Search results for "burner receptacle"

8053720 Range Genuine Surface Burner Igniter Replaces: W11032529, 8053720, W10850843, W10896683, 3186479, 3186480, 3186482, 3186486, 4455849, AP6038814, PS11770331. 8053720 Range Surface Burner Igniter – Genuine OEM Replacement Ensure reliable burner ignition on your gas range with the 8053720 Surface Burner Igniter. This Genuine OEM part provides the spark needed to ignite the burner quickly and safely. Key Features: ✅ Replaces: W11032529, 8053720, W10850843, W10896683, 3186479, 3186480, 3186482, 3186486, 4455849, AP6038814, PS11770331. ✅ Compatible with Whirlpool, KitchenAid, Maytag, and more ⚡ Supplies consistent spark to surface burner 🛠️ Durable ceramic construction for long-lasting use 🧰 Easy to install – OEM fit and function ⚠️ Disconnect power and gas before installation. Need help confirming compatibility? Contact us! 📦 Part Number: 8053720

Read more less

XPARTCO 7733P410-60 Surface Burner Knob (Replaces WP7733P410-60) Product Overview The XPARTCO 7733P410-60 Surface Burner Knob (Replaces WP7733P410-60) is designed to control the heat level of your range’s surface burners. This durable replacement knob restores precise control and a clean, finished look to your cooktop. Quick Answer If your stove knob is cracked, loose, missing, or difficult to turn, the 7733P410-60 burner knob is likely worn. Replacing it restores proper control of burner heat settings. Replaces Part Numbers Replaces OEM part number: WP7733P410-60, 7733P410-60, 74007733, WP7733P410-60VP, EAP11744702, AWP48511, PD00004326, AP6011505, PS11744702. Compatibility This surface burner knob is compatible with select Whirlpool, Maytag, Amana, and other compatible ranges. Whirlpool Ranges Maytag Ranges Amana Ranges Always verify your appliance model number before ordering. Common Problems This Part Fixes Broken or cracked knob Knob slipping or not turning properly Missing control knob Difficulty adjusting burner heat Key Features Restores precise burner control Easy push-on installation High-quality aftermarket replacement Durable construction for daily use Product Specifications Part Number: 7733P410-60 Part Type: Surface Burner Knob Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Range Cooktop Control Troubleshooting Guide Knob spins freely → Worn internal insert Cannot adjust flame → Damaged knob Knob falls off → Cracked or loose fit When Should You Replace This Knob? Replace this knob if it is cracked, loose, missing, or no longer controls burner settings accurately. Installation Notes ⚠️ Ensure the appliance is off. Pull the old knob straight off the control shaft and push the new knob firmly into place. Related Parts Surface Burner Valve Igniter Switch Control Panel Overlay Frequently Asked Questions Will this knob fit my range?This knob fits many Whirlpool and compatible models. Always verify your model number. Is installation difficult?No, most knobs are push-on and can be replaced without tools. What are signs of a bad knob?Cracks, slipping, or inability to control heat settings. Is this OEM or aftermarket?This is a high-quality aftermarket replacement part. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support

Read more less

XPARTCO 316489403 Gas Oven Igniter The XPARTCO 316489403 is an aftermarket replacement gas oven igniter compatible with a wide range of Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, and Kenmore gas ranges, ovens, and stoves. The oven igniter is the component that lights the gas burner — when you set the oven to bake or broil, electricity flows through the igniter, heating it until it glows bright orange. This heat both ignites the gas and draws enough current to open the gas safety valve, releasing gas to the burner. When the igniter weakens with age, it may still glow but no longer pull enough current to open the safety valve — so the oven fails to light, takes a long time to heat, or heats unevenly. This is a flat-style, open-cage igniter. Electrical rating: 3.2–3.6 amps, 120V AC. Made of silicon carbide and ceramic for high heat resistance and long service life. Overall dimensions: 3-1/2"L x 1-3/4"W x 13/16"H with a 1.5" ceramic block; the lead and plug measure approximately 16" long. Includes the flat-style igniter assembly with bracket and leads/plug. It directly replaces 316489403, 5304508786, 7316489403, 501RB, 1513415, AH2364063, AP4433236, EA2364063, EAP2364063, PD00000756, and PS2364063. Important: the igniter element is fragile — handle it only by the bracket, never by the element itself. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 316489403 Gas Oven Igniter fixes Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, and Kenmore gas ovens that won't light, take too long to heat, heat unevenly, or where you smell gas because the igniter is too weak to open the safety valve. Flat-style open-cage igniter. 3.2–3.6A, 120V AC. Silicon carbide/ceramic. Overall 3-1/2"L x 1-3/4"W x 13/16"H, 16" lead. Replaces 5304508786, 7316489403, 501RB, 1513415, AH2364063, AP4433236, EA2364063, EAP2364063, PD00000756, PS2364063. Handle by the bracket only — the element is fragile. Common Problems This Part Fixes Oven won't light or heat at all — igniter too weak to open the gas safety valve Oven takes a long time to reach temperature — igniter glowing but drawing insufficient current Oven heats unevenly or undercooks food — weak or slow ignition Igniter glows but the burner never ignites — classic sign of a degraded igniter Igniter doesn't glow at all — burned out or open circuit (no power reaching the burner) Gas smell when the safety valve opens but the burner doesn't light Oven runs erratically or won't maintain temperature Igniter visibly cracked, broken, or with a damaged element Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This gas oven igniter directly replaces the following OEM and cross-reference part numbers: 316489403, 5304508786, 7316489403, Model 501RB, AH2364063, EA2364063, EAP2364063, AFR16172, AP4433236, PD00000756, PS2364063. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: on some models this is the broil (upper) igniter, and the bake (lower) igniter is a different part — see the FAQ below on bake vs broil igniters. Compatibility This gas oven igniter is compatible with select gas ranges, ovens, and stoves from the following brands: Frigidaire gas ranges and ovens — including many Frigidaire Gallery models (LGGF, FGGF, FFGF series and related) Electrolux gas ranges and ovens (select models) Crosley gas ranges and ovens (select models) Gibson gas ranges and ovens (select models) Kelvinator gas ranges and ovens (select models) Tappan gas ranges and ovens (select models) White-Westinghouse gas ranges and ovens (select models) Ikea gas ranges and ovens (select Frigidaire-built models) Kenmore / Sears gas ranges and ovens (select Frigidaire-built models, including 790-series) Note: This igniter fits specific models — always verify against your appliance's model number before ordering. On ranges with two igniters (a bake igniter and a broil igniter), confirm which one you need (see the bake-vs-broil FAQ below). Contact our support team with your model number if you're unsure. Key Features Gas oven igniter — heats up to ignite the burner and draws current to open the gas safety valve Flat-style, open-cage design Resolves "won't light," "slow to heat," "uneven heating," "glows but won't ignite," and "gas smell" symptoms caused by a weak or failed igniter Electrical rating: 3.2–3.6 amps, 120V AC Silicon carbide and ceramic construction — high heat resistance and long service life Overall dimensions: 3-1/2"L x 1-3/4"W x 13/16"H with a 1.5" ceramic block; lead and plug approximately 16" long Includes the flat-style igniter assembly with bracket and leads/plug (some kits include ceramic wire nuts) Replaces 5304508786, 7316489403, 501RB, 1513415, AH2364063, AP4433236, EA2364063, EAP2364063, PD00000756, and PS2364063 Compatible with Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, and Kenmore gas ranges and ovens Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number 316489403 Part Type Gas Oven Igniter (Flat Style, Open Cage) Condition Aftermarket Replacement Application Gas Ranges, Ovens, and Stoves (Frigidaire platform) Amperage 3.2–3.6 Amps Voltage 120V AC Igniter Style Flat, open cage Overall Dimensions 3-1/2"L x 1-3/4"W x 13/16"H Ceramic Block 1.5" L Lead Length Approximately 16" Material Silicon carbide / ceramic / metal Color Almond / White / Gray Includes Igniter assembly with bracket and leads/plug Compatible Brands Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, Kenmore Installation Notes ⚠️ Gas Appliance Safety Warning This part is installed in a gas oven. Shut off the gas supply to the range at the shutoff valve and disconnect electrical power at the breaker before beginning any repair. After installation, if you smell gas at any point, leave the area immediately and contact your gas utility provider. If you're not comfortable working around gas components, have this repair done by a qualified appliance technician. Improper gas appliance repairs can cause fire, explosion, or carbon monoxide hazards. ⚠️ Handle the Igniter by the Bracket Only — The Element Is Fragile Disconnect power at the breaker and shut off the gas supply before beginning. Wear work gloves and safety glasses. The silicon carbide igniter element is extremely fragile and cracks easily — handle the new igniter only by its metal bracket, never by touching the element itself. Skin oils and any impact can shorten its life or break it. Locate the igniter: the bake igniter is beneath the oven floor panel (remove the oven racks, then the floor panel, and on some models the bottom drawer for access), while the broil igniter is mounted near the top of the oven cavity. Photograph the wiring connection before disconnecting. Disconnect the old igniter's wire leads at the connector (they're often joined with ceramic wire nuts). Remove the screws securing the old igniter bracket and lift it out. Install the new 316489403 by securing its bracket in the same position and orientation, then connect the wire leads (use the included or existing ceramic wire nuts — regular wire nuts can't handle the heat). Route the leads away from the burner flame. Restore gas and power. Test by setting the oven to bake (or broil, if that's the igniter you replaced) — the igniter should glow bright orange within a minute or so, and the burner should light within about 60–90 seconds. Tools needed: Nut driver, Phillips screwdriver, work gloves, safety glasses. Frequently Asked Questions My igniter glows but the oven won't light — do I still need to replace it? Yes — this is actually the most common way an oven igniter fails, and it's counterintuitive. The igniter has two jobs: to get hot enough to ignite the gas, AND to draw enough electrical current to open the gas safety valve. As an igniter ages, it can still glow (so it looks like it's working) but weaken to the point where it no longer pulls enough current to open the safety valve — so no gas is released and the burner never lights. If your igniter glows orange but the burner doesn't light within about 90 seconds, the igniter is weak and needs replacement. A good rule of thumb: if it takes more than 90 seconds from glow to flame, the igniter is on its way out. Is the 316489403 the bake igniter or the broil igniter? This is an important distinction, and there's genuine confusion in the industry about it. On many Frigidaire gas ranges, the 316489403 is used as the broil (upper) igniter with an approximately 14–16" lead, while the bake (lower) igniter is a different part — 5304506545 (which superseded 316489404) — often with a shorter lead. However, some sources and parts diagrams list them differently or even reversed, and on some models the 316489403 serves the bake position. The safest approach: look up YOUR specific model number to confirm which igniter you need, and compare your old igniter's lead length to the replacement. If your old igniter's leads reach a connector far from the igniter (14–16"), the 316489403 with its 16" lead is likely correct. Contact our support team with your model number and we'll confirm. Why do I smell gas when I try to use the broiler? If you smell gas when the broiler's safety valve opens but the burner doesn't light, it usually means the igniter isn't getting hot enough (or drawing enough current) to ignite the gas that's being released — so raw gas escapes before shutting off. This points to a weak igniter. To confirm which part is at fault: with the gas off, do a voltage test at the oven safety valve on the broil side — you should read between 3.0 and 3.3 VAC. If the voltage is correct but the burner won't light, the igniter is the problem. If there's no proper voltage, or the burner tube has spider webs or debris blocking it, address those first. Also inspect the gas supply tube from the safety valve to the burner for damage or loose connections. Why do I need to handle the igniter so carefully? The igniter's heating element is made of silicon carbide, a material that's excellent at withstanding heat but is brittle and cracks easily from impact or flexing. Even touching the element with bare fingers can leave oils that create hot spots and shorten its life, and a small bump can crack it invisibly, causing premature failure. Always handle the new igniter by its metal bracket, never by the element or the ceramic block. When installing, be careful not to bump the element against the oven walls or burner. This care is the single biggest factor in whether your new igniter lasts years or fails early. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured from silicon carbide and ceramic to match the electrical specifications (3.2–3.6A, 120V AC), flat open-cage style, dimensions (3-1/2"L x 1-3/4"W x 13/16"H, 16" lead), and ignition function of the original 316489403 gas oven igniter used in compatible Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Ikea, and Kenmore gas ranges and ovens. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10918546CM Gas Oven Igniter Replaces Part Numbers: W10918546, W10140611, 98005652, W10918546VP, WPW10140611, AP6037202, PS11770066. 3.4 - 3.6 Amp, 1.5" block, 3.75" cage, 10" leads w/male pins. Bake igniter for specific single burner Whirlpool range models. Description: This Oven Igniter is a replacement part for select Maytag, Kenmore, Whirlpool gas oven models, responsible for igniting the gas burner that heats the oven. It works by drawing electrical current through the igniter filament, heating it to a high temperature until it glows and ignites the gas to start the cooking process. This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO W10209656 Range Surface Igniter – Compatible with Whirlpool, Maytag, KitchenAid, and Kenmore Gas Ranges Product Description Restore reliable burner ignition with the XPARTCO W10209656 Range Surface Igniter. This high-quality aftermarket replacement provides the heat needed to ignite gas burners on your cooktop. A weak or failed igniter can cause burners not to light or take too long to ignite. Replacing it with this durable XPARTCO igniter restores instant ignition and safe cooking performance. Replaces Part Numbers WPW10209656, W10209656, 1468965, 98008959, 98012193, 98014514, 98014515, 98017561, 98017562, 98017917, W10112313, W10127479, AP6017135, PS11750430. Compatibility This replacement surface igniter is compatible with select Whirlpool, Maytag, KitchenAid, and Kenmore gas ranges. Example compatible models include (but are not limited to): Whirlpool WFG320M0BS3, Maytag MGR6600FZ0, and Kenmore 665.75002100. Always verify your range’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Compatible with Whirlpool-brand gas ranges 🔥 Reliable Ignition – Provides consistent spark for fast burner lighting 💰 Affordable Solution – Quality alternative to OEM parts at lower cost 🛠️ DIY Friendly – Installs easily with basic hand tools 🛡️ Fixes Common Issues – Solves burners not igniting or clicking without flame 📐 Product Specification Part Number: W10209656 Component Type: Gas Range Surface Igniter Material: High-temperature ceramic base and metal electrode Mounting: Direct-fit replacement for surface burner assembly Operating Conditions: Designed for standard household gas ranges Compliance: Built to OEM-equivalent standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the range and shut off the gas supply before starting repairs. Steps: Disconnect power and shut off gas supply. Remove burner grates and top panel to access the igniter. Detach the wire connector and mounting screw from the old igniter. Install the new XPARTCO W10209656 igniter and reconnect wires. Reassemble burner components, restore power and gas, and test ignition. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Enjoy quick, reliable ignition every time — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO XGR403 Gas Oven Round Igniter Replaces WB2X9154, 5304401265, 4342528 The XPARTCO XGR403 is a universal round-style oven igniter for gas ranges from GE, Hotpoint, Kenmore, RCA, Roper, Whirlpool, and Electrolux. This is a silicon carbide (carborundum) igniter, and it does double duty as both the spark source and the safety valve trigger: when the oven or broiler calls for heat, current flows through the igniter and it begins to glow. As it heats up, its electrical resistance drops, which increases the current draw through the circuit — and it's that rising current draw, not the glow itself, that eventually pulls in the gas safety valve and lets gas flow to be ignited by the now white-hot igniter tip. If the igniter can't draw enough current, the valve never opens, even though the igniter is clearly glowing. This is why a weakening round igniter produces such a specific and recognizable symptom: it glows, sometimes for well over a minute, but the oven or broiler never actually lights. GE's own service guidance puts a number on this — if the igniter glows for more than about 90 seconds without opening the valve, it no longer has enough draw to do its job and needs to be replaced. This igniter measures approximately 3-1/2" long, is rated 120V at 2.5–3.0A, and ships as a complete kit with a mounting bracket, ceramic wire nut connectors, and installation instructions. It directly replaces WB2X9154, 5304401265, 4342528, GR403, AR403, SGR403, WB13K10027, WB13K3, WB13K4, WB13K1, AP2014008, PS243425, 300259, 319887, 327617, 330689, 337263, 4336387, 4338008, 8053999, and WB00X6640. Quick Answer The XPARTCO XGR403 Gas Oven Round Igniter fixes GE, Hotpoint, Kenmore, RCA, Roper, Whirlpool, and Electrolux gas ranges where the oven or broiler igniter glows but the burner never lights, or the oven doesn't heat at all. Round-style silicon carbide igniter, 3-1/2" long, 120V, 2.5–3.0A. Complete kit with mounting bracket and ceramic wire nuts. Replaces WB2X9154, 5304401265, 4342528, GR403, AR403, SGR403, WB13K10027, WB13K3, WB13K4, WB13K1, AP2014008, PS243425. Round style only — this igniter will NOT replace a flat-style (hot surface) igniter. Common Problems This Part Fixes Oven or broiler igniter glows but the burner never lights Igniter glows for 90 seconds or longer with no ignition — a strong sign it's too weak to open the gas valve Oven doesn't heat at all despite the igniter appearing to glow normally Gas smell near the igniter without ignition — igniter drawing insufficient current to trip the valve Igniter that used to glow bright orange now glows dim or dull Visible cracks, chips, or a broken tip on the ceramic-bodied igniter Intermittent ignition — sometimes lights, sometimes doesn't Igniter that doesn't glow at all — may indicate the igniter or its wiring has failed completely Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This gas oven round igniter directly replaces the following OEM and cross-reference part numbers: 5304401265, 08007988, 235030, 5308007988, 638543, 7954, 8007988, 9360, A00P235030, A00P235230, A1505523, A1505786, AH470557, AP00235030, AP235027, AP235030, DAP235030, EA470557, P235030, AP2592228, PS470557, Q000198333, WB2X9154, 1990, 300259, 319887, 327617, 330689, 337263, 4336387, 4338008, AH243425, EA243425, AP2014008, PS243425, WB00X6640, WB02X9154, WB13K0001, WB13K0003, WB13K0004, WB13K01, WB13K04, WB13K1, WB13K10027, WB13K3, WB13K4, 4342528,  300259, 3196447, 321342, 327617, 337263, 337389, 337390, 3422, 4157446, 4322910, 4332948, 4338008, 4338037, 4342528VP, 4389493, 8053999, AH360921, EA360921, F16-569, GR403, K16866, PS360921, AP3104565, SGR403. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This round-style igniter is a universal replacement compatible with select gas ranges, ovens, and broilers from the following brands: GE and Hotpoint gas ranges (select models using a round XL44-style igniter) Kenmore and RCA gas ranges (select GE-built models) Roper gas ranges (select models) Whirlpool gas ranges (select models) Electrolux gas ranges (select models) Note — round style only, and it may be a bake OR broil igniter: This is a round-style igniter and will NOT replace a flat-style (hot surface) igniter used on other gas range platforms — the two are not interchangeable. Additionally, many gas ranges use a round igniter for both the bake and broil burners; some models use different igniters for each, so confirm whether the failing igniter is for the bake or broil compartment before ordering. Always verify your full model number and igniter style before ordering. Contact our support team with your model number if you're unsure. Key Features Universal aftermarket replacement round-style oven igniter — fits a wide range of GE, Hotpoint, Kenmore, RCA, Roper, Whirlpool, and Electrolux gas ranges Silicon carbide (carborundum) construction glows and draws current to trigger the gas safety valve Resolves "igniter glows but won't light," "oven not heating," and "intermittent ignition" symptoms caused by a weakening igniter Approximately 3-1/2" long, rated 120V at 2.5–3.0A Complete kit — includes mounting bracket, ceramic wire nut connectors, and installation instructions UL listed for safety compliance Replaces WB2X9154, 5304401265, 4342528, GR403, AR403, SGR403, WB13K10027, WB13K3, WB13K4, WB13K1, AP2014008, PS243425, 300259, 319887, 327617, 330689, 337263, 4336387, 4338008, 8053999, and WB00X6640 Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XGR403 OEM Part Number WB2X9154 Part Type Gas Oven Round Igniter (Bake / Broil) Condition Aftermarket Replacement Style Round (not compatible with flat-style igniters) Material Silicon carbide (carborundum) Length Approx. 3-1/2 in. Voltage 120V Amperage 2.5–3.0 A Kit Contents Igniter, mounting bracket, ceramic wire nuts, instructions Certification UL listed Quantity 1 igniter Compatible Brands GE, Hotpoint, Kenmore, RCA, Roper, Whirlpool, Electrolux Installation Notes ⚠️ Danger — Gas Appliance Turn off the gas supply to the range at the shutoff valve and unplug the range (or shut off its circuit breaker) before beginning. After reassembly, check every disturbed gas connection for leaks using a soapy water solution — bubbling indicates a leak. If you ever smell gas at any point during this repair, do not attempt to light the range or operate any switches; leave the area immediately and contact your gas utility or a qualified technician. ⚠️ Fragile — Handle By The Bracket Only Wear work gloves. Remove the oven racks and, if replacing the broil igniter, the broiler pan and floor panel as needed to access the igniter assembly, typically located at the front of the burner tube. Photograph the wiring connections before disconnecting anything. This igniter is extremely fragile — the ceramic body and silicon carbide tip can crack from a light bump or from skin oils weakening the material over time, so handle it only by the metal mounting bracket, never by the ceramic body itself. Disconnect the wire leads at the ceramic wire nut splices (or the terminal connector, depending on your model), then remove the mounting screw and lift the old igniter free. Position the new XGR403 in the same location and orientation relative to the burner tube — proper alignment matters, since the igniter needs to sit close enough to reliably ignite the gas once the valve opens. Secure the mounting bracket, then reconnect the wire leads using the included ceramic wire nuts, twisting them securely and confirming no bare wire is exposed. Restore the gas supply and power, then test the burner and check for leaks at any connection you touched. Watch the igniter glow through a full ignition cycle to confirm the burner lights well within 90 seconds. Tools needed: Phillips or flat-blade screwdriver (model-dependent), soapy water for leak testing, work gloves. Frequently Asked Questions My igniter glows bright orange but the oven never lights. Is this the right part? Yes, this is the single most common symptom of a failing round igniter. As the igniter ages, its silicon carbide element degrades and can no longer draw enough current to trip open the gas safety valve, even though it still glows. A well-known rule of thumb: if the igniter is glowing for more than about 90 seconds without the burner lighting, it has lost the current draw needed to do its job, and replacement is the correct fix. Can I use this for both the bake and broil igniter? On many GE-platform ranges, yes — the same round igniter design serves both the bake and broil burner positions. However, some model platforms use different igniters for bake versus broil, so before ordering, confirm which compartment's igniter has failed and verify your specific model number to make sure this is the correct igniter for that position. Will this fit my flat-style igniter oven? No. This is a round-style (carborundum rod) igniter and is not interchangeable with a flat-style (hot surface) igniter used on other gas range platforms — the mounting, shape, and electrical characteristics are different. Check the shape of your original igniter before ordering: a round igniter looks like a short ceramic rod or cylinder, while a flat igniter has a thin, flat ceramic element. The igniter doesn't glow at all. Is it definitely the igniter itself? Not necessarily. A round igniter that doesn't glow at all can also point to a wiring problem, a failed connection at the ceramic wire nut splice, or in some cases a bad oven control board sending no signal to the igniter circuit. Check that the wiring is intact and securely connected before assuming the igniter itself has failed completely — a partial glow that just won't sustain, versus zero glow whatsoever, can point you toward different causes. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine brand-specific OEM part, but is manufactured to match the round silicon carbide design, 120V/2.5–3.0A electrical rating, and mounting configuration of the OEM igniters (including WB2X9154) used in compatible GE, Hotpoint, Kenmore, RCA, Roper, Whirlpool, and Electrolux gas ranges. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11047722 Genuine OEM Range Radiant Surface Element - Compatible with Whirlpool, KitchenAid, Maytag Product Description Restore your range’s cooking performance with the W11047722 Genuine OEM Range Radiant Surface Element. This Whirlpool-manufactured element is designed for select Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, and other compatible ranges. It provides even heat distribution for reliable cooking, addressing issues like uneven heating, no heat, or burnt-out elements. This single element is rated at 2500W and 240V, ensuring efficient operation for large to medium cookware. Note: Includes (1) radiant surface element. Disconnect power before installation. Verify compatibility with your range model. Replaces part numbers: W11047722, WP8273992, W10248262, 8273992, AP6041999, PS11775308, 316135401, 316224200, 316224201, 318198835, PD00044547, EAP11775308, FIX11775308, AH2361362, EA2361362, AP4416812, PS2361362.  Compatibility: Compatible with select range models, including but not limited to: Whirlpool: WFE525S0HV0, WFE525S0HZ0, WFE525S0JB0, WFE525S0JS0, WFE525S0JW0 KitchenAid: KSEG700EBS0, KSEG700ESS0, KSEG700EWH0 Maytag: MER6600FB0, MER6600FW0, MER6600FZ0 Jenn-Air: JEC3430BB00, JEC3430BS00 Amana: AER6603SFB0, AER6603SFS0, AER6603SFW0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, KitchenAid, Maytag, Jenn-Air, and Amana ranges. 🔧 Specifications: 2500W, 240V, 9 3/4-inch radiant element, glass-ceramic construction. 💪 Reliable Performance: Delivers consistent heat for efficient cooking. 🛠️ Easy Installation: Requires screwdriver and gloves; typically installed in 15–30 minutes. 🛡️ Effective Fixes: Resolves uneven heating, no heat, or burnt-out element issues. Product Specification Part Number: W11047722 Component Type: Radiant surface element Material: Glass-ceramic with metal heating coil Dimensions: Approximately 9 3/4" diameter Electrical Specs: 2500W, 240V Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the range from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your range cooking efficiently today! Add to cart now for a reliable fix!

Read more less

XPARTCO MEE61841401 Gas Oven Igniter The XPARTCO MEE61841401 is an aftermarket replacement oven burner igniter compatible with select LG and Kenmore gas ranges in the LDG, LRG, LSG, LSS, LTG, and LSR series. The igniter is a flat glow bar hot surface igniter made from silicon carbide that draws electrical current through the oven safety valve to open it, then heats to ignition temperature to light the gas burner. When the igniter weakens or fails, the oven will not heat, will take too long to preheat, or the igniter will glow without ever lighting the burner. This igniter draws 3.3–3.8 amps at 120V AC and reaches operating temperatures of 1,800°F–3,100°F within approximately 60 seconds. The igniter body measures 3-1/2 inches long x 1-3/4 inches wide x 7/8 inches high, with a lead/plug assembly extending approximately 10-3/4 inches from the igniter. It includes a 2-wire harness/plug, mounting bracket, and 2 porcelain wire connectors to accommodate direct plug-in or spliced installation. Directly replaces OEM part numbers MEE61841401, MEE61841403, and MEE63084901. Quick Answer The XPARTCO MEE61841401 Gas Oven Igniter fixes LG and Kenmore gas ovens that won't heat, take too long to preheat, display error codes F9 or F11, or have an igniter that glows but never lights the burner. Flat glow bar style, silicon carbide. Draws 3.3–3.8A at 120V. Igniter body 3-1/2" L x 1-3/4" W x 7/8" H with 10-3/4" lead. Includes bracket and 2 porcelain wire connectors. Replaces MEE61841403 and MEE63084901. Common Problems This Part Fixes Oven not heating at all — gas is not igniting Oven takes excessively long to preheat Igniter glows orange or red but never lights the gas burner Error codes F9 or F11 displayed on LG gas ranges Gas smell when oven is turned on but burner does not light Oven heats inconsistently or shuts off mid-cycle Igniter burned out or visibly cracked or broken Replaces Part Numbers This oven igniter directly replaces the following OEM and cross-reference part numbers: MEE61841401, MEE63084901, 1599783, MEE61841403, EAP3535362, ALG1385007, PD00001851, 095225468650, AH3535362, EA3535362, AP5214765, PS3535362. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This igniter is compatible with select gas ranges from the following brands and series: LG gas ranges — LRG series (freestanding) LG gas ranges — LDG series (freestanding) LG gas ranges — LSG series (slide-in) LG gas ranges — LSS series LG gas ranges — LTG series LG gas ranges — LSR series Kenmore / Sears gas ranges (select LG-built models) Compatible with both single and double oven models. Always verify your model number before ordering. Contact our support team if you're unsure. Key Features Flat glow bar hot surface igniter — draws current through the oven safety valve to open it, then ignites the gas burner Silicon carbide construction — superior heat resistance, high melting point, corrosion and oxidation resistant Draws 3.3–3.8 amps at 120V AC — correct amperage range to open the LG gas safety valve Operating temperature: 1,800°F – 3,100°F with approximately 60-second heat-up time Igniter body: 3-1/2" L x 1-3/4" W x 7/8" H; lead/plug assembly: approximately 10-3/4" from igniter body Plug-in installation — includes 2-wire harness/plug, mounting bracket, and 2 porcelain wire connectors for splicing if needed Compatible with single and double oven models Directly replaces MEE61841401, MEE61841403, and MEE63084901 — no modification required in most cases Resolves error codes F9 and F11 on compatible LG gas ranges Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 10–20 minutes with basic hand tools Product Specifications Part Number MEE61841401 Also Replaces MEE61841403, MEE63084901 Part Type Gas Oven Burner Igniter (Flat Glow Bar Hot Surface Igniter) Condition Aftermarket Replacement Application Gas Ranges and Ovens (single and double oven) Igniter Style Flat glow bar, cageless Material Silicon Carbide / Metal / Ceramic / Porcelain / Plastic Colors White / Black / Gray Amperage Draw 3.3 – 3.8 Amps Voltage 120V AC Operating Temperature 1,800°F – 3,100°F Heat-Up Time Approximately 60 seconds Igniter Body Dimensions 3-1/2" L x 1-3/4" W x 7/8" H Lead / Plug Length Approximately 10-3/4 inches from igniter body Includes Igniter, mounting bracket, 2-wire harness/plug, 2 porcelain wire connectors Error Codes Resolved F9, F11 Compatible Brands LG, Kenmore Installation Notes ⚠️ Gas Appliance Safety Warning This part is used in gas ranges. Working with gas appliances carries risk of gas leaks, fire, and explosion if installed incorrectly. Always shut off the gas supply at the shutoff valve and unplug the range before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. If you are not confident working on gas appliances, have this part installed by a qualified appliance technician. ⚠️ Handle With Care — Fragile Igniter Element The silicon carbide igniter element is extremely fragile and sensitive to contamination. Do not touch the ceramic bar with bare hands under any circumstances — oils from skin will damage the element and significantly shorten its lifespan. Handle only by the bracket, wires, and plug. To install: unplug the range and shut off the gas. Remove the oven racks and oven bottom panel. Disconnect the old igniter's wire connector. Secure the new MEE61841401 igniter to the burner bracket with the mounting screws. If the plug is a direct match to your range's harness, plug it in. If not, cut the wires and use the included porcelain wire connectors to splice the new igniter to the existing wiring. Reinstall the oven bottom panel, restore gas supply and power, and run a test cycle. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions What is the difference between MEE61841401, MEE61841403, and MEE63084901? These are all part numbers for the same LG flat glow bar oven igniter used across different model ranges and production runs. MEE63084901 is the earlier part number; MEE61841401 and MEE61841403 are updated versions. All three are interchangeable, and this aftermarket replacement is compatible with all of them. How do I know if my oven igniter needs to be replaced? The most common signs are the oven not heating at all, taking much longer than normal to preheat, or the igniter glowing orange but never lighting the gas burner. A healthy igniter glows bright orange and ignites the burner within about 60 seconds. If it glows dimly or stays on indefinitely without the burner lighting, the igniter has weakened and is no longer drawing enough current to open the gas safety valve. Error codes F9 or F11 on LG ranges can also indicate a failed igniter. Do I need to splice the wires or does it plug straight in? This igniter includes a 2-wire harness/plug for direct plug-in installation on most compatible LG models. If the connector does not match your range's existing harness, cut the old connector off and use the 2 porcelain wire connectors included in the kit to splice the new igniter to the existing wiring. Do not use standard plastic wire nuts — only porcelain connectors should be used near the oven burner due to the high heat involved. What do error codes F9 and F11 mean on an LG range? On compatible LG gas ranges, error code F9 typically indicates an oven heating failure, and F11 can indicate a shorted or failed igniter circuit. Both codes can be triggered by a weak or failed oven igniter. Replacing the MEE61841401 igniter resolves these error codes in many cases — though other causes such as a failed gas safety valve or control board issue should also be ruled out if the problem persists after replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from silicon carbide, metal, ceramic, and porcelain to match the electrical specifications and physical dimensions of the original MEE61841401 igniter. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO DG44-01002A Surface Element Infinite Switch The XPARTCO DG44-01002A is an aftermarket replacement dual element infinite switch (energy regulator) for Samsung electric ranges. This switch does two jobs at once: it regulates how much electrical current reaches its surface element, which is what lets you dial in a precise heat level rather than just on/off, and it also controls the "hot surface" indicator light associated with that burner, letting you know when the element is still hot after use. Over time, the internal contacts in this switch can wear, stick, or fail electrically. Because a single switch controls both functions, a failing switch can produce two very different-looking symptoms depending on which function is affected: the burner may stay stuck on high heat regardless of the dial setting, fail to produce any heat at all, or the hot surface indicator light may stay on for hours after the surface has completely cooled, even though the element itself tests fine. It directly replaces 2087510, MDSA-W21-SKM, MDSA-W888-UNM, MDSA-W888-UM, AP4337066, PS4240803, and EAP4240803. Quick Answer The XPARTCO DG44-01002A Surface Element Infinite Switch fixes Samsung electric ranges where a burner is stuck on high heat regardless of the dial setting, won't produce any heat at all, or the hot surface indicator light stays on for hours after the surface has cooled. Dual element design. Replaces 2087510, MDSA-W21-SKM, MDSA-W888-UNM, MDSA-W888-UM, AP4337066, PS4240803, EAP4240803. This switch controls both the element and its indicator light — if your indicator light won't turn off even though the burner is cool, this switch (not the element) is the cause. Common Problems This Part Fixes Burner stuck on high heat regardless of the dial setting Burner won't produce any heat at all Hot surface indicator light stays on for hours after the burner has completely cooled Inconsistent heating — burner doesn't hold the selected temperature level Unresponsive burner controls Burner that heats erratically rather than at a steady, selected level Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This range surface element infinite switch directly replaces the following OEM and cross-reference part numbers: DG44-01002A, 2087510, , MDSA-W21-SKM, PS4240803, AP4337066, EAP4240803, ASM37999, PD00006793, 737534552513 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This infinite switch is compatible with select Samsung electric ranges in the FCQ3, FE71, FER3, FTQ3, and NE59 series, including model numbers such as NE59J3420 and NE59J4310. Note: This is the switch, not the radiant heating element itself — the companion element is a separate part, DG47-00022A. If you're diagnosing a burner problem, it's worth testing both parts, since either one failing can cause similar symptoms. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement dual element infinite switch (energy regulator) Controls both the surface element's heat output and its hot surface indicator light Resolves "stuck on high heat," "won't heat at all," and "indicator light stays on" symptoms caused by switch failure Direct drop-in replacement — matches the original mounting and wire connections Replaces 2087510, MDSA-W21-SKM, MDSA-W888-UNM, MDSA-W888-UM, AP4337066, PS4240803, and EAP4240803 Compatible with Samsung electric ranges in the FCQ3, FE71, FER3, FTQ3, and NE59 series Aftermarket replacement built to OEM-equivalent quality standards Straightforward DIY repair, typically 10 to 15 minutes Product Specifications Part Number XPDG44-01002A OEM Part Number DG44-01002A Part Type Range Surface Element Infinite Switch (Energy Regulator) Condition Aftermarket Replacement Brand Samsung Design Dual element Function Regulates surface element heat output; controls hot surface indicator light Related Part DG47-00022A radiant element (sold separately) Repair Difficulty Easy — 10 to 15 minutes Quantity 1 infinite switch Compatible Brand Samsung Installation Notes ⚠️ Unplug Range Before Starting — Photograph Wiring Before Disconnecting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically from the rear of the control panel or the underside of the cooktop, depending on your model. Photograph the wiring connections on the old switch before disconnecting anything, since correct wire placement is essential for the switch to control the right burner and indicator light. Remove the screws securing the old switch, gently pry it out, and mark or note each wire's position for reference. Disconnect the wires from the old switch and remove it fully. Install the new DG44-01002A in the same position, reconnect each wire to its original terminal exactly as photographed, and secure the mounting screws. Restore power and test the burner across its full range of settings, confirming both the heat output and the indicator light behave correctly. Tools needed: screwdriver, pliers, pen or pencil for marking wires, work gloves. Frequently Asked Questions My hot surface light stays on for hours even though the burner has cooled down. Is this the switch? Yes. This is a documented symptom specific to this switch, since it controls both the surface element and its indicator light together. If the light isn't going out even though the surface itself is cool to the touch, the switch — not the element — is the correct part to replace. My burner is stuck on high heat no matter what setting I choose. Is that the switch or the element? It could be either, so it's worth testing both with a multimeter before replacing. Test the radiant element first — it should read between 0 and 120 ohms if it's working correctly. Then test the infinite switch itself: remove it, connect a multimeter probe to each prong, and turn the switch to an on position. No continuity indicates the switch is the issue. Several customers have confirmed this exact symptom by swapping switches between two burners and watching the problem follow the switch, which is also a reliable way to isolate the cause if you have two dual-element burners. Should I replace the element (DG47-00022A) at the same time? Not necessarily, but it's worth testing both parts if you're not sure which one has failed, since a bad element and a bad switch can produce overlapping symptoms. If your multimeter tests confirm only the switch has failed, replacing just this part is sufficient. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the dual-element switching function, wire terminal configuration, and mounting design of the original DG44-01002A infinite switch used in compatible Samsung electric ranges. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WB31X5011CM 8" Burner Drip Pan Chrome drip bowl (also called a drip pan) for 8 inch burner on an electric range. The drip pan sits underneath the heating element to collect drips or spills around the burner. 8" Chrome pan/ring. Fits GE, Hotpoint range. Replaces Part Numbers: WB31X5011, 340748, DP102, KIT10, KIT18, KIT2, PM32X0102, PM32X102, WB31X5011A, WB31X5011B, WB31X5011R, AH244470, EA244470, AP2028083, PS244470.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

(2 Pack) WB31X5011CM 8" Burner Drip Pan Chrome drip bowl (also called a drip pan) for 8 inch burner on an electric range. The drip pan sits underneath the heating element to collect drips or spills around the burner. 8" Chrome pan/ring. Fits GE, Hotpoint range. Replaces Part Numbers: WB31X5011, 340748, DP102, KIT10, KIT18, KIT2, PM32X0102, PM32X102, WB31X5011A, WB31X5011B, WB31X5011R, AH244470, EA244470, AP2028083, PS244470.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WB31M19CM 8" Porcelain Drip Pan Porcelain drip bowl (also called a drip pan) for 8 inch burner on an electric range. The drip pan sits underneath the heating element to collect drips or spills around the burner. 8" Porcelain pan. Fits GE, Hotpoint range. Replaces Part Numbers: WB31M19, WB32X5069, WB31M0019, AH244373, EA244373, AP2028043, PS244373.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less