XPARTCO XP6974 Dryer Thermostat Kit Replaces WP3387134, WP3392519, W10900067, 279816
The XPARTCO XP6974 is an aftermarket dryer thermostat kit containing four thermal components for Whirlpool-family electric and gas dryers including Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef. The kit includes the cycling thermostat (WP3387134), thermal fuse (WP3392519), high-limit thermostat and thermal cut-off kit (279816 / W10900067) — the complete set of heat-sensing and safety components that regulate dryer temperature and prevent dangerous overheating.
These four components work together to control and protect the dryer's heating system. When any one of them fails, the dryer may produce no heat, overheat, run too long, or stop mid-cycle. Because a failed thermal fuse is almost always caused by an underlying overheating condition that also stresses the other components, replacing all four together in a single repair is the recommended approach. Includes all wiring hardware needed for installation. Installs in 20–30 minutes with basic hand tools.
Quick Answer
The XPARTCO XP6974 Dryer Thermostat Kit fixes Whirlpool-family dryers that produce no heat, overheat, take too long to dry, or stop mid-cycle. Includes all four thermal components: cycling thermostat (L155-25), thermal fuse (196°F), high-limit thermostat (L250-80), and thermal cut-off (309°F). Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef electric and gas dryers.
Common Problems This Kit Fixes
Dryer produces no heat — thermal fuse or high-limit thermostat has blown
Dryer takes multiple cycles or very long time to dry clothes
Dryer overheats — clothes or drum too hot to touch after a cycle
Dryer shuts off mid-cycle and will not restart
Dryer tumbles normally but generates no heat at all
Dryer runs too long because cycling thermostat is not regulating temperature
Repeated thermal fuse failures — underlying thermostat fault causing recurring overheating
What's in the Kit
Part 1 of 4
WP3387134 Cycling Thermostat
Rated L155-25 · Monitors drum air temperature and cycles the heating element on and off to maintain the set drying temperature · Located on the exhaust duct or blower housing · Should show closed continuity at room temperature
Part 2 of 4
WP3392519 Thermal Fuse
Opens at 196°F (91°C) · One-time safety device located on the exhaust duct · Permanently interrupts power to the heating element if the dryer overheats · Cannot be reset — must be replaced if blown · Most common cause of no-heat in Whirlpool-family dryers
Part 3 of 4
High-Limit Thermostat (279816 / W10900067)
Rated L250-80 · Mounted on the heating element housing · Opens at approximately 250°F to cut power to the heating element if temperature exceeds safe limits · Resets automatically when it cools · Should show closed continuity at room temperature
Part 4 of 4
Thermal Cut-Off Fuse (3977393 / 279816 kit)
Opens at 309°F · Backup one-time safety device on the heating element housing · Permanently interrupts power to the heating element if the high-limit thermostat fails to open · Cannot be reset — must be replaced if blown
Replaces Part Numbers
WP3387134 Cycling Thermostat cross-references:
WP3387134, WP3387134VP, 3387134, 3387135, 3387139, 306910, 3-6910, ET187, AP6008270, PS11741405
WP3392519 Thermal Fuse cross-references:
WP3392519, WP3392519VP, 3392519, 3388651, 694511, 80005, ET401, G4AP0500, AP6008325, PS11741460
279816 High-Limit Thermostat and Thermal Cut-Off Kit cross-references:
279816, 279816VP, W10900067, 3977393, 3977767, WP3977767, WP3977767VP, 3399848, 3399693, 2651, AP3094244, AH334299, EA334299, EAP334299, PS334299
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This thermostat kit is compatible with select gas and electric dryers from the following brands:
Whirlpool dryers (gas and electric)
Kenmore / Sears dryers (Whirlpool-built models)
Maytag dryers (gas and electric)
Amana dryers
KitchenAid dryers
Roper dryers
Admiral dryers
Estate dryers
Crosley dryers
Inglis dryers
Magic Chef dryers
Important: If your thermal fuse has blown, always check for the root cause before replacing — a clogged exhaust vent is the most common cause of dryer overheating. Clean the full length of the exhaust duct before or after this repair. If the vent is clear, a failed cycling thermostat or high-limit thermostat is likely the root cause.
Key Features
Complete 4-part thermal kit — covers the cycling thermostat, thermal fuse, high-limit thermostat, and thermal cut-off in a single repair
Cycling thermostat (L155-25) — regulates drum temperature to maintain consistent, efficient drying
Thermal fuse (196°F) — one-time safety device that permanently interrupts heat if the dryer overheats
High-limit thermostat (L250-80, ~250°F) — cuts power to the heating element when temperature exceeds safe limits; auto-resets
Thermal cut-off (309°F) — backup one-time safety device protecting against heating element runaway
Replacing all four parts together ensures the complete thermal circuit is renewed — prevents recurrence if a failing thermostat caused the fuse to blow
Includes all wiring hardware for installation
Compatible with 11 major appliance brands on the Whirlpool platform
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 20–30 minutes with basic hand tools
Product Specifications
Kit Part Number
XP6974
Condition
Aftermarket Replacement
Application
Gas and Electric Dryers
Kit Includes
1x WP3387134 Cycling Thermostat, 1x WP3392519 Thermal Fuse, 1x High-Limit Thermostat (L250-80), 1x Thermal Cut-Off Fuse (309°F), wiring hardware
Cycling Thermostat Rating
L155-25 (closes at 155°F, opens at 25°F differential)
Thermal Fuse Trip Temp
196°F (91°C) — one-time, non-resettable
High-Limit Thermostat Rating
L250-80 (opens at ~250°F) — auto-resets
Thermal Cut-Off Trip Temp
309°F — one-time, non-resettable
Compatible Brands
Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef
Installation Notes
⚠️ Unplug Dryer and Shut Off Gas Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the back panel of the dryer to access the heating element housing and exhaust duct. The thermal fuse (WP3392519) and cycling thermostat (WP3387134) are located on the exhaust duct or blower housing — disconnect the wires, unscrew the mounting screws, and install the new parts in the same positions. The high-limit thermostat and thermal cut-off (279816 kit) are located on the heating element housing — disconnect the wires and unscrew the mounting screws to remove the old parts and install the new ones. Reconnect all wires to the correct terminals — take a photo before disconnecting to reference during reinstallation. Reassemble the back panel, restore power, and run a test cycle to verify heat. Tip: Before running the dryer, also clean the full length of the exhaust duct — a clogged vent is the most common root cause of dryer overheating and repeated thermal fuse failures. Tools needed: Phillips screwdriver, 1/4" nut driver, needle-nose pliers.
Frequently Asked Questions
What does each part in this kit do?
The cycling thermostat (WP3387134) monitors the air temperature in the exhaust duct and cycles the heating element on and off to maintain the correct drying temperature — it is the part that controls how hot the dryer gets during normal operation. The thermal fuse (WP3392519) is a one-time safety device that permanently cuts power to the heating element if the dryer overheats above 196°F — it is the most common cause of no-heat in Whirlpool-family dryers. The high-limit thermostat opens at approximately 250°F to cut heating element power if temperature gets too high, and resets automatically when it cools. The thermal cut-off is a backup one-time fuse on the heating element that opens at 309°F if the high-limit thermostat fails to protect the heater.
Why should I replace all four parts instead of just the one that failed?
When a thermal fuse blows, it almost always blew because the dryer overheated — and that overheating event put significant stress on all the other thermal components as well. A failing cycling thermostat is the most common cause of repeated thermal fuse failures: if the cycling thermostat stops regulating temperature correctly, the dryer runs too hot, the high-limit thermostat is repeatedly stressed, and the thermal fuse eventually blows. Replacing just the fuse without replacing the cycling thermostat means the same overheating will blow the new fuse. Replacing all four parts at once eliminates that risk in a single repair.
How do I test these parts with a multimeter?
Set the multimeter to continuity or resistance mode. The thermal fuse (WP3392519), cycling thermostat (WP3387134), and high-limit thermostat should all show closed continuity (near-zero resistance) at room temperature. The thermal cut-off should also show closed continuity at room temperature. Any part that reads open (no continuity / infinite resistance) at room temperature has failed and needs to be replaced. A blown thermal fuse or cut-off will always read open — they are one-time devices and cannot reset.
What causes the thermal fuse to blow repeatedly?
The most common cause by far is a clogged exhaust vent — lint accumulation inside the dryer duct restricts airflow, causing heat to build up inside the dryer cabinet until the thermal fuse trips. Always clean the full length of the exhaust duct before and after replacing these parts. Other causes include a failing cycling thermostat that is not regulating temperature correctly, a stuck heating element relay, or a dryer placed in an enclosed space without adequate ventilation.
Is this kit compatible with both electric and gas dryers?
Yes — the XP6974 kit is compatible with both electric and gas Whirlpool-family dryers. Both types use the same cycling thermostat (WP3387134) and thermal fuse (WP3392519). The high-limit thermostat and thermal cut-off (279816 kit) are located on the heating element in electric models and on the burner assembly area in gas models. Always verify your specific model number before ordering to confirm all four parts apply to your dryer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO WE4M137 Dryer High Limit Thermostat
The XPARTCO WE4M137 is an aftermarket replacement high limit thermostat for GE, Hotpoint, and Kenmore dryers. Mounted on the upper right side of the heater housing, this safety thermostat monitors the temperature of the heating circuit and cuts power to the heating element (and in some conditions the motor) if the dryer runs hotter than it should — typically from restricted airflow, a clogged vent, or a failing cycling thermostat. Unlike a one-time thermal fuse, this is an auto-resetting high limit thermostat (rated L315-65F): it opens at approximately 315°F to stop overheating, then automatically closes again once the unit cools down, without needing to be replaced after each trip.
This is a direct-fit aftermarket replacement built to the same temperature rating and mounting as the original thermostat. If this component trips repeatedly, it's worth checking the underlying cause of the overheating at the same time — a clogged lint trap or restricted exhaust vent is the most common root cause.
Quick Answer
The XPARTCO WE4M137 High Limit Thermostat fixes a GE, Hotpoint, or Kenmore dryer that shuts off a few minutes into a heat cycle, stops early and won't restart until it cools down, or cycles on and off intermittently. Auto-resetting, rated to open at approximately 315°F. Classic symptom: dryer runs fine for a few minutes then quits on heat, and won't restart again until it's had time to cool.
Common Problems This Part Fixes
Dryer shuts off a few minutes into a heat-dry cycle
Dryer stops early and won't restart until it cools down
Intermittent shutdowns during the drying cycle
Clothes coming out damp because the cycle keeps cutting short
Dryer won't start at all if the thermostat has failed in an open position
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This thermostat directly replaces the following part numbers:
WE4M137, WE4M457, 276438, WE04M0137, WE04X25197, 559C131G04, AGE25626, AH267900, AP2042565, EAP267900, EA267900, PD00001228, PS267900
These numbers span several generations of GE's own part numbering for this thermostat as model lines and sub-assemblies were updated — all are the correct replacement for this component regardless of which number appears on your dryer's parts diagram.
Compatibility
This thermostat is compatible with 28+ GE, Hotpoint, and Kenmore dryer models, including:
Kenmore 2661532110, GE 2661532210
Numerous additional GE, Hotpoint, and Kenmore dryer and washer-dryer combo models
Note: This thermostat has also been referenced for some Fisher & Paykel dryer applications in sourcing, though we were not able to confirm a specific Fisher & Paykel model list. Confirm your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering.
Key Features
Direct-fit aftermarket high limit thermostat for GE-built dryers
Auto-resetting design — no need to replace after each trip, unlike a one-time thermal fuse
Rated to open at approximately 315°F to prevent overheating damage
Resolves early-shutoff, won't-restart-until-cool, and intermittent cycling symptoms
Fits 28+ GE, Hotpoint, and Kenmore dryer and washer-dryer combo models
Straightforward swap — typically 15–30 minutes with basic hand tools
Product Specifications
Part Number
XPWE4M137
OEM Part Number
WE4M137
Part Type
Dryer High Limit Thermostat (Auto-Reset)
Condition
Aftermarket Replacement
Temperature Rating
L315-65F (Opens ~315°F, Auto-Resets on Cooling)
Location
Upper Right Side of Heater Housing
Application
GE, Hotpoint & Kenmore Dryers
Installation Notes
⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Remove the dryer's rear or front panel per your model's service guide to access the heater housing — the thermostat is mounted on its upper right side. Disconnect the wire terminals from the old thermostat, noting their positions, and remove the mounting screw holding it in place. Install the new thermostat in the same position and reconnect the wire terminals. Before closing the dryer back up, clean out the lint trap and check the exhaust vent for restrictions — a clogged vent is the most common cause of this thermostat tripping repeatedly, and clearing it now can prevent a repeat failure.
Frequently Asked Questions
My dryer shuts off a few minutes into the cycle and won't restart — is this the part I need?
Yes, this is a classic symptom of a failing high limit thermostat. It's designed to cut power when the dryer overheats and automatically reset once things cool down, so if your dryer won't restart until it's had time to sit, this thermostat is a likely cause.
Is this a one-time fuse like the thermal fuse, or does it reset itself?
This is an auto-resetting thermostat, not a one-time thermal fuse. It opens to cut power when the dryer overheats, then closes again automatically once the unit cools — it doesn't need to be replaced every time it trips. If yours has failed and won't reset or close again, that's when replacement is needed.
Why does my dryer keep tripping this thermostat?
Repeated tripping is usually caused by restricted airflow — a clogged lint trap, a crushed or blocked exhaust duct, or a bird's nest or lint buildup in the outside vent hood — or a failed cycling thermostat elsewhere in the heating circuit. Clear the airflow path when you replace this thermostat, or the new one may trip again.
How do I test if this thermostat has failed?
With the dryer unplugged, you can test the thermostat with a multimeter for continuity across its terminals at room temperature. No continuity when it should be closed (cool) is a sign it has failed and needs replacement.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 279816 Dryer Thermostat Kit
The XPARTCO 279816 is an aftermarket replacement thermal fuse and high-limit thermostat combo kit for Whirlpool-built dryers. These are the dryer's two thermal safety devices, and they're bundled together in this kit because they tend to fail around the same time and share a common cause: restricted airflow that lets heat build up beyond safe levels. The high-limit thermostat is the first line of defense, opening at approximately 250°F (L250-80F) to interrupt heating if the dryer runs too hot. If that isn't enough to bring the temperature back down, the thermal fuse is the final failsafe, opening permanently at approximately 309°F to cut power to the dryer entirely.
That's an important distinction between the two parts: the high-limit thermostat is a cycling safety device that can open and close as temperature rises and falls, while the thermal fuse is a one-time device — once it blows, it's done, and the dryer won't run again until it's replaced. This kit includes both components plus mounting screws and a wiring set with a jumper wire and extra terminals, which is used specifically when replacing an older-style thermostat that had a wire pressing directly onto the heating element. A dryer that won't start at all, with no lights or response, usually means the thermal fuse has blown; a dryer that runs but won't heat, or that stops heating partway through a cycle, points more toward the thermostat. It directly replaces 2651, 279816VP, 3399848, 3977393, 3390291, AP3094244, AH334299, EA334299, EAP334299, PD00002348, and PS334299.
Quick Answer
The XPARTCO 279816 Dryer Thermostat Kit fixes Whirlpool-built dryers that won't start at all, won't heat, or stop heating partway through a cycle. Includes a thermal fuse (opens ~309°F), a high-limit thermostat (opens ~250°F), mounting screws, and a wiring set. Replaces 2651, 279816VP, 3399848, 3977393, 3390291, AP3094244, AH334299, EA334299, EAP334299, PD00002348, PS334299. Always inspect and clean the dryer venting when replacing this kit — a blown fuse or tripped thermostat is a symptom of restricted airflow, and skipping this step means the new parts are likely to fail again.
Common Problems This Part Fixes
Dryer won't start at all — no lights, no tumble, no response to any button
Dryer runs and tumbles but produces no heat
Dryer heats for a while, then stops heating partway through a cycle
Dryer that stopped working suddenly, especially after running unusually hot
Clothes coming out extremely hot right before the dryer stopped heating or stopped entirely
Repeated blown fuses or tripped thermostats on a dryer with a known venting restriction
Continuity test shows an open circuit across the old fuse or thermostat
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer thermostat kit directly replaces the following OEM and cross-reference part numbers:
279816, 279816VP, 3399848, 3977393, PD00002348, AWP39198, EAP334299, AH334299, EA334299, AP3094244, PS334299.
3977393 is the thermal fuse component and 3390291 is the "new-style" high-limit thermostat component included in this kit. If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This thermostat kit is compatible with select Whirlpool-built dryers across the Whirlpool family of brands, including:
Whirlpool electric and gas dryers — WED series
Maytag electric and gas dryers — NED series (select Whirlpool-built models)
Admiral, Amana, Crosley, Estate, Inglis, Magic Chef, and Roper dryers (select models)
Kenmore and KitchenAid dryers (select Whirlpool-built models)
Verified model numbers include: WED6200SW1, NED4600YQ0, NED4600YQ1, NED4655EW1, and LER3624EQ.
Note: The wiring set included in this kit is designed for replacing an older-style thermostat that used a wire pressed directly onto the heating element. If your dryer uses the true old-style push-on thermostat and fuse combination (part 3977767), you'll need a different kit (commonly listed as APN197) instead of this one. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which kit fits your dryer.
Key Features
Complete combo kit — thermal fuse, high-limit thermostat, mounting screws, and wiring set in one package
Thermal fuse opens at approximately 309°F as a one-time, non-resettable safety cutoff
High-limit thermostat opens at approximately 250°F (L250-80F) as a cycling safety device
Resolves "won't start at all," "runs but doesn't heat," and "stops heating mid-cycle" symptoms
Wiring set includes jumper wire and extra terminals for older-style push-on thermostat connections
Replaces 2651, 279816VP, 3399848, 3977393, 3390291, AP3094244, AH334299, EA334299, EAP334299, PD00002348, and PS334299
Compatible with Whirlpool, Maytag, Admiral, Amana, Crosley, Estate, Inglis, Magic Chef, Roper, Kenmore, and KitchenAid dryers
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
279816
OEM Part Number
279816
Part Type
Dryer Thermal Fuse & High-Limit Thermostat Kit
Condition
Aftermarket Replacement
Kit Contents
Thermal fuse, high-limit thermostat, mounting screws, wiring set
Thermal Fuse Opening Temp
Approx. 309°F (one-time, non-resettable)
High-Limit Thermostat Opening Temp
Approx. 250°F / L250-80F (cycling)
Wiring Set
Jumper wire + extra terminals for older-style push-on thermostats
Quantity
1 kit
Compatible Brands
Whirlpool, Maytag, Admiral, Amana, Crosley, Estate, Inglis, Magic Chef, Roper, Kenmore, KitchenAid
Installation Notes
⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel: remove the screws securing the panel to reach the blower housing area where both the thermal fuse and high-limit thermostat are mounted, usually close together near the heating element or blower assembly. Photograph the wiring before disconnecting anything, and note whether your old thermostat used a push-on wire connection at the heating element — if so, use the included jumper wire and extra terminals to make the new connection correctly. Remove the mounting screws holding each old component in place and disconnect their wire terminals. Before installing the new parts, test the old fuse and thermostat with a multimeter to confirm which one (or both) is actually open, rather than assuming. This is the most important step: fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. A blown fuse or tripped thermostat is a symptom of restricted airflow, and skipping this step means the new parts are likely to fail again. Install the new thermal fuse and thermostat from this kit in the same mounting positions, reconnect the wire terminals (using the included wiring set if applicable), and secure the mounting screws. Reinstall the rear panel, restore power, and run a test cycle to confirm normal heating and shutoff behavior. Tools needed: Phillips or nut driver (model-dependent), multimeter, vent brush or vacuum attachment for cleaning ductwork, work gloves.
Frequently Asked Questions
Why does this kit include two different parts instead of just one?
The thermal fuse and high-limit thermostat work together as a two-stage safety system, and they're bundled because they commonly fail together — both are reacting to the same underlying overheating condition, usually restricted airflow. The high-limit thermostat trips first at a lower temperature and can cycle open and closed; if that's not enough to control the heat, the thermal fuse trips at a higher temperature and shuts the dryer down permanently until replaced. Replacing both together addresses the full safety chain rather than just one link in it.
My dryer won't start at all versus my dryer runs but doesn't heat — which part is which?
A dryer with absolutely no response — no lights, no tumbling, nothing — usually points to the thermal fuse, since it's wired to cut power more broadly when it blows. A dryer that tumbles and runs normally but produces no heat, or that starts heating and then stops partway through, points more toward the high-limit thermostat. Testing both components with a multimeter will confirm exactly which one has failed.
I replaced both parts and the dryer failed again. What's going on?
This is a strong sign that the underlying cause — almost always restricted airflow — was never addressed. Neither of these parts fails from age; they trip or blow because the dryer overheated. If new parts fail again, thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. If airflow checks out and the parts still fail, have the heating element checked as well, since a shorted element can also drive excess heat.
Do I need the wiring set included in this kit?
Only if your dryer's original thermostat used a wire that pressed directly onto the heating element (an older-style connection) rather than a standard push-on terminal. If your dryer already uses a straightforward terminal connection, you can skip the jumper wire and extra terminals and connect the new thermostat directly.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the opening temperatures, terminal configuration, and mounting positions of the original 279816 thermal fuse and high-limit thermostat kit used in compatible Whirlpool, Maytag, and related dryers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 279769 Dryer Thermostat Kit
The XPARTCO 279769 is an aftermarket replacement thermal cut-off and high-limit thermostat kit for Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers. This kit bundles two components that guard against overheating at different thresholds: the 3390291 high-limit thermostat (rated L250-80F) monitors internal temperature and interrupts power at approximately 250°F to prevent overheating, then resets itself automatically once the dryer cools — no replacement needed after each trip. The 3977394 thermal cut-off fuse is the backup: rated at 352°F, it's a one-time safety device that permanently opens the circuit if temperatures climb high enough that the thermostat alone didn't prevent an overheat.
These two parts are sold together and should be replaced together as a set, since they protect the same circuit and tend to be stressed by the same underlying problem. Whirlpool's own guidance is direct: when the thermal cut-off fails, it usually indicates a venting problem, and failing to correct that airflow issue will cause repetitive failures even with new parts installed. Symptoms include the dryer not heating, clothes coming out extremely hot, or the dryer not running at all. This kit is commonly used alongside heating element 4391960. It directly replaces 279769, 279548, 2796769, 279769VP, 2821, 2004, 3387812, 3389946, 3398671, 3977394, 695563, 80001, SET184, SET198, TJSET198, ET184, AP3094224, AH334278, EA334278, EAP334278, PD00002485, PS334278, WP3390291, AP6008306, 3390291, 696397, and PS11741441. As an aftermarket replacement, the 279769 kit is built to OEM-equivalent quality standards.
Quick Answer
The XPARTCO 279769 Dryer Thermostat Kit fixes Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers with no heat, no power at all, or clothes coming out dangerously hot. Includes the 3390291 high-limit thermostat (250°F, auto-resetting) and the 3977394 thermal cut-off fuse (352°F, one-time). Replaces 279548, 2796769, 279769VP, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AP3094224, PS334278, WP3390291, AP6008306, 3390291, 696397, PS11741441. Always inspect and clean the exhaust venting when replacing this kit — a blown thermal fuse is a symptom of restricted airflow, and skipping the vent check leads to repeat failures.
What's In The Kit
Component
Rating
Function
3390291 High-Limit Thermostat
L250-80F (~250°F)
Interrupts power to prevent overheating, resets automatically once the dryer cools.
3977394 Thermal Cut-Off Fuse
352°F
One-time backup safety device — permanently opens the circuit if temperature exceeds safe limits. Cannot reset.
Common Problems This Kit Fixes
Dryer won't start at all — no lights, no tumble, no response
Dryer runs but produces no heat
Clothes coming out extremely hot, hot enough to be uncomfortable to handle
Dryer that stopped working suddenly after running unusually hot
Repeated thermal cut-off failures on a dryer with a known venting issue
Dryer that shuts off prematurely mid-cycle
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer thermostat kit directly replaces the following OEM and cross-reference part numbers:
279769, 2004, 279548, 2796769, 279769VP, 2821, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AH334278, EA334278, AP3094224, OEM9282681, SET184, SET198E, AP334278, L250-80F, PS334278, AWP39149, PD00002485.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This thermostat kit is compatible with select Whirlpool electric dryers, and also fits select Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral dryers built on the Whirlpool platform, including model numbers such as:
7MWET4027HW0
WET3300XQ0
WET4027EW0, WET4027EW1
WET4027HW0, WET4027HW1, WET4027HW2
WETLV27FW0, WETLV27HW0, WETLV27HW1, WETLV27HW2, WETLV27HW3
YWET4027EW1, YWET4027HW0, YWET4027HW1, YWET4027HW2
Note: This kit was used on Whirlpool-built electric dryers primarily from 1985 to 1995. Always verify your full model number before ordering, since Whirlpool used several different thermostat and fuse designs across its dryer lineup over the years. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement built to match Whirlpool's factory-specified thresholds for both components
2-piece kit: 3390291 high-limit thermostat (250°F, auto-resetting) and 3977394 thermal cut-off fuse (352°F, one-time)
Resolves "no heat," "no power at all," and "clothes coming out extremely hot" symptoms
Addresses two overheat-protection thresholds in the same circuit at once
Commonly used alongside heating element 4391960
Direct drop-in replacement for both original components
Replaces 279548, 2796769, 279769VP, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AP3094224, PS334278, WP3390291, AP6008306, 3390291, 696397, and PS11741441
Compatible with Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Kit Part Number
279769
Kit Contents
1x High-Limit Thermostat (3390291), 1x Thermal Cut-Off Fuse (3977394)
OEM Part Number
279769
Condition
Aftermarket Replacement
Brand
Whirlpool
High-Limit Thermostat Rating
L250-80F (~250°F, auto-resetting)
Thermal Fuse Rating
352°F (one-time, non-resettable)
Companion Heating Element
4391960 (commonly used together)
Repair Difficulty
Easy to Moderate — basic tools required
Compatible Brands
Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, Admiral
Installation Notes
⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel, near the heating element and blower housing where both components are mounted. Photograph the wiring connections before disconnecting anything, since the thermostat and fuse can be easy to swap positions by mistake. Remove each old component from its mounting position, noting orientation, and disconnect its wiring. Before reassembling, fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. When the thermal cut-off fails, it usually indicates a venting problem, and failing to correct that airflow issue will cause repetitive failures even with these new parts installed. Install the new 3390291 thermostat and 3977394 thermal fuse from this kit in the same positions as the parts they replace, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), work gloves.
Frequently Asked Questions
My clothes are coming out extremely hot, hot enough to burn my hands. Is this the right kit?
Yes, this is a documented symptom this kit addresses. If the high-limit thermostat fails to regulate temperature correctly, the dryer can run far hotter than it should, producing dangerously hot clothing at the end of a cycle. Whirlpool's own parts support has specifically pointed customers with this exact complaint toward this kit. Stop using the dryer if you notice this symptom and replace both components promptly.
Why do I need to replace both the thermostat and the fuse together?
These two parts protect the same circuit at different thresholds and tend to fail from the same underlying cause. If the high-limit thermostat isn't regulating temperature correctly, the thermal fuse often ends up blowing as the backup safety measure. Replacing only one risks the other failing again shortly after, so they're sold and serviced together as a set.
I replaced this kit and the dryer failed again. What should I check?
This is a strong sign the underlying cause — almost always restricted airflow — was never addressed. Thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. Failing to correct a venting issue will cause repetitive failures of this kit even when it's brand new.
Should I replace the heating element at the same time?
It's worth considering if your dryer's heating element (commonly 4391960 on compatible models) is original and has been running alongside a failing thermostat, since sustained overheating can stress the element as well. It's not required, but since you'll already have the panel open for this repair, it's a reasonable time to inspect the element for visible damage.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the temperature thresholds and mounting configuration of the original 279769 high-limit thermostat and thermal cut-off fuse kit used in compatible Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 8557403 Dryer High-Limit Thermostat with Thermistor Replaces WP8557403
The XPARTCO 8557403 is an aftermarket replacement dryer high-limit thermostat and thermistor sensor assembly compatible with a wide range of Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Jenn-Air, Roper, Admiral, Norge, and Magic Chef electric dryers — including the Whirlpool Duet and Maytag MED series. This single component combines two functions: the high-limit thermostat (rated L146-44C, opens at 295°F) acts as a resettable safety switch that cuts power to the heating element if the dryer air temperature exceeds safe limits, and the integrated 50-ohm thermistor continuously monitors air temperature and sends resistance-based readings to the control board to regulate the drying cycle.
When this part fails — whether the thermostat opens permanently or the thermistor provides incorrect temperature data — the dryer may produce no heat, run too hot, take too long to dry, overheat, or display temperature-related error codes. It measures 1-5/8"L x 1-5/8"W x 2"H with approximately 1-5/8" between mounting holes and is constructed from black/gray plastic and metal. It directly replaces WP8557403, 1180102, AP6013164, EAP11746386, PD00003588, and PS11746386. Note: the exhaust duct thermostat and thermal fuse are separate parts — if those have also failed, they must be ordered separately. Installs in 15–20 minutes with basic hand tools.
Quick Answer
The XPARTCO 8557403 Dryer High-Limit Thermostat with Thermistor fixes Whirlpool Duet, Maytag MED, and related dryers with no heat, overheating, or erratic temperature. Combined part: L146-44C high-limit thermostat (opens at 295°F, auto-resets) + 50-ohm NTC thermistor. 1-5/8"L x 1-5/8"W x 2"H, ~1-5/8" between mounting holes. Replaces WP8557403, 1180102, AP6013164, EAP11746386, PD00003588, PS11746386. For Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Jenn-Air, Roper, and Admiral electric dryers.
Common Problems This Part Fixes
Dryer produces no heat — high-limit thermostat has failed open
Dryer overheating — thermostat not opening at the correct temperature
Dryer takes too long to dry — thermistor providing incorrect temperature readings to the control board
Dryer cycling on and off erratically — thermistor fault causing incorrect cycle control
Temperature-related error codes on models with digital displays
Multimeter test shows open circuit on the thermostat at room temperature
Multimeter test shows open or shorted thermistor (not ~50 ohms at room temperature)
Replaces Part Numbers
This thermostat/thermistor assembly directly replaces the following OEM and cross-reference part numbers:
WP8557403, 8557403, 1180102, AP6013164, AWP48681, EAP11746386, PD00003588, PS11746386.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This high-limit thermostat and thermistor is compatible with select electric dryers only from the following brands:
Whirlpool electric dryers — Duet, WED5000, WED5500, WED5600, WED5620, WED8000, WED8200, WED8500, WED9200, WED92HEF, WED7000 series and related models
Maytag electric dryers — MED3500, MED5630, MED6630, MED7230, MEDB835 series and related models
Kenmore / Sears electric dryers — 110-series (Whirlpool-built models)
Amana electric dryers (select models)
KitchenAid electric dryers (select models)
Jenn-Air electric dryers (select models)
Roper electric dryers
Admiral electric dryers
Norge electric dryers
Magic Chef electric dryers
Note: This part is for electric dryers only. The exhaust duct thermal fuse and cycling thermostat are separate parts — if those have also failed, they must be ordered separately. Always verify your model number before ordering.
Key Features
Combined high-limit thermostat and thermistor in a single assembly — replaces both functions in one part
High-limit thermostat rated L146-44C — opens at 295°F (146°C), resets automatically when cooled
Integrated 50-ohm NTC thermistor — continuously monitors dryer air temperature and sends readings to the control board for cycle regulation
Dimensions: 1-5/8"L x 1-5/8"W x 2"H; approx. 1-5/8" between mounting holes
Black/gray plastic and metal construction
Electric dryers only — not for gas dryer models
Replaces WP8557403, 1180102, AP6013164, EAP11746386, PD00003588, and PS11746386
Compatible with Whirlpool Duet, Maytag MED, Kenmore, Amana, KitchenAid, Jenn-Air, Roper, Admiral, Norge, and Magic Chef electric dryers
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY repair — installs in 15–20 minutes with basic hand tools
Product Specifications
Part Number
8557403
OEM Part Number
WP8557403
Part Type
Dryer High-Limit Thermostat with Integrated Thermistor Sensor
Condition
Aftermarket Replacement
Application
Electric Dryers Only
Thermostat Rating
L146-44C — opens at 295°F (146°C), auto-resets
Thermistor
50-ohm NTC (at room temperature ~25°C)
Dimensions
1-5/8"L x 1-5/8"W x 2"H
Mounting Hole Spacing
Approx. 1-5/8" center to center
Color
Black / Gray
Material
Plastic / Metal
Compatible Brands
Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Jenn-Air, Roper, Admiral, Norge, Magic Chef
Installation Notes
⚠️ Unplug Dryer Before Starting — Electric Dryers Only Disconnect power before beginning. The 8557403 thermostat/thermistor assembly is typically located on the heating element housing or duct inside the dryer — access it by removing the back panel. On Whirlpool Duet and Maytag front-load-style dryers, the component may be accessible by removing the lower front panel. Photograph all wire connections before disconnecting — the thermistor wires and thermostat wires must be reconnected to the correct terminals. Remove the two mounting screws and pull the old assembly off. Note the position and orientation before removing. Install the new 8557403 assembly in the same position and orientation, reconnect all wires, and reinstall the mounting screws and panel. Restore power and run a test heat cycle to confirm normal operation. Tools needed: Phillips screwdriver, 1/4" nut driver.
Frequently Asked Questions
What makes this part unusual — why does it combine a thermostat and a thermistor?
The WP8557403 is a combined assembly used on newer Whirlpool Duet and Maytag MED series dryers that use electronic temperature control rather than purely mechanical thermostats. The high-limit thermostat (L146-44C) provides the traditional safety function — it opens the circuit if dryer temperature exceeds 295°F. The integrated NTC thermistor continuously reports resistance-based temperature data to the electronic control board, which uses the data to regulate the heating element and control cycle timing. Both functions are built into a single compact housing, making this a unique part that replaces what older dryers used to handle with separate components.
How do I test the thermostat and thermistor?
Set your multimeter to continuity or resistance mode. For the thermostat portion: probe the thermostat terminals — at room temperature, a working thermostat shows closed continuity (near-zero resistance). An open circuit at room temperature confirms the thermostat has failed. For the thermistor portion: probe the thermistor terminals — at room temperature (approximately 25°C/77°F), a working 50-ohm NTC thermistor should read approximately 50 ohms. A reading of zero ohms (shorted) or open circuit (no continuity) confirms the thermistor has failed. Either failure mode warrants replacing the complete 8557403 assembly.
What is the difference between 8557403 and WP8557403?
These are the same part. WP8557403 is the updated Whirlpool OEM part number that superseded the original 8557403. The 1180102 is also a cross-reference for this same assembly. This aftermarket replacement is compatible with all of these numbers.
Do I also need to replace the thermal fuse or cycling thermostat?
The 8557403 replaces the high-limit thermostat and thermistor mounted on the heating element housing area. The exhaust duct thermal fuse (WP3392519 on most Whirlpool-family dryers) and cycling thermostat (WP3387134) are separate components located on the exhaust duct and are not included in or replaced by the 8557403. If your dryer has no heat, test all thermal components before ordering — check the 8557403 assembly, the thermal fuse, and the cycling thermostat, then order only what has failed. If an overheating event caused the high-limit to fail, the other thermal components may be stressed as well.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from plastic and metal with an L146-44C thermostat and 50-ohm NTC thermistor to match the specifications and performance of the original WP8557403 assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
DE47-20034A Microwave Genuine High Limit Thermostat
Thermal cutout.
High limit thermostat. Open for continuity at room temperature, closes when it gets hot.
Fits Samsung over counter microwaves.
Replaces Part Numbers:DE47-20034A, AP4219754, PS4226431.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO WB27X11212 Microwave Thermostat – Compatible with GE, Hotpoint & Kenmore Microwaves
Product Description
Ensure safe microwave operation with the XPARTCO WB27X11212 Microwave Thermostat. This high-quality aftermarket replacement monitors internal temperatures and shuts off power if overheating is detected. A faulty thermostat can cause the microwave to shut off unexpectedly, fail to heat, or stop mid-cycle. Replacing it with this reliable XPARTCO thermostat restores proper temperature regulation and protects critical internal components.
Replaces Part Numbers
WB27X11212, 3026293, SE-7350-006, KSD201 - 120C, WB24X28948, WB27X10854, AP5791056, PS8754627.
Compatibility
This replacement microwave thermostat fits select GE, Hotpoint, and Kenmore microwave ovens.
Example compatible models include (but are not limited to):GE JVM1540DM5BB, JVM3160RFSSHotpoint RVM5160DHBBKenmore 363.62709300
Always verify your microwave’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Designed to match OEM temperature-sensing performance
🌡️ Overheat Protection – Prevents damage by cutting power at unsafe temperatures
💰 Cost-Effective Repair – Reliable solution without OEM pricing
🛠️ Direct-Fit Design – Installs easily with existing mounting and wiring
🛡️ Fixes Common Issues – Solves random shut-offs, no-heat conditions, or thermal errors
📐 Product Specification
Part Number: WB27X11212
Component Type: Microwave Thermostat / Thermal Switch
Temperature Rating: OEM-equivalent cutoff
Material: Metal housing with bimetal thermal disc
Mounting: Screw-mounted
Compliance: Built to OEM-equivalent quality standards (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, needle-nose pliers
⚠️ Safety First: Unplug the microwave and discharge high-voltage components before servicing. Microwave repairs involve HIGH VOLTAGE.
Steps:
Disconnect power and remove the microwave cover.
Locate the thermostat mounted near the magnetron or cavity.
Disconnect wires and remove mounting screws.
Install the new XPARTCO WB27X11212 thermostat.
Reconnect wiring, reinstall the cover, and restore power.
Test microwave operation.
⏱️ Time Required: 15–25 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Appliance Parts Supplier
🔄 30-Day Return Policy
Protect your microwave and restore safe operation — Add to Cart Now for a dependable, budget-friendly repair!
XPARTCO 3387134 Dryer Cycling Thermostat
The XPARTCO 3387134 is an aftermarket replacement dryer cycling thermostat, the operating thermostat that controls drying temperature. It switches the heating element off when the dryer reaches its set temperature and back on after it cools, keeping the inside of the dryer at a steady temperature throughout the cycle. This one is rated L155-25: it cuts out at approximately 155°F and cycles back on once the temperature drops about 25°F.
When a cycling thermostat fails, the dryer may stop heating, run too hot, or keep heating after the drum has stopped. This is a direct-fit aftermarket replacement for the original Whirlpool WP3387134, and it fits a wide range of Whirlpool-built dryers sold under the Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Crosley, Estate, Amana, and other brand names.
Quick Answer
The XPARTCO 3387134 Cycling Thermostat fixes a Whirlpool-built dryer that isn't heating, runs too hot, or has inconsistent drying temperatures. Rated L155-25, it cycles the heating element off at about 155°F and back on after a 25°F drop. Classic symptom: clothes come out damp or the dryer runs excessively hot, with no sign of a clogged vent.
Common Problems This Part Fixes
Dryer not heating
Dryer running too hot
Inconsistent drying temperatures
Heat staying on after the drum has stopped
Dryer won't start or the timer doesn't advance, if the thermostat has failed
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This cycling thermostat directly replaces the following part numbers:
3387134, WP3387134, 3387135, 3387139, 306910, 3-6910, 2011
These numbers span several generations of Whirlpool's own part numbering for this thermostat as model lines were updated. All are the correct replacement regardless of which number appears on your dryer's parts diagram.
Compatibility
This thermostat fits a wide range of Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Crosley, Estate, Amana and related dryers, including these examples:
Kenmore 11060012000, 11060012001, 11060022010, 11060172000, 11060232000, 11060602990
Numerous additional Whirlpool-built dryer models
Note: This is the cycling (operating) thermostat, not the high limit thermostat or the thermal fuse, which are separate safety parts. The models above are a sample, not a full list. Confirm your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering.
Key Features
Direct-fit aftermarket cycling thermostat for Whirlpool-built dryers
Rated L155-25: cuts out at about 155°F and cycles back on after a 25°F drop
Keeps dryer temperature steady by cycling the heating element on and off
Resolves no-heat, overheating, and inconsistent-temperature symptoms
Fits Whirlpool, Kenmore, Maytag, KitchenAid, and other Whirlpool-built dryers
Medium-difficulty repair with basic hand tools
Product Specifications
Part Number
XP3387134
OEM Part Number
3387134, WP3387134
Part Type
Dryer Cycling Thermostat
Condition
Aftermarket Replacement
Temperature Rating
L155-25 (Cuts Out ~155°F, 25°F Differential)
Application
Whirlpool, Kenmore, Maytag, KitchenAid & Related Dryers
Installation Notes
⚠️ Unplug Power Before Installing
Unplug the dryer or switch off its circuit breaker before beginning, and shut off the gas supply first on gas models. Wear work gloves, as the cabinet edges are sharp. Remove the panel that gives access to the heater housing per your model's service guide, note the wire terminal positions, and disconnect them from the old thermostat. Remove the thermostat, install the new one in the same position, and reconnect the wires. A screwdriver and needle-nose pliers are typically all you need. Before closing the dryer, clean the lint trap and check the exhaust vent for restrictions, since poor airflow is a common cause of overheating.
Frequently Asked Questions
My dryer isn't heating or runs too hot. Is this the part I need?
A failed cycling thermostat can cause either symptom. It may stay open and prevent heat, or stay closed and let the dryer overheat. Check for a clogged vent and test the thermostat for continuity before replacing it.
What's the difference between the cycling thermostat and the high limit thermostat?
The cycling thermostat controls normal drying temperature by switching the heating element on and off. The high limit thermostat and thermal fuse are separate safety devices that cut power if the dryer overheats. This listing is for the cycling thermostat only.
How do I test this thermostat?
With the dryer unplugged and the wires removed, check for continuity across the terminals with a multimeter at room temperature. A properly working cycling thermostat should show continuity when cool. No continuity means it has failed.
Will this fit my dryer?
It fits many Whirlpool-built dryers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping
✓ Quality Aftermarket Parts
✓ Compatibility Support
✓ Secure Checkout
XPARTCO 6931EL3002M Dryer Blower Thermostat
The XPARTCO 6931EL3002M is an aftermarket replacement dryer blower thermostat, made to replace LG part 6931EL3002M, for select LG and Kenmore dryers. The thermostat is overheat protection on the dryer's blower housing, and it shuts the dryer down if it gets too hot. When it fails, the dryer may stop heating or may not start at all.
This is an aftermarket replacement from XPARTCO, not a genuine LG part. It is sold individually. Check your model number before ordering, because LG uses several similar dryer thermostats with different part numbers.
Quick Answer
The XPARTCO 6931EL3002M Dryer Blower Thermostat replaces the blower thermostat on a compatible LG or Kenmore dryer when it has failed. Replaces 6931EL3002A and 6931EL3002K. Classic symptoms: the dryer won't heat, won't start, or clothes take too long to dry.
Common Problems This Part Fixes
Dryer not heating
Dryer won't start
Clothes taking too long to dry or staying damp
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This blower thermostat is made to replace the following LG part numbers:
6931EL3002M, 6931EL3002A, 6931EL3002K, ALG51962, AP5782317, EAP8747887, PD00023476, PS8747887
If your old thermostat shows a different number, contact our support team and we'll check whether it matches.
Compatibility
This blower thermostat is listed for LG and Kenmore dryers, including these examples:
LG DLEX8500V, DLEX8100V, DLEX8000V, DLEX8000W, DLEX9500K, DLEX7700VE
LG DLEX2650W, DLEX3370W, DLE3500W, DLG7188WM, DLGX7801VE
Kenmore Elite 79681963710, 79681962710
Note: The models above are a sample of several hundred listed by retailers, not a full list. LG dryers also use separate high-limit thermostats with different part numbers, such as 6931EL3003C and 6931EL3003D, which are not the same part. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering.
Key Features
Aftermarket replacement for the LG 6931EL3002M dryer blower thermostat
Overheat protection on the dryer's blower housing
Cross-references earlier LG part numbers 6931EL3002A and 6931EL3002K
Sold individually
Product Specifications
Part Number
XP6931EL3002M
OEM Part Number
6931EL3002M
Part Type
Dryer Blower Thermostat
Condition
Aftermarket Replacement
Quantity
1 Thermostat
Application
Select LG and Kenmore Dryers
Installation Notes
⚠️ Disconnect Power Before Installing Unplug the dryer before you begin and wear work gloves. Remove the panels needed to reach the blower housing for your model, then note which wire goes to which terminal and disconnect them. Remove the old thermostat, install the new one, and reconnect each wire to its original terminal, because a wire on the wrong terminal can damage the thermostat. Refit the panels, restore power, and run a test cycle.
Frequently Asked Questions
My dryer isn't heating or won't start. Is this the part I need?
It can be. Dryers use several thermostats and a thermal fuse, and the same symptoms can come from a clogged vent, the igniter or heating element, or the control board. Check the vent and test the thermostats before replacing this one.
Is this an OEM or aftermarket part?
This is an aftermarket replacement from XPARTCO, made to replace LG part 6931EL3002M. If you specifically need a genuine LG part, contact our support team.
Is this the same as the high-limit thermostat?
No. LG sells separate high-limit thermostats, such as 6931EL3003C and 6931EL3003D. Match the part number on your old thermostat before ordering.
Will this fit my dryer?
It is listed for many LG and Kenmore dryers, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
31001192 Genuine OEM Dryer Cycling Thermostat
Replaces Part Numbers: WP31001192, 31001192, 487706, 53-2880, AP6007590, PS11740707.
Description: This Dryer Cycling Thermostat is a Genuine OEM replacement part for Select Maytag, Kenmore, Whirlpool dryer models. It monitors internal temperatures and cycles power to the heating element accordingly. The thermostat ensures the drying air reaches and maintains the optimal heat level selected for fast, effective drying results
XPARTCO 35001092 Dryer Thermostat – Replaces WP35001092 – Compatible with Whirlpool, Maytag & Kenmore Dryers
Product Description
Maintain proper dryer temperature and consistent drying results with the XPARTCO 35001092 Dryer Thermostat. This High Limit Thermostat is a replacement part for specific dryer models. It plays a role in the safety and efficiency of the dryer's operation by monitoring and regulating the temperature within the dryer. This thermostat acts as a safety device, cutting off the heat source if the internal temperature exceeds safe levels, preventing potential overheating and fire hazards.
Replaces Part Numbers
WP35001092, 35001092, 1122485, PD00004704, EAP11741822, AP6008682, PS11741822.
Compatibility
This replacement dryer thermostat fits select Whirlpool, Maytag, Kenmore, Amana, Crosley, and Estate electric dryers.
Example compatible models include (but are not limited to):Whirlpool WED4815EW1, Maytag MEDC215EW1, Kenmore 110.65132411.
Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Matches OEM temperature cycling performance
🌡️ Accurate Heat Regulation – Maintains safe, consistent drying temperatures
🔧 Reliable Thermal Control – Helps prevent overheating and heat loss
💰 Cost-Effective Repair – Quality alternative to OEM thermostats
🛡️ Fixes Common Issues – Solves no heat, overheating, long dry times, or blown fuses
📐 Product Specification
Part Number: 35001092
Component Type: Dryer Operating Thermostat
Application: Heater or exhaust temperature regulation
Material: Heat-resistant metal thermostat housing
Mounting: Screw-mounted
Compliance: Built to OEM-equivalent quality standards (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, nut driver
⚠️ Safety First: Always unplug the dryer before servicing to avoid electrical shock.
Steps:
Disconnect dryer power and remove the rear access panel.
Locate the thermostat on the heater housing or exhaust duct.
Disconnect wiring and remove the old thermostat.
Install the new XPARTCO 35001092 thermostat.
Reconnect wiring, reinstall the panel, and restore power.
Run a test cycle to confirm proper heating.
⏱️ Time Required: 10–15 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Appliance Parts Supplier
🔄 30-Day Return Policy
Restore proper dryer temperature control — Add to Cart Now for a dependable, budget-friendly repair!
AGM30045804 Genuine OEM LG Dryer Thermistor and Thermostat Kit
The AGM30045804 is a genuine LG OEM high-limit thermostat and thermistor kit for LG dryers. These two components work together in the same temperature-regulation circuit: the thermistor is a temperature sensor, mounted in the blower housing with its wire harness included, that continuously reports drum temperature to the control board so it can fine-tune heat output throughout the cycle. The high-limit thermostat is a safety switch that automatically shuts off the heating element if temperatures climb past a safe threshold, then resets itself once the dryer cools, without needing to be replaced the way a thermal fuse does.
Because these two parts share the same circuit and tend to wear or fail around a similar timeline, LG sells and services them together as one kit rather than as separate individual parts. Symptoms of failure in this circuit include the dryer overheating (which can scorch clothing or, left unaddressed, pose a fire risk), the dryer running with little or no heat, drying times that have become inconsistent, an error code related to temperature control on the display, or clothes coming out damp after a full cycle. It directly replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, and PS16732335.
Quick Answer
The AGM30045804 Genuine OEM LG Dryer Thermistor and Thermostat Kit fixes LG (and select Kenmore, GE-branded LG-built) dryers with overheating, little or no heat, inconsistent drying times, a temperature-related error code, or clothes coming out damp after a full cycle. High-limit thermostat + thermistor with wire harness. Replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, PS16732335. If you've already replaced the high-limit thermostat alone and the problem returns, this combined kit — which also addresses the thermistor — is the next step.
What's In The Kit
Component
Function
High-Limit Thermostat
Automatically shuts off the heating element if temperature exceeds safe limits, then resets itself once the dryer cools.
Thermistor (with wire harness)
Continuously senses drum/blower housing temperature and reports it to the control board to regulate heat output throughout the cycle.
Common Problems This Kit Fixes
Dryer overheating, sometimes scorching or damaging clothing
Dryer running with little or no heat
Inconsistent drying times — cycle shuts off too early or runs longer than necessary
Temperature-related error code displayed on the control panel
Clothes remaining damp after a full drying cycle
High-limit thermostat that keeps tripping repeatedly
Dryer that has already had its high-limit thermostat replaced once but the problem returned
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer thermistor and thermostat kit directly replaces the following OEM and cross-reference part numbers:
AGM30045804, 6931EL3003C, 6931EL3004B, 6931EL3002B, 6931EL3003F, 6931EL3003G, 6323EL2001B, ALG53406, AP7206815, EAP16732335, PD00079467, PS16732335
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This kit is compatible with select LG dryers, and also fits select Kenmore and GE-branded dryers built on the LG platform.
Note: A specific verified model list was not consistently available across sources at the time this page was built. Some parts diagrams reference additional related thermostat components (such as a separate blower thermostat) beyond what's included in this kit — if your repair involves more than a high-limit thermostat and thermistor, or if you're unsure exactly what's failed on your model, contact our support team with your model number and we'll help confirm which parts you need before you order.
Key Features
Genuine LG OEM part — factory-specified resistance values and switch thresholds
Combined kit addresses the high-limit thermostat and thermistor together, since both share the same temperature-regulation circuit
Resolves "overheating," "little or no heat," "inconsistent drying," and "damp clothes after a full cycle" symptoms
Thermistor ships with its wire harness included
High-limit thermostat resets automatically after tripping — no replacement needed after each trip
Direct drop-in replacement for both original components
Replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, and PS16732335
Compatible with LG and select Kenmore and GE-branded LG-built dryers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
AGM30045804
Part Type
Dryer High-Limit Thermostat and Thermistor Kit
Condition
Genuine OEM
Brand
LG
Kit Contents
High-limit thermostat + thermistor with wire harness
Thermistor Location
Blower housing
High-Limit Thermostat Type
Automatically resetting
Repair Difficulty
Easy to Moderate — 30 to 60 minutes
Compatible Brands
LG, select Kenmore, GE (LG-built models)
Installation Notes
⚠️ Unplug Dryer Before Starting — Let It Cool Fully First Disconnect power at the outlet or shut off the circuit breaker before beginning, and allow the dryer to cool completely if it was recently run. Wear work gloves. Access on many LG models follows this general sequence: remove the lint screen, then remove the two front panel screws underneath it, the two screws on the face of the panel, and the two screws holding the blower cover in place. Disconnect the door switch connector and remove the front panel. With the front open, release the drive belt from the tensioner and remove the drum to access the blower housing where the thermistor is located. Photograph the wiring connections before disconnecting anything, since the thermistor and high-limit thermostat can be easy to confuse with other similar-looking components nearby. Disconnect and remove the old thermistor and high-limit thermostat, noting their exact mounting positions. Install the new components from this kit in the same positions, reconnecting wiring exactly as photographed. Reinstall the drum, re-tension the belt over the tensioner, and reassemble the front panel, blower cover, and lint screen area in reverse order. Restore power and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips screwdriver, nut driver, work gloves.
Frequently Asked Questions
I already replaced the high-limit thermostat, but it keeps tripping. Why would I need this kit instead?
This is a well-documented pattern. If the thermistor — the sensor that reports temperature to the control board — is misreading heat, the control can keep driving the heating element past the point where the high-limit thermostat has to trip repeatedly to protect the dryer, even with a brand-new thermostat installed. Replacing the thermistor alongside the thermostat addresses the root cause rather than just the symptom, which is exactly why LG packages them together as one kit.
What's the difference between the thermistor and the high-limit thermostat?
The thermistor is a sensor, not a switch — it's a variable resistor whose resistance changes with temperature, and the control board reads that value continuously to regulate heat output throughout the cycle. The high-limit thermostat is a safety switch that does one job: it shuts off the heating element automatically if temperature exceeds a safe limit, then resets itself once things cool down. A failing thermistor causes inconsistent or inaccurate heat regulation; a failing high-limit thermostat causes the dryer to shut off unexpectedly or fail to protect against overheating.
My parts diagram shows more thermostat-like parts than what's in this kit. Did I order the wrong thing?
Not necessarily — some LG dryer models have additional related components, such as a separate blower thermostat, that are not part of this specific kit. This kit covers the high-limit thermostat and thermistor. If your repair calls for additional related parts, or if you're not sure exactly which components your model needs, contact our support team with your model number and we'll help you confirm the complete parts list before you order.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It includes the same resistance values, switch threshold, and wire harness configuration as the high-limit thermostat and thermistor originally installed in your dryer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
