ERP 40111201 Dryer Drum Belt
Replaces Part Numbers: WP40111201, 40111201, 14218936, 40051501, 40051502, 59174, AP6009126, PS11742271, R0606549, WP40111201VP, 661570V, 661570, 3387610, 3389728, 3393999, 339728, 661570VP, AP5983729, PS11722115.
Description: This Belt is a replacement part compatible with specific Whirlpool, Maytag, Speed Queen dryer models. The belt attaches to the motor pulley and spins the drum as the motor rotates. Over time, the belt can snap. This is due to general wear and tear, overloading, or excessive friction do to a damaged felt seal. Whenever the dryer belt breaks, the drum will not rotate and would need to be replaced.
This is an aftermarket part that can be used as a replacement for the OEM part.
XPARTCO 6602-001717 Dryer Drum Belt
The XPARTCO 6602-001717 is an aftermarket replacement drum belt for Samsung 24-inch compact dryers. The belt wraps all the way around the outside of the drum, passes under the idler pulley, and loops around the motor pulley — as the motor turns, the belt drags the drum around with it. There is no other mechanical connection between the motor and the drum, which is why a broken belt produces the classic symptom set: the dryer powers on, the console lights up, the motor hums and the blower runs, but the drum sits completely still. Reach in and spin the drum by hand and it will turn freely with no resistance at all.
Samsung specifies this belt as "BELT-TIMING GEAR; 5PH2010, RUBBER, T2.7" — a 5-rib PH-profile belt, 2010 mm long (approximately 79-1/8 inches), 2.7 mm thick, in reinforced rubber. This is a compact-platform belt used on 24" Samsung dryers, and it is physically shorter than the 6602-001655 (5PH2337) belt used on Samsung's full-size 27" dryers. Belts fail from age and heat: the rubber hardens, the ribs glaze over and start slipping, and eventually the belt cracks through or snaps outright. Frayed edges, a squealing or thumping noise that tracks drum rotation, or black rubber dust in the cabinet are all signs the belt is on its way out. Installs in 45–90 minutes with basic hand tools.
Quick Answer
The XPARTCO 6602-001717 Dryer Drum Belt fixes Samsung 24" compact dryers where the motor runs but the drum won't turn, the drum spins freely by hand, or the dryer squeals, thumps, or rumbles during operation. 5 ribs, PH profile, 2010 mm (~79-1/8") long, 2.7 mm thick, reinforced rubber. Also marked 5PH2010. Fits DV22K6800EW and DVE22N6850 compact platforms. Not the same belt as the full-size 6602-001655 / 5PH2337 — that one is over a foot longer.
Common Problems This Part Fixes
Dryer runs and hums but the drum does not turn — the classic broken belt symptom
Drum spins freely by hand with no resistance when the door is open
Loud squealing or screeching that starts as soon as the cycle begins
Rhythmic thumping or slapping noise timed to drum rotation — cracked or split belt
Grinding or rumbling from inside the cabinet as a frayed belt drags
Drum turns slowly, intermittently, or stalls under a heavy wet load — glazed belt slipping
Clothes not drying because the drum isn't tumbling to expose them to airflow
Black rubber dust or belt fragments found in the bottom of the cabinet
Visible cracking, fraying, glazing, or stretching on the old belt
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer drum belt directly replaces the following OEM and cross-reference part numbers:
6602-001717, 6602001717, 5PH2010, SAM6602-001717, AP5623743, EAP4133826, ASM30222, PD00060820, PS4133826.
Samsung has not superseded this belt with a newer number, so the cross-reference list is intentionally short. 5PH2010 is the belt's size designation rather than a separate part number, and it is often stamped on the belt itself — if your old belt is marked 5PH2010, this is the correct replacement. If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Heads up on bad cross-reference data: A number of online listings for 6602-001717 have incorrect cross-references copied onto them from a completely unrelated Frigidaire belt — numbers such as 134163400, AP3865318, 148270, PS1148434, and 5303283471, along with a long list of Frigidaire GLER, FDE, FER, and GLGQ model numbers. Those numbers do not apply to this Samsung belt and those Frigidaire dryers do not use it. If you arrived here from a listing showing those numbers, verify against your Samsung model number before ordering.
Compatibility
This drum belt is compatible with select Samsung 24-inch compact dryers, including:
Samsung DV22K6800EW/A1 and DV22K6800EW/AC compact electric dryers
Samsung DV22K6800EW series (all sub-variants)
Samsung DVE22N6850X and DVE22N6850 series compact electric dryers
Samsung DV22N6800 series compact dryers
Select Samsung-built compact dryers sold under other retail labels
These are Samsung's 24" ventless and compact-footprint dryers, commonly installed in apartments, condos, closets, and stacked laundry towers where a full-size 27" dryer will not fit.
Note — compact platform only: The 6602-001717 is a 2010 mm belt for 24" compact Samsung dryers. It is NOT interchangeable with the 6602-001655 (5PH2337) belt used on Samsung's full-size 27" dryers such as the DV42H, DV45H, DV40J, DV48H, DV48J, and DV50K series — that belt is 2337 mm, roughly 13 inches longer. A full-size belt will hang loose on a compact drum and slip immediately; a compact belt will not stretch far enough to reach around a full-size drum. Measure your old belt or check your model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement drum belt for Samsung 24" compact dryers — transfers motor rotation to the drum
5-rib PH-profile design matched to the compact-platform motor pulley and idler
2010 mm circumference (approximately 79-1/8 inches) — the correct compact-dryer length
2.7 mm thickness in reinforced rubber for heat resistance and long service life
Also identified by its size marking 5PH2010, often stamped on the original belt
Resolves "motor runs but drum won't turn," "squealing," "thumping," and "drum spins freely by hand" symptoms
Multi-rib construction grips the motor pulley without slipping under heavy wet loads
Direct drop-in replacement — no cutting, splicing, or modification required
Aftermarket replacement built to OEM-equivalent quality standards
Straightforward DIY repair — installs in 45–90 minutes with basic hand tools
Product Specifications
Part Number
6602-001717
OEM Part Number
6602-001717
Size Designation
5PH2010
Part Type
Dryer Drum Drive Belt
Condition
Aftermarket Replacement
Application
Samsung 24" Compact Dryers
Length
2010 mm (approx. 79-1/8 in.)
Ribs
5
Profile
PH (multi-rib)
Thickness
2.7 mm
Material
Reinforced rubber
Color
Black
Rib Orientation
Ribbed side faces the drum
Quantity
1 belt
Compatible Brand
Samsung
Installation Notes
⚠️ Unplug Dryer Before Starting — Note Belt Orientation And Idler Routing Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves — the sheet metal edges inside the cabinet are sharp. Before you start, take a photograph of how the old belt routes around the drum, under the idler pulley, and around the motor pulley. If the belt is already broken and you cannot see the original routing, note that the ribbed side of the belt faces toward the drum on this platform, with the smooth back side riding against the idler pulley. Access on Samsung compact dryers is typically through the front: remove the top panel, then the control panel and front panel, which lets you lift the drum out or tilt it forward far enough to work. Vacuum out accumulated lint while the cabinet is open — lint buildup around the motor and idler is what cooks belts prematurely. With the drum accessible, slip the new belt around the drum roughly one-third of the way back from the front lip, ribbed side against the drum surface, and seat it in the wear track left by the old belt. Reach underneath, route the belt under the idler pulley, then loop it around the small motor pulley. A useful trick: tape the belt loosely in position on the drum with a strip of masking tape before you reach underneath, so it doesn't slide off while you're working the idler. Once seated, rotate the drum several full turns by hand and confirm the belt tracks straight and stays centered in its groove without walking toward the edge. While you are in there, spin the idler pulley and the drum rollers by hand — if either is noisy, gritty, or wobbly, replace them now, because a seized idler or worn roller will destroy the new belt in short order. Reassemble, restore power, and run a short empty cycle listening for squeal or thump before putting a load in. Tools needed: Phillips screwdriver, nut driver or socket set, putty knife, masking tape, flashlight, work gloves.
Frequently Asked Questions
How do I know for sure the belt is broken and not the motor?
Open the door with the dryer unplugged and try to spin the drum by hand. With an intact belt you will feel firm resistance — you're turning the motor and idler through the belt. If the drum spins freely and easily, coasting like a bicycle wheel, the belt is broken or has come off its pulleys. The other tell is sound: with a broken belt the motor hums and the blower whooshes normally, so you hear a dryer that sounds like it's running perfectly while the drum sits still. A failed motor, by contrast, usually buzzes and does nothing, or trips the breaker.
Which way do the ribs face on this belt?
On this Samsung compact platform the ribbed side faces toward the drum, so the ribs grip the drum surface and the smooth back of the belt rides against the idler pulley. This is worth stating plainly because belt orientation is not universal across brands — some Whirlpool-platform dryers run the grooves against the motor pulley instead. Photograph your old belt before removing it whenever possible; the wear track polished into the drum will also show you exactly where the belt is meant to sit.
Will the full-size Samsung belt work if I can't find this one?
No. The full-size Samsung belt is 6602-001655, marked 5PH2337 — it is 2337 mm long against this belt's 2010 mm, a difference of about 13 inches. On a compact drum that extra length leaves the belt slack, so the idler cannot take up the tension and the belt slips or walks straight off the pulley. Going the other direction, a compact belt simply will not reach around a 27" drum. The rib count and profile are the same, which is exactly why these two get mixed up — always confirm the length.
My dryer squeals but the drum still turns. Is it the belt or something else?
It could be either, and it's worth diagnosing before you order. A glazed or hardening belt squeals as it slips on the motor pulley, usually loudest at startup and under a heavy wet load. But a dry or failing idler pulley bearing produces a very similar squeal, and worn drum rollers add a low rumble. With the dryer open, spin the idler and each roller by hand: they should turn smoothly and silently. If they're gritty, noisy, or have side-to-side play, replace them along with the belt — the parts share the same teardown, so doing them together saves you from opening the cabinet twice.
Why did my belt break in the first place?
Most often heat and age — rubber hardens over years of thermal cycling until it cracks. But two things dramatically accelerate it. Restricted airflow from a lint-clogged vent makes the cabinet run far hotter than designed, cooking the belt. And a seized idler pulley or a flat-spotted drum roller forces the belt to drag against a stationary surface, which shreds it quickly. If your belt failed early, clean the vent ducting end to end and inspect the idler and rollers before assuming the new belt will simply last.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the dimensions (2010 mm length, 2.7 mm thickness), 5-rib PH profile, reinforced rubber construction, and drum-drive function of the original 6602-001717 belt used in compatible Samsung 24" compact dryers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO W10820036 Washer / Dryer Door Switch
The XPARTCO W10820036 is an aftermarket replacement door switch used on select Whirlpool-built combination washer/dryer units. This switch is a safety interlock: it detects whether the door is fully closed and latched, and it signals the control board that it is safe to run the motor, heater, and water valves. On a combo unit, this single interlock typically governs both the wash and dry portions of the cycle, since both functions share the same drum and door. If the switch fails to detect a closed door — or fails electrically even when the door is closed properly — the control will refuse to start the cycle, or will stop mid-cycle if the switch drops out while running.
Typical failure modes for a part like this include a cracked or worn switch lever that no longer depresses fully when the door closes, internal contacts that have pitted or burned out from years of cycling, and a housing that has come loose from its mounting bracket so the plunger no longer lines up with the door strike. A functioning door switch should click firmly when the door closes and should show continuity across its terminals only when the lever is pressed.
Quick Answer
The XPARTCO W10820036 Washer/Dryer Door Switch is a door safety interlock switch for select Whirlpool-built combination washer/dryer units. It fixes units that won't start with the door closed, stop mid-cycle, or fail to register the door as closed even when it's latched properly. Note: this listing was built from general parts knowledge because current supplier and cross-reference data was not available at build time — see the note below before publishing.
Common Problems This Part Fixes
Washer/dryer combo won't start even though the door is fully closed
Cycle stops partway through, as if the door had been opened
Door doesn't feel like it's "clicking" or latching the way it used to
Console shows a door-related error or won't advance past the door-closed step
Intermittent operation — sometimes starts, sometimes doesn't, depending on how the door is closed
Visibly cracked, loose, or broken switch housing or lever
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This door switch directly replaces the following OEM part number:
W10820036, 279347, 2-2770, 2-50062, 2-5415, 2020, 202770, 233480, 235462, 237194, 238775, 238980, 239868, 24198, 247207, 26000279347, 279290, 287219, 287220, 291679, 291697, 292212, 296141, 296144, 3347287, 338883, 3392266, 3397503, 3399991, 347207, 350526, 359230, 359484, 364090, 364091, 367034, 388322, 389105, 4273196, 4319330, 660308, 687429, 75958, 8224, 83333, 84144, 86628, 89556, 99788, 99838, LP210, AP5985146, AWP41434, EAP334185, PD00023982, PS11723153.
No additional cross-reference numbers have been confirmed for this part yet. If you have a superseded or alternate number for your appliance, contact our support team and we will verify compatibility before you order.
Compatibility
This door switch is intended for select Whirlpool-built washer/dryer combination units, where a single door and drum serve both the wash and dry functions.
Model list not yet confirmed: A specific compatible model list for W10820036 was not available at the time this page was built. Please verify your exact model number before ordering. Contact our support team with your model number and we will confirm fitment before you purchase.
Key Features
Aftermarket replacement door safety switch for Whirlpool-built washer/dryer combo units
Detects whether the door is closed and latched before allowing the wash or dry cycle to run
Resolves "won't start with door closed," "stops mid-cycle," and "door not detected" symptoms
Direct drop-in replacement for the original W10820036 switch — no modification required
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
XPW10820036
OEM Part Number
W10820036
Part Type
Washer/Dryer Combo Door Safety Switch
Condition
Aftermarket Replacement
Application
Whirlpool-Built Washer/Dryer Combination Units
Function
Door-closed safety interlock for wash and dry cycles
Quantity
1 switch
Compatible Brand
Whirlpool (combo platform)
Installation Notes
⚠️ Unplug The Unit Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access to the door switch on combo units is typically through the front or top control panel — photograph the wiring harness before disconnecting it so you can match it exactly on reassembly. Confirm the new switch's lever aligns with the door strike before securing the mounting screws, and test for a firm, positive click when the door closes before restoring power and running a cycle. If your unit's service manual is available, follow its specific access and mounting steps rather than relying solely on general guidance.
Frequently Asked Questions
My combo unit won't start. Is this definitely the door switch?
It's one of the most common causes when a unit refuses to start with the door visibly closed. Before replacing the switch, confirm the door is latching fully and that nothing (a stray sock, a bent strike bracket) is preventing it from closing all the way. If the door latches firmly but the unit still won't start, or a multimeter shows no continuity across the switch terminals when the lever is pressed, the switch itself is the likely culprit.
Does this switch control both the washer and dryer functions?
On combination washer/dryer units, yes — a single door and drum typically serve both functions, so one door switch acts as the safety interlock for both the wash and dry portions of the cycle.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the mounting, switching function, and door-interlock behavior of the original W10820036 switch used in compatible combination washer/dryer units.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 511255P Dryer Drum Belt - Compatible with Speed Queen, Amana, Dryers
Product Description
Ensure smooth drum rotation with the Replacement 511255P Dryer Drum Belt. This high-quality replacement belt, designed for select Speed Queen, Amana dryers, connects the motor pulley to the drum and idler pulley, enabling efficient tumbling during drying cycles. Made of durable rubber with a 5-rib, 4-groove design, it fixes issues like the drum not turning, loud banging or squeaking noises, or extended drying times due to a worn or broken belt.
Note: Includes one belt. Inspect drum rollers, idler pulley, and drum for wear during replacement. Clean lint from the drum and cabinet to prevent overheating. Overloading the dryer can cause premature belt failure.
Replaces part numbers: D511255P, 511255P, 435P3, 510178, 511255, 59174, D511255, AP6285392, PS17001086.
Compatibility:
Compatible with models including but not limited to:
Speed Queen: SDE515DAYW, SDE305DAYW, SDE3606AYW, SDG009WF, SDG305DAWW, SDG3606AWW, ADE7005AYW, PDET910AYW
Huebsch: HDE707WF, HDG709WF
Amana: ALE643RBW, ALE443RAW, LEA30AW (PLEA30AW), LEA60AW (PLEA60AW), DLE330RAW (PDLE330RAW), DLG330RAW (PDLG330RAW), MDET236AYW, MDET336AYW
Kleenmaid: KED453, KED497W-4350, KED513, KED597W-4350, KGD459, KGD499W-3058, KGD519, KGD599W-3058, LEK33AW-4350, LEK37AW-F4350, LGK33AW-3058, LGK37AW-F3058
Verify your model number or contact support for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Speed Queen, Amana, Whirlpool, Maytag, Admiral, Norge, and Roper dryer models.
🔥 Specifications: 5-rib, 4-groove poly-V belt, black rubber, ~93-3/8"L x 3/8"W x 1/16"H, designed for durability and heat resistance.
💰 Cost-Effective Alternative: Replacement belt offers OEM-equivalent performance at a lower price.
🛠️ Easy Installation: Requires a putty knife, Phillips screwdriver, flat-blade screwdriver, work gloves, optional second person; typically installed in 30–60 minutes.
🛡️ Reliable Fixes: Resolves drum not tumbling, loud noises, or extended drying times.
Safety First: Unplug the dryer from the power source and, for gas dryers, shut off the gas valve before installation.
Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Get your dryer back to peak performance today!
Add to cart now for a budget-friendly fix!
Genuine Whirlpool WPW10131172 Dryer Drive Belt - Compatible with Admiral, Amana, Maytag, Whirlpool
Product Description
Ensure efficient drying with the Genuine Whirlpool WPW10131172 Dryer Drive Belt. This OEM drive belt is designed for select Admiral, Amana, Crosley, Inglis, Maytag, and Whirlpool dryers, driving the drum to ensure proper rotation and consistent performance. Made of durable rubber, it delivers reliable tension and flexibility, addressing issues like the drum not spinning, excessive noise, or failure to start.
Note: Includes one drive belt. Disconnect power and gas (if applicable) before installation. Inspect drum rollers and idler pulley for wear during replacement.
Replaces part numbers: WPW10131172, W10131172, 1449763, PD00003839, EAP11748749, AP6015470, PS11748749.
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Admiral, Amana, Crosley, Inglis, Maytag, and Whirlpool dryers.
🔄 Specifications: OEM rubber drive belt, 4 ribs, 3 grooves.
💪 Reliable Performance: Authentic Whirlpool part ensures long-lasting durability and proper tension.
🛠️ Easy Installation: Requires screwdriver, socket wrench, and work gloves; typically installed in 20–30 minutes.
🛡️ Effective Fixes: Resolves drum not spinning, excessive noise, or failure to start issues.
Product Specification
Part Number: Genuine Whirlpool WPW10131172
Component Type: Dryer drive belt
Material: Rubber
Mounting: Tension-mounted around drum and motor pulley
Operating Conditions: Suitable for household and commercial dryer environments
Compliance: Prop 65 warning for California
Installation Notes:
Safety First: Disconnect the dryer from the power source and gas supply (if applicable) before installation.
Shop for high-quality Genuine appliance parts with a 30-day return policy. Keep your dryer running smoothly today!
Add to cart now for a reliable fix!
WE04X24550 Dryer Genuine OEM Timer
Fits Specific GE Dryer Models
Replaces Part Numbers: WE04X24550, WE04X24549, 4546121, AP6031056, PS11763064.
Description: This Dryer Timer is a Genuine OEM part for select GE dryer models. This timer controls the length of the drying cycle by regulating the electrical components of the dryer, such as the heating element and motor. It ensures that the appliance runs for the set amount of time and shuts off automatically at the end of the cycle.
Key Features:
✅ Genuine OEM Part for GE Dryer
🔁 Also replaces: WE04X24549, 4546121, AP6031056, PS11763064.
🕒 Controls cycle duration and mode selection
🛠️ Compatible with many GE, Hotpoint, and RCA dryers
🧰 Direct-fit, plug-in installation
⚠️ Unplug the dryer before servicing. Contact us to confirm fit for your specific model.
📦 Part Number: WE04X24550
341241 Dryer Genuine OEM Drum Belt
The 341241 is a Genuine OEM dryer drum belt compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, and Ikea. The drum belt wraps around the outside of the dryer drum, loops around the motor pulley and idler pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry.
Made from high-strength rubber with reinforced ribs, this belt measures 92-1/4 inches long x 1/4 inch wide and features 4 ribs and 3 grooves. It is flat on one side and ribbed on the other, and is built to resist cracking, stretching, and wear under the high heat and repeated tension cycles of daily dryer use. It also replaces some 5-rib, 4-groove belts. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The 341241 Dryer Genuine OEM Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is coming from the dryer. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, and more. Measures 92-1/4" L x 1/4" W with 4 ribs and 3 grooves.
Common Problems This Part Fixes
Dryer drum not spinning — motor runs but drum stays still
Clothes not tumbling during the drying cycle
Thumping, squealing, or slapping noise during operation
Dryer runs but produces no heat because drum is stationary
Burning rubber smell coming from the dryer
Visible broken or frayed belt pieces found inside the dryer cabinet
Clothes taking too long to dry due to drum not rotating at correct speed
Replaces Part Numbers
This drum belt directly replaces the following OEM and cross-reference part numbers:
341241, 14210003, 2008, 26000341241, 26000349533, 31001026, 31531589, 3389628, 3392665, 3394651, 3399844, 341241VP, 345473, 349533, 529597, 53-0186, 53-1080, 53-1086, 53-1528, 53-1589, 53-2671, 53-2910, 660996, 660997, 661561, 693306, 694088, 694416, 694868, 695055, 697388, 8066065, 8206, 8210, 920H4, 920H5, 99906951, 99989673, 99989674, FSP341241, LB276, LB279, P46-037, P46-149, W10127457, W10131364, AH346995, AP32, EA346995, ER341241, AWP39161, PD00002263, EAP346995, AP2946843, PS346995, TJ341241.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drum belt is compatible with select dryers from the following brands:
Whirlpool dryers (gas and electric)
Kenmore / Sears dryers (select models)
Maytag dryers
KitchenAid dryers
Amana dryers
Roper dryers
Admiral dryers
Jenn-Air dryers
Estate dryers
Magic Chef dryers
Crosley dryers
Inglis dryers
Norge, Modern Maid, Hardwick, Caloric, and Ikea dryers
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Drives the dryer drum via the motor pulley and idler pulley for smooth, consistent tumbling every cycle
92-1/4" length x 1/4" width — 4-rib, 3-groove design; flat on one side, ribbed on the other
Also replaces some 5-rib, 4-groove belts — wide cross-compatibility across Whirlpool-family models
Made from high-strength rubber with reinforced ribs — resists cracking, stretching, and heat damage
Direct replacement for OEM part numbers 341241 and 8066065 — no modification required
Compatible with over a dozen major appliance brands built on the Whirlpool platform
Genuine OEM part — factory-exact fit, materials, and dimensions
DIY-friendly repair — installs in 30–45 minutes with basic hand tools
Often replaced together with the idler pulley (691366) and drum rollers (349241T) for a complete drum drive repair
Product Specifications
Part Number
341241
Part Type
Dryer Drum Drive Belt
Condition
Genuine OEM
Application
Gas and Electric Dryers
Length
92-1/4 inches
Width
1/4 inch
Ribs
4 ribs, 3 grooves
Profile
Flat on one side, ribbed on the other
Material
High-strength rubber with reinforced ribs
Color
Black
Compatible Brands
Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, Ikea
Often Replaced With
691366 Idler Pulley, 349241T Drum Rollers
Installation Notes
⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen, then unscrew the two Phillips screws inside the lint filter housing. Use a putty knife 2 inches from each front corner to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release belt tension at the idler pulley, lift the drum slightly, and slide the old belt off. Loop the new 341241 belt around the drum with the ribbed side facing down (toward the drum). Route the belt around the idler pulley and motor pulley — consult your model's service manual or a model-specific video for the correct belt path. Reassemble and run a test cycle. Tip: While the drum is out, inspect and replace the idler pulley (691366) and drum rollers (349241T) if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool.
Frequently Asked Questions
How does the 341241 differ from the W10205415 and 6602-001655 belts?
All three are 92-inch dryer drum belts, but they differ in width and rib count. The 341241 is 1/4" wide with 4 ribs and 3 grooves. The W10205415 is 3/8" wide with 5 ribs and 4 grooves. The 6602-001655 is 5/16" wide with 5 ribs and 4 grooves designed for Samsung dryers. Always match the part number to your specific model — do not substitute based on appearance alone.
Will this belt fit my Kenmore dryer?
Many Kenmore dryers — especially the popular 110-series — are manufactured by Whirlpool and use the 341241 belt. Check your model number against the compatibility list and contact our support team if you need help confirming the fit before ordering.
How do I know if my drum belt needs to be replaced?
The most obvious sign is that the dryer motor hums but the drum does not spin. You may also notice a thumping or slapping sound during operation, a burning rubber smell, or clothes that are damp after a full cycle. Open the dryer cabinet to visually confirm if the belt is broken, frayed, or stretched.
Should I also replace the idler pulley and drum rollers?
Yes — since the dryer is already disassembled, it is highly recommended to inspect and replace the idler pulley (691366) and drum support rollers (349241T) at the same time. These parts wear at a similar rate and replacing all three together — often sold as a repair kit — prevents having to disassemble the dryer again in the near future.
Is this an OEM or aftermarket part?
This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same belt that came installed in your dryer from the factory — same materials, dimensions, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
17438000001584 Genuine OEM Midea Dryer Belt Safety Switch
The 17438000001584 is a Genuine OEM Midea replacement belt safety switch compatible with select Midea, Criterion, and Insignia electric and gas dryers. This safety switch is positioned near the drive belt and tensioner pulley assembly, where it monitors belt-related conditions and interrupts electrical flow to the motor or heating circuit if a fault or unsafe condition is detected — such as a broken or severely slipped drive belt. This is a key safety mechanism: if the belt fails and the drum can no longer be safely driven, this switch helps prevent the motor from continuing to run unsafely or the heater from continuing to operate without normal airflow from drum rotation.
When this switch fails, the dryer may not start, may shut off unexpectedly during operation, or may fail to heat even though other components test correctly. As a Genuine OEM part manufactured by Midea to factory specifications, the 17438000001584 measures 2"L x 2"W x 3"H and weighs approximately 1 oz. It is found on the same parts diagram as the drive belt, tensioner pulley assembly, and drum support components on compatible models. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The 17438000001584 Genuine OEM Midea Dryer Belt Safety Switch fixes Midea, Criterion, and Insignia dryers that won't start, shut off unexpectedly during operation, or fail to heat despite other components testing normally. Mounted near the drive belt and tensioner pulley assembly — interrupts power if a fault or unsafe belt condition is detected. Dimensions: 2"L x 2"W x 3"H, approx. 1 oz. Genuine OEM. Compatible with Midea MLG45N3BMG, Criterion CDG41N1AW, CDG45N1AW, and related Midea-platform dryer models.
Common Problems This Part Fixes
Dryer not starting — safety switch not signaling normal belt/drive conditions
Dryer shutting off unexpectedly partway through a cycle
Dryer not heating despite the heating element, thermostat, and other components testing normal
Dryer behaving erratically after a drive belt failure or replacement
Intermittent power interruption during operation traced to this switch area
Switch contacts failing continuity test with a multimeter
Replaces Part Numbers
This belt safety switch directly replaces the following part number:
17438000001584, AP7157511, PS18188483
This is the Midea manufacturer part number used across multiple Midea, Criterion, and Insignia dryer models. Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This belt safety switch is compatible with select Midea, Criterion, and Insignia dryers, including:
Midea MLG45N3BMG gas dryer
Midea MLG45N1BWW, MLG45N3BWW, and related MLG gas dryer series
Midea MLE series electric dryers (select models)
Criterion CDG41N1AW, CDG45N1AW gas dryers (air vent series)
Insignia electric and gas dryers built on the Midea platform (select models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance
Safety switch mounted near the drive belt and tensioner pulley assembly
Interrupts electrical flow to the motor or heating circuit if a fault or unsafe belt-related condition is detected
Compact design: 2"L x 2"W x 3"H, approximately 1 oz
Compatible with Midea MLG/MLE series, Criterion CDG series, and Insignia Midea-built dryers
Installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
17438000001584
Part Type
Dryer Belt Safety Switch
Condition
Genuine OEM
Application
Electric and Gas Dryers (Midea platform)
Dimensions
2"L x 2"W x 3"H
Weight
Approximately 1 oz
Location
Near drive belt and tensioner pulley assembly
Compatible Brands
Midea, Criterion, Insignia
Installation Notes
⚠️ Unplug Dryer Before Starting (Shut Off Gas First on Gas Models) — Wear Work Gloves Disconnect power before beginning (and shut off the gas supply first if you have a gas dryer model). Wear work gloves — there are sharp metal edges inside the dryer cabinet. Remove the lint filter housing screws, release the top panel locking clips with a putty knife, and lift the top panel. Remove the front panel to access the drum, drive belt, and tensioner pulley assembly. Locate the belt safety switch in this area — refer to your model's parts diagram to confirm its exact mounting position, as it is positioned near the belt and tensioner pulley support. Photograph the wire connections before disconnecting. Disconnect the wires from the old switch, remove the mounting screw or clip, and pull the switch free. Install the new 17438000001584 switch in the same position, secure the mounting hardware, and reconnect the wires. While this area is open, it's a good time to inspect the drive belt and tensioner pulley for wear, since this switch is related to belt operation. Reassemble the front panel and top panel in reverse order. Restore gas and power, and run a test cycle to confirm the dryer starts and runs normally. Tools needed: Phillips screwdriver, putty knife, work gloves.
Frequently Asked Questions
What does the belt safety switch do?
The belt safety switch monitors belt-related conditions near the drive belt and tensioner pulley assembly and interrupts electrical flow to the motor or heating circuit if it detects a fault or unsafe condition — such as a broken or badly slipped drive belt. This is a protective measure: if the belt has failed and the drum can no longer be driven normally, the switch helps prevent continued unsafe operation of the motor or heater. It works alongside other safety components in the dryer (like the door/cover switch and thermal limiters) as part of an overall safety system.
My dryer just had a belt replacement and now isn't working right — could this switch be involved?
It's possible. Since this switch is positioned near the belt and tensioner pulley assembly, it can be disturbed, dislodged, or its connector improperly reseated during a belt replacement. If your dryer is behaving erratically after a recent belt repair — failing to start, shutting off, or not heating — check that this switch's connector is fully seated and that the switch itself wasn't damaged during the repair. If the connector is good and the switch tests as an open circuit with a multimeter, it has failed and needs replacement.
How do I test if this safety switch has failed?
Unplug the dryer, disconnect the switch's wire connector, and set your multimeter to continuity mode. With the belt and tensioner mechanism in their normal operating position, the switch should show closed continuity (allowing current to flow). If the switch shows an open circuit when it should be closed, it has failed and needs replacement. Always refer to your specific model's wiring diagram to confirm the expected switch state, since exact behavior can vary by dryer model.
Does this switch fit Insignia and Criterion dryers as well as Midea?
Yes — Insignia (Best Buy) and Criterion (Sears/Kmart) are house brands whose dryers in certain configurations are manufactured by Midea and use the same internal components, including this belt safety switch. Confirmed Criterion models include the CDG41N1AW and CDG45N1AW gas dryers. Always verify your specific model number before ordering to confirm compatibility.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same belt safety switch installed in compatible Midea, Criterion, and Insignia dryers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO WE12X10011 Dryer Drum Belt
Description: This Belt is a replacement part compatible with Specific GE dryer models. The belt attaches to the motor pulley and spins the drum as the motor rotates. Over time, the belt can snap. This is due to general wear and tear, overloading, or excessive friction do to a damaged felt seal. Whenever the dryer belt breaks, the drum will not rotate and would need to be replaced.
Replaces Part Numbers:
WE12X10011, 1057513, AH959966, EA959966, AP3421994, PS959966.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: California’s Proposition 65
XPARTCO WE03X32037 Dryer Drum Belt Replaces WE12M24
The XPARTCO WE03X32037 is an aftermarket replacement drum drive belt for GE, Hotpoint, and RCA portable, compact, and unitized stack dryers. The belt is a long, slender loop that wraps all the way around the outside of the drum, passes around the idler tension pulley, and finishes around the small drive motor pulley. That belt is the only mechanical link between the motor and the drum — there are no gears and no direct coupling — so when it breaks, the dryer behaves in a very specific way: the console lights up, the motor runs, the blower moves air, and the drum simply sits there. Open the door and spin the drum by hand and it coasts freely with no resistance at all.
This belt measures approximately 79 inches long and about 1/4 inch wide, with a 4-rib multi-groove profile molded into the inner face. The 79" length is the defining specification here — GE uses several visually similar 4-rib dryer belts across its lineup, and the difference between them is length. Belts fail from heat and age: the rubber hardens, the ribs glaze and begin slipping under a heavy wet load, and eventually the belt cracks through or snaps. Fraying edges, a squeal at startup, a rhythmic thump timed to drum rotation, or black rubber dust in the bottom of the cabinet all point to a belt nearing the end of its life. It directly replaces WE12M24, WE12M9, WE12X79, WE12X0079, AP3418890, AP7186820, PS755943, and related numbers. Installs in 45–90 minutes with basic hand tools.
Quick Answer
The XPARTCO WE03X32037 Dryer Drum Belt fixes GE, Hotpoint, and RCA portable, compact, and stack dryers where the motor runs but the drum won't turn, the drum spins freely by hand, or the dryer squeals, thumps, or rumbles during a cycle. Approximately 79" long, 1/4" wide, 4 ribs, black rubber. Fits DDP1370/DDP1375/DDP1380 portable and DSKP333/DSKS333/DSKS433 stack models. Replaces WE12M24, WE12M9, WE12X79, WE12X0079, AP3418890, AP7186820, PS755943. Not the same belt as the 89-1/2" full-size GE WE12M29 — length is what separates them.
Common Problems This Part Fixes
Dryer runs and hums but the drum does not turn — the classic broken belt symptom
Drum spins freely by hand with no resistance when the door is open
Loud squealing or screeching that begins as soon as the cycle starts
Rhythmic thumping or slapping noise timed to drum rotation — cracked or split belt
Grinding or rumbling from inside the cabinet as a frayed belt drags
Drum turns slowly, intermittently, or stalls under a heavy wet load — glazed belt slipping
Clothes not drying because the drum isn't tumbling to expose them to airflow
Black rubber dust or belt fragments in the bottom of the cabinet
Visible cracking, fraying, glazing, or stretching on the old belt
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer drum belt directly replaces the following OEM and cross-reference part numbers:
WE03X32037, WE12M24, WE12M9, WE12X79, WE12X0079, AP3418890, AP7186820, PS755943, PS16729246, EAP16729246, AH755943, EA755943, 943874, AGE25647, PD00074729
WE03X32037 is the current GE part number; WE12M24 is the long-running legacy number that most service diagrams and older belts still carry. If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drum belt is compatible with select portable, compact, and unitized stack dryers from the following brands:
GE portable and compact electric dryers — DDP1370, DDP1375, and DDP1380 series
GE unitized stack and Spacemaker laundry centers — DSKP333, DSKS333, and DSKS433 series
Hotpoint compact and stack dryers (select GE-built models)
RCA compact and stack dryers (select GE-built models)
Select Kenmore compact dryers built on the GE platform
Verified model numbers include: DDP1370GAM, DDP1370SAM, DDP1370SBM, DDP1375GAM, DDP1375GBM, DDP1375GCM, DDP1375GDM, DDP1375GEM, DDP1375SAM, DDP1375SBM, DDP1380GAM, DDP1380GBM, DDP1380GCM, DDP1380GDM, DDP1380GFM, DDP1380SAM, DDP1380SBM, DDP1380SCM, DDP1380SDM, DDP1380TAM, DSKP333EC0WH, DSKP333EC0WW, DSKP333EC2WW, DSKP333EC3WW, DSKP333EC4WW, DSKP333EC5WW, DSKP333EC6WW, DSKS333EC0WH, DSKS333EC0WW, DSKS333EC2WW, DSKS333EC3WW, DSKS333EC4WW, DSKS333EC5WW, DSKS333EC6WW, DSKS433EA0AA, DSKS433EB3WW, DSKS433EB5WW, DSKS433EB6WW, and DSKS433EB7WW.
Note — 79" portable/compact belt only: GE uses several visually identical 4-rib dryer belts that differ only in length, and they are NOT interchangeable. This belt is approximately 79 inches, for portable, compact, and stack units. It is NOT the WE12M29 / WE03X29897 belt (89-1/2") used on full-size GE dryers, NOT the WE12X10009 belt (87"), and NOT the WE12X10014 / WE12X42 belt (87-13/16"). Fitting a longer belt leaves slack the idler cannot take up, and the belt will slip or walk off the pulley within minutes. Measure your old belt end to end, or verify your full model number, before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement drum drive belt — transfers motor rotation to the dryer drum
Approximately 79" long, the correct length for GE portable, compact, and unitized stack dryers
4-rib multi-groove profile molded into the inner face for positive grip on the motor pulley
1/4" width matched to the original belt track and idler pulley
Durable black rubber construction that resists heat hardening and cracking
Resolves "motor runs but drum won't turn," "squealing," "thumping," and "drum spins freely by hand" symptoms
Multi-rib design prevents slipping under heavy wet loads where a worn belt would stall
Direct drop-in replacement — no cutting, splicing, or modification required
Replaces WE12M24, WE12M9, WE12X79, WE12X0079, AP3418890, AP7186820, PS755943, AH755943, EA755943, and 943874
Compatible with GE, Hotpoint, RCA, and select Kenmore compact and stack dryers
Aftermarket replacement built to OEM-equivalent quality standards
Straightforward DIY repair — installs in 45–90 minutes with basic hand tools
Product Specifications
Part Number
XPWE03X32037
OEM Part Number
WE03X32037 (formerly WE12M24)
Part Type
Dryer Drum Drive Belt
Condition
Aftermarket Replacement
Application
GE Portable, Compact, and Unitized Stack Dryers
Length
Approx. 79 in.
Width
1/4 in.
Ribs
4 ribs / 3 grooves
Material
Rubber
Color
Black
Rib Orientation
Ribbed side faces the drum
Routing
Around drum → idler tension pulley → drive motor pulley
Fuel Type
Electric and gas dryers
Quantity
1 belt
Compatible Brands
GE, Hotpoint, RCA, select Kenmore
Installation Notes
⚠️ Unplug Dryer Before Starting — Photograph Belt Routing First Disconnect power at the outlet or shut off the circuit breaker before beginning. On a gas model, also close the gas shutoff valve before moving the cabinet. Wear work gloves — the sheet metal edges inside the cabinet are sharp. Before removing anything, photograph how the old belt routes around the drum, around the idler tension pulley, and around the motor pulley. If the belt is already broken and the routing isn't visible, note that the ribbed side of the belt faces toward the drum, with the smooth back riding against the idler pulley. Access on these compact and stack units is generally from the front: remove the top panel, then the control panel and front panel, which frees the drum enough to lift or tilt it forward. Vacuum out accumulated lint while the cabinet is open — restricted airflow and lint packed around the motor are what cook belts prematurely. Slip the new belt around the drum roughly one-third of the way back from the front lip, ribbed side against the drum, and seat it in the polished wear track the old belt left behind. Reach underneath, route the belt around the idler pulley, then loop it around the small motor pulley. Useful trick: tape the belt loosely to the drum with a strip of masking tape before you reach underneath, so it can't slide off while you work the idler into position. Many GE idler arms have a locked or pre-loaded position — if yours does, remember to release it after the belt is seated, or the belt will have no tension and the drum will stall under load. Once routed, rotate the drum several full turns by hand and confirm the belt tracks straight and stays centered without walking toward an edge. While you're in there, spin the idler pulley and each drum roller by hand; if any is noisy, gritty, or has side-to-side play, replace it now, because a seized idler or flat-spotted roller will destroy the new belt quickly. Reassemble, restore power, and run a short empty cycle listening for squeal or thump before loading it. Tools needed: Phillips screwdriver, nut driver or socket set, putty knife, masking tape, flashlight, work gloves.
Frequently Asked Questions
How do I confirm the belt is broken and not the motor?
With the dryer unplugged, open the door and try to spin the drum by hand. An intact belt gives firm resistance, because you're turning the motor and idler through the belt. If the drum coasts freely like a bicycle wheel, the belt is broken or has jumped off its pulleys. Sound is the other tell: with a broken belt the motor hums and the blower whooshes normally, so the dryer sounds like it's running perfectly while the drum sits still. A failed motor usually buzzes and does nothing, or trips the breaker outright.
What's the difference between WE03X32037 and WE12M24?
They are the same belt across production revisions. WE12M24 was the long-running legacy GE number and WE03X32037 is the current number that supersedes it. If your dryer's parts diagram or the old belt itself shows WE12M24, WE12M9, WE12X79, or WE12X0079, this listing is the correct replacement. The remaining cross-references (AP3418890, AP7186820, PS755943, AH755943, EA755943, 943874) are catalog identifiers used by various parts distributors for the same belt.
Can I use a longer GE belt if this one is out of stock?
No. GE's 4-rib dryer belts look nearly identical and differ mainly in length, which is precisely why they get substituted by mistake. This belt is about 79"; the full-size GE belt WE12M29 is 89-1/2", and WE12X10009 and WE12X10014 are around 87". On a compact or portable drum, that extra 8 to 10 inches is far more slack than the idler arm can absorb, so the belt runs loose, slips on the motor pulley, and typically walks off within minutes. If you're unsure, lay your old belt flat in a loop and measure its circumference before ordering.
Which way do the ribs face?
On this GE platform the ribbed side faces toward the drum, so the ribs grip the drum surface while the smooth back of the belt rides against the idler pulley. This is worth stating plainly because rib orientation is not universal across manufacturers — some other platforms run the grooves against the motor pulley instead. Whenever possible, photograph the old belt before removing it. The polished wear track on the drum will also show you exactly where the belt is meant to sit.
The dryer squeals but the drum still turns. Belt or something else?
Could be either, and it's worth diagnosing before you order. A glazed or hardening belt squeals as it slips on the motor pulley, usually loudest at startup and under a heavy wet load. But a dry idler pulley bearing makes a very similar squeal, and worn drum rollers add a low rumble underneath. With the cabinet open, spin the idler and each roller by hand — they should turn smoothly and silently. If they're gritty, noisy, or have play, replace them along with the belt, since they share the same teardown and you'd otherwise be opening the dryer twice.
Why did my belt fail in the first place?
Usually heat and age — rubber hardens over years of thermal cycling until it cracks. Two things accelerate it sharply. Restricted airflow from a lint-clogged vent makes the whole cabinet run far hotter than designed, which cooks the belt. And a seized idler pulley or a flat-spotted drum roller forces the belt to drag against a stationary surface, shredding it in short order. If your belt failed unusually early, clean the vent ducting end to end and inspect the idler and rollers rather than assuming the new belt will simply last longer.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the dimensions (approximately 79" length, 1/4" width), 4-rib profile, rubber construction, and drum-drive function of the original WE03X32037 / WE12M24 belt used in compatible GE, Hotpoint, RCA, and related portable, compact, and unitized stack dryers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
EXP651 Dryer Belt and Idler Pulley Kit Replaces WPW10112954, W10837240
The EXP651 is an aftermarket dryer repair kit containing two essential drum drive components for select Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, and Roper dryers. The kit includes one drum belt (replaces WPW10112954) and one idler pulley assembly with bracket (replaces W10837240) — the two parts most commonly worn together when a dryer drum stops spinning or becomes noisy.
Replacing both the belt and idler pulley at the same time is the smart repair choice. Since the dryer must be disassembled to access either part, doing both in one repair saves you from having to take the machine apart again if the second part fails shortly after. This kit covers the two most common failure points in the Whirlpool-family dryer drum drive system.
Quick Answer
The EXP651 Dryer Belt and Idler Pulley Kit fixes dryers where the drum is not spinning, making loud squeaking or grinding noises, or the belt has broken. Includes one 93-1/4" x 5/16" 5-rib drum belt (WPW10112954) and one idler pulley assembly with bracket (W10837240). Compatible with select Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, and Roper dryers.
What's in the Kit
Part 1 of 2
Dryer Drum Belt — Replaces WPW10112954
93-1/4" L x 5/16" W x 1/8" H · 5-rib Multi-V rubber belt · Wraps around drum and connects to motor and idler pulleys to drive drum rotation
Part 2 of 2
Idler Pulley Assembly with Bracket — Replaces W10837240
2-1/8" pulley diameter · 6-1/4" L x 1-1/4" W x 3-7/16" H overall · Plastic/metal construction · Maintains correct belt tension to spin the drum · Fits Whirlpool dryers with lint screen inside door
Common Problems This Kit Fixes
Dryer drum not spinning — motor runs but drum stays still
Loud squeaking, squealing, or grinding noise during operation
Clothes not tumbling during the drying cycle
Thumping or slapping noise when dryer is running
Belt slipping off or repeatedly breaking
Burning rubber smell coming from the dryer
Dryer drum turning erratically or stopping while motor continues to run
Replaces Part Numbers
Drum Belt (WPW10112954) cross-references:
WPW10112954, W10112954, 1447719, AWP48873, PD00003553, EAP11748388, AP6015116, PS11748388.
Idler Pulley Assembly (W10837240) cross-references:
W10837240, W10547287, W10547290, 3387372, 3388674, W10118754, W10118756, W10837240VP, AWP41730, PD00025564, FIX11726337, AP5988716, PS11726337, 279640, AP3094197, 279640VP, 2958, 3388672, 697692, TJ279640, W10468057, AH334244, EA334244, ER279640, PS334244.
If your part numbers are not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This kit is compatible with select dryers from the following brands:
Whirlpool dryers (gas and electric — fits models with lint screen inside door)
Maytag dryers (gas and electric)
Amana dryers
Kenmore / Sears dryers (select Whirlpool-built models)
KitchenAid dryers
Crosley dryers
Admiral dryers
Inglis dryers
Roper dryers
Note: The W10837240 idler pulley fits Whirlpool-family dryers with the lint screen located inside the door. If your dryer has the lint screen on top of the cabinet, a different idler pulley part number may be required. Contact our support team to confirm before ordering.
Key Features
Two-part kit covers the most common drum drive failures in Whirlpool-family dryers in a single repair
Belt: 93-1/4" L x 5/16" W, 5-rib Multi-V rubber — resists cracking, stretching, and heat damage
Idler pulley: 2-1/8" diameter pulley with arm and bracket — maintains correct belt tension for smooth drum rotation
Replacing both parts together saves a second disassembly if the other part fails soon after
Aftermarket replacement built to OEM-equivalent quality standards
Belt directly replaces WPW10112954 / W10112954 — no modification required
Idler pulley directly replaces W10837240 / W10547287 / W10547290 — no modification required
DIY-friendly repair — installs in 30–60 minutes with basic hand tools
Product Specifications
Kit Part Number
EXP651
Condition
Aftermarket Replacement
Application
Gas and Electric Dryers
Kit Includes
1x Drum Belt (WPW10112954), 1x Idler Pulley Assembly with Bracket (W10837240)
Belt Length
93-1/4 inches
Belt Width
5/16 inch
Belt Height
1/8 inch
Belt Ribs
5 ribs, 4 grooves (Multi-V)
Belt Material
Rubber
Pulley Diameter
2-1/8 inches
Pulley Overall Dimensions
6-1/4" L x 1-1/4" W x 3-7/16" H
Pulley Material
Plastic / Metal
Compatible Brands
Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, Roper
Installation Notes
⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen, then unscrew the Phillips screws inside the lint screen housing. Use a putty knife to release the top panel clips and lift the top panel. Remove the front panel to access the drum and drive components. Release belt tension at the old idler pulley, lift the drum slightly, and slide the old belt off. Remove the old idler arm assembly by unscrewing the mounting screw, then install the new W10837240 idler pulley assembly and secure with the screw. Loop the new WPW10112954 belt around the drum with the ribbed side facing inward, then route it around the new idler pulley and motor pulley. Consult your model's service manual or a model-specific repair video for the correct belt path. Reassemble and run a test cycle. Tools needed: Phillips screwdriver, putty knife or flat pry tool.
Frequently Asked Questions
Why should I replace the belt and idler pulley at the same time?
The belt and idler pulley wear together — when one fails, the other is usually close behind. Since the dryer must be fully disassembled to access either part, replacing both in a single repair saves you from having to take the machine apart again soon after. It also protects the new belt from being damaged by a worn pulley, and vice versa.
How does the W10837240 differ from other Whirlpool idler pulleys?
The W10837240 is the updated idler pulley arm and bracket assembly designed for Whirlpool-family dryers that have the lint screen inside the door. It replaces the older W10547287 and W10547290 assemblies. Some older or different Whirlpool models use a different idler pulley style — if you're unsure which one your dryer needs, contact our support team with your model number before ordering.
What is the difference between WPW10112954 and W10112954?
These are the same belt. WPW10112954 is the updated Whirlpool OEM part number that superseded the original W10112954. Both refer to the identical drum belt included in this kit.
Should I also replace the drum rollers at the same time?
It depends on the condition of your rollers. Since the dryer is already fully disassembled, it is a good opportunity to inspect the drum support rollers for flat spots, cracks, or wobbling. If they show any wear, replacing them at the same time is recommended to avoid a third disassembly. Check your model's roller part number before ordering.
Are these OEM or aftermarket parts?
Both parts in this kit are aftermarket replacements built to OEM-equivalent quality standards. They are not genuine Whirlpool OEM parts, but are manufactured to match the dimensions and performance of the original WPW10112954 belt and W10837240 idler pulley assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
WP3387747 Genuine OEM Whirlpool Dryer Heating Element
The WP3387747 is a Genuine OEM Whirlpool replacement dryer heating element assembly compatible with a wide range of Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, and Magic Chef electric dryers — particularly higher-capacity and newer-generation Duet, Cabrio, HE, and GEW/GEQ series models. The heating element is the primary heat source in an electric dryer — a nickel-chromium resistance coil wound on ceramic insulators inside a steel housing. When the coil burns through, the circuit opens and the dryer produces no heat. When the coil shorts to the housing, the dryer runs too hot or heats continuously after the cycle ends — which is a fire hazard requiring immediate repair.
This Genuine OEM part is manufactured by Whirlpool to factory specifications and is rated at 5200W / 240V with two 5/16" male terminals. Note: Whirlpool updated the wattage of this element from the original 5400W down to 5200W — the WP3387747 at 5200W is the correct current OEM replacement for all compatible models. The thermostat and thermal fuse are not included and should be inspected and replaced separately if needed. It directly replaces 3387747, W11344457, W11045584, 80003, 525502, AP6008281, PS11741416, and additional cross-reference numbers. Installs in 20–45 minutes with basic hand tools.
Quick Answer
The WP3387747 Genuine OEM Whirlpool Dryer Heating Element fixes electric dryers that produce no heat, run too hot, heat continuously, or take too long to dry. 5200W / 240V, nickel-chromium coil, two 5/16" male terminals. Thermostat and thermal fuse not included. Genuine OEM. Replaces 3387747, W11344457, W11045584, 80003, AP6008281, PS11741416. Compatible with Whirlpool Duet/Cabrio/HE/GEW/GEQ, Kenmore, Maytag, Amana, KitchenAid, Roper, Estate, Inglis, and more.
Common Problems This Part Fixes
Dryer produces no heat at all — element coil burned through
Dryer takes much longer than normal to dry clothes
Dryer tumbles normally but generates no heat during the cycle
Dryer overheating or running hotter than normal — coil shorted to housing
Dryer continues to heat after the cycle ends — shorted element (fire hazard)
Visible break, burn spot, or sagging coil inside the housing
Burning smell during operation — arcing at a weak point in the coil
Dryer trips the circuit breaker when the heat cycle is selected
Replaces Part Numbers
This heating element directly replaces the following OEM and cross-reference part numbers:
WP3387747, 3387747, 80003, W11045584, W11344457, PD00002365, EAP11741416, AP6008281, AWP47520, FIX11741416, PS11741416, WP3387747VP.
Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This heating element is compatible with select electric dryers only from the following brands and series:
Whirlpool electric dryers — Duet (WED8xxx, WED9xxx), Cabrio (WED7xxx), HE series, GEW9xxx, GEQ9xxx, WED4xxx, WED5xxx and more
Kenmore / Sears electric dryers — 110 series and Whirlpool-built models (including Kenmore HE2, HE3, Elite HE4, 90 series)
Maytag electric dryers — MEDB, MED series
Amana electric dryers
KitchenAid electric dryers
Roper electric dryers
Estate electric dryers
Crosley electric dryers
Inglis electric dryers
Admiral electric dryers
Jenn-Air electric dryers
Magic Chef electric dryers
Note: This is for electric dryers only. Gas dryers use a gas burner and do not have a heating element. Also: do not touch the new element's coil wire with bare hands — skin oils degrade the nickel-chromium wire and significantly shorten element life. Handle by the frame and terminals only.
Key Features
Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance
Primary heat source for electric dryers — nickel-chromium resistance coil generates heat for every drying cycle
Rated 5200W / 240V — current OEM wattage (updated from original 5400W by Whirlpool)
Two 5/16" male terminals — matches original terminal configuration for direct wire connection
Metal and ceramic construction — high-temp terminals and ceramic insulators resist heat fatigue
Thermostat and thermal fuse are not included — inspect and replace separately if needed
Do not touch the coil wire during installation — skin oils degrade nickel-chromium wire
Replaces 3387747, W11344457, W11045584, 80003, AP6008281, and PS11741416
Compatible with Whirlpool Duet, Cabrio, HE, GEW/GEQ series and 11 additional brand platforms
DIY repair — installs in 20–45 minutes with basic hand tools
Product Specifications
Part Number
WP3387747
Part Type
Dryer Heating Element Assembly (Electric)
Condition
Genuine OEM
Application
Electric Dryers Only
Wattage
5200W (updated from original 5400W — current OEM spec)
Voltage
240V AC
Coil Material
Nickel-chromium resistance wire
Terminals
Two 5/16" male terminals
Material
Metal / Ceramic
Color
Black / Silver
Does Not Include
Thermostat or thermal fuse — inspect and replace separately
Handling Note
Do not touch coil wire — skin oils degrade nickel-chromium wire
Compatible Brands
Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef
Installation Notes
⚠️ Unplug Dryer Before Starting — Do Not Touch the Coil Wire Disconnect power before beginning. The heating element housing is accessible from the lower front panel of the dryer on most Duet/Cabrio HE models — remove the front kick panel to access the heater housing without fully disassembling the dryer. For other models, remove the back panel. Before touching the new element, review the wiring layout of the old element so you can reconnect wires to the correct terminals. Do not touch the nickel-chromium coil wire with bare hands at any point — skin oils on the wire cause hot spots that will prematurely burn the element. Handle only by the frame, terminals, and housing. Photograph the existing wiring before disconnecting. Disconnect the element terminal wires and the thermostat and thermal fuse wires. Unscrew the housing and remove the old element. Install the new WP3387747 element, reconnect all wiring in the same positions, reinstall the housing and panels, restore power, and run a test heat cycle. Tools needed: Phillips screwdriver, 1/4" nut driver.
Frequently Asked Questions
My original element was 5400W but this one is 5200W — is that correct?
Yes — Whirlpool intentionally updated the wattage of this heating element from 5400W to 5200W during a design revision. The WP3387747 at 5200W is the current correct OEM replacement for all compatible models that previously used the higher-wattage element. While the wattage is slightly lower, the element is designed to provide equivalent drying performance within the thermal control system of compatible dryers. The updated wattage is by manufacturer design and does not indicate a defect or an incorrect part.
How do I test if the heating element has failed?
Unplug the dryer and disconnect the element terminals. Set your multimeter to continuity or resistance mode. A working element shows resistance — typically around 9–12 ohms for a 5200W/240V element. An open circuit confirms the coil has burned through. Also test each terminal individually against the metal housing frame — a working element shows no continuity between either terminal and the housing. If continuity exists between a terminal and the housing, the element coil is shorted to ground and must be replaced immediately — do not operate the dryer in this condition.
What is the difference between WP3387747 and 279838?
Both are Genuine OEM Whirlpool dryer heating elements, but they are for different model generations and are not interchangeable. The 279838 (5400W, 240V) is for standard-capacity Whirlpool-family dryers — many WTW/NED series and standard front-load models. The WP3387747 (5200W, 240V) is for higher-capacity and newer-generation models including Whirlpool Duet, Cabrio, HE, and GEW/GEQ series. Always verify your exact model number to confirm which heating element is correct for your dryer before ordering.
Why is it important not to touch the element coil wire?
The heating element coil is made of nickel-chromium wire that reaches very high temperatures during operation. Oils from skin contact leave microscopic residue on the wire that creates hot spots when the element heats up — these hot spots cause premature burnout at the contaminated area, often within a few months of installation. Handle the new element by its steel frame, ceramic insulators, and terminals only. If the coil wire is accidentally touched, wipe the contact area with a dry cloth or isopropyl alcohol before installation.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element assembly installed in compatible Whirlpool, Kenmore, Maytag, and related brand electric dryers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
