Search results for "Washer Sensor"

WH11X39237 Genuine OEM GE Washer Drain Pump The WH11X39237 is a Genuine OEM GE replacement drain pump and filter assembly compatible with select GE, GE Profile, and GE 2-in-1 Washer/Dryer Combo front-load washers in the GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series. The drain pump is responsible for removing water from the washer drum during the drain and spin cycles — when it fails, the washer will not drain, will leave standing water in the drum, or will produce unusual noises during the drain cycle. This complete drain pump and filter assembly operates at 120V, 60Hz, 1.2A and includes the pump motor, impeller housing, and integrated filter. It directly replaces the discontinued WH11X29539 — WH11X39237 is the current manufacturer-approved updated part number. Also replaces AP6986715, 4962370, B25-3A04, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools. Quick Answer The WH11X39237 Genuine OEM GE Washer Drain Pump fixes GE front-load washers that won't drain, leave standing water in the drum, display drain error codes, or make loud humming or grinding noises during the drain cycle. Complete pump and filter assembly. 120V/60Hz/1.2A. Replaces discontinued WH11X29539. Compatible with GE GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series. Common Problems This Part Fixes Washer not draining — standing water remaining in the drum after a cycle Drain error codes displayed on GE front-load washers (e.g. E23, E24, or pump-related codes) Loud humming, grinding, or buzzing noise during the drain cycle Washer stopping mid-cycle due to a drain fault Water leaking from around the drain pump area Drain pump running continuously but water not being expelled Pump impeller jammed by debris and motor burned out Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: WH11X39237, WH11X29539, Hanyu B25-3A04, 9019841, PD00094541, AGE1260100, AP8054992, PS18351790. WH11X39237 is the current manufacturer-approved replacement for the discontinued WH11X29539. If your appliance documentation lists WH11X29539, this is the correct updated part. Compatibility This drain pump is compatible with select front-load washers and laundry combos from the following GE product lines: GE front-load washers — GFW510 series GE front-load washers — GFW550 series GE front-load washers — GFW650 series GE front-load washers — GFW655 series GE front-load washers — GFW850 series GE Profile front-load washers — PFW870, PFW950, PFW955 series GE Profile front-load washers — PFQ83 series GE 2-in-1 Washer/Dryer Combo (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Complete drain pump and filter assembly — pump motor, impeller housing, and integrated filter all included Removes water from the drum during drain and spin cycles for proper washer operation Integrated filter traps lint, coins, and debris to prevent pump impeller damage and clogs Electrical specs: 120V, 60Hz, 1.2A — correct for compatible GE front-load models WH11X39237 is the current manufacturer-approved replacement for discontinued WH11X29539 Direct replacement — installs into existing pump housing with no modification required Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Compatible with GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series DIY-friendly repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number WH11X39237 Supersedes WH11X29539 (discontinued) Part Type Washer Drain Pump and Filter Assembly Condition Genuine OEM Application GE Front-Load Washers and 2-in-1 Washer/Dryer Combos Voltage 120V AC Frequency 60 Hz Amperage 1.2A Includes Pump motor, impeller housing, and integrated filter Compatible Series GFW510, GFW550, GFW650, GFW655, GFW850, PFW870, PFW950, PFW955, PFQ83 Compatible Brands GE, GE Profile Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Place towels and a shallow pan under the pump access area to catch residual water. Remove the front lower access panel of the washer. Before removing the pump, first clean the pump filter (WH23X38617) and check for a clogged filter or debris in the pump housing — a jammed impeller is sometimes mistaken for a failed pump. If the pump motor is confirmed failed, disconnect the wire harness and drain hoses from the old pump assembly, then unscrew or unclip the pump from the mounting bracket. Install the new WH11X39237 pump assembly, reconnect the drain hoses and secure with clamps, reconnect the wire harness, and reinstall the access panel. Restore power and water supply, then run a drain-only cycle to verify proper drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan or towels. Frequently Asked Questions What is the difference between WH11X39237 and WH11X29539? These are the same drain pump assembly — WH11X39237 is the current updated part number that GE issued to replace the discontinued WH11X29539. If your washer's documentation, parts diagram, or old pump label shows WH11X29539, the WH11X39237 is the correct replacement to order. Should I check the pump filter before replacing the drain pump? Yes — always check and clean the pump filter (WH23X38617) before replacing the drain pump. A heavily clogged filter can restrict water flow enough to mimic pump failure symptoms, and a foreign object jammed in the impeller can stall the pump motor without permanently damaging it. Remove the filter, clear any debris from the housing and impeller, and test the washer again. If the pump still fails to drain after cleaning, then pump replacement is the next step. How do I know if my drain pump has failed? A failed drain pump typically causes the washer to stop mid-cycle with a drain error code, or to finish a cycle with standing water in the drum. You may also hear a loud humming noise during the drain phase — this indicates the motor is running but the impeller is not turning (jammed or broken). A grinding noise suggests physical damage to the impeller or pump housing. If the pump is completely silent during the drain cycle despite power being delivered to it, the motor has likely burned out. Is the WH11X39237 compatible with GE Profile and GE 2-in-1 models? Yes — the WH11X39237 is compatible with select GE Profile front-load washers in the PFW870, PFW950, PFW955, and PFQ83 series, as well as select GE 2-in-1 Washer/Dryer Combo models. Always verify your specific model number before ordering to confirm compatibility. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same drain pump and filter assembly installed in compatible GE and GE Profile front-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH01X20826 Washing Machine Shock Absorber The XPARTCO WH01X20826 is an aftermarket replacement shock absorber (damper) for GE front-load washers. The wash tub inside a front-load washer hangs suspended inside the cabinet, and a set of these shock absorbers is what controls that movement — dampening the tub's vibration and motion during spin so it doesn't bang against the cabinet or shake the whole machine. These washers typically use four shock absorbers working together around the tub, and this listing is for a single individual shock absorber. Over time the internal damping material in these shocks wears out, or the shock can physically separate from its mounting point — something that can also happen if the washer is moved or shifted without the tub properly secured first. Because all four shocks on a given washer are typically the same age and under the same stress, if one has failed the others are often not far behind — many technicians recommend ordering four of this same part and replacing the full set together as a preventative measure. A worn or detached shock absorber produces a very recognizable symptom: excessive vibration, shaking, or banging noise during the spin cycle, sometimes strong enough that the washer visibly moves or "walks" across the floor. It directly replaces WH01X20826, AGE25988, AP5982139, AGE25988, EAP11701130, PD00037528, PS11701130. Quick Answer The XPARTCO WH01X20826 Washing Machine Shock Absorber fixes GE front-load washers (and select Hotpoint, Haier, Monogram, Café, and Kenmore models built on the GE platform) that vibrate, shake, or bang excessively during spin, or seem to "walk" across the floor. Sold as a single individual shock absorber. Replaces WH01X20826, AGE25988, AP5982139, AGE25988, EAP11701130, PD00037528, PS11701130. These washers use four shock absorbers total — if one has failed, order four of this part to replace the full set, since they wear on the same schedule. Common Problems This Part Fixes Excessive vibration or shaking during the spin cycle Loud banging or knocking noise from inside the cabinet during spin Washer that seems to "walk" or move across the floor during operation Tub striking the cabinet frame or nearby panels Shock absorber that has visibly separated or detached from its mounting point Noise or vibration that started or worsened after the washer was moved or relocated Visible wear, cracking, or looseness in the shock absorber material Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washing machine shock absorber directly replaces the following OEM and cross-reference part numbers: WH01X20826, AGE25988, AP5982139, AGE25988, EAP11701130, PD00037528, PS11701130 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This shock absorber is compatible with select GE front-load washers, and also fits select Hotpoint, Haier, Monogram, and Café washers built on the GE platform. Note: GE uses several different shock absorber part numbers across its washer lineup, including separate parts such as WH01X10727 and WH03X29516 for other platforms. This WH01X20826 shock is specific to the front-load models listed above and is not interchangeable with those other GE shocks. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement shock absorber — dampens tub vibration and movement during spin Sold individually — order four to replace the full set on a typical front-load washer Resolves "excessive vibration," "banging or knocking noise," and "washer walking across the floor" symptoms caused by worn or detached shocks Durable plastic and rubber construction for long-term damping performance Direct drop-in replacement — no modification required Replaces WH01X20826, AGE25988, AP5982139, AGE25988, EAP11701130, PD00037528, PS11701130. Compatible with GE, Hotpoint, Haier, Monogram, Café, and select Kenmore front-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPWH01X20826 OEM Part Number WH01X20826 Part Type Washing Machine Shock Absorber (Damper) Condition Aftermarket Replacement Application GE Front-Load Washers Material Plastic and rubber Function Dampens tub vibration and movement during spin Typical Quantity Per Washer 4 (this listing is for 1 individual shock) Quantity 1 shock absorber Compatible Brands GE, Hotpoint, Haier, Monogram, Café, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Consider Replacing All Four Shocks Together Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access to the shock absorbers typically requires removing the top and/or front panel of the washer to reach the tub suspension points — check your model's service diagram, since access varies. Photograph how each old shock absorber connects to the frame and the tub before removing anything, since these components are symmetrical around the tub and easy to reverse or mismatch. Disconnect the old shock absorber from its mounting point at both the frame and tub ends, and remove the mounting pin. Install the new shock absorber in the same position with its mounting pin, matching the original orientation. If you're only replacing one shock, be aware the remaining three original shocks are the same age and under the same stress — many technicians recommend ordering three more of this same part and replacing all four together to avoid reopening the washer again soon after. Once installed, gently rock the tub by hand to confirm even resistance at each corner before reassembling the panels. Restore power and run a full spin cycle to confirm the vibration, shaking, or banging noise has resolved. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions Do I need to order more than one of these? This listing is for a single shock absorber, but GE front-load washers use four of them working together around the tub. If one has failed, it's strongly worth ordering four total and replacing the full set, since all four are typically the same age and have been under the same stress — replacing just one risks having to reopen the washer again soon after for the next one. My washer started shaking right after I moved it to a new spot. Is that related? Yes, this is a documented cause of shock absorber problems on this platform. If the tub wasn't properly secured or the washer was tilted significantly during a move, one or more shock absorbers can separate from their mounting point. Check that all four shocks are still properly connected at both ends before assuming a shock itself has failed — sometimes reseating a separated shock is all that's needed, though if it shows wear it's worth replacing regardless. How much vibration is normal, and how do I know it's actually the shocks? Some vibration during high-speed spin is normal, especially with an unbalanced load. But vibration strong enough to move the washer across the floor, or accompanied by a banging or knocking noise from inside the cabinet, points to a suspension problem rather than a simple unbalanced load. Try redistributing the laundry evenly in the drum and running the spin cycle again — if the shaking persists with a balanced load, inspect the shock absorbers for wear, cracking, or separation. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the dimensions, mounting configuration, and damping performance of the original WH01X20826 shock absorber used in compatible GE, Hotpoint, Haier, Monogram, Café, and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH23X28418 Washer Genuine GE OEM Drain Pump The WH23X28418 is a Genuine GE OEM replacement drain pump and motor assembly compatible with select GE, Hotpoint, Haier, RCA, and Kenmore top-load and front-load washers. The drain pump removes water from the washer drum during the drain and spin cycles — expelling water and detergent through the drain hose so that clothing comes out clean and free of excess water. When the pump fails, the washer will not drain, may leave standing water in the tub, or may produce loud noises during the drain cycle. This complete drain pump and motor assembly is rated at 120V, 60Hz, 1.25A with a duty cycle of 10 minutes on and 50 minutes off. It includes the pump and motor with harness — the harness and plug extend approximately 10 inches from the motor. The pump measures 5-1/4" L x 5-1/8" W x 5-1/2" H and includes a drain pump seal. It directly replaces WH23X24178 and WH23X27574, as well as several additional cross-reference numbers. Installs in 20–40 minutes with basic hand tools. Quick Answer The WH23X28418 Washer Genuine GE OEM Drain Pump fixes GE, Hotpoint, Haier, and RCA washers that won't drain, leave standing water in the tub, are noisy during draining, or leak around the pump area. Complete pump and motor with harness and drain pump seal. 120V/60Hz/1.25A. Dimensions 5-1/4" L x 5-1/8" W x 5-1/2" H; harness extends approx. 10". Replaces WH23X24178 and WH23X27574. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Washer stopping mid-cycle due to a drain fault or drain-related error code Loud humming, grinding, or buzzing noise during the drain cycle Washer pumps but will not spin — pump failure preventing cycle completion Water leaking from around the drain pump area Clothes not clean or coming out soaking wet due to incomplete drainage Pump impeller jammed by debris causing motor burnout Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: WH23X24178, WH23X28418, WH23X27574, 290D1201G001, 290D1201G002, 290D1201G003, AGE26155, B40-3A01, B30-3A02, PD00055680, EAP12723115, AP6889136, PS12723115. WH23X28418 is the current updated part number replacing the discontinued WH23X24178 and WH23X27574. If your washer documentation or old pump label shows either of those numbers, this is the correct replacement. Compatibility This drain pump is compatible with select washers from the following brands and series: GE top-load washers — GTW220, GTW330, GTW335, GTW460, GTW465, GTW485, GTW490, GTW500, GTW680, GTW720, GTW725, GTW750 series and others GE front-load washers — select GFW series models Hotpoint top-load washers — HTW200, HTW240 series and others Haier top-load washers — select models RCA top-load washers — select models Kenmore / Sears washers — select GE-built models Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Removes water and detergent from the washer drum during drain and spin cycles Complete assembly — includes pump motor, harness, and drain pump seal Rated 120V, 60Hz, 1.25A with a 10-minute on / 50-minute off duty cycle Dimensions: 5-1/4" L x 5-1/8" W x 5-1/2" H; harness and plug extend approximately 10" from motor Plastic and metal construction rated CL.A — durable and chemical resistant Includes drain pump seal to prevent leaks at the pump connection Current updated replacement for discontinued WH23X24178 and WH23X27574 — direct fit Note: The drain pump motor has been redesigned by the manufacturer — the replacement may look different from the original but fits and functions identically Genuine GE OEM part — factory-exact fit, materials, and specifications DIY-friendly repair — installs in 20–40 minutes with basic hand tools Product Specifications Part Number WH23X28418 Supersedes WH23X24178, WH23X27574 (both discontinued) Part Type Washer Drain Pump and Motor Assembly Condition Genuine OEM Application GE, Hotpoint, Haier, RCA Top-Load and Front-Load Washers Voltage 120V AC Frequency 60 Hz Amperage 1.25A Rating CL.A Duty Cycle 10 minutes ON / 50 minutes OFF Dimensions 5-1/4" L x 5-1/8" W x 5-1/2" H Harness Length Approximately 10 inches from motor Color White / Black / Gray Material Plastic / Metal Includes Pump and motor with harness, drain pump seal Compatible Brands GE, Hotpoint, Haier, RCA, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Have towels and a shallow pan ready to catch residual water. For top-load GE washers, the drain pump is typically accessed from the bottom of the machine — carefully tilt the washer back onto a support or lay it on its side to reach the pump from underneath. Disconnect the outlet hose by loosening the hose clamp and pulling it free. Disconnect the electrical harness connector. Remove the mounting screws (typically three) securing the pump to the washer base. Twist and firmly pull the old pump out. Install the new WH23X28418 pump in reverse order — connect the hose, tighten the clamp, reconnect the harness, and secure the mounting screws. Restore power and water supply and run a test cycle to verify proper drainage and no leaks. Tools needed: Phillips screwdriver, flat-head screwdriver, slip-joint pliers, shallow pan. Frequently Asked Questions What is the relationship between WH23X28418, WH23X24178, and WH23X27574? All three are GE washer drain pumps — WH23X28418 is the current updated part number that replaced both the discontinued WH23X24178 and WH23X27574. GE redesigned the pump motor during its production cycle, so the replacement may look slightly different from the original, but it fits and functions identically. If your washer uses either of the older numbers, order WH23X28418. How do I know if my washer drain pump has failed? The most common signs are standing water in the tub after a cycle, the washer stopping mid-cycle with a drain error, or loud humming during the drain phase — which indicates the motor is running but the impeller is not moving. A grinding or rattling noise suggests debris in the pump or physical damage. If the pump is completely silent during what should be the drain cycle, the motor has likely burned out and the pump needs replacement. Does the WH23X28418 fit both top-load and front-load GE washers? The WH23X28418 is primarily used in GE and Hotpoint top-load washers — the GTW and HTW series make up the majority of compatible models. It also fits select GE front-load models. Always verify your specific model number before ordering to confirm compatibility for your washer type. What is the duty cycle rating and why does it matter? The duty cycle of 10 minutes on / 50 minutes off means the pump motor is rated for up to 10 consecutive minutes of operation before requiring a 50-minute rest period. In normal washer operation this is never an issue — drain cycles are brief. However, if a drain fault causes the pump to run continuously without successfully draining, the motor can overheat. If you replace the pump due to burnout and the new pump also fails quickly, check for a drain hose blockage or control board fault that may be causing the pump to run without limit. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications — the exact same drain pump and motor assembly installed in compatible models from the factory, with guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

AHA72973309 Genuine OEM LG Washer Drain & Circulation Pump Assembly The AHA72973309 is a genuine LG OEM drain and circulation pump assembly for LG and select Kenmore front-load washers. This is a dual-purpose pump — an Askoll M120-2 unit — that handles two separate jobs from one motor and housing. During the drain portion of the cycle, it pumps wastewater out of the tub and out through the drain hose. During the wash and rinse portions, it switches roles and recirculates water from the bottom of the tub back up through the dispenser and spray nozzle, showering it back over the load. That recirculation spray is what lets LG's front-load washers clean effectively with less water than an older top-load design would need. Because this single assembly performs both functions, a failure here can show up in more than one way: standing water left in the tub after a cycle, a washer that won't complete its drain step, unusual grinding or humming noise, or reduced wash performance if the recirculation spray isn't working even though draining still seems fine. Common causes include debris such as coins, buttons, or lint lodged in the impeller, general wear and tear on the motor bearings, or an electrical failure in the pump motor itself. It directly replaces AP5676608, 2659237, AHA72973304, and PS7788830. As a genuine OEM part, the AHA72973309 is manufactured by LG to factory specifications — guaranteed fit, materials, and performance. Quick Answer The AHA72973309 Genuine OEM LG Washer Drain & Circulation Pump Assembly fixes LG and select Kenmore front-load washers with standing water left in the tub after a cycle, a washer that won't drain, unusual grinding or humming noise, or reduced wash performance from a weak recirculation spray. Askoll M120-2 dual-purpose pump — handles both draining and mid-cycle water recirculation. Replaces AP5676608, 2659237, AHA72973304, PS7788830. Installation is average difficulty, 30 to 60 minutes — and on many models it's accessible through the front panel without needing to tip the washer over. Common Problems This Part Fixes Standing water left in the tub after a cycle finishes Washer won't drain, or drains very slowly Drainage-related error code displayed on the control panel Unusual grinding, humming, or rattling noise during the drain or wash portion of the cycle Reduced wash performance — clothes not getting as clean, possibly from a weak recirculation spray Washer stalling mid-cycle at the drain step Water leaking from underneath the washer near the pump housing Pump that hums but doesn't seem to move water — possible clog or seized impeller Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drain and circulation pump assembly directly replaces the following OEM and cross-reference part numbers: AHA72973309, AHA72973304, AP5676608, 2659237, ALG53336, PD00024680, PS7788830 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain and circulation pump assembly is compatible with select LG front-load washers, and also fits select Kenmore and Kenmore Elite front-load washers built on the LG platform. Note: This is a dual-function drain-and-circulation assembly specific to LG's front-load platform, built around the Askoll M120-2 pump. It is not a drain-only pump, and it is not intended for top-load washers, which use a different pump design. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine LG OEM part — factory-specified motor, impeller, and housing design Dual-purpose Askoll M120-2 pump — drains the tub and recirculates wash water through the dispenser spray nozzle Resolves "standing water in the tub," "won't drain," "grinding or humming noise," and "reduced wash performance" symptoms caused by pump failure Includes all necessary wiring and mounting hardware for a complete replacement Direct drop-in replacement — no modification required Replaces AP5676608, 2659237, AHA72973304, and PS7788830 Compatible with LG and select Kenmore/Kenmore Elite front-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Average installation difficulty — typically 30 to 60 minutes Product Specifications Part Number AHA72973309 Part Type Washer Drain & Circulation Pump Assembly Condition Genuine OEM Brand LG Pump Model Askoll M120-2 Function Drains tub water and recirculates wash water through the dispenser spray Kit Contents Pump assembly with wiring and mounting hardware Application Front-Load Washers (LG-Built) Repair Difficulty Average — 30 to 60 minutes Quantity 1 pump assembly Compatible Brands LG, select Kenmore, Kenmore Elite Installation Notes ⚠️ Unplug Washer And Shut Off Water Before Starting — Drain Residual Water First Disconnect power at the outlet or shut off the circuit breaker, and close the water supply valves before beginning. Wear work gloves. Place towels down and have a shallow pan ready, since the pump housing will hold residual water even after a completed cycle — draining this into a pan before disconnecting hoses will save you a mess. On many models, this pump is fully accessible by removing the front lower access panel or kick plate, without needing to tip the washer onto its back — check this first, since it can save significant time and effort compared to some online guides that recommend tipping the unit. Photograph the hose routing and wiring connections before disconnecting anything. Disconnect the two hose clamps connecting the pump to the tub and drain hose, and unplug the electrical connector from the pump motor. Remove the mounting screws or clips securing the pump assembly and lift it free, checking the impeller area for coins, buttons, or debris while it's out — clearing a clog here may have been the actual cause of the original symptom. Install the new AHA72973309 in the same orientation, reconnect both hoses with their clamps, and reconnect the electrical connector fully. Reinstall the front access panel, restore water and power, and run a short cycle to confirm normal draining, recirculation spray, and no leaks around the pump housing. Tools needed: Phillips screwdriver, hose clamp pliers, shallow pan or towels, work gloves. Frequently Asked Questions Do I really need to tip the washer over to replace this pump? Not necessarily — check your model first. While a lot of general online guidance recommends tipping the washer onto its back to access the pump from underneath, many LG and Kenmore Elite front-load models make this pump fully accessible through the front lower access panel or kick plate instead, without any tipping required. It's worth removing that panel first and seeing what you find before committing to the more involved tip-over approach. Why does this one pump handle both draining and something during the wash cycle? LG's front-load washers use this same Askoll pump for two different jobs at different points in the cycle: pumping wastewater out during the drain step, and recirculating water from the bottom of the tub back up through the dispenser and spray nozzle during wash and rinse to shower it over the load. That recirculation spray is part of how these washers clean effectively while using less water than an older top-load design. Because one pump does both jobs, a failure can affect draining, wash performance, or both, depending on what's actually gone wrong inside it. There's water left in the tub after every cycle. Is this definitely the pump? It's one of the most common causes, but check the easy things first. A clogged drain filter or a kinked drain hose can produce the same "won't drain" symptom and cost nothing to fix. If the filter and hose are clear and water is still standing in the tub, or if the pump hums but doesn't seem to move any water, the pump assembly itself has likely failed. My washer drains fine but clothes aren't coming out as clean. Could this pump be the cause? Possibly. Since this same assembly also handles the recirculation spray during wash, a partial failure can leave draining intact while weakening or eliminating that spray function, which reduces how effectively detergent and water reach the load. If drainage is normal but wash performance has noticeably declined, it's worth having this pump checked as one possible cause alongside things like detergent dosing and water hardness. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It includes the same Askoll M120-2 dual-function pump design, wiring, and mounting configuration as the drain and circulation pump assembly originally installed in your front-load washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 8182703 Washer Shock Absorber Replaces WP8182703 The XPARTCO 8182703 is an aftermarket replacement front-load washer shock absorber compatible with select Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, and Roper front-load washers in the GHW, WFW, MHWE, MFW, and KHWS series. The shock absorber is a hydraulic dampener that connects the outer washer tub to the base frame. During the spin cycle, the shock absorbers absorb and dampen the vibrations and movement generated by the spinning drum — keeping the washer stable, quiet, and protecting internal components from damage caused by excessive movement. Most compatible Whirlpool-family front-load washers use four shock absorbers — two at the front and two at the rear. When one or more shock absorbers wear out, the outer tub vibrates excessively, causing loud banging or thumping during the spin cycle. It is strongly recommended to replace all four shock absorbers at the same time. This listing is for a single shock absorber. It directly replaces WP8182703, 8181646, 1173231, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 8182703 Washer Shock Absorber fixes front-load washers that shake violently, bang loudly, or walk across the floor during the spin cycle. The shock absorber dampens tub vibration. Most models use 4 shock absorbers — replace all 4 at the same time. Sold individually. Compatible with Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, and Roper front-load washers. Replaces WP8182703, 8181646, AP6011831, and more. Common Problems This Part Fixes Violent shaking or vibrating during the spin cycle Loud banging, thumping, or clunking noise during spin Washer "walking" across the floor during the spin cycle Outer tub hitting the sides of the cabinet during high-speed spin Spin cycle errors caused by excessive tub movement triggering the imbalance sensor Visible oil leak, broken mount, or collapsed shock absorber body Washer repeatedly pausing spin cycle and redistributing the load without resolving the vibration Replaces Part Numbers This shock absorber directly replaces the following OEM and cross-reference part numbers: WP8182703, 8182703, 1173231, 8181646, EAP11745030, AWP48892, PD00003153, AP6011831, PS11745030. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This shock absorber is compatible with select front-load washers from the following brands and series: Whirlpool front-load washers — GHW and WFW series Maytag front-load washers — MHWE and MFW series Kenmore / Sears front-load washers (select Whirlpool-built models) KitchenAid front-load washers — KHWS series Amana front-load washers Jenn-Air front-load washers Admiral front-load washers Roper front-load washers Important: Most compatible models use 4 shock absorbers (2 front, 2 rear). This part is sold individually. It is strongly recommended to replace all 4 at the same time, as the remaining absorbers have experienced the same wear and will fail soon after. Key Features Hydraulic dampener that connects the outer washer tub to the base frame — absorbs spin cycle vibration and prevents tub-to-cabinet contact Keeps the washer stable and quiet during high-speed spin cycles, protecting drum bearings, seals, and cabinet from premature wear High-quality reinforced construction — excellent toughness, oil resistance, and resistance to weak acids and alkalis for long service life Direct replacement for WP8182703 and 8181646 — no modification required Compatible with Whirlpool GHW, WFW, Maytag MHWE, MFW, and KitchenAid KHWS series front-load washers Sold individually — most models require 4 shock absorbers; replace all 4 at the same time Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number 8182703 OEM Part Number WP8182703 Part Type Front-Load Washer Shock Absorber (Hydraulic Dampener) Condition Aftermarket Replacement Application Front-Load Washers Quantity Per Washer 4 (2 front, 2 rear) — sold individually Compatible Brands Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, Roper Compatible Series GHW, WFW, MHWE, MFW, KHWS Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Unplug the washer and turn off the water supply before beginning. To access the front shock absorbers, remove the lower front access panel. To access the rear shock absorbers, pull the washer away from the wall, disconnect the water hoses, and remove the rear panel. The shock absorbers connect the outer tub to the base frame with mounting pins at the top and bottom — turn the shock absorber 90 degrees at both pins to release and remove it. Install the new 8182703 shock absorber by inserting the pins into the top and bottom mounting brackets and rotating 90 degrees to lock in place. Replace all 4 shock absorbers during the same repair. Reconnect all panels and water hoses, plug in the washer, restore water supply, and run a spin cycle to verify normal operation. Work gloves are recommended as there are sharp edges inside the cabinet. Tools needed: Phillips screwdriver, channel-lock pliers, work gloves. Frequently Asked Questions What does the washer shock absorber do? The shock absorbers are hydraulic dampeners that connect the outer washer tub to the base frame of the machine. During the spin cycle — when the drum spins at high speeds — the shock absorbers absorb and dampen the vibrations and movement of the heavy outer tub, keeping it centered and preventing it from striking the sides of the washer cabinet. Without functioning shock absorbers, the washer vibrates violently, makes loud banging noises, and can "walk" across the floor during spin, potentially damaging internal components over time. How many shock absorbers does my front-load washer have? Most Whirlpool-family front-load washers compatible with the 8182703 shock absorber use four shock absorbers — two mounted at the front of the tub and two at the rear. This listing is for a single shock absorber. When replacing shock absorbers, it is strongly recommended to replace all four at once, as they all experience the same amount of use and the remaining absorbers are likely to fail soon after the first one. What is the difference between 8182703 and WP8182703? These are the same shock absorber. WP8182703 is the updated Whirlpool OEM part number that superseded the original 8182703. The 8181646 is also a cross-reference to this same part. This aftermarket replacement is compatible with all three numbers. My washer still vibrates after replacing the shock absorbers — what else could it be? If vibration persists after replacing all four shock absorbers, other possible causes include an unbalanced or overloaded drum, worn drum bearings, a failing suspension spring, or the washer not being level on the floor. Check that the washer's leveling feet are adjusted so all four corners are in firm contact with the floor. Also confirm the load is not oversized — overloading is the most common cause of spin vibration and can prematurely wear shock absorbers. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from high-quality reinforced materials to match the dimensions and performance of the original WP8182703 shock absorber. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

WH23X10026 Washer Genuine OEM Drain Pump Description: The GE drain pump assembly is an OEM replacement part responsible for removing wastewater, including dirty water and detergent residue, from the washer's tub during the drain cycle. This pump assembly consists of a motor and an impeller, which removes dirty water through the drain hose and out of the appliance. This part ensures that the washing machine efficiently drains water, allowing for the completion of the laundry cycle. Replaces Part Numbers: WH23X10028, WH23X10026, WH23X10037, AP4324598, AH1766031, EA1766031, PS1766031.   California Residents only WARNING: California’s Proposition 65 

Read more less

4 Pack - XPARTCO 8182703 Washer Shock Absorber Replaces WP8182703 The XPARTCO 8182703 is an aftermarket replacement front-load washer shock absorber compatible with select Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, and Roper front-load washers in the GHW, WFW, MHWE, MFW, and KHWS series. The shock absorber is a hydraulic dampener that connects the outer washer tub to the base frame. During the spin cycle, the shock absorbers absorb and dampen the vibrations and movement generated by the spinning drum — keeping the washer stable, quiet, and protecting internal components from damage caused by excessive movement. Most compatible Whirlpool-family front-load washers use four shock absorbers — two at the front and two at the rear. When one or more shock absorbers wear out, the outer tub vibrates excessively, causing loud banging or thumping during the spin cycle. It is strongly recommended to replace all four shock absorbers at the same time. This listing is for a single shock absorber. It directly replaces WP8182703, 8181646, 1173231, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 8182703 Washer Shock Absorber fixes front-load washers that shake violently, bang loudly, or walk across the floor during the spin cycle. The shock absorber dampens tub vibration. Most models use 4 shock absorbers — replace all 4 at the same time. Sold individually. Compatible with Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, and Roper front-load washers. Replaces WP8182703, 8181646, AP6011831, and more. Common Problems This Part Fixes Violent shaking or vibrating during the spin cycle Loud banging, thumping, or clunking noise during spin Washer "walking" across the floor during the spin cycle Outer tub hitting the sides of the cabinet during high-speed spin Spin cycle errors caused by excessive tub movement triggering the imbalance sensor Visible oil leak, broken mount, or collapsed shock absorber body Washer repeatedly pausing spin cycle and redistributing the load without resolving the vibration Replaces Part Numbers This shock absorber directly replaces the following OEM and cross-reference part numbers: WP8182703, 8182703, 1173231, 8181646, EAP11745030, AWP48892, PD00003153, AP6011831, PS11745030. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This shock absorber is compatible with select front-load washers from the following brands and series: Whirlpool front-load washers — GHW and WFW series Maytag front-load washers — MHWE and MFW series Kenmore / Sears front-load washers (select Whirlpool-built models) KitchenAid front-load washers — KHWS series Amana front-load washers Jenn-Air front-load washers Admiral front-load washers Roper front-load washers Important: Most compatible models use 4 shock absorbers (2 front, 2 rear). This part is sold individually. It is strongly recommended to replace all 4 at the same time, as the remaining absorbers have experienced the same wear and will fail soon after. Key Features Hydraulic dampener that connects the outer washer tub to the base frame — absorbs spin cycle vibration and prevents tub-to-cabinet contact Keeps the washer stable and quiet during high-speed spin cycles, protecting drum bearings, seals, and cabinet from premature wear High-quality reinforced construction — excellent toughness, oil resistance, and resistance to weak acids and alkalis for long service life Direct replacement for WP8182703 and 8181646 — no modification required Compatible with Whirlpool GHW, WFW, Maytag MHWE, MFW, and KitchenAid KHWS series front-load washers Sold individually — most models require 4 shock absorbers; replace all 4 at the same time Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number 8182703-4PK OEM Part Number WP8182703 Part Type Front-Load Washer Shock Absorber (Hydraulic Dampener) Condition Aftermarket Replacement Application Front-Load Washers Quantity Per Washer 4 (2 front, 2 rear) Compatible Brands Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, Roper Compatible Series GHW, WFW, MHWE, MFW, KHWS Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Unplug the washer and turn off the water supply before beginning. To access the front shock absorbers, remove the lower front access panel. To access the rear shock absorbers, pull the washer away from the wall, disconnect the water hoses, and remove the rear panel. The shock absorbers connect the outer tub to the base frame with mounting pins at the top and bottom — turn the shock absorber 90 degrees at both pins to release and remove it. Install the new 8182703 shock absorber by inserting the pins into the top and bottom mounting brackets and rotating 90 degrees to lock in place. Replace all 4 shock absorbers during the same repair. Reconnect all panels and water hoses, plug in the washer, restore water supply, and run a spin cycle to verify normal operation. Work gloves are recommended as there are sharp edges inside the cabinet. Tools needed: Phillips screwdriver, channel-lock pliers, work gloves. Frequently Asked Questions What does the washer shock absorber do? The shock absorbers are hydraulic dampeners that connect the outer washer tub to the base frame of the machine. During the spin cycle — when the drum spins at high speeds — the shock absorbers absorb and dampen the vibrations and movement of the heavy outer tub, keeping it centered and preventing it from striking the sides of the washer cabinet. Without functioning shock absorbers, the washer vibrates violently, makes loud banging noises, and can "walk" across the floor during spin, potentially damaging internal components over time. How many shock absorbers does my front-load washer have? Most Whirlpool-family front-load washers compatible with the 8182703 shock absorber use four shock absorbers — two mounted at the front of the tub and two at the rear. This listing is for a single shock absorber. When replacing shock absorbers, it is strongly recommended to replace all four at once, as they all experience the same amount of use and the remaining absorbers are likely to fail soon after the first one. What is the difference between 8182703 and WP8182703? These are the same shock absorber. WP8182703 is the updated Whirlpool OEM part number that superseded the original 8182703. The 8181646 is also a cross-reference to this same part. This aftermarket replacement is compatible with all three numbers. My washer still vibrates after replacing the shock absorbers — what else could it be? If vibration persists after replacing all four shock absorbers, other possible causes include an unbalanced or overloaded drum, worn drum bearings, a failing suspension spring, or the washer not being level on the floor. Check that the washer's leveling feet are adjusted so all four corners are in firm contact with the floor. Also confirm the load is not oversized — overloading is the most common cause of spin vibration and can prematurely wear shock absorbers. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from high-quality reinforced materials to match the dimensions and performance of the original WP8182703 shock absorber. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO WR55X10025 Refrigerator Temperature Sensor The XPARTCO WR55X10025 is an aftermarket replacement refrigerator temperature sensor (thermistor) compatible with a wide range of GE, Hotpoint, Haier, Café, and Monogram refrigerators. The temperature sensor monitors air temperature inside the fresh food and freezer compartments and sends that data to the main control board, which uses it to regulate cooling cycles and maintain the correct set temperature. When the sensor fails, the refrigerator may run too warm, too cold, or experience erratic defrost behavior. This sensor measures approximately 1-1/4 inches long and includes 18-inch wire leads. It is constructed from white plastic and is used in both fresh food and freezer compartments depending on the model — on some models it also functions as a defrost sensor on the evaporator coil. It directly replaces OEM part numbers WR55X10025 and a large number of earlier GE thermistor part numbers. Sold individually — some models require two sensors. Installs in under 30 minutes with basic hand tools. Quick Answer The XPARTCO WR55X10025 Refrigerator Temperature Sensor fixes GE and Hotpoint refrigerators that are too warm, too cold, not defrosting, or over-defrosting. The thermistor monitors compartment temperature and communicates with the control board. Approx. 1-1/4" long with 18" leads, white plastic. Compatible with GE, Hotpoint, Haier, Café, and Monogram refrigerators. Sold individually. Common Problems This Part Fixes Refrigerator compartment running too warm — food spoiling faster than normal Refrigerator running too cold — food or liquids freezing in the fresh food section Freezer section not maintaining correct temperature Refrigerator not defrosting or defrosting too frequently Excessive frost or ice buildup on evaporator coils Refrigerator and freezer both warming up after extended defrost cycles Erratic cooling — temperatures fluctuating unpredictably Replaces Part Numbers This temperature sensor directly replaces the following OEM and cross-reference part numbers: WR55X10025, 914093, WR50X10027, WR50X10034, WR50X10055, WR50X10067, WR55X10025-50PK, WR55X10025B, WR55X10026, WR55X10027, WR55X10028, WR55X10030, WR55X10087, WR55X10088, WR55X10089, WR55X10367, WR55X10380, WR55X10661, WR55X10711, WR55X10735, WR55X10736, WR55X10737, WR55X10937, WR55X10938, WR55X10939, WR55X11121, WR55X11141, WR55X11151, WR55X11152, AH304103, EA304103, OEM9556230, AP3185407, EAP304103, AGE29661, PD00000992, PS304103 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This temperature sensor is compatible with select refrigerators from the following brands: GE refrigerators (side-by-side, French door, top-freezer, and bottom-freezer) Hotpoint refrigerators Haier refrigerators (select GE-platform models) Café refrigerators Monogram refrigerators Note: Some GE refrigerator models use two or more temperature sensors. This part is sold individually. Check your model's parts diagram or contact our support team to confirm how many sensors your model requires before ordering. Key Features Monitors fresh food and freezer compartment temperatures and communicates readings to the main control board Also functions as a defrost sensor on the evaporator coil on applicable models Fits both fresh food and freezer positions White plastic construction — durable and resistant to refrigerator temperature extremes Direct replacement for WR55X10025 and over 30 earlier GE thermistor part numbers Compatible with GE, Hotpoint, Haier, Café, and Monogram refrigerators Sold individually — verify quantity needed for your model before ordering Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in under 30 minutes with basic hand tools Product Specifications Part Number WR55X10025 Part Type Refrigerator Temperature Sensor (Thermistor) Condition Aftermarket Replacement Application Fresh food compartment, freezer compartment, and evaporator coil (defrost sensor) depending on model Sensor Body Length Approximately 1-1/4 inches Color White Material Plastic Includes Sensor with wire leads Sold As Single sensor (some models require 2 — verify before ordering) Compatible Brands GE, Hotpoint, Haier, Café, Monogram Installation Notes ⚠️ Unplug Refrigerator Before Starting Unplug the refrigerator from the power outlet before beginning any repair. To access the fresh food thermistor, locate the sensor on the left wall of the fresh food compartment — it may be clipped into a housing or bracket. Disconnect the wire connector and pull the old sensor out of its bracket. Slide the new WR55X10025 sensor into the bracket and reconnect the wire connector. To access the freezer or evaporator thermistor, remove the freezer shelves and back panel, then locate the sensor clipped to the evaporator coil bracket. Remove any tie wrap securing the sensor, pull the old sensor from the bracket, insert the new sensor, and reconnect the wire connector. Reinstall the back panel and shelves, restore power, and verify the refrigerator returns to the correct set temperature. Tools needed: Phillips screwdriver, flat pry tool (for panel clips), work gloves. Frequently Asked Questions How many temperature sensors does my GE refrigerator have? The number of sensors varies by model. Many GE French door and side-by-side refrigerators use two or three WR55X10025 sensors — one in the fresh food compartment, one in the freezer, and sometimes one on the evaporator coil. Check your model's parts diagram or contact our support team with your model number to confirm how many you need before ordering. What is a thermistor and how does it work? A thermistor is a type of resistor whose electrical resistance changes with temperature. The main control board sends a small voltage through the thermistor and measures the resistance — a higher resistance means a lower temperature, and a lower resistance means a higher temperature. The board uses this reading to decide when to run the compressor and fans to maintain the set temperature. A failed thermistor sends incorrect readings, causing the refrigerator to over-cool, under-cool, or malfunction during defrost cycles. Can a faulty temperature sensor cause the refrigerator to not defrost? Yes. On models where the WR55X10025 also serves as the defrost sensor on the evaporator coil, a faulty sensor can cause the control board to incorrectly time or skip defrost cycles entirely — leading to excessive frost or ice buildup on the evaporator coils. This frost buildup can eventually block airflow and cause both the refrigerator and freezer sections to warm up. How do I know if my temperature sensor is the cause of my cooling problem? The most reliable way to test the thermistor is with a multimeter. Disconnect the sensor and measure its resistance at room temperature — a working WR55X10025 should read approximately 16,000 ohms at 32°F, dropping as temperature increases. An open circuit (infinite resistance) or short circuit (zero resistance) reading confirms the sensor has failed. If resistance is within the normal range but the refrigerator still has issues, the control board or other components may be at fault. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from durable plastic to match the dimensions and performance specifications of the original WR55X10025 temperature sensor. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO DC31-00187A Washer Drain Pump Motor The XPARTCO DC31-00187A is an aftermarket replacement washer drain pump motor compatible with select Samsung front-load and top-load washers in the WA4, WA5, WF2, WF3, WF4, and WF5 series, as well as select Kenmore washers built on the Samsung platform. The drain pump motor drives the impeller that expels water from the washer tub during the drain phase of each wash cycle. When the motor fails, the washer will not drain, will leave standing water in the tub, stop mid-cycle, or display error codes 5C, SE, SC, 5E, or SUDS. This motor-only assembly includes the pump motor, impeller, and replacement O-ring. Rated 120V, 60Hz, 80W, 1.1A (CL.F), with a 30-minute on / 30-minute off duty cycle. Dimensions: 4-1/4"L x 3"W x 4-1/4"H in gray/white/black plastic, metal, and rubber housing. The DC31-00187A is the motor component that installs into the existing pump housing on compatible Samsung washers — the pump housing (DC97-20621C assembly) is reused from the old pump, making this a motor-only swap rather than a complete pump replacement. It directly replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 03DC3100187A, 4958525, AP6977256, EAP9605762, PD00056512, PS9605762, and PS1274262. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DC31-00187A Washer Drain Pump Motor fixes Samsung front-load and top-load washers displaying error codes 5C, SE, SC, 5E, or SUDS, not draining, leaving standing water, or making loud noise during the drain cycle. Motor-only assembly — includes motor, impeller, and O-ring; installs into existing pump housing. 120V/60Hz/80W/1.1A/CL.F. 30 min on/30 min off. 4-1/4"L x 3"W x 4-1/4"H. Replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 4958525, AP6977256, PS9605762. Compatible with Samsung WA4/WA5/WF2/WF3/WF4/WF5 series. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Error codes 5C, SE, SC, 5E, or SUDS displayed — drain fault detected Washer stopping mid-cycle due to a drain fault Loud humming during the drain phase — motor energized but impeller not turning Grinding or rattling during drain — damaged impeller or worn motor bearings Clothes excessively wet after a cycle — pump not fully removing water before spin Water draining very slowly — motor weakening below rated performance Replaces Part Numbers This drain pump motor directly replaces the following OEM and cross-reference part numbers: DC31-00187A, DC31-00178A, DC31-00178D, 03DC3100187A, ASM654116, EAP9605762, 4958525, AP6977256, PD00056512, PS12742622, PX3516-01. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Samsung front-load and top-load washers from the following series: Samsung top-load washers — WA4 series (WA40J3000AW, WA44A3205AW, WA45H7000AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45R6100AC and related models) Samsung top-load washers — WA5 series (WA50F9A6DSW, WA50M7450AW, WA50R5200AW, WA50R5400AV and related models) Samsung front-load washers — WF2 series (select models) Samsung front-load washers — WF3 series (select models) Samsung front-load washers — WF4 series (WF42H5000AW, WF42H5200AW, WF45M5500AW, WF45N5300AW, WF45R6100AC, WF45T6000AW, WF45A6400AV, WF45B6300AP and related models) Samsung front-load washers — WF5 series (select models) Kenmore / Sears washers (select Samsung-built models) Note: The DC31-00187A is the pump motor only — it installs into the existing pump housing (DC97-20621C assembly) which is retained from the old pump. The housing is not replaced. Check and clean the drain filter before replacing the pump motor — a clogged filter is a common cause of drain errors that doesn't require motor replacement. Key Features Pump motor only — includes motor, impeller, and O-ring; installs into the existing DC97-20621C pump housing retained from the old pump Drives the pump impeller to expel water from the washer tub during the drain cycle Resolves Samsung error codes 5C, SE, SC, 5E, and SUDS caused by drain pump motor failure Rated 120V, 60Hz, 80W, 1.1A (CL.F) — correct specifications for compatible Samsung washers Duty cycle: 30 minutes on / 30 minutes off Dimensions: 4-1/4"L x 3"W x 4-1/4"H Replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 4958525, AP6977256, PS9605762, and PS1274262 Compatible with Samsung WA4, WA5, WF2, WF3, WF4, WF5 series and Kenmore Samsung-built washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number XPDC31-00187A Also Covers DC31-00187D, DC31-00178A, DC31-00178D (variants) Part Type Washer Drain Pump Motor (Motor Only — reuses existing housing) Condition Aftermarket Replacement Application Samsung Front-Load and Top-Load Washers (WA4/WA5/WF2/WF3/WF4/WF5) Voltage 120V AC Frequency 60 Hz Wattage 80W Amperage 1.1A Duty Class CL.F Duty Cycle 30 minutes on / 30 minutes off Dimensions 4-1/4"L x 3"W x 4-1/4"H Color Gray / White / Black Material Plastic / Metal / Rubber Includes Pump motor, impeller, O-ring Error Codes Resolved 5C, SE, SC, 5E, SUDS Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves — there are sharp edges inside the washer cabinet. For front-load models: remove the lower front access panel to expose the pump housing and filter. Drain residual water via the filter drain hose (have a shallow pan ready). Disconnect the wire harness from the motor. On most Samsung front-load models, the motor assembly twists out of the pump housing by rotating counter-clockwise — do not force it. Remove the old motor, note the O-ring position, and install the new O-ring from this kit onto the new DC31-00187A motor. Insert the new motor into the housing and twist clockwise to lock. Reconnect the wire harness. Reinstall the lower panel, restore power and water, and run a drain/spin cycle to confirm drainage. For top-load models: access through the lower front panel or by tilting the washer on its side depending on model. Tools needed: Phillips screwdriver, pliers, shallow pan, towels, work gloves. Frequently Asked Questions What is the difference between DC31-00187A and DC97-20621C? The DC31-00187A is the drain pump motor — the electrical component that drives the impeller. The DC97-20621C is the complete drain pump assembly, which includes the motor plus the outer pump housing, hose connection ports, and mounting hardware. When you order the DC31-00187A, you replace only the motor and reuse the existing DC97-20621C pump housing. When you order the DC97-20621C, you replace the entire assembly including the housing. Both resolve the same drain fault — the DC31-00187A is the more targeted repair when the housing is in good condition. What error codes indicate a drain pump motor failure? Error codes 5C, SE, SC, 5E, and SUDS on compatible Samsung washers all indicate a drain fault — the washer was unable to drain within the expected time. Before replacing the motor, clean the drain filter/coin trap at the lower front panel. A clogged filter is one of the most common causes of these error codes and does not require motor replacement. If the filter is clear and the codes persist, or if the pump is making loud noise or is completely silent during the drain phase, the motor needs replacement. What is the difference between DC31-00187A and DC31-00178A? These are cross-references for the same or very similar Samsung drain pump motor used across different Samsung washer generations. The DC31-00178A was used on earlier Samsung models and the DC31-00187A is the current version. Both are commonly listed as interchangeable replacements for each other in Samsung washer drain pump repair. The DC31-00187D and DC31-00178D are also variants of the same motor from different production runs. Should I clean the filter before replacing the pump motor? Yes — always check and clean the drain filter first. On Samsung front-load washers, the filter is accessible behind the lower front kick panel, typically on the right side — remove the cap slowly and drain water into a shallow pan first. Lint, coins, debris, and hair are very common causes of Samsung drain error codes that are completely resolved by cleaning the filter without any parts replacement. If the filter is clear and the error codes persist, the pump motor is the next component to replace. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications and performance of the original DC31-00187A drain pump motor. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

285751 Washer Genuine Agitator Dog Cam Kit Replaces Part Numbers:  285751, 2837, 3351019, 387092, 3947410, AH334624, EA334624, OEM9283568, AP3094521, PS334624. Description: This Agitator Kit is an OEM replacement part for specific Whirlpool top-loading washer models. Installed in the center of the wash basket, it aids in the mechanical agitation central to regular laundry cleaning.It contains the plastic cam and four plastic dogs needed to repair a malfunctioning or noisy agitator during the wash cycle.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

DC64-01570A Washer Genuine Door Boot Rubber boot assembly. Fits select Samsung front-load washer models. Replaces Part Numbers: DC64-01570A, DC97-14560A, DC97-14560K, DC97-14560L,  AP4342244, PS4211426. Description: This Washer Door Diaphragm is an essential component for maintaining your washer's functionality. This Genuine replacement part ensures a secure and effective seal, preventing leaks and enhancing the overall performance of your washing machine. Specifically designed for compatibility with a range of Samsung washer models, it guarantees a perfect fit and straightforward installation. Made from durable materials,  

Read more less

WR55X10025 Genuine OEM GE Refrigerator Temperature Sensor The WR55X10025 is a genuine GE OEM temperature sensor, also called a thermistor, for GE, Hotpoint, and Kenmore refrigerators. This sensor measures air temperature inside the refrigerator or freezer compartment and reports it continuously to the main control board, which uses that reading to regulate the cooling cycle. On some models, this same sensor design also serves as the defrost sensor mounted on the evaporator coil, monitoring temperature there to help manage the defrost cycle. Because the control board relies entirely on this sensor's reading to make cooling decisions, a failing or inaccurate sensor can cause the refrigerator to run too cold, too warm, or run for excessively long periods as it tries to correct a temperature it's misreading. On models where it doubles as a defrost sensor, a failure here can also contribute to frost or ice buildup in the freezer. This is a relatively inexpensive part, and it's commonly the actual cause behind symptoms that get mistakenly blamed on the main control board. It directly replaces AP3185407, 914093, AH304103, EA304103, PS304103, WR50X10027, WR50X10034, WR50X10055, WR50X10067, WR55X10025B, WR55X10026, WR55X10027, WR55X10028, WR55X10030, WR55X10087, WR55X10088, WR55X10089, WR55X10367, WR55X10380, WR55X10661, WR55X10711, WR55X10735, WR55X10736, WR55X10737, WR55X10937, WR55X10938, WR55X10939, WR55X11121, WR55X11141, WR55X11150, WR55X11151, and WR55X11152. Quick Answer The WR55X10025 Genuine OEM GE Refrigerator Temperature Sensor fixes GE, Hotpoint, and Kenmore refrigerators that run too cold, too warm, run for excessively long periods, or (on models where this sensor doubles as a defrost sensor) show frost or ice buildup in the freezer. A healthy sensor reads approximately 5,000 ohms at 77°F. Replaces AP3185407, 914093, AH304103, EA304103, PS304103, and a wide range of WR50X/WR55X-prefix numbers listed below. This is an inexpensive part that's frequently the actual cause behind symptoms mistakenly blamed on the main control board — worth testing or replacing before assuming a costlier board repair is needed. Common Problems This Part Fixes Refrigerator running too cold Refrigerator running too warm Refrigerator running for excessively long periods Freezer not defrosting properly (on models where this sensor also serves as the defrost sensor) Freezer too cold or showing frost buildup Display temperature reading that doesn't match the actual temperature inside the compartment Inconsistent or fluctuating cooling performance Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator temperature sensor directly replaces the following OEM and cross-reference part numbers: WR55X10025, 914093, WR50X10027, WR50X10034, WR50X10055, WR50X10067, WR55X10025-50PK, WR55X10025B, WR55X10026, WR55X10027, WR55X10028, WR55X10030, WR55X10087, WR55X10088, WR55X10089, WR55X10367, WR55X10380, WR55X10661, WR55X10711, WR55X10735, WR55X10736, WR55X10737, WR55X10937, WR55X10938, WR55X10939, WR55X11121, WR55X11141, WR55X11151, WR55X11152, AH304103, EA304103, OEM9556230, AP3185407, EAP304103, AGE29661, PD00000992, PS304103 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This temperature sensor is compatible with select GE, Hotpoint, and Kenmore refrigerators, and is used broadly across most GE side-by-side and French door refrigerator configurations. Note: While this sensor is used across a very broad range of GE refrigerator models, always verify your full model number before ordering, since some models use a different sensor design. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified resistance curve for accurate temperature reporting Measures air temperature and reports it continuously to the main control board Also used as a defrost sensor on the evaporator coil on select models Resolves "too cold," "too warm," "runs too long," and "display reading doesn't match actual temperature" symptoms Direct drop-in replacement — matches the original mounting and wiring Replaces a wide range of WR50X and WR55X-prefix part numbers listed above Compatible with GE, Hotpoint, and Kenmore refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance DIY-friendly repair, typically completed in under an hour Product Specifications Part Number WR55X10025 Part Type Refrigerator Temperature Sensor (Thermistor) Condition Genuine OEM Brand GE Function Measures compartment or evaporator temperature and reports it to the control board Typical Resistance Approx. 5,000 ohms at 77°F Repair Difficulty Easy — typically under 1 hour Quantity 1 temperature sensor Compatible Brands GE, Hotpoint, Kenmore Installation Notes ⚠️ Danger — Authorized Service Part Required For Flammable Refrigerant Systems GE's own service guidance carries an explicit warning for this component: it is a manufacturer-authorized service part intended for use in refrigerator models that use a flammable refrigerant, such as R600a. Using an unauthorized or incorrectly rated service part in a unit that uses a flammable refrigerant could lead to a risk of fire or explosion. Before ordering or installing, confirm your refrigerator's refrigerant type and verify this part is correct for your specific model. If you have any doubt about your refrigerant type or the correct part for your unit, contact our support team with your model number before proceeding, or have a qualified appliance technician perform this repair. ⚠️ Unplug Refrigerator Before Starting — Test With A Multimeter Before Replacing Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. Before replacing, it's worth testing the old sensor with a multimeter set to ohms — a healthy sensor reads approximately 5,000 ohms at 77°F; a reading well outside that range, or an open circuit, confirms a failed sensor. Locate the sensor, typically mounted on an interior wall of the compartment or clipped to the evaporator coil depending on your model. Photograph the wiring and mounting position before disconnecting anything. Disconnect the sensor's wire connector, remove any mounting clip or bracket, and pull the old sensor free. When positioning the new WR55X10025, make sure it sits in open air away from direct contact with ice buildup areas, since ice touching the sensor can cause it to read colder than the compartment's actual temperature. Reconnect the wire connector and secure the mounting clip. Restore power and monitor the refrigerator over the next 24 hours, comparing the display temperature to an independent thermometer placed in the compartment to confirm accuracy. Tools needed: multimeter, work gloves. Frequently Asked Questions How do I test whether this sensor has actually failed? Use a multimeter set to ohms and test the sensor across its two terminals. A healthy sensor typically reads approximately 5,000 ohms at 77°F room temperature; a reading significantly outside that range, or no reading at all (open circuit), confirms the sensor has failed and should be replaced. My display shows a temperature that doesn't match how cold the fridge actually feels. Could positioning be the issue, not the sensor itself? Yes, this is a documented and somewhat subtle failure mode. If the sensor ends up positioned too close to an area where ice or frost accumulates, the ice's surface temperature can pull the sensor's reading colder than the actual compartment air temperature, causing the display to show a colder number than reality — sometimes off by several degrees. One customer traced exactly this issue to ice buildup near the sensor location and resolved it by ensuring the new sensor sat clear of that ice-prone area during installation. Could my problem actually be the control board instead of this sensor? It's worth testing this sensor first before assuming a control board issue. This is a relatively inexpensive part, and it's commonly the actual root cause behind symptoms that get misdiagnosed as a control board failure, since the board is only ever as accurate as the temperature data it receives. Testing or simply replacing this sensor is a low-cost step worth taking before pursuing a more expensive board repair. Why is there a fire/explosion warning on this part? Some refrigerators use a flammable refrigerant, such as R600a (isobutane), instead of older non-flammable refrigerants. Electrical components near refrigerant lines can be a source of ignition if a leak were ever present, which is why GE requires an authorized, correctly rated service part for these systems rather than a generic substitute. Confirming your model and refrigerant type before ordering is the appropriate precaution. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original resistance curve and mounting configuration of the temperature sensor originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less