Search results for "refrigerator switch"

WD21X10224 Genuine GE / Hotpoint Dishwasher Interlock Switch Replaces Part Numbers:AP3872949, 1168295, AH1021382, EA1021382, PS1021382   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO W10316760 Refrigerator Thermistor Sensor The XPARTCO W10316760 is an aftermarket replacement temperature thermistor compatible with a wide range of Whirlpool-built refrigerators sold under the Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef brands. The thermistor sits inside the fresh food or freezer compartment and continuously reports internal temperature back to the electronic control board, which uses that reading to cycle the compressor, evaporator fan, and damper to keep the compartment in range. When the thermistor drifts out of calibration or fails outright, the control board loses an accurate temperature signal and the refrigerator commonly responds with erratic cooling, a warmer-than-normal compartment, food freezing when it shouldn't, or a flashing/blank temperature display. This XPARTCO version is built with a quick-connect mounting clip, so it plugs in without cutting or splicing wires — unlike the genuine Whirlpool OEM part, which ships as a splice-in kit requiring you to cut the old thermistor's leads and join the new ones with included wire connectors. It directly replaces W10316760, WPW10323459, W10323459, 12791417, 12791417SP, 12791419SP, 1876627, W10280385, W10280386, W10308052, W10316760VP, W10438639, W10438761, W10452402, AH2580944, AP4538142, AWP40532, EA2580944, EAP2580944, PD00006590, PS2580944, and additional cross-reference numbers listed below. Installs in 15–30 minutes with basic hand tools. Quick Answer The XPARTCO W10316760 Refrigerator Thermistor Sensor fixes Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef refrigerators that are running warm, running constantly, freezing food unexpectedly, or showing a flashing/blank temperature display. This version uses a quick-connect clip — no wire cutting or splicing like the genuine Whirlpool splice-kit version requires. Replaces W10316760, WPW10323459, W10323459, 12791417, 12791417SP, 12791419SP, 1876627, W10280385, W10280386, W10308052, W10316760VP, W10438639, W10438761, W10452402, AH2580944, AP4538142, AWP40532, EA2580944, EAP2580944, PD00006590, PS2580944. Classic symptom: fridge or freezer running warmer than the setting, or running nonstop. Common Problems This Part Fixes Refrigerator or freezer running noticeably warmer than the temperature setting Fridge running constantly and never cycling off Temperature display flashing, showing dashes, or displaying an error code Food freezing in the fresh food compartment when it shouldn't be Compressor and fans not cycling normally, or running nonstop Inconsistent or swinging temperature readings on the display One compartment (fridge or freezer) running warm while the other stays normal Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator thermistor directly replaces the following OEM and cross-reference part numbers: W10316760, WPW10323459, W10323459, 12791417, 12791417SP, 12791419SP, 1876627, W10280385, W10280386, W10308052, W10316760VP, W10438639, W10438761, W10452402, AH2580944, AP4538142, AWP40532, EA2580944, EAP2580944, PD00006590, PS2580944 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermistor is used across a wide range of Whirlpool-built refrigerators from the following brands: Whirlpool refrigerators (including WRF535SMBM00, WRX735SDBM00, and related French door / side-by-side models) KitchenAid refrigerators (including KBFS22EWBL1, KBFS22EWMS1, KBFS22EWMS3, KBFS22EWMS5, KBFS22EWMS7, KBFS22EWWH1) Maytag refrigerators (select Whirlpool-built models, including KRFF302ESS) Jenn-Air refrigerators (select Whirlpool-built models, including MFI2269VEM) Amana refrigerators (select models) Inglis refrigerators (select models) Magic Chef refrigerators (select models) Note: Many of these refrigerators use separate thermistors for the fresh food and freezer compartments, so confirm which sensor location your model uses before ordering — appearance can be similar across positions. Always verify your appliance model number before ordering. Contact our support team with your model number if you're unsure. Key Features Direct-fit replacement refrigerator temperature thermistor — reports compartment temperature to the electronic control board Resolves "running warm," "running constantly," "freezing food," and "flashing display" symptoms caused by thermistor failure Quick-connect mounting clip — no wire cutting or splicing required Matches OEM electrical resistance curve for accurate temperature sensing Approximate lead length ~5 inches Replaces W10316760, WPW10323459, W10323459, 12791417, 12791417SP, 12791419SP, 1876627, W10280385, W10280386, W10308052, W10316760VP, W10438639, W10438761, W10452402, AH2580944, AP4538142, AWP40532, EA2580944, EAP2580944, PD00006590, PS2580944, and additional cross-reference numbers Compatible with Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef refrigerators Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number XPW10316760 OEM Part Number W10316760 Part Type Refrigerator Temperature Thermistor / Sensor Condition Aftermarket Replacement Application Whirlpool-Built Refrigerators (Fresh Food / Freezer Compartment) Mounting Quick-connect clip (no splicing) Approx. Lead Length ~5 inches (may vary by model) Compatible Brands Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, Magic Chef Installation Notes ⚠️ Disconnect Power Before Starting Unplug the refrigerator or shut off power at the breaker before accessing internal panels. Locate the thermistor at its mounting position inside the fresh food or freezer compartment (location varies by model — consult your model's parts diagram if unsure). Photograph the wire routing before disconnecting. On this XPARTCO version, simply unplug the old thermistor's connector from the wiring harness — no cutting or splicing needed. Release the old thermistor from its mounting clip or bracket and remove it. Install the new thermistor in the same position, securing it in its mounting clip. Plug the new thermistor's connector into the wiring harness, matching your photos. Reassemble any panels removed for access. Restore power and allow the refrigerator several hours to stabilize before checking temperatures. Tools needed: nut driver or screwdriver (for panel access), needle-nose pliers (for mounting clip). Frequently Asked Questions Is this the same as the genuine Whirlpool W10316760 thermistor? It's a direct-fit aftermarket equivalent, not the genuine Whirlpool part. The key functional difference is installation: the genuine OEM version ships as a splice-in kit requiring you to cut the old wires and use included splice connectors, while this XPARTCO version has a quick-connect clip that simply plugs in — no splicing tools needed. Will this fit my refrigerator? W10316760 and its cross-reference numbers span a wide range of Whirlpool-built models across several brands. Confirm fit using your refrigerator's exact model number before ordering, since visually similar thermistors are used across different platforms and compartment locations. Contact our support team with your model number if you're unsure. My fridge is warm but the freezer is fine (or vice versa) — could this part be the cause? Yes. Most of these refrigerators use separate thermistors for the fresh food and freezer compartments, so a single failed sensor can cause one section to run warm while the other stays normal. Confirm which sensor location your model uses before ordering. Do I need any tools to install this? Basic hand tools to access the interior panel (typically a nut driver or screwdriver) plus needle-nose pliers to release the old mounting clip. Because this version uses a plug-style connector, no wire strippers, cutters, or splice connectors are needed — unlike the genuine OEM splice-kit version. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical resistance curve, mounting position, and temperature-sensing function of the original W10316760 thermistor used in compatible Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

215846604 Genuine OEM Frigidaire Refrigerator Defrost Timer The 215846604 is a genuine Frigidaire OEM defrost timer, mounted inside the refrigerator near the top of the back wall. This timer is the scheduler for the defrost circuit: on a set cycle, it switches the refrigerator out of normal cooling mode and into a defrost mode, energizing the defrost heater long enough to melt any frost that has accumulated on the evaporator coil, then switches back to cooling once defrost is complete. This cycle repeats automatically for as long as the refrigerator runs, which is why a healthy timer is essential to preventing frost buildup in the first place. Rated 120V with a 6 hour, 21 minute cycle, measuring approximately 1.5"H x 3.2"L x 2.3"W. When this timer fails, the defrost heater never gets the signal — and the electrical energy — it needs to run, so frost keeps accumulating on the coil unchecked. A failing timer typically shows up as heavy frost or ice buildup on the evaporator coil, a freezer that runs too cold or too warm, or a refrigerator section that isn't cooling properly because ice-caked coils can't transfer heat efficiently anymore. It directly replaces AP2592907, 08003824, 08011620, 1748201, 241809401, 241809402, 442754, 5300541134, 5300800692, 5308003824, AH423802, EA423802, PS423802, and CC304. Quick Answer The 215846604 Genuine OEM Frigidaire Refrigerator Defrost Timer fixes Frigidaire, Kenmore, Crosley, Kelvinator, Gibson, Tappan, and Westinghouse refrigerators and freezers with heavy frost or ice buildup on the evaporator coil, a freezer running too warm or too cold, or a refrigerator section not cooling properly. 120V, 6 hour 21 minute defrost cycle. Replaces AP2592907, 08003824, 08011620, 1748201, 241809401, 241809402, 442754, 5300541134, 5300800692, 5308003824, AH423802, EA423802, PS423802, CC304. Before replacing, test the defrost thermostat and defrost heater with a multimeter — if both test good, the timer is the most likely faulty component. Common Problems This Part Fixes Heavy frost or ice buildup on the evaporator coil Freezer compartment running too cold or too warm Refrigerator section not cooling properly Refrigerator or freezer overheating Refrigerator running constantly as ice-caked coils reduce cooling efficiency Frost visible on interior walls or around the back panel Defrost heater not activating on its normal schedule Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator defrost timer directly replaces the following OEM and cross-reference part numbers: 215846604, 08003824, 08011620, 1748201, 241809401, 241809402, 29811-3, 442754, 5300541134, 5300800692, 5308003824, 54113-1, 54113-4, 55448-3, 55448-4, 55467-1, 8003824, AH423802, CC304, EA423802, F111812, G000158274, G000158291, G000173814, G000187005, G000187464, G158274, G163818, G169069, G173814, G174821, G178820, G185160, G187464, K1224661, K1224662, K1226501, K1226502, K1227229, K1227920, K1227927, K1228104, K1228105, K1230354, K1230534, K1233374, K1233375, NR00422503, R000422503, R000900129, R422503, W188C189A06, W188C189A07, WR422503, PD00005279, EAP423802, AP2592907, PS423802. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This defrost timer is compatible with select Frigidaire refrigerators and freezers, and also fits select Kenmore, Crosley, Kelvinator, Gibson, Tappan, and Westinghouse refrigerators and freezers built on the same Frigidaire/Electrolux platform. Note — not the same as 215846602: This timer runs a 6 hour, 21 minute defrost cycle. A similarly-numbered part, 215846602, runs a different cycle (6 hour, 40 minute) and replaces a separate set of numbers (215846606, 240371001, 241621501, AP2111929, PS423801). The two are not interchangeable. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which timer fits your refrigerator. Key Features Genuine Frigidaire OEM part — factory-specified cycle timing and switch contacts Automatically schedules the refrigerator's transition between cooling and defrost modes 6 hour, 21 minute defrost cycle Resolves "frost buildup on the coil," "freezer too cold or too warm," and "refrigerator not cooling" symptoms caused by timer failure Compact size: approximately 1.5"H x 3.2"L x 2.3"W Direct drop-in replacement — mounts to the original bracket with the same wiring harness connector Replaces AP2592907, 08003824, 08011620, 1748201, 241809401, 241809402, 442754, 5300541134, 5300800692, 5308003824, AH423802, EA423802, PS423802, and CC304 Compatible with Frigidaire, Kenmore, Crosley, Kelvinator, Gibson, Tappan, and Westinghouse refrigerators and freezers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 215846604 Part Type Refrigerator Defrost Timer Condition Genuine OEM Brand Frigidaire Voltage 120V Defrost Cycle 6 hours, 21 minutes Location Inside the refrigerator, near the top of the back wall Height 1.5 in. Length 3.2 in. Width 2.3 in. Weight Approx. 2.75 oz. Repair Difficulty Easy — basic tools required Quantity 1 defrost timer Compatible Brands Frigidaire, Kenmore, Crosley, Kelvinator, Gibson, Tappan, Westinghouse Installation Notes ⚠️ Unplug Refrigerator Before Starting Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. Locate the defrost timer control inside the refrigerator, typically near the top of the back wall — on some models it may be located behind a rear access panel or near the control housing instead, so check your specific model if it isn't immediately visible. Photograph the wiring harness connector before disconnecting anything. Use a screwdriver to remove the screws securing the timer in place, then carefully disconnect the wiring harness from the back of the old timer. Connect the wiring harness to the new 215846604 timer, matching the original connector orientation, and secure it in place with the mounting screws. Restore power and monitor the refrigerator over the next day to confirm the defrost cycle is running on schedule and frost is no longer accumulating excessively on the coil. Tools needed: screwdriver, work gloves. Frequently Asked Questions How do I know if the timer is actually the problem and not the defrost heater or thermostat? The defrost timer, defrost heater, and defrost thermostat all work together in the same circuit, so it's worth testing the other two before assuming the timer has failed. Test the defrost thermostat and the defrost heater with a multimeter — if both test as functioning properly, it's very likely the timer is the faulty component causing the defrost cycle not to run. There's heavy frost or ice on the coil. Is that definitely the timer? It's one of the most common causes. If the timer fails to advance into the defrost portion of its cycle, the heater never gets the signal or the power it needs to run, so frost keeps accumulating on the evaporator coil with nothing to melt it off. This is exactly the scenario this timer is designed to prevent when it's working correctly. What's the difference between 215846604 and 215846602? These are different timers with different cycle lengths — this 215846604 runs a 6 hour, 21 minute cycle, while 215846602 runs a 6 hour, 40 minute cycle and replaces a separate group of part numbers. They are not interchangeable, so always confirm which specific number your refrigerator's parts diagram calls for before ordering. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original cycle timing, switch contacts, and wiring harness configuration of the defrost timer originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3406107 Dryer Door Switch Replaces WP3406107 The XPARTCO 3406107 is an aftermarket replacement door switch for Whirlpool, Kenmore, Maytag, and KitchenAid dryers. Mounted inside the upper corner of the front panel, this safety switch has a spring-loaded black tab that gets pressed in when the door closes. That contact tells the control board the door is shut, which is required before the dryer will start, and it also powers the interior drum light. Over time the switch's internal contacts wear out or the tab loses spring tension, and the dryer either won't start at all or runs with the door open — a safety condition the switch is specifically designed to prevent. This is a three-wire SPDT (single pole, double throw) switch built to the same dimensions and mounting points as the original, and it's designed to remain compatible with older two-wire harnesses as well. Direct-fit aftermarket replacement, no wiring modifications needed. Quick Answer The XPARTCO 3406107 Dryer Door Switch fixes a dryer that won't start, runs with the door open, or has a dead interior light. Direct-fit replacement for OEM WP3406107. Classic symptom: pressing start does nothing until you push and hold the door shut, or the drum light never comes on. Common Problems This Part Fixes Dryer won't start even though the door is closed Dryer runs with the door open (safety switch failure) Interior drum light doesn't turn on Door doesn't seem to latch or seal properly against the switch tab Drum doesn't spin, or cycle stops intermittently Touchpad or start button appears unresponsive Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door switch directly replaces the following part numbers: WP3406107, WPW10569603, 3406107, 3406109, W10569603, 3405100, 3405101, 3406100, 3406101, ES6107, 528948, 11259-65, PD00002378, EAP11741701, AP6008561, AWP47183, PS11741701 This switch design was updated to a three-wire configuration at some point in its production history (superseding older 3405100/3405101/3406100/3406101 numbers), but the current three-wire version remains compatible with older two-wire harnesses, so it's a safe direct replacement across all of these part numbers. Compatibility This door switch is compatible with a wide range of Whirlpool, Kenmore, Maytag, and KitchenAid dryers, including units across the: Whirlpool/Kenmore Series 60, 70, 80, 90, 500, 600, 700, and 800 dryer lines AED4475TQ1, MEDC400VW0, and numerous additional model numbers Note: This switch has been used across a very wide range of Whirlpool-built dryers (including Kenmore, Maytag, and KitchenAid badged units) spanning many production years, so the list above is only a sample. Confirm your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering. Key Features Direct-fit aftermarket door safety switch for Whirlpool-built dryers Three-wire SPDT design, backward-compatible with two-wire harnesses Controls both the start-permission safety interlock and the interior drum light Resolves no-start, runs-with-door-open, and dead-light symptoms White plastic and metal tab construction, approx. 6.5" length Straightforward swap — typically 15–30 minutes with basic hand tools Product Specifications Part Number 3406107 OEM Part Number WP3406107 Part Type Dryer Door Safety Switch Condition Aftermarket Replacement Switch Type SPDT (Single Pole, Double Throw) Wire Configuration Three-Wire (Backward-Compatible with Two-Wire Harnesses) Length Approx. 6.5 Inches Color / Material White; Plastic & Metal Construction Application Whirlpool, Kenmore, Maytag & KitchenAid Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. The switch is mounted inside the upper corner of the front panel, so you'll need to remove the front panel or top panel per your model's service guide to access it. Disconnect the wire connector from the old switch, then remove the mounting screw(s) holding it in place. Install the new switch in the same position, reconnect the wire connector, and reinstall the panel. Before closing everything up, you can test the switch by pressing the black tab — you should feel spring resistance and hear or feel a distinct click. Restore power and confirm the dryer starts normally with the door closed and stops when the door is opened. Frequently Asked Questions My dryer won't start — is this the part I need? This is one of the most common causes of a dryer that won't start even with the door closed. Try pressing the black tab on the switch by hand — if it feels loose, doesn't click, or offers no resistance, the switch has likely failed and needs replacement. My dryer runs even with the door open — is that dangerous? Yes, this indicates the door safety switch has failed in a way that no longer prevents operation with the door open, which is a safety hazard. Replace the switch promptly and avoid running the dryer with the door open in the meantime. My dryer has a two-wire connector — will this three-wire switch still work? Yes. This switch was redesigned to a three-wire configuration but remains compatible with older two-wire wiring harnesses, so it's a safe direct replacement regardless of which wire configuration your dryer currently has. Does this switch also control the interior light? Yes. This switch serves a dual function — it's the safety interlock that permits the dryer to run only with the door closed, and it also powers the interior drum light when the door is open. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WR55X26671 Refrigerator LED Light Board The XPARTCO WR55X26671 is an aftermarket replacement LED light board compatible with select GE and Hotpoint refrigerators, commonly used in side-by-side and French door models. The LED light board sits behind the light lens inside the refrigerator or freezer compartment and provides interior illumination when the door is opened. It features 3 LED light clusters that deliver brighter, more energy-efficient lighting compared to traditional incandescent bulbs. When the light board fails, the refrigerator interior will be dark, making it difficult to see food contents. The board measures approximately 4" L x 3/8" W x 5/8" H with a white, yellow, and taupe plastic and metal construction. The surface is coated with three-proof paint to resist moisture damage from condensation inside the refrigerator. It directly replaces AP6035586, PS11767930, 4468532, EAP11767930, and PD00048392. Sold individually. Installs in under 5 minutes — no tools required in most cases. Quick Answer The XPARTCO WR55X26671 Refrigerator LED Light Board fixes GE and Hotpoint refrigerators where the interior light is out or flickering. LED board with 3 light clusters. Approx. 4" L x 3/8" W x 5/8" H. Moisture-resistant three-proof coating. Sold individually — some models use multiple boards in series. Replaces AP6035586, PS11767930, 4468532, EAP11767930. Compatible with GE side-by-side and French door refrigerators. Common Problems This Part Fixes Refrigerator interior light not working — compartment is dark when door is opened Freezer compartment light not working Interior light flickering or intermittently cutting out Only some LEDs on the light board working — partial illumination Light board visibly damaged, discolored, or burned Interior light stays dim after replacing the door switch (failed board, not switch) Replaces Part Numbers This LED light board directly replaces the following OEM and cross-reference part numbers: WR55X26671, 4468532, 225D9507G001, 57935, OT7849, W5B3Y3, AGE28912, EAP11767930, FIX11767930, PD00048392, AP6035586, PS11767930. Contact our support team with your model number if you need compatibility confirmation before ordering. Compatibility This LED light board is compatible with select refrigerators from the following brands: GE refrigerators — side-by-side models (GSS, GSE, DSE, CZS series and more) GE refrigerators — French door models (select models) Hotpoint refrigerators (select GE-platform models) Important: Some GE refrigerator models use multiple LED light boards wired in series. If your refrigerator has more than one light board, all boards in the series may need to be replaced at the same time — a single failed board in a series circuit can cause all boards on that circuit to go dark. Verify how many boards your model uses before ordering. Always verify your model number before ordering. Key Features 3 LED light clusters — brighter illumination than traditional incandescent bulbs with lower energy consumption Fits behind the light lens inside the refrigerator or freezer compartment — direct replacement for WR55X26671 Operates automatically with the door switch — lights when door opens, turns off when door closes Three-proof coating on the board surface — moisture, dust, and corrosion resistant for long service life inside the refrigerator Dimensions: approx. 4" L x 3/8" W x 5/8" H Sold individually — verify quantity needed for your model before ordering Ships in anti-static bag to protect sensitive electronic components during transit Aftermarket replacement built to OEM-equivalent quality standards Quick installation — under 5 minutes, no tools required in most cases Product Specifications Part Number WR55X26671 Part Type Refrigerator Interior LED Light Board Condition Aftermarket Replacement Application GE and Hotpoint side-by-side and French door refrigerators LED Clusters 3 light clusters per board Dimensions Approx. 4" L x 3/8" W x 5/8" H Color White / Yellow / Taupe Material Plastic / Metal Coating Three-proof paint (moisture, dust, corrosion resistant) Packaging Ships in anti-static bag Sold As Single board (some models require multiple — verify before ordering) Compatible Brands GE, Hotpoint Installation Notes ⚠️ Unplug Refrigerator Before Starting Unplug the refrigerator before beginning. Open the refrigerator door and locate the light lens cover inside the compartment. Gently pry off or unscrew the light lens cover to expose the light board behind it. Carefully disconnect the old light board from its electrical connector. Remove the old board and insert the new WR55X26671 in the same orientation, pressing it into its housing until it seats securely. Reconnect the electrical connector. Reinstall the light lens cover. Restore power and open the door to confirm the new light board illuminates correctly. Tools needed: None in most cases; a small flat-head screwdriver may help with the lens cover on some models. Frequently Asked Questions My refrigerator light is out — how do I know if it's the light board or the door switch? The easiest test is to manually press the door switch (the small button inside the door frame that the door presses when closed) — if pressing it causes the light to turn off and releasing it causes it to come back on, the door switch is functioning and the light board itself has failed. If pressing the door switch has no effect and the light remains off, the door switch may be faulty. You can also inspect the light board visually — if any LED clusters are visibly dark, discolored, or burned, the board has failed. My refrigerator uses multiple light boards — do I need to replace all of them? Possibly yes. Some GE refrigerator models wire their LED light boards in a series circuit, where all boards share the same electrical path. If one board in the series fails, it can break the circuit and cause all boards on that circuit to go dark — even boards that are otherwise still functional. If your refrigerator went completely dark in a compartment that uses multiple boards, it is recommended to replace all boards in that series at the same time rather than trying to identify and replace a single failed board. Is the WR55X26671 used in both the refrigerator and freezer sections? Yes — on compatible GE models, the same WR55X26671 light board is used in both the fresh food compartment and the freezer compartment. If the light is out in only one section, that section's board (or boards) has failed. If both sections are dark simultaneously, the issue may be with the door switch, main control board, or wiring rather than the light boards themselves. Why does the board ship in an anti-static bag? The WR55X26671 contains sensitive electronic components that can be permanently damaged by static electricity discharge during handling. The anti-static bag prevents static buildup during shipping and storage. When installing the board, avoid touching the circuit board traces or components directly — handle it by the edges or plastic frame. Do not open the anti-static bag until you are ready to install. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured with a three-proof moisture-resistant coating and to match the dimensions and performance of the original WR55X26671 LED light board. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3949247 Washer Lid Switch Replaces 3949247V The XPARTCO 3949247 is an aftermarket replacement lid switch assembly for Whirlpool top-load washers, and also fits select Roper, Estate, Kenmore, Inglis, Crosley, Amana, and KitchenAid models, including stacked washer/dryer laundry center units. This switch mounts to the underside of the cabinet top panel and tells the washing machine the lid is closed, allowing the wash cycle to begin. Black plastic with wire leads, sold individually. Over time, the plastic on the switch's actuator can become brittle with age and break when the lid is closed roughly, or from the movement of an unbalanced load causing parts of the washer to strike it. Symptoms of a failing lid switch include the wash cycle not starting even when the lid is closed, error codes related to the lid being open, inability to advance through cycle selections, or the washer not spinning while still agitating normally. It directly replaces 3949247V, 3949247, 3949237, 3949239, 3949240, 3949247VP, 4248251, TJ90ES247, AP3100003, ES247, AP5983746, AWP227261, EAP350434, OEM17951247, PD00024284, PS11722098. Quick Answer The XPARTCO 3949247 Washer Lid Switch fixes Whirlpool, Roper, Estate, Kenmore, Inglis, Crosley, Amana, and KitchenAid top-load washers (including laundry center combo units) that won't start with the lid closed, show lid-open error codes, won't advance through cycle selections, or agitate but won't spin. Black plastic, wire leads, sold individually. Replaces 3949247V, 3949247, 3949237, 3949239, 3949240, 3949247VP, 4248251, TJ90ES247, AP3100003, ES247, AP5983746, AWP227261, EAP350434, OEM17951247, PD00024284, PS11722098. Not the same as our 3949238 listing — these are separate, similarly-numbered switches used on different models. Common Problems This Part Fixes Wash cycle won't start even when the lid is closed Error codes related to the lid being open Inability to advance through cycle selections Washer agitates but won't spin Flashes or other improper lid switch behavior Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer lid switch directly replaces the following OEM and cross-reference part numbers: 3949247V, 3949247, 3949237, 3949239, 3949240, 3949247VP, 4248251, TJ90ES247, AP3100003, ES247, AP5983746, AWP227261, EAP350434, OEM17951247, PD00024284, PS11722098 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid switch is compatible with select Whirlpool top-load washers, and also fits select Roper, Estate, Kenmore, Inglis, Crosley, Amana, and KitchenAid washers built on the Whirlpool platform, including stacked washer/dryer laundry center units, and model numbers such as 11010202000, 11010202001, 11010502990, 11010502991, 11010852990, 11010852991, 11012202100, 11012502100, 11012852100, 11013202200, 11013212200, 11014102300, 11014112300, 11014202300, 11014212200, 11018202790, 11018522790, 11018522791, 11018532790, 11018542890, 11018542891, 11018609890, 11018702790, 11018702791, 11019101990, 11019101991, 11019101992, 11019202200, and 11020112000. Note — not the same as 3949238: Our 3949238 listing is a separate, similarly-numbered lid switch used on different models. Whirlpool also uses several other distinct lid switch designs, including the direct-drive style (8318084) and the thin-twin style (3355806), which are not interchangeable with this switch. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which switch your washer needs. Key Features Aftermarket replacement lid switch assembly — confirms the lid is closed before allowing the wash cycle to begin Resolves "won't start," "lid-open error codes," "can't advance cycle selections," and "agitates but won't spin" symptoms Black plastic construction with wire leads Mounts to the underside of the cabinet top panel Direct drop-in replacement matching the original mounting and connection Replaces 3949247V, 3949247, 3949237, 3949239, 3949240, 3949247VP, 4248251, TJ90ES247, AP3100003, ES247, AP5983746, AWP227261, EAP350434, OEM17951247, PD00024284, PS11722098 Compatible with Whirlpool, Roper, Estate, Kenmore, Inglis, Crosley, Amana, and KitchenAid washers, including laundry center units Aftermarket replacement built to OEM-equivalent quality standards Sold individually Product Specifications Part Number 3949247 OEM Part Number 3949247V Part Type Washer Lid Switch Assembly Condition Aftermarket Replacement Material plastic Wiring Wire leads Mounting Location Underside of cabinet top panel Function Confirms lid is closed before allowing the wash cycle to begin Repair Difficulty Easy — basic hand tools Quantity 1 lid switch (sold individually) Compatible Brands Whirlpool, Roper, Estate, Kenmore, Inglis, Crosley, Amana, KitchenAid Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting Unplug your washer from the wall outlet and turn off the water supply before beginning. Wear work gloves. Remove the screws holding the access panel in place at the back of the machine, then carefully remove the panel and set it aside. Locate the lid switch assembly near the top, center of the washer's interior. Use a Phillips and flathead screwdriver to unscrew the three screws that hold the lid switch assembly in place. Disconnect the wire harness from the old lid switch and carefully remove it from the machine. Install the new 3949247 into the machine in the exact same manner the old switch was removed. Connect the wire harness to the new switch. Reattach the three screws to secure the switch in place. Replace the access panel and reattach its screws. Turn on the water supply and plug in the washer. Run a test cycle with the lid closed to confirm the washer starts and spins normally. Tools needed: Phillips head screwdriver, flat head screwdriver. Frequently Asked Questions My washer agitates but won't spin. Is this the part I need? Yes, this is a well-documented symptom of a failed lid switch. This switch tells the washer's control system that the lid is closed before allowing certain functions, and spin specifically often requires this signal — a failed switch commonly leaves agitation working while blocking spin. Why does this switch fail over time? The plastic on the switch's actuator can become brittle with age and break when the lid is closed roughly. It can also break from the movement of an unbalanced load causing parts of the washer to strike it during a cycle. Is this the same as the 3949238 switch? No, these are separate lid switch part numbers, despite the similar numbering. Our 3949238 listing is used on different models. Always confirm your exact part number from your washer's parts diagram or the sticker on your old switch before ordering. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the material, wiring, and switching function of the original 3949247V lid switch assembly used in compatible Whirlpool, Roper, Estate, Kenmore, Inglis, Crosley, Amana, and KitchenAid washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine Whirlpool OEM Whirlpool WPW10184813 Refrigerator Genuine OEM Ice Dispenser Motor Genuine OEM ice-dispenser door motor for select Whirlpool-built refrigerators. Product Overview The Whirlpool WPW10184813 Refrigerator Ice Dispenser Door Motor is a Genuine Whirlpool OEM replacement part. It opens and closes the ice chute door during dispenser operation so ice can pass through the chute and the door can reseal afterward. A failed motor can cause the dispenser door to remain stuck open or closed, prevent ice from dispensing correctly, or allow warm room air to enter the chute area. Quick Answer WPW10184813 is the Genuine Whirlpool OEM ice-dispenser door motor that replaces W10184813 and 2305262. Verify the complete refrigerator model number before purchase. Common Problems This Part May Fix Ice dispenser door will not open Ice chute door will not close Ice maker makes ice but ice will not dispense Chute door sticks or operates intermittently Warm air enters around the dispenser chute Frost or moisture develops around the dispenser opening Replaces and Cross-References WPW10184813, 1489085, 2305262, AP6016508, EAP11749796, W10184813, AWP49407, OEM18049533, PD00006398, PS11749796 Cross-reference numbers are provided for identification. Always verify compatibility by complete refrigerator model number. Compatibility Used on select Whirlpool-built refrigerators sold under Whirlpool, KitchenAid, JennAir, Maytag, and Kenmore brand names. Compatible model examples include: GI7FVCXWY00 KSCS25FTMS02 KSRS25FTSS01 KSCS23FVMS02 KSRS25RSBT01 KSCS25FVMS01 KSCS25FTSS00 GC3NHAXVA00 106.56702500 Important: This is only a partial model list. Confirm the complete model number from the refrigerator identification label before ordering. Key Features Genuine Whirlpool OEM part Operates the ice dispenser chute door Replaces W10184813 and 2305262 For select Whirlpool-built side-by-side and French-door refrigerators Helps restore proper dispenser-door opening and closing Product Specifications Manufacturer Part Number WPW10184813 Brand Whirlpool Part Type Refrigerator Ice Dispenser Door Motor Condition New Quality Genuine OEM Application Ice Dispenser Chute Door Package Quantity 1 Motor Installation Notes Disconnect refrigerator power before service. Remove the dispenser trim and front components according to the appliance service procedure. Photograph connector and mechanical linkage positions before disassembly. Inspect the chute door, hinge, spring, and linkage for binding or damage before replacing the motor. Transfer or reconnect the wiring and linkage exactly as originally installed. Reassemble all dispenser parts and verify the chute door opens and fully closes before returning the refrigerator to service. Diagnostic tip: A dispenser that will not release ice can also be caused by an actuator, dispenser switch, control board, auger motor, frozen chute, or mechanical obstruction. Diagnose the dispenser system before replacing parts. Frequently Asked Questions Is WPW10184813 a Genuine Whirlpool OEM part? Yes. WPW10184813 is a Genuine Whirlpool OEM ice-dispenser door motor. Does it replace W10184813? Yes. Whirlpool lists WPW10184813 as the replacement for W10184813 and 2305262. What does this motor do? It opens and closes the dispenser chute door so ice can pass through the chute and the opening can reseal after dispensing. Will it fit every Whirlpool refrigerator? No. Verify the complete refrigerator model number before ordering because dispenser designs vary by model and production revision. Shop With Confidence Genuine Whirlpool OEM replacement part. Verify your complete refrigerator model and original part number before ordering. Genuine OEMIce Dispenser MotorCompatibility SupportFast U.S. Shipping

Read more less

Genuine OEM EBF61674802 Washer Lid Switch and Lock Assembly The Genuine OEM LG EBF61674802 is the lid switch and lock assembly for select LG and Kenmore top-load washers. The assembly includes the switch mechanism and a connecting wire that links the lid latch to the washer's electrical system. The switch tells the washer the lid is latched so a cycle can start, and the lock keeps the lid closed during the cycle. When it fails, the washer may not start, the lid may not latch or lock, or the washer may show a DL error code. This is the original LG part, not an aftermarket equivalent. It is sold individually. Check your model number before ordering. Quick Answer The Genuine OEM EBF61674802 Lid Switch and Lock Assembly replaces the lid switch and lock on a compatible LG or Kenmore top-load washer when it has failed. Replaces EBF60665201, EBF61674801, EBF61674804 and TAW36158136. Classic symptoms: the washer won't start, the lid won't latch or lock, or a DL error code appears. Common Problems This Part Fixes Washer won't start Lid won't close or latch Lid locking problems, including a lock stuck in the locked position DL error code Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This lid switch and lock assembly replaces or supersedes the following part numbers: EBF61674802, EBF60665201, EBF61674801, EBF61674804, TAW36158136, 2025745, 2703681, 4877523, ALG54727, AP5210199, EAP8751171, PD00023037, PS8751171 If your old assembly shows a different number, contact our support team and we'll check whether it matches. Compatibility This lid switch and lock assembly is listed for LG and Kenmore top-load washers, including these examples: LG 25667, 29002, 31553, 31623, WT5270CW, WT7700HVA LG WT7200CV/00, WT7300CW/00, WT7100CW/00 Kenmore 79629272001, 79629002000, 79629472000, 79631512210 Note: The models above are a sample of roughly 30 that retailers list, not a full list. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM LG part, not an aftermarket equivalent Includes the switch mechanism and connecting wire to the lid latch Tells the washer the lid is latched so a cycle can start Sold individually Product Specifications Part Number EBF61674802 OEM Part Number EBF61674802 Part Type Washer Lid Switch and Lock Assembly Condition Genuine OEM Manufacturer LG Quantity 1 Assembly Application Select LG and Kenmore Top-Load Washers Installation Notes ⚠️ Disconnect Power And Water Before Installing Unplug the washer and turn off the water supply before you begin. Remove the access panel per your model's service guide, note how the wire connector attaches, and disconnect it. Remove the old assembly, snap the new assembly into place, and reconnect the wire. Refit the panel, restore power and water, and test that the lid latches and the washer starts. Frequently Asked Questions My washer shows a DL error or won't start. Is this the part I need? It can be. Check the wiring first, then the lid switch and lock. Other parts, such as the control board, can cause similar symptoms, so confirm the lock assembly is the problem before replacing it. Is this an OEM or aftermarket part? This is a genuine OEM part from LG, not an aftermarket equivalent. Is this for top-load or front-load washers? It is listed for top-load washers. For any other washer type, match the part number and your model number, or contact our support team. Will this fit my washer? It is listed for about 30 LG and Kenmore models, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

242252702 Genuine OEM Frigidaire Refrigerator Water Valve The 242252702 is a genuine Frigidaire OEM triple-solenoid water inlet valve assembly for Frigidaire, Electrolux, Kenmore, Crosley, and White-Westinghouse side-by-side refrigerators. This valve is the central control point where your home's water supply connects to the refrigerator, and it manages water flow to both the ice maker and the door-mounted water dispenser through three separate solenoids housed in one assembly, each opening independently depending on what's being called for. Rated 120V, 50/60Hz per solenoid (20W maroon, 20W yellow, 35W green — each solenoid's wire is color-coded), this valve has 4 outlets total: one 1/4" tube inlet, three 5/16" tube outlets, and one 1/4" tube outlet. It measures approximately 7-1/8"L x 3-3/4"W x 3-1/4"H and ships as a complete assembly with mounting bracket and installation instructions. This valve directly replaces the older 241734302 design and uses updated quick-connect fittings in place of the older screw-on style. A failing valve typically shows up as the ice maker or dispenser not working, slow water flow, or — notably — an overflowing ice maker caused by the valve not shutting off completely if household water pressure is too low. It directly replaces 240321801, 240505101, 240505102, 240508101, 240508102, 240531101, 241734301, 241734302, 7241734301, WV2702, 2692163, AP5671757, EAP7784018, PD00000153, PS7784018, and K-76150. Quick Answer The 242252702 Genuine OEM Frigidaire Refrigerator Water Valve fixes Frigidaire, Electrolux, Kenmore, Crosley, and White-Westinghouse side-by-side refrigerators where the ice maker or water dispenser isn't working, water flow is slow, or the ice maker is overflowing. Triple-solenoid, 4-outlet valve assembly with bracket. Replaces 240321801, 240505101, 240505102, 240508101, 240508102, 240531101, 241734301, 241734302, 7241734301, WV2702, 2692163, AP5671757, EAP7784018, PD00000153, PS7784018, K-76150. This valve needs at least 20 psi of household water pressure to shut off completely — if pressure is too low, the valve can leak and cause the ice maker to overflow even when the valve itself is functioning correctly. Common Problems This Part Fixes Ice maker has stopped making ice, or is producing less ice than usual Water dispenser on the refrigerator door isn't working or has slowed down Ice maker overflowing or leaking Slow water flow at the dispenser Water leaking near the valve at the back of the refrigerator Error code related to the water system displayed on some models Cracked or physically damaged valve housing Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator water valve directly replaces the following OEM and cross-reference part numbers: 242252702, 240321801, 240505101, 240505102, 240508101, 240508102, 240531101, 241734301, 241734302, 2692163, 7241734301, PD00000153, EAP7784018, AP5671757, AFR15932, PS7784018 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select Frigidaire side-by-side refrigerators, and also fits select Electrolux, Kenmore, Crosley, and White-Westinghouse refrigerators built on the same platform, including model numbers such as: BFHS2611LM, BFHS2611LM0 BGHS2634KE0, BGHS2634KE1, BGHS2634KP0, BGHS2634KP1, BGHS2644KF0, BGHS2644KF1 FFSS2615TS0, FFSS2615TE4, FFHS2611PFEA, FFHB2750TD5, FRSS26L3AF0 FRS26H5ASB4, FRS26H5ASB5, FRS26H5ASB8, FRS26H5ASBA, FRS26R2AW6, FRS26R4AW5, FRS26R4CB1, FRS26RLECS0, FRS26LF7DS7 FRS6LR5EB3, FRS6LR5EB6, FRS6LR5EM2, FRS6LR5EM8, FRS6R5ESB4 PLHS69EESS2, PLHS69EGSS1, PLHS269ZCB4, PHSC39EGSS0 Crosley CRSE234FB2 Note: This valve's fitting style has been updated to quick-connect fittings, replacing the older screw-on style used on some earlier units — this may cause the appearance to differ slightly from your original part, but it is a correct functional replacement. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified solenoid design and flow-rate calibration Triple-solenoid assembly supplies water to both the ice maker and door water dispenser Resolves "ice maker not working," "dispenser not working," "slow water flow," and "ice maker overflowing" symptoms Color-coded solenoid wiring (maroon, yellow, green) for straightforward reconnection 4 outlets: 1x 1/4" tube inlet, 3x 5/16" tube outlets, 1x 1/4" tube outlet Updated quick-connect fittings for easier installation than older screw-on designs Ships complete with mounting bracket and installation instructions Replaces the full cross-reference list above, including the older 241734302 design Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 242252702 Part Type Refrigerator Water Inlet Valve (Triple Solenoid) Condition Genuine OEM Brand Frigidaire Application Side-by-Side Refrigerators Voltage 120V per solenoid Frequency 50/60 Hz per solenoid Wattage 20W (maroon), 20W (yellow), 35W (green) Outlets 1x 1/4" tube inlet, 3x 5/16" tube outlets, 1x 1/4" tube outlet Dimensions 7-1/8"L x 3-3/4"W x 3-1/4"H Weight Approx. 1.08 lbs. Minimum Water Pressure 20 psi (required to shut off fully) Kit Contents Valve assembly, mounting bracket, installation instructions Color Gray / Blue / Green / Yellow / Maroon Material Plastic / Metal Quantity 1 valve assembly Compatible Brands Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse Installation Notes ⚠️ Unplug Refrigerator And Shut Off Water Supply Before Starting Disconnect power at the outlet and shut off the water supply before beginning. Wear work gloves. Pull the refrigerator away from the wall for access, then locate the valve at the rear of the cabinet. Remove the two hex screws securing the old valve. Before disconnecting anything, note or photograph which plastic tube connects to which port on the multi-port valve assembly — with three solenoids and multiple outlets, getting a hose on the wrong port will send water to the wrong place. Disconnect the water supply hose, the electrical connectors (which are color-coded to their matching solenoids on the new valve), and the outlet hoses, then remove the old valve. Install the new 242252702 in the same position with its included mounting bracket, secure it with the hex screws, and reconnect each outlet hose to its correct port exactly as noted. Reconnect the color-coded electrical connectors to their matching solenoid wires. Reattach the water supply hose, tightening securely. While the back of the refrigerator is accessible, it's also a good opportunity to clean the condenser coils and surrounding area. Restore the water supply and check every connection for leaks before restoring power. Push the refrigerator back into place, then test both the ice maker and water dispenser over the following day. Tools needed: hex screwdriver or nut driver, pliers, work gloves. Frequently Asked Questions My ice maker is overflowing. Is this the valve? Possibly, but check your household water pressure first. This valve requires a minimum of 20 psi to shut off fully — if your home's water pressure is below that, the valve may not close completely even though it's functioning correctly, letting water leak through and overflow the ice maker. If your water pressure tests below 20 psi, that's the underlying cause rather than a defective valve, and addressing the pressure issue (or installing a pressure-boosting solution) is the correct fix. The new valve looks different from my old one. Is that normal? Yes. This valve has been updated to use quick-connect fittings in place of the older screw-on style used on earlier units, so the connection points may look different from what you're used to. It's still a correct, direct functional replacement — the new fittings just make installation somewhat easier. How do I know which hose goes where? This valve has multiple outlets. Note or photograph the hose routing on your old valve before disconnecting anything — with three solenoids and four total outlets, it's easy to reverse a connection if you're not careful. The electrical connectors are color-coded (maroon, yellow, green) to help you match them to the correct solenoid on the new valve, which makes the wiring side more foolproof than the hose routing. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original triple-solenoid design, wattage per solenoid, and outlet configuration of the water valve originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WB24X10146 Microwave Door Switch The XPARTCO WB24X10146 is an aftermarket replacement micro switch (also called a door interlock switch) compatible with a wide range of GE, Hotpoint, RCA, Kenmore, and Sears over-the-range and countertop microwaves. This is a "stand on" style normally-open (NO) interlock switch, identified by the internal designation KW3A-NO, that mounts near the door latch and only closes its circuit when the door is fully shut and latched. The control board reads this switch as part of a multi-switch safety interlock chain that confirms the door is secure before allowing the magnetron to energize. When this switch fails, the microwave commonly won't start at all, trips a door-related error code, or in rare cases can allow the unit to run with the door not fully secured — which is a safety-relevant fault, not just a convenience one. It directly replaces WB24X10146, WB24X28941, MW-7100-33, AGE22794, AH1019163, AP3866977, 1166990, EA1019163, EAP1019163, PD00039881, PS1019163. Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO WB24X10146 Microwave Door Switch fixes GE, Hotpoint, RCA, and Kenmore/Sears microwaves that won't start, display a door-related error code, or have a door that doesn't reliably confirm as closed. Normally-open (NO) "stand on" interlock switch, rated 250VAC / 16A, with 0.187" (4.7mm) quick-connect terminals. Replaces WB24X10146, WB24X28941, MW-7100-33, AGE22794, AH1019163, AP3866977, 1166990, EA1019163, EAP1019163, PD00039881, PS1019163. Classic symptom: turntable light and display work, but pressing Start does nothing. Common Problems This Part Fixes Microwave won't start when Start is pressed, even though the display and light work Door-related error code or fault light on the display Microwave randomly shuts off mid-cycle Door feels like it isn't latching or registering as closed Clicking sound from the door area with no response from the microwave Intermittent operation that seems tied to how hard the door is closed ⚠ Safety-Relevant Component Door interlock switches are safety components that prevent the magnetron from energizing unless the door is fully closed and latched. Never bypass, jumper, or defeat a microwave door switch to "get it working" — doing so can allow microwave energy to leak while the door is open, which is a genuine radiation safety hazard. Always disconnect power before servicing, and replace all interlock switches in the chain if more than one shows signs of wear. Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This microwave door switch directly replaces the following OEM and cross-reference part numbers: WB24X10146, WB24X28941, MW-7100-33, AGE22794, AH1019163, AP3866977, 1166990, EA1019163, EAP1019163, PD00039881, PS1019163 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is compatible with a wide range of GE-built microwaves across the following brands: GE over-the-range and countertop microwaves (JVM, PVM, and CEB series, including JEM3072DH1BB, JEM3072SH1SS, JNM3161DF2BB, and CCWK15C1W1DS/SS) Hotpoint microwaves (GE-built models) RCA microwaves (GE-built models) Kenmore and Sears microwaves (select GE-built models) Note: Do not confuse this with the similarly styled EXP499/EXP497 microwave door switches, which also use 4.7mm terminals but are not the same switch. WB24X10146 is a "stand on" style switch specific to GE's own interlock design — always match by part number, not terminal size alone. Always verify your appliance model number before ordering. Key Features Normally-open (NO) "stand on" door interlock switch, internal designation KW3A-NO Resolves "won't start," "door error code," and "shuts off mid-cycle" symptoms caused by interlock switch failure Rated 250VAC / 16A for reliable switching under microwave load 0.187" (4.7mm) quick-connect terminals for a secure wire connection Direct-fit mounting to match the original interlock bracket Replaces WB24X10146, WB24X28941, MW-7100-33, AGE22794, AH1019163, AP3866977, 1166990, EA1019163, EAP1019163, PD00039881, PS1019163 Compatible with GE, Hotpoint, RCA, Kenmore, and Sears microwaves across dozens of models Aftermarket replacement built to OEM-equivalent quality and safety standards Product Specifications Part Number XPWB24X10146 OEM Part Number WB24X10146 Part Type Microwave Door Interlock Switch ("Stand On" / KW3A-NO) Condition Aftermarket Replacement Switch Type Normally Open (NO) Voltage Rating 250VAC Current Rating 16A Terminal Width 0.187" (4.7mm) Compatible Brands GE, Hotpoint, RCA, Kenmore, Sears Installation Notes ⚠️ Unplug Microwave Before Starting Disconnect power at the outlet, and for built-in/over-the-range units also switch off the dedicated circuit breaker — microwaves store high voltage in the capacitor even after unplugging. Remove the outer cabinet or control panel cover to access the door switch assembly near the latch mechanism. Photograph the wiring before disconnecting, since GE microwaves typically use two or three interlock switches wired in sequence and mixing up the connections can leave the unit unsafe to operate. Disconnect the quick-connect terminals from the old switch, noting which wire goes to which terminal. Remove the mounting screw(s) holding the switch to its bracket and remove the old switch. Install the new WB24X10146 in the same position and secure it with the mounting screw(s). Reconnect the terminals exactly as photographed. Reassemble the cabinet or panel, restore power, and test that the door registers correctly and the microwave starts normally. Tools needed: Phillips screwdriver, nut driver (for cabinet screws). Frequently Asked Questions My microwave's display and turntable light work, but it won't start — is this the part? This is a classic symptom of a failed door interlock switch. The control board needs a confirmed "door closed and latched" signal from all switches in the interlock chain before it will energize the magnetron. If that signal is missing from even one switch, most GE microwaves will power up normally but refuse to start a cook cycle. Confirm with a multimeter continuity test on the suspect switch before ordering, since GE microwaves usually use more than one interlock switch. Is this the same as the EXP499 or EXP497 microwave door switch? No — while all three use similar 4.7mm terminals, they are different switches used in different microwave platforms and are not interchangeable. WB24X10146 is GE's own "stand on" KW3A-NO design. Always match by part number rather than terminal size or general appearance. Is it safe to keep using the microwave if I suspect this switch is bad? We'd recommend not continuing to use it until it's repaired. Door interlock switches exist specifically to prevent microwave energy from leaking out while the door is open or not fully latched. If a switch is failing intermittently, the microwave may seem to work sometimes, but that's not a reason to keep using it — replace the switch before further use, and never attempt to bypass or jumper an interlock switch. How many interlock switches does my GE microwave have, and do I need to replace them all? Most GE microwaves use two or three interlock switches wired in sequence (often a primary switch, a secondary/monitor switch, and sometimes a door sensing switch). You typically only need to replace the specific switch that's testing bad, but if one has failed from age or wear, the others are often not far behind — some technicians replace the full set at once to avoid a repeat repair call. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

DC34-00025G Washer Genuine OEM Lid Switch and Lock Assembly – Fits Samsung Washers Product Overview The DC34-00025G Washer Lid Switch and Lock Assembly is a genuine OEM replacement part that ensures your washer lid stays securely locked during wash and spin cycles. This part detects when the lid is closed and locks it to prevent accidental opening, providing safety and proper cycle operation. A worn or broken lid lock can cause your washer to stop mid-cycle, display error codes, or fail to start. Replacing it restores dependable washer performance and safety compliance. Replaces Part Numbers This lid switch and lock assembly replaces DC34-00025G, AP6884125, PS12720530. Manufactured to original equipment specifications for a precise fit and long-term durability. Compatible Brands Compatible with select Samsung top-load washers manufactured by Samsung. Fits a variety of models using this specific lid lock assembly. Fixes the Following Issues Washer won’t start or stops mid-cycle Lid doesn’t lock properly Error codes related to lid switch or lock failure Washer won't enter spin or drain cycles Why Buy from Parts‑O‑Matic Factory-original genuine OEM part Fast and free U.S. shipping Trusted by appliance professionals and DIYers Backed by reliable customer support

Read more less

Genuine Whirlpool WPW10392132 Refrigerator Defrost Thermostat - Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Amana Product Description Maintain optimal cooling with the Genuine Whirlpool WPW10392132 Refrigerator Defrost Thermostat. This OEM defrost thermostat is designed for select Whirlpool, Kenmore, KitchenAid, Maytag, and Amana refrigerators, monitoring evaporator coil temperature to regulate the defrost cycle, preventing frost buildup and ensuring efficient cooling. It addresses issues like frost accumulation, warm refrigerator temperatures, or freezer not cooling properly, delivering reliable performance as an authentic Whirlpool part. Note: Includes one defrost thermostat with two-wire connector. Disconnect power before installation. Check defrost heater and related components for optimal performance. Replaces part numbers: WPW10392132, AP6020798, W10392132, PD00028150, EAP11754118, 2118359, PS11754118. Compatibility: Compatible with models including but not limited to: Whirlpool: ED5FVGXWS00, ED5VHGXMB10, ED5VHGXML10, GD5DHAXVY00, WRS325FDAM02 Kenmore: 106.51132210, 106.51133210, 106.51173310 KitchenAid: KSRJ25FXMS00, KSRL25FXMT00 Maytag: MSD2559XEM01, MFI2569VEM10 Amana: ASD2522WRB02, ASD2522WRW01 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, KitchenAid, Maytag, and Amana refrigerators. ❄️ Specifications: OEM defrost thermostat, two-wire connector. 💪 Reliable Performance: Authentic Whirlpool part ensures long-lasting durability. 🛠️ Easy Installation: Requires screwdriver, pliers, work gloves; typically installed in 20–30 minutes. 🛡️ Effective Fixes: Resolves frost buildup, warm refrigerator temperatures, or freezer not cooling properly. Product Specification Part Number: Genuine Whirlpool WPW10392132 Component Type: Refrigerator defrost thermostat Material: Metal and plastic with sealed sensor Electrical Specs: 120V compatible Mounting: Clip-mounted on evaporator coil Operating Conditions: Suitable for low-temperature refrigerator environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the refrigerator from the power source before installation. Shop for high-quality Genuine appliance parts with a 30-day return policy. Keep your refrigerator cooling efficiently today! Add to cart now for a reliable fix!

Read more less