EXP696 Dryer Drum Roller & Belt for Samsung Replaces DC97-16782A, 6602-001655
This Kit Included Following Parts:4 X Drum Rollers DC97-16782A 1 X Drum Belt 6602-001655
Drum Roller Replaces Part Numbers: DC97-16782A, AP5325135, DC97-16782C, DC97-16782D, 2027851, DC97-07523A, DC97-07523B, PS4221885, WPW10177428, AP6016361, W10177428, 35001136, DC97-07523A, PS11749648
Drum Belt Replaces: 6602-001655, AP4373659, 1935594, 6602-001314, PS4133825, WPW10205415, AP6017004, W10205415, 35001137, 6602-001314, PS11750299
This is an aftermarket part that can be used as a replacement for the OEM part.
12638000000786 Genuine OEM Midea Dryer Drum Roller
The 12638000000786 is a genuine Midea OEM dryer drum support roller. This roller sits underneath the drum, along its support track, and does the physical work of holding the drum's weight while letting it turn freely as the belt drives it around. A dryer typically uses more than one of these rollers working together to keep the drum properly supported and centered.
Over time, the wheel and bearing inside the roller wear down from the constant heat and rotation the dryer subjects them to, eventually developing a flat spot, seizing up, or simply wearing thin enough that the drum sits unevenly. A worn roller produces a distinctive symptom: a rumbling, squeaking, or thumping noise that rises and falls with drum rotation, often getting louder as a load tumbles or as the roller continues to wear.
Quick Answer
The 12638000000786 Genuine OEM Midea Dryer Drum Roller fixes Midea-built dryers with a rumbling, squeaking, or thumping noise that rises and falls with drum rotation. Supports and centers the drum along its support track.
Common Problems This Part Fixes
Rumbling or grinding noise that rises and falls with drum rotation
Squeaking or squealing noise from inside the dryer during operation
Thumping or knocking noise, especially with a heavier load
Noise that gets louder over time as the roller wears further
Drum that sits unevenly or wobbles slightly when turned by hand
Visible flat spot, cracking, or wear on the roller wheel
Noise that continues even with an empty drum tumbling
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
12638000000786, AP7155087, PS18170572
We were not able to confirm additional cross-reference or superseding part numbers for this specific part from reliable sources at the time this page was built, so none are listed here rather than guessed. This is a distinct part number from our 12638000004021 drum roller listing — the two are not interchangeable and do not cross-reference each other. If you have a cross-reference number for your appliance, contact our support team and we will verify compatibility before you order.
Compatibility
This drum roller is compatible with select Midea-built dryers.
Note: A specific verified compatible model list was not available at the time this page was built. Midea uses several different roller designs across its dryer lineup, and this part number is distinct from our 12638000004021 listing. Always verify your full model number before ordering. Contact our support team with your model number and we will confirm fitment before you purchase.
Key Features
Genuine Midea OEM part — factory-specified wheel and bearing design
Supports the drum along its support track, allowing smooth rotation as the belt drives it
Resolves "rumbling," "squeaking," and "thumping" noise symptoms caused by roller wear
Direct drop-in replacement for the original roller and axle assembly
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
12638000000786
Part Type
Dryer Drum Support Roller
Condition
Genuine OEM
Brand
Midea
Location
Drum support track
Function
Supports and centers the drum during rotation
Quantity
1 roller
Compatible Brand
Midea
Installation Notes
⚠️ Unplug Dryer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. On a gas model, also close the gas shutoff valve before moving the cabinet. Wear work gloves — sheet metal edges inside the cabinet are sharp. Access is typically through the rear panel: remove the screws securing the panel, then release the drum belt from the idler pulley to relieve tension so the drum can be supported and moved slightly for access to the rollers underneath. Photograph the roller and axle positions before removing anything. Remove the retaining clip or fastener holding the worn roller's axle in place, then slide the old roller off. Install the new 12638000000786 roller onto the axle in the same orientation, and secure it with the retaining clip or fastener. While you're in there, check the other rollers by spinning each one by hand — if any feel stiff, gritty, or worn, replace them at the same time, since they're typically the same age and wear on a similar schedule. Re-tension the belt around the idler pulley, reassemble the rear panel, restore power, and run a short empty cycle to confirm the noise has resolved. Tools needed: Phillips screwdriver, nut driver, pliers, work gloves.
Frequently Asked Questions
My dryer makes a rumbling noise that gets louder over time. Is this the part I need?
Yes, this is the classic symptom of a worn drum roller. As the wheel and bearing wear down, the noise typically starts subtle and gradually worsens, often becoming most noticeable with a full load as the extra weight puts more load on the worn wheel. If the noise rises and falls in rhythm with the drum turning, a roller is the most likely cause.
Is this the same roller as your 12638000004021 listing?
No. These are two distinct Midea part numbers, and they do not cross-reference or replace each other. If you're not sure which roller your dryer uses, check the number stamped on your existing roller or contact our support team with your model number, and we'll confirm which one is correct before you order.
Should I replace just one roller, or all of them?
It's worth checking all of them while you have access. Dryers typically use more than one roller supporting the drum, and since they're the same age and under the same stress, if one has worn out the others are often not far behind. Spin each roller by hand — if any feel stiff, gritty, or rough, replace them together to avoid repeating this repair again soon.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Midea to factory specifications — guaranteed fit, materials, and performance. It matches the original wheel design, bearing, and axle fitment of the drum roller originally installed in your dryer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
2 Pack - 12638000000786 Genuine OEM Midea Dryer Drum Roller
The 12638000000786 is a genuine Midea OEM dryer drum support roller. This roller sits underneath the drum, along its support track, and does the physical work of holding the drum's weight while letting it turn freely as the belt drives it around. A dryer typically uses more than one of these rollers working together to keep the drum properly supported and centered.
Over time, the wheel and bearing inside the roller wear down from the constant heat and rotation the dryer subjects them to, eventually developing a flat spot, seizing up, or simply wearing thin enough that the drum sits unevenly. A worn roller produces a distinctive symptom: a rumbling, squeaking, or thumping noise that rises and falls with drum rotation, often getting louder as a load tumbles or as the roller continues to wear.
Quick Answer
The 12638000000786 Genuine OEM Midea Dryer Drum Roller fixes Midea-built dryers with a rumbling, squeaking, or thumping noise that rises and falls with drum rotation. Supports and centers the drum along its support track.
Common Problems This Part Fixes
Rumbling or grinding noise that rises and falls with drum rotation
Squeaking or squealing noise from inside the dryer during operation
Thumping or knocking noise, especially with a heavier load
Noise that gets louder over time as the roller wears further
Drum that sits unevenly or wobbles slightly when turned by hand
Visible flat spot, cracking, or wear on the roller wheel
Noise that continues even with an empty drum tumbling
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
12638000000786, AP7155087, PS18170572
We were not able to confirm additional cross-reference or superseding part numbers for this specific part from reliable sources at the time this page was built, so none are listed here rather than guessed. This is a distinct part number from our 12638000004021 drum roller listing — the two are not interchangeable and do not cross-reference each other. If you have a cross-reference number for your appliance, contact our support team and we will verify compatibility before you order.
Compatibility
This drum roller is compatible with select Midea-built dryers.
Note: A specific verified compatible model list was not available at the time this page was built. Midea uses several different roller designs across its dryer lineup, and this part number is distinct from our 12638000004021 listing. Always verify your full model number before ordering. Contact our support team with your model number and we will confirm fitment before you purchase.
Key Features
Genuine Midea OEM part — factory-specified wheel and bearing design
Supports the drum along its support track, allowing smooth rotation as the belt drives it
Resolves "rumbling," "squeaking," and "thumping" noise symptoms caused by roller wear
Direct drop-in replacement for the original roller and axle assembly
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
12638000000786
Part Type
Dryer Drum Support Roller
Condition
Genuine OEM
Brand
Midea
Location
Drum support track
Function
Supports and centers the drum during rotation
Quantity
1 roller
Compatible Brand
Midea
Installation Notes
⚠️ Unplug Dryer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. On a gas model, also close the gas shutoff valve before moving the cabinet. Wear work gloves — sheet metal edges inside the cabinet are sharp. Access is typically through the rear panel: remove the screws securing the panel, then release the drum belt from the idler pulley to relieve tension so the drum can be supported and moved slightly for access to the rollers underneath. Photograph the roller and axle positions before removing anything. Remove the retaining clip or fastener holding the worn roller's axle in place, then slide the old roller off. Install the new 12638000000786 roller onto the axle in the same orientation, and secure it with the retaining clip or fastener. While you're in there, check the other rollers by spinning each one by hand — if any feel stiff, gritty, or worn, replace them at the same time, since they're typically the same age and wear on a similar schedule. Re-tension the belt around the idler pulley, reassemble the rear panel, restore power, and run a short empty cycle to confirm the noise has resolved. Tools needed: Phillips screwdriver, nut driver, pliers, work gloves.
Frequently Asked Questions
My dryer makes a rumbling noise that gets louder over time. Is this the part I need?
Yes, this is the classic symptom of a worn drum roller. As the wheel and bearing wear down, the noise typically starts subtle and gradually worsens, often becoming most noticeable with a full load as the extra weight puts more load on the worn wheel. If the noise rises and falls in rhythm with the drum turning, a roller is the most likely cause.
Is this the same roller as your 12638000004021 listing?
No. These are two distinct Midea part numbers, and they do not cross-reference or replace each other. If you're not sure which roller your dryer uses, check the number stamped on your existing roller or contact our support team with your model number, and we'll confirm which one is correct before you order.
Should I replace just one roller, or all of them?
It's worth checking all of them while you have access. Dryers typically use more than one roller supporting the drum, and since they're the same age and under the same stress, if one has worn out the others are often not far behind. Spin each roller by hand — if any feel stiff, gritty, or rough, replace them together to avoid repeating this repair again soon.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Midea to factory specifications — guaranteed fit, materials, and performance. It matches the original wheel design, bearing, and axle fitment of the drum roller originally installed in your dryer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
2 Pack - 12638000004021 Genuine OEM Midea Dryer Drum Roller
The 12638000004021 is a genuine Midea OEM dryer drum support roller, sold under the Frigidaire/Midea manufacturing relationship for Midea-built dryers and select Frigidaire, Insignia, and Kenmore dryers using this same platform. This roller sits underneath the drum, along its rear support track, and does the physical work of holding the drum's weight while letting it turn freely as the belt drives it around. A dryer typically uses more than one of these rollers working together to keep the drum properly supported and centered.
Over time, the wheel and bearing inside the roller wear down from the constant heat and rotation the dryer subjects them to, eventually developing a flat spot, seizing up, or simply wearing thin enough that the drum sits unevenly. A worn roller produces a distinctive symptom: a rumbling, squeaking, or thumping noise that rises and falls with drum rotation, often getting louder as a load tumbles. It directly replaces 5304511415, AP7990985.
Quick Answer
The 12638000004021 Genuine OEM Midea Dryer Drum Roller fixes Midea-built dryers (and select Frigidaire, Insignia, and Kenmore dryers on this platform) with a rumbling, squeaking, or thumping noise that rises and falls with drum rotation. Supports and centers the drum on its rear track. Replaces 5304511415, AP7990985.
Common Problems This Part Fixes
Rumbling or grinding noise that rises and falls with drum rotation
Squeaking or squealing noise from inside the dryer during operation
Thumping or knocking noise, especially with a heavier load
Noise that gets louder over time as the roller wears further
Drum that sits unevenly or wobbles slightly when turned by hand
Visible flat spot, cracking, or wear on the roller wheel
Noise that continues even with an empty drum tumbling
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer drum roller directly replaces the following OEM and cross-reference part numbers:
12638000004021, AP7990985, PS18170578, 5304511415, 4056012471, AP8049485, PS17993389.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drum roller is compatible with select Midea-built dryers, and also fits select Frigidaire, Insignia, and select Kenmore dryers built on the same Midea platform.
Note: Always verify your full model number before ordering, since Midea and its partner brands use several different roller designs across their dryer lineup. Contact our support team with your model number if you're unsure.
Key Features
Genuine Midea OEM part — factory-specified wheel and bearing design
Supports the drum along its rear track, allowing smooth rotation as the belt drives it
Resolves "rumbling," "squeaking," and "thumping" noise symptoms caused by roller wear
Direct drop-in replacement for the original roller and axle assembly
Replaces 5304511415, AP7990985.
Compatible with Midea, Frigidaire, Insignia, and select Kenmore dryers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
12638000004021
Part Type
Dryer Drum Support Roller
Condition
Genuine OEM
Brand
Midea
Location
Rear drum support track
Function
Supports and centers the drum during rotation
Quantity
1 roller
Compatible Brands
Midea, Frigidaire, Insignia, Kenmore
Installation Notes
⚠️ Unplug Dryer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. On a gas model, also close the gas shutoff valve before moving the cabinet. Wear work gloves — sheet metal edges inside the cabinet are sharp. Access is typically through the rear panel: remove the screws securing the panel, then release the drum belt from the idler pulley to relieve tension so the drum can be supported and moved slightly for access to the rollers underneath. Photograph the roller and axle positions before removing anything. Remove the retaining clip or fastener holding the worn roller's axle in place, then slide the old roller off. Install the new 12638000004021 roller onto the axle in the same orientation, and secure it with the retaining clip or fastener. While you're in there, check the other rollers by spinning each one by hand — if any feel stiff, gritty, or worn, replace them at the same time, since they're typically the same age and wear on a similar schedule. Re-tension the belt around the idler pulley, reassemble the rear panel, restore power, and run a short empty cycle to confirm the noise has resolved. Tools needed: Phillips screwdriver, nut driver, pliers, work gloves.
Frequently Asked Questions
My dryer makes a rumbling noise that gets louder over time. Is this the part I need?
Yes, this is the classic symptom of a worn drum roller. As the wheel and bearing wear down, the noise typically starts subtle and gradually worsens, often becoming most noticeable with a full load as the extra weight puts more load on the worn wheel. If the noise rises and falls in rhythm with the drum turning, a roller is the most likely cause.
Should I replace just one roller, or all of them?
It's worth checking all of them while you have access. Dryers typically use more than one roller supporting the drum, and since they're the same age and under the same stress, if one has worn out the others are often not far behind. Spin each roller by hand — if any feel stiff, gritty, or rough, replace them together to avoid repeating this repair again soon.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Midea to factory specifications — guaranteed fit, materials, and performance. It matches the original wheel design, bearing, and axle fitment of the drum roller originally installed in your dryer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
349241T Genuine OEM Dryer Drum Roller Kit - Compatible with Whirlpool, Kenmore, Maytag
Restore smooth and quiet operation to your dryer with the 349241T Genuine OEM Dryer Drum Roller Kit. This Whirlpool-manufactured kit includes two drum rollers, four tri-rings, and one retaining washer, designed to support the drum in select Whirlpool, Kenmore, Maytag, and other compatible dryers. It addresses issues like excessive noise, vibration, or drum not tumbling, ensuring efficient drying performance. Recommended to replace both rollers at once for optimal results.
This set includes 2 drum rollers, 4 tri-ring retaining clips, and 2 retaining washers — everything needed for a complete rear roller replacement. Each roller measures 3-1/4"L x 1"W x 3-1/4"H and is constructed from rubber over a metal bearing hub with a plastic axle support. Both rollers must always be replaced at the same time. The set directly replaces 349241, 349241TVP, 8170, 8205, 337089, 340352, 661562, 3389901, 3397588, 3397590, AP3098345, PS347627, and several additional cross-reference numbers. Often replaced together with the drum belt (341241) and idler pulley (691366 or 279640) for a complete drum drive repair. Installs in 30–60 minutes with basic hand tools.
Quick Answer
349241T Genuine OEM Dryer Drum Roller Kit. This Whirlpool-manufactured kit includes two drum rollers, four tri-rings, and one retaining washer, designed to support the drum in select Whirlpool, Kenmore, Maytag, and other compatible dryers. It addresses issues like excessive noise, vibration, or drum not tumbling, ensuring efficient drying performance. Recommended to replace both rollers at once for optimal results. Replaces 349241, 8170, 8205, 337089, 3389901, AP3098345, PS347627.
Common Problems This Part Fixes
Loud thumping, rumbling, or squealing noise during the drying cycle
Grinding or scraping sound when the drum is turning
Drum turning unevenly or wobbling during operation
Drum not spinning — rollers so worn they can no longer support the drum
Squealing or squeaking that gets worse over time as roller bearings degrade
Marks or scuff lines on clothes — drum dragging against the dryer cabinet
Excessive vibration during the drying cycle
Replaces Part Numbers
This drum roller set directly replaces the following OEM and cross-reference part numbers:
349241T, 26000349241, 337089, 3389901, 3397588, 3397590, 340352, 3436, 349241, 349241TVP, 661562, 8170, 8205, 99989678, 99989679, AH347627, EA347627, K34-895, AWP39168, PD00002257, EAP347627, AP3098345, PS347627.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drum roller set is compatible with select 29-inch gas and electric dryers from the following brands:
Whirlpool dryers (gas and electric — 29" models)
Kenmore / Sears dryers (Whirlpool-built models)
Maytag dryers
KitchenAid dryers
Amana dryers
Roper dryers
Crosley dryers
Estate dryers
Inglis dryers
Admiral dryers
Magic Chef dryers
Note: The 349241T rollers are for 29-inch Whirlpool-family dryers. Newer Whirlpool Duet front-load dryers and larger-capacity models use different roller part numbers (such as WPW10314173 / 8536974). Always verify your model number before ordering.
Key Features
Set of 2 rear drum support rollers — supports and cradles the drum as it rotates for smooth, quiet operation
Includes all hardware: 2 rollers, 4 tri-ring retaining clips, 2 retaining washers — everything needed for a complete installation
Dimensions: 3-1/4"L x 1"W x 3-1/4"H per roller
Rubber wheel over metal bearing hub with plastic axle support — designed to resist wear and heat under continuous drum load
Both rollers must be replaced at the same time — replacing only one results in uneven drum support and accelerated wear on the new roller
Often replaced together with the drum belt (341241) and idler pulley (691366 or 279640) for a complete drum drive repair
Compatible with 11 major appliance brands on the Whirlpool 29-inch platform
Dryer Genuine OEM Part.
DIY repair — installs in 30–60 minutes with basic hand tools
Product Specifications
Part Number
349241T
Part Type
Dryer Rear Drum Support Roller Set
Condition
Genuine Whirlpool OEM
Application
29-inch Gas and Electric Dryers
Quantity
Set of 2 rollers (replace both at the same time)
Roller Dimensions
3-1/4"L x 1"W x 3-1/4"H (per roller)
Material
Rubber wheel / Metal bearing hub / Plastic axle support
Color
Black / White
Kit Includes
2 drum rollers, 4 tri-ring retaining clips, 2 retaining washers
Often Replaced With
341241 Drum Belt, 691366 or 279640 Idler Pulley
Compatible Brands
Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef
Installation Notes
⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the lint screen and unscrew the screws inside the lint screen housing. Use a putty knife to release the top panel spring clips and lift the top panel. Remove the front panel to access the drum. Release the drive belt from the idler pulley, lift the drum forward, and set it aside. The rear drum support rollers are mounted on shafts on the rear bulkhead — each roller is secured with a tri-ring clip and a retaining washer. Use needle-nose pliers to remove the old tri-ring clips, then slide the old rollers off the shafts. Install the new rollers, new retaining washers, and new tri-ring clips on the shafts. Reinstall the drum, re-route the belt around the motor and idler pulley, and reassemble the front and top panels. Restore power and run a test cycle to verify quiet, smooth drum operation. Tip: while the dryer is open, inspect and replace the drum belt (341241) and idler pulley (691366 or 279640) if worn. Tools needed: Phillips screwdriver, 1/4" or 5/16" nut driver, putty knife, needle-nose pliers.
Frequently Asked Questions
What do the drum support rollers do?
The rear drum support rollers are cylindrical wheels mounted on fixed shafts at the back of the dryer cabinet. As the drum rotates, its rear outer rim rests on these rollers, which carry the drum's weight and allow it to spin smoothly and quietly. When the rubber wheels wear down or the bearing hubs corrode, the drum no longer rides smoothly on the rollers — causing thumping, rumbling, or squealing noises that get progressively worse. In severe cases, worn rollers allow the drum to sag and drag against the cabinet rear panel.
Why must I replace both rollers at the same time?
Both rear drum support rollers carry the same load and experience the same wear through every drying cycle. When one roller fails, the other has been under the same stress for the same number of cycles and is almost certainly near the end of its useful life. Replacing only the failed roller leaves one worn roller supporting the drum unevenly, which puts extra stress on the new roller and causes it to wear out much faster. Replace both rollers at the same time to ensure even drum support and get the full service life from the new parts.
Should I also replace the belt and idler pulley at the same time?
Yes — this is the ideal time. Since the dryer must be fully disassembled to access the rear drum rollers, replacing the drum belt (341241) and idler pulley (691366 or 279640) at the same time is strongly recommended. All three parts wear at similar rates, and a worn belt or idler pulley is often what caused the rollers to wear prematurely. Doing all three in one repair eliminates the most common drum drive failure points and saves you from repeating the teardown in the near future. The 4392065 maintenance kit includes all three parts together.
What causes dryer drum rollers to wear out?
Drum rollers wear naturally over time from the continuous load of supporting the rotating drum. The most common accelerating factors are operating the dryer with a worn or broken belt (which allows the drum to sag and puts extra weight on the rollers), running very large or heavy loads frequently, and allowing lint to accumulate around the roller shafts, which causes the bearings to run dry and wear faster. Regular dryer maintenance — including cleaning lint from around the drum and periodically checking the belt — helps extend roller life.
Is this an OEM or aftermarket part?
It is a genuine Whirlpool OEM part.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 22003483 Washer Drive Belt
The XPARTCO 22003483 is an aftermarket replacement drive belt for Whirlpool-built Maytag Atlantis top-load washers. This belt is the mechanical link between the drive motor and the washer's drive system — it's what actually transmits the motor's rotation to spin the drum, so both agitation and spin depend entirely on this belt gripping its pulleys correctly and staying properly tensioned.
Made of black rubber, this belt measures 52 inches long. Over years of use, the belt material gradually hardens and glazes over, becoming smooth and "slick" rather than gripping the pulleys firmly — this degradation can cause the belt to slip under load even before it shows any visible cracking or damage. A worn belt produces a range of symptoms depending on how far the wear has progressed: the washer may pump water but fail to spin, fail to agitate at all, spin noticeably slower than normal, or produce a chirping or slipping noise, especially as the motor shifts between wash and spin modes. It directly replaces WP22003483, WP22003483VP, AP6006365, PS11739438, 22002709, 62608400, 62618130, and 824667.
Quick Answer
The XPARTCO 22003483 Washer Drive Belt fixes Maytag (Whirlpool-built) top-load washers that pump but won't spin, won't agitate, spin slowly, or make a chirping/slipping noise as the motor shifts modes. 52 inches long, black rubber. Replaces WP22003483, WP22003483VP, AP6006365, PS11739438, 22002709, 62608400, 62618130, 824667. A belt can slip and cause symptoms well before it looks visibly worn — years of use leave the rubber "slick" and unable to grip the pulleys properly, even without visible cracking.
Common Problems This Part Fixes
Washer pumps water but won't spin
Washer won't agitate
Washer spins noticeably slower than it used to
Chirping or slipping noise, especially as the motor shifts between wash and spin modes
Belt that has become glazed, hardened, or "slick" from years of use
Visible cracking, fraying, or glazing on the belt surface
General noise or vibration during the wash or spin cycle
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer drive belt directly replaces the following OEM and cross-reference part numbers:
WP22003483 22003483, 22002709, 62618130, 824667, AP6006365, EAP11739438, WP22003483VP, AWP47150, PD00002551, PS11739438
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drive belt is compatible with select Maytag Atlantis top-load washers built on the Whirlpool platform, including model numbers such as:
MAV4057AWQ, MAV4057AWW, MAV4500AWW
MAV5000AWQ, MAV5000AWW, MAV5057AWQ, MAV5057AWW, MAV5960AWW
MAV6000AWQ, MAV6000AWW, MAV6057AWQ, MAV6057AWW
MAV6200AWQ, MAV6200AWW, MAV6250AWQ, MAV6250AWW, MAV6257AWQ, MAV6257AWW
MAV6548AWQ, MAV6548AWW, MAV6601AWQ, MAV6601AWW, MAV6650AWW, MAV7000AWQ
Note: Always verify your full model number before ordering, since Whirlpool and Maytag use different belt lengths and profiles across their washer lineup. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement drive belt — transmits motor power to spin the washer drum
Resolves "pumps but won't spin," "won't agitate," "spins slowly," and "chirping/slipping noise" symptoms caused by belt wear
52 inches long, black rubber construction
Rides on three pulleys to transfer motor rotation to the drive system
Direct drop-in replacement matching the original length and profile
Replaces WP22003483, WP22003483VP, AP6006365, PS11739438, 22002709, 62608400, 62618130, and 824667
Compatible with Maytag Atlantis top-load washers built on the Whirlpool platform
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
22003483
OEM Part Number
WP22003483
Part Type
Washer Drive Belt
Condition
Aftermarket Replacement
Application
Maytag Atlantis Top-Load Washers (Whirlpool-Built)
Length
52 inches
Material
Rubber
Color
Black
Function
Transmits motor rotation to the drive system to spin the drum
Quantity
1 drive belt
Compatible Brand
Maytag (Whirlpool-built)
Installation Notes
⚠️ Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel: remove the screws securing the panel to reach the motor and belt area. Loosen the motor's mounting screws so the motor can be pushed toward the drum, releasing tension on the old belt. Slide the old belt off its three pulleys and remove it. Route the new 22003483 belt over the same three pulleys, matching the original path. With the belt in place, gently push the motor away from the drum by hand to apply tension, then tighten the motor's mounting screws while continuing to check belt tightness — the belt should have firm, even tension across all three pulleys with no excess slack. Reinstall the rear panel, restore power, and run a full test cycle through both agitate and spin to confirm smooth, quiet operation with no chirping or slipping. Tools needed: Phillips screwdriver, nut driver, work gloves.
Frequently Asked Questions
My washer makes a chirping noise when it shifts from agitate to spin. Is that the belt?
Yes, this is a documented symptom of a worn belt. One long-term owner traced this exact chirp to a 10-year-old belt that had become "slick" from age — smooth and hardened enough that it briefly slipped on the pulleys as the motor shifted between modes, rather than moving cleanly into position. Replacing the belt resolved the noise completely.
My belt doesn't look cracked or damaged. Could it still be the problem?
Yes. A belt can degrade in ways that aren't obvious at a glance — the rubber can harden and glaze over time, becoming slick and losing its grip on the pulleys even without visible cracking or fraying. If your washer is slipping, chirping, or spinning weakly and the belt has been in service for many years, age-related slickness is a reasonable explanation even if the belt still looks intact.
How do I know if I have the right belt length for my washer?
This belt is 52 inches long and specific to the Maytag Atlantis top-load platform. Whirlpool and Maytag use different belt lengths across other washer models, so always confirm your model number matches the compatibility list, or measure your old belt for comparison, before ordering.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the length, profile, and material of the original WP22003483 drive belt used in compatible Maytag Atlantis top-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 5304516132 Washer Drive Belt – Compatible with Frigidaire, Electrolux, and Kenmore Washers
Product Description
Keep your washer spinning smoothly with the XPARTCO 5304516132 Washer Drive Belt. This high-quality aftermarket replacement transfers power from the motor to the washer drum, enabling proper agitation and spin speed. A worn, stretched, or broken belt can cause slow spinning, loud noises, or the drum not turning at all. Replacing it with this durable XPARTCO belt restores reliable performance and efficient wash cycles.
Replaces Part Numbers
5304516132, 12638000001161, 7PJE607, PD00055739, EAP12585162, 4839724, AP6339955, PS12585162.
Compatibility
This replacement drive belt fits select Frigidaire, Electrolux, and Kenmore front-load washers.
Example compatible models include (but are not limited to): Frigidaire FAFW3801LW, Electrolux EWFLS70JSS0, and Kenmore 417.41122310.
Always verify your washer's model number before ordering. Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Matches OEM fit and performance at a lower cost
⚙️ Restores Drum Motion – Ensures proper spinning, agitation, and wash performance
💪 Durable Construction – Made with reinforced rubber for long-lasting tension
🛠️ Easy Installation – Designed for quick DIY replacement
🛡️ Fixes Common Issues – Solves slow spinning, no spin, squealing noises, or drum not turning
📐 Product Specification
Part Number: 5304516132
Component Type: Washer Drive Belt
Material: Reinforced rubber with tension-resistant cord
Dimensions: Exact OEM-equivalent sizing for proper tension
Mounting: Wraps around motor pulley and drum pulley
Compliance: Built to OEM-equivalent quality standards (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, nut driver (depending on model)
⚠️ Safety First: Always unplug the washer before servicing to avoid electrical shock.
Steps:
Unplug the washer and remove the rear access panel.
Locate the old drive belt and remove it from the motor and drum pulleys.
Position the new XPARTCO 5304516132 belt around the drum pulley first.
Stretch the belt onto the motor pulley while rotating the drum.
Reinstall the back panel, restore power, and test wash/spin cycles.
⏱️ Time Required: 10–20 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Appliance Parts Supplier
🔄 30-Day Return Policy
Restore smooth washer performance — Add to Cart Now for a dependable, affordable repair!
WH01X27538 Washer Drive Belt - Compatible with GE, Hotpoint, Haier Washers
Product Description
Restore your washer’s performance with the replacement WH01X27538 Washer Drive Belt. This high-quality replacement multi-rib belt replaces the GE WH01X27538, designed for select GE, Hotpoint, Haier, Monogram, and Café top-load washing machines. Measuring approximately 22.87" long with 5 ribs and 4 grooves, this durable rubber belt connects the drive motor to the washer drum, enabling proper agitation and spin cycles. It fixes issues like the drum not spinning, loud noises (squeaking or thumping), burning odors, or the washer stopping mid-cycle. Note: Inspect the motor pulley and transmission for wear or oil leaks, as these can cause belt slippage. The belt is a tight fit for durability; use vice grips or a second person to assist installation.
Replaces part numbers: WH01X27538, 290D1101P005, 4587903, AP6328256, PS12299369.
Compatibility:
Compatible with models including but not limited to:
GE: GTW220ACK4WW, GTW220ACK5WW, GTW220ACK6WW, GTW330ASK3WW, GTW330ASK4WW, GTW335ASN0WW, GTW335ASN1WW, GTW460ASJ8WW, GTW460ASJ9WW, GTW465ASN1WW, GTW465ASN3WW, GTW585BSV0WS
Hotpoint: HTW200ASK3WW, HTW200ASK4WW, HTW240ASK3WS, HTW240ASK4WS, HTW240ASK5WS
Haier, Monogram, Café: Select top-load washer models
Verify your model number or contact support for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select GE, Hotpoint, Haier, Monogram, and Café top-load washer models.
🔥 Specifications: Multi-rib belt, 22.87" long, 5 ribs, 4 grooves, made of durable rubber with reinforced construction for stretch resistance.
💰 Cost-Effective Alternative: Aftermarket belt offers OEM-equivalent performance at a lower price.
🛠️ Easy Installation: Requires a Phillips screwdriver, pliers, vice grips, and work gloves; typically installed in 15–30 minutes.
🛡️ Reliable Fixes: Resolves issues like drum not spinning, no agitation, loud noises, burning odor, or washer stopping mid-cycle.
Safety First: Unplug the washer from the power source and shut off the water supply before installation.
Shop for high-quality replacement appliance parts with a 30-day return policy. Get your washer back to smooth, efficient performance today!
Add to cart now for a budget-friendly fix!
WH01X24697 Washer Drive Belt – Replacement for GE and Hotpoint Washers
Product Overview
This drive belt is a exact replacement part for specific GE washing machine models. The Drive Belt is responsible for rotating the drum of the washing machine, allowing for the proper washing and spinning of clothes. A faulty or broken Drive Belt can result in the drum not spinning properly or not spinning at all. This results in such issues as clothes not being cleaned or water not draining properly.
533J5, 21" long.
Replaces Part Numbers
Replaces WH01X24697, AP6037512, PS11767488.
Engineered to meet or exceed OEM performance and fit specifications.
Compatible Brands
Compatible with GE and Hotpoint top-load washers, as well as select Haier, Hotpoint, models manufactured by GE. Fits machines that require this specific drive belt configuration.
Fixes the Following Issues
Washer won’t spin or agitate
Squealing or slipping sounds during operation
Loose or broken drive belt
Poor washing or draining performance
Why Buy from Parts‑O‑Matic
Cost-effective aftermarket alternative
Fast and free U.S. shipping
Trusted by appliance repair professionals and DIY users
Easy to install – no special tools required
EXP651 Dryer Belt and Idler Pulley Kit Replaces WPW10112954, W10837240
The EXP651 is an aftermarket dryer repair kit containing two essential drum drive components for select Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, and Roper dryers. The kit includes one drum belt (replaces WPW10112954) and one idler pulley assembly with bracket (replaces W10837240) — the two parts most commonly worn together when a dryer drum stops spinning or becomes noisy.
Replacing both the belt and idler pulley at the same time is the smart repair choice. Since the dryer must be disassembled to access either part, doing both in one repair saves you from having to take the machine apart again if the second part fails shortly after. This kit covers the two most common failure points in the Whirlpool-family dryer drum drive system.
Quick Answer
The EXP651 Dryer Belt and Idler Pulley Kit fixes dryers where the drum is not spinning, making loud squeaking or grinding noises, or the belt has broken. Includes one 93-1/4" x 5/16" 5-rib drum belt (WPW10112954) and one idler pulley assembly with bracket (W10837240). Compatible with select Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, and Roper dryers.
What's in the Kit
Part 1 of 2
Dryer Drum Belt — Replaces WPW10112954
93-1/4" L x 5/16" W x 1/8" H · 5-rib Multi-V rubber belt · Wraps around drum and connects to motor and idler pulleys to drive drum rotation
Part 2 of 2
Idler Pulley Assembly with Bracket — Replaces W10837240
2-1/8" pulley diameter · 6-1/4" L x 1-1/4" W x 3-7/16" H overall · Plastic/metal construction · Maintains correct belt tension to spin the drum · Fits Whirlpool dryers with lint screen inside door
Common Problems This Kit Fixes
Dryer drum not spinning — motor runs but drum stays still
Loud squeaking, squealing, or grinding noise during operation
Clothes not tumbling during the drying cycle
Thumping or slapping noise when dryer is running
Belt slipping off or repeatedly breaking
Burning rubber smell coming from the dryer
Dryer drum turning erratically or stopping while motor continues to run
Replaces Part Numbers
Drum Belt (WPW10112954) cross-references:
WPW10112954, W10112954, 1447719, AWP48873, PD00003553, EAP11748388, AP6015116, PS11748388.
Idler Pulley Assembly (W10837240) cross-references:
W10837240, W10547287, W10547290, 3387372, 3388674, W10118754, W10118756, W10837240VP, AWP41730, PD00025564, FIX11726337, AP5988716, PS11726337, 279640, AP3094197, 279640VP, 2958, 3388672, 697692, TJ279640, W10468057, AH334244, EA334244, ER279640, PS334244.
If your part numbers are not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This kit is compatible with select dryers from the following brands:
Whirlpool dryers (gas and electric — fits models with lint screen inside door)
Maytag dryers (gas and electric)
Amana dryers
Kenmore / Sears dryers (select Whirlpool-built models)
KitchenAid dryers
Crosley dryers
Admiral dryers
Inglis dryers
Roper dryers
Note: The W10837240 idler pulley fits Whirlpool-family dryers with the lint screen located inside the door. If your dryer has the lint screen on top of the cabinet, a different idler pulley part number may be required. Contact our support team to confirm before ordering.
Key Features
Two-part kit covers the most common drum drive failures in Whirlpool-family dryers in a single repair
Belt: 93-1/4" L x 5/16" W, 5-rib Multi-V rubber — resists cracking, stretching, and heat damage
Idler pulley: 2-1/8" diameter pulley with arm and bracket — maintains correct belt tension for smooth drum rotation
Replacing both parts together saves a second disassembly if the other part fails soon after
Aftermarket replacement built to OEM-equivalent quality standards
Belt directly replaces WPW10112954 / W10112954 — no modification required
Idler pulley directly replaces W10837240 / W10547287 / W10547290 — no modification required
DIY-friendly repair — installs in 30–60 minutes with basic hand tools
Product Specifications
Kit Part Number
EXP651
Condition
Aftermarket Replacement
Application
Gas and Electric Dryers
Kit Includes
1x Drum Belt (WPW10112954), 1x Idler Pulley Assembly with Bracket (W10837240)
Belt Length
93-1/4 inches
Belt Width
5/16 inch
Belt Height
1/8 inch
Belt Ribs
5 ribs, 4 grooves (Multi-V)
Belt Material
Rubber
Pulley Diameter
2-1/8 inches
Pulley Overall Dimensions
6-1/4" L x 1-1/4" W x 3-7/16" H
Pulley Material
Plastic / Metal
Compatible Brands
Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, Roper
Installation Notes
⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen, then unscrew the Phillips screws inside the lint screen housing. Use a putty knife to release the top panel clips and lift the top panel. Remove the front panel to access the drum and drive components. Release belt tension at the old idler pulley, lift the drum slightly, and slide the old belt off. Remove the old idler arm assembly by unscrewing the mounting screw, then install the new W10837240 idler pulley assembly and secure with the screw. Loop the new WPW10112954 belt around the drum with the ribbed side facing inward, then route it around the new idler pulley and motor pulley. Consult your model's service manual or a model-specific repair video for the correct belt path. Reassemble and run a test cycle. Tools needed: Phillips screwdriver, putty knife or flat pry tool.
Frequently Asked Questions
Why should I replace the belt and idler pulley at the same time?
The belt and idler pulley wear together — when one fails, the other is usually close behind. Since the dryer must be fully disassembled to access either part, replacing both in a single repair saves you from having to take the machine apart again soon after. It also protects the new belt from being damaged by a worn pulley, and vice versa.
How does the W10837240 differ from other Whirlpool idler pulleys?
The W10837240 is the updated idler pulley arm and bracket assembly designed for Whirlpool-family dryers that have the lint screen inside the door. It replaces the older W10547287 and W10547290 assemblies. Some older or different Whirlpool models use a different idler pulley style — if you're unsure which one your dryer needs, contact our support team with your model number before ordering.
What is the difference between WPW10112954 and W10112954?
These are the same belt. WPW10112954 is the updated Whirlpool OEM part number that superseded the original W10112954. Both refer to the identical drum belt included in this kit.
Should I also replace the drum rollers at the same time?
It depends on the condition of your rollers. Since the dryer is already fully disassembled, it is a good opportunity to inspect the drum support rollers for flat spots, cracks, or wobbling. If they show any wear, replacing them at the same time is recommended to avoid a third disassembly. Check your model's roller part number before ordering.
Are these OEM or aftermarket parts?
Both parts in this kit are aftermarket replacements built to OEM-equivalent quality standards. They are not genuine Whirlpool OEM parts, but are manufactured to match the dimensions and performance of the original WPW10112954 belt and W10837240 idler pulley assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO Y54414 Dryer Idler Pulley Wheel – Replaces WPY54414 – Compatible with Maytag, Whirlpool & Kenmore Dryers
Product Description
Restore proper belt tension and smooth drum rotation with the XPARTCO Y54414 Dryer Idler Pulley Wheel. This high-quality aftermarket replacement pulley maintains tension on the dryer drum belt, ensuring consistent tumbling during drying cycles.
A worn or damaged idler pulley wheel can cause squealing noises, belt slippage, drum not turning, or uneven drying. Replacing it with this durable XPARTCO pulley helps eliminate noise issues and restore reliable dryer performance at a cost-effective price.
XPARTCO provides trusted aftermarket appliance parts engineered to match original fit and function.
Replaces Part Numbers
WPY54414, Y54414, 14218926, 54414, R0609504, WPY54414VP, 54414-REPL, R0609504-REPL, AP6024203, PS11757553, D510142P, 510142P, 510142, D510142, 510142P, 510142, 54414, 54415, 54415P, AP6329060, PS17001032, DE407, 54414-2, 1246423, AP6024203, EAP11757553, PD00002420, PS11757553, 510142P, 510142, D510142P, AP4291235, PS2200898
Compatibility
This replacement dryer idler pulley wheel fits select Maytag, Whirlpool, Kenmore (Whirlpool/Maytag-manufactured), Amana, Estate, and Crosley dryers.
Common compatible models include (but are not limited to):
Maytag MEDC215EW
Whirlpool WED4815EW
Kenmore 110.60612990
Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Matches OEM fit and belt alignment
🌀 Maintains Proper Belt Tension – Ensures smooth drum rotation
🔇 Reduces Squealing & Noise – Replaces worn or noisy pulley wheels
💪 Durable Bearing Design – Built for long service life
💰 Cost-Effective Repair – Affordable alternative to OEM idler pulleys
📐 Product Specification
Part Number: Y54414
Component Type: Dryer Idler Pulley Wheel
Material: Metal wheel with durable bearing
Application: Dryer drum belt tension system
Mounting: Shaft-mounted on idler arm
Quality Level: Aftermarket replacement (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, nut driver
⚠️ Safety First: Unplug the dryer before servicing to avoid electrical shock.
Basic Steps:
Disconnect dryer power.
Remove top and front panels to access drum (model dependent).
Release belt tension and remove the old pulley wheel.
Install the new XPARTCO Y54414 pulley onto the idler arm.
Re-route the belt around the motor pulley and idler.
Reassemble the dryer and test operation.
⏱️ Time Required: 30–45 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Aftermarket Appliance Parts
🔄 30-Day Return Policy
Eliminate dryer noise and restore smooth tumbling — Add to Cart Now for a reliable, budget-friendly repair!
