Search results for "hvac caacitor"

XPARTCO 8572717 Washer Motor Start Capacitor The XPARTCO 8572717 is an aftermarket replacement motor start capacitor for Whirlpool-built top-load washers and washer/dryer combination units. Unlike a run capacitor that stays in the circuit continuously, this start capacitor's job is brief and intense: at the instant the motor is commanded to start, it delivers a strong momentary boost of voltage to help the motor overcome its own inertia and get up to speed quickly. Once the motor reaches running speed, a relay switches it out of the circuit, handing off to the run capacitor for continuous operation. That short, high-stress duty cycle is exactly why start capacitors are a common failure point — they work hard for a fraction of a second on every single cycle start. Rated 189–227 MFD at 125VAC, 60Hz. The capacitor is a black cylindrical component mounted to the rear panel of the washer, held in place by a small plastic retaining clip and wrapped in a foam shield that protects it from moisture. Common failure modes include the internal dielectric breaking down from repeated startup stress, and in some cases the capacitor overheating badly enough to produce visible smoke if it fails while still energized. A failing start capacitor produces a clear symptom: the washer motor hums but won't start, or the motor fails to spin up while other functions of the washer still respond normally. It directly replaces 357021, 3949169, 661606, W10161696, W10244889, AP6013434, AH11746660, EA11746660, EAP11746660, PS11746660, AWP49120, and PD00003006. Quick Answer The XPARTCO 8572717 Washer Motor Start Capacitor fixes Whirlpool-built top-load washers and washer/dryer combos where the motor hums but won't start, the washer won't agitate or spin, or there's a burning smell from the motor area. Includes foam shield. 189–227 MFD, 125VAC, 60Hz. Replaces 357021, 3949169, 661606, W10161696, W10244889, AP6013434, AH11746660, EA11746660, EAP11746660, PS11746660, AWP49120, PD00003006. Capacitors store a dangerous electrical charge even after power is disconnected — always discharge before handling. Common Problems This Part Fixes Washer motor hums but won't start Washer won't agitate Washer won't spin or drain because the motor never starts Burning smell coming from the motor area Washer that starts a cycle but the drum never begins moving Motor that struggles to start under load but may start when the drum is empty Visible discoloration, bulging, or a burnt smell from the capacitor itself Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer motor start capacitor directly replaces the following OEM and cross-reference part numbers: 8572717, WP8572717, 357021, 3949169, 661606, W10161696, W10244889, AP6013434, AH11746660, EA11746660, EAP11746660, PS11746660, AWP49120, PD00003006 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This motor start capacitor is compatible with select Whirlpool-built top-load washers and washer/dryer combination units across the Whirlpool family of brands, including: Whirlpool top-load washers and washer/dryer combos — WET, WGT series Kenmore top-load washers (select Whirlpool-built 110-series models) Maytag, KitchenAid, Jenn-Air, and Amana washers (select models) Roper, Admiral, Hardwick, and Estate washers (select models) Magic Chef, Crosley, Inglis, Norge, Modern Maid, and Caloric washers (select models) Select Ikea washers built on the Whirlpool platform Verified model numbers include: WET4027EW, WET4024EW, LTE5243DQ, WET3300XQ, WGT3300XQ, MTW5670TQ0, SAWS800JQ1, LSN7233BW1, LSR7233DZ1, LSQ8243HQ0, LSQ8512KQ0, LSQ8543JQ0, LSQ8543JQ1, LSQ8543JT0, LSQ8543JT1, LSQ9244EQ0, LSQ9544KQ0, LSQ9549LG0, LSQ9549LG1, LSQ9549LG2, LSQ9549LG3, LSQ9549PW2, 8LSC6244BQ0, and Kenmore 110.72407600, 110.72408440, 110.74414130, 110.81360430, 110.82074620, 110.82984100, 110.91565810, and 110.98573110. Note: This capacitor fits both standalone washers and Whirlpool washer/dryer combination units. Always verify your full model number before ordering, since specifications and mounting can vary by platform. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement start capacitor — delivers a momentary voltage boost to get the washer motor spinning at startup Resolves "motor hums but won't start," "won't agitate," "won't spin," and "burning smell" symptoms caused by capacitor failure Rated 189–227 MFD, 125VAC, 60Hz Includes foam shield to protect against moisture — transfer or reuse per your model's original configuration Direct drop-in replacement — mounts to the same rear panel retaining clip Replaces 357021, 3949169, 661606, W10161696, W10244889, AP6013434, AH11746660, EA11746660, EAP11746660, PS11746660, AWP49120, and PD00003006 Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Jenn-Air, Amana, Roper, and related top-load washers and washer/dryer combos Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 8572717 OEM Part Number WP8572717 Part Type Washer Motor Start Capacitor Condition Aftermarket Replacement Application Top-Load Washers / Washer-Dryer Combos (Whirlpool-Built) Capacitance 189–227 MFD (µF) Voltage 125VAC Frequency 60 Hz Shape Cylindrical (black) Included Components Foam moisture shield Mounting Rear panel, plastic retaining clip Quantity 1 start capacitor Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, Hardwick, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Caloric, Ikea Installation Notes ⚠️ Danger — Capacitors Store A Dangerous Electrical Charge Unplug the washer or shut off the house circuit breaker before beginning. A capacitor stores an electrical charge even after power has been disconnected, and that charge can deliver a serious or fatal shock. Before touching either terminal, discharge the capacitor by shorting its two terminals together using an insulated-handle screwdriver, or by using a proper capacitor discharge tool with a resistor. Never short the terminals with a bare metal tool held with your bare hand. If you are not fully comfortable performing a capacitor discharge safely, have a qualified appliance technician replace this part instead. ⚠️ Transfer The Foam Shield To The New Capacitor Wear work gloves. Remove the washer's console and then the spring clips that secure the top/body assembly to the washer frame, using a putty knife to gently release them. With the body lifted or set aside, locate the capacitor — a black cylindrical component mounted to the rear panel, held in place by a small plastic retaining clip. Using a flat-blade screwdriver, gently pop the plastic clip away from the capacitor to release it. After confirming the capacitor is fully discharged, unplug it from the appliance wiring. Remove the foam shield from the old capacitor and transfer it onto the new one before installing — this shield protects the capacitor from moisture, and skipping it leaves the new part more exposed to washer humidity. Connect the new 8572717 capacitor to the wiring, snap it back into the plastic retaining clip in the same position, and reassemble the body, spring clips, and console in reverse order. Restore power and run a test cycle to confirm the motor starts promptly on both agitate and spin. Tools needed: putty knife, flat-blade screwdriver, Phillips screwdriver, insulated-handle screwdriver or capacitor discharge tool, work gloves. Frequently Asked Questions My washer motor hums but won't start. Is this the right part? Yes, this is the classic symptom of a failed start capacitor. Since this capacitor's entire job is delivering the momentary voltage boost needed to get the motor spinning from a standstill, a failure here often leaves the motor energized and humming but unable to actually overcome its own inertia and start turning. What's the difference between a start capacitor and a run capacitor? A start capacitor works only for a brief moment — it delivers a strong voltage boost the instant the motor is told to start, then a relay switches it out of the circuit once the motor reaches running speed. A run capacitor, by contrast, stays in the circuit continuously while the motor operates, correcting current phase for efficiency. Because the start capacitor works so hard in such a short burst on every single start, it's a more common failure point than a run capacitor on this type of motor. Do I need to reuse the foam shield from my old capacitor? Yes, it's worth transferring. The foam shield wraps around the capacitor to protect it from moisture inside the washer cabinet, and reusing it on the new capacitor helps the replacement hold up the same way the original was designed to. If the foam has degraded significantly, you can skip it, but it's a simple step that adds meaningful protection. My old capacitor got hot and smoked. Is that dangerous? Yes — a capacitor that overheats to the point of smoking has failed in a way that can pose a fire or electrical hazard, and the washer should not be used again until it's replaced. This kind of failure typically happens when a capacitor stays energized longer than it should, generating heat it isn't designed to dissipate. Replace the capacitor and, if the washer's start relay or timer seems to be holding the capacitor in the circuit too long, have that checked as well. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications (189–227 MFD, 125VAC, 60Hz), cylindrical form factor, and mounting configuration of the original WP8572717 start capacitor used in compatible Whirlpool, Kenmore, Maytag, KitchenAid, and related top-load washers and washer/dryer combos. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 297259515 Refrigerator Start Relay & 297286803 Capacitor The XPARTCO 297259515 kit bundles the compressor start relay and the matching run capacitor for Frigidaire, Kenmore, Crosley, Kelvinator, Gibson, Tappan, and Westinghouse refrigerators and freezers. These two components mount together at the compressor and work as a team every time the compressor cycles on: the start relay delivers the initial electrical boost needed to get the compressor's start winding moving, and the run capacitor helps the compressor motor start and run efficiently once it's going. Because they sit side by side on the same compressor terminals and tend to be diagnosed together, replacing both at once is the standard, most reliable fix rather than gambling on which single component has failed. The classic failure symptom for this pair is unmistakable: a repeated clicking sound from the compressor area as the relay tries and fails to start the compressor, paired with a refrigerator and freezer that are both running too warm because the compressor never actually starts. Real-world repair accounts back this up — technicians troubleshooting a clicking-but-not-starting compressor commonly find both the start relay and run capacitor bad at the same time, which is exactly why they're sold together as a kit. It directly replaces, for the relay: 297259502, 297259510, PS11728176, 4378266, AP5986809, EAP11728176; and for the capacitor: AP5306470, 216985001, 297286804, 1465079, 1940424, 215329902, 218909915, 7216985001, 7218909915, AH3495561, EA3495561, PS3495561, and EAP3495561. Quick Answer The XPARTCO 297259515 Refrigerator Start Relay & Capacitor Kit fixes Frigidaire, Kenmore, Crosley, Kelvinator, Gibson, Tappan, and Westinghouse refrigerators and freezers that won't start cooling, run too warm in both compartments, or make a repeated clicking sound from the compressor area. Includes start relay (297259515) and run capacitor (297286803). Capacitors store a dangerous electrical charge even after power is disconnected — always discharge before handling. What's In The Kit Component Part Number Function Compressor Start Relay 297259515 Delivers the initial electrical boost that kickstarts the compressor's start winding, then switches out once the compressor is running. Compressor Run Capacitor 297286803 15 µF, helps the compressor motor start and run efficiently once the relay has engaged it. Common Problems This Kit Fixes Refrigerator won't start cooling at all Fresh food and freezer compartments both running too warm Repeated clicking sound coming from the compressor area Compressor hums but never actually starts running Refrigerator cycling on and off repeatedly without ever cooling properly Refrigerator that stops suddenly during normal operation No cooling despite the refrigerator otherwise appearing to have power Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This start relay and capacitor kit directly replaces the following OEM and cross-reference part numbers: 297259515, 297259502, 297259510, 4378266, AP5986809, EAP11728176, AFR15446, PD00029384, PS11728176, 297286803, AP5306470, 216985001, 297286804, 1465079, 1940424, 215329902, 218909915, 7216985001, 7218909915, 28PRC250150UFEX, AH3495561, EA3495561, EAP3495561, FIX3495561, AFR15479, PD00027525, PS3495561 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This kit is compatible with select Frigidaire refrigerators and freezers, and also fits select Kenmore, Crosley, Kelvinator, Gibson, Tappan, and Westinghouse refrigerators and freezers built on the same platform, including model numbers such as: CFUFH21TW, CFUMC17QW, CCFU17M1TW FFSS2315T, FFSS2315TS0, FFSS2615T, FFSS2615TD0, FFSS2625T, FGSS2335T LFSS2312T, LFSS2612T FFFC22M6QW, FFFC22M6QWG, FFFH17F2QW, FFFH20F2QW, FFFU17M1QW FFVU17F2SC, FFVU17F4QW, FFVU17F4QWE LFFH17F3QW, LFFH20F3QM, LFFH20F3QW TFFU20F2QW, TFFU21M1QW, WWFC22M1SW Note: Always verify your full model number before ordering, and check the printed rating on your original run capacitor before installing the new one — see the capacitor voltage note in Product Specifications below. Contact our support team with your model number if you're unsure. Key Features Complete 2-piece kit — compressor start relay and matching run capacitor in one purchase Addresses the two components most commonly found bad together on a clicking-but-not-starting compressor Resolves "won't start cooling," "runs too warm," and "clicking sound from the compressor" symptoms Run capacitor rated 15 µF Both components mount directly to the compressor terminals Direct drop-in replacement for both original components Replaces the full cross-reference set for 297259515 and 297286803 listed above Compatible with Frigidaire, Kenmore, Crosley, Kelvinator, Gibson, Tappan, and Westinghouse refrigerators and freezers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Kit Part Number 297259515 Kit Contents 1x Compressor Start Relay (297259515), 1x Run Capacitor (297286803) Condition Aftermarket Replacement Capacitor Rating 15 µF Mounting Both components mount directly to the compressor terminals Repair Skill Level Experienced DIYer Quantity 1 kit (1 relay + 1 capacitor) Compatible Brands Frigidaire, Kenmore, Crosley, Kelvinator, Gibson, Tappan, Westinghouse Note on capacitor voltage: Manufacturer-facing sources disagree on this capacitor's voltage rating — some list it as 15µF/120V, others as 15µF/250V. Before installing, check the voltage printed directly on your original capacitor's body and confirm the new capacitor's printed rating matches or exceeds it. We're not publishing a single voltage figure here rather than risk stating the wrong one — contact our support team if you'd like help confirming the correct rating for your model. Installation Notes ⚠️ Danger — The Run Capacitor Stores A Dangerous Electrical Charge Shut off power to the refrigerator at the outlet before beginning. The run capacitor stores an electrical charge even after power has been disconnected, and that charge can deliver a serious shock. Before touching the capacitor's terminals, discharge it by shorting the two terminals together using an insulated-handle screwdriver, or a proper capacitor discharge tool with a resistor. Never short the terminals with a bare metal tool held with your bare hand. ⚠️ Unplug Refrigerator Before Starting — Both Components Mount To The Compressor Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Shut off the water supply as well if your model has an ice maker or water dispenser. Wear work gloves and safety glasses. Have an assistant help pull the refrigerator away from the wall for access to the rear panel. Locate the compressor in the machine compartment at the back or bottom of the unit, and find the start relay and run capacitor mounted directly to its terminals. Photograph the wiring and orientation of both components before removing anything. After confirming the capacitor is fully discharged, disconnect the old relay and capacitor from the compressor terminals, noting each terminal position. Install the new 297259515 relay and 297286803 capacitor from this kit in the same orientation, seating each firmly onto the correct compressor terminals. Reassemble any panels or retainers you removed, restore the water supply if applicable, and push the refrigerator back into place. Restore power and monitor the refrigerator over the next few hours to confirm the compressor starts reliably and both compartments begin cooling. Tools needed: 1/4" nut driver or socket, 1/2" wrench or adjustable wrench, needle nose pliers, flat-head screwdriver, insulated-handle screwdriver or capacitor discharge tool, work gloves, safety glasses. Frequently Asked Questions Do I really need both the relay and the capacitor, or could just one be bad? Either could technically be the sole cause, but in practice, technicians troubleshooting a compressor that clicks but won't start commonly find both the start relay and run capacitor have failed together — they sit on the same terminals under the same electrical stress every time the compressor cycles. Replacing both at once avoids having to open the compressor compartment a second time if the remaining original part fails shortly after. I hear a repeated clicking sound from the back of my refrigerator, but it's not cooling. Is this the kit I need? Yes, this is a textbook symptom for this exact pair of components. The clicking is the sound of the relay repeatedly attempting to engage the compressor's start winding and failing, often because the run capacitor isn't providing the boost the compressor needs to actually get moving. If both compartments are also warm, that confirms the compressor isn't starting at all. Why doesn't this listing state a single voltage rating for the capacitor? We found genuinely conflicting information across manufacturer-facing sources for this specific capacitor — some list it at 120V, others at 250V — and we'd rather flag that honestly than publish a number we can't fully verify. Before installing, check the rating printed directly on your original capacitor's body, and contact our support team if you'd like help confirming the correct value for your model. My refrigerator stopped suddenly during normal operation. Could this kit be the cause? Yes, a failing run capacitor or start relay can cause a refrigerator to stop suddenly, not just fail to start from cold. If your unit was running fine and then abruptly stopped cooling, checking these two components at the compressor is a reasonable next step alongside checking for tripped breakers or other obvious causes. Is this an OEM or aftermarket kit? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Frigidaire OEM kit, but each component is manufactured to match the electrical specifications and terminal fit of the original 297259515 start relay and 297286803 run capacitor used in compatible Frigidaire, Kenmore, Crosley, Kelvinator, Gibson, Tappan, and Westinghouse refrigerators and freezers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10613606 Refrigerator Compressor Start Relay and Capacitor The XPARTCO W10613606 is an aftermarket replacement compressor start relay and capacitor assembly compatible with a wide range of Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Jenn-Air, Admiral, Crosley, Dacor, Hardwick, Inglis, Litton, and Magic Chef refrigerators. The start relay is a small but critical electrical component that plugs directly onto the compressor terminals and provides the initial power surge needed to start the compressor motor. Once the compressor reaches operating speed, the relay drops out — leaving the compressor to run on its own. The capacitor (rated 15µF ±5%, 250VAC) works alongside the relay to store and release the burst of electrical energy needed on startup. When the start relay fails, the compressor cannot start — causing the refrigerator to stop cooling entirely. A failed relay typically produces a clicking sound every few minutes as the compressor tries and fails to start, followed by a short rest, then another attempt. This kit includes both the start relay and the CBB61 capacitor. It directly replaces W10416065, 8208290, 8208368, C8931605, 67003186, 67005560, 67005561, 67005562, 67003764, 8171210, and several additional cross-reference numbers. Installs in under 15 minutes — no tools required in most cases. Quick Answer The XPARTCO W10613606 Refrigerator Compressor Start Relay and Capacitor fixes refrigerators that are not cooling, are too warm, or are making a repeated clicking sound every few minutes as the compressor tries to start. Plugs directly onto the compressor terminals. Kit includes start relay and 15µF 250VAC CBB61 capacitor. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, and more. Replaces W10416065, 8208290, C8931605, 67005560, and more. No tools required — installs in under 15 minutes. Common Problems This Part Fixes Refrigerator not cooling — compressor not running Freezer section too warm or not freezing Both refrigerator and freezer compartments gradually warming up Repeated clicking sound every 2–5 minutes from behind or underneath the refrigerator Compressor hums briefly then shuts off without reaching operating temperature Refrigerator runs but cannot maintain set temperature Shaking the start relay reveals a rattling sound inside — confirms internal failure Replaces Part Numbers This start relay and capacitor kit directly replaces the following OEM and cross-reference part numbers: W10613606, 67005560, 3023300, 67003186, 67003764, 67005561, 67005562, W10416065, 8171210, 8208290, 8208368, W10244032, 302TFBYY, SSP14R302TFR,  AWP41206, C8931605, PD00004905, EAP8746522, AP5787784, PS8746522. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This start relay and capacitor is compatible with select refrigerators from the following brands: Whirlpool refrigerators (side-by-side, French door, bottom-freezer) Kenmore / Sears refrigerators (select Whirlpool-built models) Maytag refrigerators KitchenAid refrigerators Amana refrigerators Jenn-Air refrigerators Admiral refrigerators Crosley refrigerators Dacor refrigerators Hardwick refrigerators Inglis refrigerators Litton refrigerators Magic Chef refrigerators Important: Always verify your refrigerator's model number and compare the old relay's shape and terminal configuration to the new part before installing. Some models may require trimming the wire connector tabs for a proper fit. Contact our support team with your model number if you need confirmation before ordering. Key Features Provides the initial electrical surge needed to start the compressor motor — without it, the compressor cannot run and the refrigerator cannot cool Kit includes both the start relay and the CBB61 run capacitor (15µF ±5%, 250VAC) — everything needed in one package Plugs directly onto the compressor terminals — no wiring or soldering required in most cases Quick rattle test — shake the old relay; if it rattles, the internal contacts have failed and it needs replacement Replaces W10416065, 8208290, C8931605, and over a dozen additional cross-reference part numbers Compatible with 13 major appliance brands on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards Fast DIY repair — installs in under 15 minutes, no tools required in most cases Product Specifications Part Number W10613606 Part Type Refrigerator Compressor Start Relay and Capacitor Kit Condition Aftermarket Replacement Application Refrigerator Compressor (side-by-side, French door, bottom-freezer) Capacitor Type CBB61 Run Capacitor Capacitor Rating 15µF ±5%, 250VAC Kit Includes 1x Start relay, 1x CBB61 capacitor Installation Plug-in — no tools required in most cases Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Jenn-Air, Admiral, Crosley, Dacor, Hardwick, Inglis, Litton, Magic Chef Installation Notes ⚠️ Unplug Refrigerator Before Starting Unplug the refrigerator from the power outlet before beginning. Move the refrigerator away from the wall to access the rear or lower back panel. Remove the rear access panel by unscrewing the retaining screws to expose the compressor. The compressor is a large black dome-shaped component — the start relay and capacitor assembly plugs onto the side terminals. Grip the old relay firmly and pull it straight off the compressor pins. Shake it — if it rattles, the internal contacts have failed and replacement is confirmed. Compare the old relay to the new W10613606 to confirm the terminal layout matches. Align the new relay with the compressor pins and press it firmly on. Reinstall the access panel, restore power, and listen for the compressor to start and run normally within a few minutes. Note: Some models may require trimming the wire connector tabs or reversing the connector orientation for a proper fit — do not force the connection. Tools needed: Phillips screwdriver (for panel access only). Frequently Asked Questions What does the compressor start relay do? The start relay plugs onto the compressor terminals and provides the brief but powerful surge of electrical current needed to start the compressor motor from a standstill. Once the compressor reaches operating speed — usually within a second or two — the relay drops out and the compressor runs on its own. Without a working start relay, the compressor cannot start at all, and the refrigerator stops cooling. The capacitor works alongside the relay to store and deliver the extra energy needed on startup. How do I know if my start relay has failed? The most reliable quick test is the rattle test: unplug the refrigerator, pull the start relay off the compressor, and shake it near your ear. A working relay is silent. A failed relay will rattle — the internal contacts have broken free and are loose inside the casing. Another sign is a repeated clicking sound every 2–5 minutes from the back of the refrigerator, where the compressor attempts to start, fails, trips the overload protector, rests, and tries again. If the fridge is warm and you hear clicking, check the relay first. What is the difference between the start relay and the capacitor? The start relay is the switching device that connects and disconnects the start winding of the compressor motor during startup. The capacitor stores a charge and releases it during startup to give the motor the additional torque it needs to get moving under load. Together they work as a startup system for the compressor. This kit includes both — replacing both at the same time ensures the complete startup circuit is fresh and reliable. My fridge is still not cooling after replacing the start relay — what else could it be? If replacing the start relay does not restore cooling, other possible causes include a failed compressor (the compressor runs but no longer builds pressure), a refrigerant leak in the sealed system, a failed start capacitor (if not replaced along with the relay), a bad overload protector, or a faulty main control board. Listen carefully after installing the new relay — if the compressor now starts and runs but the fridge still doesn't cool after several hours, a sealed system issue or refrigerant problem is likely and will require a certified technician. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications and terminal configuration of the original W10613606 start relay and capacitor assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DA97-15765C Refrigerator Condenser Fan Motor The XPARTCO DA97-15765C is an aftermarket replacement condenser fan motor assembly for Samsung French door refrigerators. This assembly includes both the motor and the fan blade together, and it lives in the compressor/machine compartment at the back or bottom of the refrigerator, where its job is to pull air across the condenser coils and compressor to carry heat away from the refrigeration system. That's a different job from an evaporator fan — this motor cools the mechanical side of the system rather than circulating cold air to your food, so a failing condenser fan tends to affect the whole refrigerator's cooling capacity rather than just one compartment. Rated 12V DC, 0.14A, 1.7W, running at approximately 1,120 RPM. On many Samsung models, a failed condenser fan motor triggers a 23C or 23E error code on the display, alongside symptoms like noticeable vibration or noise from the condenser area, elevated internal temperatures, or the over-temperature alarm sensor tripping. Common causes include normal wear on the motor bearings after prolonged use, blockages from dust and debris accumulation around the coils, or damage from moisture exposure. A fan blade that tries to spin but can't complete a full revolution, or that needs a manual nudge to keep turning, is a classic sign this assembly has started to fail. It directly replaces DA97-15765A, DA97-12842A, DA97-12842B, DA97-12842D, DA97-15765D, AP6001015, PS11733650, EAP11733650, DA31-00340A, RMF002ASSA, and 4959328. Quick Answer The XPARTCO DA97-15765C Refrigerator Condenser Fan Motor fixes Samsung French door refrigerators where the whole unit runs warm, the compressor area is noisy or vibrating, a 23C or 23E error code appears, or the over-temperature alarm trips. Includes motor and fan blade. 12V DC, 0.14A, 1.7W, ~1,120 RPM. Replaces DA97-15765A, DA97-12842A, DA97-12842B, DA97-12842D, DA97-15765D, AP6001015, PS11733650, EAP11733650, DA31-00340A, RMF002ASSA, 4959328. This cools the compressor and condenser coils — a different part and symptom pattern than an evaporator fan, which only affects internal air circulation to the food compartments. Common Problems This Part Fixes Both the fresh food and freezer compartments running warmer than normal at the same time 23C or 23E error code displayed on the control panel Noticeable vibration or unusual noise from the condenser/compressor area at the back or bottom of the cabinet Over-temperature alarm sensor tripping Fan blade that tries to spin but doesn't complete a full revolution Fan blade that stops spinning if not manually nudged to keep turning Refrigerator running constantly as the compressor struggles to keep up Excessive dust or debris buildup visible around the condenser coils and fan Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator condenser fan motor assembly directly replaces the following OEM and cross-reference part numbers: DA97-15765C, DA97-15765A, DA97-15765D, DA97-12842A, DA97-12842B, DA97-12842D, AP6001015, PS11733650, EAP11733650, DA31-00340A, RMF002ASSA, 4959328, OEM18003054, ASM138992, PD00050574 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This condenser fan motor assembly is compatible with select Samsung French door refrigerators, including model numbers such as: RF220NCTABC, RF220NCTASG, RF220NCTASP, RF220NCTASR, RF220NCTAWW RF221NCTABC, RF221NCTASP, RF221NCTAWW RF22K9381SG F261BEAESR This assembly also fits many additional Samsung French door refrigerator models beyond those listed above. Note — condenser fan, not evaporator fan: This motor cools the compressor and condenser coils in the machine compartment at the back or bottom of the refrigerator. It is a completely different part from an evaporator fan motor (such as our DA31-00334C listing), which sits behind the freezer's rear panel and circulates cold air to the food compartments. It is also a different part family from our DA97-20025A condenser fan listing, which serves a different group of Samsung models. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which fan motor your refrigerator needs. Key Features Complete assembly — includes both the motor and the fan blade Aftermarket replacement condenser fan motor — draws air across the condenser coils and compressor to remove system heat Resolves "whole fridge running warm," "23C or 23E error code," "noise or vibration from the compressor area," and "over-temperature alarm" symptoms caused by fan failure Rated 12V DC, 0.14A, 1.7W, approximately 1,120 RPM Direct drop-in replacement matching the original mounting and back panel cam-bracket attachment Replaces DA97-15765A, DA97-12842A, DA97-12842B, DA97-12842D, DA97-15765D, AP6001015, PS11733650, EAP11733650, DA31-00340A, RMF002ASSA, and 4959328 Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — typically completed in under an hour Product Specifications Part Number DA97-15765C OEM Part Number DA97-15765C Part Type Refrigerator Condenser Fan Motor Assembly (Motor + Blade) Condition Aftermarket Replacement Brand Samsung Location Compressor/machine compartment (back or bottom of cabinet) Function Cools the condenser coils and compressor Voltage 12V DC Amperage 0.14 A Wattage 1.7 W Speed ~1,120 RPM Related Error Codes 23C, 23E Quantity 1 fan motor assembly Compatible Brand Samsung Installation Notes ⚠️ Unplug Refrigerator Before Starting — Store Perishable Food Separately Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. Remove all shelves from the upper refrigerator cabinet to improve access. Using a flat-blade screwdriver, gently ease the back panel away from the cabinet — on many models it's retained by a cam bracket and snaps into place, so it should release without excessive force. This exposes the condenser/circulating fan. Before condemning the motor, clear away any dust, lint, or debris built up around the condenser coils and fan blade — restricted airflow from a dirty coil produces symptoms similar to a failing motor and costs nothing to rule out. Photograph the wiring harness connector and the fan blade's position before disconnecting anything. Remove the two screws holding the fan in place, unplug the fan lead harness connector, and remove the defective fan assembly. Install the new DA97-15765C in the same position, reconnect the harness plug, and reinstall and tighten the two mounting screws securely. Confirm the blade spins freely by hand without contacting the housing or coils before reinstalling the back panel — it should snap back into place via the cam bracket. Reinstall the shelves, restore power, and monitor the refrigerator over the next 24 hours to confirm normal, even cooling has returned and any error code has cleared. Tools needed: flat-blade screwdriver, Phillips screwdriver, work gloves. Frequently Asked Questions My display shows a 23C or 23E error code. Does that mean I need this part? It's a strong indicator on many Samsung models, since these codes are commonly associated with condenser fan motor failure. Before ordering, it's still worth a quick visual check — clear any dust or debris from around the condenser coils and fan blade, since a heavily clogged condenser can sometimes trigger similar temperature-related codes. If the error persists after cleaning, or if the fan blade doesn't spin freely by hand, this assembly is the likely fix. The fan blade tries to spin but won't complete a full turn. Is that normal? No — this is a classic sign the motor bearings are wearing out or that something is obstructing the blade. A healthy condenser fan should spin freely and continuously once started. If you find yourself needing to give the blade a manual nudge to keep it turning, or it stalls partway through a rotation, the motor has failed and needs to be replaced rather than repeatedly restarted by hand. Both my fresh food and freezer sections are warm. Is this the right part? Yes, that pattern points toward the condenser fan rather than an evaporator fan. Because the condenser fan cools the compressor and coils that the entire refrigeration cycle depends on, a failing condenser fan tends to reduce cooling capacity across both compartments together, rather than leaving one side fine while the other struggles. Does this include the fan blade, or just the motor? This is a complete assembly that includes both the motor and the fan blade together, so there's no need to transfer a blade from your old unit or source one separately. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications (12V DC, 0.14A, 1.7W, ~1,120 RPM), fan blade design, and mounting configuration of the original DA97-15765C condenser fan motor assembly used in compatible Samsung French door refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPATC3 HVAC 3 AMP ATC Fuse 3 Amp Fuse Pack of 4 Universal Furnace Air Conditioner Control Circuit Board Fuse 3 Amp,  32V (12/24V) Blade Fuse (3A)  Body Material: Plastic Body Style: Plug-In Type: Plastic Tab-Fast Acting Commonly mounted in a fuse holder, block or panel

Read more less

DA97-15765C Refrigerator Genuine OEM Condenser Fan Motor Replaces Part Numbers: DA97-15765C, DA97-15765A, DA97-12842A, DA97-12842B, DA97-12842D, DA97-15765D, AP6001015, PS11733650. Description: This Refrigerator Condenser Fan Motor Assembly is an essential component designed to maintain optimal cooling performance in select Samsung refrigerator models. This Genuine OEM part ensures reliable operation by efficiently circulating air through the condenser coils, preventing overheating and maintaining consistent temperatures.

Read more less

(4 Pack) XPATC5 Furnace & Air Conditioner Control Circuit Board 5 Amp Fuse – Universal HVAC Replacement Product Description Protect your HVAC system’s control board with the XPATC5 Furnace & Air Conditioner Control Circuit Board 5 Amp Fuse (4 Pack). These high-quality aftermarket blade fuses are designed to safeguard furnace and air conditioner control boards from electrical overloads and short circuits. A blown 5-amp fuse can cause the HVAC system to stop working entirely. Replacing it with reliable XPATC5 fuses helps restore operation while protecting sensitive electronic components. XPATC5 fuses are commonly used in residential HVAC systems and are ideal to keep on hand for quick repairs. Replaces Part Numbers ATC-5, ATO-5, 5 Amp HVAC Control Fuse, Furnace Control Board Fuse, Air Conditioner 5A Fuse Compatibility This 5 amp HVAC control board fuse is compatible with many furnace and air conditioner systems from manufacturers including Carrier, Trane, Lennox, Goodman, Rheem, York, and others that use standard ATC/ATO 5-amp blade fuses. Always verify fuse amperage and type before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Built to OEM-equivalent electrical specifications ⚡ 5 Amp Rating – Protects HVAC control boards from overloads 🧯 Critical Safety Component – Helps prevent damage to circuit boards 📦 Convenient 4-Pack – Keep spares on hand for future service 💰 Cost-Effective Solution – Affordable alternative to OEM HVAC fuses 📐 Product Specification Part Number: XPATC5 Component Type: HVAC Control Board Fuse Amperage Rating: 5 Amp Voltage Rating: 32V Fuse Style: ATC / ATO Blade Fuse Quantity: 4-Pack Application: Furnace & air conditioner control boards Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Needle-nose pliers or fuse puller ⚠️ Safety First: Always turn off power to the HVAC system before replacing fuses to avoid electrical shock or equipment damage. Basic Steps: Shut off power to the furnace or air conditioner. Open the control board access panel. Locate the blown 5-amp fuse. Remove and replace it with a new XPATC5 fuse. Restore power and test system operation. ⏱️ Time Required: 5 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket HVAC Parts 🔄 30-Day Return Policy Protect your HVAC system and keep it running — Add to Cart Now for a reliable, budget-friendly solution!

Read more less

XPARTCO WR55X10942C Refrigerator Control Board The XPARTCO WR55X10942C is an aftermarket replacement main control board for GE, Hotpoint, RCA, and select Kenmore refrigerators. This board is the central processor for the refrigeration system — it regulates temperature, manages the defrost cycle, and controls compressor operation, coordinating everything that keeps both the fresh food and freezer compartments at the correct temperature. Electrical surges and ordinary long-term wear are both common causes of this board failing. Manufacturer part number 200D4850G022. A failing control board produces a wide range of symptoms because so many functions run through it: inconsistent or fluctuating temperatures, a refrigerator that runs too warm or too cold, the refrigerator not starting at all, unusual clicking noises as the board misfires relay signals, or ice that melts and refreezes as the defrost cycle malfunctions. It directly replaces WR55X10942, WR55X10942P, WR55X10942CT, WR49X10060, WR55X10024, WR55X10037, WR55X10045, WR55X10056, WR55X10065, WR55X10079, WR55X10083, WR55X10086, WR55X10090, WR55X10097, WR55X10109, WR55X10110, WR55X10151, WR55X10160, WR55X10171, WR55X10174, WR55X10177, WR55X10187, WR55X10188, AP7188100, and PS16729744. Quick Answer The XPARTCO WR55X10942C Refrigerator Control Board fixes GE, Hotpoint, RCA, and select Kenmore refrigerators with inconsistent temperatures, a fridge running too warm or too cold, the unit not starting, clicking noises, or ice that melts and refreezes from a malfunctioning defrost cycle. Manufacturer part number 200D4850G022. Replaces WR55X10942, WR55X10942P, WR55X10942CT, WR49X10060, WR55X10024, WR55X10037, WR55X10045, WR55X10056, WR55X10065, WR55X10079, WR55X10083, WR55X10086, WR55X10090, WR55X10097, WR55X10109, WR55X10110, WR55X10151, WR55X10160, WR55X10171, WR55X10174, WR55X10177, WR55X10187, WR55X10188, AP7188100, PS16729744. GE has released many similar-looking control boards across its refrigerator generations — always confirm your exact model number before ordering, since boards that look alike are not always interchangeable. Common Problems This Part Fixes Refrigerator temperatures fluctuating or running inconsistently Refrigerator running too warm or too cold Refrigerator not starting at all Unusual clicking noises from the refrigerator Ice melting and refreezing due to a malfunctioning defrost cycle Refrigerator or freezer section not cooling properly Symptoms that began suddenly, potentially following an electrical surge Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator control board directly replaces the following OEM and cross-reference part numbers: WR55X10942C, WR55X10942, WR55X10942P, WR49X10060, WR55X10065, WR55X10160, WR55X10187, WR55X10328, WR55X10333, WR55X10335, WR55X10336, WR55X10339, WR55X10358, WR55X10366, WR55X10372, WR55X10379, WR55X10381, WR55X10385, WR55X10396, WR55X10413, WR55X10416, WR55X10426, WR55X10427, WR55X10432, WR55X10436, WR55X10456, WR55X10473, WR55X10474, WR55X10523, WR55X10524, WR55X10526, WR55X10529, WR55X10543, WR55X10552, WR55X10554, WR55X10558, WR55X10589, WR55X10597, WR55X10603, WR55X10606, WR55X10614, WR55X10616, WR55X10626, WR55X10656, WR55X10659, WR55X10699, WR55X10712, WR55X10715, WR55X10722, WR55X10942CT, WR55X11036, AP7188100, AGE29813 PD00074367, 200D2259G017, 200D4850G022, 200D4852G018, 200D4852G024, 200D4854G008, 200D4854G013, 200D6221G013, 200D6221G015, 200D6221G016, WKKT 1304-00-70A. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This control board is compatible with select GE and Hotpoint refrigerators, and also fits select RCA and Kenmore refrigerators built on the GE platform. Note — many similar-looking boards exist: GE has produced numerous refrigerator main control boards across different generations that can look nearly identical to this one, and not all of them are interchangeable despite the resemblance. Always verify your full refrigerator model number before ordering, rather than matching by appearance alone. Contact our support team with your model number and we will confirm fitment before you order. Key Features Aftermarket replacement main control board — regulates temperature, defrost, and compressor operation Resolves "inconsistent temperatures," "won't start," "clicking noises," and "ice melting and refreezing" symptoms caused by control board failure Includes built-in defrost controls Manufacturer part number 200D4850G022 Direct drop-in replacement for the original board mounting and harness connectors Replaces WR55X10942, WR55X10942P, WR55X10942CT, WR49X10060, and a wide range of earlier WR55X-prefix board numbers listed above Compatible with GE, Hotpoint, RCA, and select Kenmore refrigerators Aftermarket replacement built to OEM-equivalent quality standards Moderately difficult repair, typically 15 to 45 minutes Product Specifications Part Number WR55X10942C OEM Part Number WR55X10942C (200D4850G022) Part Type Refrigerator Main Control Board Condition Aftermarket Replacement Brand GE Function Regulates temperature, defrost cycle, and compressor operation Repair Difficulty Moderate — 15 to 45 minutes Quantity 1 control board Compatible Brands GE, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Unplug Refrigerator Before Starting — Handle The Board By Its Edges Unplug the refrigerator or shut off power at the breaker before beginning to avoid electrical hazards. Wear work gloves. Access is typically through a rear cover panel: remove the screws securing the cover to reach the board. Photograph all harness connections before disconnecting anything — this board has multiple connectors, and reconnecting one in the wrong position will cause a malfunction or no-start symptom. Handle the new board by its edges rather than touching the components directly, and avoid working in conditions with static buildup, since these boards can be sensitive to static discharge. Remove the mounting screws, disconnect each harness connector from the old board, and lift it free. Position the replacement WR55X10942C board in the same location, secure it in place, and reconnect all harnesses firmly, matching the original connector locations exactly as photographed. Put the rear cover back on and tighten the screws, then restore power and confirm normal cooling and defrost operation, along with any dispenser or interior lighting behavior your model has. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions My refrigerator temperature keeps fluctuating for no clear reason. Is this the control board? It's a strong possibility, especially if you've already ruled out simpler causes like a door seal that isn't sealing properly or a condenser coil that needs cleaning. Since this board regulates both temperature and the defrost cycle together, a failing board can cause the refrigerator to swing between too warm and too cold as it struggles to manage the system correctly. Could a power surge have caused this failure? Yes, this is a documented and common cause of control board failure. Electrical surges, including those from storms or grid fluctuations, can damage the board's circuitry outright, leading to sudden symptom onset. If your refrigerator's issues started abruptly, especially after a storm or power event, this board is a reasonable first suspect. There are so many similar GE control board part numbers. How do I make sure I'm ordering the right one? This is a real and common point of confusion, since GE has released many visually similar boards across different refrigerator generations that are not all interchangeable. The safest approach is to match your refrigerator's full model number against this listing's compatibility rather than relying on how similar a board looks to your old one. If you're at all unsure, send us your model number and we'll confirm fitment before you order. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the processor, relay switching, defrost control circuitry, and harness connector configuration of the original WR55X10942C control board used in compatible GE, Hotpoint, RCA, and Kenmore refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

DA31-00103A Genuine OEM Refrigerator Condenser Fan Motor - Compatible with Samsung Product Description Ensure efficient cooling with the DA31-00103A Genuine OEM Refrigerator Condenser Fan Motor. This Samsung-manufactured motor is designed as a replacement for select Samsung refrigerators. It powers the fan to circulate air over the condenser coils, dissipating heat to maintain optimal refrigeration performance. This part addresses issues like insufficient cooling, frost buildup, unusual noises (e.g., chirping, buzzing), or the refrigerator running too frequently, often caused by a faulty or worn motor. Note: Includes (1) condenser fan motor (fan blade not included). Disconnect power before installation. Verify compatibility with your refrigerator model. Replaces part numbers: DA31-00103A, IS-27210SCD6A, PD00002207, EAP4138348m AP4140906, 1472692, PS4138348. Compatibility: Compatible with select Samsung refrigerator models, including but not limited to: Samsung: RS2631SL, RS2631SL/XAA, RS2623WW/XAA, RS2624SW, RS2624SW/XAA, RS2624WW, RS2631SW, RS2631SW/XAA, RSC5DBSH, RS2621SW/XAA, RS2623BB, RS2623BB/XAA, RS2623SH, RS2623SL, RS2623VQ, RS2630SH, RS2630WW Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Samsung refrigerators. 🔧 Specifications: Genuine OEM Samsung AC fan motor, 115V, 60Hz, 0.16A, 1300RPM, 1-5/8" shaft. 💪 Reliable Performance: Circulates air to dissipate heat from condenser coils for efficient cooling. 🛠️ Easy Installation: Requires screwdriver and pliers; typically installed in 15–30 minutes. 🛡️ Effective Fixes: Resolves insufficient cooling, frost buildup, noisy operation, or frequent running. Product Specification Part Number: DA31-00103A Component Type: Refrigerator condenser fan motor Material: Metal and plastic Electrical Specs: 115V, 60Hz, 0.16A, 1300RPM, 1-5/8" shaft, quick disconnect Compliance: UL-listed, Prop 65 warning for California. Installation Notes: Safety First: Disconnect the refrigerator from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your refrigerator cooling efficiently today! Add to cart now for a reliable fix!

Read more less

WR84X10055 Genuine OEM Condenser Fan Motor Genuine GE part. GE brands include General Electric, Hotpoint, RCA, and others. Cross Reference Information: WR84X10055, 1093723, AH967775, EA967775, AP3797248, PS967775.     WARNING: California’s Proposition 65 (California Residents Only)

Read more less

WR60X10209 Genuine OEM GE Refrigerator DC Condenser Fan Motor The WR60X10209 is a Genuine OEM GE replacement DC condenser fan motor compatible with a wide range of GE, Hotpoint, RCA, Kenmore, Haier, Monogram, and Café refrigerators in the GSS, GSL, HSS, PSS, PSC, GCE, PCE, and related series. The condenser fan motor is located near the compressor at the rear bottom of the refrigerator. It circulates air across the condenser coils to dissipate heat from the hot refrigerant before it returns to the evaporator — this is an essential step in the refrigeration cycle. Without the condenser fan running, heat builds up around the compressor and condenser coils, causing the refrigerator to run continuously, cool inefficiently, or trip the compressor's thermal overload protection. This Genuine OEM part is manufactured by GE to factory specifications. It is a DC voltage motor rated at 11.3V DC, 2.2W with a 4-pin plastic connector and four color-coded wires (white, blue, red, and yellow). It directly replaces WR60X10042, WR60X10053, WR60X10065, WR60X10080, WR60X10081, WR60X10155, WR60X10216, WR60X24483, WR60X10209-24PK, 1195784, AP4265957, AH1483567, EA1483567, and PS1483567. Installs in 15–30 minutes with basic hand tools. Quick Answer The WR60X10209 Genuine OEM GE Refrigerator DC Condenser Fan Motor fixes GE refrigerators that are not cooling properly, running continuously, making unusual noise from the back, or where the compressor is overheating. 11.3V DC, 2.2W, 4-pin connector (white/blue/red/yellow wires). Genuine OEM. Replaces WR60X10042, WR60X10053, WR60X10065, WR60X10080, WR60X10081, WR60X10155, WR60X10216, WR60X24483, AP4265957, PS1483567. Compatible with GE GSS, GSL, HSS, PSS, PSC, GCE, PCE series and Hotpoint, RCA, Kenmore, Haier, Monogram, Café. Common Problems This Part Fixes Refrigerator not cooling properly — condenser fan not circulating air across coils Refrigerator running continuously without reaching set temperature Compressor overheating — heat not being dissipated from condenser area Unusual noise or grinding from the back or bottom of the refrigerator Condenser fan motor visibly not spinning when compressor is running Refrigerator cycling off frequently on thermal overload protection Food spoilage — refrigerator unable to maintain safe temperatures Replaces Part Numbers This condenser fan motor directly replaces the following OEM and cross-reference part numbers: WR60X10209, 1195784, WR60X10042, WR60X10053, WR60X10065, WR60X10080, WR60X10081, WR60X10155, WR60X10216, 045900390950, 197D2407P013, AGE29194, AH1483567, EA1483567, EAP1483567, AP4265957, PD00001176, PS1483567. Contact our support team with your model number if you need confirmation before ordering. Compatibility This condenser fan motor is compatible with a wide range of refrigerators from the following GE product lines: GE refrigerators — GSS series (GSS22, GSS23, GSS25, GSS26 and related side-by-side models) GE refrigerators — GSL series (GSL22, GSL25 and related models) GE refrigerators — GCE series (GCE21, GCE23 and related models) GE refrigerators — PCE and PSS series (PCE23, PSS25, PSS26 and related Profile models) GE refrigerators — PSC series (PSC23, PSC25 and related Profile models) GE Monogram refrigerators — ZIS, ZISB series (select models) GE Café refrigerators (select models) Hotpoint refrigerators — HSS series (HSS22, HSS25 and related models) RCA refrigerators (select GE-built models) Kenmore / Sears refrigerators (select GE-built models) Haier refrigerators (select GE-platform models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Circulates air across the condenser coils to dissipate heat from the refrigerant and maintain efficient refrigeration cycle operation DC voltage motor rated at 11.3V DC, 2.2W — runs on DC voltage supplied by the refrigerator's control board 4-pin plastic connector with color-coded wires (white, blue, red, yellow) — direct plug-in installation on compatible models Replaces WR60X10042, WR60X10053, WR60X10065, WR60X10080, WR60X10081, WR60X10155, WR60X10216, WR60X24483, and AP4265957 Compatible with GE GSS/GSL/GCE/PCE/PSS/PSC, Hotpoint HSS, Kenmore, Haier, Monogram, Café, and RCA refrigerators DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number WR60X10209 Part Type Refrigerator DC Condenser Fan Motor Condition Genuine OEM Application Refrigerators (side-by-side, French door, bottom-freezer) Voltage 11.3V DC Wattage 2.2W Connector 4-pin plastic plug Wire Colors White, Blue, Red, Yellow Location Near compressor at rear bottom of refrigerator Compatible Brands GE, Hotpoint, RCA, Kenmore, Haier, Monogram, Café Installation Notes ⚠️ Unplug Refrigerator Before Starting Unplug the refrigerator before beginning. Pull the refrigerator away from the wall to access the rear lower back panel. Remove the screws securing the back panel to expose the compressor, condenser coils, and condenser fan assembly. The condenser fan motor is mounted on a bracket near the compressor with the fan blade facing the condenser coil. Take a photo of the wire connector orientation before disconnecting. Disconnect the 4-pin wire connector from the motor. Remove the mounting screws securing the motor to the bracket and slide the old motor out. Note the orientation of the fan blade on the motor shaft — the blade must be reinstalled in the same direction on the new motor (or transferred from the old motor if the new motor does not include a blade). Install the new WR60X10209 motor, reconnect the wire connector, reinstall the back panel, restore power, and confirm the condenser fan spins when the compressor starts. Tools needed: Phillips screwdriver, 1/4" nut driver. Frequently Asked Questions What does the condenser fan motor do in a refrigerator? The condenser fan motor drives a fan blade that circulates ambient air across the condenser coils at the rear of the refrigerator. The condenser coils carry hot high-pressure refrigerant that has just been compressed — the fan removes heat from the refrigerant so it can cool, condense, and return to the evaporator to absorb heat from inside the refrigerator. Without the condenser fan running, heat builds up around the compressor and coils, causing the refrigerator to lose cooling efficiency, run continuously, or — in severe cases — trip the compressor's thermal overload and shut down entirely. Why does this motor use DC voltage instead of AC? Modern GE refrigerators use DC motors for the condenser fan because they are more energy-efficient, quieter, and easier to speed-control by the refrigerator's electronic control board than traditional AC motors. The refrigerator's main control board converts household 120V AC power to 11.3V DC to supply the condenser fan motor. This DC motor runs at a variable speed under board control, which allows GE's refrigerators to optimize fan speed based on cooling demand. How do I confirm the condenser fan motor has failed? Pull the refrigerator away from the wall, unplug it, and remove the rear lower panel. Spin the condenser fan blade by hand — if it is stiff, wobbles, or seizes, the motor bearing has failed. If the blade spins freely but the motor does not run when the refrigerator is plugged in and the compressor starts, check for DC voltage at the motor connector using a multimeter. If the board is supplying approximately 11–12V DC to the motor but the motor is not running, the motor has failed electrically. If no voltage is present, the control board may not be supplying power — a less common but possible failure mode. Does this motor come with the fan blade? The WR60X10209 is the motor only — the fan blade is typically not included and should be transferred from the old motor. When removing the old motor, carefully pull the fan blade off the motor shaft (it presses on — no hardware is typically needed). Press the blade onto the new motor shaft in the same orientation. If the fan blade is cracked or damaged, it should be replaced separately. Installing the blade in the wrong direction will reverse the airflow direction and reduce cooling efficiency. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same DC condenser fan motor installed in compatible GE, Hotpoint, and related brand refrigerators from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

4681JB1029D Refrigerator Genuine OEM Condenser Fan Motor Fits Specific LG, Kenmore Refrigerator Models Replaces Part Numbers: 4681JB1029D, EAU61644104, 1267566, AH3523330, EA3523330, OEM17751134, AP4437783, PS3523330. Description: This Condenser Fan Motor is a Genuine part for specific LG, Kenmore refrigerator models. This motor is responsible for powering the fan that cools the condenser coils, which helps dissipate heat from the refrigerator. Proper functioning of the condenser fan motor is crucial for maintaining the efficiency and cooling performance of the refrigerator. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less