won't spin or spins very slowly — slider not engaging the gearcase for spin mode Washer won't agitate — slider not transitioning the drive system to agitation mode Clothes left soaking wet at the end of the cycle — incomplete spin Grinding, rattling, or clunking noise during the spin or agitation phase Washer fills and drains normally but never spins or agitates Worn or broken slider gear teeth visible on the drive assembly Weak or broken slider spring — washer drive losing positive engagement Repeated cycle interruptions in the spin or agitation portion of cycles What's in the Kit Part 1 Slider Gear 2-7/8" outer diameter x 7/8" deep · Slides over the drive assembly shaft to engage/disengage the gearcase for agitation and spin transitions · Install with the teeth facing outward Part 2 Spring Support 1-5/8" outer diameter x 1-1/8" long · Provides return tension for the slider · Replace whenever the gearcase or slider is replaced — spring can weaken over time Part 3 30mm Spiral 1-5/16" outer diameter · Spiral retaining component that holds the slider assembly together on the drive shaft Part 4 Bolt 7/8" head diameter x 1" high · Secures the assembly Replaces Part Numbers This clutch slider kit directly replaces the following OEM and cross-reference part numbers: W10734521, 3452506, W10006484, W10006494, W10275082, W10447975, AP5952873, AWP41487, EAP10060062, PD00025495, PS10060062. W10734521 is the current production part superseding W10006484, W10006494, W10275082, W10447975, and W10905025. Contact our support team with your model number if you need confirmation before ordering. Compatibility This clutch slider kit is compatible with select HE top-load washers from the following brands: Whirlpool top-load washers (Cabrio, WTW5000, WTW5500, WTW5700, WTW6000, WTW6200, WTW6400, WTW7000, WTW7120, WTW8000, WTW8200, WTW8500, WTW8700 series and related models) Maytag top-load washers (Bravos and Centennial series and related models) Kenmore / Sears top-load washers (Whirlpool-built — select 110-series and related models) KitchenAid top-load washers (select models) Amana top-load washers (select models) Crosley top-load washers (select models) Estate top-load washers (select models) Jenn-Air top-load washers (select models) Roper top-load washers (select models) Magic Chef top-load washers (select models) Admiral top-load washers (select models) Kirkland top-load washers (select models) Important — Slider Kit Only, NOT Clutch: This is the clutch slider kit (slider, spring, spiral, bolt) — it does not include the electromagnetic clutch assembly. The electromagnetic clutch is part number W10754448 and is sold separately. If you need both components, order each part separately. Many repair scenarios call for replacing both at the same time, since both wear together. Always verify your model number and confirm exactly which component has failed before ordering. Key Features Complete slider repair kit — slider, spring support, 30mm spiral, and bolt included as a matched set Works with the electromagnetic clutch and gearcase to drive the inner tub during agitation and spin modes Resolves "won't spin," "won't agitate," and "clothes left soaking wet" symptoms when the slider has worn or the spring has weakened Current production part number — supersedes W10006484, W10006494, W10275082, W10447975, and W10905025 Slider: 2-7/8" outer diameter x 7/8" deep · Spring: 1-5/8" OD x 1-1/8"L · Spiral: 1-5/16" OD · Bolt: 7/8" head x 1"H Metal and plastic construction in black, white, and gray Important: slider kit only — electromagnetic clutch (W10754448) sold separately For full performance, replace all components in the kit together as a set Compatible with Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Crosley, Estate, Jenn-Air, Roper, Magic Chef, Admiral, and Kirkland HE top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 60–90 minutes with basic hand tools Product Specifications Part Number W10734521 Supersedes W10006484, W10006494, W10275082, W10447975, W10905025 Part Type Washer Clutch Slider Kit Condition Aftermarket Replacement Application HE Top-Load Washers (Whirlpool platform) Includes 1x Slider, 1x Spring Support, 1x 30mm Spiral, 1x Bolt Slider Dimensions 2-7/8" Outer Diameter x 7/8" Deep Spring Support Dimensions 1-5/8" Outer Diameter x 1-1/8" Long Spiral Dimensions 1-5/16" Outer Diameter Bolt Dimensions 7/8" Head Diameter x 1" High Material Metal / Plastic Color Black / White / Gray Electromagnetic Clutch NOT included — see W10754448 (sold separately) Compatible Brands Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Crosley, Estate, Jenn-Air, Roper, Magic Chef, Admiral, Kirkland Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Work Gloves Disconnect power and turn off the water supply before beginning. Place towels under the washer — some residual water may spill from hoses during disassembly. Wear work gloves to protect your hands. Unthread the hot and cold water supply hoses from the inlet valve ports. Disconnect the drain hose from the outlet port using channel-lock pliers to release the spring clamp. Carefully tip the washer onto its side or back on a padded surface to access the underside. Disconnect the wiring harnesses to the drive motor and pull the rotor free — be prepared for some resistance, as the permanent magnets in the rotor require some effort to remove. Use a small awl inserted between the slider gear teeth to release the spring retainer. With the retainer released, pull off the old spring and slider gear. Note the orientation of the slider — teeth facing outward. Install the new W10734521 components in sequence: slide the new slider gear onto the drive assembly shaft with teeth facing outward, install the new spring support and 30mm spiral, and secure with the new bolt. Reinstall the rotor (the magnets will pull it into place), reconnect the wiring harnesses, return the washer to upright, reconnect supply hoses and drain hose, restore power and water, and test the spin cycle for proper function. Tools needed: Phillips screwdriver, socket set, channel-lock pliers, small awl, padded surface for tipping, work gloves. Frequently Asked Questions What's the difference between W10734521 and W10754448? These are two different parts in the same drive system. The W10734521 is the clutch slider kit — it includes the slider gear, spring support, spiral, and bolt that physically engage/disengage the inner tub from the gearcase to transition between agitation and spin modes. The W10754448 is the electromagnetic clutch itself — the electrical component that drives the engagement. Both can fail independently, and many repair scenarios call for replacing both at the same time since they work together. Confirm exactly which component has failed before ordering, or order both if you're rebuilding the drive system as a full repair. My washer won't spin — is it the slider or something else? A washer that won't spin can have several causes: a failed slider kit, a failed electromagnetic clutch (W10754448), a damaged drive belt, a failed motor or rotor, a broken lid switch, or — on some models — a failed gearcase. The slider kit is one of the more common causes when the symptom is "fills and drains but won't spin" with no obvious noise or burning smell. Before replacing the slider, check that the lid latch strike (W11457841 on some models) is engaging properly, the drive belt is intact, and the motor is functioning. If those check out and the slider gear shows visible wear, missing teeth, or a stretched spring, the W10734521 kit is the right repair. Should I replace all parts in the kit together? Yes — for the kit to perform as designed, all components should be replaced as a matched set. The slider, spring support, spiral, and bolt all work together — if one is worn, the others have typically experienced the same load and wear. Reusing old components alongside new ones can cause premature failure of the new parts and a repeat repair. The W10734521 kit is priced and packaged for a complete replacement, so install all four pieces during your repair. What is the difference between W10734521 and the older part numbers it replaces? W10734521 is the current production version of this slider kit. It directly supersedes W10006484, W10006494, W10275082, W10447975, and W10905025 — all of which were earlier OEM part numbers for variations of the same slider kit across production revisions. Whirlpool consolidated these into the W10734521 to streamline the parts catalog. If your washer's parts diagram shows any of these older numbers, the W10734521 is the correct current replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from metal and plastic to match the dimensions, gear profile, and drive engagement function of the original W10734521 clutch slider kit used in compatible Whirlpool, Maytag, Kenmore, and related HE top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less