Search results for "Microwave Bulb"

XPARTCO WE05X20431 Dryer Light Bulb The XPARTCO WE05X20431 is an aftermarket replacement drum light bulb for GE, Hotpoint, Whirlpool, and Kenmore dryers. Also called a drum lamp, this small bulb mounts inside the dryer cabinet and illuminates the drum whenever the door is opened, making it easy to spot small items and confirm the drum is fully empty before starting a new load. It's a simple part, but when it burns out it's easy to notice — you open the door and the interior stays dark. Rated 10W at 120V with an E12 (candelabra) base, measuring approximately 1-5/8"H x 5/8"W x 5/8"D. Like any incandescent bulb, it will eventually burn out from normal use and the heat it's exposed to inside a working dryer. It directly replaces WE4M305, WE4X718, WE04X718, WE04X0718, WE04M0305, AP3794707, AP5956400, 1063664, AH960329, EA960329, PS960329, and PS10063224. Quick Answer The XPARTCO WE05X20431 Dryer Light Bulb fixes GE, Hotpoint, Whirlpool, and Kenmore dryers where the interior drum light doesn't turn on when the door is opened. 10W, 120V, E12 base. Replaces WE4M305, WE4X718, WE04X718, WE04X0718, WE04M0305, AP3794707, AP5956400, 1063664, AH960329, EA960329, PS960329, PS10063224. No tools required — the bulb installs at a slight angle, not straight in. Common Problems This Part Fixes Dryer drum light doesn't turn on when the door is opened Interior lighting is dim, flickering, or inconsistent Bulb has visibly burned out or gone dark Difficulty seeing small items left in the drum before starting a load Light worked before but stopped after normal use over time Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer light bulb directly replaces the following OEM and cross-reference part numbers: WE05X20431, WE4M305, WE4X718, WE04X718, WE04X0718, WE04M0305, AP3794707, AP5956400, 1063664, EAP10063224, PS10063224, AGE25386, PD00028741 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum light bulb is compatible with select GE and Hotpoint dryers, and also fits select Whirlpool and Kenmore dryers using the same E12-base bulb, including model numbers such as GTD42EASJ2WW and DCVH680GJ2MS. Note: Always verify your full model number before ordering, since dryer light bulbs vary in base type and wattage across different platforms. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement drum light bulb — illuminates the dryer interior when the door is opened Resolves "light doesn't turn on," "dim or flickering light," and "burned-out bulb" symptoms 10W, 120V, E12 (candelabra) base Compact size: approximately 1-5/8"H x 5/8"W x 5/8"D Built to withstand the heat and vibration of normal dryer operation No tools required — simple screw-in installation Replaces WE4M305, WE4X718, WE04X718, WE04X0718, WE04M0305, AP3794707, AP5956400, 1063664, AH960329, EA960329, PS960329, and PS10063224 Compatible with GE, Hotpoint, Whirlpool, and Kenmore dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number WE05X20431 OEM Part Number WE05X20431 Part Type Dryer Drum Light Bulb (Drum Lamp) Condition Aftermarket Replacement Wattage 10 W Voltage 120V Base Type E12 (candelabra) Dimensions 1-5/8"H x 5/8"W x 5/8"D Repair Difficulty Very Easy — no tools required Quantity 1 bulb Compatible Brands GE, Hotpoint, Whirlpool, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Let The Old Bulb Cool First Disconnect power at the outlet or shut off the circuit breaker before beginning. If the dryer was recently run, allow the bulb to cool before touching it. Locate the light fixture inside the top section of the dryer interior. Unscrew the old bulb by turning it three to four turns to release it from the socket. When installing the new bulb, it cannot be screwed straight in — lean it at roughly a 45-degree angle to engage the socket threads, then turn it to seat and tighten. Avoid touching the glass directly with bare fingers if possible, since oils can shorten bulb life. Restore power and open the dryer door to confirm the light turns on. Tools needed: none. Frequently Asked Questions Why won't the new bulb screw in straight? This is normal for this fixture — the socket is angled, so the bulb needs to go in at roughly a 45-degree tilt to catch the threads properly rather than straight on. Once you find that angle, it threads in and seats normally. Do I need any tools to replace this bulb? No. This is a simple screw-in bulb replacement with no tools required — just unplug the dryer, unscrew the old bulb, and screw in the new one at the correct angle. The light still doesn't work after I replaced the bulb. What else could it be? If a new bulb doesn't resolve the issue, check the door switch that controls the light circuit, and confirm the socket and wiring aren't damaged. These are separate components from the bulb itself and would need to be diagnosed independently. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the wattage, voltage, base type, and dimensions of the original WE05X20431 bulb used in compatible GE, Hotpoint, Whirlpool, and Kenmore dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WG447 Microwave Mica Sheet, Waveguide Cover – Compatible with Whirlpool, GE, Samsung, LG, Panasonic, and More Product Description Protect your microwave’s internal components with the WG447 Microwave Mica Sheet / Waveguide Cover. Microwave mica chips can effectively prevent water or oil and other substances from splashing on the magnetron or other components during the heating process of food. Protect the microwave oven from burning. Size can be cut: The waveguide cover size is 10 cm*10.8 cm (3.93 in x 4.65 in), you could cut it into any size to fit your microwave oven. Easy to cut. Widely used: As a kind of heat resisting and insulating product. Mica Plates is widely used in household appliances such as hair dryers, toasters, microwave ovens, warmers, etc.  Replaces Part Numbers universal microwave mica sheet equivalents. Size can be cut: The waveguide cover size is 10 cm*10.8 cm (3.93 in x 4.65 in), you could cut it into any size to fit your microwave oven. Easy to cut.   Compatibility This replacement waveguide cover fits a wide range of Whirlpool, GE, Samsung, LG, Panasonic, Emerson, Sharp, Kenmore, and other microwaves that use a cut-to-fit mica sheet. Common compatible models include (but are not limited to):Whirlpool WMH31017HS, GE JVM3160RFSS, Samsung ME18H704SFS, LG LMV1762ST, Panasonic NN-SN766S. Always compare dimensions before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Universal cut-to-fit design matches OEM insulation and heat resistance ⚡ Restores Safe Operation – Prevents arcing, sparking, and microwave energy leakage 🔥 Heat & Moisture Resistant – Made from high-grade mica composite ✂️ Easy to Trim – Can be cut to match original waveguide cover size 🛡️ Fixes Common Issues – Solves sparking, burning smell, and uneven heating caused by damaged covers 📐 Product Specification Part Number: WG447 Component Type: Microwave Mica Sheet / Waveguide Cover Material: Heat-resistant mica composite Dimensions: Approx. 6" × 6" (can be trimmed to size) Thickness: Standard 0.3–0.4 mm mica sheet Mounting: Press-fit or screw-secured depending on model Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Scissors or utility knife (for trimming), screwdriver (if applicable) ⚠️ Safety First: Always unplug the microwave before servicing. Do not operate the microwave without a waveguide cover. Steps: Disconnect power and remove the old burned or damaged mica cover. Use the old cover as a template to trim the new WG447 mica sheet. Align the new cover over the waveguide opening. Press into clips or secure with screws depending on your model. Restore power and test heating performance. ⏱️ Time Required: 5–10 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Stop microwave sparking and restore safe heating — Add to Cart Now for a quick, reliable fix!

Read more less

4 Pack - XPARTCO EXP480 Microwave Door Switch (NC - NO) Normally Closed / Open The XPARTCO EXP480 is a universal replacement door interlock switch for microwave ovens and microwave/oven combination units. This is a critical safety component: microwave door interlock switches exist specifically to cut power to the magnetron the instant the door opens, preventing any possibility of microwave radiation escaping the cavity while the door isn't fully closed and latched. This switch combines both a normally closed (NC) and normally open (NO) contact set in a single body, matching the dual-contact design used across a wide range of microwave door latch mechanisms. Rated 16A maximum current, 250VAC maximum voltage, with an IP40 protection rating. Over time, these switch contacts can wear, pit, or fuse together from repeated cycling and the electrical load they carry every time the door opens and closes. A failing interlock switch typically shows up as a microwave that won't start at all, a display that works but the unit won't heat, or in less common but more serious cases, a switch that has fused shut and continues carrying current even when it shouldn't. It directly replaces 28QBP0496, W10211972, 4375346, W10330566, WPW10330566, 1472224, 4393442, 4393498, 4393570, 4393697, 4393881, 461967848881, 8206345, W10131248, W10217468, AH2338920, EA2338920, AP4357880, PS2338920, KW3A-16Z0-A200-76, W10727360, W10269457, 3379124, AP5950105, and PS10057151. Quick Answer The XPARTCO EXP480 Microwave Door Switch (NC - NO) fixes microwave ovens and microwave/oven combos that won't start, won't heat, or have a door latch mechanism that isn't reliably cutting power when the door opens. 16A, 250VAC, combined NC/NO contact design. Replaces 28QBP0496, W10211972, 4375346, W10330566, WPW10330566, 1472224, 4393442, 4393498, 4393570, 4393697, 4393881, 461967848881, 8206345, W10131248, W10217468, AH2338920, EA2338920, AP4357880, PS2338920, KW3A-16Z0-A200-76, W10727360, W10269457, 3379124, AP5950105, PS10057151. Never operate a microwave with a bypassed, disconnected, or suspected-faulty door interlock switch — these switches exist to prevent radiation exposure and must always be replaced with a properly rated part, never removed or defeated. Common Problems This Part Fixes Microwave won't start at all, even though the display and buttons respond normally Microwave display and timer work, but the unit won't heat Microwave stops working intermittently, especially around the door latch Clicking or buzzing sound from the door area without the microwave starting Breaker tripping when the door is opened, indicating a switch contact that has fused shut Door that doesn't feel like it's latching securely Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This microwave door switch directly replaces the following OEM and cross-reference part numbers: 28QBP0496, W10211972, 4375346, W10330566, WPW10330566, 1472224, 4393442, 4393498, 4393570, 4393697, 4393881, 461967848881, 8206345, W10131248, W10217468, AH2338920, EA2338920, AP4357880, PS2338920, W10727360, W10269457, 3379124, AP5950105, PS10057151 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is a universal replacement compatible with convection microwave ovens, grill microwave ovens, microwave/oven combination units, and solo microwave ovens across many brands, wherever the original switch matches this NC/NO contact configuration and electrical rating. Note: Microwave door interlock systems typically use two or three separate switches working together (primary interlock, monitor/secondary switch, and sometimes a third safety switch), and not all of them share this same NC/NO configuration. Confirm which specific switch position has failed on your microwave, and match the contact configuration and electrical rating exactly — never substitute a switch with a different configuration. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which switch your microwave needs. Key Features Universal replacement microwave door interlock switch — combined NC (normally closed) and NO (normally open) contact design Resolves "won't start," "won't heat," and "intermittent operation near the door latch" symptoms caused by switch failure Rated 16A, 250VAC maximum IP40 protection rating Safety approved: CCC, CE, UL, VDE Suitable for convection, grill, combination, and solo microwave ovens Direct drop-in replacement matching the original mounting and terminal configuration Replaces a wide range of OEM part numbers across Whirlpool, GE, and related platforms — see full list above Built to OEM-equivalent quality standards Product Specifications Part Number EXP480 Part Type Microwave Door Interlock Switch (NC/NO Combination) Condition New — Universal Replacement Part Contact Configuration Normally Closed (NC) + Normally Open (NO) Max. Current 16A Max. Voltage 250VAC Operating Temperature -25°C to +85°C Protection Degree IP40 Contact Form SPDT Terminal Size 6.3mm (approx. 1/4") Operating Force 25g (0.245N) – 400g (3.92N) Material Plastic Color Gray Safety Approvals CCC, CE, UL, VDE Application Convection, Grill, Combination, and Solo Microwave Ovens Installation Notes ⚠️ Danger — Never Bypass A Door Interlock Switch Unplug the microwave before beginning any work, and if it's a built-in or over-the-range unit, shut off power at the breaker as well. Microwave ovens also contain a high-voltage capacitor that can retain a dangerous electrical charge even after the unit is unplugged — avoid touching internal components near the capacitor and magnetron. Door interlock switches are a critical safety system: they exist specifically to cut power the instant the door opens, preventing microwave radiation from escaping the cavity. Never operate a microwave with an interlock switch disconnected, bypassed, or jumpered, even temporarily — doing so can expose you and others to microwave radiation. If you are not fully comfortable working inside a microwave's internal compartment, have a qualified appliance technician perform this repair instead. ⚠️ Photograph Wiring Before Disconnecting — Match The Failed Switch Exactly Wear work gloves. Remove the outer cabinet or access panel per your model's service instructions to reach the door switch assembly, typically located near the door latch mechanism. Photograph the wiring on the old switch before disconnecting anything, and confirm you're replacing the correct switch position if your microwave uses multiple interlock switches. Disconnect the wire terminals from the old switch, remove its mounting screws, and pull it free. Install the new EXP480 in the same position, reconnect each wire terminal to its original position, and secure the mounting screws. Reinstall the cabinet or access panel. Restore power and test that the microwave starts normally with the door closed, and — this is the critical safety check — confirm the unit stops heating immediately when the door is opened during a test run with a cup of water. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My microwave stopped working. How do I know if it's actually a door switch and not something else? A common pattern is a microwave where the display and buttons respond normally, but pressing start does nothing, or the unit hums without heating — this points toward the door interlock circuit rather than the control board. Since these switches also serve a critical safety function, if you suspect a fault in this area, it's best to have it properly diagnosed and replaced rather than working around the symptom. Is it safe to just disconnect a faulty interlock switch so the microwave will run? No — this is not safe under any circumstances. Door interlock switches exist specifically to cut power to the magnetron the instant the door opens, preventing microwave radiation from escaping. Bypassing, disconnecting, or jumpering one of these switches removes that protection and can expose you and anyone nearby to microwave radiation, even if the microwave otherwise appears to run normally. Always replace a faulty switch with a correctly rated new one rather than working around it. My microwave trips the breaker whenever I open the door. What does that mean? This can indicate that one of the door switches — often the one that should open when the door opens — has fused or welded its contacts shut from repeated electrical stress, so it continues carrying current when it shouldn't. This is a genuine safety concern and the affected switch should be replaced promptly rather than continuing to use the microwave. My microwave uses more than one door switch. How do I know which one to replace? Most microwaves use two or three separate interlock switches working together, and they don't always share the same contact configuration. Check your appliance's parts diagram or the physical switch you're replacing to confirm it matches this NC/NO combination design before ordering, and always test or verify function with a multimeter if you're uncertain which specific switch has failed. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WR55X11132 Refrigerator LED Light Product Overview The XPARTCO WR55X11132 Refrigerator LED Light provides bright, energy-efficient illumination inside your refrigerator, improving visibility and enhancing overall appliance functionality. This high-quality LED module restores clear lighting for easy food access. Note: This is LED Light only, Cover is not included. Quick Answer If your refrigerator light is dim, flickering, or not turning on, the WR55X11132 LED light module may be faulty. Replacing it restores proper interior lighting and visibility. Replaces Part Numbers Replaces OEM part number: WR55X11132, EAP4704284, AGE28811, PD00030062, AP5646375, 3033142, PS4704284. Compatibility This refrigerator LED light is compatible with select GE, Hotpoint, and GE Profile refrigerators. . GE Refrigerators: GFE26GGHBBB, GFE26GGHBWW, GFE26GGHCBB, GFE26GGHCWW, GFE26GGHDBB, GFE26GGHDWW, GFE26GGHEBB, GFE26GGHEWW, GFE26GGHFBB, GFE26GGHFWW, GFE26GGHGBB, GFE26GGHGWW, GFE26GGKBBB, GFE26GGKBWW, GFE26GMHBES, GFE26GMHCES, GFE26GMHDES, GFE26GMHEES, GFE26GMHGES, GFE26GMKBES, GFE26GSHBSS, GFE26GSHCSS. Always verify your appliance model number before ordering. Common Problems This Part Fixes Refrigerator light not working Dim or flickering LED light Poor visibility inside fridge Key Features Bright LED illumination Energy-efficient lighting Long-lasting performance High-quality aftermarket replacement Product Specifications Part Number: XPWR55X11132 Part Type: Refrigerator LED Light Module Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Refrigerator Interior Lighting Troubleshooting Guide No interior light → Failed LED module Flickering light → Failing LED board Dim lighting → Aging LED unit When Should You Replace This Light? Replace this LED light if your refrigerator interior lighting is not functioning properly or has become dim or inconsistent. Installation Notes ⚠️ Disconnect power before installation. Remove the light cover, disconnect the module, and install the new LED light securely. Related Parts Refrigerator Door Switch Control Board Light Cover Frequently Asked Questions Will this light fit my refrigerator?This LED module fits many GE and compatible models. Always verify your model number. Is this LED or bulb type?This is an LED light module, not a traditional bulb. What are signs of a bad LED module?No light, flickering, or dim lighting indicate replacement is needed. Is installation difficult?Most modules are easy to replace, but follow your appliance manual for best results. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support  

Read more less

XPARTCO EXP480 Microwave Door Switch (NC - NO) Normally Closed / Open The XPARTCO EXP480 is a universal replacement door interlock switch for microwave ovens and microwave/oven combination units. This is a critical safety component: microwave door interlock switches exist specifically to cut power to the magnetron the instant the door opens, preventing any possibility of microwave radiation escaping the cavity while the door isn't fully closed and latched. This switch combines both a normally closed (NC) and normally open (NO) contact set in a single body, matching the dual-contact design used across a wide range of microwave door latch mechanisms. Rated 16A maximum current, 250VAC maximum voltage, with an IP40 protection rating. Over time, these switch contacts can wear, pit, or fuse together from repeated cycling and the electrical load they carry every time the door opens and closes. A failing interlock switch typically shows up as a microwave that won't start at all, a display that works but the unit won't heat, or in less common but more serious cases, a switch that has fused shut and continues carrying current even when it shouldn't. It directly replaces 28QBP0496, W10211972, 4375346, W10330566, WPW10330566, 1472224, 4393442, 4393498, 4393570, 4393697, 4393881, 461967848881, 8206345, W10131248, W10217468, AH2338920, EA2338920, AP4357880, PS2338920, KW3A-16Z0-A200-76, W10727360, W10269457, 3379124, AP5950105, and PS10057151. Quick Answer The XPARTCO EXP480 Microwave Door Switch (NC - NO) fixes microwave ovens and microwave/oven combos that won't start, won't heat, or have a door latch mechanism that isn't reliably cutting power when the door opens. 16A, 250VAC, combined NC/NO contact design. Replaces 28QBP0496, W10211972, 4375346, W10330566, WPW10330566, 1472224, 4393442, 4393498, 4393570, 4393697, 4393881, 461967848881, 8206345, W10131248, W10217468, AH2338920, EA2338920, AP4357880, PS2338920, KW3A-16Z0-A200-76, W10727360, W10269457, 3379124, AP5950105, PS10057151. Never operate a microwave with a bypassed, disconnected, or suspected-faulty door interlock switch — these switches exist to prevent radiation exposure and must always be replaced with a properly rated part, never removed or defeated. Common Problems This Part Fixes Microwave won't start at all, even though the display and buttons respond normally Microwave display and timer work, but the unit won't heat Microwave stops working intermittently, especially around the door latch Clicking or buzzing sound from the door area without the microwave starting Breaker tripping when the door is opened, indicating a switch contact that has fused shut Door that doesn't feel like it's latching securely Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This microwave door switch directly replaces the following OEM and cross-reference part numbers: 28QBP0496, W10211972, 4375346, W10330566, WPW10330566, 1472224, 4393442, 4393498, 4393570, 4393697, 4393881, 461967848881, 8206345, W10131248, W10217468, AH2338920, EA2338920, AP4357880, PS2338920, W10727360, W10269457, 3379124, AP5950105, PS10057151 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is a universal replacement compatible with convection microwave ovens, grill microwave ovens, microwave/oven combination units, and solo microwave ovens across many brands, wherever the original switch matches this NC/NO contact configuration and electrical rating. Note: Microwave door interlock systems typically use two or three separate switches working together (primary interlock, monitor/secondary switch, and sometimes a third safety switch), and not all of them share this same NC/NO configuration. Confirm which specific switch position has failed on your microwave, and match the contact configuration and electrical rating exactly — never substitute a switch with a different configuration. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which switch your microwave needs. Key Features Universal replacement microwave door interlock switch — combined NC (normally closed) and NO (normally open) contact design Resolves "won't start," "won't heat," and "intermittent operation near the door latch" symptoms caused by switch failure Rated 16A, 250VAC maximum IP40 protection rating Safety approved: CCC, CE, UL, VDE Suitable for convection, grill, combination, and solo microwave ovens Direct drop-in replacement matching the original mounting and terminal configuration Replaces a wide range of OEM part numbers across Whirlpool, GE, and related platforms — see full list above Built to OEM-equivalent quality standards Product Specifications Part Number EXP480 Part Type Microwave Door Interlock Switch (NC/NO Combination) Condition New — Universal Replacement Part Contact Configuration Normally Closed (NC) + Normally Open (NO) Max. Current 16A Max. Voltage 250VAC Operating Temperature -25°C to +85°C Protection Degree IP40 Contact Form SPDT Terminal Size 6.3mm (approx. 1/4") Operating Force 25g (0.245N) – 400g (3.92N) Material Plastic Color Gray Safety Approvals CCC, CE, UL, VDE Application Convection, Grill, Combination, and Solo Microwave Ovens Quantity 1 door interlock switch Installation Notes ⚠️ Danger — Never Bypass A Door Interlock Switch Unplug the microwave before beginning any work, and if it's a built-in or over-the-range unit, shut off power at the breaker as well. Microwave ovens also contain a high-voltage capacitor that can retain a dangerous electrical charge even after the unit is unplugged — avoid touching internal components near the capacitor and magnetron. Door interlock switches are a critical safety system: they exist specifically to cut power the instant the door opens, preventing microwave radiation from escaping the cavity. Never operate a microwave with an interlock switch disconnected, bypassed, or jumpered, even temporarily — doing so can expose you and others to microwave radiation. If you are not fully comfortable working inside a microwave's internal compartment, have a qualified appliance technician perform this repair instead. ⚠️ Photograph Wiring Before Disconnecting — Match The Failed Switch Exactly Wear work gloves. Remove the outer cabinet or access panel per your model's service instructions to reach the door switch assembly, typically located near the door latch mechanism. Photograph the wiring on the old switch before disconnecting anything, and confirm you're replacing the correct switch position if your microwave uses multiple interlock switches. Disconnect the wire terminals from the old switch, remove its mounting screws, and pull it free. Install the new EXP480 in the same position, reconnect each wire terminal to its original position, and secure the mounting screws. Reinstall the cabinet or access panel. Restore power and test that the microwave starts normally with the door closed, and — this is the critical safety check — confirm the unit stops heating immediately when the door is opened during a test run with a cup of water. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My microwave stopped working. How do I know if it's actually a door switch and not something else? A common pattern is a microwave where the display and buttons respond normally, but pressing start does nothing, or the unit hums without heating — this points toward the door interlock circuit rather than the control board. Since these switches also serve a critical safety function, if you suspect a fault in this area, it's best to have it properly diagnosed and replaced rather than working around the symptom. Is it safe to just disconnect a faulty interlock switch so the microwave will run? No — this is not safe under any circumstances. Door interlock switches exist specifically to cut power to the magnetron the instant the door opens, preventing microwave radiation from escaping. Bypassing, disconnecting, or jumpering one of these switches removes that protection and can expose you and anyone nearby to microwave radiation, even if the microwave otherwise appears to run normally. Always replace a faulty switch with a correctly rated new one rather than working around it. My microwave trips the breaker whenever I open the door. What does that mean? This can indicate that one of the door switches — often the one that should open when the door opens — has fused or welded its contacts shut from repeated electrical stress, so it continues carrying current when it shouldn't. This is a genuine safety concern and the affected switch should be replaced promptly rather than continuing to use the microwave. My microwave uses more than one door switch. How do I know which one to replace? Most microwaves use two or three separate interlock switches working together, and they don't always share the same contact configuration. Check your appliance's parts diagram or the physical switch you're replacing to confirm it matches this NC/NO combination design before ordering, and always test or verify function with a multimeter if you're uncertain which specific switch has failed. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WR55X11132 Refrigerator LED Light Product Overview The XPARTCO WR55X11132 Refrigerator LED Light provides bright, energy-efficient illumination inside your refrigerator, improving visibility and enhancing overall appliance functionality. This high-quality LED module restores clear lighting for easy food access. Note: This is LED Light only, Cover is not included. Quick Answer If your refrigerator light is dim, flickering, or not turning on, the WR55X11132 LED light module may be faulty. Replacing it restores proper interior lighting and visibility. Replaces Part Numbers Replaces OEM part number: WR55X11132, EAP4704284, AGE28811, PD00030062, AP5646375, 3033142, PS4704284. Compatibility This refrigerator LED light is compatible with select GE, Hotpoint, and GE Profile refrigerators. . GE Refrigerators: GFE26GGHBBB, GFE26GGHBWW, GFE26GGHCBB, GFE26GGHCWW, GFE26GGHDBB, GFE26GGHDWW, GFE26GGHEBB, GFE26GGHEWW, GFE26GGHFBB, GFE26GGHFWW, GFE26GGHGBB, GFE26GGHGWW, GFE26GGKBBB, GFE26GGKBWW, GFE26GMHBES, GFE26GMHCES, GFE26GMHDES, GFE26GMHEES, GFE26GMHGES, GFE26GMKBES, GFE26GSHBSS, GFE26GSHCSS. Always verify your appliance model number before ordering. Common Problems This Part Fixes Refrigerator light not working Dim or flickering LED light Poor visibility inside fridge Key Features Bright LED illumination Energy-efficient lighting Long-lasting performance High-quality aftermarket replacement Product Specifications Part Number: XPWR55X11132 Part Type: Refrigerator LED Light Module Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Refrigerator Interior Lighting Troubleshooting Guide No interior light → Failed LED module Flickering light → Failing LED board Dim lighting → Aging LED unit When Should You Replace This Light? Replace this LED light if your refrigerator interior lighting is not functioning properly or has become dim or inconsistent. Installation Notes ⚠️ Disconnect power before installation. Remove the light cover, disconnect the module, and install the new LED light securely. Related Parts Refrigerator Door Switch Control Board Light Cover Frequently Asked Questions Will this light fit my refrigerator?This LED module fits many GE and compatible models. Always verify your model number. Is this LED or bulb type?This is an LED light module, not a traditional bulb. What are signs of a bad LED module?No light, flickering, or dim lighting indicate replacement is needed. Is installation difficult?Most modules are easy to replace, but follow your appliance manual for best results. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support  

Read more less

XPARTCO W11130208 Refrigerator LED Light Module for W11683241 The XPARTCO W11130208 is an aftermarket replacement LED light module for Whirlpool, KitchenAid, and Kenmore Elite refrigerators. W11130208 has been officially superseded by Whirlpool's current part number, W11683241 — the two are the same lighting solution across production revisions, so this listing ships as the current W11683241 service kit and will correctly replace an original W11130208 module. These modules attach inside the cabinet and illuminate the refrigerator or freezer compartment with efficient LED lighting. Rated 6V, these modules are wired in a series circuit — multiple modules connected end to end along a light strip. That series design has an important consequence for diagnosis: most "LED failures" that look like a complete lighting outage are actually just one burnt-out module dragging down the entire chain, not every module failing at once. A pigtail extension on the current kit design specifically addresses the most common DIY complaint with this repair — not being able to reach the connector behind the housing. Symptoms include dim or flickering lights, partial lighting where part of the compartment goes dark while the rest stays lit, or lights that don't turn on at all. It directly replaces AP7216885, W10279030, W10412708, W10623956, W10637153, WPW10637153, W10758333, W10876279, and W11203918. Quick Answer The XPARTCO W11130208 Refrigerator LED Light Module fixes Whirlpool, KitchenAid, and Kenmore Elite refrigerators with dim or flickering lights, partial lighting (part of the compartment dark while the rest stays lit), or lights that don't turn on at all. 6V modules, series circuit. Replaces AP7216885, W10279030, W10412708, W10623956, W10637153, WPW10637153, W10758333, W10876279, W11203918. This part number has been officially superseded by W11683241 — this listing ships as the current, direct-fit replacement. Common Problems This Part Fixes Refrigerator or freezer lights are dim or flickering Part of the compartment is dark while the rest of the light strip still works Lights don't turn on at all when the door is opened Lighting that has gradually dimmed over time One section of the light strip out while the remaining sections work normally Inconsistent lighting that flickers intermittently rather than staying steady Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator LED light module directly replaces the following OEM and cross-reference part numbers: W11130208, W10758333, W10412708, W10279030, W10637153, W10876279, AP6262381, PS12347525, Single Light used in Kit W11683241, 4591417, 4982094, AP6262381, AP7216885, EAP17216451, EAP6262381, PS12347525, PS17216451, AWP46249, PD00084706 W11130208 is the earlier Whirlpool number for this part; W11683241 is the current part number. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This LED light module is compatible with select Whirlpool refrigerators, and also fits select KitchenAid and Kenmore Elite refrigerators built on the same platform, including model numbers such as: Whirlpool: WRX988SIBM01, WRX988SIBW00, WRS973CIDM00, WRF991BOOM01, WRF989SDAM02, WRS965CIAM01, WRS965CIAE00 KitchenAid: KFIV29PCMS02, KRSC500ESS01, KRSF505EBL01, KRSF505ESS01, KRSF505EWH01 Kenmore: 10651173310, 10651762511, 10651763511, 10651764511, 10651769512, 59672389411 Note: This part is model-specific, not universal — several visually similar LED module kits exist across the Whirlpool lineup (including W11483116 and W10843353/W10695459 for other model groups) with different cross-reference sets. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which module fits your refrigerator. Key Features Aftermarket replacement LED light module — illuminates the refrigerator or freezer interior Ships as the current W11683241 kit, the official replacement for the superseded W11130208 number Resolves "dim or flickering lights," "partial lighting," and "lights won't turn on" symptoms Rated 6V, wired in a series circuit Pigtail extension design for easier access to the connector behind the housing Pop-out, plug-in module replacement — no screwdriver or wire nuts needed for the module swap itself Replaces AP7216885, W10279030, W10412708, W10623956, W10637153, WPW10637153, W10758333, W10876279, and W11203918 Compatible with Whirlpool, KitchenAid, and Kenmore Elite refrigerators Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number W11130208 OEM Part Number W11130208 Part Type Refrigerator LED Light Module Condition Aftermarket Replacement Voltage 6V Circuit Type Series (multiple modules per strip) Supersedes Current part number is W11683241 (same solution, current revision) Connector Design Pigtail extension for easier housing access Repair Difficulty Medium — 30 to 60 minutes Compatible Brands Whirlpool, KitchenAid, Kenmore Elite Installation Notes ⚠️ Unplug Refrigerator Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Locate the light housing panel inside the refrigerator or freezer compartment where the dim, flickering, or dark section is located, and remove it to access the module strip — this typically requires basic hand tools depending on your model. Identify the specific module that has failed; a burnt-out module in the middle of the strip can cause everything downstream of it to go dark or dim, even though only that one module has actually failed. Pop the old module out of its housing and unplug its connector — the pigtail extension design makes it easier to reach this connector without fully disassembling the housing. Plug in the new module and press it back into the housing in the same position. Reinstall the housing panel, restore power, and open the door to confirm even, consistent lighting has been restored across the full strip. Tools needed: basic hand tools for housing access (model-dependent), work gloves. Frequently Asked Questions I ordered W11130208 but received a module marked W11683241. Is that correct? Yes. W11130208 has been officially superseded by Whirlpool's current part number, W11683241 — they are the same lighting solution across production revisions, and W11683241 is what currently ships when this part is ordered. It installs and functions identically to the original W11130208. Only part of my fridge light strip is dark. Do I need to replace the whole strip? Not necessarily. These modules are wired in a series circuit, meaning several modules connect end to end along one strip. A single burnt-out module can cause everything downstream of it in that chain to go dark or dim, even though the rest of the modules are still perfectly good. In many cases, replacing just the failed module restores lighting to the whole strip rather than needing to replace every module. I can't reach the connector behind the light housing. Is that normal? This is a very common complaint with earlier module designs, and it's specifically what the pigtail extension on the current kit is designed to solve — it gives you more reach to access the connector without needing to fully disassemble the housing. If you're still struggling to reach it, double-check that you've removed all the housing fasteners for your specific model before forcing anything. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the 6V rating, series wiring, and housing fit of the original W11130208 / W11683241 LED light module used in compatible Whirlpool, KitchenAid, and Kenmore Elite refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

(6 Pack) EXPHV13 Microwave High Voltage Diode (Rectifier)  Replaces Part Numbers: W11256462, W10492278, W10886077, WPW10492276, WPW10575765, AP6784287, PS12584264, WPW10687786, W10687786, 4449228, AP6023790, PS11757136, 5304470521, AP4396425, PS2353199, WB27X10597, AH239740, EA239740, AP3192533, PS239740. CL04-12A=500mA CL04-12 12kV Description: This Diode Assembly is a replacement part for specific microwave models. It plays a crucial role in converting alternating current (AC) to direct current (DC), which is essential for the microwave’s high-voltage functions, including powering the magnetron to generate microwave energy. Over time, diodes can fail due to electrical surges, excessive heat, or wear and tear. A faulty diode assembly can lead to inefficient or non-functional microwave operation, impacting its ability to heat food properly. EXPHV13 Microwave High Voltage Diode – OEM-Quality Replacement Replace your faulty diode with the EXPHV13, a high-quality, aftermarket microwave high voltage diode rated for 12,000V / 500mA. It restores proper heating function and is compatible with many leading microwave brands. Key Features: ✅ Rated for 12kV, 500mA ✅ Direct replacement for most standard microwaves ✅ Solves issues like no heat, humming, or tripped breakers ✅ Easy-to-install universal fit for GE, LG, Whirlpool, Panasonic, etc. ⚠️ Always disconnect power before installation. For compatibility questions, contact us—we’re happy to help! 📦 Part Number: EXPHV13💯 30-Day Money Back Guarantee

Read more less

XPMTC-180 Microwave Thermal Cut-Off Fuse 180℃ (356°F) – Normally Closed – Universal Microwave Safety Cutoff Product Description Protect your microwave from extreme overheating with the XPMTC-180 Microwave Thermal Cut-Off Fuse 180℃ (356°F), Normally Closed. This high-temperature safety device is designed to remain closed (conductive) during normal operation and open permanently when internal temperatures exceed 180℃, immediately cutting power to prevent serious damage or fire risk. A tripped thermal cut-off can cause the microwave to lose power or stop heating. Replacing it with the correctly rated NC fuse restores safe and reliable operation. Replaces Part Numbers XPMTC-180, MTC-180, Microwave Thermal Fuse 180C NC, 356F Normally Closed Thermal Cutoff, WB24X29270, 4586233, PD00045446, EAP12170419, KSD1 BR1 180, AP6262395, PS12170419, 6930W1A003X, 1365203, AH3530468, EA3530468, PD00001857, AP4443816, PS3530468. Compatibility This normally closed microwave thermal cut-off fuse is compatible with many GE, Whirlpool, Samsung, LG, Frigidaire, Panasonic, Sharp, and Kenmore microwave ovens that require a 180℃ (356°F) NC thermal cutoff. Commonly used near the magnetron, high-heat zones, or cavity protection points. Always verify temperature rating and contact type before ordering.Contact our support team if you’re unsure. 🔍 What’s the Difference Between NC and NO Thermal Cut-Offs? Normally Closed (NC): Circuit is closed during normal operation and opens permanently when the rated temperature is reached.👉 Most microwave thermal cut-offs are NC. Normally Open (NO): Circuit is open during normal operation and closes only when overheated (used in limited designs). ⚠️ Installing the wrong type (NC vs NO) may cause the microwave not to run or fail to protect against overheating. ✅ Key Features 🔄 Aftermarket Replacement – Built to OEM-equivalent safety specifications 🌡️ 180℃ (356°F) Rating – Designed for high-temperature protection zones 🔁 Normally Closed (NC) – Conducts power during normal operation 🛡️ Critical Safety Component – Prevents overheating and fire hazards 💰 Cost-Effective Repair – Affordable alternative to OEM thermal cut-offs 📐 Product Specification Part Number: XPMTC-180 Component Type: Microwave Thermal Cut-Off Fuse Temperature Rating: 180℃ (356°F) Contact Type: Normally Closed (NC) Function: One-time safety cutoff Material: Heat-resistant metal body Application: Magnetron or high-heat cavity temperature protection Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, insulated pliers ⚠️ Safety First:Unplug the microwave before servicing. Microwaves contain high-voltage components—allow capacitors to discharge before handling internal parts. Basic Steps: Disconnect microwave power. Remove the outer cabinet or access panel. Locate the thermal cut-off near the magnetron or high-heat area. Disconnect wiring and remove the failed fuse. Install the new XPMTC-180 (NC) thermal cut-off in the same position. Reassemble the microwave and restore power. Test operation. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore microwave safety under extreme heat conditions — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

(5 Pack) XP5KV07A Microwave High Voltage Fuse 0.7A (700mA), 5kV – Compatible with GE, LG, Whirlpool, Samsung, and Panasonic Microwaves Product Description Protect your microwave’s high-voltage system with the XP5KV07A Microwave High Voltage Fuse (0.7A, 5kV). This high-quality aftermarket replacement safeguards essential high-voltage components—including the magnetron, diode, and capacitor—from power surges and electrical overloads. If your microwave is completely dead or stops heating, a blown HV fuse is a common cause. Replacing it with this XPARTCO fuse restores safe, reliable operation. Replaces Part Numbers 5KV0.7A, 700mA 5kV Fuse, HVF-07A, AP-HV07A, and equivalent high-voltage 0.7A microwave fuses Compatibility This replacement high-voltage fuse fits many GE, LG, Samsung, Whirlpool, Panasonic, Sharp, Kenmore, Maytag, and other leading microwave brands. Common compatible models include (but are not limited to):GE JVM3160RFSS, LG LMV2031ST, Samsung ME19R7041FG, Whirlpool WMH31017HS, Panasonic NN-SN686S. Always verify your microwave’s fuse specs before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM electrical ratings and safety performance ⚡ High-Voltage Protection – Rated 0.7A (700mA) at 5,000 volts for microwave HV systems 💰 Budget-Friendly Fix – Reliable option for restoring microwave operation 🛠️ Easy Installation – Direct-fit size compatible with standard HV fuse holders 🛡️ Fixes Common Issues – Solves “microwave dead,” no heat, or fuse-blown conditions 📐 Product Specification Part Number: XP5KV07A Component Type: Microwave High Voltage Fuse Amperage: 0.7A (700mA) Voltage Rating: 5 kV Material: Ceramic-body fuse with metal end caps Dimensions: Standard HV fuse size (approx. 6×40 mm) Compliance: Meets high-voltage protection standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, needle-nose pliers ⚠️ Safety First: Microwave repairs involve high voltage even when unplugged. Only qualified persons should replace HV fuses. Steps (for trained technicians): Unplug the microwave and safely discharge the HV capacitor. Remove outer cabinet screws and lift the cover. Locate the high-voltage fuse near the HV transformer and capacitor. Remove the blown fuse and install the new XP5KV07A fuse. Reassemble the unit and test heating operation. ⏱️ Time Required: 10–20 minutes (professional preferred) 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore microwave safety and power protection — Add to Cart Now for a reliable, affordable replacement!

Read more less

XPARTCO 5304517886 Refrigerator / Freezer LED Light Bulb – Compatible with Frigidaire, Electrolux, and Kenmore Refrigerators Product Description Restore bright, energy-efficient interior lighting with the XPARTCO 5304517886 Refrigerator / Freezer LED Light Bulb. This high-quality aftermarket replacement provides clear, long-lasting illumination inside the refrigerator and freezer compartments. A failed LED bulb can cause dim or no lighting, making it difficult to see stored food. Replacing it with this XPARTCO LED bulb ensures reliable brightness while consuming less energy than traditional bulbs. Replaces Part Numbers 5304517886, 216846400, 216518101, 5304510893, 240588001, 241552807, 297114000, 5304498578, 5304509249, 5304520040, 216222700, 216518100, 216608600, 216988000, 216988100, 241552801, 3091423, 4929381, 5303091423, 5304495326, 7216988100, 7241552801, 7297114000, C000501867, F000092472, KEI D28M, KEID28M, KEL 2815, KEL2815, AC100-265V 3.8W, PD00051346, EAP12712277, AP6873911, PS12712277. Compatibility This replacement LED light bulb fits select Frigidaire, Electrolux, and Kenmore refrigerators. Example compatible models include (but are not limited to):Frigidaire FFSS2615TS0, FGHC2331PF5Electrolux EI23CS55GS1Kenmore 253.7031321A Always verify your refrigerator’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM brightness and fit 💡 Bright LED Illumination – Daylight 5000k, Clearly lights refrigerator and freezer interiors ⚡ Energy Efficient – Low power consumption with long service life 🛠️ Plug-and-Play Installation – Direct-fit bulb installs in minutes 🛡️ Fixes Common Issues – Solves dim lighting, flickering, or no interior light 📐 Product Specification Part Number: 5304517886 Component Type: Refrigerator / Freezer LED Light Bulb Light Type: LED Color Temperature: Cool white, Daylight 5000k Mounting: Twist-in or clip-in base (model dependent) Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: None (gloves recommended) ⚠️ Safety First: Unplug the refrigerator or turn off power before replacing the light bulb. Steps: Disconnect power to the refrigerator. Remove the light cover, if applicable. Remove the old LED bulb. Install the new XPARTCO 5304517886 LED bulb securely. Reinstall the cover and restore power. Confirm proper illumination. ⏱️ Time Required: 5 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Brighten your refrigerator interior again — Add to Cart Now for a simple, cost-effective lighting upgrade!

Read more less

XP5KV07A Microwave High Voltage Fuse 0.7A (700mA), 5kV – Compatible with GE, LG, Whirlpool, Samsung, and Panasonic Microwaves Product Description Protect your microwave’s high-voltage system with the XP5KV07A Microwave High Voltage Fuse (0.7A, 5kV). This high-quality aftermarket replacement safeguards essential high-voltage components—including the magnetron, diode, and capacitor—from power surges and electrical overloads. If your microwave is completely dead or stops heating, a blown HV fuse is a common cause. Replacing it with this XPARTCO fuse restores safe, reliable operation. Replaces Part Numbers 5KV0.7A, 700mA 5kV Fuse, HVF-07A, AP-HV07A, and equivalent high-voltage 0.7A microwave fuses Compatibility This replacement high-voltage fuse fits many GE, LG, Samsung, Whirlpool, Panasonic, Sharp, Kenmore, Maytag, and other leading microwave brands. Common compatible models include (but are not limited to):GE JVM3160RFSS, LG LMV2031ST, Samsung ME19R7041FG, Whirlpool WMH31017HS, Panasonic NN-SN686S. Always verify your microwave’s fuse specs before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM electrical ratings and safety performance ⚡ High-Voltage Protection – Rated 0.7A (700mA) at 5,000 volts for microwave HV systems 💰 Budget-Friendly Fix – Reliable option for restoring microwave operation 🛠️ Easy Installation – Direct-fit size compatible with standard HV fuse holders 🛡️ Fixes Common Issues – Solves “microwave dead,” no heat, or fuse-blown conditions 📐 Product Specification Part Number: XP5KV07A Component Type: Microwave High Voltage Fuse Amperage: 0.7A (700mA) Voltage Rating: 5 kV Material: Ceramic-body fuse with metal end caps Dimensions: Standard HV fuse size (approx. 6×40 mm) Compliance: Meets high-voltage protection standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, needle-nose pliers ⚠️ Safety First: Microwave repairs involve high voltage even when unplugged. Only qualified persons should replace HV fuses. Steps (for trained technicians): Unplug the microwave and safely discharge the HV capacitor. Remove outer cabinet screws and lift the cover. Locate the high-voltage fuse near the HV transformer and capacitor. Remove the blown fuse and install the new XP5KV07A fuse. Reassemble the unit and test heating operation. ⏱️ Time Required: 10–20 minutes (professional preferred) 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore microwave safety and power protection — Add to Cart Now for a reliable, affordable replacement!

Read more less