Search results for "oven sensor"

6500JB1008A Refrigerator Genuine OEM Temperature Sensor Replaces Part Numbers: 6500JB1008A, 1395582, AH3529164, EA3529164, AP4440683, PS3529164.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

17438200000404 Genuine OEM Midea Dryer Temperature Sensor (Thermistor) The 17438200000404 is a Genuine OEM Midea replacement dryer temperature sensor (thermistor) compatible with an extensive range of Midea, Criterion, and Insignia electric and gas dryers. This NTC (negative temperature coefficient) thermistor continuously monitors air temperature inside the dryer and sends resistance-based readings to the control board, which uses this data to regulate heating element cycling, prevent overheating, and maintain consistent drying temperatures throughout the cycle. As the thermistor heats up, its electrical resistance decreases in a predictable way, allowing the control board to calculate the exact temperature in real time. When this sensor fails — whether shorted, open, or providing drifted/inaccurate readings — the dryer may overheat, may not heat at all, may dry clothes unevenly, may take much longer than normal to complete a cycle, or may trigger a not-heating fault on models with digital displays. As a Genuine OEM part manufactured by Midea to factory specifications, the 17438200000404 directly replaces WF-123X2060 (an alternate catalog cross-reference used by some suppliers, including for compatible Maytag-branded Midea-built units). Installs in 20–30 minutes with basic hand tools. Quick Answer The 17438200000404 Genuine OEM Midea Dryer Temperature Sensor (Thermistor) fixes Midea, Criterion, and Insignia dryers that are overheating, not heating, drying unevenly, or taking too long to dry. NTC thermistor — resistance drops as temperature rises; ~10,000–12,000 ohms at room temperature (70°F). Genuine OEM. Replaces WF-123X2060. Compatible with Midea MLE41N1AWW, MLE45N1AWW/BWW, MLE45N3BMG/BWW, MLE52N3AWW, MLE52S7AGS/AWW, MLG45N1AWW/BWW, MLG45N3BMG/BWW, MLG52S7AGS/AWW, Criterion CDE41N1AW/CDG41N1AW, and a wide range of Insignia models. Common Problems This Part Fixes Dryer overheating — thermistor not accurately reporting rising temperature to the control board Dryer not heating at all — thermistor circuit open or shorted Dryer drying clothes unevenly — inconsistent temperature regulation during the cycle Dryer taking much longer than normal to complete a cycle Not-heating fault code displayed on models with digital control panels Multimeter test shows 0 ohms (shorted) or infinite resistance (open) instead of the expected NTC reading Dryer cycling heat on and off erratically Replaces Part Numbers This temperature sensor directly replaces the following OEM and cross-reference part numbers: 17438200000404, WF-123X2060,  AP7157538, PS18188581 Contact our support team with your model number if you need confirmation before ordering. Compatibility This temperature sensor is compatible with an extensive range of Midea, Criterion, and Insignia dryers, including: Midea electric dryers — MLE41N1AWW, MLE41N1AWWC, MLE45N1AWW, MLE45N1BWW, MLE45N1BWWC, MLE45N3BMG, MLE45N3BWW, MLE52N3AWW, MLE52S7AGS, MLE52S7AWW Midea gas dryers — MLG45N1AWW, MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AGS, MLG52S7AWW Midea — CLADE67W, MDD160A2301E1305, MDD160VG012F0110EUS13 Criterion — CDE41N1AW (electric), CDG41N1AW (gas) Insignia electric dryers — NSDRE67WH8A, NSDRE67WH8AC, NSFDRE67WH8A, NSFDRE67WH8AC, NSFDRE77WH8B, NSFDRE77WH8BC, NSTDRE67W1, NSTDRE75W1 Insignia gas dryers — NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1 Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance NTC (negative temperature coefficient) thermistor — resistance decreases predictably as temperature rises, allowing precise temperature monitoring Sends real-time temperature data to the control board to regulate heating element cycling and prevent overheating Approximately 10,000–12,000 ohms of resistance at room temperature (around 70°F) when functioning correctly Compatible across both electric and gas Midea-platform dryers, including Criterion and Insignia house-brand models Replaces WF-123X2060 Installs in 20–30 minutes with basic hand tools Product Specifications Part Number 17438200000404 Part Type Dryer Temperature Sensor (NTC Thermistor) Condition Genuine OEM Application Electric and Gas Dryers (Midea platform) Sensor Type NTC (Negative Temperature Coefficient) Resistance at Room Temp Approximately 10,000 – 12,000 ohms (~70°F) Location Blower housing/exhaust duct or drum cavity, depending on model Compatible Brands Midea, Criterion, Insignia Installation Notes ⚠️ Unplug Dryer Before Starting (Shut Off Gas First on Gas Models) Disconnect power before beginning (and shut off the gas supply first if you have a gas dryer model). Midea dryers typically have 2–3 temperature sensors: an exhaust thermistor on the blower housing or exhaust duct, a drum thermistor inside the drum cavity, and on heat pump models, an evaporator thermistor — confirm which sensor location matches your symptom and part diagram before starting. Access the sensors by removing the back panel on vented models, or the side/bottom panels on heat pump models. Photograph the connector position before disconnecting. Unplug the old sensor's connector and inspect it for corrosion or heat discoloration on the wires — discoloration indicates prior overheating in that area. Remove the mounting clip or screw securing the old sensor and pull it free. Install the new 17438200000404 sensor in the same position, reseat the connector firmly, and secure the mounting hardware. Reassemble the panel, restore power, and run a test heat cycle to confirm normal temperature regulation. Tools needed: Phillips screwdriver, multimeter (for testing). Frequently Asked Questions How do I test if the temperature sensor (thermistor) has failed? Unplug the dryer, disconnect the sensor's connector, and set your multimeter to resistance mode. At room temperature (around 70°F), a working NTC thermistor should read approximately 10,000 to 12,000 ohms. If the sensor reads 0 ohms, it has shorted internally. If it reads infinite resistance (open circuit, often shown as "OL" on the multimeter), the sensor has failed open. Either reading confirms the sensor needs replacement. If you have multiple sensors testing bad at the same time, check the shared ground wire — a broken ground connection can cause all sensors on that circuit to read as open even if the individual sensors are fine. My Midea dryer has more than one temperature sensor — how do I know which one to replace? Midea dryers typically use 2–3 temperature sensors depending on the model: an exhaust thermistor mounted on the blower housing or exhaust duct, a drum thermistor inside the drum cavity, and — on heat pump/ventless models — an evaporator thermistor in the refrigerant circuit area. The 17438200000404 is used across this Midea/Criterion/Insignia platform, but confirming the exact mounting location for your specific symptom (e.g., overheating vs. uneven drying) and model number before ordering will help ensure you're replacing the correct sensor. What is the difference between 17438200000404 and WF-123X2060? These are the same temperature sensor. WF-123X2060 is an alternate catalog cross-reference number used by some parts suppliers for the identical Midea-manufactured thermistor — it appears in listings for compatible Maytag-branded Midea-built units as well as the standard Midea, Criterion, and Insignia models. If your dryer's parts diagram shows either number, the 17438200000404 is the correct part. Does this sensor fit my Insignia or Criterion dryer? Yes — Insignia (Best Buy) and Criterion (Sears/Kmart) are house brands whose dryers in this size and configuration are manufactured by Midea and use the same internal components, including this temperature sensor. Confirmed compatible models include Insignia NSDRE67WH8A, NSFDRE67WH8A, NSFDRE77WH8B, NSTDRE67W1, NSTDRE75W1 (electric) and NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1 (gas), as well as Criterion CDE41N1AW (electric) and CDG41N1AW (gas). Always verify your specific model number before ordering. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same NTC thermistor temperature sensor installed in compatible Midea, Criterion, and Insignia dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10316760 Refrigerator Thermistor Sensor – Compatible with Whirlpool, Kenmore, Maytag, and KitchenAid Refrigerators Product Description Maintain accurate refrigerator temperature control with the XPARTCO W10316760 Refrigerator Thermistor Sensor. This Refrigerator Thermistor Sensor is a replacement part for select Kenmore, KitchenAid, Maytag, Whirlpool refrigerator models. It is a crucial component responsible for accurately monitoring and regulating the temperature inside the refrigerator and freezer compartments. Replaces Part Numbers W10316760, WPW10323459, W10323459, 12791417, 12791417SP, 12791419SP, 1876627, W10280385, W10280386, W10308052, W10316760VP, W10438639, W10438761, W10452402, AH2580944, EA2580944, PD00006590, EAP2580944, AP4538142, PS2580944,  Compatibility This replacement thermistor sensor fits select Whirlpool, Kenmore, Maytag, Amana, Jenn-Air, and KitchenAid refrigerators. Example compatible models include (but are not limited to): Whirlpool WRS322FDAW04, Maytag MSS25N4MKZ00, and Kenmore 106.51133213. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature accuracy and response rate ❄️ Precision Cooling Control – Helps maintain stable refrigerator and freezer temperatures 💰 Affordable Alternative – Cost-effective solution versus expensive OEM sensors 🛠️ Simple Installation – Plug-in design for fast, hassle-free replacement 🛡️ Fixes Common Issues – Solves warm fridge, over-cooling, ice buildup, or erratic temperature cycling 📐 Product Specification Part Number: W10316760 Component Type: Refrigerator Thermistor / Temperature Sensor Material: Plastic probe housing with insulated wiring harness Resistance: ~2.7 kΩ at 77°F (varies with temperature) Mounting: Clips or adhesive tape depending on model location Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, needle-nose pliers (optional) ⚠️ Safety First: Always unplug the refrigerator before performing any repairs to prevent electrical shock. Steps: Disconnect power and remove interior shelves for access. Locate the existing thermistor near the evaporator or liner wall. Disconnect the wiring harness and remove any clips or tape. Install the new XPARTCO W10316760 thermistor in the same location. Reconnect the harness, secure wiring, and reassemble interior panels. Restore power and allow several hours for temperatures to stabilize. ⏱️ Time Required: 10–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore accurate refrigerator cooling — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

W11126005CM Dishwasher Wash Vane Sensor Description: This Sensor is a replacement component specifically designed for certain Whirlpool dishwasher models. It plays a crucial role in monitoring cycle conditions like temperature and soil levels to automatically customize wash sequences. Causes of a bad sensor can include leaking or faulty wiring disrupting signals over time, mineral buildup gumming internal mechanisms, or damage from impact. Replaces Part Numbers: W11126005, W11503875, W10380177, W10380483, W10647239, AP6261394, PS12114437. This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: California’s Proposition 65 

Read more less

Choice 240597203 Refrigerator Temperature Sensor Replaces 240597220 The Choice 240597203 is an aftermarket replacement refrigerator temperature sensor compatible with a wide range of Frigidaire, Electrolux, Kenmore (253/106/795 prefix), Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, and Ikea refrigerators and household freezers. This NTC (negative temperature coefficient) thermistor continuously monitors the temperature inside the refrigerator or freezer compartment and sends resistance-based readings to the main control board, which uses this data to cycle the compressor, fans, and defrost heaters to maintain accurate temperatures. As the thermistor heats up or cools down, its electrical resistance changes predictably, allowing the control board to calculate the exact temperature in real time. When this sensor fails or drifts out of range, the refrigerator may run too cold or too warm, cycle excessively, freeze up the evaporator, fail to maintain set temperatures, or display OP error codes. Rated 10K Ohm NTC, with a 5/16" diameter probe, 12" wire, and overall dimensions of 3-5/8"L x 5/8"W x 5/16"H (sensor probe itself measures ~1-3/16"L x 5/16" diameter). Compatible with 20-28 cubic foot North American household refrigerators in French door, side-by-side, top-freezer, and bottom-freezer configurations (post-2005 production). It directly replaces 240597203, 240597220, 240597201, 240597202, 7240597203, AP4032998, AH1765215, EA1765215, EAP1765215, EAP17647917, 1258948, 4985585, OEM21729470, PD00000590, PD00088922, PS1765215, and PS17647917. Not compatible with mini fridges, car refrigerators, commercial units, wine coolers, or ice makers. Installs in 15–20 minutes with basic hand tools. Quick Answer The Choice 240597203 Refrigerator Temperature Sensor fixes Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, and Ikea refrigerators that run too cold or warm, cycle excessively, freeze up the evaporator, or display OP error codes. NTC thermistor — 10K Ohm at room temperature. 5/16" probe diameter, 12" wire. Overall 3-5/8"L x 5/8"W x 5/16"H. Replaces 240597220, 240597201, 240597202, 7240597203, AP4032998, AH1765215, EA1765215, EAP1765215, EAP17647917, 1258948, 4985585, OEM21729470, PD00000590, PD00088922, PS1765215, PS17647917. For 20–28 cu ft household refrigerators built 2005 or later. Common Problems This Part Fixes Refrigerator running too cold or too warm — sensor not accurately reporting temperature Inconsistent temperatures — fluctuating cooling that can't maintain set point OP error code displayed on the control panel (open sensor circuit) Excessive frost or ice buildup on evaporator coils from erratic defrost timing Refrigerator running continuously without cycling off Freezer over-freezing food or fresh food compartment freezing groceries Food spoilage from temperature instability Multimeter test shows 0 ohms (shorted), infinite resistance (open), or drifted resistance instead of the expected ~10K Ohms at room temperature Replaces Part Numbers This temperature sensor directly replaces the following OEM and cross-reference part numbers: 240597220, 240597203, 240597201, 240597202, 7240597203, 4985585, AFR15666, AP7243155, EAP17647917, OEM21729474, PD00088922, PS17647917. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This temperature sensor is compatible with select household refrigerators and freezers from the following brands (20–28 cu ft, built 2005 or later): Frigidaire refrigerators — Gallery and Professional series, plus standard Frigidaire models (BFHS2611LM, BGHS2634KE, BGHS2634KP, BGHS2644KF, CRSH237LB, PRFG2383AF, PRFC2383AF, ERFG2393AS2, FRSS2323AS8, FFHB2740PP5A and many related models) Frigidaire upright freezers — FFFH21F7QW, FGU19F6QWB and related models Electrolux refrigerators — EI24RD65KS0, EI24RD65HS0, EI24RD65HS1, E24RD75KPS0 and related models Kenmore / Sears refrigerators — 253-prefix, 106-prefix, and 795-prefix models (select Frigidaire/Electrolux-built units) Crosley refrigerators (select Frigidaire-built models) White-Westinghouse refrigerators (select models) Kelvinator refrigerators (select models) Gibson refrigerators (select models) Tappan refrigerators (select models) Viking refrigerators (select Frigidaire-platform models) Ikea refrigerators (select Frigidaire-platform models) Not compatible with: mini fridges, car refrigerators, commercial refrigerators/freezers, wine coolers, or dedicated ice makers. Verify your refrigerator was produced after 2005 and check the original part number on the fridge nameplate matches one of the cross-references listed. Contact our support team with your model number if you're unsure. Key Features NTC (negative temperature coefficient) thermistor — resistance changes predictably with temperature, allowing precise temperature monitoring Rated 10K Ohms at room temperature (approximately 25°C / 77°F) Sends real-time temperature data to the main control board to regulate compressor cycling, fan operation, and defrost timing Sensor probe: 5/16" diameter x 1-3/16" length · Overall assembly: 3-5/8"L x 5/8"W x 5/16"H · 12" wire lead White plastic/metal construction with glossy finish Resolves OP error codes when caused by an open sensor circuit Compatible with 20–28 cu ft French door, side-by-side, top-freezer, and bottom-freezer refrigerators built 2005 or later Replaces 18+ OEM and cross-reference part numbers including 240597220, 240597201, 240597202, AP4032998, AH1765215, PS1765215, PS17647917 Compatible with Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, Ikea Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number 240597203CM Part Type Refrigerator Temperature Sensor (NTC Thermistor) Condition Aftermarket Replacement Application Household Refrigerators and Freezers (Frigidaire/Electrolux platform, 20–28 cu ft, 2005+) Sensor Type NTC (Negative Temperature Coefficient) Resistance 10K Ohms at room temperature Probe Dimensions 5/16" Diameter x 1-3/16" Length Overall Dimensions 3-5/8"L x 5/8"W x 5/16"H Wire Length 12" Color White Finish Glossy Material Plastic / Metal Error Codes Resolved OP (open sensor circuit) Compatible Brands Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, Ikea Installation Notes ⚠️ Unplug Refrigerator and Move Perishable Food Before Starting — Wear Work Gloves Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves to protect your hands. Depending on your refrigerator model, the fresh-food temperature sensor is typically located behind the air tower or damper assembly on the rear interior wall of the refrigerator compartment; the freezer temperature sensor is typically located behind the rear freezer access panel near the evaporator coils. Confirm which sensor location matches your symptom and the parts diagram for your specific model before starting. Remove all shelves, drawers, and any items blocking access to the sensor location. Remove the screws holding the air tower/damper cover (fresh food side) or rear freezer access panel to expose the sensor. Photograph the sensor position, wire routing, and connector before removing. Disconnect the wire connector (gently — the connector can be fragile) and release the sensor from its mounting clip. Fully insert the new 240597203 sensor probe into the card slot (no exposure) and secure with the mounting clip. Reconnect the wire connector — plug wiring terminals tightly to avoid poor contact. Use cable ties to secure any loose wire routing as before. Reinstall the cover or panel, replace the shelves and drawers, and plug the refrigerator back in. Allow several hours for the refrigerator to return to its set temperature before reloading with food. Tools needed: Phillips screwdriver, cable ties, multimeter (for testing), work gloves. Frequently Asked Questions What does OP error code mean on my Frigidaire refrigerator? The OP error code (Open) indicates the control board is detecting an open circuit on a temperature sensor input — meaning the sensor is failing to send a resistance signal, either because the sensor itself has failed open internally, the wire has broken, or the connector isn't seated. Replacing the temperature sensor typically resolves the code when the sensor itself is the cause. If the code persists after replacement, check the wire harness between the sensor and the control board for damage, and confirm the connector is fully seated. If the OP code appears alongside other symptoms like frost buildup and cooling issues that persist after sensor replacement, the defrost temperature sensor (on the Harness-Low Side, a different part number) may also need to be replaced, or the main control board may be at fault. How do I test if the temperature sensor has failed? Unplug the refrigerator, disconnect the sensor's wire connector, and set your multimeter to resistance mode. At room temperature (approximately 25°C / 77°F), a working NTC thermistor should read approximately 10K Ohms. If the sensor reads 0 ohms, it has shorted internally. If it reads infinite resistance (open circuit, often shown as "OL" on the multimeter), the sensor has failed open. If it reads significantly off from 10K (for example 8.4K or 5K at room temp), the sensor has drifted and is no longer providing accurate readings — replacement is recommended. Any of these results confirms the sensor needs replacement. My refrigerator has multiple temperature sensors — which one do I replace? Frigidaire refrigerators typically use multiple temperature sensors: one in the fresh food compartment (behind the air tower/damper), one in the freezer compartment (near the evaporator coils), and often a separate defrost temperature sensor on the Harness-Low Side. The 240597203 is used as the fresh food or freezer compartment temperature sensor. If your symptom is "fresh food too warm" or "freezer over-freezing," the fresh food sensor is the likely candidate. If your symptom is "freezer icing up despite defrost heater working," the defrost temperature sensor may be the culprit — a different part number. Check your refrigerator's parts diagram to confirm the correct sensor location for your specific symptom. Does this sensor fit my Kenmore refrigerator? On many Kenmore refrigerators, yes — Sears sells Kenmore-branded refrigerators that are manufactured by Frigidaire/Electrolux, Whirlpool, LG, and Samsung. The 240597203 sensor fits Kenmore refrigerators with model numbers beginning with the 253, 106, or 795 prefixes that are Frigidaire/Electrolux-built. Kenmore refrigerators built by other manufacturers (Whirlpool, LG, Samsung) use different sensors. Check the first three digits of your Kenmore model number — if it's 253, 106, or 795 and falls within the compatible model list, this is the correct part. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured to match the electrical specifications (10K Ohm NTC), probe dimensions (5/16" diameter x 1-3/16" length), wire length (12"), and connector configuration of the original 240597203 temperature sensor used in compatible refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10467289 Washer Genuine OEM Temperature Sensor Replaces Part Numbers: WPW10467289, W10467289, 2629420, 8181705, 8182291, 8540225, 8540226, W10176658, W10176659, OEM18065663, AP6021886,, PS11755214. Description: This Water Temperature Sensor is a Genuine OEM part for specific Kenmore, Whirlpool washing machine models. This sensor ensures the water is reaching the proper temperature at each stage of the wash cycle.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

DA32-00029X Genuine OEM Samsung Refrigerator Temperature Sensor The DA32-00029X is a Genuine OEM Samsung replacement refrigerator temperature sensor compatible with select Samsung side-by-side and French door refrigerators, as well as related Kenmore Samsung-built models. This NTC (negative temperature coefficient) thermistor continuously monitors the temperature inside the refrigerator and sends resistance-based readings to the electronic control board, which uses this data to cycle the compressor, fans, and defrost heaters to maintain accurate, consistent temperatures throughout the appliance. As the thermistor heats up or cools down, its electrical resistance changes predictably, allowing the control board to calculate the exact temperature in real time. When this sensor fails — whether shorted, open, or providing drifted/inaccurate readings — the refrigerator may run too cold or too warm, cycle excessively, fail to maintain set temperatures, run continuously, ice up the evaporator, or display temperature-related fault codes. As a Genuine OEM part manufactured by Samsung to factory specifications, the DA32-00029X is rated approximately 13.2 kΩ at 20°C (68°F) when functioning correctly. It is one of the variants in the DA32-00029 sensor family — Samsung uses different production-run variants (M, N, Q, U, X) across model generations, all functionally similar but with different wire harness connectors. Installs in 20–30 minutes with basic hand tools. Quick Answer The DA32-00029X Genuine OEM Samsung Refrigerator Temperature Sensor fixes Samsung side-by-side and French door refrigerators that run too cold or warm, cycle excessively, freeze up the evaporator, fail to maintain set temperatures, or display temperature-related fault codes. Genuine OEM Samsung NTC thermistor — approximately 13.2 kΩ at 20°C (68°F). One of the DA32-00029 series variants (M, N, Q, U, X) — confirm your specific variant by connector style before ordering. Common Problems This Part Fixes Refrigerator running too cold or too warm — sensor not accurately reporting temperature to the control board Inconsistent temperatures — fluctuating cooling that can't maintain set point Excessive or frequent defrost cycles — control board misreading temperature Refrigerator running continuously without cycling off Heavy frost or ice buildup on the evaporator coils caused by erratic defrost timing Food spoilage from temperature instability Temperature-related error codes displayed on the control panel Multimeter test shows 0 ohms (shorted) or infinite resistance (open) instead of the expected ~13.2 kΩ at room temperature Replaces Part Numbers This temperature sensor directly replaces the following Samsung part number: DA32-00029X, EAP16732853, FIX16732853, ASM30292, AP7188139, OEM21564426, PD00090960, PS16732853. The DA32-00029X is part of the broader DA32-00029 sensor family — variants M, N, Q, U, and X are functionally similar Samsung temperature sensors used across different model generations, but with different wire harness connector configurations. They are not automatically interchangeable — match the variant suffix (or the connector style) to your refrigerator. Contact our support team with your model number if you need confirmation before ordering. Compatibility This temperature sensor is compatible with select Samsung side-by-side and French door refrigerators, including: Samsung side-by-side refrigerators (select models in the RS-series with the matching DA32-00029X connector) Samsung 3-door French door refrigerators in 17.5 cu. ft., 19.5 cu. ft., and related capacities (Black Stainless Steel, Black, White, and Stainless Look finishes) Samsung 4-door French door refrigerators (select RF-series models with the matching DA32-00029X connector) Kenmore / Sears refrigerators (select Samsung-built models) Important — Match the Variant to Your Refrigerator: Samsung uses several variants of the DA32-00029 temperature sensor (M, N, Q, U, X) across different model generations. The sensors are similar in function and resistance value, but the wire harness connectors differ — using the wrong variant means the connector won't fit. Before ordering, verify your refrigerator's parts diagram specifies DA32-00029X (not DA32-00029M, N, Q, or U), or visually confirm the connector on your old sensor matches the new one. Contact our support team with your model number if you're unsure. Key Features Genuine OEM part manufactured by Samsung to factory specifications — guaranteed fit and performance NTC (negative temperature coefficient) thermistor — resistance changes predictably with temperature, allowing precise temperature monitoring Sends real-time temperature data to the control board to regulate compressor cycling, fan operation, and defrost timing Approximately 13.2 kΩ of resistance at 20°C (68°F) when functioning correctly Wire harness with connector attached for direct plug-in installation (variant-specific connector — see compatibility note) One of the DA32-00029 series variants (M, N, Q, U, X) — match to your refrigerator's variant suffix Compatible with select Samsung side-by-side, 3-door French door, and 4-door French door refrigerators, plus Kenmore Samsung-built models Installs in 20–30 minutes with basic hand tools Product Specifications Part Number DA32-00029X Part Type Refrigerator Temperature Sensor (NTC Thermistor) Condition Genuine OEM Application Side-by-Side and French Door Refrigerators (Samsung platform) Sensor Type NTC (Negative Temperature Coefficient) Resistance at 20°C Approximately 13.2 kΩ (68°F) Variant Family DA32-00029 (M, N, Q, U, X variants) Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Refrigerator and Move Perishable Food Before Starting — Wear Work Gloves Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves to protect your hands. Samsung refrigerators typically have multiple temperature sensors — fresh food compartment, freezer compartment, and evaporator/defrost sensors — confirm which sensor location matches your symptom and parts diagram before starting. The fresh food and freezer sensors are typically clipped to a wall or shelf bracket inside each compartment, while evaporator/defrost sensors are mounted near the evaporator coils behind a rear access panel. Take a photo of the sensor mounting and wire routing before removing. Disconnect the sensor's wire connector (gently — the molex connectors can be fragile) and release the sensor from its mounting clip. Inspect the connector for corrosion or heat discoloration on the wires — discoloration indicates prior overheating in that area. Install the new DA32-00029X sensor in the same position, reseat the connector firmly, and secure the mounting clip. Restore power, allow several hours for the refrigerator to return to its set temperature, and confirm stable temperature operation before reloading with food. Tools needed: Phillips screwdriver, multimeter (for testing), work gloves. Frequently Asked Questions How do I know if the temperature sensor has failed? Unplug the refrigerator, disconnect the sensor's connector, and set your multimeter to resistance mode. At room temperature (around 20°C/68°F), a working NTC thermistor should read approximately 13.2 kΩ. If the sensor reads 0 ohms, it has shorted internally. If it reads infinite resistance (open circuit, often shown as "OL" on the multimeter), the sensor has failed open. Either reading confirms the sensor needs replacement. If the sensor reads close to 13.2 kΩ at room temperature but the refrigerator still has temperature problems, the control board or another sensor in the system may be the actual cause. My Samsung refrigerator has multiple temperature sensors — which one do I replace? Samsung refrigerators typically use multiple temperature sensors: one in the fresh food compartment, one in the freezer compartment, and one near the evaporator coils (often called the defrost sensor). The DA32-00029X is used as the fresh food or freezer compartment temperature sensor on select Samsung models. Confirm the exact mounting location for your specific symptom (e.g., fresh food too warm vs. freezer too cold) and your refrigerator's parts diagram before ordering. The evaporator/defrost sensor is typically a different part number, so don't assume the DA32-00029X covers all sensor positions. What is the difference between DA32-00029X and DA32-00029M, N, Q, or U? These are all variants of the same Samsung refrigerator temperature sensor family. They share the same NTC thermistor design and resistance characteristics (approximately 13.2 kΩ at 20°C), but use different wire harness connector configurations to match different refrigerator generations and wiring designs. The X variant is used on select Samsung side-by-side and French door models, while M, N, Q, and U variants appear on other model groups. They are not automatically interchangeable — match the variant to your refrigerator's exact part diagram, or visually compare connector styles before ordering. My Samsung fridge is icing up the back wall — could this be the sensor? Possibly, yes. If the temperature sensor near the evaporator (the defrost sensor) is misreporting temperature, the control board may not trigger the defrost cycle when needed, allowing ice to build up on the evaporator coils. Eventually this ice migrates to the rear interior wall as a frozen sheet. If your symptom is back-wall icing combined with poor cooling, the evaporator sensor is a likely cause — but confirm whether the DA32-00029X is the evaporator sensor on your specific model, or whether your model uses a different part number for that position. Always verify against your model's parts diagram. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Samsung to factory specifications. It is the exact same temperature sensor installed in compatible Samsung side-by-side and French door refrigerators (and Kenmore Samsung-built models) from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DA32-00006S Refrigerator Temperature Sensor – Compatible with Samsung Refrigerators Product Description Restore accurate temperature monitoring and consistent cooling with the XPARTCO DA32-00006S Refrigerator Temperature Sensor. This high-quality aftermarket replacement (also known as a thermistor) measures internal refrigerator or freezer temperatures and sends precise feedback to the control board. A failed or inaccurate sensor can cause temperature fluctuations, over-freezing, warm compartments, or error codes. Replacing it with this reliable XPARTCO sensor helps maintain stable temperatures and proper refrigerator operation. fits select Samsung Refrigerator models XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and performance. Replaces Part Numbers DA32-00006S, PD00002153, EAP4138590, AP4308802, PS4138590. Compatibility This replacement refrigerator temperature sensor fits select Samsung refrigerators. Commonly used in fresh food or freezer compartments depending on model. Always verify your refrigerator’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM resistance and response specifications 🌡️ Accurate Temperature Sensing – Helps maintain consistent cooling ❄️ Fixes Cooling Issues – Resolves temperature swings and sensor-related errors 🧩 Direct-Fit Design – Installs easily without modification 💰 Cost-Effective Repair – Reliable alternative to OEM temperature sensors 📐 Product Specification Part Number: DA32-00006S Component Type: Refrigerator Temperature Sensor (Thermistor) Function: Measures and reports internal temperature Application: Refrigerator or freezer compartment (model dependent) Connector Type: Plug-in wire harness Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver ⚠️ Safety First: Unplug the refrigerator before servicing to avoid electrical shock. Basic Steps: Disconnect refrigerator power. Access the sensor location inside the compartment or behind the panel. Disconnect the old temperature sensor from the wiring harness. Remove the old sensor and install the new XPARTCO DA32-00006S sensor. Reconnect wiring, reassemble panels, and restore power. Allow several hours for temperatures to stabilize. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore accurate temperature control and reliable cooling — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

WB44T10055 Oven Genuine GE OEM Bake Element Oven Bake Element Description: This Oven Bake Element is an OEM part for specific GE oven models, designed to provide the heat necessary for baking. This element is located at the bottom of the oven cavity and turns red hot when electricity flows through it, thereby heating the oven to the desired temperature. It's a crucial component for ensuring your oven can reach and maintain the set baking temperatures, playing a key role in the cooking process by providing consistent, even heat.  The most common cause of bake element failure is normal wear and tear over time. Frequent use can lead to the element burning out, which prevents it from heating. Additionally, physical damage during cleaning or cooking can also cause the element to fail prematurely. Replaces Part Numbers:WB44T10055, 1087447, WB44T10021, AH956152, EA956152, AP3793599, PS956152.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

Choice DA32-10109Y Refrigerator Temperature Sensor – Replacement for Samsung Product Overview The DA32-10109Y Refrigerator Temperature Sensor is an aftermarket replacement part designed to measure and relay internal temperatures to the control board. A faulty sensor can lead to cooling problems, temperature fluctuations, or improper defrost cycles. Replacing a worn sensor with this reliable component helps restore accurate temperature readings and optimal cooling performance in your refrigerator. 8-1/4" overall length with two pin plug for freezer. Fits Samsung SXS refrigerator models. Replaces Part Numbers This sensor replaces part numbers DA32-10109Y, AP4136950, PS4138703. It is engineered to match the fit and functionality of the original Samsung sensor. Compatible Brands Compatible with many Samsung and Kenmore refrigerators manufactured by Samsung. Fits French door, bottom-freezer, and side-by-side models that use this temperature sensor. Fixes the Following Issues Refrigerator not cooling properly Freezer too warm or too cold Temperature reading errors Inconsistent cooling or defrost operation Why Buy from Parts‑O‑Matic Affordable and dependable aftermarket part Fast and free U.S. shipping Easy to install – no special tools required Trusted by appliance techs and DIYers

Read more less

XPARTCO WB13K21 Gas Oven Flat Igniter with Harness The XPARTCO WB13K21 is an aftermarket replacement flat-style gas oven igniter with harness compatible with select GE, Hotpoint, RCA, and Kenmore gas ranges and ovens. The oven igniter is a silicon carbide heating element mounted inside the oven next to the burner. It serves a dual purpose: it draws electrical current through the oven safety valve to hold it open, and it heats to ignition temperature to light the gas burner. The igniter must draw sufficient current — typically 3.2–3.6 amps — to hold the safety valve fully open. A weakened igniter that draws too little current will glow but never fully open the gas valve, preventing the burner from lighting. This flat-style igniter draws 3.4–3.6 amps at 115V. The ceramic block measures 1-1/2" L, with an overall bracket/cage measuring 3-3/4"L x 2-1/8"W x 13/16"H. The harness and plug extend approximately 7-7/8" from the igniter body with female pin connectors and a double wing mounting bracket. It can be used as a bake or broil igniter replacement on compatible models. It directly replaces WB13K21, WB13K12, WB13K13, WB13K14, WB13K0012, WB13K0013, WB13K0014, WB13K0021, WB13K10009, WB13K10026, IG21, 2494, AP2020569, AH231280, EA231280, EAP231280, PS231280, and PD00001023. Note: if the connector does not match your range's harness, cut the connector and splice the wires using porcelain wire nuts — do not use standard plastic wire nuts near the oven burner. Installs in 15–30 minutes with basic hand tools. Quick Answer The XPARTCO WB13K21 Gas Oven Flat Igniter with Harness fixes GE, Hotpoint, RCA, and Kenmore gas ovens that won't heat, where the igniter glows but the burner never lights, or where preheat takes too long. Flat igniter, 3.4–3.6A, 115V. 1-1/2" ceramic block, 3-3/4"L x 2-1/8"W x 13/16"H bracket. 7-7/8" harness with female pins. If connector doesn't match, splice with porcelain wire nuts. Replaces WB13K21, WB13K12, WB13K13, WB13K14, IG21, AP2020569, AH231280, PS231280. Common Problems This Part Fixes Oven not heating — igniter not reaching operating temperature or gas valve not opening Igniter glows orange but the gas burner never lights Oven takes more than 90 seconds to ignite after turning on Oven preheats very slowly — weak igniter no longer drawing enough current to fully open the gas valve Gas smell when oven is turned on but burner does not light Igniter visibly cracked, broken, or burned out Bake or broil function not working on compatible models Replaces Part Numbers This oven igniter directly replaces the following OEM and cross-reference part numbers: WB13K21, WB13K0012, WB13K0013, WB13K0014, WB13K10009, WB13K10026, WB13K12, WB13K13, WB13K14, 2494, AH231280, AP2020569, AGE21391, EA231280, EAP231280, PD00001023, PS231280. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This oven igniter is compatible with select gas ranges and ovens from the following brands: GE gas ranges and ovens (select models) Hotpoint gas ranges and ovens (select models) RCA gas ranges and ovens (select models) Kenmore / Sears gas ranges (select GE-built models) Note: Can be used for both bake and broil igniter replacement on compatible models. If the two-pin connector does not match your range's existing harness connector, cut the connector off the new igniter and splice the wires using porcelain wire nuts — do not use standard plastic wire nuts near the oven burner due to heat. Always verify your model number before ordering. Key Features Flat-style silicon carbide oven igniter — heats to ignition temperature and draws current through the safety valve to open it and allow gas to flow to the burner Draws 3.4–3.6 amps at 115V — correct amperage range to reliably open the GE oven gas safety valve Ceramic block: 1-1/2" L; bracket/cage: 3-3/4"L x 2-1/8"W x 13/16"H Harness and plug extend approximately 7-7/8" from the igniter body Female pin connectors with double wing mounting bracket — quick install on compatible models Can replace bake or broil igniter on compatible models If connector does not match: cut and splice using porcelain wire nuts (included) — never use standard plastic wire nuts near the burner Replaces over 18 older GE oven igniter cross-reference part numbers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number XPWB13K21 Part Type Gas Oven Flat Igniter with Harness (Hot Surface Igniter) Condition Aftermarket Replacement Application Gas Ranges and Ovens (bake and broil) Igniter Style Flat (cageless silicon carbide element) Amperage Draw 3.4 – 3.6 Amps Voltage 115V AC Ceramic Block Length 1-1/2 inches Bracket / Cage Dimensions 3-3/4"L x 2-1/8"W x 13/16"H Harness / Lead Length Approximately 7-7/8 inches from igniter body Connector Type Female pins, two-pin quick-disconnect (splice with porcelain nuts if needed) Mounting Double wing bracket Material Silicon carbide / Ceramic / Metal / Plastic Compatible Brands GE, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Gas Appliance Safety Warning This part is installed in a gas oven. Always unplug the range and shut off the gas supply at the shutoff valve before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. Do not restore power or gas until the repair is fully complete and all connections are secure. If you are not comfortable working on gas appliances, have this part installed by a qualified technician. ⚠️ Handle With Care — Fragile Igniter Element The silicon carbide igniter element is extremely fragile and sensitive to skin oils. Do not touch the igniter element with bare hands — oils from skin will create hot spots that prematurely burn the igniter. Handle only by the bracket, harness, and mounting wings. To install: unplug the range and shut off gas. Remove the oven racks and oven bottom panel. Disconnect the old igniter's wire connector at the connection point inside the oven. Remove the two screws securing the mounting bracket. If the new igniter's connector matches the harness, plug it in directly. If it does not match, cut the connector from the new igniter and use the included porcelain wire nuts to splice the wires to your range's existing harness — do not use plastic wire nuts. Mount the new igniter using the double wing bracket and two screws. Reinstall the oven bottom panel, restore gas and power, and run a bake cycle to confirm the igniter glows and the burner lights within 60–90 seconds. Tools needed: Phillips screwdriver, socket set, work gloves. Frequently Asked Questions My igniter glows but the burner never lights — is it the igniter? Yes, almost certainly. A gas oven igniter that glows orange or red but does not light the burner is a classic sign of a weakened igniter. The igniter must draw enough electrical current — typically 3.2 amps or more — to hold the gas safety valve fully open. As the silicon carbide element ages, its resistance increases and it draws progressively less current. When the current drops below the threshold needed to hold the valve open, the valve never fully opens, even though the igniter appears to glow. If the igniter glows for more than 90 seconds without lighting the burner, it needs to be replaced. Why can't I use plastic wire nuts to splice the igniter wires? The igniter is located inside the oven cavity, directly adjacent to the gas burner, where temperatures during operation can easily exceed what standard plastic wire nuts are rated for. Plastic wire nuts can melt or deform at oven operating temperatures, potentially exposing bare wire connections and creating a short circuit or fire hazard. Porcelain wire nuts are specifically rated for high-temperature applications and are the only safe connector to use when splicing igniter wires near the oven burner. Always use porcelain — never plastic — for any wiring connection inside the oven cavity. Can this igniter be used for both bake and broil? Yes — on compatible GE, Hotpoint, and Kenmore models, the WB13K21 can be used to replace both the bake igniter (lower burner) and the broil igniter (upper burner), as both igniters use the same part number and specifications on these models. Verify your range's parts diagram to confirm that both igniters use the WB13K21 before ordering for the broil position. How do I test if the oven igniter has failed? The most practical test is observation: if the igniter glows for more than 90 seconds without the burner lighting, it has weakened. You can also use a multimeter — disconnect the igniter wires and measure resistance. A working WB13K21-style igniter typically reads between 40 and 90 ohms at room temperature (a lower resistance draws more current; a very high resistance means the element is nearly failed). An open circuit (infinite resistance) means the element has burned through completely. If the igniter does not glow at all when the oven is turned on, it has completely failed electrically. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from silicon carbide, ceramic, metal, and plastic to match the amperage draw, dimensions, and performance of the original WB13K21 oven igniter. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 242278801 Refrigerator Temperature Sensor – Compatible with Frigidaire, Electrolux, and Kenmore Refrigerators Product Description Keep your refrigerator cooling accurately with the XPARTCO 242278801 Refrigerator Temperature Sensor. This high-quality replacement monitors the temperature inside the fresh-food and freezer compartments, sending signals to the control board to regulate cooling. A faulty sensor can cause temperature fluctuations, over-freezing, or warm spots. Replacing it with this reliable XPARTCO part ensures consistent temperature control and energy-efficient performance. Replaces Part Numbers 242278801 PD00029820, EAP8760187, AP5802148, 3016441, PS8760187. Compatibility This replacement temperature sensor fits select Frigidaire, Electrolux, and Kenmore refrigerators. Example compatible models include (but are not limited to): Frigidaire FFHS2611LBNA, Electrolux E23BC78IPS3, and Kenmore 253.7041341C. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature accuracy and response rate ❄️ Accurate Cooling Control – Monitors refrigerator temperature for consistent performance 💰 Cost-Effective Fix – Reliable alternative to expensive OEM parts 🛠️ Simple Installation – Plug-in design for fast, easy replacement 🛡️ Fixes Common Issues – Solves warm refrigerator, freezing, or inconsistent cooling problems 📐 Product Specification Part Number: 242278801 Component Type: Refrigerator Temperature Sensor (Thermistor) Material: Plastic housing with thermistor probe and wiring harness Resistance Range: Approximately 2.7 kΩ at 77°F (varies by temperature) Mounting: Direct-fit installation in refrigerator liner or evaporator area Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, wire clip removal tool ⚠️ Safety First: Always unplug the refrigerator before servicing to prevent electrical shock. Steps: Disconnect power and remove interior shelves for access. Locate the old temperature sensor, usually near the evaporator or rear wall. Disconnect the sensor’s wiring harness and remove clips. Install the new XPARTCO 242278801 sensor in the same position. Reconnect wiring, reassemble interior parts, and restore power. Allow several hours for the refrigerator to stabilize temperature. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Keep your refrigerator cooling efficiently — Add to Cart Now for a reliable, budget-friendly repair!

Read more less