Search results for "refrigerator control board"

XPARTCO XPDC35X5-450R Dual Run Capacitor (35/5 MFD, 450V, Round) The XPARTCO XPDC35X5-450R is a universal dual run capacitor for central air conditioners, heat pumps, and condensing units. A run capacitor works alongside a single-phase AC motor to keep it running efficiently once it's started, boosting torque and correcting the phase of the current feeding the motor's windings. This is a dual capacitor, meaning it combines two separate capacitors — one for the compressor, one for the condenser fan motor — into a single three-terminal can, which is why nearly every residential outdoor AC unit uses exactly this style of component to run both motors from one part. Rated 35 MFD for the compressor circuit and 5 MFD for the fan motor circuit, at 450VAC, in a round aluminum can housing. Because a capacitor's voltage rating is a ceiling rather than a fixed match, this 450V-rated capacitor can safely replace an original capacitor rated 370V or 440V — going higher on voltage is always safe, going lower is not. Over time, the dielectric material inside a run capacitor breaks down from heat cycling and electrical stress, causing it to lose capacitance or fail outright. A failing dual capacitor produces a very recognizable set of symptoms: the outdoor unit hums but the compressor or fan won't start, the fan spins slowly or needs a manual push to get going, the system trips the breaker, or the capacitor can itself is visibly bulging, domed, or leaking oily residue at the top. Quick Answer The XPARTCO XPDC35X5-450R Dual Run Capacitor fixes central air conditioners and heat pumps where the outdoor unit hums but won't start, the compressor or fan motor won't run, the fan spins slowly or needs a manual push, the breaker trips, or the capacitor can is visibly bulged or leaking. 35 MFD (compressor) + 5 MFD (fan) dual capacitor, 450VAC, round, 3-terminal. Universal fit for equipment originally speced at 370V or 440V, since a higher voltage rating is always a safe upgrade. Capacitors store a dangerous electrical charge even after power is disconnected — always discharge before handling. Common Problems This Part Fixes Outdoor AC unit hums but the compressor won't start Condenser fan won't spin, or spins slowly and needs a manual push to get going System trips the breaker shortly after starting AC blows warm air because the compressor isn't running Repeated clicking sound from the contactor as it tries and fails to start the motor Capacitor can visibly bulging, domed on top, or leaking oily residue System that used to start slowly and has now stopped starting altogether Burning smell from the outdoor unit's electrical compartment Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers XPDC35X5-450R This is a universal component rather than a single-manufacturer part, so the specific OEM number your HVAC system's label references will vary by brand (Goodman, Trane, Carrier, Rheem, York, Lennox, Amana, and others). This capacitor is a correct replacement for any dual run capacitor matching the 35 MFD / 5 MFD rating with a voltage rating of 450V or lower. If you have your original part number, contact our support team and we will verify compatibility before you order. Compatibility This dual run capacitor is a universal replacement compatible with central air conditioners, heat pumps, and condensing units across all major HVAC brands, wherever the original capacitor is rated: 35 MFD (compressor) + 5 MFD (fan motor) 370V, 440V, or 450V (this capacitor's 450V rating exceeds and safely replaces either lower rating) Round can shape with 3 terminals Note: The MFD (microfarad) rating must match your original capacitor exactly on both sides — do not substitute a different MFD value for either the compressor or fan side. Voltage rating, on the other hand, can be equal to or higher than the original (450V safely replaces 370V or 440V), but never lower. Can shape (round vs. oval) affects only physical fit inside your unit's electrical compartment, not performance. If you're unsure of your original capacitor's specifications, they're printed directly on its can — contact our support team if you'd like help confirming compatibility. Key Features Universal dual run capacitor — supports both the compressor and condenser fan motor from one component 35 MFD compressor rating + 5 MFD fan motor rating in a single 3-terminal can 450VAC rating — a safe upgrade replacement for equipment originally speced at 370V or 440V Round aluminum can construction Resolves "hums but won't start," "fan spins slowly," "trips the breaker," and "bulging or leaking can" symptoms caused by capacitor failure 1/4" quick-connect terminals for a direct plug-on fit to standard HVAC wiring 50/60Hz rated Safety approved: CQC, VDE, TÜV, and CL; built to GB/T 3667 and EN 60252 standards Built to meet or exceed industry-standard specifications for this capacitor class Product Specifications Part Number XPDC35X5-450R Part Type Dual Run Capacitor Condition New — Universal Replacement Part Capacitance — Compressor 35 MFD (µF) Capacitance — Fan Motor 5 MFD (µF) Voltage Rating 450VAC Shape Round Terminals 3 (1/4" quick-connect) Frequency 50/60 Hz Tolerance ±5% Construction Type Polypropylene film capacitor Operating Temperature Range -40°C to 70°C (-40°F to +158°F) Safety Approvals CQC, VDE, TÜV, CL Approval Standard GB/T 3667, EN 60252 Application Central Air Conditioners, Heat Pumps, Condensing Units Quantity 1 dual run capacitor Compatible Brands Universal — all major HVAC brands Installation Notes ⚠️ Danger — Capacitors Store A Dangerous Electrical Charge Shut off power to the outdoor unit at the disconnect box and at the breaker before beginning. A capacitor stores an electrical charge even after power has been disconnected, and that charge can deliver a serious or fatal shock. Before touching any terminal, discharge the capacitor by shorting each pair of terminals together (C-to-Fan, C-to-Herm, and Fan-to-Herm) using an insulated-handle screwdriver, or by using a proper capacitor discharge tool with a resistor. Never short the terminals with a bare metal tool held with your bare hand. If you are not fully comfortable performing a capacitor discharge safely, have a qualified HVAC technician replace this part instead. ⚠️ Photograph The Wiring Before Disconnecting — Match Terminals Exactly Wear work gloves and safety glasses. After confirming the capacitor is fully discharged, photograph the wiring on the old capacitor's terminals before disconnecting anything — dual capacitors are labeled C (Common), Herm or Comp (compressor/hermetic), and Fan, and getting a wire on the wrong terminal can damage the new capacitor or the motor it feeds. Note which terminal each wire came from, or label them individually with tape. Remove the mounting strap or bracket holding the old capacitor in its housing, and disconnect each wire from its terminal. Install the new XPDC35X5-450R in the same mounting position, secure it with the strap or bracket, and reconnect each wire to the matching terminal (C, Herm, and Fan) exactly as labeled. Double-check every connection before restoring power. Restore power at the breaker and disconnect box, and confirm the compressor and fan both start promptly and run smoothly. Tools needed: insulated-handle screwdriver or capacitor discharge tool, nut driver, work gloves, safety glasses. Frequently Asked Questions My AC unit hums but won't start. Is this the capacitor? It's one of the most common causes of exactly that symptom. A run capacitor gives the compressor or fan motor the extra push needed to start turning; without it, the motor can draw power and hum in place without ever actually starting to spin. If you can see the capacitor can and it looks bulged, domed on top, or is leaking a brown oily residue, that's strong visual confirmation of failure. Can I use a 450V capacitor to replace my old 370V or 440V one? Yes. Voltage rating is a ceiling, not an exact match requirement — a capacitor rated for a higher voltage than your original will work safely and often lasts longer under the same electrical stress. What you cannot do is go the other direction: never install a capacitor with a lower voltage rating than your original, since that risks premature failure or the capacitor breaking down under normal operating conditions. Does the round vs. oval shape matter? Only for physical fit inside your unit's electrical compartment — it has no effect on electrical performance. If your unit's mounting bracket or available space is sized for a round can, use a round capacitor; if it's sized for an oval can, use an oval one. The MFD and voltage ratings are what matter electrically, not the shape. The fan spins if I give it a push, but won't start on its own. What does that mean? This is a classic sign of a weak or failing capacitor — it may still have enough charge to keep the motor running once it's already spinning, but not enough to provide the initial starting torque. This is a strong signal to replace the capacitor before it fails completely and leaves you with no cooling at all. Is this a genuine OEM part? This is a universal replacement part rather than a brand-specific OEM part. Because dual run capacitors are a standardized component defined by their electrical specifications rather than their manufacturer, this capacitor is a correct replacement for any unit's original capacitor that shares the same 35/5 MFD, 450VAC, round dual run capacitor rating — regardless of which HVAC brand originally installed it. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Replacement Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

EXPFFSB Microwave Door Switch and Fuse Kit – Replaces FSSBA016KIT & 5303319559 – Compatible with Frigidaire & Electrolux Microwaves Product Description Restore proper microwave safety operation with the EXPFFSB Microwave Door Switch and Fuse Kit. This aftermarket repair kit includes the essential components needed to fix common microwave door and power issues, including one door switch and one ceramic fuse. A faulty door switch or blown fuse can prevent the microwave from starting, cause intermittent power loss, or trigger safety shutdowns. Replacing both components together helps restore reliable microwave operation and prevents repeat failures. This kit is engineered to match original fit and electrical performance while offering a cost-effective alternative to OEM parts. This kit includes: 1 Microwave Door Switch 1 Microwave Fuse Replaces Part Numbers FSSBA016KIT, FFS-BA016/KIT, PS2422854, FFSBA016/KIT-R, FFSBA016/KIT, FFSBA016KIT, 5303319559, 634759, 75303319559, PD00026535, EAP466978, AH466978, EA466978, AP2148482, PS466978, 5304467695, 1467286, 75304467695, AH2339493, EA2339493, AP4357598, PS2339493, 5304461109, 1260958, 75304461109, AH1765534, EA1765534, AP4057424, PS1765534, 4313105, 565130, 8185302, AH358056, EA358056, AP3032745, PS358056, 5304479020, 1793730, AH3409702, EA3409702, AP4588054, PS3409702 Compatibility This microwave door switch and fuse repair kit fits select Frigidaire, Electrolux, Gibson, Kelvinator, and Kenmore (Frigidaire-manufactured) microwaves. Common compatible models include (but are not limited to): Frigidaire FFMV1645TS Frigidaire FGMV176NTF Always verify your microwave’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Complete Repair Kit – Includes door switch and microwave fuse ⚡ Restores Microwave Power – Fixes no-start and power loss issues 🔒 Door Safety Function – Ensures proper door interlock operation 🧩 Direct-Fit Components – Designed for straightforward installation 💰 Cost-Effective Repair – Replace two common failure parts at once 📐 Product Specification Kit Number: EXPFFSB Includes: (1) Microwave Door Switch (1) Microwave Fuse Application: Microwave door interlock and circuit protection Fuse Type: Ceramic microwave line fuse Quality Level: Aftermarket replacement kit (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver ⚠️ Safety First: Unplug the microwave before servicing to avoid electrical shock. Microwaves contain high-voltage components—ensure the capacitor is discharged before handling internal parts. Basic Steps: Disconnect microwave power. Remove the outer cabinet or control panel to access the door switch assembly. Replace the faulty door switch. Locate and replace the blown fuse. Reassemble the microwave and restore power. Test door operation and heating function. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Replacement Parts 🔄 30-Day Return Policy Restore microwave safety and reliable operation — Add to Cart Now for a complete repair solution!

Read more less

MWCDF-095-2Kit Microwave Capacitor, Diode & Fuse Kit – Universal High-Voltage Repair Kit Product Description Restore proper microwave heating and electrical safety with the MWCDF-095-Kit Microwave Capacitor, Diode & Fuse Kit. This high-quality aftermarket repair kit includes the three most common high-voltage components required to fix no-heat and power-related microwave issues: a high-voltage capacitor, high-voltage diode, and high-voltage fuse. Failed components in the HV circuit can cause the microwave to run without heating, blow fuses, or shut down completely. Replacing the full kit helps ensure reliable heating and safe operation. This Kit Includes Following Parts: 1 Capacitor 2 universal Diode (EXPHV10)  2 Ceramic Fuse (20 amp) 6.35 x 32 mm 2 5Kv Fuse (0.9A) 6x40mm Replaces Part Numbers Capacitor Replaces Part Numbers: TJ13QBP21095, 13QBP0300, 13QBP21095, AP5633423, RC-QZA234WRE0, RC-QZB011MRE0, RCQZA331WRZZ, 5304513458, PD00065299, EAP12365444, 4584979, AP6301645, PS12365444, 00631397, 631397, PD00044249, EAP10057840, 4161979, AP5950362, PS10057840, WB27X11031, PD00040188, EAP2339855, 1474116, AP4362390, PS2339855, WB27X10073, PD00045875, EAP239187, 769853, AP2025984, PS239187, WB27X11011, PD00087136, EAP2345628, 1474103, AP4368101, PS2345628, 2501-001016, 2028385, AP4033712, PS4130923, 8206562, PD00074258, EAP1486840, 1200936, AP3890709, PS1486840, 5304528930, 5304464253, AP7017693, PS2203382, WB27X10009, 254534, AH239117, EA239117, AP2025928, PS239117, WP815073, AP6011690, PS11744888, 2501-000260, AP4033659, PS4130923 and more Compatibility This universal microwave high-voltage repair kit is compatible with many GE, Whirlpool, Samsung, LG, Frigidaire, Panasonic, Sharp, and Kenmore microwave ovens that use a 0.95 µF high-voltage capacitor, standard microwave HV diode, and HV fuse. Commonly used in countertop, over-the-range, and built-in microwave models. Always verify capacitor rating and fuse specifications before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement Kit – Built to OEM-equivalent electrical specifications ⚡ Complete HV Circuit Repair – Includes capacitor, diode, and fuse 🔥 Fixes No-Heat Issues – Restores proper magnetron power delivery 🛡️ Improves Electrical Safety – Protects microwave from overload and failure 💰 Cost-Effective Solution – Avoids expensive magnetron replacement 📐 Product Specification Kit Name: MWC-095-Kit Component Type: Microwave High-Voltage Repair Kit Capacitor Rating: 2100 VAC, 0.95 µF Diode Type: Microwave high-voltage diode Fuse Type: Microwave high-voltage fuse Application: Magnetron high-voltage power circuit Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, insulated pliers ⚠️ Safety First:Microwaves contain EXTREMELY HIGH VOLTAGE, even when unplugged. Always discharge the high-voltage capacitor before servicing. Professional installation is strongly recommended. Basic Steps: Unplug the microwave and remove the outer cabinet. Safely discharge the existing high-voltage capacitor. Remove the old capacitor, diode, and fuse. Install the new components from the MWCDF-095-Kit. Reassemble the cabinet and restore power. Test microwave heating operation. ⏱️ Time Required: 25–35 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore microwave heating safely and efficiently — Add to Cart Now for a complete, budget-friendly repair solution!

Read more less

WB27X11213CM Microwave Fan Thermostat Closes at 158°F, Opens at 104°F. Fits GE Microwaves. Replaces Part Numbers:WB27X11213, WB24X28950, WB27X10846, SE-7350-004,  AP5791057, PS8754628.  This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

Packard 12007 370V Oval Run Capacitor 7.5 MFD - Compatible with GE, Carrier, Goodman Product Description Keep your HVAC system running smoothly with the Packard 12007 370V Oval Run Capacitor 7.5 MFD. This high-quality non-OEM capacitor is designed for select GE, Carrier, Goodman, and other compatible air conditioners, HVAC systems, and compressors, providing reliable capacitance for motor starting and running. Made with durable aluminum and metallized polypropylene film, it ensures efficient performance, addressing issues like motor failure, overheating, or system shutdowns. Note: Includes one single capacitance oval run capacitor. Disconnect power before installation. Verify voltage and MFD rating compatibility. Replaces part numbers: 12007, 325P755H37A14N4X, 37075H, CR7.5X370, POC7.5A, TOC7.5, SE7537-0, Z50S3707N91, 12907, 14007 Compatibility: Compatible with models including but not limited to: GE, Carrier, Goodman, Rheem, Trane, Lennox: (select air conditioners, HVAC systems, and compressors; verify model compatibility) Universal replacement for 7.5 MFD, 370V capacitors in HVAC applications Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select GE, Carrier, Goodman, Rheem, Trane, Lennox, and other HVAC systems and compressors. 🔐 Specifications: 7.5 MFD, 370V, 50/60 Hz, oval shape, aluminum case with 4 terminals. 💪 Reliable Performance: Durable construction with metallized polypropylene film ensures long-lasting operation (60,000 hours). 🛠️ Easy Installation: Requires screwdriver; typically installed in 10–15 minutes. 🛡️ Effective Fixes: Resolves motor starting issues, system shutdowns, overheating, or humming noises. Product Specification Part Number: Packard 12007 Component Type: Single capacitance run capacitor Material: Aluminum case, metallized polypropylene film Capacitance: 7.5 MFD Voltage: 370V Frequency: 50/60 Hz Terminals: 4, 1/4" male quick-connect Temperature Range: -40°C to 70°C Operational Life: 60,000 hours Mounting: Screw or clip-mounted Operating Conditions: Suitable for HVAC and compressor environments Compliance: UL, CUL, EIA-456-A, Prop 65 warning for California Installation Notes: Safety First: Disconnect the HVAC system or compressor from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your HVAC system efficient today! Add to cart now for a reliable fix!

Read more less

XPARTCO 8318314 Dryer Thermal Cutoff Fuse (352°F) The XPARTCO 8318314 is an aftermarket replacement 352°F thermal cutoff fuse compatible with a wide range of Whirlpool, Maytag, KitchenAid, Kenmore, Amana, Crosley, Roper, Inglis, and Estate dryers. The thermal cutoff fuse is a critical safety device mounted near the heating element housing — it acts as a backup safety in case the high-limit thermostat fails to open. When the air temperature inside the heating element area reaches 352°F, the fuse permanently opens and cuts power to the heater circuit, preventing the dryer from continuing to overheat and creating a fire risk. This is a one-time fuse — once it has tripped, it cannot be reset and must be replaced. White and gray metal/ceramic construction. Dimensions: 1-1/4"L x 1-1/4"W x 2-3/16"H, with approximately 1-5/8" between mounting holes (center to center). It directly replaces 8318314. Important: when the thermal cutoff blows, the high-limit thermostat (8557403 — sold separately) is often also stressed and should be tested or replaced at the same time. Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO 8318314 Dryer Thermal Cutoff Fuse (352°F) fixes Whirlpool, Maytag, KitchenAid, Kenmore, Amana, Crosley, Roper, Inglis, and Estate dryers that suddenly stopped heating after an overheat event. One-time fuse — 352°F open, must be replaced once blown. 1-1/4"L x 1-1/4"W x 2-3/16"H, ~1-5/8" between mounting holes. Metal/ceramic. Often replaced alongside the high-limit thermostat (8557403, sold separately). Common Problems This Part Fixes Dryer suddenly stopped heating with no warning — thermal cutoff has blown after an overheat event Dryer runs and tumbles normally but produces no heat No-heat fault following a partially blocked exhaust vent or restricted airflow event Multimeter continuity test shows the cutoff has an open circuit (no continuity) Visible damage or discoloration around the thermal cutoff housing from a prior overheat event Repeated no-heat problems where the thermal cutoff has tripped more than once Replaces Part Numbers This thermal cutoff fuse directly replaces the following OEM and cross-reference part numbers: 8318314 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This 352°F thermal cutoff fuse is compatible with select dryers from the following brands: Whirlpool dryers (Elite, Cabrio, Duet, and WED series — select models including WED9200, WED7300, WED7400, WED7600 and related) Maytag dryers (Maxima and MED series — select models including MED3500, MED6000XW, MEDE900VW and related) KitchenAid dryers (select models) Kenmore / Sears dryers — Elite 110-series and related Whirlpool-built models Amana dryers — NED and YNED series (select models including NED7500VW1 and related) Crosley dryers (CED series and related models) Roper dryers (select models) Inglis dryers (select models) Estate dryers (select models) Important — Check Vent Before Restarting: A blown thermal cutoff is almost always the result of restricted dryer airflow. Before replacing this fuse and restoring service, thoroughly clean the dryer's exhaust vent line all the way to the exterior wall outlet, the lint screen, and any internal lint buildup. Installing a new thermal cutoff without fixing the underlying airflow problem will cause the new fuse to blow within a short time, repeating the failure. Key Features 352°F one-time safety fuse — permanently opens to cut power to the heater circuit if the dryer overheats Backup safety device — protects against overheating in case the high-limit thermostat fails to open Cannot be reset — must be replaced once blown Dimensions: 1-1/4"L x 1-1/4"W x 2-3/16"H; approximately 1-5/8" between mounting holes (center to center) Metal and ceramic construction in white/gray Often replaced together with the high-limit thermostat (8557403, sold separately) as a paired safety repair Compatible with Whirlpool, Maytag, KitchenAid, Kenmore, Amana, Crosley, Roper, Inglis, and Estate dryers Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number 8318314 Part Type Dryer Thermal Cutoff Fuse (Safety Fuse) Condition Aftermarket Replacement Application Electric and Gas Dryers (Whirlpool platform) Trip Temperature 352°F Fuse Type One-Time (must be replaced once blown — cannot be reset) Dimensions 1-1/4"L x 1-1/4"W x 2-3/16"H Mounting Hole Spacing Approx. 1-5/8" center to center Color White / Gray Material Metal / Ceramic Often Replaced With High-Limit Thermostat (8557403, sold separately) Compatible Brands Whirlpool, Maytag, KitchenAid, Kenmore, Amana, Crosley, Roper, Inglis, Estate Installation Notes ⚠️ Unplug Dryer Before Starting — Clean Vent System First Disconnect power before beginning. Wear work gloves to protect your hands. Before installing the new thermal cutoff, thoroughly clean the dryer's vent line — from the lint screen through the duct to the exterior wall outlet, plus any internal lint buildup around the heater housing. A blown thermal cutoff is virtually always caused by restricted airflow; if you don't fix the underlying cause, the new fuse will trip again soon. Access the thermal cutoff by removing the rear (or front, depending on model) access panel of the dryer to expose the heating element housing. The 8318314 thermal cutoff is mounted on or near the heater housing. Photograph the wire connections before disconnecting. Disconnect the wires from the old cutoff and remove the mounting screw(s). Install the new 8318314 cutoff in the same position and reconnect the wires. While the panel is open, this is also the ideal time to test or replace the high-limit thermostat (8557403) — overheat events that blow this fuse often damage that component too. Reassemble the panel, restore power, and run a test heat cycle to confirm normal heat operation. Tools needed: Phillips screwdriver, 1/4" nut driver, multimeter, work gloves. Frequently Asked Questions What's the difference between a thermal cutoff, a thermal fuse, and a high-limit thermostat? All three are safety components in a dryer's heating circuit but they serve different roles. The high-limit thermostat (such as 8557403 or 3391914) is a resettable safety switch — it opens when the air gets too hot, then closes again automatically once it cools. The thermal cutoff (8318314, 352°F) is a one-time fuse on the heating element circuit — it blows permanently if the temperature exceeds 352°F, meaning the high-limit thermostat failed to do its job. The thermal fuse (often 3392519) is a separate one-time fuse mounted on the exhaust duct — it blows if exhaust airflow temperature exceeds its rating. Each protects against a different failure mode and is replaced individually when it blows. Why did my thermal cutoff blow in the first place? A blown thermal cutoff is almost always the result of restricted airflow through the dryer. The most common causes are: a clogged or kinked exhaust vent line, a clogged lint screen, lint buildup inside the dryer cabinet near the heater housing, or a failed blower wheel/motor that's not moving enough air. Less commonly, a failed high-limit thermostat (stuck closed) can let the dryer overheat until the thermal cutoff blows as a last-resort safety. Before replacing this part, identify and fix the underlying airflow issue — otherwise the new fuse will blow within a short time. Should I replace the high-limit thermostat at the same time? Yes, it's highly recommended. The thermal cutoff is the second line of defense against overheating — for it to trip, the high-limit thermostat ahead of it likely failed to open at its normal cycling temperature, was stressed by the overheat event, or was already weakened. Replacing the high-limit thermostat (8557403 on many compatible Whirlpool-platform dryers) at the same time is standard practice and ensures both safety components work correctly together. The 279973 kit even bundles a thermal cutoff with a high-limit thermostat for this reason. Can the thermal cutoff be reset like a circuit breaker? No — the 8318314 is a one-time thermal fuse. Once it opens at 352°F, it permanently breaks the electrical circuit and cannot be reset. Some appliance components (like a high-limit thermostat) can reset automatically as they cool, but a thermal cutoff fuse is a single-use safety device by design. If your dryer suddenly stopped heating and a continuity test on this fuse shows an open circuit, it must be replaced. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from metal and ceramic with the same 352°F trip temperature, dimensions (1-1/4"L x 1-1/4"W x 2-3/16"H), and mounting hole spacing (1-5/8" center to center) as the original 8318314 thermal cutoff fuse. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

LCD30+5X440 HVAC OVAL DUAL RUN CAPACITOR Engineered by an ISO manufacturer with over twenty years' experience in OEM capacitor fabrication, Linebacker® capacitors are manufactured by the OEM factory and are 100% in-line production tested to the same rigorous standards. Features/Benefits 10,000 AFC pressure sensitive short circuit interrupting capability 3-year warranty from the date of purchase Continuous life tested, oil leak tested and dielectric tested for insulation effectiveness Life tested to 85° C operating temperature for 10,000 cycles Manufactured with thick polypropylene foil to handle increased operating temperatures Meets EIA-456A accelerated life test at 70° C for 60,000 hours PCB-free oil to prevent over-heating UL File # E352486 US and Canada UL approved (C22.2NO.190) Specification: Voltage: Up to 440 VAC Operating Temperature: -40°F to 185°F (-40°C to 85°C) Foil Thickness: 6.0 µm +/- 5% Standard Tolerance: +/- 5% MFD Value: 30+5 Style: Oval Size: 2.8x1.77x3.54

Read more less

Genuine OEM W10779716 Oven Bake Element The Genuine OEM Whirlpool W10779716 is the bake element for select Whirlpool-built electric ranges, including Kenmore, KitchenAid, Maytag, Jenn-Air and other brands. The bake element sits at the bottom of the oven and supplies the heat for baking. When it burns out or breaks, the oven may heat unevenly, heat very little, or not heat at all. This is the original Whirlpool part, not an aftermarket equivalent. Similar-looking elements can differ in size and shape, so check your model number before ordering. Quick Answer The Genuine OEM W10779716 Bake Element replaces the lower bake element on a compatible Whirlpool-built electric range when it has burned out or broken. Replaces W10289097 and W10774342. Classic symptoms: little or no heat when baking, or uneven oven heating. Other parts can cause the same symptoms, so confirm the element is the problem. Common Problems This Part Fixes Oven not heating when baking Little heat, or slow preheating Uneven oven heating Broken or burnt bake element Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This bake element replaces or supersedes the following part numbers: W10779716, W10289097, 4161369, W10774342, AP5970727, AWP41874, EAP11703285, OEM17912190, PD00008690, PS11703285 If your old element shows a different number, contact our support team and we'll check whether it matches. Compatibility This bake element is listed for Whirlpool, KitchenAid, Maytag, Jenn-Air, Kenmore and other Whirlpool-built electric ranges, including these examples: Whirlpool YWEE750H0HW5, YWEE745H0FS0, YWFE745H0FE0, YWFE775H0HV4 KitchenAid KSEG950ESS6, YKSEB900EWH7, KSIS730PSS0 Kenmore 664C95123611, 66442793711 Note: The models above are a small sample. Retailers list the part for many more, but it fits only some models of each brand. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool part, not an aftermarket equivalent Lower oven bake element that supplies heat for baking Replaces the earlier Whirlpool numbers W10289097 and W10774342 Product Specifications Part Number W10779716 OEM Part Number W10779716 Part Type Oven Bake Element Condition Genuine OEM Manufacturer Whirlpool Location Bottom of Oven Application Select Whirlpool-Built Electric Ranges Installation Notes ⚠️ Disconnect Power And Let The Oven Cool Before Installing Unplug the range or switch off its circuit breaker, and make sure the oven is cool. Wear work gloves. Pull the range out far enough to reach the back panel if needed. Remove the oven racks and any bottom cover, disconnect the element's wire leads, and remove the mounting screws or bracket. Fit the new element, reconnect the leads securely, and refit the cover. Restore power and test the oven. Frequently Asked Questions My oven isn't heating when baking. Is this the part I need? A burned-out bake element is a common cause. Look for visible breaks, blisters or burn marks on the element. Other parts, such as the control board or temperature sensor, can cause the same symptoms, so confirm the element is the problem before replacing it. Is this an OEM or aftermarket part? This is a genuine OEM part from Whirlpool, not an aftermarket equivalent. Is this the bake element or the broil element? This is the bake element, located at the bottom of the oven. The broil element is a separate part at the top of the oven. Will this fit my range? It fits only some models of each brand, and the model list above is only a sample. Similar-looking elements can differ in size and shape, so check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 17438200000160 Gas Dryer Flame Switch The XPARTCO 17438200000160 is an aftermarket replacement gas dryer flame switch compatible with select Midea, Insignia gas dryers, including the MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW/CDG45N1AW series, NSDRE67WH8A, NSFDRG67WH8A, NSDRE67WH8AC, NSTDRG75W1. The flame switch is a safety component mounted on the burner assembly that confirms a flame is actually present after the gas valve opens and the igniter lights the burner. If the switch does not detect a flame within the expected window, it signals the control board to shut off the gas valve, preventing unburned gas from continuing to flow into the dryer cabinet. When the flame switch fails, the dryer may not heat at all, may shut off the burner shortly after ignition (short-cycling the flame), may trip a no-heat fault code on models with digital displays, or — in rarer failure modes — may fail to shut off gas flow appropriately, which is a safety-relevant failure. It directly replaces 17438200000160 (Midea OEM). Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 17438200000160 Gas Dryer Flame Switch fixes Midea gas dryers that won't heat, where the burner lights and then shuts off shortly after ignition, or where a no-heat fault is displayed. Mounted on the burner assembly — confirms flame presence after ignition and signals the control board to keep the gas valve open. Genuine Midea OEM part number. Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers. Common Problems This Part Fixes Gas dryer not heating — flame switch not confirming flame presence to the control board Burner lights briefly and then shuts off — flame switch failing to maintain the "flame confirmed" signal No-heat fault code displayed on models with digital control panels Dryer runs and tumbles normally but produces no heat Burner repeatedly cycling on and off rapidly during a heat cycle Visible damage, corrosion, or carbon buildup on the flame switch near the burner Replaces Part Numbers This flame switch directly replaces the following part number: 17438200000160, AP7153000, PS18188577. This is the Midea, Insignia manufacturer part number used across multiple Midea gas dryer models. Contact our support team with your model number if you need confirmation before ordering. Compatibility This flame switch is compatible with select Midea, Insignia gas dryers, including: Midea MLG45N1BWW gas dryer Midea MLG45N3BMG gas dryer Midea MLG45N3BWW gas dryer Midea MLG52S7AWW gas dryer (8.0 cu. ft. front load) Midea CDG41N1AW gas dryer (Criterion, air vent) Midea CDG45N1AW gas dryer (Criterion, air vent) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Confirms flame presence at the burner after ignition and signals the control board accordingly Safety component — helps ensure the gas valve closes promptly if a flame is not detected Mounts directly to the burner assembly in the same position as the original switch Genuine Midea manufacturer part number — designed as a direct fit for compatible models Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers Installs in 30–45 minutes with basic hand tools Product Specifications Part Number XP17438200000160 Part Type Gas Dryer Flame Switch Condition Aftermarket Replacement Application Gas Dryers (Midea platform) Location Mounted on the burner assembly Compatible Brands Midea Installation Notes ⚠️ Gas Appliance Safety Warning This part is installed in a gas dryer. Always unplug the dryer and shut off the gas supply at the shutoff valve before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. Do not restore power or gas until the repair is fully complete and all connections are confirmed secure. If you are not comfortable working on gas appliances or safety-relevant flame-detection components, have this part installed by a qualified technician. ⚠️ Wear Work Gloves — Access Requires Cabinet Disassembly Disconnect power and shut off gas before beginning. Wear work gloves throughout — there are sharp metal edges inside the dryer cabinet. Remove the lint filter and the screws securing the lint filter housing. Release the top panel locking clips with a putty knife and lift the top panel. Disconnect the door switch harness and remove the front panel to access the drum and burner assembly. Locate the flame switch mounted on the burner assembly — it is positioned to detect the flame produced once the igniter lights the gas. Photograph the wire connections before disconnecting. Disconnect the wires from the old flame switch, remove the mounting screw, and pull the switch free. Install the new 17438200000160 flame switch in the same position, secure the mounting screw, and reconnect the wires. Reassemble the front panel, drum, and top panel in reverse order. Restore gas and power, and run a test heat cycle to confirm the burner ignites and stays lit normally. Tools needed: Phillips screwdriver, putty knife, work gloves. Frequently Asked Questions What does the flame switch do, and how is it different from an igniter? The igniter is the component that heats up and ignites the gas at the burner. The flame switch is a separate safety component that confirms a flame is actually present after the igniter has done its job and the gas valve has opened. If the flame switch does not detect the expected flame condition, it signals the control system to close the gas valve, stopping gas flow. This two-part system — ignition plus flame confirmation — is a standard safety design in gas dryers and gas appliances generally, ensuring gas does not continue flowing if combustion isn't actually occurring. My burner lights and then shuts off after a few seconds — is this the flame switch? Yes, this is a common symptom of a failing flame switch. If the switch is not reliably maintaining its "flame detected" signal to the control board even though the burner is genuinely lit, the system may interpret this as a flame failure and shut the gas valve as a safety precaution — causing the burner to repeatedly light and then extinguish. This short-cycling pattern during what should be a continuous heat cycle is a strong indicator that the flame switch needs replacement. Why is this called a "flame switch" rather than a "flame sensor"? Different manufacturers use different terminology for similar flame-detection safety components. On Whirlpool-family gas dryers, this type of part is typically called a "flame sensor" — a bimetal-style sensor near the igniter that closes a circuit when it senses sufficient heat. Midea's parts catalog labels this specific component the "flame switch," and it serves an analogous safety role within the Midea gas burner system: confirming the presence of a flame after ignition. The terminology differs by manufacturer, but the safety function is similar in concept. Why does this repair require opening the whole dryer cabinet? On Midea gas dryers, the flame switch is mounted directly on the burner assembly inside the dryer cabinet, which is only accessible after removing the lint filter housing, releasing the top panel, and removing the front panel. This is a more involved repair than swapping an externally accessible part, but it follows the same general gas dryer disassembly procedure used for replacing igniters, thermal fuses, and other burner-area components. Since the cabinet must be opened, it can be a good opportunity to inspect other burner components (igniter, gas valve coils) for wear at the same time. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is manufactured to match the dimensions, mounting configuration, and function of the original 17438200000160 Midea flame switch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DG64-00472B Gas Range / Stove Burner Knob Fits Specific Samsung Range / Cooktop models. Replaces Part Numbers: DG64-00472B, DG64-00347B, 3555006, AP5949297, PS9865173.  Description: The Knob Assembly is a replacement Part designed for adjusting the temperature of specific Samsung surface burner models. It accepts a D-shaped shaft and is sold individually.    This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

ERP 3406108 Dryer Door Switch  Replaces Part Numbers: WP3406108, 3406108, PS11741702, AP6008562  Description: This Door Switch is a replacement part for select Whirlpool dryer models. It is responsible for detecting whether the dryer door is open or closed. When the door is closed, the switch allows the dryer to operate. Conversely, if the door is open, the switch interrupts the electrical circuit to prevent the dryer from running, ensuring safety during use. Fits Models:   LTE5243DQ1 , LTE5243DQ2 , LTE5243DQ3 , LTE5243DQ4 , LTE5243DQ5 , LTE5243DQ6 , LTE5243DQ7 , LTE5243DQ8 , LTE5243DQ9 , LTE5243DQA , LTE5243DQB , LTE5243DT2 , LTE5243DT3 , LTE5243DT4 , LTE5243DT5 , LTE5243DT6 , LTE5243DT7 , LTE5243DZ1 , LTE5243DZ2 , LTG5243DQ1 , LTG5243DQ2 , LTG5243DQ3 , LTG5243DQ4 , LTG5243DQ5 , LTG5243DQ6 , LTG5243DQ7 , LTG5243DQ8 , LTG5243DQ9 , LTG5243DQA , LTG5243DQB , LTG5243DQC , LTG5243DT2 , LTG5243DT3 , LTG5243DT4 , LTG5243DT5 , LTG5243DT6 , LTG5243DT7 , LTG5243DT8 , LTG5243DZ1 , LTG5243DZ2 , WET4024EW0 , YLTE5243DQ2 , YLTE5243DQ3 , YLTE5243DQ4 , YLTE5243DQ5 , YLTE5243DQ6 , YLTE5243DQ7 , YLTE5243DQ8 , YLTE5243DQ9 , YLTE5243DQA , YLTE5243DQB , YWET4024EW0. This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less

XPARTCO WD01X29878 Dishwasher Door Latch – Compatible with GE Dishwashers Product Description Restore secure door closing and proper dishwasher operation with the XPARTCO WD01X29878 Dishwasher Door Latch. This high-quality aftermarket replacement ensures the dishwasher door locks firmly during wash cycles and signals the control board that it is safe to operate. A faulty door latch can cause the dishwasher not to start, stop mid-cycle, or display door-related error codes. Replacing it with this reliable XPARTCO latch helps restore safe and dependable washing performance. XPARTCO offers cost-effective aftermarket appliance parts engineered to match original fit and function. Replaces Part Numbers WD01X29878, WD01X27701, 265D1214G004, EG-380944, PD00072017, FIX16659468, 4979622, AP7176296, PS16659468. Compatibility This replacement dishwasher door latch fits select GE dishwashers. Common compatible models include (but are not limited to): GE GDT655SSJSS GE GDF630PGMWW Always verify your dishwasher’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and electrical function 🔒 Secure Door Locking – Ensures dishwasher runs only when door is properly closed ⚙️ Fixes Start Issues – Resolves no-start or cycle interruption problems 🧩 Direct-Fit Design – Installs without modification 💰 Cost-Effective Repair – Affordable alternative to OEM door latches 📐 Product Specification Part Number: WD01X29878 Component Type: Dishwasher Door Latch Assembly Function: Door locking and safety interlock Mounting: Screw-mounted, plug-in harness Application: Dishwasher door safety system Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver ⚠️ Safety First: Unplug the dishwasher or turn off the breaker before servicing to avoid electrical shock. Basic Steps: Disconnect dishwasher power. Remove the inner door panel screws. Locate and disconnect the old door latch assembly. Remove mounting screws and take out the latch. Install the new XPARTCO WD01X29878 latch. Reconnect wiring and reassemble the door panel. Restore power and test operation. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore secure dishwasher operation and prevent door-related errors — Add to Cart Now for a dependable, budget-friendly repair!

Read more less