Search results for "Tub Seals"

WH13X26535 Genuine OEM GE Washer Water Valve The WH13X26535 is a genuine GE OEM water inlet valve assembly for GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café models. This valve controls the flow of hot and cold water into the tub during the fill portion of the cycle, ensuring each wash uses the correct amount of water at the right temperature blend. It's housed in durable gray plastic. Common failure causes include mineral or sediment buildup inside the valve body, a burned-out internal solenoid coil, and general wear over years of use — five years is a commonly cited service life before this valve starts to show problems. A failing valve produces a clear set of symptoms: the washer not filling properly, water continuing to fill or drip even when the washer is turned off, or leaking near the valve area. It directly replaces AP6892695, WH13X24386, 4931303, PS12726769, WH13X24392, WH13X26535-25PK, EAP12726769, and PD00052736. As a genuine OEM part, the WH13X26535 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance. Quick Answer The WH13X26535 Genuine OEM GE Washer Water Valve fixes GE top-load washers that aren't filling properly, are overfilling, or have water slowly dripping into the tub even when the washer is off. Housed in gray plastic. Replaces AP6892695, WH13X24386, 4931303, PS12726769, WH13X24392, WH13X26535-25PK, EAP12726769, PD00052736. This replacement valve does not include a thermistor or gasket — if your old valve has a thermistor mounted in front of the solenoids, you'll need to transfer it (with its gasket) to the new valve. Also not the same as the similarly-numbered WH13X26534, which is a separate valve for other GE/Hotpoint models. Common Problems This Part Fixes Washer not filling with water properly Washer overfilling Water slowly dripping or leaking into the tub even when the washer is turned off Leaking near the valve connections No hot water reaching the tub, or no cold water reaching the tub Cycle stalling at the fill step and never advancing to wash Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: WH13X26535, WH13X24386, WH13X24392, 4931303, 003C17, AGE26261, AP6892695, 4476388, 4931303, OEM20678094, EAP11729481, EAP12726769, K-78637-2, PD00052736, PS12726769. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café washers built on the GE platform, spanning model series GTW460, GTW465, GTW485, GTW490, GTW500, GTW525, GTW540, and VTW540, including specific model numbers such as 5TW4207ST0WS, 5TW4307SW0WS, ETW485ASW0WB, GTW460AMJ0WW, GTW460AMJ1WW, and GTW460AMJ2WW. Note — thermistor transfer required, and not the same as WH13X26534: This valve does not include a thermistor or the rubber gasket that seats it. If your original valve has a thermistor mounted in front of the solenoids, you must transfer that thermistor and its gasket onto this new valve during installation. Separately, this part is not the same as the similarly-numbered WH13X26534, a distinct valve used on other GE/Hotpoint models with its own cross-reference set (PS12726768, AP6891106). Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified solenoid design and housing Controls hot and cold water flow into the tub Resolves "won't fill properly," "overfilling," and "dripping into the tub when off" symptoms caused by valve failure Durable gray plastic housing Direct drop-in replacement — matches the original mounting and hose connections Replaces AP6892695, WH13X24386, 4931303, PS12726769, WH13X24392, WH13X26535-25PK, EAP12726769, and PD00052736 Compatible with GE, Hotpoint, Haier, Monogram, and Café top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Moderate DIY repair, typically 30 to 60 minutes Product Specifications Part Number WH13X26535 Part Type Washer Water Inlet Valve Condition Genuine OEM Application Top-Load Washers Housing Material Gray plastic Includes Thermistor/Gasket No — transfer from old valve if equipped Repair Difficulty Moderate — 30 to 60 minutes Quantity 1 valve Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Watch For The Thermistor O-Ring Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Access is typically behind the front control panel or top of the cabinet, depending on your model. The valve assembly is usually held in place with a metal plate and two screws. Photograph the wiring and hose connections before disconnecting anything. If your old valve has a thermistor (temperature sensor) mounted in front of the solenoids, it fits into a small hole in the bracket and uses an O-ring seal that's known to degrade and leak over time — this new valve does not include one, so you'll need to carefully transfer the thermistor and its gasket from the old valve to the new one. Disconnect the electrical connector and outlet hoses from the old valve, remove its mounting screws, and pull it free. Transfer the thermistor and gasket to the new WH13X26535 if applicable, then install it in the same position, reconnect all outlet hoses to their original positions, reconnect the electrical connector, and secure the mounting screws. Reattach the hot and cold supply hoses, tightening securely. Restore the water supply and check every connection for leaks before restoring power. Run a full test cycle across a few different temperature settings to confirm each fill function works correctly with no leaking. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions Does this valve come with the thermistor? No. This valve no longer comes with the rubber gasket or thermistor that some GE washers use, mounted directly in front of the solenoids. If your old unit has one, you'll need to remove it from the old valve, along with its gasket, and transfer it onto this new valve during installation. Water has been slowly leaking into my tub even when the washer is off. Is that this valve? Yes, this is a documented cause. One customer traced over a year of slow leaking directly to this valve's thermistor O-ring, which is known to degrade over time and let water seep through even when the washer isn't running. Replacing the valve (and transferring a good thermistor and gasket if your model uses one) resolves this type of slow leak. Is this the same as WH13X26534? No, these are two separate GE valve part numbers with different cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close number match. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, housing, and connection type of the water inlet valve originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11688994 Washer Genuine OEM Water Valve Single water inlet valve, hot Replaces Part Numbers: W11688994, W11316255, W11036928, W11486360, AP7218602, PS17216729. Description: This Water Inlet Valve is a Genuine OEM part for specific Maytag, Kenmore, Whirlpool washing machine models. It controls the flow of water into the washer tub at designated stages in the washing process. Water enters through the valve inlet and is distributed to internal components like the detergent dispenser, water pipes, and sump hoses. Common causes of a bad valve can include mineral scale buildup inhibiting proper flow regulation over time, or cracks and leaks from wear and tear on rubber gaskets and seals. 

Read more less

W11168740 - W11168743 Washer Water Valve Set for W11127357 Cold and Hot Washer Water Inlet Valve Housing and Wire Harness not included. Fits Kenmore, Maytag, Whirlpool top load washer models. Replaces Part Number:W11168740, WPW10240949, W10240949, W10921514, AP6285450, PS12348073, W11127357, W11127357, W10678672, W10678676, W10849466, W10921581, W11085642, AP6261887, PS12347475, W11168743, WPW10240948, W10240948, W10921515, AP6327638, PS12348074. Description: This Water Inlet Valve set is a replacement part for specific Kenmore, Maytag, Whirlpool washing machine models. It controls the flow of water into the washer tub at designated stages in the washing process. Water enters through the valve inlet and is distributed to internal components like the detergent dispenser, water pipes, and sump hoses. Common causes of a bad valve can include mineral scale buildup inhibiting proper flow regulation over time, or cracks and leaks from wear and tear on rubber gaskets and seals.    This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

EXPW79SC (8 Pack) Washing Machine Fill Hose Gasket with Screen 8 Pack compatible with 5/ 8 inch washing machine and 3/4 inch garden hose Fine Screen the rubber washer with stainless steel filter mesh, serves as a flow restrictor can reduce the waste of water effectively     

Read more less

XPARTCO 5221ER1003S Washer Water Valve The XPARTCO 5221ER1003S is an aftermarket replacement cold water inlet valve for LG and select Kenmore front-load washers. This valve sits underneath the top panel, at the point where the cold water supply hose connects, and it's the gatekeeper for cold water entering the tub. When the control calls for a cold fill, it energizes the valve's solenoid to open, admitting water; once the correct level is reached, it closes again. This part controls the cold water side specifically — hot fills on these washers are governed by a separate valve. Rated 12V and terminated with small male spade connectors, this valve measures approximately 4.75"H x 3.25"W x 2.25"L, with a gray plastic and metal housing. Over time, rust and mineral buildup inside the valve body — a documented failure point on this platform — can prevent it from sealing fully, which lets water continue flowing even after the valve is told to close. A washer that keeps filling even while draining, or that leaks steadily at the cold connection, is a strong sign of exactly this kind of stuck-open valve failure. Other failure modes include a burned-out solenoid coil and general wear from age. It directly replaces 4869496, AP6798394, PS12587936, and EAP12587936, and is also cross-referenced to the related 5221ER1003A part number. Quick Answer The XPARTCO 5221ER1003S Washer Water Valve fixes LG and select Kenmore front-load washers where cold water won't fill, fills slowly, keeps filling continuously (even while draining), or leaks at the water connection. 12V cold water inlet valve, small male spade terminals, 4.75"H x 3.25"W x 2.25"L. Replaces 4869496, AP6798394, PS12587936, EAP12587936. Rust and mineral buildup inside the valve body is a documented cause of it sticking open — check for rust at the connection before you order. Common Problems This Part Fixes Washer won't fill with cold water at the start of the cycle Cold water fills much more slowly than it used to Washer keeps filling continuously, even while water is simultaneously draining out Water leaking steadily at the cold water connection point Visible rust or mineral buildup around the valve body or connection Cycle stalling at the fill step and never advancing to wash Water pooling underneath or behind the washer near the cold supply line Cold wash or cold rinse cycles specifically affected while other cycles run fine Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer cold water inlet valve directly replaces the following OEM and cross-reference part numbers: 5221ER1003S, 5221ER1003A, 4869496, AP6798394, PS12587936, ALG51905, PD00057211, EAP12587936 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cold water inlet valve is compatible with select LG front-load washers, and also fits select Kenmore front-load washers built on the LG platform, including model numbers such as: LG WM4000HBA, WM4000HWA, WM3400CW, WM3470CW LG W3600HVA Kenmore WKE100HVA (select LG-built models) Note — cold side only: This is the cold water valve. Some LG front-load washers use a separate hot water valve for the hot supply connection — if hot water fills normally but cold does not, this valve is the correct part; if the issue affects both hot and cold fills, the problem may lie elsewhere in the fill circuit. This valve is specific to LG's front-load platform and is not intended for top-load washers. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement cold water inlet valve for LG and select Kenmore front-load washers Resolves "won't fill with cold water," "fills slowly," "keeps filling continuously," and "leaking at the connection" symptoms caused by valve failure Rated 12V with small male spade terminal connections for a secure electrical fit Gray plastic and metal housing, approximately 4.75"H x 3.25"W x 2.25"L Direct drop-in replacement — mounts underneath the top panel at the original connection point Replaces 4869496, AP6798394, PS12587936, and EAP12587936 Compatible with LG and select Kenmore front-load washers Aftermarket replacement built to OEM-equivalent quality standards Straightforward DIY repair using basic hand tools Product Specifications Part Number 5221ER1003S OEM Part Number 5221ER1003S (also 5221ER1003A) Part Type Washer Water Inlet Valve — Cold Condition Aftermarket Replacement Brand LG Application Front-Load Washers Voltage 12V Electrical Connection Small male spade terminals Color Gray Material Plastic and metal Height 4.75 in. Width 3.25 in. Length 2.25 in. Location Underneath the top panel, dispenser and control panel assembly Quantity 1 valve Compatible Brands LG, select Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Have A Towel Ready Unplug the washer and shut off the cold water supply valve before beginning. Wear work gloves. Pull the washer away from the wall for access. Unthread the cold water supply line from the back of the valve first — have a towel ready, since residual water will spill out. Unthread the two screws securing the top panel, then slide the panel back and lift it off to access the valve assembly underneath. Photograph the wiring connections before disconnecting anything. Disconnect the spade terminal wire connectors from the old valve, remove its mounting screw or bracket, and pull the valve free. While it's out, inspect the area for rust or mineral scale, and clean the connection point if needed before installing the new valve. Install the new 5221ER1003S in the same position, reconnect the spade terminals, and secure the mounting hardware. Rethread the cold water supply line onto the new valve, tightening securely. Reinstall the top panel and its two screws. Restore the water supply and power, then run a short cycle and confirm the tub fills at the normal rate with no leaking underneath or behind the washer. Tools needed: channellock pliers, flathead screwdriver, pliers, drill/driver with a Phillips bit, towel, work gloves. Frequently Asked Questions My washer keeps filling even while it's draining. Is that this valve? Yes, this is a well-documented failure mode on this platform. Rust and mineral buildup inside the valve body can prevent it from sealing fully closed, so water keeps trickling or flowing into the tub even after the fill portion of the cycle has ended — sometimes enough to keep pace with draining, making it look like the washer is filling and draining simultaneously. If you open up the top panel and see rust around the valve, that strongly confirms this diagnosis. Cold water won't fill but hot water works fine. Is this the right part? Yes — this valve controls cold water specifically, and some LG front-load washers use a separate valve for the hot supply. If cold-specific cycles are failing while hot water fills normally, this cold valve is the correct part to replace. I see rust on my old valve but it isn't leaking yet. Should I still replace it? It's worth strongly considering. Rust and mineral buildup on this valve is a known precursor to it sticking partially open, which can lead to continuous filling, water waste, and potential water damage if it isn't caught. If you're already inspecting the area and see corrosion forming, replacing the valve proactively is often cheaper and easier than dealing with an active leak later. What's the difference between 5221ER1003S and 5221ER1003A? These are cross-referenced as the same valve — 5221ER1003A appears on some parts diagrams and listings as an alternate or prior designation for the identical part. If your washer's diagram shows either number, this listing is the correct replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the 12V solenoid design, spade terminal connections, and dimensions of the original 5221ER1003S cold water valve used in compatible LG and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH13X10031 Washer Water Inlet Valve The XPARTCO WH13X10031 is an aftermarket replacement water inlet valve for GE washer/dryer combo units, and also fits select Hotpoint and Kenmore combo models. This valve controls the flow of water into the washer side of the combination unit, opening to admit hot and cold water as the cycle calls for it and closing once the correct fill level is reached. Made of durable metal construction for long-term reliability. Rated 115V. Common failure causes include mineral or sediment buildup inside the valve body and general electrical wear in the solenoid coils. A failing valve produces a clear set of symptoms: the washer side not filling properly, water continuing to enter the machine even when it's turned off, or leaking near the valve connections. Quick Answer The XPARTCO WH13X10031 Washer Water Inlet Valve fixes GE washer/dryer combo units (and select Hotpoint and Kenmore combo models) that aren't filling properly, or where water continues entering the machine even when it's turned off. 115V, metal construction. This is a combo washer/dryer unit valve — a different application from a standalone top-load or front-load washer valve. Confirm your unit type before ordering. Common Problems This Part Fixes Washer side of the combo unit not filling with water properly Water continuing to enter the machine even when it's turned off Leaking near the valve connections Cycle stalling at the fill step and never advancing to wash No hot water reaching the tub, or no cold water reaching the tub Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers WH13X10031, 1264513, AGE1189086, AP3995207, PS1482394. We were not able to confirm additional cross-reference or superseding part numbers for this specific part from reliable sources at the time this page was built, so none are listed here rather than guessed. If you have a cross-reference number for your appliance, contact our support team and we will verify compatibility before you order. Compatibility This water inlet valve is compatible with select GE washer/dryer combo units, and also fits select Hotpoint and Kenmore combo models built on the GE platform. Note — combo unit valve, not a standalone washer valve: This valve is specifically designed for washer/dryer combo units. GE also sells several similarly-numbered valves for standalone top-load and front-load washers, including WH13X10015, WH13X10030, WH13X10033, and WH13X10037 — these are separate parts for different platforms and are not interchangeable with this combo unit valve. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which valve your appliance needs. Key Features Aftermarket replacement water inlet valve for GE washer/dryer combo units Resolves "won't fill properly" and "water continues entering when off" symptoms caused by valve failure Rated 115V Durable metal construction Direct drop-in replacement — matches the original mounting and hose connections Compatible with GE, Hotpoint, and Kenmore washer/dryer combo units Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number WH13X10031 OEM Part Number WH13X10031 Part Type Washer/Dryer Combo Water Inlet Valve Condition Aftermarket Replacement Application Washer/Dryer Combo Units Voltage 115V Material Metal Quantity 1 valve Compatible Brands GE, Hotpoint, Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug The Unit Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Access to the valve on combo units typically requires removing a front or rear access panel — check your model's service diagram, since access varies more on combo units than on standalone washers. Photograph the wiring and hose connections before disconnecting anything. Disconnect the water supply lines from the old valve, disconnect the electrical connector, and remove the mounting screws holding it in place, then pull the valve free. Install the new WH13X10031 in the same position, reconnect all hose connections to their original positions, reconnect the electrical connector fully, and secure the mounting screws. Reattach the hot and cold supply lines, tightening securely. Restore the water supply and check every connection for leaks before restoring power. Run a full test cycle to confirm the washer side fills correctly with no leaking. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions Is this the right valve for my standalone washer, or only for a combo unit? This valve is designed specifically for GE washer/dryer combo units, where the washer and dryer are built into a single appliance. If you have a standalone washer, this is not the correct valve — GE uses several other similarly-numbered valves, such as WH13X10015, WH13X10030, WH13X10033, and WH13X10037, for standalone top-load and front-load washers. Confirm your unit type and model number before ordering. Water keeps entering my machine even when it's off. Is this the valve? Yes, this is a documented symptom of a failing water inlet valve. If the internal solenoid is stuck open or has worn out, water can continue to flow into the machine even after it's been turned off, since the valve can no longer fully seal. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the voltage rating, solenoid design, and connection type of the original WH13X10031 valve used in compatible GE, Hotpoint, and Kenmore washer/dryer combo units. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

EXPW79SC (4 Pack) Washing Machine Fill Hose Gasket with Screen 4 Pack compatible with 5/ 8 inch washing machine and 3/4 inch garden hose Fine Screen the rubber washer with stainless steel filter mesh, serves as a flow restrictor can reduce the waste of water effectively     

Read more less

Genuine Refrigerator Replacement Part WPW10276792 Refrigerator Genuine Water Reservoir Tubing Genuine water reservoir tubing for select refrigerator water-dispensing systems. Product Overview The WPW10276792 Refrigerator Water Reservoir Tubing is a genuine replacement part designed for compatible refrigerators. The tubing routes and stores chilled water within the refrigerator water system before water is delivered to the dispenser. Use this part when the original tubing is leaking, cracked, kinked, damaged, or otherwise unable to maintain proper water flow. Quick Answer WPW10276792 is genuine refrigerator water reservoir tubing for compatible models. Replace it when the original tubing is leaking, split, damaged, or restricting normal dispenser water flow. Common Problems This Part May Fix Water leaking inside the refrigerator Cracked or split reservoir tubing Kinked tubing restricting water flow Reduced or inconsistent dispenser water flow Damaged tubing connections or fittings Replaces and Cross-References WPW10276792, 1874366, 2223876, 2305226, 2307107, W10204356, W10276792, W10526445, WP2305226, AP6018425, AWP50256, EAP2580224, PD00028740, PS2580224 Part number is provided for identification. This listing is for a genuine replacement part. Compatibility Fits select refrigerators that specify water reservoir tubing part number WPW10276792. Important: Verify the complete refrigerator model number and original tubing part number before ordering. Refrigerator water tubing can differ in length, routing, connector style, and reservoir design. Key Features Genuine replacement part Designed for compatible refrigerator water systems Routes and stores chilled dispenser water Helps restore proper water flow and leak-free operation Direct replacement for applications calling for WPW10276792 Product Specifications Part Number WPW10276792 Part Type Refrigerator Water Reservoir Tubing Application Compatible Refrigerators Function Water storage and routing for dispenser system Condition New Part Quality Genuine Replacement Part Package Quantity 1 Tubing Assembly Installation & Troubleshooting Notes Disconnect refrigerator power and shut off the household water supply before service. Relieve water pressure from the dispenser system before disconnecting tubing. Inspect the original tubing for leaks, splits, kinks, or damaged fittings. Route the replacement tubing in the same path and orientation as the original. Confirm all connections are fully seated and secure. Restore the water supply and carefully check for leaks before returning the refrigerator to normal use. Diagnostic tip: A dispenser leak may also come from a valve, connector, fitting, or dispenser line. Confirm the source of the leak before replacing the reservoir tubing. Frequently Asked Questions What does WPW10276792 do? It routes and stores water within the refrigerator water system before the water is delivered to the dispenser. Is WPW10276792 a genuine part? Yes. This listing is for a genuine replacement water reservoir tubing assembly. When should this tubing be replaced? Replace it if it is leaking, cracked, split, kinked, damaged, or restricting normal water flow. Will this fit every refrigerator? No. Match the complete refrigerator model number and original part number before ordering. Shop With Confidence Verify your complete refrigerator model number before purchasing. Our compatibility team can help confirm whether WPW10276792 is correct for your appliance. Genuine ReplacementWater Reservoir TubingModel Fitment SupportFast U.S. Shipping

Read more less

WH23X28418 Washer Genuine GE OEM Drain Pump The WH23X28418 is a Genuine GE OEM replacement drain pump and motor assembly compatible with select GE, Hotpoint, Haier, RCA, and Kenmore top-load and front-load washers. The drain pump removes water from the washer drum during the drain and spin cycles — expelling water and detergent through the drain hose so that clothing comes out clean and free of excess water. When the pump fails, the washer will not drain, may leave standing water in the tub, or may produce loud noises during the drain cycle. This complete drain pump and motor assembly is rated at 120V, 60Hz, 1.25A with a duty cycle of 10 minutes on and 50 minutes off. It includes the pump and motor with harness — the harness and plug extend approximately 10 inches from the motor. The pump measures 5-1/4" L x 5-1/8" W x 5-1/2" H and includes a drain pump seal. It directly replaces WH23X24178 and WH23X27574, as well as several additional cross-reference numbers. Installs in 20–40 minutes with basic hand tools. Quick Answer The WH23X28418 Washer Genuine GE OEM Drain Pump fixes GE, Hotpoint, Haier, and RCA washers that won't drain, leave standing water in the tub, are noisy during draining, or leak around the pump area. Complete pump and motor with harness and drain pump seal. 120V/60Hz/1.25A. Dimensions 5-1/4" L x 5-1/8" W x 5-1/2" H; harness extends approx. 10". Replaces WH23X24178 and WH23X27574. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Washer stopping mid-cycle due to a drain fault or drain-related error code Loud humming, grinding, or buzzing noise during the drain cycle Washer pumps but will not spin — pump failure preventing cycle completion Water leaking from around the drain pump area Clothes not clean or coming out soaking wet due to incomplete drainage Pump impeller jammed by debris causing motor burnout Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: WH23X24178, WH23X28418, WH23X27574, 290D1201G001, 290D1201G002, 290D1201G003, AGE26155, B40-3A01, B30-3A02, PD00055680, EAP12723115, AP6889136, PS12723115. WH23X28418 is the current updated part number replacing the discontinued WH23X24178 and WH23X27574. If your washer documentation or old pump label shows either of those numbers, this is the correct replacement. Compatibility This drain pump is compatible with select washers from the following brands and series: GE top-load washers — GTW220, GTW330, GTW335, GTW460, GTW465, GTW485, GTW490, GTW500, GTW680, GTW720, GTW725, GTW750 series and others GE front-load washers — select GFW series models Hotpoint top-load washers — HTW200, HTW240 series and others Haier top-load washers — select models RCA top-load washers — select models Kenmore / Sears washers — select GE-built models Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Removes water and detergent from the washer drum during drain and spin cycles Complete assembly — includes pump motor, harness, and drain pump seal Rated 120V, 60Hz, 1.25A with a 10-minute on / 50-minute off duty cycle Dimensions: 5-1/4" L x 5-1/8" W x 5-1/2" H; harness and plug extend approximately 10" from motor Plastic and metal construction rated CL.A — durable and chemical resistant Includes drain pump seal to prevent leaks at the pump connection Current updated replacement for discontinued WH23X24178 and WH23X27574 — direct fit Note: The drain pump motor has been redesigned by the manufacturer — the replacement may look different from the original but fits and functions identically Genuine GE OEM part — factory-exact fit, materials, and specifications DIY-friendly repair — installs in 20–40 minutes with basic hand tools Product Specifications Part Number WH23X28418 Supersedes WH23X24178, WH23X27574 (both discontinued) Part Type Washer Drain Pump and Motor Assembly Condition Genuine OEM Application GE, Hotpoint, Haier, RCA Top-Load and Front-Load Washers Voltage 120V AC Frequency 60 Hz Amperage 1.25A Rating CL.A Duty Cycle 10 minutes ON / 50 minutes OFF Dimensions 5-1/4" L x 5-1/8" W x 5-1/2" H Harness Length Approximately 10 inches from motor Color White / Black / Gray Material Plastic / Metal Includes Pump and motor with harness, drain pump seal Compatible Brands GE, Hotpoint, Haier, RCA, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Have towels and a shallow pan ready to catch residual water. For top-load GE washers, the drain pump is typically accessed from the bottom of the machine — carefully tilt the washer back onto a support or lay it on its side to reach the pump from underneath. Disconnect the outlet hose by loosening the hose clamp and pulling it free. Disconnect the electrical harness connector. Remove the mounting screws (typically three) securing the pump to the washer base. Twist and firmly pull the old pump out. Install the new WH23X28418 pump in reverse order — connect the hose, tighten the clamp, reconnect the harness, and secure the mounting screws. Restore power and water supply and run a test cycle to verify proper drainage and no leaks. Tools needed: Phillips screwdriver, flat-head screwdriver, slip-joint pliers, shallow pan. Frequently Asked Questions What is the relationship between WH23X28418, WH23X24178, and WH23X27574? All three are GE washer drain pumps — WH23X28418 is the current updated part number that replaced both the discontinued WH23X24178 and WH23X27574. GE redesigned the pump motor during its production cycle, so the replacement may look slightly different from the original, but it fits and functions identically. If your washer uses either of the older numbers, order WH23X28418. How do I know if my washer drain pump has failed? The most common signs are standing water in the tub after a cycle, the washer stopping mid-cycle with a drain error, or loud humming during the drain phase — which indicates the motor is running but the impeller is not moving. A grinding or rattling noise suggests debris in the pump or physical damage. If the pump is completely silent during what should be the drain cycle, the motor has likely burned out and the pump needs replacement. Does the WH23X28418 fit both top-load and front-load GE washers? The WH23X28418 is primarily used in GE and Hotpoint top-load washers — the GTW and HTW series make up the majority of compatible models. It also fits select GE front-load models. Always verify your specific model number before ordering to confirm compatibility for your washer type. What is the duty cycle rating and why does it matter? The duty cycle of 10 minutes on / 50 minutes off means the pump motor is rated for up to 10 consecutive minutes of operation before requiring a 50-minute rest period. In normal washer operation this is never an issue — drain cycles are brief. However, if a drain fault causes the pump to run continuously without successfully draining, the motor can overheat. If you replace the pump due to burnout and the new pump also fails quickly, check for a drain hose blockage or control board fault that may be causing the pump to run without limit. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications — the exact same drain pump and motor assembly installed in compatible models from the factory, with guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO W11688995 Washer Water Inlet Valve (Cold) The XPARTCO W11688995 is an aftermarket replacement cold water inlet valve designed as a direct fit for select Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers. The cold water inlet valve is mounted at the back of the washer where the cold water supply hose connects. When the washer's control board calls for cold water during a wash cycle, the valve's internal solenoid opens, letting water flow into the tub or detergent dispenser. The valve closes the instant the control board cuts power, stopping flow precisely as the correct fill level is reached. When this valve fails, the washer may not fill with cold water at all, fill very slowly, fail to dispense fabric softener, continuously drip water into the tub even when off, or display F8E1 or LO FL error codes. Construction is blue and white plastic with metal solenoid coil, ~3"H x 4"W x 3"L, with 1/2" NPT threaded inlet for standard washer supply hose. It directly replaces W11688995, W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737. Often replaced as a pair with the hot water inlet valve (W11688994, sold separately). Installs in 10–15 minutes with basic hand tools. Quick Answer The XPARTCO W11688995 Washer Water Inlet Valve (Cold) fixes Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, and Kenmore front-load washers displaying F8E1 or LO FL error codes, not filling with cold water, filling slowly, failing to dispense fabric softener, or continuously dripping into the tub. Blue/white plastic with metal coil, 1/2" NPT thread, ~3"H x 4"W x 3"L. Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, AP6835737. Often paired with the hot water valve (W11688994, sold separately). Common Problems This Part Fixes Washer not filling with cold water — valve solenoid not opening when commanded Washer filling slowly with cold water — valve partially clogged or weak solenoid F8E1 error code displayed — cold water inlet valve fault LO FL (low flow) error code — valve unable to deliver normal water flow Fabric softener not being dispensed — cold water flush to dispenser failing Water continuously dripping into the tub when the washer is off — valve stuck open or not fully closing Water leaks at the valve body — internal seal failure Wash cycles taking much longer than normal due to slow fill Replaces Part Numbers This cold water inlet valve directly replaces the following OEM and cross-reference part numbers: W11688995, W11316256, W11036930, W11486361, 4983050, PD00086086, FIX17216730, EAP17216730, OEM28874414, AP7218603, AWP46809, PS17216730. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cold water inlet valve is compatible with select front-load washers from the following brands: Whirlpool front-load washers — WFC6810LW0, WFC9820HC0, WFC9820HW0 series Whirlpool front-load washers — WFW560CHW0, WFW560CHW1, WFW560CHW2, WFW560CHW3, WFW560CHW4 series Whirlpool front-load washers — WFW5605MC0, WFW5605MW0 series Whirlpool front-load washers — WFW5620HW0, WFW5620HW1, WFW5620HW2, WFW5620HW3 series Whirlpool front-load washers — WFW6620HC0, WFW6620HC1, WFW6620HC2, WFW6620HW0, WFW6620HW1 series Whirlpool front-load washers — WFW8620HC0, WFW8620HC1, WFW8620HC2, WFW8620HC3, WFW8620HC4, WFW8620HW0, WFW8620HW1, WFW8620HW2, WFW8620HW3, WFW8620HW4 series Whirlpool front-load washers — WFW862CHC0, WFW862CHC1, WFW862CHC2, WFW862CHC3 series Whirlpool front-load washers — WFW9620HBK1, WFW9620HBK2, WFW9620HBK3, WFW9620HC0, WFW9620HC1, WFW9620HC3, WFW9620HW0, WFW9620HW1, WFW9620HW2, WFW9620HW3 series Maytag front-load washers — MHW5630HC0, MHW5630HW1, MHW5630MBK0 series and related Amana front-load washers — NFW5800HW0, NFW5800HW1 and related models Inglis front-load washers — IFW5900HW, IFW5900HW1 and related models KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper front-load washers — select Whirlpool-built models Kenmore / Sears front-load washers — select Whirlpool-built models Note: This is the cold water inlet valve (typically blue). The matching hot water inlet valve is part number W11688994 (typically red). When you replace one valve, it's a good practice to replace the other at the same time since they're the same age, both are accessible during the same repair, and the second valve will likely fail in the near term. Always verify your model number before ordering. Key Features Aftermarket replacement built to OEM-equivalent quality standards Controls the flow of cold water into the washer during fill cycles Solenoid-actuated — opens precisely when the control board calls for cold water and closes the moment the call is dropped Resolves F8E1 and LO FL error codes when caused by a failed cold inlet valve 1/2" NPT threaded inlet for standard washer supply hose connection Dimensions: approximately 3" H x 4" W x 3" L Blue and white plastic body with metal solenoid coil — designed for long-term reliability against wash cycle pressure and temperature Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737 Compatible with Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers Often replaced together with the hot water inlet valve (W11688994, sold separately) as a paired repair Quick DIY repair — installs in 10–15 minutes with basic hand tools Product Specifications Part Number XPW11688995 Part Type Washer Water Inlet Valve (Cold) Condition Aftermarket Replacement Application Front-Load Washers (Whirlpool platform) Water Type Cold (paired hot valve is W11688994) Inlet Thread 1/2" NPT Dimensions Approximately 3" H x 4" W x 3" L Color Blue / White Material Plastic / Metal Error Codes Resolved F8E1, LO FL (when caused by cold valve fault) Often Paired With Hot Water Inlet Valve (W11688994, sold separately) Compatible Brands Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power and shut off both the hot and cold water supplies at the wall before beginning. Wear work gloves to protect your hands. Have towels ready — residual water remains in the supply hoses and will spill when disconnected. Pull the washer out from the wall to access the back. Remove the three 1/4" screws securing the rear edge of the top cover, push the top cover slightly back, and lift it off. Locate the inlet valves at the back of the washer — the cold valve is typically blue. Disconnect the cold water supply hose from the valve (water will drip — towels). Photograph the wire connections before disconnecting. Unplug the small electrical connector from the valve solenoid. Remove the single 3/16" mounting screw (or similar hardware, model-dependent) holding the valve in place, and disconnect any internal water hoses from the valve outlet (channel-lock pliers may help with hose clamps). Install the new W11688995 valve in the same position with the same orientation, reconnect the internal water hoses and electrical connector, and secure the mounting screw. Reconnect the cold supply hose at the wall, restore water and power, and run a test cycle to confirm normal cold water fill with no leaks. Tip: while the top cover is off, this is the ideal time to also replace the hot water valve (W11688994) — they share the same access and lifespan. Tools needed: 1/4" nut driver, 3/16" nut driver, adjustable wrench or pliers, work gloves. Frequently Asked Questions What do error codes F8E1 and LO FL mean on Whirlpool washers? Both codes indicate a water fill problem. F8E1 appears when the control board doesn't detect normal water flow during a fill cycle — typically caused by a failed inlet valve, a clogged inlet screen, kinked supply hose, or restricted water supply. LO FL (low flow) appears when the washer detects that water is flowing in, but at a rate too low to complete the fill within the expected time window. When the cold water inlet valve has failed or is partially clogged, both codes can appear together. Before replacing the valve, check that the household cold water supply is on and the supply hose isn't kinked, and inspect the inlet screen on the valve for sediment buildup. If those check out, replacing the W11688995 typically resolves the codes. My washer isn't dispensing fabric softener — could this be the cold valve? Yes — this is actually a common symptom that's often misdiagnosed. The cold water inlet valve also feeds the detergent dispenser tray on most Whirlpool front-load washers, including the fabric softener compartment. If the cold valve is clogged or failing to fully open at the right moment in the cycle, water doesn't flow through the fabric softener compartment to flush it into the tub, leaving softener pooled in the tray at the end of the cycle. If you've already cleaned the dispenser tray and water lines and the problem persists, replacing the cold inlet valve (W11688995) often resolves the issue. Should I replace the hot water valve at the same time? Yes, it's strongly recommended. The cold and hot inlet valves are essentially identical components installed side by side at the back of the washer — they're the same age, are exposed to the same wash cycle stress, and have the same expected service life. When one fails, the other is typically not far behind. Since the top cover is already off and both valves are accessible during the same repair, replacing both saves you a second teardown later. The matching hot water valve is part number W11688994 (red, sold separately) and is also available as a paired kit. My washer is dripping water into the tub even when it's off — is this the valve? Yes, that's a classic sign of a failed inlet valve. When the solenoid wears out or debris keeps the valve from sealing fully closed, water leaks past it at low rates and drips into the tub even with the washer powered off — especially noticeable as a slow puddle forming over a day or two. Since both the hot and cold valves feed into the tub, you'll want to identify which one is leaking: shut off the hot water supply at the wall and check if dripping continues. If it stops, the hot valve is at fault; if it continues, this cold valve is the cause. Replacing the W11688995 will resolve a leaking cold valve. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, electrical specifications, 1/2" NPT thread, and solenoid function of the original W11688995 cold water inlet valve used in compatible Whirlpool, Maytag, Amana, KitchenAid, and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11688995 (OE) Washer Water Inlet Valve (Cold) The XPARTCO W11688995 (OE — Original Equipment specification) is an aftermarket replacement cold water inlet valve built to OEM specifications, designed as a direct fit for select Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers. The cold water inlet valve is mounted at the back of the washer where the cold water supply hose connects. When the washer's control board calls for cold water during a wash cycle, the valve's internal solenoid opens, letting water flow into the tub or detergent dispenser. The valve closes the instant the control board cuts power, stopping flow precisely as the correct fill level is reached. When this valve fails, the washer may not fill with cold water at all, fill very slowly, fail to dispense fabric softener, continuously drip water into the tub even when off, or display F8E1 or LO FL error codes. Construction is blue and white plastic with metal solenoid coil, ~3"H x 4"W x 3"L, with 1/2" NPT threaded inlet for standard washer supply hose. It directly replaces W11688995, W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737. Often replaced as a pair with the hot water inlet valve (W11688994, sold separately). Installs in 10–15 minutes with basic hand tools. Quick Answer The XPARTCO W11688995 (OE) Washer Water Inlet Valve (Cold) fixes Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, and Kenmore front-load washers displaying F8E1 or LO FL error codes, not filling with cold water, filling slowly, failing to dispense fabric softener, or continuously dripping into the tub. Blue/white plastic with metal coil, 1/2" NPT thread, ~3"H x 4"W x 3"L. Aftermarket Original Equipment (OE) — built to OEM specs. Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, AP6835737. Often paired with the hot water valve (W11688994, sold separately). Common Problems This Part Fixes Washer not filling with cold water — valve solenoid not opening when commanded Washer filling slowly with cold water — valve partially clogged or weak solenoid F8E1 error code displayed — cold water inlet valve fault LO FL (low flow) error code — valve unable to deliver normal water flow Fabric softener not being dispensed — cold water flush to dispenser failing Water continuously dripping into the tub when the washer is off — valve stuck open or not fully closing Water leaks at the valve body — internal seal failure Wash cycles taking much longer than normal due to slow fill Replaces Part Numbers This cold water inlet valve directly replaces the following OEM and cross-reference part numbers: W11688995, W11316256, W11036930, W11486361, 4983050, PD00086086, FIX17216730, EAP17216730, OEM28874414, AP7218603, AWP46809, PS17216730. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cold water inlet valve is compatible with select front-load washers from the following brands: Whirlpool front-load washers — WFC6810LW0, WFC9820HC0, WFC9820HW0 series Whirlpool front-load washers — WFW560CHW0, WFW560CHW1, WFW560CHW2, WFW560CHW3, WFW560CHW4 series Whirlpool front-load washers — WFW5605MC0, WFW5605MW0 series Whirlpool front-load washers — WFW5620HW0, WFW5620HW1, WFW5620HW2, WFW5620HW3 series Whirlpool front-load washers — WFW6620HC0, WFW6620HC1, WFW6620HC2, WFW6620HW0, WFW6620HW1 series Whirlpool front-load washers — WFW8620HC0, WFW8620HC1, WFW8620HC2, WFW8620HC3, WFW8620HC4, WFW8620HW0, WFW8620HW1, WFW8620HW2, WFW8620HW3, WFW8620HW4 series Whirlpool front-load washers — WFW862CHC0, WFW862CHC1, WFW862CHC2, WFW862CHC3 series Whirlpool front-load washers — WFW9620HBK1, WFW9620HBK2, WFW9620HBK3, WFW9620HC0, WFW9620HC1, WFW9620HC3, WFW9620HW0, WFW9620HW1, WFW9620HW2, WFW9620HW3 series Maytag front-load washers — MHW5630HC0, MHW5630HW1, MHW5630MBK0 series and related Amana front-load washers — NFW5800HW0, NFW5800HW1 and related models Inglis front-load washers — IFW5900HW, IFW5900HW1 and related models KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper front-load washers — select Whirlpool-built models Kenmore / Sears front-load washers — select Whirlpool-built models Note: This is the cold water inlet valve (typically blue). The matching hot water inlet valve is part number W11688994 (typically red). When you replace one valve, it's a good practice to replace the other at the same time since they're the same age, both are accessible during the same repair, and the second valve will likely fail in the near term. Always verify your model number before ordering. Key Features Aftermarket Original Equipment (OE) replacement — built to OEM specifications for direct fit and performance Controls the flow of cold water into the washer during fill cycles Solenoid-actuated — opens precisely when the control board calls for cold water and closes the moment the call is dropped Resolves F8E1 and LO FL error codes when caused by a failed cold inlet valve 1/2" NPT threaded inlet for standard washer supply hose connection Dimensions: approximately 3" H x 4" W x 3" L Blue and white plastic body with metal solenoid coil — designed for long-term reliability against wash cycle pressure and temperature Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737 Compatible with Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers Often replaced together with the hot water inlet valve (W11688994, sold separately) as a paired repair Quick DIY repair — installs in 10–15 minutes with basic hand tools Product Specifications Part Number W11688995 Designation OE (Original Equipment specification) Part Type Washer Water Inlet Valve (Cold) Condition Aftermarket Replacement Application Front-Load Washers (Whirlpool platform) Water Type Cold (paired hot valve is W11688994) Inlet Thread 1/2" NPT Dimensions Approximately 3" H x 4" W x 3" L Color Blue / White Material Plastic / Metal Error Codes Resolved F8E1, LO FL (when caused by cold valve fault) Often Paired With Hot Water Inlet Valve (W11688994, sold separately) Compatible Brands Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power and shut off both the hot and cold water supplies at the wall before beginning. Wear work gloves to protect your hands. Have towels ready — residual water remains in the supply hoses and will spill when disconnected. Pull the washer out from the wall to access the back. Remove the three 1/4" screws securing the rear edge of the top cover, push the top cover slightly back, and lift it off. Locate the inlet valves at the back of the washer — the cold valve is typically blue. Disconnect the cold water supply hose from the valve (water will drip — towels). Photograph the wire connections before disconnecting. Unplug the small electrical connector from the valve solenoid. Remove the single 3/16" mounting screw (or similar hardware, model-dependent) holding the valve in place, and disconnect any internal water hoses from the valve outlet (channel-lock pliers may help with hose clamps). Install the new W11688995 valve in the same position with the same orientation, reconnect the internal water hoses and electrical connector, and secure the mounting screw. Reconnect the cold supply hose at the wall, restore water and power, and run a test cycle to confirm normal cold water fill with no leaks. Tip: while the top cover is off, this is the ideal time to also replace the hot water valve (W11688994) — they share the same access and lifespan. Tools needed: 1/4" nut driver, 3/16" nut driver, adjustable wrench or pliers, work gloves. Frequently Asked Questions What do error codes F8E1 and LO FL mean on Whirlpool washers? Both codes indicate a water fill problem. F8E1 appears when the control board doesn't detect normal water flow during a fill cycle — typically caused by a failed inlet valve, a clogged inlet screen, kinked supply hose, or restricted water supply. LO FL (low flow) appears when the washer detects that water is flowing in, but at a rate too low to complete the fill within the expected time window. When the cold water inlet valve has failed or is partially clogged, both codes can appear together. Before replacing the valve, check that the household cold water supply is on and the supply hose isn't kinked, and inspect the inlet screen on the valve for sediment buildup. If those check out, replacing the W11688995 typically resolves the codes. My washer isn't dispensing fabric softener — could this be the cold valve? Yes — this is actually a common symptom that's often misdiagnosed. The cold water inlet valve also feeds the detergent dispenser tray on most Whirlpool front-load washers, including the fabric softener compartment. If the cold valve is clogged or failing to fully open at the right moment in the cycle, water doesn't flow through the fabric softener compartment to flush it into the tub, leaving softener pooled in the tray at the end of the cycle. If you've already cleaned the dispenser tray and water lines and the problem persists, replacing the cold inlet valve (W11688995) often resolves the issue. Should I replace the hot water valve at the same time? Yes, it's strongly recommended. The cold and hot inlet valves are essentially identical components installed side by side at the back of the washer — they're the same age, are exposed to the same wash cycle stress, and have the same expected service life. When one fails, the other is typically not far behind. Since the top cover is already off and both valves are accessible during the same repair, replacing both saves you a second teardown later. The matching hot water valve is part number W11688994 (red, sold separately) and is also available as a paired kit. My washer is dripping water into the tub even when it's off — is this the valve? Yes, that's a classic sign of a failed inlet valve. When the solenoid wears out or debris keeps the valve from sealing fully closed, water leaks past it at low rates and drips into the tub even with the washer powered off — especially noticeable as a slow puddle forming over a day or two. Since both the hot and cold valves feed into the tub, you'll want to identify which one is leaking: shut off the hot water supply at the wall and check if dripping continues. If it stops, the hot valve is at fault; if it continues, this cold valve is the cause. Replacing the W11688995 will resolve a leaking cold valve. What does "OE" mean and how is this different from an OEM Whirlpool part? "OE" stands for Original Equipment — meaning this is an aftermarket replacement part manufactured to original equipment specifications. It is engineered as a direct-fit substitute matching the dimensions, electrical specifications, and function of the original Whirlpool W11688995. It is not a genuine Whirlpool-branded OEM part, but is built to the same quality standards and performs identically when installed in compatible washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM DA82-01415A Refrigerator Water Leakage Repair Kit The Genuine OEM Samsung DA82-01415A is a water leakage repair kit (also sold as a water leak service kit) for select Samsung bottom-freezer and French door refrigerators. It addresses water leaking from the defrost drain, where a frozen or poorly sealed drain lets ice build up on the evaporator and meltwater overflow under the crisper drawers. The kit includes a replacement drain tube with cap and foam sealing pieces for the evaporator drain plate. This is the original Samsung part, not an aftermarket equivalent. It is sold as a kit. Check your model number before ordering. Quick Answer The Genuine OEM DA82-01415A Water Leakage Repair Kit repairs the defrost drain on a compatible Samsung refrigerator that is leaking water. Classic symptoms: water pooling at the bottom of the refrigerator or under the crisper drawers, frost building up on the evaporator, or a frozen drain tube. Common Problems This Kit Fixes Water pooling at the bottom of the refrigerator or under the crisper drawers Condensate leaking around the evaporator Excess frost forming on the evaporator cover Frozen or iced-over defrost drain tube Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This water leakage repair kit is listed under the following part number: DA82-01415A replaces DA62-03441A, 3436781, AP5957964, ASM31603, EAP10058968, PD00024858, PS10058968 If your old kit shows a different number, contact our support team and we'll check whether it matches. Compatibility This kit is listed for Samsung bottom-freezer and French door refrigerators with dual evaporators. Retailers do not publish a full model list for this kit. Note: Samsung sells similar-looking leak kits and drain parts under different part numbers, and newer refrigerators may already have a factory-installed drain tube. Send us your full model number, or check it against your parts diagram, and we'll verify fit before you order. Key Features Genuine OEM Samsung part, not an aftermarket equivalent Replacement defrost drain tube with cap Foam sealing pieces for the evaporator drain plate Sold as a kit Product Specifications Part Number DA82-01415A OEM Part Number DA82-01415A Part Type Refrigerator Water Leakage Repair Kit Condition Genuine OEM Manufacturer Samsung Quantity 1 Kit Application Select Samsung Bottom-Freezer and French Door Refrigerators Installation Notes ⚠️ Disconnect Power Before Installing Unplug the refrigerator and remove any food that could spoil. Remove the evaporator cover and check that the defrost heater and defrost sensor work, because a failed heater or sensor will cause the drain to freeze again. Take care when moving the evaporator and drain plate, because damage to the evaporator coil can ruin the sealed system. Fit the new drain tube and foam seals, put the cover back, and fully thaw any ice in the drain before you restore power. Reviewers suggest having Phillips and flat-head screwdrivers and pliers on hand and consulting your model's service manual. Frequently Asked Questions My refrigerator is leaking water. Is this kit the fix? It can be, if the leak comes from a frozen or poorly sealed defrost drain. Before buying, check that the defrost heater and defrost sensor work, because a failed heater or sensor can cause the same leak. Is this an OEM or aftermarket part? This is a genuine OEM part from Samsung, not an aftermarket equivalent. What is in the kit? It includes a replacement drain tube with cap and foam sealing pieces for the evaporator drain plate. Retailers describe the full contents differently, so contact our support team if you need to confirm them before ordering. Will this fit my refrigerator? It is listed for Samsung bottom-freezer and French door refrigerators with dual evaporators, but no model list is published. Send us your full model number, or check it against your parts diagram, and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less