Search results for "dishwasher thermostat"

5304517587 Dishwasher Switch Assembly Description:  The Switch Assembly is an OEM replacement part for specific Frigidaire dishwasher models. It contains a touchpad and electronic controls that operate wash cycles and drying features.  Replaces Part Numbers:5304517587, 4840235, AP6802340, PS12585690.  California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WPW10165425 Refrigerator Genuine Defrost Thermostat Replaces Part Numbers: WPW10165425, W10165425, 126393249SP, 12639324SP, 1455131, OEM24064262, AP6016065, PS11749348. Description: This Bimetal Defrost Thermostat is a Genuine OEM part for select Whirlpool refrigerator models. It plays a vital role in the defrost system, regulating the freezer temperature to prevent excessive frost buildup. The thermostat serves as a safety device by shutting off power to the defrost heater if the temperature gets too high, thereby protecting the appliance from overheating and potential damage.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WD21X25468 Genuine OEM GE Dishwasher Pressure Sensor Assembly The WD21X25468 is a Genuine OEM GE replacement dishwasher pressure sensor assembly compatible with a wide range of GE, GE Profile, GE Café, Hotpoint, Haier, and Monogram dishwashers in the GDF, GDT, GDP, PDT, CDT, ZDT, QDP, and HDF series. The pressure sensor monitors water pressure inside the dishwasher tub during fill and drain cycles and sends real-time readings to the electronic control board. The control board uses these readings to calculate the correct amount of water needed for each wash cycle and to confirm that the tub has drained properly before advancing to the next cycle phase. When the pressure sensor fails — or when it becomes clogged with grease, food residue, or mineral buildup — the dishwasher may not fill with water, may overfill, may stop mid-cycle, may fail to drain correctly, or may display error codes H2O or FTD (Failure to Drain). This Genuine OEM part is manufactured by GE to factory specifications. It directly replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, and 265D3356P001. Sold individually. Installs in 15–20 minutes — a screwdriver is the only tool required for most models. Quick Answer The WD21X25468 Genuine OEM GE Dishwasher Pressure Sensor Assembly fixes GE dishwashers displaying error codes H2O or FTD (Failure to Drain), not filling with water, overfilling, stopping mid-cycle, or running excessive noise from the spray arms. Monitors water level and pressure — signals the control board to fill, wash, and drain correctly. Genuine OEM. Replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, 265D3356P001. Sold individually. Compatible with GE GDF, GDT, PDT, CDT, ZDT, QDP, HDF, and related series. Common Problems This Part Fixes Error code H2O displayed — dishwasher not receiving enough water or no water at all Error code FTD (Failure to Drain) displayed — sensor not confirming tub has drained Dishwasher not filling with water when a cycle is started Dishwasher overfilling — sensor not signaling the control board to stop filling Dishwasher stopping mid-cycle without completing the wash Excessive noise during operation — sensor not accurately controlling spray arm water pressure Dishwasher requires priming with water to start (filling the tub manually before it will run) Replaces Part Numbers This pressure sensor directly replaces the following OEM and cross-reference part numbers: WD21X25468, 265D3356P001, AGE24772, AP6976524, EAP12741258, PD00067609, PS12741258. Contact our support team with your model number if you need confirmation before ordering. Compatibility This pressure sensor is compatible with a wide range of dishwashers from the following GE product lines: GE dishwashers — GDF450, GDF510, GDF511, GDF535, GDF550, GDF565, GDF570, GDF630, GDF640, GDF645 series GE dishwashers — GDT530, GDT535, GDT565, GDT580, GDT605, GDT625, GDT630, GDT635, GDT645, GDT695 series GE dishwashers — GDP615, GDP645, GDP665 series GE Profile dishwashers — PDT715, PDT775, PDT785 series GE Café dishwashers — CDT800, CDT875 series GE Monogram dishwashers — ZDT800, ZDT870, ZDT925, ZDT985 series Hotpoint dishwashers — HDF310, HDF330 series Haier dishwashers (select GE-platform models) GE / Café / Profile — QDP555 series Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Monitors water pressure inside the tub throughout fill and drain cycles — signals the control board to fill to the correct level and confirm complete drainage Resolves H2O and FTD error codes on compatible GE dishwashers Sensor can also fail due to grease or mineral buildup blocking the pressure port — cleaning may resolve the issue without replacement Replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, and 265D3356P001 Compatible with GE GDF, GDT, GDP, PDT, CDT, ZDT, QDP, HDF, and Hotpoint dishwasher series Sold individually Quick DIY repair — installs in 15–20 minutes with a screwdriver Product Specifications Part Number WD21X25468 Part Type Dishwasher Pressure Sensor Assembly (Pressure Switch) Condition Genuine OEM Application GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier Dishwashers Function Monitors tub water level and pressure — signals control board for fill and drain control Error Codes Resolved H2O (no/low water), FTD (Failure to Drain) Sold As Single sensor assembly Compatible Brands GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting Disconnect power and shut off the water supply before beginning. On most compatible GE models, the pressure sensor is located near the bottom of the dishwasher tub, accessible after removing the lower front kick panel (secured by one or two screws). The sensor assembly connects to a small hose and a wiring harness connector. Tip: before replacing the sensor, remove it and inspect the pressure port and hose for grease, food residue, or mineral buildup — a clogged sensor port can cause H2O and FTD errors without the sensor itself being electrically failed. Clean the port and hose with warm water and a small brush, reinstall, and test the dishwasher. If the error codes persist after cleaning, replace the WD21X25468 sensor. To replace: disconnect the hose and wiring harness from the old sensor, unclip or unscrew the sensor from its mounting bracket, and install the new sensor in the same position. Reconnect the hose and harness, restore power and water, and run a test cycle. Tools needed: Phillips screwdriver. Frequently Asked Questions What does the dishwasher pressure sensor do? The pressure sensor monitors the water pressure — and therefore the water level — inside the dishwasher tub throughout the wash cycle. It sends continuous readings to the electronic control board, which uses the data to determine how much water to add during fill, when to stop filling, and whether the tub has drained completely before advancing to the next cycle phase. An accurate pressure sensor is essential for the dishwasher to fill to the correct level (not too much, not too little), wash with the correct spray arm pressure, and drain fully before moving on to rinse or dry cycles. What do error codes H2O and FTD mean on GE dishwashers? H2O error code on compatible GE dishwashers indicates that the dishwasher is not detecting enough water in the tub — either water is not filling at all, or the pressure sensor is not sensing the water that has filled. FTD (Failure to Drain) code indicates the dishwasher has not confirmed that the tub has drained within the expected time. Both codes can be caused by a faulty pressure sensor, a clogged sensor port, a failed fill valve, a blocked drain system, or control board issues. The pressure sensor should be inspected and tested first since it is the most accessible and commonly replaced component for these two error codes. Should I try cleaning the sensor before replacing it? Yes — absolutely. The pressure sensor on GE dishwashers can produce H2O and FTD error codes when its pressure port or connected hose becomes clogged with grease, food residue, or hard water mineral deposits — even if the sensor itself is electrically intact. Before ordering a replacement, remove the sensor, inspect the pressure port opening, and clean it thoroughly with warm water and a small brush. Flush the connected hose to clear any buildup. Reinstall and run a test cycle. If the error codes return, the sensor has electrically failed and needs replacement with the WD21X25468. My dishwasher won't fill unless I pour water in manually first — is this the pressure sensor? Yes — this is a classic symptom of a clogged or failed pressure sensor. When the sensor port is blocked, the sensor reads zero pressure (empty tub) even when the dishwasher starts. In some cases the control board interprets this as a drainage confirmation and will not initiate the fill cycle. Pouring water into the filter manually raises the physical water level enough to trigger filling. Check and clean the sensor port as described above. If cleaning does not resolve the issue, replace the WD21X25468 sensor. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same pressure sensor assembly installed in compatible GE, GE Profile, GE Café, Hotpoint, and related brand dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WD15X26078 Genuine OEM GE Dishwasher Water Inlet Valve The WD15X26078 is a Genuine OEM GE replacement dishwasher water inlet valve compatible with a wide range of GE, GE Profile, Café, Haier, Hotpoint, RCA, and Kenmore GE-built dishwashers. The water inlet valve is mounted at the base of the dishwasher behind the lower access panel, connecting the household water supply line to the dishwasher's fill circuit. When the control board calls for water during the fill phase, the valve's internal solenoid opens, allowing water to flow into the tub — and it closes the instant the call is dropped, stopping flow precisely at the correct fill level. Without a properly functioning inlet valve, the dishwasher can't fill correctly — leading to poor cleaning performance, error codes, or no wash at all. Rated 120V, 60Hz. Approximate dimensions: 3.75" H x 3.25" W x 3.00" L. Silver/multi-color metal and plastic construction with a deep-threaded, high-quality water inlet for a tight supply-line connection and a secure outlet design that keeps the internal fill hose firmly attached. As a Genuine OEM part manufactured by GE to factory specifications, the WD15X26078 directly replaces 4959029, AP6986683, PS16217027, EAP16217027, and PD00064270. Hard water sediment is a leading cause of inlet valve clogging and failure on GE dishwashers — if your old valve is restricted by mineral buildup, replacement (not cleaning) is the recommended fix, as the internal components are easily damaged during cleaning attempts. Installs in 20–30 minutes with basic hand tools. Quick Answer The WD15X26078 Genuine OEM GE Dishwasher Water Inlet Valve fixes GE, GE Profile, Café, Haier, Hotpoint, and Kenmore dishwashers that aren't filling with water, fill slowly, display the H2O error code, make strange noises or vibration during fill, won't stop filling, or leak from the valve area. 120V, 60Hz. Approx 3.75"H x 3.25"W x 3.00"L. Genuine OEM GE. Replaces 4959029, AP6986683, PS16217027, EAP16217027, PD00064270. Compatible with GDF, GDT, GDP, PDT, PDP, QDP, ZDT, DDT, and Café CDT series dishwashers. Common Problems This Part Fixes Dishwasher not filling with water at all — valve solenoid not opening Dishwasher filling slowly or not getting enough water — valve clogged with hard water sediment H2O error code displayed — insufficient water intake detected Strange noises or vibration during the fill phase — worn valve diaphragm Dishwasher won't stop filling — valve stuck open (overfill/flood risk) Water leaking from the valve area or its connections Dishes not being cleaned properly due to insufficient water fill Wash cycle interrupted or extended due to fill timeouts Valve inlet screen visibly clogged with mineral deposits Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers: WD15X26078, AGE846049, AP6986683, EAP16217027, PD00064270, PS16217027 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: some similar-looking GE valves (such as WD15X24213 or WD15X26140) are different parts — verify your original valve's part number or your dishwasher model number before ordering. Compatibility This water inlet valve is compatible with select dishwashers from the following brands: GE dishwashers — GDF series (GDF510PGM4BB/WW, GDF510PSM4SS/5SS, GDF511PSM5SS, GDF511PGM5WW, GDF530PGM4BB/CC/WW/5WW, GDF530PSM4SS/5SS, GDF530PMM4ES, GDF565SSN3SS, GDF630PFM4DS/5DS, GDF630PGM4BB/WW/5BB, GDF630PMM4ES/5ES, GDF630PSM4SS, GDF640HFM4DS, GDF640HGM4WW/5BB, GDF640HMM4ES, GDF645SGN2BB/WW/3BB/3WW, GDF645SMN2ES/3ES, GDF645SSN2SS/3SS and related) GE dishwashers — GDT series (GDT530PGP5BB, GDT530PSP5SS, GDT535PSMASS, GDT535PSM5SS, GDT565SSN2SS, GDT605PSM5SS, GDT630PFM4DS, GDT630PMM4ES/5ES, GDT630PYM4FS, GDT635HMM4ES, GDT635HSM4SS/5SS, GDT645SGN2BB/WW/3WW, GDT645SMN3ES, GDT645SSN2SS, GDT645SYN2FS, GDT665SBN2TS/3TS, GDT665SFN3DS, GDT665SGN2WW/3WW, GDT665SMN2ES, GDT665SSN3SS and related) GE dishwashers — GDP series (GDP615HFM4DS, GDP645SYN3FS/4FS/8FS, GDP665SYN2FS/3FS/4FS/8F7S and related) GE Profile dishwashers — PDT series (PDT715SBN2TS/3TS, PDT715SFN3DS, PDT715SMN2ES/3ES, PDT715SYN3FS, PDT775SYN2FS/3FS, PDT785SBN2TS, PDT785SYN2FS/3FS/5FS and related) GE Profile dishwashers — PDP series (PDP715SBN3TS, PDP715SYN3FS and related) GE dishwashers — QDP series (QDP555SBN4TS, QDP555SYN4FS and related) GE Monogram dishwashers — ZDT series (ZDT925SIN2II/3II/5II, ZDT925SPN2SS/3SS, ZDT925SSN2SS/3SS/5SS, ZDT985SIN3II, ZDT985SPN5SS, ZDT985SSN5SS and related) GE dishwashers — DDT series (DDT700SBN2TS/3TS, DDT700SFN2DS/3DS, DDT700SGN2BB/WW, DDT700SMN2ES and related) Café dishwashers — CDT series (CDT800P2N2S1-N5S1, CDT805M5N2S5-N4S5, CDT805P2N2S1-N5S1, CDT845M5N2S5-N5S5, CDT845P2N2S1-N5S1, CDT845P3N2D1-N5D1, CDT845P4N2W2-N5W2, CDT855M5N2S5/N3S5/N5S5, CDT855P2N2S1/N3S1/N5S1, CDT875M5N2S5-N7S5, CDT875P2N2S1-N5S1, CDT875P3N5D1 and related) Haier dishwashers (select models using the GE-platform valve) Hotpoint and RCA dishwashers (select GE-built models) Kenmore / Sears dishwashers (select GE-built models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Controls the flow of water into the dishwasher during fill cycles — precise fill for optimal cleaning performance Solenoid-actuated — opens when the control board calls for water and closes the moment the call is dropped Rated 120V, 60Hz — correct electrical specifications for compatible GE-platform dishwashers Approximate dimensions: 3.75" H x 3.25" W x 3.00" L Deep-threaded water inlet for a tight, leak-free supply line connection Secure outlet design keeps the internal fill hose firmly attached Resolves H2O error codes, no-fill, slow-fill, overfill, and fill-noise symptoms Replaces 4959029, AP6986683, PS16217027, EAP16217027, and PD00064270 Compatible with GE GDF/GDT/GDP series, GE Profile PDT/PDP series, QDP series, Monogram ZDT series, DDT series, Café CDT series, plus Haier, Hotpoint, RCA, and Kenmore GE-built dishwashers DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WD15X26078 Part Type Dishwasher Water Inlet Valve Assembly Condition Genuine OEM Application Dishwashers (GE platform) Voltage 120V AC Frequency 60 Hz Dimensions Approximately 3.75" H x 3.25" W x 3.00" L Color Silver / Multiple Colors Material Metal / Plastic Error Codes Resolved H2O (insufficient water intake) Compatible Brands GE, GE Profile, Café, Monogram, Haier, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power at the breaker and shut off the household water supply at the shutoff valve under the sink before beginning. Wear work gloves to protect your hands. Have towels and a shallow dish ready — residual water remains in the supply line and hoses and will spill when disconnected. Remove the lower access panel (baffle) at the front bottom of the dishwasher — typically 2–4 screws. Locate the water inlet valve where the household supply line enters the dishwasher. Photograph the hose and wire connections before disconnecting anything. Disconnect the household water supply line from the valve inlet (use pliers for the larger ingress connection — place the dish underneath to catch leftover water). Disconnect the internal fill hose from the valve outlet (needle-nose pliers help with the smaller egress hose clamp). Unplug the electrical connector that snaps onto the valve solenoid. Remove the mounting screws holding the valve bracket to the frame and lift the old valve out. Install the new WD15X26078 valve in the same position, secure the mounting screws, reconnect the internal fill hose with its clamp, and snap the electrical connector back on. Reconnect the household water supply line to the valve inlet — align the threads carefully and tighten snugly without over-torquing. Turn the water supply back on and use a flashlight to inspect all connections for leaks BEFORE reinstalling the access panel. Restore power and run a test cycle to confirm proper filling with no leaks. Tools needed: Phillips screwdriver, pliers, needle-nose pliers, shallow dish, towels, flashlight, work gloves. Frequently Asked Questions What does the H2O error code mean on my GE dishwasher? The H2O error code on GE dishwashers indicates the control board is not detecting sufficient water intake during the fill phase. Common causes are: a failed or clogged water inlet valve (the most frequent culprit), the household water supply shutoff valve partially closed, a kinked supply line, or low household water pressure. First verify the supply valve under the sink is fully open and the line isn't kinked. If the supply checks out, the WD15X26078 inlet valve is the standard fix — hard water sediment gradually clogs the valve's internal screen and passages, restricting flow until the dishwasher can't fill within its expected time window. Can I clean the old valve instead of replacing it? It's not recommended. While the inlet screen on some valves can be carefully brushed clean, the internal passages and solenoid diaphragm of a sediment-clogged valve are easily damaged during cleaning attempts — a common outcome is a valve that leaks or sticks open after being "cleaned," which risks flooding. Real-world experience (including customer stories with this exact part) shows that attempting to clean a hard-water-clogged valve often breaks it. Given the moderate cost of the OEM replacement versus the flood risk of a compromised valve, replacement is the reliable repair. If your area has hard water, consider this a maintenance item that may need periodic replacement. My dishwasher won't stop filling — is that also this valve? Yes — a valve stuck in the open position is the other failure mode. When sediment or a worn diaphragm prevents the valve from sealing fully closed, water continues to flow into the tub even when the control board has cut power to the solenoid. This can lead to overfilling and potentially flooding through the door or float overflow. If your dishwasher keeps filling past its normal level, or you find water accumulating in the tub between cycles, shut off the water supply at the sink immediately and replace the valve before running the dishwasher again. How do I know this is the right valve for my GE dishwasher? Check your dishwasher's model number (on a label along the door frame or tub edge) against the compatibility list above — the WD15X26078 covers a broad range of GE GDF, GDT, GDP, Profile PDT/PDP, QDP, Monogram ZDT, DDT, and Café CDT series dishwashers. Be aware that some similar-looking GE valves (such as WD15X24213 or WD15X26140) are different parts used on other model groups — they are not interchangeable with the WD15X26078. If your model isn't in the list or your original valve shows a different part number, contact our support team with your model number and we'll verify the correct valve before you order. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same water inlet valve installed in compatible GE, GE Profile, Café, Monogram, Haier, Hotpoint, RCA, and Kenmore GE-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WD08X10057 Dishwasher Door Gasket 📝 Product Description Stop leaks and restore a tight door seal with the XPARTCO WD08X10057 Dishwasher Door Gasket. This Dishwasher Door Gasket is a replacement Part designed for specific GE, Hotpoint dishwasher models. This part is crucial as it seals the gap between the dishwasher tub's opening and the outer edge of the door. The gasket prevents water leakage during operation. With a length of 89 inches and a width of one-sixteenth of an inch, this door gasket is a perfect fit for models that it's designed for. It's an ideal replacement for old gaskets that are cracked, torn, or shrunken. ⚡ Quick Answer If your dishwasher is leaking from the door or you notice moisture around the front, the WD08X10057 door gasket may be worn or damaged. Replacing it restores a proper seal and prevents leaks. 🔄 Replaces Part Numbers Replaces OEM part number: WD08X10057, 1088473, WD08X10014, WD8X10014, AGE24065, EAP958908, PD00001117, AP3798079, PS958908. 🔧 Compatibility This dishwasher door gasket is compatible with many GE, Hotpoint, and other GE-manufactured dishwashers. ✔️ GE Dishwashers ✔️ Hotpoint Dishwashers ✔️ GE Profile Dishwashers Always verify your appliance model number before ordering to ensure proper fit. 🛠️ Common Problems This Part Fixes ❌ Water leaking from dishwasher door ❌ Moisture buildup around door seal ❌ Poor sealing causing inefficient washing ❌ Cracked, brittle, or worn gasket ✨ Key Features ✔️ Designed for GE dishwasher compatibility ✔️ Creates a tight, leak-proof door seal ✔️ High-quality flexible rubber construction ✔️ Easy to install replacement 📊 Product Specification Part Number: WD08X10057 Part Type: Dishwasher Door Gasket Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Material: Flexible Rubber ⏳ When Should You Replace This Gasket? Replace the gasket if you notice water leaking from the door, visible cracks, stiffness, or if the seal no longer fits snugly. ⚠️ Installation Notes ⚠️ Disconnect power before installation. Remove the old gasket from the channel and press the new gasket evenly into place around the door frame. ❓ Frequently Asked Questions 🔹 Will this gasket fit my dishwasher?This gasket fits many GE and compatible dishwashers. Always verify your model number. 🔹 What does a dishwasher door gasket do?It seals the dishwasher door to prevent water from leaking during operation. 🔹 What are signs of a bad gasket?Water leaking, cracks, stiffness, or improper sealing are common signs. 🔹 Is installation difficult?No, most installations are simple and require no special tools. 🛒 Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality aftermarket parts. We offer fast shipping, reliable products, and expert support. ✔️ Fast Shipping✔️ Quality Tested Parts✔️ Compatibility Support

Read more less

W11126005CM Dishwasher Wash Vane Sensor Description: This Sensor is a replacement component specifically designed for certain Whirlpool dishwasher models. It plays a crucial role in monitoring cycle conditions like temperature and soil levels to automatically customize wash sequences. Causes of a bad sensor can include leaking or faulty wiring disrupting signals over time, mineral buildup gumming internal mechanisms, or damage from impact. Replaces Part Numbers: W11126005, W11503875, W10380177, W10380483, W10647239, AP6261394, PS12114437. This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: California’s Proposition 65 

Read more less

W11414076 Genuine OEM Whirlpool Dishwasher Circulation Pump Motor Assembly The W11414076 is a Genuine OEM Whirlpool replacement circulation pump and motor assembly compatible with a wide range of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea dishwashers. The circulation pump is the heart of the wash system — it pressurizes and delivers water to the spray arms, driving the jets that blast food and residue off your dishes throughout the wash and rinse cycles. When the circulation pump fails, cleaning performance collapses: dishes come out dirty or unrinsed, water pressure at the spray arms drops, and the machine may make loud droning or grinding noises. This is a complete circulation pump and motor assembly. Common causes of failure include worn motor bearings (which produce a continuous drone that gets louder over time), deteriorated impellers, and seal breakdowns. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W11414076 is the current production part that supersedes W11122133. It also replaces AP6980104, EAP12745416, PS12745416, 4958907, and OEM20940317. Note: this assembly does not include the drain pump — your existing drain pump transfers over to the new assembly during installation. Installs in 45–90 minutes with basic hand tools (the dishwasher must be pulled out and laid on its back to access the pump). Quick Answer The W11414076 Genuine OEM Whirlpool Dishwasher Circulation Pump Motor Assembly fixes Whirlpool, KitchenAid, Maytag, Jenn-Air, and Amana dishwashers where dishes come out dirty or unrinsed, water pressure at the spray arms is weak, water pools in the tub, or the motor makes a loud droning/grinding noise. Complete circulation pump + motor assembly. Genuine OEM. Current part superseding W11122133; also replaces AP6980104, EAP12745416, PS12745416, 4958907, OEM20940317. Before ordering: if the motor runs but water is weak, try cleaning the impeller filter screen first — see the FAQ. Common Problems This Part Fixes Dishes coming out dirty or unrinsed — circulation pump not delivering water to the spray arms Weak water pressure at the spray arms — impeller worn or motor failing Loud droning noise that gets louder over time — worn motor bearings Grinding or unusual noise during operation Water retention/pooling in the bottom of the tub Leaks from the pump housing — seal breakdown Motor humming but spray arms barely turning Reduced cleaning performance overall Motor not running at all — failed pump motor windings Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This circulation pump motor assembly directly replaces the following OEM and cross-reference part numbers: W11414076, W11122133, AP6980104, EAP12745416, PS12745416, 4958907, OEM20940321, AWP45352, PD00070783 W11414076 is the current OEM production part superseding W11122133. Contact our support team with your model number if you need confirmation before ordering. Compatibility This circulation pump motor assembly is compatible with select dishwashers from the following brands: Whirlpool dishwashers — select models (verify with your parts diagram) KitchenAid dishwashers — select models Maytag dishwashers — select models Jenn-Air dishwashers — select models Amana dishwashers — select models Magic Chef dishwashers — select models Admiral dishwashers — select models Norge dishwashers — select models Roper dishwashers — select models Kenmore / Sears dishwashers — select Whirlpool-built models Ikea dishwashers — select Whirlpool-built models This assembly may comprise several parts — refer to your specific parts diagram to verify included items. Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Circulation pump and motor assembly — pressurizes and delivers water to the spray arms for effective cleaning and rinsing Resolves "dirty dishes," "weak water pressure," "loud droning motor," "grinding noise," and "water pooling" symptoms when caused by pump failure Addresses the common failure modes: worn motor bearings, deteriorated impellers, and seal breakdowns Current OEM production part — directly supersedes W11122133 Also replaces AP6980104, EAP12745416, PS12745416, 4958907, and OEM20940317 Motor separates from the pump case with 3 Torx screws — some customers replace only the motor if the pump case is fine Drain pump is not included — your existing drain pump transfers to the new assembly Compatible with Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea dishwashers DIY repair — installs in 45–90 minutes with basic hand tools Product Specifications Part Number W11414076 Supersedes W11122133 Part Type Dishwasher Circulation Pump & Motor Assembly Condition Genuine OEM Application Dishwashers (Whirlpool platform) Function Delivers water to the spray arms for washing and rinsing Motor Attachment Separates from pump case with 3 Torx screws Drain Pump Not included — transfer your existing drain pump Location Bottom of dishwasher (access by laying unit on its back) Compatible Brands Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, Ikea Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Wear Work Gloves — Major Access Required Disconnect power at the breaker and shut off the water supply before beginning. Wear work gloves to protect your hands. This is a more involved repair because the circulation pump is on the bottom of the dishwasher. Throw the circuit breaker, remove the lower access panel, and open the electrical box to completely disconnect the electrical from the dishwasher. Disconnect the water supply line and the drain line. Remove the anchor screws securing the dishwasher to the counter, then pull the dishwasher out of the cabinet. Have a large towel ready — rotate the dishwasher and lay it on its back to access the pump on the bottom. Photograph everything before disconnecting. Disconnect all connections to the main circulation pump: the drain pump, the electrical connections, the leak-detection plate and circuit, and the water lines. Undo all clamps to the circulation pump. Remove the old circulation pump assembly. Transfer your existing drain pump to the new W11414076 assembly — it is not included. (If you're only replacing a noisy motor and the pump case is good, the motor separates from the case with 3 Torx screws and can be swapped on its own.) Install the new assembly, reconnect the drain pump, electrical connections, leak-detection plate, water lines, and all clamps, matching your photos. Stand the dishwasher back up, slide it into the cabinet, reconnect water/drain/electrical, and secure the anchor screws. Run a short test cycle and check for leaks. Note: use your dishwasher's onboard diagnostic function to confirm the pump was the issue — light/error codes vary by model, so check the quick guide that came with your specific dishwasher rather than relying on codes listed online for other models. Tools needed: Phillips screwdriver, Torx driver (T-set), nut driver, pliers, large towel, work gloves. Frequently Asked Questions The motor runs but water barely reaches the spray arms — do I definitely need a new pump? Maybe not — try this first, because it could save you the entire repair. On many KitchenAid/Whirlpool-platform dishwashers, there's a fine filter screen INSIDE the circulation pump on the impeller. This screen can clog with microplastics and fine food particles over time (sometimes after a surprisingly small number of wash cycles), which chokes off water flow even though the motor is running perfectly. The screen can look clean but still be blocked — a real-world test is to hold water in the mesh cup: if it holds water like a cup instead of draining freely, it's clogged. Cleaning it with a toothbrush restores full flow. To access it you do have to pull the pump (the same disassembly as replacing it, then 2 Torx screws to open the pump), so if you're already this far in, disassemble and inspect the screen BEFORE installing a new pump — you may find the old pump is perfectly good. Running a dishwasher-safe cleaning product through the machine first is also worth a try. My dishwasher motor is loud and getting louder — is that the pump? Yes, that's a classic sign of worn circulation pump motor bearings. The motor bearings wear out over time, and as they degrade they produce a continuous drone that steadily gets louder. Once the bearings have failed, the noise won't go away on its own and the motor should be replaced. On this assembly, the motor separates from the pump case with 3 Torx screws — some customers who only have a bearing/noise problem (and an otherwise good pump case) simply swap the motor and reuse the case. If you order the full assembly, you get both, and you can decide during the repair whether to swap just the motor or the whole thing. Does this come with the drain pump? No — the W11414076 is the circulation pump and motor assembly, and it does not include the drain pump. During installation, you'll transfer your existing drain pump from the old assembly to the new one (it detaches and reattaches). This is normal for this repair. If your drain pump is also failing (separate symptoms: won't drain, water left standing after the cycle), that's a different part you'd order separately. The circulation pump handles washing/spray pressure; the drain pump handles emptying the tub. What's the difference between W11414076 and W11122133? These are the same circulation pump assembly across production revisions. W11122133 was the earlier OEM part number, and W11414076 is the current production version that Whirlpool issued as its direct replacement. Both are physically and functionally interchangeable — if your dishwasher's parts diagram shows W11122133, the W11414076 is the correct current replacement, and this listing covers both. The cross-references AP6980104, PS12745416, and 4958907 are additional catalog identifiers for the same part. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same circulation pump and motor assembly installed in compatible Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, and Kenmore Whirlpool-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WD26X25103 Genuine OEM GE Dishwasher Variable Wash Pump Kit The WD26X25103 is a genuine GE OEM variable wash pump kit for premium GE, Café, GE Profile, Monogram, Hotpoint, and Haier dishwashers. The wash pump is the heart of the cleaning system — it draws filtered water from the sump and drives it under pressure through the lower spray arm, the middle spray arm, and the upper wash manifold. What makes this a variable pump is its variable-speed motor: instead of running at one fixed speed, the control board modulates pump speed throughout the cycle, ramping pressure up for heavy soil and down for delicate loads, and shifting flow between spray zones. That is why a failing variable pump often produces uneven results — the bottom rack comes out clean while the top rack is barely wet. This is a complete kit, supplied with the circulation pump assembly and its integrated wiring harness, so you are not transferring connectors from the old unit. Typical failure modes include worn motor bearings that produce a loud humming or grinding during the wash portion of the cycle, a seized or debris-jammed impeller, a shaft seal that begins weeping water into the base pan and trips the flood switch, and electrical failure of the variable-speed motor windings. It directly replaces WD26X22789, AP6973120, PS12730515, and EAP12730515. This is a moderate DIY repair — most people budget 1–2 hours. Quick Answer The WD26X25103 Genuine OEM GE Variable Wash Pump Kit fixes GE, Café, GE Profile, Monogram, Hotpoint, and Haier dishwashers with dishes that come out dirty or gritty, a top rack that isn't getting wet, weak or no spray arm rotation, loud humming or grinding during the wash cycle, or water pooling in the base pan from a leaking pump seal. Variable-speed motor; kit includes pump assembly plus integrated wiring harness. Replaces WD26X22789, AP6973120, PS12730515, EAP12730515. Fits premium CDT865/CDT866, PDT845/PDT846/PDT855, and ZDT915/ZDT975 platforms — not the same pump as WD26X23258. Common Problems This Part Fixes Dishes not getting clean — food soil, grit, or film left behind after a full cycle Top rack not getting wet or not getting cleaned while the bottom rack washes normally Spray arms turning slowly or not turning at all — insufficient water pressure Loud humming, whining, or grinding noise during the wash portion of the cycle Dishwasher runs a full cycle quietly with no audible water circulation Water pooling in the base pan under the dishwasher from a leaking pump shaft seal Flood switch or leak sensor tripping and shutting the dishwasher down mid-cycle Cleaning performance that has gradually declined over months as bearings wear Pump motor humming but the impeller not turning — seized shaft or jammed impeller Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher variable wash pump kit directly replaces the following OEM and cross-reference part numbers: WD26X25103, WD26X22789, AGE25305, AP6973120, PD00054224, PS12730515, EAP12730515. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This variable wash pump kit is compatible with select premium built-in dishwashers from the following brands: GE and GE Profile dishwashers (PDT845, PDT846, and PDT855 series) Café dishwashers (CDT865 and CDT866 series) Monogram dishwashers (ZDT915 and ZDT975 series) Hotpoint dishwashers (select GE-built models) Haier dishwashers (select GE-platform models) Verified model numbers include: CDT865SSJ0SS, CDT865SSJ2SS, CDT865SMJ0DS, CDT865SMJ2DS, CDT866P2M4S1, CDT866P3M4D1, CDT866P4M4W2, PDT845SSJ0SS, PDT845SSJ2SS, PDT845SMJ0ES, PDT845SMJ2ES, PDT845SBL2TS, PDT845SBL3TS, PDT845SFL3DS, PDT846SSJ0SS, PDT846SSJ2SS, PDT846SMJ0ES, PDT846SMJ2ES, PDT855SSJ0SS, PDT855SSJ2SS, PDT855SMJ0ES, PDT855SMJ2ES, PDT855SIJ0II, PDT855SIJ2II, PDT855SBL2TS, PDT855SBL3TS, PDT855SFL3DS, ZDT915SSJ0SS, ZDT915SSJ2SS, ZDT915SIJ0II, ZDT915SIJ2II, ZDT915SPJ0SS, ZDT915SPJ2SS, ZDT975SSJ0SS, ZDT975SSJ2SS, ZDT975SIJ0II, ZDT975SIJ2II, ZDT975SPJ0SS, and ZDT975SPJ2SS. Note: GE uses several different circulation pumps across its dishwasher lineup, and they are NOT interchangeable. The WD26X25103 is the variable-speed pump used on premium CDT/PDT/ZDT platforms. It is not the same part as the WD26X23258 circulation pump (GDT695/PDT825 platforms) or the WD26X22518 pump (PDF820/GDT535/ADT521 platforms). Fitting the wrong pump can result in a physical mismatch at the sump or a harness that will not mate with your control board. Always verify your full model number — including the suffix — before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified flow rate, impeller geometry, and motor control profile Variable-speed motor allows the control board to modulate wash pressure by cycle and soil level rather than running at one fixed speed Complete kit — includes the circulation pump assembly and integrated wiring harness, so no connectors need to be transferred from the old pump Drives water through the lower spray arm, middle spray arm, and upper wash manifold Resolves "dishes not clean," "top rack not getting wet," "spray arms not turning," "loud humming or grinding," and "water in the base pan" symptoms caused by pump failure Sealed shaft design protects the motor from sump water intrusion Direct drop-in replacement for the superseded WD26X22789 — no modifications required Serves GE Profile, Café, Monogram, Hotpoint, and Haier premium dishwasher platforms Replaces WD26X22789, AP6973120, PS12730515, and EAP12730515 Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WD26X25103 Part Type Dishwasher Variable Wash Pump Kit (Circulation Pump) Condition Genuine OEM Brand GE Appliances Motor Type Variable speed Voltage 120V / 60 Hz Function Circulates water under pressure to the spray arms and upper wash manifold Kit Contents Wash pump assembly + integrated wiring harness Location Underneath the tub, mounted to the sump housing Connections 2 hose clamps + 2 electrical connections Supersedes WD26X22789 Repair Difficulty Moderate — 1 to 2 hours Quantity 1 pump kit Compatible Brands GE, GE Profile, Café, Monogram, Hotpoint, Haier Installation Notes ⚠️ Disconnect Power And Shut Off Water Before Starting Turn off the dishwasher's circuit breaker and close the hot water supply valve under the sink before beginning. Wear work gloves — the tub edges and undercarriage brackets are sharp. Before condemning the pump, run a quick check: remove the lower spray arm and filter assembly, clear any glass chips, seeds, or labels from the sump, and confirm the spray arm ports are not blocked. A clogged filter screen produces the same "dishes not clean" complaint as a failing pump and costs nothing to rule out. To replace the pump, first remove the two screws securing the dishwasher to the underside of the countertop (or to the adjacent cabinets), disconnect the water line and drain hose, and slide the unit out. Most technicians then lay the dishwasher on its front or on its back to reach the pump — put a towel down to protect the door and finish. Photograph the hose routing and wiring before disconnecting anything. Release the two hose clamps and separate the two electrical connections, then unlock the pump from the sump housing — it typically twists to release from a bayonet-style mount — and lift it out. Inspect the sump gasket and seat while the pump is off; replace the gasket if it is hardened, flattened, or nicked. Install the new WD26X25103 in the same orientation, twist to lock, reattach both hoses with their clamps, and reconnect the harness. Reinstall the dishwasher, restore water and power, then run a full cycle and check underneath for leaks before pushing the unit all the way back and reattaching the mounting screws. Tools needed: Phillips screwdriver, nut driver, pliers or hose clamp pliers, towel, work gloves. Frequently Asked Questions My top rack isn't getting clean but the bottom rack is fine. Is that the wash pump? It's the signature symptom of a weakening wash pump, yes — but check two cheaper things first. The upper wash manifold and the middle spray arm are fed last and at the lowest pressure, so they are the first zones to suffer when pump output drops. However, a clogged filter screen or a spray arm with blocked ports will starve the upper rack the same way. Pull the lower spray arm and filter, rinse them under hot water, poke a toothpick through any blocked spray ports, and run a cycle. If the top rack is still dry or dirty after that, the variable pump is losing pressure and should be replaced. What does "variable" mean on this pump, and does it matter? It matters a great deal. A variable-speed pump lets the control board change pump speed during the cycle — higher pressure for heavy soil, lower for delicate loads, and different speeds when directing flow to different spray zones. A fixed-speed pump cannot do that. This is why you cannot substitute a standard circulation pump from another GE platform even if it physically resembles this one: the control board expects a variable-speed motor and will not drive a fixed-speed unit correctly. The dishwasher is making a loud grinding noise. Do I need the whole pump? Not always — check for foreign objects first. Glass chips, fruit pits, bones, and hard plastic bits routinely get past the filter and rattle inside the pump housing or wedge against the impeller. Remove the filter assembly and inspect the sump thoroughly with a flashlight. If the sump is clean and the noise is a steady hum or grind that rises with the wash cycle, the pump's motor bearings are worn and the complete kit is the correct repair. Bearing noise does not improve on its own and usually precedes a shaft seal leak. I found water in the pan underneath the dishwasher. Could the pump cause that? Yes. When the pump's shaft seal wears out, it weeps water down onto the base pan during every wash cycle. GE dishwashers have a flood switch in that pan, so the machine will eventually detect the water and shut itself down mid-cycle or refuse to start. Before ordering, confirm the water is coming from the pump and not from a loose hose clamp, a cracked sump, or the door gasket — dry the pan completely, run a short cycle, and watch where the first drops appear. Does this kit include everything, or do I need to reuse parts from the old pump? The kit ships with the wash pump assembly and its integrated wiring harness, so you will not need to cut, splice, or transfer the electrical connector from your old pump. You will reuse your existing hoses and clamps. Inspect the sump gasket while the pump is out and replace it if it looks hardened, flattened, or nicked — a tired gasket is a common cause of a "new pump that still leaks." What's the difference between WD26X25103 and WD26X22789? They are the same pump across production revisions. WD26X22789 was the earlier number and WD26X25103 is the current GE part number that supersedes it. If your dishwasher's parts diagram shows WD26X22789, this listing is the correct replacement — order it with confidence. The additional cross-references (AP6973120, PS12730515, EAP12730515) are catalog identifiers used by various parts distributors for the same kit. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original variable-speed motor profile, impeller geometry, flow rate, sump mounting interface, and harness connector of the pump originally installed in your dishwasher, which is important on this platform because the control board is calibrated to drive a variable-speed pump. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WR55X10025 Refrigerator Temperature Sensor The XPARTCO WR55X10025 is an aftermarket replacement refrigerator temperature sensor (thermistor) compatible with a wide range of GE, Hotpoint, Haier, Café, and Monogram refrigerators. The temperature sensor monitors air temperature inside the fresh food and freezer compartments and sends that data to the main control board, which uses it to regulate cooling cycles and maintain the correct set temperature. When the sensor fails, the refrigerator may run too warm, too cold, or experience erratic defrost behavior. This sensor measures approximately 1-1/4 inches long and includes 18-inch wire leads. It is constructed from white plastic and is used in both fresh food and freezer compartments depending on the model — on some models it also functions as a defrost sensor on the evaporator coil. It directly replaces OEM part numbers WR55X10025 and a large number of earlier GE thermistor part numbers. Sold individually — some models require two sensors. Installs in under 30 minutes with basic hand tools. Quick Answer The XPARTCO WR55X10025 Refrigerator Temperature Sensor fixes GE and Hotpoint refrigerators that are too warm, too cold, not defrosting, or over-defrosting. The thermistor monitors compartment temperature and communicates with the control board. Approx. 1-1/4" long with 18" leads, white plastic. Compatible with GE, Hotpoint, Haier, Café, and Monogram refrigerators. Sold individually. Common Problems This Part Fixes Refrigerator compartment running too warm — food spoiling faster than normal Refrigerator running too cold — food or liquids freezing in the fresh food section Freezer section not maintaining correct temperature Refrigerator not defrosting or defrosting too frequently Excessive frost or ice buildup on evaporator coils Refrigerator and freezer both warming up after extended defrost cycles Erratic cooling — temperatures fluctuating unpredictably Replaces Part Numbers This temperature sensor directly replaces the following OEM and cross-reference part numbers: WR55X10025, 914093, WR50X10027, WR50X10034, WR50X10055, WR50X10067, WR55X10025-50PK, WR55X10025B, WR55X10026, WR55X10027, WR55X10028, WR55X10030, WR55X10087, WR55X10088, WR55X10089, WR55X10367, WR55X10380, WR55X10661, WR55X10711, WR55X10735, WR55X10736, WR55X10737, WR55X10937, WR55X10938, WR55X10939, WR55X11121, WR55X11141, WR55X11151, WR55X11152, AH304103, EA304103, OEM9556230, AP3185407, EAP304103, AGE29661, PD00000992, PS304103 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This temperature sensor is compatible with select refrigerators from the following brands: GE refrigerators (side-by-side, French door, top-freezer, and bottom-freezer) Hotpoint refrigerators Haier refrigerators (select GE-platform models) Café refrigerators Monogram refrigerators Note: Some GE refrigerator models use two or more temperature sensors. This part is sold individually. Check your model's parts diagram or contact our support team to confirm how many sensors your model requires before ordering. Key Features Monitors fresh food and freezer compartment temperatures and communicates readings to the main control board Also functions as a defrost sensor on the evaporator coil on applicable models Fits both fresh food and freezer positions White plastic construction — durable and resistant to refrigerator temperature extremes Direct replacement for WR55X10025 and over 30 earlier GE thermistor part numbers Compatible with GE, Hotpoint, Haier, Café, and Monogram refrigerators Sold individually — verify quantity needed for your model before ordering Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in under 30 minutes with basic hand tools Product Specifications Part Number WR55X10025 Part Type Refrigerator Temperature Sensor (Thermistor) Condition Aftermarket Replacement Application Fresh food compartment, freezer compartment, and evaporator coil (defrost sensor) depending on model Sensor Body Length Approximately 1-1/4 inches Color White Material Plastic Includes Sensor with wire leads Sold As Single sensor (some models require 2 — verify before ordering) Compatible Brands GE, Hotpoint, Haier, Café, Monogram Installation Notes ⚠️ Unplug Refrigerator Before Starting Unplug the refrigerator from the power outlet before beginning any repair. To access the fresh food thermistor, locate the sensor on the left wall of the fresh food compartment — it may be clipped into a housing or bracket. Disconnect the wire connector and pull the old sensor out of its bracket. Slide the new WR55X10025 sensor into the bracket and reconnect the wire connector. To access the freezer or evaporator thermistor, remove the freezer shelves and back panel, then locate the sensor clipped to the evaporator coil bracket. Remove any tie wrap securing the sensor, pull the old sensor from the bracket, insert the new sensor, and reconnect the wire connector. Reinstall the back panel and shelves, restore power, and verify the refrigerator returns to the correct set temperature. Tools needed: Phillips screwdriver, flat pry tool (for panel clips), work gloves. Frequently Asked Questions How many temperature sensors does my GE refrigerator have? The number of sensors varies by model. Many GE French door and side-by-side refrigerators use two or three WR55X10025 sensors — one in the fresh food compartment, one in the freezer, and sometimes one on the evaporator coil. Check your model's parts diagram or contact our support team with your model number to confirm how many you need before ordering. What is a thermistor and how does it work? A thermistor is a type of resistor whose electrical resistance changes with temperature. The main control board sends a small voltage through the thermistor and measures the resistance — a higher resistance means a lower temperature, and a lower resistance means a higher temperature. The board uses this reading to decide when to run the compressor and fans to maintain the set temperature. A failed thermistor sends incorrect readings, causing the refrigerator to over-cool, under-cool, or malfunction during defrost cycles. Can a faulty temperature sensor cause the refrigerator to not defrost? Yes. On models where the WR55X10025 also serves as the defrost sensor on the evaporator coil, a faulty sensor can cause the control board to incorrectly time or skip defrost cycles entirely — leading to excessive frost or ice buildup on the evaporator coils. This frost buildup can eventually block airflow and cause both the refrigerator and freezer sections to warm up. How do I know if my temperature sensor is the cause of my cooling problem? The most reliable way to test the thermistor is with a multimeter. Disconnect the sensor and measure its resistance at room temperature — a working WR55X10025 should read approximately 16,000 ohms at 32°F, dropping as temperature increases. An open circuit (infinite resistance) or short circuit (zero resistance) reading confirms the sensor has failed. If resistance is within the normal range but the refrigerator still has issues, the control board or other components may be at fault. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from durable plastic to match the dimensions and performance specifications of the original WR55X10025 temperature sensor. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

DA32-00006W Genuine Samsung OEM Refrigerator Thermistor Refrigerator defrost temperature sensor. Replaces Part Numbers: DA32-10105R, DA32-00006W, DA32-00006U, 2030342, DA32-00006B, DA32-00006C, DA32-00006D, DA32-00006L, DA32-00006M, DA32-00006T, DA32-00006V, AP4135567, PS4138681. The Samsung Defrost Sensor is a genuine part designed specifically for Samsung refrigerators. This sensor, sometimes referred to as a defrost thermostat or defrost temperature sensor, is an integral part of your refrigerator's defrost system.  

Read more less

279769 Dryer Thermostat Kit - Compatible with Whirlpool, Kenmore, Maytag Product Description Keep your dryer running safely with the replacement 279769 Dryer Thermostat Kit. This kit is designed for select Whirlpool, Kenmore, Maytag, Roper, Estate, KitchenAid, and other dryers, featuring a high-limit thermostat (L250-80F) and a thermal cut-off fuse (352F) to prevent overheating. It addresses issues like no heat, not enough heat, overheating, or failure to start, offering a cost-effective alternative to OEM parts. Note: Includes one high-limit thermostat, one thermal cut-off fuse. Disconnect power before installation. Check dryer venting for blockages to prevent repeat failures. Replaces part numbers: 279769, 2004, 279548, 2796769, 279769VP, 2821, 3387812, 3389946, 3398671, 3977394, 695563, 80001, SET184, AH334278, EA334278, EAP334278, PD00002485, AP3094224, PS334278. Compatibility: Compatible with models including but not limited to: Whirlpool: NGD4655EW, WGD4815EW, WGD5000DW, MGDC215EW, MGDX655DW Kenmore: 110.60022010, 110.70102312, 110.78002012 Maytag: MEDC215EW1, MGDX655DW1 Roper: RED4640YQ0 Estate: EED4400WQ0 KitchenAid: YKEHS01PMT0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Estate, KitchenAid, and other dryers. 🔥 Specifications: High-limit thermostat (L250-80F), thermal cut-off fuse (352F). 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires screwdriver, pliers, work gloves; typically installed in 15–20 minutes. 🛡️ Effective Fixes: Resolves no heat, not enough heat, overheating, or failure to start. Product Specification Part Number: 279769 Component Type: Dryer thermostat kit Material: Metal and plastic Dimensions: High-limit thermostat: 2" L x 1-1/2" W; Thermal cut-off fuse: 2" L x 1-1/2" W (Based on web:6, web:16) Weight: 2.4 oz (Based on web:1, web:15) Electrical Specs: High-limit thermostat: L250-80F (121°C); Thermal cut-off fuse: 352F (178°C) Mounting: Screw-mounted on heater housing. Operating Conditions: Suitable for high-heat dryer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO DA32-10104N Refrigerator Temperature Sensor The XPARTCO DA32-10104N is an aftermarket replacement refrigerator temperature sensor (thermistor) compatible with select Samsung French door, side-by-side, and bottom freezer refrigerators. This sensor is mounted on or near the evaporator coil and continuously monitors the internal temperature of the refrigerator compartment, transmitting real-time readings to the electronic control board. Based on the data received from the sensor, the control board regulates the compressor, evaporator fan motor, and defrost system to maintain the set temperature. When this sensor fails or drifts out of calibration, the control board receives inaccurate temperature readings — leading to a refrigerator that runs too cold, too warm, or triggers a 5E/SE error code. Features a 9-inch cord for easy installation and a sensitive thermal element with temperature detection accuracy of ±0.1°C. Quick Answer The XPARTCO DA32-10104N Refrigerator Temperature Sensor fixes refrigerators that are too warm, too cold, display a 5E/SE error code, or have inconsistent temperatures that spoil food. It monitors internal refrigerator temperature and sends data to the control board to regulate cooling. Compatible with select Samsung French door, side-by-side, and bottom freezer refrigerators. Common Problems This Part Fixes Refrigerator running too warm — food spoiling faster than normal Refrigerator running too cold — food or drinks freezing in the fresh food section 5E or SE error code displayed on the control panel Inconsistent or fluctuating temperatures inside the refrigerator Compressor running continuously without reaching set temperature Excessive frost or ice buildup on evaporator coils Replaces Part Numbers This sensor directly replaces the following OEM and cross-reference part numbers: DA32-10104N, DA32-10104V, 2030330, ASM1216617, PD00026468, EAP4138666, AP4979323, PS4138666. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This temperature sensor is compatible with select refrigerators from the following brands: Samsung French door refrigerators Samsung side-by-side refrigerators Samsung bottom freezer refrigerators Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Monitors internal refrigerator temperature and sends real-time data to the electronic control board Fixes 5E/SE error codes caused by a faulty or out-of-calibration temperature sensor Temperature detection accuracy of ±0.1°C for precise cooling control 9-inch cord length for easy installation and connection to the control board Aftermarket replacement built to OEM-equivalent quality standards Direct drop-in replacement — no modification required DIY-friendly repair — installs with basic hand tools in 30–45 minutes Product Specifications Part Number DA32-10104N Part Type Refrigerator Temperature Sensor (Thermistor) Condition Aftermarket Replacement Application Refrigerator Temperature Control System Cord Length 9 inches Detection Accuracy ±0.1°C Resistance at 70°F ~9.3K ohms Resistance at 90°F ~7.7K ohms Resistance at 100°F ~6.2K ohms Resistance at 120°F ~4.3K ohms Compatible Brands Samsung Installation Notes ⚠️ Safety First — Unplug Refrigerator Before Starting Unplug the refrigerator from the power source before beginning any repair. Safely remove and store any food that could deteriorate while the power is off. Wear work gloves to protect your hands. The DA32-10104N sensor is located near the evaporator coil, typically behind the rear panel inside the refrigerator or freezer compartment. Remove the panel, locate the sensor along the yellow wire, disconnect the old sensor from its plug, and connect the new sensor in the same position. Reassemble the panel and restore power. Allow 24 hours for the refrigerator to return to normal operating temperature. Tip: Before replacing, test the old sensor with a multimeter — resistance readings outside the values in the specs table above confirm a faulty sensor. Consult your refrigerator's service manual for model-specific instructions. Frequently Asked Questions Will the DA32-10104N fit my Samsung refrigerator? This sensor is compatible with select Samsung French door, side-by-side, and bottom freezer refrigerators. Use the model search above to verify your model, or contact our support team before ordering. What does the temperature sensor do? The temperature sensor (thermistor) continuously monitors the internal temperature of the refrigerator and sends readings to the electronic control board. The control board uses this data to regulate the compressor, fans, and defrost system to maintain the set temperature. When the sensor fails or drifts out of range, the control board receives inaccurate data and cannot maintain proper cooling. What are signs that my temperature sensor needs replacement? Common signs include: the refrigerator running too warm or too cold, food spoiling faster than normal, a 5E or SE error code on the display, inconsistent temperatures, or the compressor running continuously without reaching the set temperature. How do I test the DA32-10104N sensor before replacing it? Use a multimeter to measure the resistance across the sensor terminals. At 70°F the reading should be approximately 9.3K ohms, at 90°F approximately 7.7K ohms, at 100°F approximately 6.2K ohms, and at 120°F approximately 4.3K ohms. Readings significantly outside these values indicate a faulty sensor that needs replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is designed to deliver reliable, accurate temperature sensing at a more affordable price point. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less