Search results for "Dryer timer"

XPARTCO EXP570 Dryer Door Latch Kit The XPARTCO EXP570 is an aftermarket replacement door catch and strike kit for dryers from Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis, LG, and other comparable brands. The catch and strike work as a pair: the strike on the dryer door engages the catch on the cabinet to hold the door shut for the whole cycle. When either part wears, cracks, or gets knocked out of alignment, the door stops latching reliably. It may not stay closed, it may pop open mid-cycle and let heat escape, or the dryer may refuse to start because it doesn't register the door as closed. Each kit includes 1 door catch and 1 strike, so you can replace the full latch set in one repair rather than guessing which half is worn. Because this latch design was used across several appliance families, the kit carries a long cross-reference list covering Whirlpool, Frigidaire, GE, LG, and Alliance-built part numbers; see the Replaces list below. Quick Answer The XPARTCO EXP570 Dryer Door Latch Kit fixes a dryer door that won't stay closed, opens mid-cycle, or an open-door condition that keeps the dryer from starting, caused by a worn or damaged catch and strike. Each kit includes 1 door catch and 1 strike. Fits Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis, and LG dryers. Classic symptom: the door swings open on its own, or you have to hold it shut to get the dryer to run. Common Problems This Part Fixes Dryer door won't stay closed Door pops open in the middle of a cycle Dryer won't start because the open-door condition isn't clearing Worn, cracked, or damaged catch or strike Heat escaping around the door, leaving clothes damp Door that no longer latches with a firm, positive click Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door latch kit directly replaces the following part numbers: 5366021400, 5303207102, AP2153772, PS475419, AP2137890, PS455020, LA-1003, LA1003, PS2162263, AP4242465, WE1M1011, WE1X1192, WE1M536, WE1X1195, WE01X1158, WE01X10023, WE01X10188, WE01X10184, AP5324728, PS3502777, AP2042206, PS266893, AP5324728, PS3502777, AP2042209, PS266896, AP2042175, PS266861, AP2042031, PS264343, AP3775568, PS959860, AP5238145, PS959856, WE1X1194, PS266895, AP2042208, WE1M1011, WE1X1192, WE1M536, WE1X1195, WE01X1158, WE01X10023, WE01X10188, WE01X10184, AP5324728, PS3502777, AP2042206, PS266893, AP5324728, PS3502777, AP2042209, PS266896, AP2042175, PS266861, AP2042031, PS264343, AP3775568, PS959860, AP5238145, PS959856, 4027EL2001A, 4026EL3001A, PS3522845, AP5238145, AP5242421, PS3522822, 00491624, AP3735937, PS959856, 5366021400, 5303207102, AP2153772, PS475419, AP2137890, PS455020, 279570. This latch kit was sold under the part numbers of several manufacturers: Whirlpool and Maytag (279570), Frigidaire and Electrolux (5303207102), GE (WE01X10023 and related), LG (4027EL2001A, 4026EL3001A), and Alliance-built dryers (LA-1003). The AP/PS-prefixed numbers are third-party catalog cross-references for the same physical parts. Compatibility This latch kit is used on dryer models from the following brands: Whirlpool, Kenmore (Whirlpool-built), Maytag, Amana, Roper, Estate, and Inglis dryers Frigidaire, Electrolux, and Kenmore (Frigidaire-built) dryers GE and Hotpoint dryers Select LG and Kenmore (LG-built) dryers Select Crosley, Norge, and Speed Queen dryers Note: This kit fits specific models within each brand, not every dryer a brand has made, and the latch design differs between manufacturers. Match the number on your old catch and strike, or on your dryer's parts diagram, against the Replaces list above rather than relying on brand alone. Contact our support team with your model number and we'll verify fit before you order. If only the catch needs replacing, see our single EXP571 Dryer Door Catch. Key Features Aftermarket replacement dryer door latch kit with 1 door catch and 1 strike Replaces both halves of the latch in one repair Restores a secure door closure so heat stays in and the dryer runs efficiently Resolves doors that won't stay shut, open mid-cycle, or trigger an open-door no-start Cross-references to Whirlpool, Frigidaire, GE, LG, and Alliance OEM numbering 1 kit per order Product Specifications Part Number EXP570 OEM Part Number 279570, 5303207102, WE01X10023, 4027EL2001A Part Type Dryer Door Latch Kit (Door Catch & Strike) Condition Aftermarket Replacement Kit Contents 1 Door Catch & 1 Strike Quantity 1 Kit Application Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis & LG Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Open the door and inspect the old catch on the cabinet and the strike on the door for cracks, wear, or loose mounting. Remove the old catch and strike, keeping track of how each one is oriented and mounted. Fit the new catch and strike in the same positions and fasten them securely. Close the door and confirm it latches with a firm click, stays shut, and lines up evenly with the cabinet. If the door still won't seat properly after the swap, check the door hinges and alignment, since a misaligned door can wear out new latch parts quickly. Frequently Asked Questions My dryer door won't stay shut — is this the part I need? Very likely. A worn or damaged catch or strike is a common reason a dryer door won't latch or pops open mid-cycle. Inspect both parts for cracks or wear. Because the two work as a pair, replacing both at once is the surest fix. My dryer won't start and seems to think the door is open. Could this be the cause? It can be. If the door isn't latching fully, the dryer may not register it as closed. If the latch looks fine and the door closes firmly but the dryer still won't start, the door switch may be the problem instead. What's included in the kit? Each kit includes 1 door catch and 1 strike. If you only need the catch, we also offer it separately as the EXP571 Dryer Door Catch. Will this fit my Whirlpool, Frigidaire, GE, or LG dryer? This kit is cross-referenced to part numbers from all of those brands, but it fits specific models rather than every dryer. Match the number on your old latch parts or parts diagram against the Replaces list, or contact our support team with your model number and we'll confirm before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM WPW10453947 Washer or Dryer Control Knob  The Genuine OEM WPW10453947 is a factory-original control knob used on both washers and dryers across the Whirlpool platform — the same knob design is shared between select top-load washer cycle-selector dials and dryer cycle/timer dials, depending on the model. It mounts onto the control shaft on the console and is what the user grips to select a wash or dry cycle. Over time these knobs commonly crack, the D-shaped shaft-grip inside wears out and starts spinning freely on the shaft, or the knob's pointer/indicator fades or breaks off. As the genuine Whirlpool part, it matches the factory shaft profile, detent feel, and indicator marking of the original equipment, so there's no fit or cosmetic mismatch. It directly replaces W10453947, 2304653, AP5607287, AWP50246, EAP3632979, PD00008425, PS3632979. Installs in under 5 minutes with no tools required — it's a simple push-on friction fit in most applications. Quick Answer The Genuine OEM WPW10453947 Washer or Dryer Control Knob fixes Whirlpool, Amana, Admiral, Inglis, Roper, Kenmore, Crosley, and Maytag washers and dryers with a cracked, spinning, or missing cycle-selector knob. This is the factory-original Whirlpool knob — not an aftermarket equivalent — and is used on both washer and dryer control panels depending on model. Replaces W10453947, 2304653, AP5607287, AWP50246, EAP3632979, PD00008425, PS3632979. Classic symptom: knob spins freely on the shaft without turning the dial, or won't stay in the selected cycle position. Common Problems This Part Fixes Control knob spins freely on the shaft without engaging the dial underneath Knob is cracked, chipped, or has broken retaining tabs on the back Knob won't stay pointed at the selected cycle Indicator marking or pointer on the knob is faded, worn, or broken off Knob is missing entirely, making it difficult to select a cycle Knob feels loose or wobbly on the control shaft Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This control knob directly replaces the following OEM and cross-reference part numbers: W10453947, 2304653, AP5607287, AWP50246, EAP3632979, PD00008425, PS3632979 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This control knob is compatible with select washer and dryer models from the following brands: Whirlpool washers and dryers (including WTW4616FW1, NTW4700YQ0, and related models) Amana washers and dryers (select models) Admiral washers and dryers (select models) Inglis washers and dryers (select models) Roper washers and dryers (select models) Kenmore washers and dryers (select Whirlpool-built models) Crosley washers and dryers (select models) Maytag washers and dryers (select Whirlpool-built models) Note: This same knob is used across hundreds of washer and dryer model numbers on both appliance types. Always verify fit using your appliance's exact model number before ordering, since visually similar knobs with a different shaft profile are used on other platforms. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM control knob — factory-original fit, feel, and appearance Used on both washer and dryer control panels across the Whirlpool platform Resolves "knob spins freely," "cracked knob," and "missing cycle indicator" symptoms Matches original detent feel and cycle-position indicator Push-on friction fit — no tools required for installation Replaces W10453947, 2304653, AP5607287, AWP50246, EAP3632979, PD00008425, PS3632979 Compatible with Whirlpool, Amana, Admiral, Inglis, Roper, Kenmore, Crosley, and Maytag washers and dryers Genuine OEM part — factory-specified materials and markings Product Specifications Part Number WPW10453947 OEM Part Number WPW10453947 Part Type Washer / Dryer Control Knob Condition Genuine OEM Replacement Application Washer or Dryer Cycle-Selector Control Panel Mounting Push-on friction fit to control shaft Compatible Brands Whirlpool, Amana, Admiral, Inglis, Roper, Kenmore, Crosley, Maytag Installation Notes ℹ️ No Tools Required — Unplug Appliance First Disconnect power to the washer or dryer before beginning. Note the current cycle position of the old knob before removing it, so you can align the new one the same way. Grip the old knob firmly and pull straight outward, away from the console, to release it from the friction fit on the shaft. If it's cracked and difficult to grip, work a flat-blade screwdriver gently behind the knob's edge to help pry it free, taking care not to damage the console. Line up the new WPW10453947 knob's D-shaped (or splined) center opening with the flat side of the control shaft, and press straight in until it seats fully against the console. Restore power and test that the knob turns smoothly through each cycle position and the indicator lines up correctly. Frequently Asked Questions Is this knob for a washer or a dryer? Both — this is a shared control knob design used on select Whirlpool-platform washers and dryers, depending on the model. The knob itself is identical; what it controls (wash cycle vs. dry cycle) depends on which appliance and console it's installed in. Confirm your appliance's model number before ordering to make sure this is the correct knob for your specific control panel. My knob spins freely and doesn't change the cycle — is this the fix? Yes, in most cases. This happens when the knob's internal shaft-grip (the D-shaped or splined opening that mates with the control shaft) wears out or cracks, so the knob spins independently of the shaft underneath it. Replacing the knob restores a snug grip on the shaft so turning it actually moves the selector. Do I need any tools to install this? No — it's a simple push-on friction fit. Pull the old knob straight off the shaft (a flat-blade screwdriver can help pry a stuck or cracked one loose) and press the new one on, matching the shaft's flat side to the knob's opening. No screws or fasteners are involved. Is this a genuine Whirlpool part or an aftermarket equivalent? This is the genuine, factory-original Whirlpool knob — not an aftermarket equivalent. It matches the original shaft profile, detent feel, and cycle-indicator markings, so there's no mismatch in fit or appearance versus the original equipment. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine Whirlpool OEM Part ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC47-00019A Dryer Heating Element Replaces WP35001247 The XPARTCO DC47-00019A is an aftermarket replacement universal-fit dryer heating element compatible with a wide range of electric dryers across multiple manufacturers — including Samsung, Whirlpool, Maytag, Amana, Inglis, and Kenmore. The heating element generates the heat that warms the air circulating through the dryer drum, evaporating moisture from wet clothes during each drying cycle. When the element fails, the dryer continues to tumble normally but produces no heat, leaving clothes damp at the end of a complete cycle. This replacement element comes pre-assembled with insulators and restring already attached, allowing for fast installation. Rated 240V, 5300W, with metal and ceramic construction. Overall dimensions are approximately 17"L x 6-1/2"W x 2-1/2"H. Important: this is a heating element assembly only — you must reuse the housing/cannister from your old element when installing the new one. It directly replaces DC47-00019A, 35001247, WP35001247, WP35001247VP, TJDC47-00019A, DE0019A, ERDC47-00019A, 35001119, 2068550, 1185561, AP4045884, AP4201899, AP6008695, AH2038533, EA2038533, EAP2038533, EAP11741835, PD00001991, PD00002996, PS2038533, PS4205218, and PS11741835. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO DC47-00019A Dryer Heating Element fixes Samsung, Whirlpool, Maytag, Amana, Inglis, and Kenmore electric dryers that tumble normally but produce no heat or take much longer than usual to dry. Universal-fit element — 240V, 5300W. 17"L x 6-1/2"W x 2-1/2"H. Insulators and restring pre-attached. Must reuse the housing/cannister from the old element. Replaces DC47-00019A, 35001247, WP35001247, WP35001247VP, TJDC47-00019A, DE0019A, ERDC47-00019A, 35001119, 2068550, 1185561, AP4045884, AP4201899, AP6008695, PS2038533, PS4205218, PS11741835. Common Problems This Part Fixes Dryer tumbles normally but produces no heat — element coil burned through Dryer takes significantly longer than usual to dry a load Clothes coming out damp or only partially dried at the end of a cycle Visible breakage in the element coil — snapped or burned-through Ni-Cr wire Dryer trips the circuit breaker when the heat setting is selected — shorted element Burning smell during operation — element arcing at a weak point in the coil Multimeter continuity test on the element shows an open circuit Replaces Part Numbers This dryer heating element directly replaces the following OEM and cross-reference part numbers across multiple brands: DC47-00019A, 2068550, AP4201899, ASM33630, AP2038533, DE0019A, ERDC47-00019A, PD00001991, PS4205218, TJDC47-00019A, WP35001247, 35001247, 1185561, AP6008695, AWP47390, EAP11741835, PD00002996, PS11741835, WP35001247VP. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This universal-fit heating element is compatible with select electric dryers from multiple manufacturers: Samsung electric dryers — DV2, DV3, DV4, DV5, DVE series (DV40J3000EW, DV42H5000EW, DV42H5200EW, DV42H5600EP, DV45H7000EW, DV48H7400EW, DV50F9A7EVW, DV50F9A7EVP, DVE50M7450W, DVE50R5200W, DVE50R5400V, DV203AEW, DV206LEW, DV209AEW, DV210AEW, DV419AEU, DV448AEE, DV448AEP, DV5471AEW and many related models) Whirlpool electric dryers (select models — see WP35001247 cross-reference) Maytag electric dryers (MDE6700AYW, MDE6700AZW, MDG6700AWM, MDG6700AWW and related) Amana electric dryers (NED7200TW10, YIED7200TW10 and related) Inglis electric dryers (select models) Kenmore / Sears electric dryers (Samsung and Whirlpool-built — select models) Important — Reuse Existing Housing: This listing is for the heating element assembly only — the metal housing/cannister that the element sits inside is not included. You must reuse the housing from your old element. Remove the old element from its housing, then install the new DC47-00019A element into that same housing before reinstalling in the dryer. Also: this part is for electric dryers only — gas dryer models use different components. Always verify your specific model number before ordering. Key Features Universal-fit replacement heating element for multiple dryer manufacturers — replaces both Samsung DC47-00019A and Whirlpool/Maytag WP35001247 part numbers Generates the heat that warms drying air — essential for the dryer to actually dry clothes Pre-strung Ni-Cr (nickel-chromium) heating wire — high heat conductivity and resistance to warping over time Insulators and restring already attached — ready for installation into the existing housing Rated 240V, 5300W — correct electrical specifications for compatible electric dryers Dimensions: 17"L x 6-1/2"W x 2-1/2"H Metal and ceramic construction — durable for repeated heat/cool cycles Electric dryers only — NOT compatible with gas dryer models Important: heating element assembly only — must reuse the housing/cannister from the old element Replaces 22+ OEM and cross-reference part numbers across Samsung, Whirlpool, Maytag, Amana, and related brands Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number XPDC47-00019A Also Replaces (Whirlpool-side) WP35001247, 35001247 Part Type Dryer Heating Element Assembly (Universal Fit) Condition Aftermarket Replacement Application Electric Dryers Only (NOT gas) Voltage 240V AC Wattage 5300W Terminal Connections 2 spade terminals Dimensions 17"L x 6-1/2"W x 2-1/2"H Material Metal / Ceramic / Ni-Cr coil wire Includes Heating element assembly with insulators and restring pre-attached (housing NOT included — reuse old) Compatible Brands Samsung, Whirlpool, Maytag, Amana, Inglis, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Do Not Touch the Element with Bare Hands Disconnect power before beginning. Wear work gloves throughout — there are sharp sheet metal edges inside the dryer cabinet. The new heating element coil is sensitive to skin oils, which can cause premature burnout — handle the element only by the metal frame, not the coil wire. Remove the rear panel of the dryer to access the heating element housing/cannister. Take a photo of all wire connections and the orientation of the element before disconnecting anything. Disconnect the wires from the old element terminals and remove the housing from the dryer. With the housing on a workbench, remove the old element from inside the housing — note exactly how it sits and how the restring is positioned. Install the new DC47-00019A element into the same housing, following the same orientation as the old element. Do not let the Ni-Cr heating wire touch the housing during installation — this can cause arcing and immediate burnout. Reinstall the housing in the dryer, reconnect all wires snugly to the correct terminals, and reinstall the rear panel. Restore power and run a test heat cycle to confirm the dryer is heating properly. While the rear panel is open, inspect the high-limit thermostat, thermal fuse, and thermistor — if the element failed due to overheating, these may also be stressed. Tools needed: Phillips screwdriver, 1/4" nut driver, work gloves. Frequently Asked Questions Does this really fit both Samsung AND Whirlpool dryers? Yes — this is one of the more unusual cases in dryer parts where an aftermarket heating element has been designed to serve as a direct replacement for both the Samsung DC47-00019A and the Whirlpool/Maytag WP35001247 (35001247) elements. The two OEM elements share the same physical dimensions, electrical specifications (240V, 5300W), and terminal configuration, allowing a single aftermarket element to function correctly in both platforms. Compatible models span Samsung's DV series, Whirlpool/Maytag's affected dryers (MDE6700/MDG6700 and similar), and select Amana, Inglis, and Kenmore Whirlpool-built or Samsung-built models. Always verify your specific model number before ordering. Why do I need to reuse the housing from the old element? This listing is for the heating element assembly only — the metal cannister or housing that contains the element is not included. The housing is a heavy gauge metal enclosure with mounting brackets that secure it to the dryer cabinet, along with airflow ducting that directs air across the heating coil. Reusing the housing keeps the cost down and is standard practice for this type of replacement. Carefully remove the old element from the housing, install the new element in its place, and then reinstall the housing in the dryer. If your housing is damaged or burned through, it will need to be replaced separately. How do I know if the heating element has failed? The clearest sign is a dryer that tumbles and runs through a complete cycle normally but produces little or no heat, leaving clothes damp at the end. You may also notice the dryer taking much longer than usual to dry a load as it tries to compensate. Visually inspecting the element after removing the rear panel can reveal burn marks, breaks in the coil, or visible arcing damage. A multimeter continuity test on the disconnected element will also confirm failure — a working element shows continuity, while a failed element reads an open circuit (no continuity). Should I replace the thermal fuse and thermostats at the same time? It's a good idea to inspect them. When a heating element fails — especially if it failed due to overheating rather than simple end-of-life wear — the paired thermal fuse, high-limit thermostat, and thermistor located in the same area can also be stressed by the heat event. Since the rear panel must already be open to replace the element, checking these components' continuity with a multimeter is a quick step that can prevent a repeat repair if any of them are also on the verge of failing. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung or Whirlpool OEM part, but is manufactured to match the electrical specifications (240V, 5300W), dimensions, and Ni-Cr coil construction of the original DC47-00019A and WP35001247 heating elements that it replaces. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH01X24378 Washer / Dryer Cycle Selector Knob The XPARTCO WH01X24378 is an aftermarket replacement cycle selector knob (options knob) compatible with a wide range of GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers. The selector knob is one of the primary user controls on the appliance's control panel — it's what you grip and turn to choose the wash or dry options and settings for each load. On many GE-platform washers and dryers, this smaller selector knob works alongside a larger main timer/cycle knob to give you fine-grained control over the specific options within your selected cycle. Over time, selector knobs wear out from repeated twisting motions, get cracked or dropped, or lose their grip on the internal shaft — all of which make it difficult or impossible to change the appliance's settings. Constructed from heat-resistant plastic with a clean white and chrome finish. Snap-on installation — no tools required. Pulls straight off the control shaft and pushes back on. This knob directly replaces WH01X24378, AP5986397, 4396548, and PS11726904. Important: this is the smaller cycle selector/options knob. If you need the larger main timer knob for your GE washer, that's a different part number (PS11736611) — check which knob is broken before ordering. Installs in under 1 minute — no tools required. Quick Answer The XPARTCO WH01X24378 Washer Cycle Selector Knob replaces a cracked, loose, stripped, or missing selector knob on GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers. Heat-resistant plastic, white and chrome finish. Snap-on installation — pulls straight off, pushes back on. Replaces AP5986397, 4396548, PS11726904. This is the smaller cycle/options knob — NOT the larger main timer knob (PS11736611). No tools required. Common Problems This Part Fixes Selector knob cracked, broken, or split from age and repeated use Knob loose and slipping on the control shaft — no longer changes settings when turned Knob has stripped or damaged internal grip and won't stay coupled to the shaft Knob missing entirely from the control panel Knob damaged from impact — dropped or bumped Knob discolored, faded, or worn from years of daily handling Difficulty selecting cycle options — knob no longer clicks into detent positions cleanly Water or detergent damage to the knob material Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This cycle selector knob directly replaces the following OEM and cross-reference part numbers: WH01X24378, 4396548, AGE26094, AP5986397, EAP11726904, OEM17959200, PD00037085, PS11726904. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This selector knob is compatible with select washers and dryers from the following brands: GE washers — GTW500ASNWS and related top-load models GE dryers — GTX42GASJWW, GTD45GASJ2WS and related models GE Profile and GE Café washers and dryers (select models) GE Monogram washers and dryers (select models) Hotpoint washers and dryers (select models) RCA washers and dryers (select GE-built models) Haier washers and dryers (select models using GE-platform controls) Important — Two Knobs, Two Part Numbers: Many GE washers and dryers have TWO knobs on the control panel: a larger main timer/cycle knob and a smaller cycle selector/options knob. The WH01X24378 is the smaller cycle selector/options knob. If your broken knob is the larger main timer knob, you need a different part number (PS11736611 on many GE models). Before ordering, visually confirm which knob is broken and compare the size and shape to the images. Contact our support team with your model number if you're unsure. Key Features Cycle selector/options knob — used to choose specific settings within your selected wash or dry cycle Snap-on installation — pulls straight off the control shaft, pushes straight back on; no tools or hardware required Heat-resistant plastic construction — designed for years of daily use without warping or cracking Clean white and chrome finish complements GE appliance styling Ergonomic shape for comfortable grip and precise cycle selection Restores full cycle control when the original knob has cracked, stripped, or gone missing Replaces WH01X24378, AP5986397, 4396548, and PS11726904 Compatible with GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers Important: this is the smaller cycle selector/options knob — NOT the larger main timer knob (PS11736611, sold separately) Aftermarket replacement built to OEM-equivalent quality standards Quick replacement — installs in under 1 minute Product Specifications Part Number XPWH01X24378 Part Type Washer/Dryer Cycle Selector Knob (Options Knob) Condition Aftermarket Replacement Application Washers and Dryers (GE platform) Knob Size Smaller cycle/options knob (NOT the larger main timer knob) Color White / Chrome Material Heat-resistant plastic Installation Snap-on — no tools required Larger Timer Knob Different part — PS11736611 (sold separately) Compatible Brands GE, Hotpoint, RCA, Haier, Monogram, Café Installation Notes ⚠️ Unplug Washer/Dryer Before Starting — Quick Toolless Replacement Disconnect power before beginning as a general safety precaution. Wear work gloves if desired. Locate the old cycle selector knob on the control panel of your washer or dryer. Grip the knob firmly and pull it straight off the control shaft — it should come off with a moderate pull (no tools or hardware required). If the knob is stuck or the internal grip has stripped and it's spinning without releasing, use a soft cloth wrapped around it for better grip, or gently pry it off with a plastic tool (avoid metal tools that could damage the control panel finish). Once the old knob is off, inspect the metal or plastic control shaft — if it's damaged, worn round, or spinning freely with no resistance, the underlying switch or shaft may also need replacement. If the shaft is intact, align the new WH01X24378 knob with the flat sides of the shaft (the knob has a matching D-shape or flat receiver inside) and push it firmly into place until it seats fully. Rotate the knob through its full range of positions to confirm it clicks into detents cleanly and turns smoothly. Restore power and run a test cycle. Tools needed: None (soft cloth optional). Frequently Asked Questions Is this the smaller or larger knob on my GE washer? The WH01X24378 is the smaller cycle selector (options) knob. Many GE washers and dryers have two knobs on the control panel: a larger main timer/cycle knob that selects the primary wash program, and a smaller cycle options knob (this one) that selects sub-options like temperature, spin speed, or soil level. Before ordering, look at your control panel and identify which knob has failed — if the smaller knob is broken, this is the correct part. If the larger main timer knob is broken, you need a different part (PS11736611 on many GE models). The two knobs are not interchangeable. How do I remove the old knob if it's cracked or spinning without coming off? If the internal grip on the old knob has stripped and it's spinning freely on the shaft without releasing, wrap a soft cloth around it for extra grip and pull firmly straight up. If that still doesn't work, gently pry it off with a plastic pry tool (a plastic putty knife or credit card can work). Avoid metal tools that could scratch the control panel finish. If the knob is cracked, you can sometimes break away the broken pieces to expose the internal grip on the shaft, then work each piece off. Once the old knob is off, inspect the control shaft — if it's damaged or spinning without resistance, the underlying switch may need replacement too. Do I really not need any tools for this? Correct — the WH01X24378 uses a snap-on installation with no screws or hardware. To install, align the new knob with the flat side (D-shape) of the control shaft and push it straight down until it seats fully. The whole replacement typically takes under a minute. Just make sure the knob is fully seated and rotates through all positions with the correct detent clicks before you plug the appliance back in. The knob installs fine but my washer still doesn't change settings — what next? If the new knob is installed correctly (fully seated and rotates through positions with detent clicks) but changing the knob position doesn't change the cycle behavior, the underlying selector switch or control shaft has likely failed — not the knob. Common causes include the shaft spinning freely without engaging the switch inside (the shaft has stripped or broken), or the electrical selector switch itself has failed. In these cases, replacing just the knob won't fix the problem — the switch assembly behind the panel also needs to be replaced. Contact our support team with your model number for the correct switch part number. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from heat-resistant plastic to match the dimensions, D-shape shaft receiver, snap-on installation, and cycle selection function of the original WH01X24378 selector knob used in compatible GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM WE4M137 Dryer High Limit Thermostat The WE4M137 is a genuine OEM high limit thermostat for GE, Hotpoint, and Kenmore dryers. Mounted on the upper right side of the heater housing, this safety thermostat monitors the temperature of the heating circuit and cuts power to the heating element (and in some conditions the motor) if the dryer runs hotter than it should — typically from restricted airflow, a clogged vent, or a failing cycling thermostat. Unlike a one-time thermal fuse, this is an auto-resetting high limit thermostat (rated L315-65F): it opens at approximately 315°F to stop overheating, then automatically closes again once the unit cools down, without needing to be replaced after each trip. This is a genuine OEM part manufactured to the original factory temperature rating and mounting — not an aftermarket equivalent — so trip point and reset behavior match what came on the dryer originally. If this component trips repeatedly, it's worth checking the underlying cause of the overheating at the same time — a clogged lint trap or restricted exhaust vent is the most common root cause. Quick Answer The Genuine OEM WE4M137 High Limit Thermostat fixes a GE, Hotpoint, or Kenmore dryer that shuts off a few minutes into a heat cycle, stops early and won't restart until it cools down, or cycles on and off intermittently. Genuine OEM, factory temperature rating, auto-resetting, rated to open at approximately 315°F. Classic symptom: dryer runs fine for a few minutes then quits on heat, and won't restart again until it's had time to cool. Common Problems This Part Fixes Dryer shuts off a few minutes into a heat-dry cycle Dryer stops early and won't restart until it cools down Intermittent shutdowns during the drying cycle Clothes coming out damp because the cycle keeps cutting short Dryer won't start at all if the thermostat has failed in an open position Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This thermostat directly replaces the following part numbers: WE4M137 replaces WE4M457, 276438, WE04M0137, WE04X25197, 559C131G04, AGE25626, AH267900, AP2042565, EAP267900, EA267900, PD00001228, PS267900 These numbers span several generations of GE's own part numbering for this thermostat as model lines and sub-assemblies were updated — all are the correct genuine replacement for this component regardless of which number appears on your dryer's parts diagram. Compatibility This thermostat is compatible with 28+ GE, Hotpoint, and Kenmore dryer models, including: Kenmore 2661532110, GE 2661532210 Numerous additional GE, Hotpoint, and Kenmore dryer and washer-dryer combo models DBXR463ED1WW, DBXR463ED2WW, DBXR463EG7WW, DHDVH52EF0WW, DHDVH66EH0BB, DPSR610EG0WT, DPSR610EG1WT, DPSR610EG2WT, DPSR610EG3WT, DPSR610EG4WT, DPSR610EG5WT, DPSR610EG6WT, DPSR610EG7WT, DPSR610EG8WT, GFDN245EL1MS, GFDS350GL0WW, GFDS350GL1WW, GFDS355EL0MV, GLDP280ED0WS, GLDP280GD0WS, GTDN500EM0WS, GTDN500EM1WS, GTDN500EM2WS, GTDX180ED0WW, GTDX180ED1WW, GTDX180ED3WW, GTDX180ED4WW, GTDX180ED5WW, GTDX180ED6WW, GTDP180ED0WW, GTDP180ED1WW, GTDP200EF1WS, GTDP220EF1WW, GTDP301EL1WS, GTDP490ED0WS, HTDP120ED0WW, HTDX100ED0WW, NBXR333EG1WW, NWXR483EG8WW Note: This thermostat has also been referenced for some Fisher & Paykel dryer applications in sourcing, though we were not able to confirm a specific Fisher & Paykel model list. Confirm your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM high limit thermostat — factory fit and trip-point accuracy, not an aftermarket equivalent Auto-resetting design — no need to replace after each trip, unlike a one-time thermal fuse Rated to open at approximately 315°F to prevent overheating damage Resolves early-shutoff, won't-restart-until-cool, and intermittent cycling symptoms Fits 28+ GE, Hotpoint, and Kenmore dryer and washer-dryer combo models Straightforward swap — typically 15–30 minutes with basic hand tools Product Specifications Part Number WE4M137 OEM Part Number WE4M137 Part Type Dryer High Limit Thermostat (Auto-Reset) Condition Genuine OEM Temperature Rating L315-65F (Opens ~315°F, Auto-Resets on Cooling) Location Upper Right Side of Heater Housing Application GE, Hotpoint & Kenmore Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Remove the dryer's rear or front panel per your model's service guide to access the heater housing — the thermostat is mounted on its upper right side. Disconnect the wire terminals from the old thermostat, noting their positions, and remove the mounting screw holding it in place. Install the new thermostat in the same position and reconnect the wire terminals. Before closing the dryer back up, clean out the lint trap and check the exhaust vent for restrictions — a clogged vent is the most common cause of this thermostat tripping repeatedly, and clearing it now can prevent a repeat failure. Frequently Asked Questions My dryer shuts off a few minutes into the cycle and won't restart — is this the part I need? Yes, this is a classic symptom of a failing high limit thermostat. It's designed to cut power when the dryer overheats and automatically reset once things cool down, so if your dryer won't restart until it's had time to sit, this thermostat is a likely cause. Is this a one-time fuse like the thermal fuse, or does it reset itself? This is an auto-resetting thermostat, not a one-time thermal fuse. It opens to cut power when the dryer overheats, then closes again automatically once the unit cools — it doesn't need to be replaced every time it trips. If yours has failed and won't reset or close again, that's when replacement is needed. Why does my dryer keep tripping this thermostat? Repeated tripping is usually caused by restricted airflow — a clogged lint trap, a crushed or blocked exhaust duct, or a bird's nest or lint buildup in the outside vent hood — or a failed cycling thermostat elsewhere in the heating circuit. Clear the airflow path when you replace this thermostat, or the new one may trip again. Is this a genuine GE part or an aftermarket copy? This is a genuine OEM thermostat manufactured to the original factory specification — not an aftermarket equivalent — so trip temperature and reset behavior match what came on the dryer originally. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 279816 Dryer Thermostat Kit The XPARTCO 279816 is an aftermarket replacement thermal fuse and high-limit thermostat combo kit for Whirlpool-built dryers. These are the dryer's two thermal safety devices, and they're bundled together in this kit because they tend to fail around the same time and share a common cause: restricted airflow that lets heat build up beyond safe levels. The high-limit thermostat is the first line of defense, opening at approximately 250°F (L250-80F) to interrupt heating if the dryer runs too hot. If that isn't enough to bring the temperature back down, the thermal fuse is the final failsafe, opening permanently at approximately 309°F to cut power to the dryer entirely. That's an important distinction between the two parts: the high-limit thermostat is a cycling safety device that can open and close as temperature rises and falls, while the thermal fuse is a one-time device — once it blows, it's done, and the dryer won't run again until it's replaced. This kit includes both components plus mounting screws and a wiring set with a jumper wire and extra terminals, which is used specifically when replacing an older-style thermostat that had a wire pressing directly onto the heating element. A dryer that won't start at all, with no lights or response, usually means the thermal fuse has blown; a dryer that runs but won't heat, or that stops heating partway through a cycle, points more toward the thermostat. It directly replaces 2651, 279816VP, 3399848, 3977393, 3390291, AP3094244, AH334299, EA334299, EAP334299, PD00002348, and PS334299. Quick Answer The XPARTCO 279816 Dryer Thermostat Kit fixes Whirlpool-built dryers that won't start at all, won't heat, or stop heating partway through a cycle. Includes a thermal fuse (opens ~309°F), a high-limit thermostat (opens ~250°F), mounting screws, and a wiring set. Replaces 2651, 279816VP, 3399848, 3977393, 3390291, AP3094244, AH334299, EA334299, EAP334299, PD00002348, PS334299. Always inspect and clean the dryer venting when replacing this kit — a blown fuse or tripped thermostat is a symptom of restricted airflow, and skipping this step means the new parts are likely to fail again. Common Problems This Part Fixes Dryer won't start at all — no lights, no tumble, no response to any button Dryer runs and tumbles but produces no heat Dryer heats for a while, then stops heating partway through a cycle Dryer that stopped working suddenly, especially after running unusually hot Clothes coming out extremely hot right before the dryer stopped heating or stopped entirely Repeated blown fuses or tripped thermostats on a dryer with a known venting restriction Continuity test shows an open circuit across the old fuse or thermostat Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermostat kit directly replaces the following OEM and cross-reference part numbers: 279816, 279816VP, 3399848, 3977393, PD00002348, AWP39198, EAP334299, AH334299, EA334299, AP3094244, PS334299. 3977393 is the thermal fuse component and 3390291 is the "new-style" high-limit thermostat component included in this kit. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat kit is compatible with select Whirlpool-built dryers across the Whirlpool family of brands, including: Whirlpool electric and gas dryers — WED series Maytag electric and gas dryers — NED series (select Whirlpool-built models) Admiral, Amana, Crosley, Estate, Inglis, Magic Chef, and Roper dryers (select models) Kenmore and KitchenAid dryers (select Whirlpool-built models) Verified model numbers include: WED6200SW1, NED4600YQ0, NED4600YQ1, NED4655EW1, and LER3624EQ. Note: The wiring set included in this kit is designed for replacing an older-style thermostat that used a wire pressed directly onto the heating element. If your dryer uses the true old-style push-on thermostat and fuse combination (part 3977767), you'll need a different kit (commonly listed as APN197) instead of this one. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which kit fits your dryer. Key Features Complete combo kit — thermal fuse, high-limit thermostat, mounting screws, and wiring set in one package Thermal fuse opens at approximately 309°F as a one-time, non-resettable safety cutoff High-limit thermostat opens at approximately 250°F (L250-80F) as a cycling safety device Resolves "won't start at all," "runs but doesn't heat," and "stops heating mid-cycle" symptoms Wiring set includes jumper wire and extra terminals for older-style push-on thermostat connections Replaces 2651, 279816VP, 3399848, 3977393, 3390291, AP3094244, AH334299, EA334299, EAP334299, PD00002348, and PS334299 Compatible with Whirlpool, Maytag, Admiral, Amana, Crosley, Estate, Inglis, Magic Chef, Roper, Kenmore, and KitchenAid dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 279816 OEM Part Number 279816 Part Type Dryer Thermal Fuse & High-Limit Thermostat Kit Condition Aftermarket Replacement Kit Contents Thermal fuse, high-limit thermostat, mounting screws, wiring set Thermal Fuse Opening Temp Approx. 309°F (one-time, non-resettable) High-Limit Thermostat Opening Temp Approx. 250°F / L250-80F (cycling) Wiring Set Jumper wire + extra terminals for older-style push-on thermostats Quantity 1 kit Compatible Brands Whirlpool, Maytag, Admiral, Amana, Crosley, Estate, Inglis, Magic Chef, Roper, Kenmore, KitchenAid Installation Notes ⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel: remove the screws securing the panel to reach the blower housing area where both the thermal fuse and high-limit thermostat are mounted, usually close together near the heating element or blower assembly. Photograph the wiring before disconnecting anything, and note whether your old thermostat used a push-on wire connection at the heating element — if so, use the included jumper wire and extra terminals to make the new connection correctly. Remove the mounting screws holding each old component in place and disconnect their wire terminals. Before installing the new parts, test the old fuse and thermostat with a multimeter to confirm which one (or both) is actually open, rather than assuming. This is the most important step: fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. A blown fuse or tripped thermostat is a symptom of restricted airflow, and skipping this step means the new parts are likely to fail again. Install the new thermal fuse and thermostat from this kit in the same mounting positions, reconnect the wire terminals (using the included wiring set if applicable), and secure the mounting screws. Reinstall the rear panel, restore power, and run a test cycle to confirm normal heating and shutoff behavior. Tools needed: Phillips or nut driver (model-dependent), multimeter, vent brush or vacuum attachment for cleaning ductwork, work gloves. Frequently Asked Questions Why does this kit include two different parts instead of just one? The thermal fuse and high-limit thermostat work together as a two-stage safety system, and they're bundled because they commonly fail together — both are reacting to the same underlying overheating condition, usually restricted airflow. The high-limit thermostat trips first at a lower temperature and can cycle open and closed; if that's not enough to control the heat, the thermal fuse trips at a higher temperature and shuts the dryer down permanently until replaced. Replacing both together addresses the full safety chain rather than just one link in it. My dryer won't start at all versus my dryer runs but doesn't heat — which part is which? A dryer with absolutely no response — no lights, no tumbling, nothing — usually points to the thermal fuse, since it's wired to cut power more broadly when it blows. A dryer that tumbles and runs normally but produces no heat, or that starts heating and then stops partway through, points more toward the high-limit thermostat. Testing both components with a multimeter will confirm exactly which one has failed. I replaced both parts and the dryer failed again. What's going on? This is a strong sign that the underlying cause — almost always restricted airflow — was never addressed. Neither of these parts fails from age; they trip or blow because the dryer overheated. If new parts fail again, thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. If airflow checks out and the parts still fail, have the heating element checked as well, since a shorted element can also drive excess heat. Do I need the wiring set included in this kit? Only if your dryer's original thermostat used a wire that pressed directly onto the heating element (an older-style connection) rather than a standard push-on terminal. If your dryer already uses a straightforward terminal connection, you can skip the jumper wire and extra terminals and connect the new thermostat directly. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the opening temperatures, terminal configuration, and mounting positions of the original 279816 thermal fuse and high-limit thermostat kit used in compatible Whirlpool, Maytag, and related dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO XP311 Dryer Thermostat Kit for LG The XPARTCO XP311 is an aftermarket replacement 3-piece thermostat kit for LG electric dryers, bundling the thermal fuse, thermistor, and high-limit thermostat that work together to regulate and protect the dryer's heating system. These three components monitor heat continuously during normal operation and step in at different thresholds if something goes wrong, which is why they're commonly replaced as a set — a single overheating event or a slow age-related drift in one part can put stress on the others, and buying them together also saves a second teardown if one of the remaining parts fails soon after. This kit includes: the 6931EL3003D thermal fuse, a one-time safety device that permanently cuts power to the dryer if internal temperatures climb dangerously high; the 6323EL2001B thermistor, a temperature sensor assembly with wire harness that continuously reports drum temperature to the control board so it can regulate heat output during the cycle; and the 6931EL3001E high-limit thermostat, which automatically shuts off the heating element if the dryer's temperature exceeds safe operating limits, without needing to be replaced like the thermal fuse does. Symptoms of failure in this circuit include incomplete drying, insufficient heating time, overheating that damages clothing, and the dryer shutting down prematurely or failing to start at all. It directly replaces AP4440975, 1268366, 6931EL3003E, AH3530485, EA3530485, PS3530485 (thermal fuse); AP4441539, 1268206, 6323EL2001H, AH3529026, EA3529026, PS3529026 (thermistor); and AP4440977, 1268363, 6931EL3001B, 6931EL3001C, AH3530481, EA3530481, PS3530481, 6931EL3001F (high-limit thermostat). Quick Answer The XPARTCO XP311 Dryer Thermostat Kit fixes LG (and select Kenmore) electric dryers with incomplete drying, insufficient heat, overheating that damages clothes, or a dryer that shuts down prematurely or won't start. 3-piece kit: thermal fuse (6931EL3003D), thermistor (6323EL2001B), and high-limit thermostat (6931EL3001E). Replaces 6323EL2001B, 6931EL3001E, 6931EL3003D, and their full cross-reference sets listed below. These three parts share the same circuit and commonly fail together — replacing all three at once is standard practice when one has failed. What's In The Kit Component Part Number Function Thermal Fuse 6931EL3003D One-time safety device — permanently cuts power if the dryer overheats. Cannot be reset once blown. Thermistor 6323EL2001B Continuously senses drum temperature and reports it to the control board to regulate heat output. High-Limit Thermostat 6931EL3001E Automatically shuts off the heating element if temperature exceeds safe limits. Resets automatically, unlike the thermal fuse. Common Problems This Kit Fixes Dryer runs but clothes come out only partially dry Insufficient heating time or reduced heat output Overheating that scorches or damages clothing Dryer shuts down prematurely mid-cycle Dryer won't start at all Inconsistent drying results from cycle to cycle Dryer that recently blew a thermal fuse and needs the related components checked Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermostat kit directly replaces the following OEM and cross-reference part numbers: 6931EL3003D, 1268366, AH3530485, EA3530485, PD00001818, EAP3530485, AP4440975, PS3530485, 6323EL2001B, 1268206, 6323EL2001H, AH3529026, PD00001821, EAP3529026, EA3529026, AP4441539, PS3529026, 6931EL3001E, 1268363, 6931EL3001C, PD00023869, EAP3530481, AH3530481, EA3530481, AP4440977, PS3530481. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This kit is compatible with select LG electric dryers, and also fits select Kenmore dryers built on the LG platform, including model numbers such as: CDE3379WN DLE0332W, DLE0442G, DLE0442W, DLE0442W01 DLE1310W, DLE2101W, DLE2140W, DLE2240W DLE2512W, DLE2514W, DLE2515S, DLE2516W, DLE2522W, DLE2524W, DLE2532W DLE3733D, DLE3733S, DLE5955W Note: This kit is for LG electric dryers. Different resistance values, dimensions, and mounting methods apply across brands and models, so always verify your full model number before ordering rather than relying on physical resemblance alone. Contact our support team with your model number if you're unsure. Key Features Complete 3-piece kit — thermal fuse, thermistor, and high-limit thermostat in one purchase Addresses the full temperature-regulation and safety circuit at once, rather than piecemeal Resolves "incomplete drying," "insufficient heat," "overheating," and "premature shutdown" symptoms Thermistor ships with its wire harness included No special tools required for installation Direct drop-in replacement for all three original components Replaces the full cross-reference set for 6931EL3003D, 6323EL2001B, and 6931EL3001E listed above Compatible with LG and select Kenmore electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Kit Part Number XP311 Kit Contents 1x Thermal Fuse (6931EL3003D), 1x Thermistor (6323EL2001B), 1x High-Limit Thermostat (6931EL3001E) Condition Aftermarket Replacement Application LG Electric Dryers Thermal Fuse Type One-time use, non-resettable High-Limit Thermostat Type Automatically resetting Thermistor Includes wire harness Repair Difficulty Easy to Moderate — no special tools required Compatible Brands LG, select Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Test Before Assuming All Three Have Failed Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel or the front, depending on your model — these components are commonly mounted on or near the blower housing and heater duct assembly. Photograph the wiring connections before disconnecting anything, since the thermal fuse, thermistor, and high-limit thermostat can look similar and are easy to swap positions by mistake. Before installing the full kit, it's reasonable to test each old component with a multimeter to confirm which have actually failed — the thermal fuse and high-limit thermostat can each be checked for continuity, though replacing all three together is still standard practice given how this circuit tends to fail. Remove each old component from its mounting position, noting orientation, and disconnect its wiring. Install each new component from the kit in the same position and orientation as the part it replaces, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal heating, consistent drying, and no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), multimeter (recommended), work gloves. Frequently Asked Questions Do I really need to replace all three parts, or can I just replace the one that failed? You can test each component individually with a multimeter and replace only the ones that fail, but there's a good reason these are commonly sold and replaced together: they share the same heating circuit and tend to age or fail around the same time, especially if an overheating event caused the original failure. Replacing all three at once avoids a second teardown if one of the remaining original parts fails again soon after. What's the difference between the thermal fuse and the high-limit thermostat? They sound similar. Both protect against overheating, but they behave very differently. The high-limit thermostat is the first line of defense — it shuts off the heating element automatically if temperature climbs too high, then resets itself once things cool down, letting the dryer resume normal operation. The thermal fuse is the backup: if temperatures climb high enough that the thermostat alone doesn't prevent a dangerous overheat, the fuse permanently opens the circuit and cuts all power. Unlike the thermostat, the fuse cannot reset itself and must be physically replaced once it blows. What does the thermistor actually do, and why does it matter if it's a sensor rather than a switch? The thermistor doesn't switch anything on or off directly — it's a variable resistor whose resistance changes with temperature, and the control board reads that resistance continuously to know exactly how hot the drum is running. That ongoing feedback is what lets the control board fine-tune heat output throughout the cycle rather than just running hot or cold. A failing thermistor can cause the control to misjudge temperature, leading to insufficient heat, inconsistent drying, or the control cutting the cycle short. My dryer blew a thermal fuse. Should I get this whole kit instead of just the fuse? It's worth considering, especially since a blown thermal fuse usually means the dryer actually overheated at some point — and that same overheating event can stress the thermistor and high-limit thermostat even if they haven't failed outright yet. Also worth checking regardless of which parts you replace: restricted exhaust venting is the most common root cause of dryer overheating, so inspect and clean the vent ducting when you do this repair, or the new parts may face the same stress that damaged the originals. Is this an OEM or aftermarket kit? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine LG OEM kit, but each component is manufactured to match the electrical specifications, resistance values, and mounting configuration of the original 6931EL3003D thermal fuse, 6323EL2001B thermistor, and 6931EL3001E high-limit thermostat used in compatible LG electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WPW10420741 Genuine OEM Dryer Push To Start Switch - Compatible with Whirlpool, Kenmore, Maytag Product Description Restore your dryer’s functionality with the WPW10420741 Genuine OEM Dryer Push To Start Switch. This Whirlpool-manufactured switch, featuring screw terminals, is designed as a replacement for select Whirlpool, Kenmore, Maytag, and other compatible dryers. It initiates the drying cycle with a simple button press, addressing issues like the dryer not starting or starting inconsistently. Built for durability, it ensures reliable performance under frequent use. Note: Includes (1) push to start switch. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: WPW10420741, W10420741, PD00008413, EAP3632880, AP6021228, PS11754549. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: WET4027HW0, WET4027HW1, WET4027HW2, YWET4027HW0, 7MWGT4027HW0 Kenmore: 110.97591420, 110.97591220, 110.97592420 Maytag: YNED4655EW, YIED4671EW Roper: RED4516FW0, RED4640YQ0, RED4640YQ1, RED4645EW0 Crosley: VDEW6511RW0, VED6505GW0 Amana: NED4655EW0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Crosley, Amana, and other dryers. 🔧 Specifications: Genuine OEM Whirlpool push to start switch with screw terminals, 120V, 2-terminal configuration. 💪 Reliable Performance: Initiates drying cycle with a button press, ensuring consistent operation. 🛠️ Easy Installation: Requires a screwdriver; typically installed in 10–20 minutes. 🛡️ Effective Fixes: Resolves dryer not starting or inconsistent starting issues. Product Specification Part Number: WPW10420741 Component Type: Dryer push to start switch Material: Plastic and brass/stainless steel Electrical Specs: 120V, 2-terminal, normally open, single-pole single-throw (SPST) Compliance: UL-listed, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running smoothly today! Add to cart now for a reliable fix!

Read more less

XPARTCO EXP571 Dryer Door Catch The XPARTCO EXP571 is an aftermarket replacement door catch for electric and gas dryers from Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse, and LG. The door catch is the small plastic part the dryer door latches onto to stay securely shut during a cycle. Keeping the door tightly closed holds heat and airflow inside the drum, so clothes dry efficiently. Over time, regular wear, physical damage, or a door that has drifted out of alignment can cause the catch to crack, wear down, or lose its grip, and the door stops latching reliably. Made from durable plastic, this is a direct-fit replacement with a simple snap-in installation — no tools required. Because the same catch design was used across several appliance families, it carries a long cross-reference list spanning Whirlpool, Frigidaire, and GE part numbers; see the Replaces list below. Each order includes 1 door catch. Quick Answer The XPARTCO EXP571 Dryer Door Catch fixes a dryer door that won't stay closed, won't latch properly, or pops open during a cycle because the catch is cracked, worn, or damaged. Durable plastic, snap-in install with no tools, 1 catch per order. Fits Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse, and LG dryers. Classic symptom: you have to push or hold the door shut, or it swings open mid-cycle and heat escapes. Common Problems This Part Fixes Dryer door won't stay closed or pops open during a cycle Door doesn't latch with a firm, positive click Visibly cracked, broken, or worn catch Heat escaping around the door, leaving clothes damp after a full cycle Door feels loose or misaligned when closed Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door catch directly replaces the following part numbers: WP71002106, WP3389441, 3389441, 71002106, AWP47565, PD00004499, AP6010685, PS11743869, AP6008299, PS11741434, WE1X1195, AGE1230465, AP2042209, PS266896, 131658800, AFR14189, AP2107362, PD00000626, PS418433, 5307521419, 10690002, 10690001, AFR14189, AP4450746, PD00000626, PS418433 This one catch design was sold under the part numbers of several manufacturers: Whirlpool/Maytag (WP71002106, WP3389441), Frigidaire/Electrolux (131658800, 5307521419), and GE (WE1X1195, WE1X1153, WE01X10023, and related). The AP/PS-prefixed numbers are third-party catalog cross-references for the same physical part. Compatibility This door catch is used on dryer models from the following brands: Whirlpool, Maytag, Amana, and Kenmore (Whirlpool-built) dryers Frigidaire, Electrolux, Crosley, White-Westinghouse, and Kenmore (Frigidaire-built) dryers GE dryers Select LG dryers Note: Because this catch was used across so many brands and model years, a full model-number list can't be shown here. The safest way to confirm fit is to match the number on your old catch, or on your dryer's parts diagram, against the Replaces list above rather than relying on brand alone. Contact our support team with your model number and we'll verify before you order. Key Features Aftermarket replacement dryer door catch Durable plastic construction for long-lasting use Simple snap-in installation — no tools required Holds the door securely closed to keep heat and airflow in the drum Cross-references to Whirlpool, Frigidaire, GE, and other OEM numbering 1 door catch per order Product Specifications Part Number EXP571 OEM Part Number WP71002106, 131658800, WE1X1195 Part Type Dryer Door Catch Condition Aftermarket Replacement Material Plastic Quantity 1 Door Catch Installation Snap-In, No Tools Required Application Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse & LG Dryers Installation Notes ℹ️ No Tools Required Unplug the dryer before starting as a general safety precaution. Open the dryer door and locate the worn or broken catch the door latches onto. Pull or pry the old catch free from its mounting position, then press the new catch into the same opening until it snaps firmly into place. Close the door and confirm it latches with a positive click and stays shut. If the door still won't seat or latch evenly after the swap, check the door's alignment and hinges, since a misaligned door can wear out a new catch quickly. Frequently Asked Questions My dryer door won't stay shut — is this the part I need? Very likely. A cracked, worn, or damaged door catch is a common reason a dryer door won't latch or pops open mid-cycle. Inspect the old catch for cracks or wear; if it looks damaged, replacing it should restore a firm latch. Will this fit my dryer? I have a Whirlpool, Frigidaire, or GE. This catch is cross-referenced to part numbers from all three families, plus several others. Match the number on your old catch or your dryer's parts diagram against the Replaces list above. If you're unsure, contact our support team with your model number and we'll confirm fit before you order. Do I need tools to install it? No. It's a simple snap-in design — remove the old catch and press the new one into place until it clicks. How many catches come in this order? Each order includes 1 door catch. The door still doesn't close right after replacing the catch. What else could be wrong? A door that has drifted out of alignment can keep a new catch from seating properly and wear it out fast. Check the door hinges and alignment against the cabinet opening. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO XP6974 Dryer Thermostat Kit Replaces WP3387134, WP3392519, W10900067, 279816 The XPARTCO XP6974 is an aftermarket dryer thermostat kit containing four thermal components for Whirlpool-family electric and gas dryers including Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef. The kit includes the cycling thermostat (WP3387134), thermal fuse (WP3392519), high-limit thermostat and thermal cut-off kit (279816 / W10900067) — the complete set of heat-sensing and safety components that regulate dryer temperature and prevent dangerous overheating. These four components work together to control and protect the dryer's heating system. When any one of them fails, the dryer may produce no heat, overheat, run too long, or stop mid-cycle. Because a failed thermal fuse is almost always caused by an underlying overheating condition that also stresses the other components, replacing all four together in a single repair is the recommended approach. Includes all wiring hardware needed for installation. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO XP6974 Dryer Thermostat Kit fixes Whirlpool-family dryers that produce no heat, overheat, take too long to dry, or stop mid-cycle. Includes all four thermal components: cycling thermostat (L155-25), thermal fuse (196°F), high-limit thermostat (L250-80), and thermal cut-off (309°F). Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef electric and gas dryers. Common Problems This Kit Fixes Dryer produces no heat — thermal fuse or high-limit thermostat has blown Dryer takes multiple cycles or very long time to dry clothes Dryer overheats — clothes or drum too hot to touch after a cycle Dryer shuts off mid-cycle and will not restart Dryer tumbles normally but generates no heat at all Dryer runs too long because cycling thermostat is not regulating temperature Repeated thermal fuse failures — underlying thermostat fault causing recurring overheating What's in the Kit Part 1 of 4 WP3387134 Cycling Thermostat Rated L155-25 · Monitors drum air temperature and cycles the heating element on and off to maintain the set drying temperature · Located on the exhaust duct or blower housing · Should show closed continuity at room temperature Part 2 of 4 WP3392519 Thermal Fuse Opens at 196°F (91°C) · One-time safety device located on the exhaust duct · Permanently interrupts power to the heating element if the dryer overheats · Cannot be reset — must be replaced if blown · Most common cause of no-heat in Whirlpool-family dryers Part 3 of 4 High-Limit Thermostat (279816 / W10900067) Rated L250-80 · Mounted on the heating element housing · Opens at approximately 250°F to cut power to the heating element if temperature exceeds safe limits · Resets automatically when it cools · Should show closed continuity at room temperature Part 4 of 4 Thermal Cut-Off Fuse (3977393 / 279816 kit) Opens at 309°F · Backup one-time safety device on the heating element housing · Permanently interrupts power to the heating element if the high-limit thermostat fails to open · Cannot be reset — must be replaced if blown Replaces Part Numbers WP3387134 Cycling Thermostat cross-references: WP3387134, WP3387134VP, 3387134, 3387135, 3387139, 306910, 3-6910, ET187, AP6008270, PS11741405 WP3392519 Thermal Fuse cross-references: WP3392519, WP3392519VP, 3392519, 3388651, 694511, 80005, ET401, G4AP0500, AP6008325, PS11741460 279816 High-Limit Thermostat and Thermal Cut-Off Kit cross-references: 279816, 279816VP, W10900067, 3977393, 3977767, WP3977767, WP3977767VP, 3399848, 3399693, 2651, AP3094244, AH334299, EA334299, EAP334299, PS334299 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat kit is compatible with select gas and electric dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (Whirlpool-built models) Maytag dryers (gas and electric) Amana dryers KitchenAid dryers Roper dryers Admiral dryers Estate dryers Crosley dryers Inglis dryers Magic Chef dryers Important: If your thermal fuse has blown, always check for the root cause before replacing — a clogged exhaust vent is the most common cause of dryer overheating. Clean the full length of the exhaust duct before or after this repair. If the vent is clear, a failed cycling thermostat or high-limit thermostat is likely the root cause. Key Features Complete 4-part thermal kit — covers the cycling thermostat, thermal fuse, high-limit thermostat, and thermal cut-off in a single repair Cycling thermostat (L155-25) — regulates drum temperature to maintain consistent, efficient drying Thermal fuse (196°F) — one-time safety device that permanently interrupts heat if the dryer overheats High-limit thermostat (L250-80, ~250°F) — cuts power to the heating element when temperature exceeds safe limits; auto-resets Thermal cut-off (309°F) — backup one-time safety device protecting against heating element runaway Replacing all four parts together ensures the complete thermal circuit is renewed — prevents recurrence if a failing thermostat caused the fuse to blow Includes all wiring hardware for installation Compatible with 11 major appliance brands on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Kit Part Number XP6974 Condition Aftermarket Replacement Application Gas and Electric Dryers Kit Includes 1x WP3387134 Cycling Thermostat, 1x WP3392519 Thermal Fuse, 1x High-Limit Thermostat (L250-80), 1x Thermal Cut-Off Fuse (309°F), wiring hardware Cycling Thermostat Rating L155-25 (closes at 155°F, opens at 25°F differential) Thermal Fuse Trip Temp 196°F (91°C) — one-time, non-resettable High-Limit Thermostat Rating L250-80 (opens at ~250°F) — auto-resets Thermal Cut-Off Trip Temp 309°F — one-time, non-resettable Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef Installation Notes ⚠️ Unplug Dryer and Shut Off Gas Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the back panel of the dryer to access the heating element housing and exhaust duct. The thermal fuse (WP3392519) and cycling thermostat (WP3387134) are located on the exhaust duct or blower housing — disconnect the wires, unscrew the mounting screws, and install the new parts in the same positions. The high-limit thermostat and thermal cut-off (279816 kit) are located on the heating element housing — disconnect the wires and unscrew the mounting screws to remove the old parts and install the new ones. Reconnect all wires to the correct terminals — take a photo before disconnecting to reference during reinstallation. Reassemble the back panel, restore power, and run a test cycle to verify heat. Tip: Before running the dryer, also clean the full length of the exhaust duct — a clogged vent is the most common root cause of dryer overheating and repeated thermal fuse failures. Tools needed: Phillips screwdriver, 1/4" nut driver, needle-nose pliers. Frequently Asked Questions What does each part in this kit do? The cycling thermostat (WP3387134) monitors the air temperature in the exhaust duct and cycles the heating element on and off to maintain the correct drying temperature — it is the part that controls how hot the dryer gets during normal operation. The thermal fuse (WP3392519) is a one-time safety device that permanently cuts power to the heating element if the dryer overheats above 196°F — it is the most common cause of no-heat in Whirlpool-family dryers. The high-limit thermostat opens at approximately 250°F to cut heating element power if temperature gets too high, and resets automatically when it cools. The thermal cut-off is a backup one-time fuse on the heating element that opens at 309°F if the high-limit thermostat fails to protect the heater. Why should I replace all four parts instead of just the one that failed? When a thermal fuse blows, it almost always blew because the dryer overheated — and that overheating event put significant stress on all the other thermal components as well. A failing cycling thermostat is the most common cause of repeated thermal fuse failures: if the cycling thermostat stops regulating temperature correctly, the dryer runs too hot, the high-limit thermostat is repeatedly stressed, and the thermal fuse eventually blows. Replacing just the fuse without replacing the cycling thermostat means the same overheating will blow the new fuse. Replacing all four parts at once eliminates that risk in a single repair. How do I test these parts with a multimeter? Set the multimeter to continuity or resistance mode. The thermal fuse (WP3392519), cycling thermostat (WP3387134), and high-limit thermostat should all show closed continuity (near-zero resistance) at room temperature. The thermal cut-off should also show closed continuity at room temperature. Any part that reads open (no continuity / infinite resistance) at room temperature has failed and needs to be replaced. A blown thermal fuse or cut-off will always read open — they are one-time devices and cannot reset. What causes the thermal fuse to blow repeatedly? The most common cause by far is a clogged exhaust vent — lint accumulation inside the dryer duct restricts airflow, causing heat to build up inside the dryer cabinet until the thermal fuse trips. Always clean the full length of the exhaust duct before and after replacing these parts. Other causes include a failing cycling thermostat that is not regulating temperature correctly, a stuck heating element relay, or a dryer placed in an enclosed space without adequate ventilation. Is this kit compatible with both electric and gas dryers? Yes — the XP6974 kit is compatible with both electric and gas Whirlpool-family dryers. Both types use the same cycling thermostat (WP3387134) and thermal fuse (WP3392519). The high-limit thermostat and thermal cut-off (279816 kit) are located on the heating element in electric models and on the burner assembly area in gas models. Always verify your specific model number before ordering to confirm all four parts apply to your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WP8577891 Genuine OEM Whirlpool Dryer High-Limit Thermostat The WP8577891 is a genuine Whirlpool OEM high-limit thermostat for Whirlpool, Maytag, Jenn-Air, Kenmore, KitchenAid, Amana, Magic Chef, Admiral, Norge, and Roper dryers. This part combines two functions in a single component: it acts as a safety mechanism that shuts off the heating element when the dryer overheats, and it includes an inlet thermistor that monitors the temperature of the inlet air feeding into the dryer. Rated L260-68F: the heating element cuts out once internal temperature reaches 260°F, and kicks back in once temperature drops to 192°F, a 68°F differential built into the design. Weighing approximately 0.08 lbs, with package dimensions of 4.33" x 3.43" x 0.79". Because this is a safety-critical component, a malfunctioning thermostat can shut off the dryer even when it isn't actually overheating, in addition to producing the more expected overheating symptom if it fails to trip when it should. Symptoms include the dryer overheating, blown thermal fuses, or the dryer shutting off unexpectedly during a cycle. It directly replaces 8577891, 314654, AP6013527, AWP48573, EAP11746753, OEM18040590, L260-68F, L126.7-37.7C, PD00003286, PS11746753. Quick Answer The WP8577891 Genuine OEM Whirlpool Dryer High-Limit Thermostat fixes Whirlpool, Maytag, Jenn-Air, Kenmore, KitchenAid, Amana, Magic Chef, Admiral, Norge, and Roper dryers with overheating, blown thermal fuses, or unexpected shutoffs during a cycle. L260-68F rating. Replaces 8577891, 314654, AP6013527, AWP48573, EAP11746753, OEM18040590, L260-68F, L126.7-37.7C, PD00003286, PS11746753. Test the old thermostat's continuity with a multimeter before ordering — one customer found this quick check would have confirmed the part was actually needed before they bought a replacement. Common Problems This Part Fixes Dryer overheating during a cycle Dryer blowing thermal fuses repeatedly Dryer shutting off unexpectedly, even when it doesn't seem to be overheating Dryer not heating properly due to a malfunctioning safety cutoff Irregular or inconsistent drying cycles Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer high-limit thermostat directly replaces the following OEM and cross-reference part numbers: WP8577891, 8577891, 314654, AP6013527, AWP48573, EAP11746753, OEM18040590, L260-68F, L126.7-37.7C, PD00003286, PS11746753 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This high-limit thermostat is compatible with select Whirlpool electric dryers, and also fits select Maytag, Jenn-Air, Kenmore, KitchenAid, Amana, Magic Chef, Admiral, Norge, and Roper dryers built on the Whirlpool platform, including model numbers such as MED6600TQ0, WED6200SW0, WED6200SW1, WED6600VU0, WED6600VW0, WED6600WL0, YMED6600TQ0, YWED6200SW1, YWED6600VU0, YWED6600VW0, and YWED6600WL0. Note: Always verify your full model number before ordering, since Whirlpool uses different high-limit thermostat designs across its dryer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified opening and reset temperatures Combines high-limit thermostat and inlet thermistor functions in one component Resolves "overheating," "blown thermal fuses," and "unexpected shutoff mid-cycle" symptoms L260-68F rating — opens at 260°F Automatically resetting — no replacement needed after each trip Direct drop-in replacement matching the original mounting and terminal configuration Replaces 8577891, 314654, AP6013527, AWP48573, EAP11746753, OEM18040590, L260-68F, L126.7-37.7C, PD00003286, PS11746753 Compatible with Whirlpool, Maytag, Jenn-Air, Kenmore, KitchenAid, Amana, Magic Chef, Admiral, Norge, and Roper dryers Genuine OEM replacement — guaranteed fit, materials, and performance Approximately 30-minute repair Product Specifications Part Number WP8577891 Part Type Dryer High-Limit Thermostat with Inlet Thermistor Condition Genuine OEM Brand Whirlpool Rating L260-68F Type Automatically resetting Weight Approx. 0.08 lbs Package Dimensions 4.33" x 3.43" x 0.79" Repair Difficulty Easy — approx. 30 minutes Quantity 1 high-limit thermostat Compatible Brands Whirlpool, Maytag, Jenn-Air, Kenmore, KitchenAid, Amana, Magic Chef, Admiral, Norge, Roper Installation Notes ⚠️ Unplug Dryer Before Starting — Test With A Multimeter Before Assuming It's This Part Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Unscrew and remove the dryer's exhaust vent hose, then use a nut driver to remove the back panel. Locate the high-limit thermostat, typically mounted near the heating element housing. Before removing the old part, test it with a multimeter set to continuity — a healthy thermostat shows continuity; one that doesn't should be replaced. Photograph the wiring before disconnecting anything. Disconnect the wire terminals from the old thermostat, remove its mounting screw, and pull it free. Install the new WP8577891 in the same position, reconnect the wire terminals, and secure the mounting screw. Reattach the back panel and exhaust vent hose. Restore power and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: nut driver, flat-head screwdriver, multimeter, work gloves. Frequently Asked Questions How do I know if this thermostat has actually failed before I order one? Test the old thermostat with a multimeter set to continuity before ordering — it's a simple, quick check. One customer specifically noted they wished they had tested the part first: they ordered a replacement, then discovered testing the old one with a multimeter was easy to do and would have confirmed whether they actually needed the new part before buying it. My dryer shuts off even though it doesn't feel like it's overheating. Could this still be the thermostat? Yes. A malfunctioning high-limit thermostat can shut off the dryer even when actual temperatures are normal, not just when the dryer is genuinely running too hot. If your dryer stops mid-cycle without an obvious overheating cause, this thermostat is worth testing. Should I replace other parts at the same time as this thermostat? If your dryer has also blown a thermal fuse, it's worth replacing the fuse and any related thermal cutoff components together with this thermostat, since they often fail from the same underlying overheating cause. Also check your exhaust venting for restrictions while you have the dryer open, since blocked airflow is a common root cause of repeated thermal component failures. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original opening and reset temperatures and mounting configuration of the high-limit thermostat originally installed in your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

279769 Genuine OEM Whirlpool Dryer Thermostat Kit The 279769 is a genuine Whirlpool OEM thermal cut-off and high-limit thermostat kit for Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers. This kit bundles two components that guard against overheating at different thresholds: the 3390291 high-limit thermostat (rated L250-80F) monitors internal temperature and interrupts power at approximately 250°F to prevent overheating, then resets itself automatically once the dryer cools — no replacement needed after each trip. The 3977394 thermal cut-off fuse is the backup: rated at 352°F, it's a one-time safety device that permanently opens the circuit if temperatures climb high enough that the thermostat alone didn't prevent an overheat. These two parts are sold together and should be replaced together as a set, since they protect the same circuit and tend to be stressed by the same underlying problem. Whirlpool's own guidance is direct: when the thermal cut-off fails, it usually indicates a venting problem, and failing to correct that airflow issue will cause repetitive failures even with new parts installed. Symptoms include the dryer not heating, clothes coming out extremely hot, or the dryer not running at all. This kit is commonly used alongside heating element 4391960. It directly replaces 279548, 2796769, 279769VP, 2821, 2004, 3387812, 3389946, 3398671, 3977394, 695563, 80001, SET184, SET198, TJSET198, ET184, AP3094224, AH334278, EA334278, EAP334278, PD00002485, PS334278, WP3390291, AP6008306, 3390291, 696397, and PS11741441. Quick Answer The 279769 Genuine OEM Whirlpool Dryer Thermostat Kit fixes Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers with no heat, no power at all, or clothes coming out dangerously hot. Includes the 3390291 high-limit thermostat (250°F, auto-resetting) and the 3977394 thermal cut-off fuse (352°F, one-time). Replaces 279548, 2796769, 279769VP, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AP3094224, PS334278, WP3390291, AP6008306, 3390291, 696397, PS11741441. Always inspect and clean the exhaust venting when replacing this kit — a blown thermal fuse is a symptom of restricted airflow, and skipping the vent check leads to repeat failures. What's In The Kit Component Rating Function 3390291 High-Limit Thermostat L250-80F (~250°F) Interrupts power to prevent overheating, resets automatically once the dryer cools. 3977394 Thermal Cut-Off Fuse 352°F One-time backup safety device — permanently opens the circuit if temperature exceeds safe limits. Cannot reset. Common Problems This Kit Fixes Dryer won't start at all — no lights, no tumble, no response Dryer runs but produces no heat Clothes coming out extremely hot, hot enough to be uncomfortable to handle Dryer that stopped working suddenly after running unusually hot Repeated thermal cut-off failures on a dryer with a known venting issue Dryer that shuts off prematurely mid-cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermostat kit directly replaces the following OEM and cross-reference part numbers: 279769, 2004, 279548, 2796769, 279769VP, 2821, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AH334278, EA334278, AP3094224, OEM9282681, SET184, SET198E, AP334278, L250-80F, PS334278, AWP39149, PD00002485. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat kit is compatible with select Whirlpool electric dryers, and also fits select Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral dryers built on the Whirlpool platform, including model numbers such as: 7MWET4027HW0 WET3300XQ0 WET4027EW0, WET4027EW1 WET4027HW0, WET4027HW1, WET4027HW2 WETLV27FW0, WETLV27HW0, WETLV27HW1, WETLV27HW2, WETLV27HW3 YWET4027EW1, YWET4027HW0, YWET4027HW1, YWET4027HW2 Note: This kit was used on Whirlpool-built electric dryers primarily from 1985 to 1995. Always verify your full model number before ordering, since Whirlpool used several different thermostat and fuse designs across its dryer lineup over the years. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified thresholds for both components 2-piece kit: 3390291 high-limit thermostat (250°F, auto-resetting) and 3977394 thermal cut-off fuse (352°F, one-time) Resolves "no heat," "no power at all," and "clothes coming out extremely hot" symptoms Addresses two overheat-protection thresholds in the same circuit at once Commonly used alongside heating element 4391960 Direct drop-in replacement for both original components Replaces 279548, 2796769, 279769VP, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AP3094224, PS334278, WP3390291, AP6008306, 3390291, 696397, and PS11741441 Compatible with Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Kit Part Number 279769 Kit Contents 1x High-Limit Thermostat (3390291), 1x Thermal Cut-Off Fuse (3977394) Condition Genuine OEM Brand Whirlpool High-Limit Thermostat Rating L250-80F (~250°F, auto-resetting) Thermal Fuse Rating 352°F (one-time, non-resettable) Companion Heating Element 4391960 (commonly used together) Repair Difficulty Easy to Moderate — basic tools required Compatible Brands Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, Admiral Installation Notes ⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel, near the heating element and blower housing where both components are mounted. Photograph the wiring connections before disconnecting anything, since the thermostat and fuse can be easy to swap positions by mistake. Remove each old component from its mounting position, noting orientation, and disconnect its wiring. Before reassembling, fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. When the thermal cut-off fails, it usually indicates a venting problem, and failing to correct that airflow issue will cause repetitive failures even with these new parts installed. Install the new 3390291 thermostat and 3977394 thermal fuse from this kit in the same positions as the parts they replace, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), work gloves. Frequently Asked Questions My clothes are coming out extremely hot, hot enough to burn my hands. Is this the right kit? Yes, this is a documented symptom this kit addresses. If the high-limit thermostat fails to regulate temperature correctly, the dryer can run far hotter than it should, producing dangerously hot clothing at the end of a cycle. Whirlpool's own parts support has specifically pointed customers with this exact complaint toward this kit. Stop using the dryer if you notice this symptom and replace both components promptly. Why do I need to replace both the thermostat and the fuse together? These two parts protect the same circuit at different thresholds and tend to fail from the same underlying cause. If the high-limit thermostat isn't regulating temperature correctly, the thermal fuse often ends up blowing as the backup safety measure. Replacing only one risks the other failing again shortly after, so they're sold and serviced together as a set. I replaced this kit and the dryer failed again. What should I check? This is a strong sign the underlying cause — almost always restricted airflow — was never addressed. Thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. Failing to correct a venting issue will cause repetitive failures of this kit even when it's brand new. Should I replace the heating element at the same time? It's worth considering if your dryer's heating element (commonly 4391960 on compatible models) is original and has been running alongside a failing thermostat, since sustained overheating can stress the element as well. It's not required, but since you'll already have the panel open for this repair, it's a reasonable time to inspect the element for visible damage. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same temperature thresholds and mounting configuration as the high-limit thermostat and thermal cut-off fuse originally installed in your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less