Search results for "Defrost Heater"

XPARTCO DA61-14306A Refrigerator Drain Tube Clip The XPARTCO DA61-14306A is an aftermarket replacement drain tube clip (also called a drain clip or defrost drain heater plate) compatible with select Samsung French door and side-by-side refrigerators. This clip solves one of the most common and frustrating Samsung refrigerator problems: water and ice collecting under the crisper or deli drawer. The clip attaches to the defrost heater in the evaporator compartment and extends a metal tab down into the defrost drain opening — conducting heat directly into the drain line during each defrost cycle. That heat keeps the drain from freezing shut, so meltwater can flow freely down to the drain pan instead of backing up and refreezing inside the refrigerator. When the defrost drain freezes over, meltwater from the defrost cycle has nowhere to go. It backs up, spills over into the fresh food compartment, and forms a sheet of ice under the crisper drawers — the signature Samsung symptom. The DA61-14306A is the improved design that supersedes the earlier DA61-06796A, with a longer heat-transfer tab that reaches further into the drain line. Metal construction, heat-resistant, designed for the freezer environment. It directly replaces DA61-14306A, DA61-06796A, AP7020625, PS16622001, EAP16622001, and PD00076719. Important: the clip alone won't fix a drain that is already frozen or clogged — see the installation notes below. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DA61-14306A Refrigerator Drain Tube Clip fixes Samsung French door and side-by-side refrigerators with water pooling or ice sheets forming under the crisper/deli drawer, a frozen defrost drain, or water leaking onto the floor. The clip extends the defrost heater's warmth into the drain line so it can't freeze shut. Improved design superseding DA61-06796A. Metal, heat-resistant. Replaces DA61-06796A, AP7020625, PS16622001, EAP16622001, PD00076719. Important: you must also thaw and clear the existing drain line — the clip prevents future freezing but won't clear an existing blockage. Common Problems This Part Fixes Water collecting under the crisper or deli drawer — the classic Samsung frozen-drain symptom Sheet of ice forming under the crisper drawers or on the floor of the fresh food compartment Water leaking out of the refrigerator onto the kitchen floor Defrost drain frozen shut — meltwater can't reach the drain pan Ice buildup in the evaporator drain trough Repeated re-freezing of the drain line after manual thawing Food at the back of the fresh food compartment freezing (a related airflow/defrost symptom) Drain clip missing, broken, or the original DA61-06796A not reaching far enough into the drain Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drain tube clip directly replaces the following OEM and cross-reference part numbers: DA61-14306A, DA61-06796A, AP7020625, ASM30895, PD00076719, EAP16622001, PS16622001. DA61-14306A is the improved design that supersedes DA61-06796A. If your refrigerator originally used the DA61-06796A, the DA61-14306A is a direct upgrade. Contact our support team with your model number if you need confirmation before ordering. Compatibility This drain tube clip is compatible with select Samsung refrigerators, including: Samsung French door refrigerators — RF-series models experiencing defrost drain freezing (including RF266ABRS/XAA and related) Samsung French door refrigerators — RFG-series models (including RFG298HDBP/XAA and related) Samsung side-by-side refrigerators — select models with the same evaporator drain design Samsung bottom-freezer refrigerators — select models Note: This clip fits a broad range of Samsung refrigerators with the common evaporator drain design. Because it's an improved replacement for the DA61-06796A, it may fit models where the original clip is listed even if the DA61-14306A isn't shown in the parts diagram. Always verify your refrigerator's model number before ordering. Contact our support team with your model number if you're unsure. Key Features Drain tube clip (drain clip / defrost drain heater plate) — extends the defrost heater's warmth into the drain line to prevent it from freezing shut Solves the notorious Samsung "water and ice under the crisper drawer" problem at its root cause Improved design with a longer heat-transfer tab that reaches further into the drain than the original DA61-06796A Keeps the defrost drain open so meltwater flows freely to the drain pan instead of backing up into the fresh food compartment Durable, heat-resistant metal construction designed for the freezer environment Direct supersession of DA61-06796A — a drop-in upgrade for models that originally used the older clip Replaces AP7020625, PS16622001, EAP16622001, and PD00076719 Compatible with Samsung French door, side-by-side, and bottom-freezer refrigerators Inexpensive fix for a problem that otherwise leads to repeated manual defrosting Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number XPDA61-14306A Supersedes DA61-06796A Part Type Refrigerator Drain Tube Clip (Defrost Drain Heater Plate) Condition Aftermarket Replacement Application French Door, Side-by-Side & Bottom-Freezer Refrigerators (Samsung) Function Conducts defrost heater warmth into the drain line to prevent freezing Material Heat-resistant metal Location Evaporator compartment — clips to defrost heater, extends into drain opening Also Known As Drain clip, defrost drain clip, drain heater plate Often Paired With Drain Tube (DA97-04049D, sold separately) Compatible Brands Samsung Installation Notes ⚠️ Unplug Refrigerator First — CRITICAL: Thaw and Clear the Drain Line, or the Repair Won't Work Unplug the refrigerator and safely store any food that could spoil. Wear work gloves. This is the most important thing to understand about this repair: installing the clip alone will NOT fix a drain that is already frozen or clogged. The clip prevents the drain from freezing in the future — it does not clear an existing blockage. You must first thaw and clear the drain line completely, or water will continue to back up. Remove the shelves, drawers, and the rear evaporator access panel in the freezer to expose the evaporator coils, defrost heater, and drain trough. If there's ice buildup, let it thaw fully — never chip or pry ice off the evaporator coils, as the aluminum fins damage easily. Thaw the drain line: hot water in a pump sprayer or garden sprayer works well to flush the drain passage from the evaporator down to the compressor compartment. Keep flushing until water flows freely all the way through to the drain pan. Also inspect the drain tube itself (Samsung DA97-04049D, sold separately) — lint and debris commonly build up inside it, and a clogged tube will re-block the drain no matter what clip you install. If the tube is dirty or restricted, replace it. Once the drain is confirmed clear and flowing, remove any old drain clip that's present. Install the new DA61-14306A by clipping it securely onto the defrost heater element and seating the heat-transfer tab down into the drain opening — good metal-to-metal contact with the heater is essential, since the clip works by conducting heat. Confirm the tab reaches into the drain passage. Reinstall the evaporator panel, shelves, and drawers, plug the refrigerator back in, and monitor over the next few defrost cycles to confirm water is reaching the drain pan and no ice is re-forming under the crisper. Tools needed: Phillips screwdriver, nut driver, pump sprayer or garden sprayer (for hot water), towels, work gloves. Frequently Asked Questions Why is water and ice collecting under my crisper drawer? This is the classic symptom of a frozen defrost drain, and it's extremely common on Samsung refrigerators. Here's the chain of events: your refrigerator periodically runs a defrost cycle to melt frost off the evaporator coils. That meltwater is supposed to run down a drain trough, through a drain tube, and into a pan near the compressor where it evaporates. But if the drain opening freezes shut, the meltwater has nowhere to go — it backs up, overflows the trough, and runs forward into the fresh food compartment, where it pools and refreezes under the crisper drawers. Each defrost cycle adds more water, building a thicker sheet of ice. The DA61-14306A clip fixes the root cause by extending heat from the defrost heater into the drain, keeping it thawed so water can always escape. Will installing this clip fix my problem by itself? Not by itself — and this is critical to understand before you start. The clip prevents the drain from freezing going forward, but it does not clear a drain that's already blocked. If your drain line is currently frozen or clogged with debris, you must thaw and flush it clear first, or water will keep backing up regardless of the new clip. Use hot water in a pump sprayer to flush the drain passage from the evaporator down to the compressor compartment until water flows freely. Additionally, the drain tube running to the compressor compartment (Samsung DA97-04049D) often accumulates lint and debris — appliance technicians routinely recommend replacing it as part of this repair. Skipping these steps is the number one reason people install the clip and see no improvement. What's the difference between DA61-14306A and DA61-06796A? They serve the same function, but the DA61-14306A is the improved, later design. Its heat-transfer tab is longer and reaches further into the drain line, so it delivers heat more effectively deep into the passage where freezing typically starts. The DA61-06796A was the earlier version. If your refrigerator's parts diagram shows DA61-06796A, the DA61-14306A is a direct drop-in upgrade — many customers specifically seek out the newer clip for this reason. Both mount to the defrost heater the same way. My model isn't listed as compatible — can I still use this? Possibly. Because the DA61-14306A is an improved replacement for the widely-used DA61-06796A, it fits a broad range of Samsung refrigerators with the common evaporator drain design — sometimes including models where the parts lookup doesn't list it explicitly. Appliance technicians have confirmed it can be used on models beyond its official listing. That said, the effectiveness of the repair still depends entirely on the drain line being thoroughly cleared. If your model isn't listed and you're unsure, contact our support team with your model number and we'll help confirm fit. Should I also replace the drain tube? In most cases, yes — appliance technicians routinely recommend it. The drain tube (Samsung DA97-04049D, sold separately) runs from the evaporator section down to the compressor compartment, and over years of use it accumulates lint, dust, and debris that restrict flow. Even with a working drain clip keeping the upper drain thawed, a clogged tube downstream will still cause water to back up. Since you'll already have the refrigerator open for the clip installation, inspecting and replacing the tube at the same time is the efficient move — and it's a common reason the repair fails when people skip it. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from heat-resistant metal to match the fit, heat-transfer function, defrost heater mounting, and drain-tab geometry of the original DA61-14306A drain tube clip used in compatible Samsung French door, side-by-side, and bottom-freezer refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

DA32-00029X Genuine OEM Samsung Refrigerator Temperature Sensor The DA32-00029X is a Genuine OEM Samsung replacement refrigerator temperature sensor compatible with select Samsung side-by-side and French door refrigerators, as well as related Kenmore Samsung-built models. This NTC (negative temperature coefficient) thermistor continuously monitors the temperature inside the refrigerator and sends resistance-based readings to the electronic control board, which uses this data to cycle the compressor, fans, and defrost heaters to maintain accurate, consistent temperatures throughout the appliance. As the thermistor heats up or cools down, its electrical resistance changes predictably, allowing the control board to calculate the exact temperature in real time. When this sensor fails — whether shorted, open, or providing drifted/inaccurate readings — the refrigerator may run too cold or too warm, cycle excessively, fail to maintain set temperatures, run continuously, ice up the evaporator, or display temperature-related fault codes. As a Genuine OEM part manufactured by Samsung to factory specifications, the DA32-00029X is rated approximately 13.2 kΩ at 20°C (68°F) when functioning correctly. It is one of the variants in the DA32-00029 sensor family — Samsung uses different production-run variants (M, N, Q, U, X) across model generations, all functionally similar but with different wire harness connectors. Installs in 20–30 minutes with basic hand tools. Quick Answer The DA32-00029X Genuine OEM Samsung Refrigerator Temperature Sensor fixes Samsung side-by-side and French door refrigerators that run too cold or warm, cycle excessively, freeze up the evaporator, fail to maintain set temperatures, or display temperature-related fault codes. Genuine OEM Samsung NTC thermistor — approximately 13.2 kΩ at 20°C (68°F). One of the DA32-00029 series variants (M, N, Q, U, X) — confirm your specific variant by connector style before ordering. Common Problems This Part Fixes Refrigerator running too cold or too warm — sensor not accurately reporting temperature to the control board Inconsistent temperatures — fluctuating cooling that can't maintain set point Excessive or frequent defrost cycles — control board misreading temperature Refrigerator running continuously without cycling off Heavy frost or ice buildup on the evaporator coils caused by erratic defrost timing Food spoilage from temperature instability Temperature-related error codes displayed on the control panel Multimeter test shows 0 ohms (shorted) or infinite resistance (open) instead of the expected ~13.2 kΩ at room temperature Replaces Part Numbers This temperature sensor directly replaces the following Samsung part number: DA32-00029X, EAP16732853, FIX16732853, ASM30292, AP7188139, OEM21564426, PD00090960, PS16732853. The DA32-00029X is part of the broader DA32-00029 sensor family — variants M, N, Q, U, and X are functionally similar Samsung temperature sensors used across different model generations, but with different wire harness connector configurations. They are not automatically interchangeable — match the variant suffix (or the connector style) to your refrigerator. Contact our support team with your model number if you need confirmation before ordering. Compatibility This temperature sensor is compatible with select Samsung side-by-side and French door refrigerators, including: Samsung side-by-side refrigerators (select models in the RS-series with the matching DA32-00029X connector) Samsung 3-door French door refrigerators in 17.5 cu. ft., 19.5 cu. ft., and related capacities (Black Stainless Steel, Black, White, and Stainless Look finishes) Samsung 4-door French door refrigerators (select RF-series models with the matching DA32-00029X connector) Kenmore / Sears refrigerators (select Samsung-built models) Important — Match the Variant to Your Refrigerator: Samsung uses several variants of the DA32-00029 temperature sensor (M, N, Q, U, X) across different model generations. The sensors are similar in function and resistance value, but the wire harness connectors differ — using the wrong variant means the connector won't fit. Before ordering, verify your refrigerator's parts diagram specifies DA32-00029X (not DA32-00029M, N, Q, or U), or visually confirm the connector on your old sensor matches the new one. Contact our support team with your model number if you're unsure. Key Features Genuine OEM part manufactured by Samsung to factory specifications — guaranteed fit and performance NTC (negative temperature coefficient) thermistor — resistance changes predictably with temperature, allowing precise temperature monitoring Sends real-time temperature data to the control board to regulate compressor cycling, fan operation, and defrost timing Approximately 13.2 kΩ of resistance at 20°C (68°F) when functioning correctly Wire harness with connector attached for direct plug-in installation (variant-specific connector — see compatibility note) One of the DA32-00029 series variants (M, N, Q, U, X) — match to your refrigerator's variant suffix Compatible with select Samsung side-by-side, 3-door French door, and 4-door French door refrigerators, plus Kenmore Samsung-built models Installs in 20–30 minutes with basic hand tools Product Specifications Part Number DA32-00029X Part Type Refrigerator Temperature Sensor (NTC Thermistor) Condition Genuine OEM Application Side-by-Side and French Door Refrigerators (Samsung platform) Sensor Type NTC (Negative Temperature Coefficient) Resistance at 20°C Approximately 13.2 kΩ (68°F) Variant Family DA32-00029 (M, N, Q, U, X variants) Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Refrigerator and Move Perishable Food Before Starting — Wear Work Gloves Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves to protect your hands. Samsung refrigerators typically have multiple temperature sensors — fresh food compartment, freezer compartment, and evaporator/defrost sensors — confirm which sensor location matches your symptom and parts diagram before starting. The fresh food and freezer sensors are typically clipped to a wall or shelf bracket inside each compartment, while evaporator/defrost sensors are mounted near the evaporator coils behind a rear access panel. Take a photo of the sensor mounting and wire routing before removing. Disconnect the sensor's wire connector (gently — the molex connectors can be fragile) and release the sensor from its mounting clip. Inspect the connector for corrosion or heat discoloration on the wires — discoloration indicates prior overheating in that area. Install the new DA32-00029X sensor in the same position, reseat the connector firmly, and secure the mounting clip. Restore power, allow several hours for the refrigerator to return to its set temperature, and confirm stable temperature operation before reloading with food. Tools needed: Phillips screwdriver, multimeter (for testing), work gloves. Frequently Asked Questions How do I know if the temperature sensor has failed? Unplug the refrigerator, disconnect the sensor's connector, and set your multimeter to resistance mode. At room temperature (around 20°C/68°F), a working NTC thermistor should read approximately 13.2 kΩ. If the sensor reads 0 ohms, it has shorted internally. If it reads infinite resistance (open circuit, often shown as "OL" on the multimeter), the sensor has failed open. Either reading confirms the sensor needs replacement. If the sensor reads close to 13.2 kΩ at room temperature but the refrigerator still has temperature problems, the control board or another sensor in the system may be the actual cause. My Samsung refrigerator has multiple temperature sensors — which one do I replace? Samsung refrigerators typically use multiple temperature sensors: one in the fresh food compartment, one in the freezer compartment, and one near the evaporator coils (often called the defrost sensor). The DA32-00029X is used as the fresh food or freezer compartment temperature sensor on select Samsung models. Confirm the exact mounting location for your specific symptom (e.g., fresh food too warm vs. freezer too cold) and your refrigerator's parts diagram before ordering. The evaporator/defrost sensor is typically a different part number, so don't assume the DA32-00029X covers all sensor positions. What is the difference between DA32-00029X and DA32-00029M, N, Q, or U? These are all variants of the same Samsung refrigerator temperature sensor family. They share the same NTC thermistor design and resistance characteristics (approximately 13.2 kΩ at 20°C), but use different wire harness connector configurations to match different refrigerator generations and wiring designs. The X variant is used on select Samsung side-by-side and French door models, while M, N, Q, and U variants appear on other model groups. They are not automatically interchangeable — match the variant to your refrigerator's exact part diagram, or visually compare connector styles before ordering. My Samsung fridge is icing up the back wall — could this be the sensor? Possibly, yes. If the temperature sensor near the evaporator (the defrost sensor) is misreporting temperature, the control board may not trigger the defrost cycle when needed, allowing ice to build up on the evaporator coils. Eventually this ice migrates to the rear interior wall as a frozen sheet. If your symptom is back-wall icing combined with poor cooling, the evaporator sensor is a likely cause — but confirm whether the DA32-00029X is the evaporator sensor on your specific model, or whether your model uses a different part number for that position. Always verify against your model's parts diagram. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Samsung to factory specifications. It is the exact same temperature sensor installed in compatible Samsung side-by-side and French door refrigerators (and Kenmore Samsung-built models) from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3387747 Dryer Heating Element Replaces WP3387747 The XPARTCO 3387747 is an aftermarket replacement heating element assembly for Whirlpool, Kenmore, Maytag, KitchenAid, Amana, and Roper electric dryers. This element is the source of virtually all the heat in the dryer: current flows through a nickel-chromium coil, which glows and radiates heat as the blower pushes air across it and into the drum. Everything downstream — the drum temperature, the drying time, the final dampness of your clothes — depends on this coil working correctly. Rated 5400W at 240V, with two 5/16" terminals for a direct connection. The nickel-chromium coil is rated at roughly 85% nickel-chromium content for effective, heat-and-abrasion-resistant heating, and it's mounted in high-temperature ceramic insulators that hold it firmly in the frame so it won't loosen or shift under the vibration of a running dryer. Over years of use, the coil itself typically fails with a visible break somewhere along its length — a section simply burns through and the circuit opens, cutting off heat entirely. It directly replaces WP3387747, WP3387747VP, W11045584, W11344457, 80003, 525502, AP6008281, AP2947033, PS344597, PS11741416, EAP11741416, FIX11741416, AWP47520, and PD00002365. Quick Answer The XPARTCO 3387747 Dryer Heating Element fixes Whirlpool, Kenmore, Maytag, KitchenAid, Amana, and Roper electric dryers with no heat, insufficient heat, or drying times that have gotten noticeably longer. 5400W, 240V, two 5/16" terminals. Replaces WP3387747, WP3387747VP, W11045584, W11344457, 80003, 525502, AP6008281, AP2947033, PS344597, PS11741416, EAP11741416, FIX11741416, AWP47520, PD00002365. If the dryer has no heat at all, check the thermal fuse first — it's a cheaper, faster fix, and a blown fuse produces the same "no heat" symptom as a failed element. Common Problems This Part Fixes Dryer runs a full cycle but produces no heat at all Dryer produces some heat, but not enough to dry clothes properly Drying times that have gotten noticeably longer than they used to Clothes coming out cold or barely warm at the end of a cycle Visible break or burned-through section in the heating coil Element that tests as an open circuit (no continuity) with a multimeter Dryer that heats inconsistently, cycling on and off unexpectedly Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer heating element directly replaces the following OEM and cross-reference part numbers: WP3387747, WP3387747VP, W11045584, W11344457, 80003, 525502, AP6008281, AP2947033, PS344597, PS11741416, EAP11741416, FIX11741416, AWP47520, PD00002365 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This heating element is compatible with select Whirlpool electric dryers, and also fits select Kenmore, Maytag, KitchenAid, Amana, and Roper dryers built on the same platform, including model numbers such as: GEW9200LW0, GEW9200LW1, GEW9250PL0, GEW9250PW0, GEW9250PW1 GEQ9800PW1, GEQ9800PW2 MEDB835DW4, MEDC700VW0 WED5100HW1, WED5500XW1, WED5700AC1, WED6120HW1, WED6620HW1, WED8300SW2 MED5500FW1, MED6230HW1, MED6230RHW1 Kenmore 110.82822101 Note: Always verify your full model number before ordering, since Whirlpool uses several different heating elements across its dryer lineup. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement heating element assembly — generates the heat that dries clothes Resolves "no heat," "insufficient heat," and "drying takes too long" symptoms caused by a burned-through coil Nickel-chromium coil (approx. 85% Ni-Cr content) for effective, heat-and-abrasion-resistant heating High-temperature ceramic insulators hold the coil firmly in the frame against vibration Rated 5400W at 240V Two 5/16" terminals for a direct connection Approximately 10"L x 6"W x 1"H Direct drop-in replacement — no modification required Replaces WP3387747VP, W11045584, W11344457, 80003, 525502, AP6008281, AP2947033, PS344597, PS11741416, EAP11741416, FIX11741416, AWP47520, and PD00002365 Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, and Roper electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 3387747 OEM Part Number WP3387747 Part Type Dryer Heating Element Assembly Condition Aftermarket Replacement Wattage 5400 W Voltage 240V Terminals 2 (5/16") Coil Material Nickel-chromium (approx. 85% Ni-Cr) Insulators High-temperature ceramic Dimensions Approx. 10"L x 6"W x 1"H Repair Difficulty Medium — basic electrical skills and dryer panel disassembly required Quantity 1 heating element assembly Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper Installation Notes ⚠️ Unplug Dryer Before Starting — Test Continuity Before Assuming It's The Element Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel or the front, depending on your model, to reach the heater duct/blower housing area where the element is mounted. Before removing anything, test the old element with a multimeter set to continuity — a healthy element reads continuous end to end, while a failed one (with a visible break in the coil) reads open. Photograph the wiring before disconnecting anything. Disconnect the two wire terminals from the old element, remove the mounting screws or clips holding it in the duct housing, and pull it free. Install the new 3387747 assembly in the same position, reconnect the two wire terminals, and secure the mounting hardware. While the dryer is open, this is a good time to fully clean the exhaust vent ducting from the lint trap to the outside vent hood — restricted airflow is a major cause of heating element failure, and a fresh element installed into a clogged system will likely fail again prematurely. Reassemble the panel, restore power, and run a test cycle to confirm the dryer is heating normally. Tools needed: 1/4" nut driver, 5/16" wrench, Phillips screwdriver, multimeter, work gloves. Frequently Asked Questions My dryer has no heat at all. Should I replace the element first, or check something else? Check the thermal fuse first. A blown thermal fuse produces the exact same "no heat at all" symptom as a failed heating element, and it's a much cheaper, faster part to test and replace. Whirlpool's own service guidance recommends checking the thermal fuse before replacing the element. If the fuse tests good and the dryer still has no heat, the element itself is the next thing to test and likely replace. How can I tell if the element has actually failed? The most reliable way is a continuity test with a multimeter — set it to continuity mode, disconnect the element's wires, and touch a probe to each terminal. A healthy element shows continuity (a complete circuit); a failed one shows open (no continuity), which usually corresponds to a visible break or burned-through section somewhere in the coil if you inspect it closely. Why does the listing recommend cleaning the vent duct during this repair? Restricted airflow from a lint-clogged exhaust duct is one of the most common root causes of heating element failure — when air can't move through the system properly, heat builds up around the element well beyond its designed operating range, accelerating wear and often leading directly to a burned-through coil. Since you'll already have the dryer open for this repair, cleaning the full duct run from the lint trap to the outside vent hood is a good use of the same trip and helps the new element last. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the 5400W/240V electrical rating, nickel-chromium coil composition, ceramic insulator mounting, and terminal configuration of the original WP3387747 heating element used in compatible Whirlpool, Kenmore, Maytag, KitchenAid, Amana, and Roper dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

154825001 Genuine OEM Frigidaire Dishwasher Heating Element The 154825001 is a genuine Frigidaire OEM round heating element that sits exposed at the bottom of the dishwasher tub. Unlike a hidden element concealed beneath the tub floor, this is a visible ring-shaped element you can see sitting right in the bottom of the wash chamber. It serves two jobs: it heats the wash water to the temperature needed to properly dissolve detergent and break down grease and food soil, and at the end of the cycle it provides the heat that drives the drying phase, helping moisture evaporate off your dishes rather than leaving them wet. Mounted through a 0.98" hole with two mounting nuts and connected by two wire terminals, this element carries a pair of white alignment dots that must line up with the tub's retaining clips during installation. Over time, mineral buildup from hard water, general corrosion, or simple electrical wear can cause the element to fail. A failing or dead element produces a specific and recognizable pattern: water never gets hot enough to clean effectively, dishes come out wet at the end of the cycle instead of dry, and the whole cycle may run noticeably longer as the dishwasher's control tries to compensate. It directly replaces AP5628696, 154482901, 154663801, 2308825, PS3653449, and EAP3653449. As a genuine OEM part, the 154825001 is manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. Quick Answer The 154825001 Genuine OEM Frigidaire Dishwasher Heating Element fixes Frigidaire, Kenmore, Electrolux, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse dishwashers with dishes that don't get properly clean, dishes that come out wet instead of dry, or cycles that take longer than they used to. Exposed round heating element, 0.98" mounting hole, 2 wire terminals. Replaces AP5628696, 154482901, 154663801, 2308825, PS3653449, EAP3653449. Before replacing, test the old element with a multimeter for resistance — a bad control board relay can produce identical symptoms with a perfectly good element. Common Problems This Part Fixes Dishes not getting properly clean because wash water isn't reaching the correct temperature Dishwasher not drying dishes — items come out wet at the end of the cycle Cycle taking noticeably longer than usual to complete Visible damage, corrosion, or discoloration on the element itself Element that doesn't glow or heat up when the wash cycle is running Water leaking near the high-temperature wire connector at the element terminals Mineral scale buildup visible on or around the element Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher heating element directly replaces the following OEM and cross-reference part numbers: 154825001, 154482901, 154663801, 2308825, AP5628696, AFR14520, EAP3653449, PD00000951, PS3653449. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This heating element is compatible with select Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse dishwashers, spanning a wide range of model series including BBBD, BGBD, BGHD, DGBD, DGCD, DGHD, FDB, FDBB, FDBD, FFBD, FFID, FGBD, FGCD, FGHD, FGID, FPHD, FPID, GLD, GSB, LEDB, LFBD, LFID, LGBD, LGHD, and PLD. Verified model numbers include: FFCD2413UW1A, FGID2466QF4A, FGID2466QF5A, FFID2426TD1A, FGBD2438PF4A, FGHD2465NF1A, FGHD2433KF1, LFID2426TF1A, LFID2422RF0A, LFID2422RF3B, LFID2422RF4B, LFID2426TF4A, LFID2426TF5A, LGBD2431LF0A, LGBD2431NF0B, LGBD2431NF1B, LGBD2432LW0A, LGBD2432LW0B, and CDB350/CDB500/CDB900 series models. Also fits Kenmore 587-series, Crosley CBD-series, Kelvinator KADB240, and White-Westinghouse WWBD2400 dishwashers. Note: This is an exposed round heating element sitting visibly in the bottom of the tub, not a hidden element mounted underneath. It is not interchangeable with hidden/concealed heating elements used on other dishwasher platforms. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified heating output and terminal configuration Exposed round design sits in the tub bottom for direct water heating and drying support Resolves "not cleaning properly," "not drying," and "cycle taking too long" symptoms caused by element failure 0.98" mounting hole with two mounting nuts and wire terminals Two white alignment dots for correct positioning in the tub's retaining clips Direct drop-in replacement — no modification required Replaces 154482901, 154663801, 2308825, AP5628696, PS3653449, and EAP3653449 Compatible with Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 154825001 Part Type Dishwasher Round Heating Element (Exposed) Condition Genuine OEM Brand Frigidaire / Electrolux Location Bottom of the wash tub (exposed, visible) Mounting Hole 0.98 in. Terminals 2 wire connections + 2 mounting nuts Alignment 2 white dots must align with tub retaining clips Repair Difficulty Medium — basic dishwasher familiarity required Tools Required Screwdrivers, wrench set Quantity 1 heating element Compatible Brands Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, Westinghouse Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Before Starting — Handle The Element Carefully Disconnect power at the circuit breaker and shut off the water supply before beginning. Wear work gloves. On many models you'll need to pull the dishwasher out from under the counter to access the undercarriage — remove the two screws securing the unit to the counter first. Remove the lower rack and the lower spray arm (it typically pushes down and twists to unlock) to access the element inside the tub. From underneath, disconnect the two wires from the element's terminals and remove the two mounting nuts with a 1/2" wrench, taking care not to overtighten when you reach the new element — over-torquing can crush the sealing washers and cause a leak at the connector. Lift the old element free from its retaining clips inside the tub. To install the new 154825001, locate the two white alignment dots on the element and position them so they slide into the tub's retaining clips correctly — this ensures the element seats in its proper orientation. Push the terminals down through the mounting hole, then from underneath, reinstall and tighten the mounting nuts snugly but not excessively. Reconnect the two wires to the terminals, reinstall the lower spray arm and press it down to lock it in place, and reinstall the lower rack. Restore water and power, then slide the dishwasher back into place and secure it to the counter with its mounting screws. Run a test cycle and check underneath for any leaks at the element connection before considering the repair complete. Tools needed: screwdriver, 1/2" wrench, work gloves. Frequently Asked Questions How do I know it's the heating element and not something else, like the control board? Before replacing the element, it's worth testing it with a multimeter for resistance — a healthy element typically reads in the neighborhood of 14 ohms, though exact values vary by model. If the old element tests fine but dishes still aren't drying or getting hot enough, the more likely cause is upstream of the element itself, such as a control board relay that isn't sending power to it correctly. Some owners have replaced a perfectly good element only to find the actual fault was a bad solder connection on the control board relay — testing first can save you an unnecessary purchase. Can I clean the element instead of replacing it? Light surface cleaning to remove mineral scale buildup is reasonable and can sometimes help if reduced heating output is due to scale insulating the element. However, if the element tests as an open circuit (no continuity) or shows visible damage, cracking, or corrosion through the metal sheath, cleaning won't restore it — replacement is the correct fix at that point. I noticed water leaking near the element's wire connector. Is that related? Yes, this is a documented failure point on this element design — the high-temperature wire connector at the terminals can develop a leak, especially if the mounting nuts were overtightened during a prior installation and damaged the sealing washer. When installing the new element, tighten the mounting nuts snugly but avoid excessive force, which helps prevent this same leak point from recurring. Do I really need to pull the dishwasher out from under the counter? On most installations, yes — accessing the mounting nuts and wire terminals underneath the tub requires pulling the unit forward after removing the two screws that secure it to the counter. Some technicians have managed the nut removal with a deep socket without fully pulling the unit, but planning for full access makes the job considerably easier, especially the first time. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original heating output, mounting configuration, and terminal layout of the element originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

ERWR50X122 Refrigerator Defrost Thermostat  L60-32F. 1/4" side push on clip. 11-3/4" leads with stripped wire ends. Replaces Part Numbers: WR50X122, 2387, AH303471, AP2071262, EA303471, PS303471, WR50X0122, WR50X0128, WR50X10014, WR50X128   This is an aftermarket part that can be used as a replacement for the OEM part.  California Residents Only - Warning: Cancer and Reproductive harm - https://www.p65warnings.ca.gov/

Read more less

240597220 Genuine OEM Frigidaire Refrigerator Temperature Sensor The 240597220 is a Genuine OEM Frigidaire replacement refrigerator temperature sensor compatible with a wide range of Frigidaire, Electrolux, Kenmore (253/106/795 prefix), Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, and Ikea refrigerators and household freezers. This NTC (negative temperature coefficient) thermistor continuously monitors the temperature inside the refrigerator or freezer compartment and sends resistance-based readings to the main control board, which uses this data to cycle the compressor, fans, and defrost heaters to maintain accurate temperatures. As the thermistor heats up or cools down, its electrical resistance changes predictably, allowing the control board to calculate the exact temperature in real time. When this sensor fails or drifts out of range, the refrigerator may run too cold or too warm, cycle excessively, freeze up the evaporator, fail to maintain set temperatures, or display OP error codes. Rated 10K Ohm NTC, with a 5/16" diameter probe, 12" wire, and overall dimensions of 3-5/8"L x 5/8"W x 5/16"H (sensor probe itself measures ~1-3/16"L x 5/16" diameter). Compatible with 20-28 cubic foot North American household refrigerators in French door, side-by-side, top-freezer, and bottom-freezer configurations (post-2005 production). 240597220 is the current OEM part number, superseding 240597203, 240597201, and 240597202. It also replaces 7240597203, AP4032998, AP7243155, AH1765215, EA1765215, EAP1765215, EAP17647917, 1258948, 4985585, OEM21729470, PD00000590, PD00088922, PS1765215, and PS17647917. Not compatible with mini fridges, car refrigerators, commercial units, wine coolers, or ice makers. Installs in 15–20 minutes with basic hand tools. Quick Answer The 240597220 Genuine OEM Frigidaire Refrigerator Temperature Sensor fixes Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, and Ikea refrigerators that run too cold or warm, cycle excessively, freeze up the evaporator, or display OP error codes. NTC thermistor — 10K Ohm at room temperature. 5/16" probe diameter, 12" wire. Overall 3-5/8"L x 5/8"W x 5/16"H. Genuine OEM. Supersedes 240597203, 240597201, 240597202. Also replaces 7240597203, AP4032998, AP7243155, AH1765215, EA1765215, EAP1765215, EAP17647917, 1258948, 4985585, OEM21729470, PD00000590, PD00088922, PS1765215, PS17647917. For 20–28 cu ft household refrigerators built 2005 or later. Common Problems This Part Fixes Refrigerator running too cold or too warm — sensor not accurately reporting temperature Inconsistent temperatures — fluctuating cooling that can't maintain set point OP error code displayed on the control panel (open sensor circuit) Excessive frost or ice buildup on evaporator coils from erratic defrost timing Refrigerator running continuously without cycling off Freezer over-freezing food or fresh food compartment freezing groceries Food spoilage from temperature instability Multimeter test shows 0 ohms (shorted), infinite resistance (open), or drifted resistance instead of the expected ~10K Ohms at room temperature Replaces Part Numbers This temperature sensor is the current OEM part number and supersedes the following OEM and cross-reference part numbers: 240597220, 240597203, 240597201, 240597202, 7240597203, 4985585, AFR15666, AP7243155, EAP17647917, OEM21729474, PD00088922, PS17647917. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This temperature sensor is compatible with select household refrigerators and freezers from the following brands (20–28 cu ft, built 2005 or later): Frigidaire refrigerators — Gallery and Professional series, plus standard Frigidaire models (BFHS2611LM, BGHS2634KE, BGHS2634KP, BGHS2644KF, CRSH237LB, PRFG2383AF, PRFC2383AF, ERFG2393AS2, FRSS2323AS8, FFHB2740PP5A and many related models) Frigidaire upright freezers — FFFH21F7QW, FGU19F6QWB and related models Electrolux refrigerators — EI24RD65KS0, EI24RD65HS0, EI24RD65HS1, E24RD75KPS0 and related models Kenmore / Sears refrigerators — 253-prefix, 106-prefix, and 795-prefix models (select Frigidaire/Electrolux-built units) Crosley refrigerators (select Frigidaire-built models) White-Westinghouse refrigerators (select models) Kelvinator refrigerators (select models) Gibson refrigerators (select models) Tappan refrigerators (select models) Viking refrigerators (select Frigidaire-platform models) Ikea refrigerators (select Frigidaire-platform models) Not compatible with: mini fridges, car refrigerators, commercial refrigerators/freezers, wine coolers, or dedicated ice makers. Verify your refrigerator was produced after 2005 and check the original part number on the fridge nameplate matches one of the cross-references listed. Contact our support team with your model number if you're unsure. Key Features NTC (negative temperature coefficient) thermistor — resistance changes predictably with temperature, allowing precise temperature monitoring Rated 10K Ohms at room temperature (approximately 25°C / 77°F) Sends real-time temperature data to the main control board to regulate compressor cycling, fan operation, and defrost timing Sensor probe: 5/16" diameter x 1-3/16" length · Overall assembly: 3-5/8"L x 5/8"W x 5/16"H · 12" wire lead White plastic/metal construction with glossy finish Resolves OP error codes when caused by an open sensor circuit Compatible with 20–28 cu ft French door, side-by-side, top-freezer, and bottom-freezer refrigerators built 2005 or later Current OEM part number — supersedes 240597203, 240597201, 240597202 and replaces AP4032998, AH1765215, PS1765215, PS17647917 and additional cross-references Compatible with Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, Ikea Genuine OEM part manufactured by Frigidaire/Electrolux to factory specifications — guaranteed fit and performance Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number 240597220 Supersedes 240597203, 240597201, 240597202 Part Type Refrigerator Temperature Sensor (NTC Thermistor) Condition Genuine OEM Application Household Refrigerators and Freezers (Frigidaire/Electrolux platform, 20–28 cu ft, 2005+) Sensor Type NTC (Negative Temperature Coefficient) Resistance 10K Ohms at room temperature Probe Dimensions 5/16" Diameter x 1-3/16" Length Overall Dimensions 3-5/8"L x 5/8"W x 5/16"H Wire Length 12" Color White Finish Glossy Material Plastic / Metal Error Codes Resolved OP (open sensor circuit) Compatible Brands Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, Ikea Installation Notes ⚠️ Unplug Refrigerator and Move Perishable Food Before Starting — Wear Work Gloves Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves to protect your hands. Depending on your refrigerator model, the fresh-food temperature sensor is typically located behind the air tower or damper assembly on the rear interior wall of the refrigerator compartment; the freezer temperature sensor is typically located behind the rear freezer access panel near the evaporator coils. Confirm which sensor location matches your symptom and the parts diagram for your specific model before starting. Remove all shelves, drawers, and any items blocking access to the sensor location. Remove the screws holding the air tower/damper cover (fresh food side) or rear freezer access panel to expose the sensor. Photograph the sensor position, wire routing, and connector before removing. Disconnect the wire connector (gently — the connector can be fragile) and release the sensor from its mounting clip. Fully insert the new 240597220 sensor probe into the card slot (no exposure) and secure with the mounting clip. Reconnect the wire connector — plug wiring terminals tightly to avoid poor contact. Use cable ties to secure any loose wire routing as before. Reinstall the cover or panel, replace the shelves and drawers, and plug the refrigerator back in. Allow several hours for the refrigerator to return to its set temperature before reloading with food. Tools needed: Phillips screwdriver, cable ties, multimeter (for testing), work gloves. Frequently Asked Questions What does OP error code mean on my Frigidaire refrigerator? The OP error code (Open) indicates the control board is detecting an open circuit on a temperature sensor input — meaning the sensor is failing to send a resistance signal, either because the sensor itself has failed open internally, the wire has broken, or the connector isn't seated. Replacing the temperature sensor typically resolves the code when the sensor itself is the cause. If the code persists after replacement, check the wire harness between the sensor and the control board for damage, and confirm the connector is fully seated. If the OP code appears alongside other symptoms like frost buildup and cooling issues that persist after sensor replacement, the defrost temperature sensor (on the Harness-Low Side, a different part number) may also need to be replaced, or the main control board may be at fault. How do I test if the temperature sensor has failed? Unplug the refrigerator, disconnect the sensor's wire connector, and set your multimeter to resistance mode. At room temperature (approximately 25°C / 77°F), a working NTC thermistor should read approximately 10K Ohms. If the sensor reads 0 ohms, it has shorted internally. If it reads infinite resistance (open circuit, often shown as "OL" on the multimeter), the sensor has failed open. If it reads significantly off from 10K (for example 8.4K or 5K at room temp), the sensor has drifted and is no longer providing accurate readings — replacement is recommended. Any of these results confirms the sensor needs replacement. My refrigerator has multiple temperature sensors — which one do I replace? Frigidaire refrigerators typically use multiple temperature sensors: one in the fresh food compartment (behind the air tower/damper), one in the freezer compartment (near the evaporator coils), and often a separate defrost temperature sensor on the Harness-Low Side. The 240597203 is used as the fresh food or freezer compartment temperature sensor. If your symptom is "fresh food too warm" or "freezer over-freezing," the fresh food sensor is the likely candidate. If your symptom is "freezer icing up despite defrost heater working," the defrost temperature sensor may be the culprit — a different part number. Check your refrigerator's parts diagram to confirm the correct sensor location for your specific symptom. Does this sensor fit my Kenmore refrigerator? On many Kenmore refrigerators, yes — Sears sells Kenmore-branded refrigerators that are manufactured by Frigidaire/Electrolux, Whirlpool, LG, and Samsung. The 240597203 sensor fits Kenmore refrigerators with model numbers beginning with the 253, 106, or 795 prefixes that are Frigidaire/Electrolux-built. Kenmore refrigerators built by other manufacturers (Whirlpool, LG, Samsung) use different sensors. Check the first three digits of your Kenmore model number — if it's 253, 106, or 795 and falls within the compatible model list, this is the correct part. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by Frigidaire/Electrolux to factory specifications. It is the exact same temperature sensor installed in compatible Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, and Ikea refrigerators from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DA32-00024W Refrigerator Temperature Sensor The XPARTCO DA32-00024W is an aftermarket replacement temperature sensor for Samsung refrigerators. This sensor senses the temperature inside the refrigerator and sends that information to the electronic control board, which uses it to regulate cooling and, on many models, manage the defrost cycle. The manufacturer designation for this sensor is "SENSOR TEMP;NW2,5V,R-DEF," indicating its role in the defrost-related temperature monitoring circuit. Over time, the sensor's electronics can drift out of calibration or fail outright from age or moisture exposure. A failing sensor typically shows up as inconsistent cooling, temperatures that run warmer or colder than the set point, or increased energy consumption as the refrigerator's control struggles to compensate for inaccurate temperature readings. It directly replaces AP5579174, 3955001, and PS4138632. Quick Answer The XPARTCO DA32-00024W Refrigerator Temperature Sensor fixes Samsung refrigerators with inconsistent cooling, temperatures running warmer or colder than expected, or increased energy consumption. Replaces AP5579174, 3955001, PS4138632. This sensor is tied to defrost-related temperature monitoring on many models — if you're also seeing frost buildup or defrost cycle issues, this sensor is worth checking alongside the defrost thermostat or heater. Common Problems This Part Fixes Inconsistent cooling in the refrigerator or freezer compartment Temperature running warmer or colder than the set point Increased energy consumption from the refrigerator overcompensating Temperature fluctuations affecting food freshness Defrost cycle irregularities on models where this sensor is part of that circuit Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator temperature sensor directly replaces the following OEM and cross-reference part numbers: DA32-00024W, 3955001, AP5579174, ASM30135, EAP4138632, PD00030760, PS4138632. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This temperature sensor is compatible with select Samsung refrigerators, including model numbers RS25H5111SR and RF4287HARS. Note: Samsung uses several different temperature sensors across its refrigerator lineup, including sensors for different compartments and functions. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which sensor your refrigerator needs. Key Features Aftermarket replacement temperature sensor — monitors internal refrigerator temperature Resolves "inconsistent cooling," "temperature off target," and "high energy use" symptoms caused by sensor failure Reports temperature data to the electronic control board for cooling and defrost regulation Direct drop-in replacement — no modification required Replaces AP5579174, 3955001, and PS4138632 Compatible with Samsung refrigerators Aftermarket replacement built to OEM-equivalent quality standards Straightforward installation Product Specifications Part Number XPDA32-00024W OEM Part Number DA32-00024W Part Type Refrigerator Temperature Sensor Condition Aftermarket Replacement Brand XPARTCO Manufacturer Designation SENSOR TEMP;NW2,5V,R-DEF Function Senses internal temperature and reports to the electronic control Repair Difficulty Easy Quantity 1 temperature sensor Compatible Brand Samsung Installation Notes ⚠️ Unplug Refrigerator Before Starting Unplug the refrigerator and safely store any food that could spoil while the power is off before installing this part. Wear work gloves to protect your hands. Locate the old temperature sensor per your model's service diagram, since its position varies by refrigerator model. Photograph the wiring connection before disconnecting anything. Disconnect the wiring harness from the old sensor, remove any mounting clips or fasteners holding it in place, and pull it free. Install the new DA32-00024W in the same position, reconnect the wiring harness fully, and secure any mounting hardware. Restore power and monitor the refrigerator's temperature over the next 24 hours to confirm consistent, accurate cooling has returned. Tools needed: Phillips screwdriver (model-dependent), work gloves. Frequently Asked Questions My refrigerator's temperature seems inconsistent. Is this the part I need? Yes, this is a common symptom of a failing temperature sensor. Since this sensor is what reports internal temperature to the control board, a drifting or failed sensor can cause the refrigerator to run warmer or colder than intended, or to cycle inconsistently as the control tries to work from inaccurate data. What does the "R-DEF" in this sensor's designation mean? This suggests the sensor plays a role in the refrigerator's defrost-related temperature monitoring on applicable models. If you're seeing frost buildup or defrost cycle problems in addition to general cooling inconsistency, this sensor is worth checking alongside other defrost system components, such as the defrost thermostat or heater. Is this a difficult repair? No, replacing this sensor is generally a straightforward repair once you've located its mounting position, which can vary by model. It typically involves disconnecting a wiring harness and removing a small mounting clip or fastener. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the sensing function, voltage reference, and mounting configuration of the original DA32-00024W sensor used in compatible Samsung refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

279838 Genuine OEM Whirlpool Dryer Heating Element The 279838 is a Genuine OEM Whirlpool replacement dryer heating element assembly compatible with a wide range of Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef electric dryers. The heating element is the primary heat source in an electric dryer — a nickel-chromium resistance coil wound around a series of ceramic insulators inside a steel housing. When electricity passes through the coil during the drying cycle, it generates the heat needed to evaporate moisture from clothes. When the element coil burns through at a weak point, the circuit is broken and the dryer produces no heat. This Genuine OEM part is manufactured by Whirlpool to factory specifications and is rated at 5400W / 240V with two 5/16" male terminals. It includes the heating element coil with partial housing and ceramic insulators already mounted — the remaining outer housing from your old assembly is reused. Note: the heating element does not include the thermostat or thermal fuse — those are separate parts. It directly replaces WP279837, 279837, 279838A, 279838VP, 3398063, 3398064, 3403585, 8565582, W10724237, 2438, AP3094254, and several additional cross-reference numbers. Installs in 20–30 minutes with basic hand tools. Quick Answer The 279838 Genuine OEM Whirlpool Dryer Heating Element fixes electric dryers that produce no heat, heat weakly, or take much longer than usual to dry clothes. 5400W / 240V, nickel-chromium coil, two 5/16" male terminals. Includes element coil with partial housing — reuses remaining outer housing from old assembly. Thermostat and thermal fuse not included. Replaces WP279837, 3398064, 3403585, 8565582, W10724237, 2438, AP3094254. Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef electric dryers. Common Problems This Part Fixes Dryer produces no heat at all — heating element coil has burned through Dryer takes much longer than normal to dry clothes Dryer tumbles normally but generates no heat during the cycle Visible break, burn spot, or separation in the heating coil inside the housing No continuity across the heating element terminals when tested with a multimeter Burning smell from the dryer — arcing at a weak spot in the coil Dryer trips the circuit breaker when the heat cycle is selected — shorted element Replaces Part Numbers This heating element directly replaces the following OEM and cross-reference part numbers: 279838, 279837, WP279837, 2438, 279838A, 279838VP, 3398063, 3398064, 3403585, 8565582, 4531017, 4617547, 4675511, 5324919, 5329098, 5895597, W10724237, AH334313, AWP39215, EA334313, EAP334313, FIX334313, AP3094254, PD00002351, PS334313. Contact our support team with your model number if you need confirmation before ordering. Compatibility This heating element is compatible with select electric dryers only from the following brands: Whirlpool electric dryers (WED, MEDC, MEDX, Duet, Cabrio series and more) Kenmore / Sears electric dryers — 110 series and Whirlpool-built models Maytag electric dryers (MEDC, MEDX, MED series) Amana electric dryers (NED series) KitchenAid electric dryers Roper electric dryers Crosley electric dryers Estate electric dryers Inglis electric dryers Admiral electric dryers Magic Chef electric dryers Note: This is for electric dryers only. Gas dryers use a gas burner assembly and do not have an electric heating element. Always verify your dryer type and model number before ordering. When replacing the heating element, it is strongly recommended to also replace the high-limit thermostat and thermal cut-off fuse (279973 kit) — a failed element is almost always associated with an overheating event that also stresses the thermal components. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Primary heat source for electric dryers — nickel-chromium resistance coil generates heat during every drying cycle Rated 5400W / 240V — correct wattage for compatible Whirlpool-family electric dryers Two 5/16" male terminals — matches the original terminal configuration for direct wire connection Includes heating element coil with partial housing and ceramic insulators pre-installed Reuses remaining outer housing from old assembly — partial housing replacement only Thermostat and thermal fuse not included — order 279973 kit separately if those also need replacement Replaces WP279837, 3398064, 3403585, 8565582, W10724237, 2438, and over 15 additional cross-reference numbers Compatible with 11 major appliance brands on the Whirlpool platform DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number 279838 Part Type Dryer Heating Element Assembly (Electric) Condition Genuine OEM Application Electric Dryers Only Wattage 5400W Voltage 240V AC Coil Material Nickel-chromium resistance wire Terminals Two 5/16" male terminals Includes Element coil with partial housing and ceramic insulators — reuses remaining outer housing Does Not Include Thermostat, thermal fuse — order 279973 kit separately Often Replaced With 279973 High-Limit Thermostat and Thermal Cut-Off Kit Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef Installation Notes ⚠️ Unplug Dryer Before Starting — Electric Dryers Only Disconnect power before beginning. Remove the back panel of the dryer by unscrewing the perimeter screws to access the heating element housing at the lower rear of the dryer. Photograph the wiring connections before disconnecting anything. Remove the two wire connections from the element terminals and the thermostat/thermal fuse wire connections from the housing. Unscrew the heating element housing from the dryer cabinet and slide the old assembly out. Remove the inner element frame from the outer housing — the outer housing is reused. Transfer the new 279838 element (which comes with a partial housing) into the existing outer housing. Reinstall the housing into the dryer, reconnect all wiring in the same positions as photographed, reinstall the back panel, restore power, and run a test heat cycle. Tip: while the element housing is removed, inspect the thermal fuse (3392519) and high-limit thermostat/cut-off kit (279973) and replace if needed. Tools needed: Phillips screwdriver, 1/4" nut driver. Frequently Asked Questions How do I test if the heating element has failed? Unplug the dryer and remove the back panel to access the heating element housing. Disconnect the two wire terminals from the element and set your multimeter to continuity or resistance mode. Probe both terminals. A working heating element will show a resistance reading — typically between 8 and 15 ohms for a 5400W/240V element. An open circuit (no continuity / infinite resistance) confirms the element coil has burned through at a break point. You can also visually inspect the coil inside the housing for a visible gap, burn spot, or sag in the wire — any break in the coil indicates a failed element. Does this element include the thermostat and thermal fuse? No — the 279838 includes the heating element coil and partial housing only. The high-limit thermostat and thermal cut-off fuse are separate parts that mount on the element housing and are not included. When replacing the heating element, it is strongly recommended to also replace these thermal components using the 279973 thermostat kit, as a burned-out element is almost always the result of an overheating condition that also stresses the thermostat and thermal cut-off. Replacing them together ensures the heating system is fully restored and reduces the chance of a repeat failure. Why does the 279838 only come with partial housing? The 279838 heating element is designed as a replacement for the inner coil and frame assembly only — it installs inside the existing outer housing from your old assembly. The outer housing is a steel shell that does not wear out and does not need to be replaced under normal circumstances. By including only the partial housing (inner frame and coil), Whirlpool reduces part cost and simplifies installation — you simply swap the new element into your existing outer housing rather than replacing the entire assembly. Will replacing the heating element fix my dryer if the thermal fuse is also blown? Not by itself. If the thermal fuse (3392519) has also blown — which is common when the heating element fails — replacing only the element will not restore heat because the blown fuse permanently interrupts the circuit. You will need to replace both the heating element and the thermal fuse to restore normal operation. Since a thermal fuse blows due to overheating, also replacing the high-limit thermostat and thermal cut-off kit (279973) at the same time is recommended to ensure complete thermal protection is in place. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element assembly installed in compatible Whirlpool, Kenmore, Maytag, and related brand electric dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Choice 240597203 Refrigerator Temperature Sensor Replaces 240597220 The Choice 240597203 is an aftermarket replacement refrigerator temperature sensor compatible with a wide range of Frigidaire, Electrolux, Kenmore (253/106/795 prefix), Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, and Ikea refrigerators and household freezers. This NTC (negative temperature coefficient) thermistor continuously monitors the temperature inside the refrigerator or freezer compartment and sends resistance-based readings to the main control board, which uses this data to cycle the compressor, fans, and defrost heaters to maintain accurate temperatures. As the thermistor heats up or cools down, its electrical resistance changes predictably, allowing the control board to calculate the exact temperature in real time. When this sensor fails or drifts out of range, the refrigerator may run too cold or too warm, cycle excessively, freeze up the evaporator, fail to maintain set temperatures, or display OP error codes. Rated 10K Ohm NTC, with a 5/16" diameter probe, 12" wire, and overall dimensions of 3-5/8"L x 5/8"W x 5/16"H (sensor probe itself measures ~1-3/16"L x 5/16" diameter). Compatible with 20-28 cubic foot North American household refrigerators in French door, side-by-side, top-freezer, and bottom-freezer configurations (post-2005 production). It directly replaces 240597203, 240597220, 240597201, 240597202, 7240597203, AP4032998, AH1765215, EA1765215, EAP1765215, EAP17647917, 1258948, 4985585, OEM21729470, PD00000590, PD00088922, PS1765215, and PS17647917. Not compatible with mini fridges, car refrigerators, commercial units, wine coolers, or ice makers. Installs in 15–20 minutes with basic hand tools. Quick Answer The Choice 240597203 Refrigerator Temperature Sensor fixes Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, and Ikea refrigerators that run too cold or warm, cycle excessively, freeze up the evaporator, or display OP error codes. NTC thermistor — 10K Ohm at room temperature. 5/16" probe diameter, 12" wire. Overall 3-5/8"L x 5/8"W x 5/16"H. Replaces 240597220, 240597201, 240597202, 7240597203, AP4032998, AH1765215, EA1765215, EAP1765215, EAP17647917, 1258948, 4985585, OEM21729470, PD00000590, PD00088922, PS1765215, PS17647917. For 20–28 cu ft household refrigerators built 2005 or later. Common Problems This Part Fixes Refrigerator running too cold or too warm — sensor not accurately reporting temperature Inconsistent temperatures — fluctuating cooling that can't maintain set point OP error code displayed on the control panel (open sensor circuit) Excessive frost or ice buildup on evaporator coils from erratic defrost timing Refrigerator running continuously without cycling off Freezer over-freezing food or fresh food compartment freezing groceries Food spoilage from temperature instability Multimeter test shows 0 ohms (shorted), infinite resistance (open), or drifted resistance instead of the expected ~10K Ohms at room temperature Replaces Part Numbers This temperature sensor directly replaces the following OEM and cross-reference part numbers: 240597220, 240597203, 240597201, 240597202, 7240597203, 4985585, AFR15666, AP7243155, EAP17647917, OEM21729474, PD00088922, PS17647917. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This temperature sensor is compatible with select household refrigerators and freezers from the following brands (20–28 cu ft, built 2005 or later): Frigidaire refrigerators — Gallery and Professional series, plus standard Frigidaire models (BFHS2611LM, BGHS2634KE, BGHS2634KP, BGHS2644KF, CRSH237LB, PRFG2383AF, PRFC2383AF, ERFG2393AS2, FRSS2323AS8, FFHB2740PP5A and many related models) Frigidaire upright freezers — FFFH21F7QW, FGU19F6QWB and related models Electrolux refrigerators — EI24RD65KS0, EI24RD65HS0, EI24RD65HS1, E24RD75KPS0 and related models Kenmore / Sears refrigerators — 253-prefix, 106-prefix, and 795-prefix models (select Frigidaire/Electrolux-built units) Crosley refrigerators (select Frigidaire-built models) White-Westinghouse refrigerators (select models) Kelvinator refrigerators (select models) Gibson refrigerators (select models) Tappan refrigerators (select models) Viking refrigerators (select Frigidaire-platform models) Ikea refrigerators (select Frigidaire-platform models) Not compatible with: mini fridges, car refrigerators, commercial refrigerators/freezers, wine coolers, or dedicated ice makers. Verify your refrigerator was produced after 2005 and check the original part number on the fridge nameplate matches one of the cross-references listed. Contact our support team with your model number if you're unsure. Key Features NTC (negative temperature coefficient) thermistor — resistance changes predictably with temperature, allowing precise temperature monitoring Rated 10K Ohms at room temperature (approximately 25°C / 77°F) Sends real-time temperature data to the main control board to regulate compressor cycling, fan operation, and defrost timing Sensor probe: 5/16" diameter x 1-3/16" length · Overall assembly: 3-5/8"L x 5/8"W x 5/16"H · 12" wire lead White plastic/metal construction with glossy finish Resolves OP error codes when caused by an open sensor circuit Compatible with 20–28 cu ft French door, side-by-side, top-freezer, and bottom-freezer refrigerators built 2005 or later Replaces 18+ OEM and cross-reference part numbers including 240597220, 240597201, 240597202, AP4032998, AH1765215, PS1765215, PS17647917 Compatible with Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, Ikea Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number 240597203CM Part Type Refrigerator Temperature Sensor (NTC Thermistor) Condition Aftermarket Replacement Application Household Refrigerators and Freezers (Frigidaire/Electrolux platform, 20–28 cu ft, 2005+) Sensor Type NTC (Negative Temperature Coefficient) Resistance 10K Ohms at room temperature Probe Dimensions 5/16" Diameter x 1-3/16" Length Overall Dimensions 3-5/8"L x 5/8"W x 5/16"H Wire Length 12" Color White Finish Glossy Material Plastic / Metal Error Codes Resolved OP (open sensor circuit) Compatible Brands Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, Ikea Installation Notes ⚠️ Unplug Refrigerator and Move Perishable Food Before Starting — Wear Work Gloves Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves to protect your hands. Depending on your refrigerator model, the fresh-food temperature sensor is typically located behind the air tower or damper assembly on the rear interior wall of the refrigerator compartment; the freezer temperature sensor is typically located behind the rear freezer access panel near the evaporator coils. Confirm which sensor location matches your symptom and the parts diagram for your specific model before starting. Remove all shelves, drawers, and any items blocking access to the sensor location. Remove the screws holding the air tower/damper cover (fresh food side) or rear freezer access panel to expose the sensor. Photograph the sensor position, wire routing, and connector before removing. Disconnect the wire connector (gently — the connector can be fragile) and release the sensor from its mounting clip. Fully insert the new 240597203 sensor probe into the card slot (no exposure) and secure with the mounting clip. Reconnect the wire connector — plug wiring terminals tightly to avoid poor contact. Use cable ties to secure any loose wire routing as before. Reinstall the cover or panel, replace the shelves and drawers, and plug the refrigerator back in. Allow several hours for the refrigerator to return to its set temperature before reloading with food. Tools needed: Phillips screwdriver, cable ties, multimeter (for testing), work gloves. Frequently Asked Questions What does OP error code mean on my Frigidaire refrigerator? The OP error code (Open) indicates the control board is detecting an open circuit on a temperature sensor input — meaning the sensor is failing to send a resistance signal, either because the sensor itself has failed open internally, the wire has broken, or the connector isn't seated. Replacing the temperature sensor typically resolves the code when the sensor itself is the cause. If the code persists after replacement, check the wire harness between the sensor and the control board for damage, and confirm the connector is fully seated. If the OP code appears alongside other symptoms like frost buildup and cooling issues that persist after sensor replacement, the defrost temperature sensor (on the Harness-Low Side, a different part number) may also need to be replaced, or the main control board may be at fault. How do I test if the temperature sensor has failed? Unplug the refrigerator, disconnect the sensor's wire connector, and set your multimeter to resistance mode. At room temperature (approximately 25°C / 77°F), a working NTC thermistor should read approximately 10K Ohms. If the sensor reads 0 ohms, it has shorted internally. If it reads infinite resistance (open circuit, often shown as "OL" on the multimeter), the sensor has failed open. If it reads significantly off from 10K (for example 8.4K or 5K at room temp), the sensor has drifted and is no longer providing accurate readings — replacement is recommended. Any of these results confirms the sensor needs replacement. My refrigerator has multiple temperature sensors — which one do I replace? Frigidaire refrigerators typically use multiple temperature sensors: one in the fresh food compartment (behind the air tower/damper), one in the freezer compartment (near the evaporator coils), and often a separate defrost temperature sensor on the Harness-Low Side. The 240597203 is used as the fresh food or freezer compartment temperature sensor. If your symptom is "fresh food too warm" or "freezer over-freezing," the fresh food sensor is the likely candidate. If your symptom is "freezer icing up despite defrost heater working," the defrost temperature sensor may be the culprit — a different part number. Check your refrigerator's parts diagram to confirm the correct sensor location for your specific symptom. Does this sensor fit my Kenmore refrigerator? On many Kenmore refrigerators, yes — Sears sells Kenmore-branded refrigerators that are manufactured by Frigidaire/Electrolux, Whirlpool, LG, and Samsung. The 240597203 sensor fits Kenmore refrigerators with model numbers beginning with the 253, 106, or 795 prefixes that are Frigidaire/Electrolux-built. Kenmore refrigerators built by other manufacturers (Whirlpool, LG, Samsung) use different sensors. Check the first three digits of your Kenmore model number — if it's 253, 106, or 795 and falls within the compatible model list, this is the correct part. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured to match the electrical specifications (10K Ohm NTC), probe dimensions (5/16" diameter x 1-3/16" length), wire length (12"), and connector configuration of the original 240597203 temperature sensor used in compatible refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WP3387749 Dryer Genuine OEM Heating Element – Compatible with Whirlpool, Kenmore, Maytag Dryers Product Description Restore your dryer’s heating performance with the WP3387749 Dryer Genuine OEM Heating Element. This factory-approved replacement part generates the heat needed to dry laundry efficiently. A failed heating element may cause your dryer to run but not heat, take longer to dry clothes, or shut down during cycles. Replacing it with this genuine OEM part ensures safe operation and long-lasting performance. Replaces Part Numbers WP3387749, 3387749, 525504, PD00003387, EAP344599, AP6008283, PS11741418. Compatibility This heating element is compatible with select Whirlpool, Kenmore, Maytag dryers. Example compatible models include (but are not limited to): Whirlpool LER4634EQ2, Kenmore 110.96573220, and Maytag MEDC215EW1. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Wide Compatibility – Fits Whirlpool, Kenmore, Maytag dryers 🔥 Restores Heating – Generates reliable, consistent heat for drying 💰 Cost-Effective OEM Repair – Genuine part ensures durability and performance 🛠️ DIY Friendly – Installs with standard tools in under 30 minutes 🛡️ Fixes Common Issues – Solves no-heat problems, long drying times, or mid-cycle shutdowns 📐 Product Specification Part Number: WP3387749 Component Type: Dryer Heating Element Material: High-temperature resistant metal coil with mounting housing Mounting: Direct replacement heating element assembly Operating Conditions: Designed for residential dryers Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Nut driver, Phillips screwdriver, needle-nose pliers ⚠️ Safety First: Always unplug the dryer before beginning repairs to prevent electrical shock. Steps: Disconnect power and remove dryer rear access panel. Locate the heating element housing inside the dryer. Disconnect wire terminals and remove screws securing the old element. Slide out defective element and install the new WP3387749. Reconnect wires, secure housing, and reinstall rear panel. Restore power and test dryer heating. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Get your dryer heating again — Add to Cart Now for a safe, factory-approved repair! WP3387749 Dryer Genuine OEM Heating Element Cross Reference Information   Part Number WP3387749, 3387749, 525504, PD00003387, EAP344599, AP6008283, PS11741418.

Read more less

DA32-00006W Genuine Samsung OEM Refrigerator Thermistor Refrigerator defrost temperature sensor. Replaces Part Numbers: DA32-10105R, DA32-00006W, DA32-00006U, 2030342, DA32-00006B, DA32-00006C, DA32-00006D, DA32-00006L, DA32-00006M, DA32-00006T, DA32-00006V, AP4135567, PS4138681. The Samsung Defrost Sensor is a genuine part designed specifically for Samsung refrigerators. This sensor, sometimes referred to as a defrost thermostat or defrost temperature sensor, is an integral part of your refrigerator's defrost system.  

Read more less

XPARTCO W10900067 Dryer Thermal Cut-Off Fuse & Thermostat Kit – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Restore safe and reliable dryer heating with the XPARTCO W10900067 Dryer Thermal Cut-Off Fuse & Thermostat Kit. This cut-off terminal is a replacement Part for specific Kenmore, Maytag, Roper, Whirlpool dryer models. The kit contains a 309°F Thermal Cut-Off Fuse and a high limit thermostat. In electric dryers, it shuts off the heat if overheating occurs to prevent fire risk. The thermal fuse cuts power while the thermostat regulates the operating temperature. To install, first, unplug the dryer. Use a multimeter to test the old fuse for continuity at room temperature; it should read zero ohms. XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers W10900067, 4460718, N197, 197CM, 197, PD00046493, EAP11769432, AP6036100, PS11769432. Compatibility This replacement dryer thermal cut-off fuse and thermostat kit fits select Whirlpool, Maytag, Kenmore, Amana, Estate, Roper, and Crosley electric dryers. Example compatible models include (but are not limited to): Whirlpool WED4800XQ, WED4815EW1 Maytag MEDC215EW1 Kenmore 110.6012010 Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement Kit – Matches OEM temperature and safety specifications 🌡️ Accurate Heat Protection – Helps regulate dryer temperature safely 🔥 Overheat Safety Cut-Off – Prevents damage caused by excessive heat 💰 Cost-Effective Repair – Reliable alternative to higher-priced OEM kits 🛡️ Fixes Common Issues – Resolves no heat, overheating, and thermal shutdowns 📐 Product Specification Part Number: W10900067 Component Type: Dryer Thermal Cut-Off Fuse & Thermostat Kit Includes: Thermal cut-off fuse and high-limit thermostat Application: Heater housing / exhaust temperature control Material: Heat-resistant metal housings Mounting: Screw-mounted Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to avoid electrical shock. Basic Steps: Disconnect dryer power. Remove the rear access panel. Locate the thermal cut-off and thermostat on the heater housing. Disconnect wiring and remove old components. Install the new XPARTCO W10900067 components in the same positions. Reconnect wiring, reinstall panel, and restore power. Run a test cycle to confirm proper heating. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore safe dryer heating and protection — Add to Cart Now for a dependable, budget-friendly repair!

Read more less