Search results for "washer switch"

WP661566 Dishwasher Genuine High Limit Thermostat Replaces Part Number: WP661566, 661566, W10339474, 2887, 3369777, 3370783, 3371618, 4171694, WP661566VP, AP6010246, PS11743423. Description: The High Limit Thermostat is a Genuine OEM part for specific Kenmore, Whirlpool dishwasher models. This safety feature is designed to prevent the dishwasher from overheating by shutting off the power if the internal temperature exceeds a certain limit. It acts as a safeguard against potential hazards, such as fires, and ensures the dishwasher operates within safe temperature ranges.   

Read more less

EXPW79SC (4 Pack) Washing Machine Fill Hose Gasket with Screen 4 Pack compatible with 5/ 8 inch washing machine and 3/4 inch garden hose Fine Screen the rubber washer with stainless steel filter mesh, serves as a flow restrictor can reduce the waste of water effectively     

Read more less

21366 Washer Spanner Nut Replaces WP21366 Replaces Part Numbers: WP21366, 21366, 16060, LP331, AP6005824, PS11738884.

Read more less

154825001 Genuine OEM Frigidaire Dishwasher Heating Element The 154825001 is a genuine Frigidaire OEM round heating element that sits exposed at the bottom of the dishwasher tub. Unlike a hidden element concealed beneath the tub floor, this is a visible ring-shaped element you can see sitting right in the bottom of the wash chamber. It serves two jobs: it heats the wash water to the temperature needed to properly dissolve detergent and break down grease and food soil, and at the end of the cycle it provides the heat that drives the drying phase, helping moisture evaporate off your dishes rather than leaving them wet. Mounted through a 0.98" hole with two mounting nuts and connected by two wire terminals, this element carries a pair of white alignment dots that must line up with the tub's retaining clips during installation. Over time, mineral buildup from hard water, general corrosion, or simple electrical wear can cause the element to fail. A failing or dead element produces a specific and recognizable pattern: water never gets hot enough to clean effectively, dishes come out wet at the end of the cycle instead of dry, and the whole cycle may run noticeably longer as the dishwasher's control tries to compensate. It directly replaces AP5628696, 154482901, 154663801, 2308825, PS3653449, and EAP3653449. As a genuine OEM part, the 154825001 is manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. Quick Answer The 154825001 Genuine OEM Frigidaire Dishwasher Heating Element fixes Frigidaire, Kenmore, Electrolux, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse dishwashers with dishes that don't get properly clean, dishes that come out wet instead of dry, or cycles that take longer than they used to. Exposed round heating element, 0.98" mounting hole, 2 wire terminals. Replaces AP5628696, 154482901, 154663801, 2308825, PS3653449, EAP3653449. Before replacing, test the old element with a multimeter for resistance — a bad control board relay can produce identical symptoms with a perfectly good element. Common Problems This Part Fixes Dishes not getting properly clean because wash water isn't reaching the correct temperature Dishwasher not drying dishes — items come out wet at the end of the cycle Cycle taking noticeably longer than usual to complete Visible damage, corrosion, or discoloration on the element itself Element that doesn't glow or heat up when the wash cycle is running Water leaking near the high-temperature wire connector at the element terminals Mineral scale buildup visible on or around the element Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher heating element directly replaces the following OEM and cross-reference part numbers: 154825001, 154482901, 154663801, 2308825, AP5628696, AFR14520, EAP3653449, PD00000951, PS3653449. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This heating element is compatible with select Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse dishwashers, spanning a wide range of model series including BBBD, BGBD, BGHD, DGBD, DGCD, DGHD, FDB, FDBB, FDBD, FFBD, FFID, FGBD, FGCD, FGHD, FGID, FPHD, FPID, GLD, GSB, LEDB, LFBD, LFID, LGBD, LGHD, and PLD. Verified model numbers include: FFCD2413UW1A, FGID2466QF4A, FGID2466QF5A, FFID2426TD1A, FGBD2438PF4A, FGHD2465NF1A, FGHD2433KF1, LFID2426TF1A, LFID2422RF0A, LFID2422RF3B, LFID2422RF4B, LFID2426TF4A, LFID2426TF5A, LGBD2431LF0A, LGBD2431NF0B, LGBD2431NF1B, LGBD2432LW0A, LGBD2432LW0B, and CDB350/CDB500/CDB900 series models. Also fits Kenmore 587-series, Crosley CBD-series, Kelvinator KADB240, and White-Westinghouse WWBD2400 dishwashers. Note: This is an exposed round heating element sitting visibly in the bottom of the tub, not a hidden element mounted underneath. It is not interchangeable with hidden/concealed heating elements used on other dishwasher platforms. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified heating output and terminal configuration Exposed round design sits in the tub bottom for direct water heating and drying support Resolves "not cleaning properly," "not drying," and "cycle taking too long" symptoms caused by element failure 0.98" mounting hole with two mounting nuts and wire terminals Two white alignment dots for correct positioning in the tub's retaining clips Direct drop-in replacement — no modification required Replaces 154482901, 154663801, 2308825, AP5628696, PS3653449, and EAP3653449 Compatible with Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 154825001 Part Type Dishwasher Round Heating Element (Exposed) Condition Genuine OEM Brand Frigidaire / Electrolux Location Bottom of the wash tub (exposed, visible) Mounting Hole 0.98 in. Terminals 2 wire connections + 2 mounting nuts Alignment 2 white dots must align with tub retaining clips Repair Difficulty Medium — basic dishwasher familiarity required Tools Required Screwdrivers, wrench set Quantity 1 heating element Compatible Brands Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, Westinghouse Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Before Starting — Handle The Element Carefully Disconnect power at the circuit breaker and shut off the water supply before beginning. Wear work gloves. On many models you'll need to pull the dishwasher out from under the counter to access the undercarriage — remove the two screws securing the unit to the counter first. Remove the lower rack and the lower spray arm (it typically pushes down and twists to unlock) to access the element inside the tub. From underneath, disconnect the two wires from the element's terminals and remove the two mounting nuts with a 1/2" wrench, taking care not to overtighten when you reach the new element — over-torquing can crush the sealing washers and cause a leak at the connector. Lift the old element free from its retaining clips inside the tub. To install the new 154825001, locate the two white alignment dots on the element and position them so they slide into the tub's retaining clips correctly — this ensures the element seats in its proper orientation. Push the terminals down through the mounting hole, then from underneath, reinstall and tighten the mounting nuts snugly but not excessively. Reconnect the two wires to the terminals, reinstall the lower spray arm and press it down to lock it in place, and reinstall the lower rack. Restore water and power, then slide the dishwasher back into place and secure it to the counter with its mounting screws. Run a test cycle and check underneath for any leaks at the element connection before considering the repair complete. Tools needed: screwdriver, 1/2" wrench, work gloves. Frequently Asked Questions How do I know it's the heating element and not something else, like the control board? Before replacing the element, it's worth testing it with a multimeter for resistance — a healthy element typically reads in the neighborhood of 14 ohms, though exact values vary by model. If the old element tests fine but dishes still aren't drying or getting hot enough, the more likely cause is upstream of the element itself, such as a control board relay that isn't sending power to it correctly. Some owners have replaced a perfectly good element only to find the actual fault was a bad solder connection on the control board relay — testing first can save you an unnecessary purchase. Can I clean the element instead of replacing it? Light surface cleaning to remove mineral scale buildup is reasonable and can sometimes help if reduced heating output is due to scale insulating the element. However, if the element tests as an open circuit (no continuity) or shows visible damage, cracking, or corrosion through the metal sheath, cleaning won't restore it — replacement is the correct fix at that point. I noticed water leaking near the element's wire connector. Is that related? Yes, this is a documented failure point on this element design — the high-temperature wire connector at the terminals can develop a leak, especially if the mounting nuts were overtightened during a prior installation and damaged the sealing washer. When installing the new element, tighten the mounting nuts snugly but avoid excessive force, which helps prevent this same leak point from recurring. Do I really need to pull the dishwasher out from under the counter? On most installations, yes — accessing the mounting nuts and wire terminals underneath the tub requires pulling the unit forward after removing the two screws that secure it to the counter. Some technicians have managed the nut removal with a deep socket without fully pulling the unit, but planning for full access makes the job considerably easier, especially the first time. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original heating output, mounting configuration, and terminal layout of the element originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

00622058 Dishwasher Genuine OEM Water Valve  Fits Specific Bosch Dishwasher Models Description: This dishwasher Water Inlet Valve is a Genuine OEM part for specific Bosch dishwasher models. This component is responsible for controlling the flow of water into the dishwasher. It operates via electrical signals from the dishwasher's control board, opening to allow water to enter during the fill cycle and closing to prevent water from entering during other cycles. ✅ Key Features: Genuine OEM Part for Bosch #00622058 120V, 60Hz single solenoid valve Includes mounting bracket and hose connection port Durable thermoplastic construction 🔁 Replaces Part Numbers: 00622058, 1999956, 622058, AH3491417, AP4927070, EA3491417, PS3491417, PS8728724. 🔧 Fixes These Common Symptoms: Dishwasher not filling with water Low or slow water flow Water inlet error codes Humming or clicking without water intake Leaking around the valve area 🧰 Compatible With: ✔️ Bosch✔️ Thermador✔️ Gaggenau✔️ Siemens(Check your model number or contact us for assistance.) ✅ Affordable aftermarket solution ✅ Always Fast and Free U.S. shipping ✅ Backed by helpful support and easy returns ✅ Trusted by DIYers and appliance techs 🛒 Restore your dishwasher’s performance — order the 00622058 water inlet valve today from Parts-O-Matic.com, and get it delivered fast and free.

Read more less

XPARTCO HS810 Refrigerator 3-in-1 Hard Start Kit 1/12 to 1/5 HP 120V The XPARTCO XPHS810 is a universal 3-in-1 hard start kit that combines a solid-state starting relay, a start capacitor, and thermal overload protection into a single prewired unit for refrigerator and freezer compressors rated 1/12 to 1/5 HP at 120V (110–125VAC). It's designed as a direct equivalent to the widely used Supco RCO810 and similar kits, giving a struggling compressor extra starting torque to overcome internal friction and gas pressure at startup — commonly used to fix the classic "click-buzz-click" no-start symptom without replacing the entire compressor. The kit is fully prewired with color-coded leads (typically black = Common, white = Start, red = Run) and mounts directly onto the compressor's terminal pins, with instructions printed on the unit itself. It directly replaces Supco RCO810, URCO810, URC0810, RC0810, RC100, TJ90RCO810, AP4503019, ERP810, ERPU810, HS8, HS810, HS81, PCS810, and Mars 32781. Installs in 15–30 minutes with basic hand tools. Quick Answer The XPARTCO HS810 3-in-1 Hard Start Kit fixes refrigerators and freezers whose compressor makes a repeated "click-buzz-click" sound and fails to start, or that shut off on thermal overload during startup. Combines relay, start capacitor, and overload protector in one prewired unit for 1/12 to 1/5 HP compressors, 120V, 3.5A RLA. Replaces Supco RCO810, URCO810, RC0810, RC100, TJ90RCO810, AP4503019, ERP810, HS8, HS810, HS81, PCS810, Mars 32781. Do not install on LG linear/inverter compressors — see Installation Notes. Common Problems This Part Fixes Compressor makes a repeated "click-buzz-click" noise and fails to start Refrigerator or freezer runs warm because the compressor won't stay running Compressor hums but doesn't start, then trips off on overload Refrigerator cycles on and off rapidly without reaching temperature Older or worn compressor that starts hard, especially after a power outage ⚠ Capacitor Hazard — Read Before Servicing This kit contains a start capacitor, which can store a dangerous electrical charge even after the refrigerator is unplugged. Always disconnect power before servicing, and discharge the capacitor safely (using an insulated-handle resistor tool or by briefly shorting the terminals with an insulated screwdriver) before handling it. Never touch capacitor terminals with bare hands. If you are not comfortable working around stored electrical charge, have this repair performed by a qualified technician. Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This 3-in-1 hard start kit directly replaces the following OEM and cross-reference part numbers: XPHS810, RCO810, URCO810, URC0810, RC0810, RC100, TJ90RCO810, AP4503019, ERP810, ERPU810, HS8, HS810, HS81, PCS810, Mars 32781 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This universal hard start kit is compatible with refrigerator and freezer compressors in the following range: Compressors rated 1/12 HP through 1/5 HP 120V (110–125VAC) single-phase compressors Standard PSC (permanent split capacitor) and RSIR compressor types across Whirlpool, GE, Frigidaire, LG, Samsung, and most other major brands Important: Do NOT install this kit on LG linear/inverter compressors, or any compressor using a variable-speed inverter board (often labeled "Inverter," "Linear," "BLDC," or "Digital"). Connecting a standard hard start kit to an inverter-driven compressor can destroy the inverter control board. Check your compressor's label before ordering, or contact our support team with your model number if you're unsure. Key Features 3-in-1 design combines starting relay, start capacitor, and thermal overload protector in one prewired unit Delivers additional starting torque to help a struggling compressor overcome startup friction and gas pressure Resolves "click-buzz-click," "won't start," and "trips on overload" symptoms on eligible compressors Rated for 1/12 to 1/5 HP compressors at 120V, 3.5A RLA Prewired, color-coded leads with instructions printed on the unit for straightforward installation Can operate with or without an existing run capacitor Replaces Supco RCO810, URCO810, RC0810, RC100, TJ90RCO810, AP4503019, ERP810, HS8, HS810, HS81, PCS810, and Mars 32781 Aftermarket replacement built to OEM-equivalent quality and safety standards Product Specifications Part Number XPHS810 Equivalent To Supco RCO810 / RC0810 Part Type 3-in-1 Refrigerator/Freezer Hard Start Kit (Relay, Capacitor, Overload) Condition Aftermarket Replacement HP Range 1/12 to 1/5 HP Voltage 120V (110–125VAC) Current Rating 3.5A RLA Terminal / Wire Color Code Black = Common (C), White = Start (S), Red = Run (R) — typical; confirm against included diagram Not Compatible With LG linear/inverter compressors Installation Notes ⚠️ Unplug Refrigerator Before Starting — Discharge Capacitor Safely Disconnect power before beginning. Before touching any wiring, check your compressor's data label to confirm it is NOT a linear/inverter/BLDC compressor — this kit is not compatible with those and can damage the inverter board if connected. Access the compressor compartment, typically at the rear or bottom of the unit. Remove the existing relay/overload assembly by gently pulling it straight off the compressor terminal pins — do not force or twist. Use a multimeter to confirm which pins are Common (C), Start (S), and Run (R) if not already labeled. Connect the hard start kit's wires to the matching pins. Wire the kit's main power leads into the refrigerator's supply wiring using wire nuts, following the included diagram. Secure the kit with zip ties or its mounting strap to prevent vibration damage during compressor operation. Restore power and confirm the compressor starts smoothly without repeated clicking. Tools needed: nut driver or screwdriver, digital multimeter, wire nuts, insulated screwdriver (for capacitor discharge). Frequently Asked Questions My compressor makes a clicking or buzzing sound and won't start — will this fix it? A hard start kit resolves this in many cases, especially on older or worn compressors that struggle to overcome internal gas pressure at startup. However, "click-buzz-click" can also indicate a failing compressor winding or a compressor nearing end of life. If the hard start kit doesn't resolve the issue, the compressor itself may need replacement — a hard start kit can extend a marginal compressor's life but can't revive one with failed internal windings. Can I use this on any refrigerator? This kit works on standard PSC and RSIR compressors within the 1/12 to 1/5 HP range at 120V. It is NOT compatible with LG linear/inverter compressors or any variable-speed inverter-driven compressor — connecting it to one of those can destroy the inverter control board. Check your compressor's label for "Inverter," "Linear," "BLDC," or "Digital" before ordering. Do I need to remove my existing start capacitor or relay first? Yes — remove the old relay/overload assembly from the compressor terminal pins before installing this kit. The XPHS810 is designed to work with or without an existing separate run capacitor remaining in the circuit, but the old start relay and any old start capacitor should be removed and replaced by this kit, not left in place alongside it. Is this safe to install myself? Many DIYers install hard start kits successfully, but this repair involves a capacitor that can hold a dangerous electrical charge even after the unit is unplugged, plus correctly identifying compressor terminals. If you're not comfortable working around stored electrical charge or don't have a multimeter to confirm terminal identification, we'd recommend having a qualified technician perform this repair. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10195622 Dishwasher Dish Rack Stop Clip Replaces WPW10195622 The XPARTCO W10195622 is an aftermarket replacement upper dishrack stop clip for Whirlpool dishwashers, and also fits select Jenn-Air, Kenmore, KitchenAid, and Amana models. This small plastic clip mounts at the back end of the upper dishrack's slide rail, preventing the rack from sliding in too far and striking the rear wall of the dishwasher cabinet, or from coming off the track entirely when pulled out. Light gray in color, measuring approximately 1-1/4" wide, and sold individually — one clip works for either the left or right side of the upper rack. Over time, the plastic can crack or break from repeated use, allowing the rack to slide too far or come loose from its track. A broken stop clip typically shows up as the upper rack sliding out too far, coming off the rails, or falling when pulled forward. It directly replaces WPW10195622, W10195622, WPW10195622VP, 1872168, AP6016778, AWP49232, EAP11750071, PD00002724, PS11750071. Quick Answer The W10195622 Dishwasher Dish Rack Stop Clip fixes Whirlpool, Jenn-Air, Kenmore, KitchenAid, and Amana dishwashers where the upper rack slides too far, comes off the rails, or falls out when pulled forward. Light gray, approx. 1-1/4" wide, sold individually. Replaces WPW10195622, W10195622, WPW10195622VP, 1872168, AP6016778, AWP49232, EAP11750071, PD00002724, PS11750071. This clip is sold individually — if both the left and right stops need replacing, order two. Common Problems This Part Fixes Upper dishrack slides in too far and hits the rear wall of the cabinet Upper dishrack comes off the slide rail when pulled forward Upper dishrack falls out of the dishwasher Broken or missing stop clip visible at the back of the track Rack rollers coming out of the track Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher dish rack stop clip directly replaces the following OEM and cross-reference part numbers: WPW10195622, W10195622, WPW10195622VP, 1872168, AP6016778, AWP49232, EAP11750071, PD00002724, PS11750071 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This stop clip is compatible with select Whirlpool dishwashers, and also fits select Jenn-Air, Kenmore, KitchenAid, and Amana dishwashers built on the Whirlpool platform, including model numbers such as WDT710PAHZ, WML35011KB, WVU7130JS, KUDC10FXSS5, KUDE40FXBL1, WDT790SAYM1, 7WDT770PAYM0, 7WDT770PAYM1, 7WDT770PAYW0, 7WDT790SAYM0, and WDF730PAYB0. Note: This clip mounts at the back end of the slide rail/drawer track (a related but separate part, WPW10195623). Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement upper dishrack stop clip Resolves "rack slides too far," "comes off the rails," and "rack falls out" symptoms Light gray, approximately 1-1/4" wide Works for either the left or right side of the upper rack Snap-fit installation — no screws required Sold individually Replaces WPW10195622, W10195622, WPW10195622VP, 1872168, AP6016778, AWP49232, EAP11750071, PD00002724, PS11750071 Compatible with Whirlpool, Jenn-Air, Kenmore, KitchenAid, and Amana dishwashers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number W10195622 OEM Part Number WPW10195622 Part Type Dishwasher Upper Dishrack Stop Clip Condition Aftermarket Replacement Color Light Gray Width Approx. 1-1/4" Fits Left or right side (universal for either) Related Part WPW10195623 slide rail/drawer track (sold separately) Repair Difficulty Easy — basic hand tools, novice repair experience Quantity 1 stop clip (sold individually) Compatible Brands Whirlpool, Jenn-Air, Kenmore, KitchenAid, Amana Installation Notes ⚠️ Unplug Dishwasher Before Starting Disconnect power to the dishwasher before beginning. Wear work gloves. Slide out the upper dish rack to locate the existing stop clip at the back end of the slide rail. Using a flathead screwdriver, gently pry out the old, broken stop clip from the track. Snap the new W10195622 clip into the same position at the back of the track, pressing it in firmly until it's securely seated — this is a snap-fit clip rather than a screwed connection. Slide the rack back onto the rails and test it by pulling it forward and pushing it back, confirming it stops properly at both ends without sliding off the track or hitting the rear wall. Tools needed: flathead screwdriver. Frequently Asked Questions My upper rack fell out of the dishwasher. Is this the part I need? Yes, this is a well-documented symptom of a broken stop clip. One customer described exactly this: "Plastic stop on upper dishwasher rack was broken allowing the rack to come out and fall," and resolved it by prying out the old, broken clip and snapping in a new one in just a few minutes. Do I need one clip or two? This part is sold individually, and one clip works for either the left or right side of the upper rack. If both the left and right stop clips need replacing, you'll need to order two. Do I need to screw this in, or does it snap into place? This clip snaps into place rather than being screwed in. A flathead screwdriver is useful for prying out the old, damaged clip, but installing the new one is a simple snap-fit into the track — no screwing required. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the size, color, and snap-fit mounting of the original WPW10195622 stop clip used in compatible Whirlpool, Jenn-Air, Kenmore, KitchenAid, and Amana dishwashers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

8270020CM Dishwasher Door Spring Door balance spring - 7.75" overall length. Fits Whirlpool dishwashers. Replaces Part Numbers:WP8270020, 8270020, AP6012319, PS11745526.   This is an aftermarket part that can be used as a replacement for the OEM part.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WR2X7054CM Dishwasher / Refrigerator Push-on Nut Push on retainer clip. Used on GE dishwashers and refrigerators. Replaces Part Numbers:WR2X7054, WD02X0429, WD2X429, WR02X7054, AH298353, EA298353, AP2059046, PS298353.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

Choice W10898291 Range Spark Module (Board) Direct spark ignition module. Fits specific Maytag, Kenmore, Whirlpool gas range models Replaces Part Numbers: W10898291, W10818365, AP6034131, PS11765825. Description: This Spark Module is a replacement part for specific Maytag, Kenmore, Whirlpool gas range models. Located underneath each sealed burner bowl, it generates the high voltage spark needed for reliable ignition of surface flames. Key Features: ✅ Replaces: W10898291, W10818365, AP6034131, PS11765825. ✅ Fits brands: Whirlpool, Maytag, Kenmore, Amana & more ✅ Ensures lid locks properly during operation ✅ Direct-fit, plug-and-play installation ⚠️ Always disconnect power before installation. Contact us to confirm fit for your washer model. 📦 Part Number: W10898291CM💯 30-Day Money Back Guarantee This is an aftermarket part that can be used as a replacement for the OEM part.  

Read more less

XPARTCO 17438200000160 Gas Dryer Flame Switch The XPARTCO 17438200000160 is an aftermarket replacement gas dryer flame switch compatible with select Midea, Insignia gas dryers, including the MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW/CDG45N1AW series, NSDRE67WH8A, NSFDRG67WH8A, NSDRE67WH8AC, NSTDRG75W1. The flame switch is a safety component mounted on the burner assembly that confirms a flame is actually present after the gas valve opens and the igniter lights the burner. If the switch does not detect a flame within the expected window, it signals the control board to shut off the gas valve, preventing unburned gas from continuing to flow into the dryer cabinet. When the flame switch fails, the dryer may not heat at all, may shut off the burner shortly after ignition (short-cycling the flame), may trip a no-heat fault code on models with digital displays, or — in rarer failure modes — may fail to shut off gas flow appropriately, which is a safety-relevant failure. It directly replaces 17438200000160 (Midea OEM). Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 17438200000160 Gas Dryer Flame Switch fixes Midea gas dryers that won't heat, where the burner lights and then shuts off shortly after ignition, or where a no-heat fault is displayed. Mounted on the burner assembly — confirms flame presence after ignition and signals the control board to keep the gas valve open. Genuine Midea OEM part number. Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers. Common Problems This Part Fixes Gas dryer not heating — flame switch not confirming flame presence to the control board Burner lights briefly and then shuts off — flame switch failing to maintain the "flame confirmed" signal No-heat fault code displayed on models with digital control panels Dryer runs and tumbles normally but produces no heat Burner repeatedly cycling on and off rapidly during a heat cycle Visible damage, corrosion, or carbon buildup on the flame switch near the burner Replaces Part Numbers This flame switch directly replaces the following part number: 17438200000160, AP7153000, PS18188577. This is the Midea, Insignia manufacturer part number used across multiple Midea gas dryer models. Contact our support team with your model number if you need confirmation before ordering. Compatibility This flame switch is compatible with select Midea, Insignia gas dryers, including: Midea MLG45N1BWW gas dryer Midea MLG45N3BMG gas dryer Midea MLG45N3BWW gas dryer Midea MLG52S7AWW gas dryer (8.0 cu. ft. front load) Midea CDG41N1AW gas dryer (Criterion, air vent) Midea CDG45N1AW gas dryer (Criterion, air vent) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Confirms flame presence at the burner after ignition and signals the control board accordingly Safety component — helps ensure the gas valve closes promptly if a flame is not detected Mounts directly to the burner assembly in the same position as the original switch Genuine Midea manufacturer part number — designed as a direct fit for compatible models Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers Installs in 30–45 minutes with basic hand tools Product Specifications Part Number XP17438200000160 Part Type Gas Dryer Flame Switch Condition Aftermarket Replacement Application Gas Dryers (Midea platform) Location Mounted on the burner assembly Compatible Brands Midea Installation Notes ⚠️ Gas Appliance Safety Warning This part is installed in a gas dryer. Always unplug the dryer and shut off the gas supply at the shutoff valve before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. Do not restore power or gas until the repair is fully complete and all connections are confirmed secure. If you are not comfortable working on gas appliances or safety-relevant flame-detection components, have this part installed by a qualified technician. ⚠️ Wear Work Gloves — Access Requires Cabinet Disassembly Disconnect power and shut off gas before beginning. Wear work gloves throughout — there are sharp metal edges inside the dryer cabinet. Remove the lint filter and the screws securing the lint filter housing. Release the top panel locking clips with a putty knife and lift the top panel. Disconnect the door switch harness and remove the front panel to access the drum and burner assembly. Locate the flame switch mounted on the burner assembly — it is positioned to detect the flame produced once the igniter lights the gas. Photograph the wire connections before disconnecting. Disconnect the wires from the old flame switch, remove the mounting screw, and pull the switch free. Install the new 17438200000160 flame switch in the same position, secure the mounting screw, and reconnect the wires. Reassemble the front panel, drum, and top panel in reverse order. Restore gas and power, and run a test heat cycle to confirm the burner ignites and stays lit normally. Tools needed: Phillips screwdriver, putty knife, work gloves. Frequently Asked Questions What does the flame switch do, and how is it different from an igniter? The igniter is the component that heats up and ignites the gas at the burner. The flame switch is a separate safety component that confirms a flame is actually present after the igniter has done its job and the gas valve has opened. If the flame switch does not detect the expected flame condition, it signals the control system to close the gas valve, stopping gas flow. This two-part system — ignition plus flame confirmation — is a standard safety design in gas dryers and gas appliances generally, ensuring gas does not continue flowing if combustion isn't actually occurring. My burner lights and then shuts off after a few seconds — is this the flame switch? Yes, this is a common symptom of a failing flame switch. If the switch is not reliably maintaining its "flame detected" signal to the control board even though the burner is genuinely lit, the system may interpret this as a flame failure and shut the gas valve as a safety precaution — causing the burner to repeatedly light and then extinguish. This short-cycling pattern during what should be a continuous heat cycle is a strong indicator that the flame switch needs replacement. Why is this called a "flame switch" rather than a "flame sensor"? Different manufacturers use different terminology for similar flame-detection safety components. On Whirlpool-family gas dryers, this type of part is typically called a "flame sensor" — a bimetal-style sensor near the igniter that closes a circuit when it senses sufficient heat. Midea's parts catalog labels this specific component the "flame switch," and it serves an analogous safety role within the Midea gas burner system: confirming the presence of a flame after ignition. The terminology differs by manufacturer, but the safety function is similar in concept. Why does this repair require opening the whole dryer cabinet? On Midea gas dryers, the flame switch is mounted directly on the burner assembly inside the dryer cabinet, which is only accessible after removing the lint filter housing, releasing the top panel, and removing the front panel. This is a more involved repair than swapping an externally accessible part, but it follows the same general gas dryer disassembly procedure used for replacing igniters, thermal fuses, and other burner-area components. Since the cabinet must be opened, it can be a good opportunity to inspect other burner components (igniter, gas valve coils) for wear at the same time. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is manufactured to match the dimensions, mounting configuration, and function of the original 17438200000160 Midea flame switch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

422133CM Surface Element Infinite Switch 120V, 15 Amp ceramic element. Fits Bosch glasstop free standing ranges Replaces Part Numbers:00422133, 422133, AH3462872, EA3462872, AP3723298, PS3462872, PS8713176.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less