Search results for "dryer belts and idler pulley"

W11568627 Genuine OEM Whirlpool/Kenmore Dryer Drum Belt The W11568627 is a genuine OEM drum (cylinder) belt for select Whirlpool and Kenmore front-load dryers. This belt wraps around the outside of the drum and routes around the drive motor pulley and idler pulley — it's what actually spins the drum during a drying cycle while the motor and blower keep running independently. Over time this belt stretches, glazes, or cracks from heat and friction, and it eventually slips or snaps, leaving the drum motionless even though the rest of the dryer still runs. Manufactured by Whirlpool to factory spec for smooth, durable drum operation under high-demand drying cycles, this is a genuine OEM part — not an aftermarket equivalent — so fit and long-term performance match what came on the dryer originally. Quick Answer The Genuine OEM W11568627 Dryer Drum Belt fixes a Whirlpool or Kenmore dryer whose drum won't spin, or that runs with a rubbing/thumping noise from the drum area. Genuine OEM replacement, factory fit. Classic symptom: motor and airflow run normally, but the drum sits still — or a rubbing sound right before the belt fails completely. Common Problems This Part Fixes Dryer runs (motor and airflow work) but the drum doesn't spin Rubbing, squealing, or thumping noise from inside the dryer during operation Clothes bunch up in one spot instead of tumbling Burning rubber smell from a slipping or overheating belt Visible cracking, glazing, or fraying on the old belt Dryer drum spins freely by hand with no resistance from the motor Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drum belt directly replaces the following part number: W11568627, W10577771, AP7175918, AWP45299, EAP16660508, OEM21527763, PD00070745, PS16660508 W10577771 is the previous Whirlpool part number for this belt; W11568627 is the current production number. We were not able to confirm additional cross-reference numbers beyond these two at this time. If you have one, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with the following Whirlpool and Kenmore dryer models: 11061632610, 11061632611 11061633610, 11061633611, 11061633612 11071632610, 11071633610, 110C61633610 WED9500EC0, WED9500EW0, WGD9500EC0, WGD9500EW0 Note: Not all applicable models are necessarily listed above — this is the compatibility data we were able to confirm from available sourcing, and Whirlpool may use this belt on additional models not shown here. Confirm the belt shown on your dryer's parts diagram matches this part number, or contact our support team with your model number to verify before ordering. Key Features Genuine OEM drum belt — factory fit and durability, not an aftermarket equivalent Drives drum rotation during the drying cycle Built for smooth, reliable operation under high-demand drying cycles Resolves drum-not-spinning, rubbing/thumping noise, and slipping-belt symptoms Direct replacement for both W11568627 and the earlier W10577771 numbering One-year manufacturer replacement warranty on genuine parts Product Specifications Part Number W11568627 OEM Part Number W11568627 Part Type Dryer Drum (Cylinder) Belt Condition Genuine OEM Application Whirlpool & Kenmore Dryers Country of Origin Mexico Installation Notes ℹ️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Remove the dryer's front or rear access panel per your model's service guide to reach the drum, motor pulley, and idler pulley. Release tension on the idler pulley to slip the old belt off, and note the belt's routing path around the drum and pulleys before removing it — a photo taken beforehand makes reinstallation much easier. Loop the new belt around the drum with the ribbed side against the drum surface, then route it around the motor pulley and back around the idler pulley in the same path as the original, making sure it isn't twisted. Reinstall the idler pulley to restore proper tension, then rotate the drum by hand to confirm the belt tracks straight and doesn't rub before closing up the panel. Frequently Asked Questions My dryer runs but the drum won't turn — is this the part I need? Yes, in most cases. A broken or badly slipped drum belt is the most common cause of a dryer that powers on, runs the motor and blower, and still produces heat and airflow, but the drum itself sits motionless. Is W10577771 the same belt as W11568627? Yes. W10577771 was the earlier Whirlpool part number for this belt; W11568627 is the current production number for the same design. If your dryer's parts diagram shows W10577771, this part is the correct current replacement. My exact model isn't listed — will this still fit? Possibly. Whirlpool uses this belt across a range of models beyond what's confirmed in our current compatibility data. Contact our support team with your full model number and we'll verify fit before you order. Do I need to replace the idler pulley at the same time? Not necessarily — this listing is for the belt only. However, if your idler pulley is worn, noisy, or doesn't spin freely, it's worth inspecting and replacing while the dryer is already apart, since a bad idler pulley can shorten the life of a new belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 511255P Dryer Drum Belt Replaces D511255P The XPARTCO 511255P is an aftermarket replacement drum (cylinder) belt for Speed Queen and Alliance Laundry Systems commercial and residential dryers. This belt wraps around the outside of the drum and loops over the drive motor pulley and idler pulley, and it's what actually spins the drum during a drying cycle. Over years of use the rubber-faced belt stretches, glazes over, or cracks, and it eventually slips or snaps — when that happens the drum stops turning even though the motor and blower are still running. The telltale sign of a worn or broken drum belt is a dryer that powers on and runs (you can hear the motor and airflow) but the drum sits still, or a rubbing/thumping noise as a worn belt starts to slip against the drum and idler pulley before it fails completely. This is a direct-fit aftermarket replacement built to the same length, width, and rib profile as the OEM belt it replaces. Quick Answer The XPARTCO 511255P Dryer Drum Belt fixes a Speed Queen or Alliance Laundry dryer whose drum won't spin, or that runs with a rubbing/squealing noise from the drum area. Direct-fit aftermarket replacement for OEM D511255P. Classic symptom: motor runs and you feel warm air, but the drum sits still — or a loud thump/rub right before the belt lets go completely. Common Problems This Part Fixes Dryer runs (motor and airflow work) but the drum doesn't spin Rubbing, squealing, or thumping noise from inside the dryer during operation Clothes bunch up in one spot instead of tumbling Burning rubber smell from a slipping or overheating belt Visible cracking, glazing, or fraying on the old belt Dryer drum spins freely by hand with no resistance from the motor Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drum belt directly replaces the following part numbers: D511255P, 511255P, 435P3, 510178, 511255, 59174, D511255, AP6285392, ASQ376048, EAP12195395, OEM18856185, PD00040572, PS17001086, TU21423, TU21653 This belt is used across Speed Queen, Alliance Laundry Systems, and Kenmore-badged dryers built on Speed Queen platforms — the cross-reference numbers above span all of those labelings for the same physical belt. Compatibility This drum belt is compatible with a wide range of Speed Queen and Alliance Laundry Systems dryers, including model families such as: SSET07QF, SSG119WF, SDG109WF1124, SDEA07WJ SSE107LF99L6, SDEA07LJ, FGU17AWF1702, KGS18AWF ADE3LRGS171TW01, ADEE9RGS175TW01, ADG4BRGS115TW01, and hundreds of additional Speed Queen commercial and residential model numbers Note: Speed Queen and Alliance Laundry used this belt design across an unusually large number of commercial and residential model numbers spanning many production years — the list above is only a sample. Confirm the belt shown on your dryer's parts diagram matches this part number, or contact our support team with your model number to verify before ordering. Key Features Direct-fit aftermarket drum belt for Speed Queen & Alliance Laundry dryers Rubber-faced construction matching OEM length, width, and rib profile Resolves drum-not-spinning, rubbing/thumping noise, and slipping-belt symptoms Built for both commercial and residential Speed Queen dryer platforms Straightforward swap using the existing idler pulley and tensioner spring Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XP511255P OEM Part Number D511255P Part Type Dryer Drum (Cylinder) Belt Condition Aftermarket Replacement Belt Style Rubber-Faced Cylinder Belt Application Speed Queen & Alliance Laundry Systems Dryers Repair Difficulty Moderate (typically 30–60 minutes) Installation Notes ℹ️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Remove the dryer's rear or front access panel per your model's service guide to reach the drum, motor pulley, and idler pulley. Release tension on the idler pulley to slip the old belt off, and note the belt's routing path around the drum and pulleys before removing it completely — a photo taken beforehand makes reinstallation much easier. Loop the new belt around the drum with the ribbed side against the drum surface, then route it around the motor pulley and back around the idler pulley in the same path as the original, making sure it isn't twisted. Reinstall the idler pulley to restore proper tension, then manually rotate the drum by hand to confirm the belt tracks straight and doesn't rub before closing up the panel. Frequently Asked Questions My dryer runs but the drum won't turn — is this the part I need? Yes, in most cases. A broken or badly slipped drum belt is the most common cause of a dryer that powers on, runs the motor and blower, and still produces heat and airflow, but the drum itself sits motionless. Why does my dryer make a rubbing or thumping noise before the belt fails? As the belt wears, it can glaze over, stretch, or fray, causing it to slip against the drum or idler pulley and produce a rubbing, squealing, or thumping sound. This is usually a sign the belt is close to failing completely and should be replaced soon. Does this fit both commercial and residential Speed Queen dryers? This belt design is shared across a very wide range of Speed Queen and Alliance Laundry Systems models, both commercial and residential. Still, confirm against your dryer's model number or parts diagram before ordering since Speed Queen has used several belt variants over the years. Do I need to replace the idler pulley or tensioner spring at the same time? Not necessarily — this listing is for the belt only. However, if your idler pulley is worn, noisy, or doesn't spin freely, it's worth inspecting and replacing while the dryer is already apart, since a bad idler pulley can shorten the life of a new belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XP12002777 Dryer Idler Pulley and Spring Replaces Part Numbers:12002777, 1401171, 35001083, 35001098, 35001276, AH2004052, AP4010261, DC61-01215A, DC96-00882B, EA2004052, PS2004052.   This is an aftermarket part that can be used as a replacement for the OEM part. WARNING: California’s Proposition 65 (California Residents Only)

Read more less

WP40111201 Genuine OEM Whirlpool Dryer Drum Belt The WP40111201 is a genuine Whirlpool OEM drum belt for full-size Whirlpool-built dryers. The belt is a long, slender loop that wraps all the way around the outside of the drum, passes around the tension (idler) pulley, and loops around the drive motor pulley. This belt is the sole mechanical connection between the motor and the drum — there is no gear or direct coupling — so when it breaks or slips off, the dryer behaves in a very specific way: the console lights up, the motor runs, the blower moves air, but the drum sits still. Open the door and spin the drum by hand and it will turn freely with no resistance. This belt measures 93-3/8 inches long and 3/8 inch wide, with a 5-rib multi-groove profile. Belts fail from age and heat: the rubber hardens over years of thermal cycling, the ribs glaze over and begin slipping under a wet load, and eventually the belt cracks through or snaps outright. A screeching or squealing noise, a rhythmic thump timed to drum rotation, fraying at the edges, or black rubber dust in the cabinet are all signs a belt is near the end of its life. As a genuine OEM part, the WP40111201 is manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It directly replaces 40111201, WP40111201VP, 14218936, 40051501, 40051502, 59174, 821089, AP6009126, PS11742271, and R0606549. Quick Answer The WP40111201 Genuine OEM Whirlpool Dryer Drum Belt fixes full-size Whirlpool-built dryers where the motor runs but the drum won't turn, the drum spins freely by hand, or the dryer screeches, squeals, or thumps during operation. 93-3/8" long, 3/8" wide, 5-rib profile. Replaces 40111201, WP40111201VP, 14218936, 40051501, 40051502, 59174, 821089, AP6009126, PS11742271, R0606549. Grooves face against the motor pulley on this platform — same orientation as our Y312959 belt. Common Problems This Part Fixes Dryer runs and hums but the drum does not turn — the classic broken belt symptom Drum spins freely by hand with no resistance when the door is open Loud screeching or squealing that begins as soon as the cycle starts Rhythmic thumping or slapping noise timed to drum rotation — cracked or split belt Grinding or rumbling from inside the cabinet as a frayed belt drags Drum turns slowly, intermittently, or stalls under a heavy wet load — glazed belt slipping Dryer won't start, or inadequate heating reported alongside a belt-related noise Black rubber dust or belt fragments found in the bottom of the cabinet Visible cracking, fraying, glazing, or stretching on the old belt Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer drum belt directly replaces the following OEM and cross-reference part numbers: WP40111201, 40111201, 14218936, 40051501, 40051502, 59174, PD00002505, EAP11742271, AP6009126, AWP47792, PS11742271, R0606549, WP40111201VP, 661570V, 661570, 3387610, 3389728, 3393999, 339728, 661570VP, AP5983729, PS11722115. 40111201 is the long-running legacy Whirlpool number and WP40111201 is the current part number carrying the "WP" prefix. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select full-size Whirlpool-built dryers across the Whirlpool family of brands, including: Whirlpool electric and gas dryers Maytag dryers (select Whirlpool-built models) KitchenAid dryers (select models) Amana dryers (select models) JennAir dryers (select models) Kenmore dryers (select Whirlpool-built models, including SDG3606AWW) Roper, Estate, Admiral, Crosley, Inglis, Magic Chef, and Norge dryers (select models) This belt fits a large number of standard full-size front-load dryers used across North America. Because the compatible model list spans many years and revisions, always verify your full model number against your dryer's data label before ordering. Note: Whirlpool and Maytag use more than one length of drum belt across their dryer lineups, and belts of a similar rib count and width are not automatically interchangeable. This belt is 93-3/8" long — it is NOT the same belt as our 100"-long Y312959 belt used on other Maytag/Whirlpool platforms. A belt that's too long or too short for your drum will slip, walk off the pulley, or fail to seat properly. Measure your old belt or verify your model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified length, rib profile, and tension 93-3/8" length, 3/8" width, 5-rib multi-groove design Wraps around the drum, tension pulley, and drive motor pulley to transfer motor rotation to the drum Resolves "motor runs but drum won't turn," "screeching," "squealing," and "drum spins freely by hand" symptoms Multi-rib construction grips the motor pulley without slipping under heavy wet loads Direct drop-in replacement — no cutting, splicing, or modification required Replaces 40111201, WP40111201VP, 14218936, 40051501, 40051502, 59174, 821089, AP6009126, PS11742271, and R0606549 Compatible with Whirlpool, Maytag, KitchenAid, Amana, JennAir, Kenmore, Roper, Estate, Admiral, Crosley, Inglis, Magic Chef, and Norge dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WP40111201 Part Type Dryer Drum Drive Belt Condition Genuine OEM Brand Whirlpool Length 93-3/8 in. Width 3/8 in. Ribs 5 Material Reinforced rubber Rib Orientation Grooves face against the motor pulley Routing Around drum → tension pulley → drive motor pulley Fuel Type Electric and gas dryers Quantity 1 belt Compatible Brands Whirlpool, Maytag, KitchenAid, Amana, JennAir, Kenmore, Roper, Estate, Admiral, Crosley, Inglis, Magic Chef, Norge Installation Notes ⚠️ Unplug Dryer Before Starting — Photograph Belt Routing First Disconnect power at the outlet or shut off the circuit breaker before beginning. On a gas model, also close the gas shutoff valve before moving the cabinet. Wear work gloves — sheet metal edges inside the cabinet are sharp. Pull off the lint trap and remove the screws securing the top panel, then raise the panel and support it with a block of wood. Remove the rear access panel to locate the motor, blower wheel, and belt. Photograph how the old belt routes around the drum, the tension pulley, and the motor pulley before removing anything — if the belt is already broken, note that the grooved side of this belt rides against the motor pulley, with the smooth back facing the drum. Loosen and remove the motor mount, lift the motor slightly, and slide the old belt free. The front panel typically needs to come off as well to fully access the drum. Vacuum out accumulated lint while the cabinet is open — lint buildup around the motor and idler is what cooks belts prematurely. Place the new belt around the drum, seat it in the polished wear track left by the old belt, then route it around the tension pulley and around the motor pulley. Useful trick: tape the belt loosely to the drum with a strip of masking tape before repositioning the motor, so it doesn't slide off while you work. Re-secure the motor mount, then rotate the drum by hand several full turns and confirm the belt tracks straight and stays centered without walking toward an edge. While you're in there, spin the tension pulley and each drum roller by hand — if any is noisy, gritty, or has play, replace it now, since a seized pulley or worn roller will destroy the new belt quickly. Reassemble the front and rear panels and the top panel, restore power, and run a short empty cycle listening for squeal or thump before loading it. Tools needed: Phillips screwdriver, 5/16" nut driver, flat-blade screwdriver, putty knife, masking tape, work gloves. Frequently Asked Questions How do I confirm the belt is broken and not the motor? With the dryer unplugged, open the door and try to spin the drum by hand. An intact belt gives firm resistance, because you're turning the motor and idler through the belt. If the drum coasts freely like a bicycle wheel, the belt is broken or has jumped off its pulleys. Sound is the other tell: with a broken belt the motor hums and the blower whooshes normally, so the dryer sounds like it's running perfectly while the drum sits still. A failed motor usually buzzes and does nothing, or trips the breaker outright. What's the difference between WP40111201 and 40111201? They are the same belt across production revisions. 40111201 was the long-running legacy Whirlpool number and WP40111201 is the current number carrying the "WP" prefix Whirlpool adopted. WP40111201VP is a variant packaging code for the same belt. If your dryer's parts diagram or the old belt itself shows any of these numbers, this listing is the correct replacement. The remaining cross-references (14218936, 40051501, 40051502, 59174, 821089, AP6009126, PS11742271, R0606549) are catalog identifiers used by various parts distributors for the same belt. Is this the same belt as your Y312959 listing? No. This belt is 93-3/8" long, while the Y312959 belt in our catalog is 100" long — the two are used on different Maytag/Whirlpool dryer platforms and are not interchangeable. Both share a similar 5-rib profile and grooves-against-motor-pulley orientation, which is exactly why they're easy to confuse. Always check your model number or measure your old belt's length before ordering either one. Which way do the grooves face on this belt? On this Whirlpool platform, the grooved (ribbed) side of the belt rides against the motor pulley, with the smooth back of the belt facing the drum. This is the same orientation as our Y312959 belt, but it is the opposite of some other manufacturers' platforms — for example, Frigidaire's 134719300 belt runs with the grooves facing down against the drum instead. Always confirm orientation for your specific brand and platform, and photograph the old belt before removing it whenever possible. The dryer squeals but the drum still turns. Belt or something else? Could be either, and it's worth diagnosing before you order. A glazed or hardening belt squeals as it slips on the motor pulley, usually loudest at startup and under a heavy wet load. But a dry tension pulley bearing makes a very similar squeal, and worn drum rollers add a low rumble underneath. With the cabinet open, spin the tension pulley and each roller by hand — they should turn smoothly and silently. If they're gritty, noisy, or have play, replace them along with the belt, since they share the same teardown and you'd otherwise be opening the dryer twice. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original 93-3/8" length, 3/8" width, and 5-rib profile of the drum belt originally installed in your Whirlpool, Maytag, KitchenAid, Amana, or related dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WE03X32037 Dryer Drum Belt Replaces WE12M24 The XPARTCO WE03X32037 is an aftermarket replacement drum drive belt for GE, Hotpoint, and RCA portable, compact, and unitized stack dryers. The belt is a long, slender loop that wraps all the way around the outside of the drum, passes around the idler tension pulley, and finishes around the small drive motor pulley. That belt is the only mechanical link between the motor and the drum — there are no gears and no direct coupling — so when it breaks, the dryer behaves in a very specific way: the console lights up, the motor runs, the blower moves air, and the drum simply sits there. Open the door and spin the drum by hand and it coasts freely with no resistance at all. This belt measures approximately 79 inches long and about 1/4 inch wide, with a 4-rib multi-groove profile molded into the inner face. The 79" length is the defining specification here — GE uses several visually similar 4-rib dryer belts across its lineup, and the difference between them is length. Belts fail from heat and age: the rubber hardens, the ribs glaze and begin slipping under a heavy wet load, and eventually the belt cracks through or snaps. Fraying edges, a squeal at startup, a rhythmic thump timed to drum rotation, or black rubber dust in the bottom of the cabinet all point to a belt nearing the end of its life. It directly replaces WE12M24, WE12M9, WE12X79, WE12X0079, AP3418890, AP7186820, PS755943, and related numbers. Installs in 45–90 minutes with basic hand tools. Quick Answer The XPARTCO WE03X32037 Dryer Drum Belt fixes GE, Hotpoint, and RCA portable, compact, and stack dryers where the motor runs but the drum won't turn, the drum spins freely by hand, or the dryer squeals, thumps, or rumbles during a cycle. Approximately 79" long, 1/4" wide, 4 ribs, black rubber. Fits DDP1370/DDP1375/DDP1380 portable and DSKP333/DSKS333/DSKS433 stack models. Replaces WE12M24, WE12M9, WE12X79, WE12X0079, AP3418890, AP7186820, PS755943. Not the same belt as the 89-1/2" full-size GE WE12M29 — length is what separates them. Common Problems This Part Fixes Dryer runs and hums but the drum does not turn — the classic broken belt symptom Drum spins freely by hand with no resistance when the door is open Loud squealing or screeching that begins as soon as the cycle starts Rhythmic thumping or slapping noise timed to drum rotation — cracked or split belt Grinding or rumbling from inside the cabinet as a frayed belt drags Drum turns slowly, intermittently, or stalls under a heavy wet load — glazed belt slipping Clothes not drying because the drum isn't tumbling to expose them to airflow Black rubber dust or belt fragments in the bottom of the cabinet Visible cracking, fraying, glazing, or stretching on the old belt Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer drum belt directly replaces the following OEM and cross-reference part numbers: WE03X32037, WE12M24, WE12M9, WE12X79, WE12X0079, AP3418890, AP7186820, PS755943, PS16729246, EAP16729246, AH755943, EA755943, 943874, AGE25647, PD00074729 WE03X32037 is the current GE part number; WE12M24 is the long-running legacy number that most service diagrams and older belts still carry. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select portable, compact, and unitized stack dryers from the following brands: GE portable and compact electric dryers — DDP1370, DDP1375, and DDP1380 series GE unitized stack and Spacemaker laundry centers — DSKP333, DSKS333, and DSKS433 series Hotpoint compact and stack dryers (select GE-built models) RCA compact and stack dryers (select GE-built models) Select Kenmore compact dryers built on the GE platform Verified model numbers include: DDP1370GAM, DDP1370SAM, DDP1370SBM, DDP1375GAM, DDP1375GBM, DDP1375GCM, DDP1375GDM, DDP1375GEM, DDP1375SAM, DDP1375SBM, DDP1380GAM, DDP1380GBM, DDP1380GCM, DDP1380GDM, DDP1380GFM, DDP1380SAM, DDP1380SBM, DDP1380SCM, DDP1380SDM, DDP1380TAM, DSKP333EC0WH, DSKP333EC0WW, DSKP333EC2WW, DSKP333EC3WW, DSKP333EC4WW, DSKP333EC5WW, DSKP333EC6WW, DSKS333EC0WH, DSKS333EC0WW, DSKS333EC2WW, DSKS333EC3WW, DSKS333EC4WW, DSKS333EC5WW, DSKS333EC6WW, DSKS433EA0AA, DSKS433EB3WW, DSKS433EB5WW, DSKS433EB6WW, and DSKS433EB7WW. Note — 79" portable/compact belt only: GE uses several visually identical 4-rib dryer belts that differ only in length, and they are NOT interchangeable. This belt is approximately 79 inches, for portable, compact, and stack units. It is NOT the WE12M29 / WE03X29897 belt (89-1/2") used on full-size GE dryers, NOT the WE12X10009 belt (87"), and NOT the WE12X10014 / WE12X42 belt (87-13/16"). Fitting a longer belt leaves slack the idler cannot take up, and the belt will slip or walk off the pulley within minutes. Measure your old belt end to end, or verify your full model number, before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement drum drive belt — transfers motor rotation to the dryer drum Approximately 79" long, the correct length for GE portable, compact, and unitized stack dryers 4-rib multi-groove profile molded into the inner face for positive grip on the motor pulley 1/4" width matched to the original belt track and idler pulley Durable black rubber construction that resists heat hardening and cracking Resolves "motor runs but drum won't turn," "squealing," "thumping," and "drum spins freely by hand" symptoms Multi-rib design prevents slipping under heavy wet loads where a worn belt would stall Direct drop-in replacement — no cutting, splicing, or modification required Replaces WE12M24, WE12M9, WE12X79, WE12X0079, AP3418890, AP7186820, PS755943, AH755943, EA755943, and 943874 Compatible with GE, Hotpoint, RCA, and select Kenmore compact and stack dryers Aftermarket replacement built to OEM-equivalent quality standards Straightforward DIY repair — installs in 45–90 minutes with basic hand tools Product Specifications Part Number XPWE03X32037 OEM Part Number WE03X32037 (formerly WE12M24) Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application GE Portable, Compact, and Unitized Stack Dryers Length Approx. 79 in. Width 1/4 in. Ribs 4 ribs / 3 grooves Material Rubber Color Black Rib Orientation Ribbed side faces the drum Routing Around drum → idler tension pulley → drive motor pulley Fuel Type Electric and gas dryers Quantity 1 belt Compatible Brands GE, Hotpoint, RCA, select Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Photograph Belt Routing First Disconnect power at the outlet or shut off the circuit breaker before beginning. On a gas model, also close the gas shutoff valve before moving the cabinet. Wear work gloves — the sheet metal edges inside the cabinet are sharp. Before removing anything, photograph how the old belt routes around the drum, around the idler tension pulley, and around the motor pulley. If the belt is already broken and the routing isn't visible, note that the ribbed side of the belt faces toward the drum, with the smooth back riding against the idler pulley. Access on these compact and stack units is generally from the front: remove the top panel, then the control panel and front panel, which frees the drum enough to lift or tilt it forward. Vacuum out accumulated lint while the cabinet is open — restricted airflow and lint packed around the motor are what cook belts prematurely. Slip the new belt around the drum roughly one-third of the way back from the front lip, ribbed side against the drum, and seat it in the polished wear track the old belt left behind. Reach underneath, route the belt around the idler pulley, then loop it around the small motor pulley. Useful trick: tape the belt loosely to the drum with a strip of masking tape before you reach underneath, so it can't slide off while you work the idler into position. Many GE idler arms have a locked or pre-loaded position — if yours does, remember to release it after the belt is seated, or the belt will have no tension and the drum will stall under load. Once routed, rotate the drum several full turns by hand and confirm the belt tracks straight and stays centered without walking toward an edge. While you're in there, spin the idler pulley and each drum roller by hand; if any is noisy, gritty, or has side-to-side play, replace it now, because a seized idler or flat-spotted roller will destroy the new belt quickly. Reassemble, restore power, and run a short empty cycle listening for squeal or thump before loading it. Tools needed: Phillips screwdriver, nut driver or socket set, putty knife, masking tape, flashlight, work gloves. Frequently Asked Questions How do I confirm the belt is broken and not the motor? With the dryer unplugged, open the door and try to spin the drum by hand. An intact belt gives firm resistance, because you're turning the motor and idler through the belt. If the drum coasts freely like a bicycle wheel, the belt is broken or has jumped off its pulleys. Sound is the other tell: with a broken belt the motor hums and the blower whooshes normally, so the dryer sounds like it's running perfectly while the drum sits still. A failed motor usually buzzes and does nothing, or trips the breaker outright. What's the difference between WE03X32037 and WE12M24? They are the same belt across production revisions. WE12M24 was the long-running legacy GE number and WE03X32037 is the current number that supersedes it. If your dryer's parts diagram or the old belt itself shows WE12M24, WE12M9, WE12X79, or WE12X0079, this listing is the correct replacement. The remaining cross-references (AP3418890, AP7186820, PS755943, AH755943, EA755943, 943874) are catalog identifiers used by various parts distributors for the same belt. Can I use a longer GE belt if this one is out of stock? No. GE's 4-rib dryer belts look nearly identical and differ mainly in length, which is precisely why they get substituted by mistake. This belt is about 79"; the full-size GE belt WE12M29 is 89-1/2", and WE12X10009 and WE12X10014 are around 87". On a compact or portable drum, that extra 8 to 10 inches is far more slack than the idler arm can absorb, so the belt runs loose, slips on the motor pulley, and typically walks off within minutes. If you're unsure, lay your old belt flat in a loop and measure its circumference before ordering. Which way do the ribs face? On this GE platform the ribbed side faces toward the drum, so the ribs grip the drum surface while the smooth back of the belt rides against the idler pulley. This is worth stating plainly because rib orientation is not universal across manufacturers — some other platforms run the grooves against the motor pulley instead. Whenever possible, photograph the old belt before removing it. The polished wear track on the drum will also show you exactly where the belt is meant to sit. The dryer squeals but the drum still turns. Belt or something else? Could be either, and it's worth diagnosing before you order. A glazed or hardening belt squeals as it slips on the motor pulley, usually loudest at startup and under a heavy wet load. But a dry idler pulley bearing makes a very similar squeal, and worn drum rollers add a low rumble underneath. With the cabinet open, spin the idler and each roller by hand — they should turn smoothly and silently. If they're gritty, noisy, or have play, replace them along with the belt, since they share the same teardown and you'd otherwise be opening the dryer twice. Why did my belt fail in the first place? Usually heat and age — rubber hardens over years of thermal cycling until it cracks. Two things accelerate it sharply. Restricted airflow from a lint-clogged vent makes the whole cabinet run far hotter than designed, which cooks the belt. And a seized idler pulley or a flat-spotted drum roller forces the belt to drag against a stationary surface, shredding it in short order. If your belt failed unusually early, clean the vent ducting end to end and inspect the idler and rollers rather than assuming the new belt will simply last longer. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the dimensions (approximately 79" length, 1/4" width), 4-rib profile, rubber construction, and drum-drive function of the original WE03X32037 / WE12M24 belt used in compatible GE, Hotpoint, RCA, and related portable, compact, and unitized stack dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

8544742 Dryer Blower Belt - Compatible with Whirlpool, Maytag, Kenmore, Amana Dryers Product Description Restore your dryer’s airflow with the replacement 8544742 Dryer Blower Belt. This high-quality replacement flat belt replaces the Whirlpool 8544742, designed for select Whirlpool, Maytag, Kenmore, Amana, and other brand dryers with a rear blower and top lint filter. Measuring approximately 23.9" long with 3 ribs and 2 grooves, this durable rubber belt connects the motor to the blower wheel, ensuring proper air circulation for efficient drying. It fixes issues like no heat, insufficient heat, long drying times, noisy operation (squeaking or rattling), or the dryer failing to start. Note: The belt is intentionally tight (may appear 1/2" to 1" short) and may require stretching during installation. Inspect the idler pulley (e.g., W10547292) and drum belt (e.g., 8547157) for wear, as they often fail together. Replaces part numbers: WP8544742, 8544742, AP6013111, PS11746333. Compatibility: Compatible with models including but not limited to: Whirlpool: WED8300SW0, WED8300SW1, WED8500SR0, WGD8300SW0, WGD8300SW1, MEDB850WL, MEDB850WB Maytag: 7MMGDB850WL0, 7MMGDB850WL1, MEDB200VQ0, MEDB400VQ1, MEDB700VQ0, MEDB750YW0, MEDB800VB0, MEDB800VQ0, MEDB800VU0, MEDB850WB0 Kenmore: 110.67042600, 110.77086600, 110.87081601 Amana: NED5800DW0, YNED5800DW0 Verify your model number or contact support for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Maytag, Kenmore, Amana, Roper, Admiral, Jenn-Air, Estate, Inglis, KitchenAid, and other dryer models with rear blower and top lint filter. 🔥 Specifications: Flat blower belt, 23.9" long, 0.25" wide, 3 ribs, 2 grooves, made of durable rubber with reinforced construction for stretch resistance. 💰 Cost-Effective Alternative: Replacement belt offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires a Phillips screwdriver, 5/16" nut driver, pliers, and work gloves; typically installed in 30–60 minutes. 🛡️ Reliable Fixes: Resolves no heat, insufficient heat, long drying times, noisy operation, burning smell, or dryer failing to start. Installation Notes: Tools Needed: Phillips screwdriver, 5/16" nut driver, pliers, work gloves, flathead screwdriver. Safety First: Unplug the dryer from the power source and, for gas dryers, shut off the gas valve before installation. Handle with Care: Take photos during disassembly to note belt routing and component placement. Inspect the idler pulley and drum belt for wear, as they can cause blower belt failure. The belt may seem 1/2" to 1" short but is designed to be stretched for a tight fit. Installation Steps: Remove the dryer’s top panel by releasing clips with a putty knife and unscrewing rear screws. Remove the front panel and bulkhead to access the blower assembly (consult your model’s manual for specific screws). Disconnect the old belt from the motor pulley and blower wheel, noting routing. Install the new belt on the blower wheel first, then stretch it onto the motor pulley using pliers or a screwdriver for leverage. Ensure the belt is seated in the grooves. Reassemble in reverse order and test the dryer with a short cycle to confirm proper operation and no leaks or noises. Note: A second person can help with stretching the tight belt. If the belt slips, check for oil on the pulleys or a worn idler pulley. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Get your dryer back to efficient, quiet performance today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO 4400EL2001F Dryer Drum Belt – Compatible with LG & Kenmore Dryers Product Description Restore proper drum rotation and reliable drying performance with the XPARTCO 4400EL2001F Dryer Drum Belt. This high-quality replacement belt, designed for select LG and Kenmore dryers, connects the motor pulley to the drum and idler pulley, enabling efficient tumbling during drying cycles. Made of durable rubber with a 4-rib, 3-groove design, it fixes issues like the drum not turning, loud banging or squeaking noises, or extended drying times due to a worn or broken belt. Note: Includes one 92-inch belt. Inspect drum rollers, idler pulley, and drum for wear during replacement. Clean lint from the drum and cabinet to prevent overheating. Overloading the dryer can cause premature belt failure. Replaces Part Numbers 4400EL2001F, 4400EL2001A, AP4436354, 4PH2337, PS3522928, 4400EL2001C, 4400EL2001E, PD00026116, EAP11705916, AP5972814, PS11705916. Compatibility This replacement dryer drum belt fits select LG and Kenmore (LG-manufactured) electric dryers. Example compatible models include (but are not limited to): LG DLE2516W, DLE7177WM, DLGX3571W, DLE7200WE, DLEX3570V, DLEX3570W, DLEX7600KE, DLEX7600WE, DLEY1901KE, DLEY1901WE, DLG4971W, DLGX5781VE, DLGX5781WE, DLGX7601KE, DLGX7601WE, DLGY1702V, DLGY1902KE, DLEX5101V, DLE5955W, DLE5977S, DLE0442W, DLGX3371V Kenmore 796.80272900, 796.81073310, 79661552610, 79661553610, 79671552610, 79671553610, 79681392610, 79681393610, 79691392610, 79691393610 Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM length, width, and rib pattern 🌀 Restores Drum Rotation – Ensures smooth, consistent dryer operation 🔇 Reduces Noise & Slippage – Helps eliminate squealing or drum stoppage 💪 Heavy-Duty Rubber Construction – Designed for long service life 💰 Cost-Effective Repair – Reliable alternative to OEM dryer belts 📐 Product Specification ✅ Brand and Models Compatibility: Fits select LG and Kenmore dryer models. 🔥 Specifications: 4-rib, 3-groove poly-V belt, black rubber, ~92"L x 1/4"W x 1/16"H, designed for durability and precise fit. 💰 Cost-Effective Alternative: Replacement belt offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires a putty knife, Phillips screwdriver, flat-blade screwdriver, work gloves, optional second person; typically installed in 30–60 minutes. 🛡️ Reliable Fixes: Resolves drum not tumbling, loud noises, or extended drying times. Safety First: Unplug the dryer from the power source and, for gas dryers, shut off the gas valve before installation. 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to prevent electrical shock. Basic Steps: Disconnect dryer power. Open the dryer cabinet and remove the drum. Remove the worn or broken belt. Install the new XPARTCO 4400EL2001F belt around the drum and motor pulley. Reinstall the drum and reassemble the dryer. Restore power and run a test cycle. ⏱️ Time Required: 30–45 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore smooth, reliable dryer operation — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

12638200000241 Genuine OEM Midea Dryer Drum Belt The 12638200000241 is a Genuine OEM Midea replacement dryer drum belt compatible with a wide range of Midea, Criterion, and Insignia electric and gas dryers, including the MLE41/45/47/52, MLG45/52, MLTE37, CDE41, CDG41/45, CLADE67, and MDD160 series. The drum belt wraps around the dryer drum and the motor pulley, transferring the motor's rotation to spin the drum during the drying cycle. When the belt breaks, stretches, or wears out, the motor continues to run but the drum no longer spins — clothes sit still in the drum while the motor hums, and the dryer cannot complete a normal cycle. As a Genuine OEM part manufactured by Midea to factory specifications, the 12638200000241 is constructed from durable black rubber. Packaged dimensions are approximately 11" L x 3" W x 2" H. Note: if the drum belt has failed, this is also a good opportunity to inspect the drum support rollers (Midea 12638000004021) and the idler/tensioner pulley assembly while the dryer cabinet is open — these components wear together and a failing roller or pulley can accelerate belt wear. Installs in 45–60 minutes with basic hand tools. Quick Answer The 12638200000241 Genuine OEM Midea Dryer Drum Belt fixes Midea, Criterion, and Insignia dryers where the motor runs but the drum doesn't spin, the belt has snapped or is visibly stretched, or where there's a burning rubber smell during operation. Black rubber drum belt. Packaged dimensions approximately 11" L x 3" W x 2" H. Genuine OEM. Compatible with Midea MLE41/45/47/52, MLG45/52, MLTE37, CDE41, CDG41/45, CLADE67, MDD160 series, plus Criterion CDE41N1AW/CDG41N1AW/CDG45N1AW and Insignia Midea-built models. Common Problems This Part Fixes Drum not spinning — belt has broken or slipped off Motor runs and hums but the drum stays still Drum spins intermittently — belt slipping under load Burning rubber smell during operation — belt slipping on the motor pulley Squealing or chirping noise during the drying cycle — belt frayed or stretched Belt visibly cracked, frayed, broken, or missing inside the dryer cabinet Extended drying times — drum not rotating at correct speed due to a worn belt Replaces Part Numbers This drum belt directly replaces the following part number: 12638200000241, AP7158561, PS18170626 This is the Midea manufacturer part number used across the compatible Midea, Criterion, and Insignia dryer platform. Contact our support team with your model number if you need confirmation before ordering. Compatibility This drum belt is compatible with select Midea, Criterion, and Insignia electric and gas dryers, including: Midea electric dryers — MLE41N1AWW, MLE45N1AWW, MLE45N1BWW, MLE45N3BMG, MLE45N3BWW, MLE47A3AGG, MLE47C3AWW, MLE47C4AWW, MLE47R5BWW, MLE52N3AWW, MLE52S7AGS, MLE52S7AWW Midea gas dryers — MLG45N1AWW, MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AGS, MLG52S7AWW Midea — MLTE37N1BWW, CLADE67W, MDD160A2301E1305 and related models Criterion — CDE41N1AW (electric), CDG41N1AW (gas), CDG45N1AW (gas) Insignia electric dryers — NSDRE67WH8A, NSFDRE67WH8A, NSFDRE67WH8AC, NSFDRE77WH8B, NSTDRE67W1, NSTDRE75W1 Insignia gas dryers — NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1 Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance Wraps around the dryer drum and motor pulley to transfer the motor's rotation to spin the drum Durable black rubber construction designed for continuous flex and motor load Packaged dimensions: approximately 11" L x 3" W x 2" H Compatible with the full Midea, Criterion, and Insignia electric and gas dryer platform Often replaced along with the drum support rollers (Midea 12638000004021) and idler pulley assembly Installs in 45–60 minutes with basic hand tools Product Specifications Part Number 12638200000241 Part Type Dryer Drum Belt Condition Genuine OEM Application Electric and Gas Dryers (Midea platform) Material Rubber Color Black Packaged Dimensions Approximately 11" L x 3" W x 2" H Often Replaced With Drum Support Roller (Midea 12638000004021) Compatible Brands Midea, Criterion, Insignia Installation Notes ⚠️ Unplug Dryer Before Starting (Shut Off Gas First on Gas Models) — Wear Work Gloves Disconnect power before beginning (and shut off the gas supply first if you have a gas dryer model). Wear work gloves — there are sharp sheet metal edges inside the dryer cabinet. Remove the lint filter housing screws, release the top panel locking clips with a putty knife, and lift the top panel. Disconnect the door switch harness and remove the front panel to access the drum, drive belt, and motor/idler pulley assembly. Take a photo of the existing belt routing before removing anything — this is essential for correct reassembly. Release the old belt from the idler pulley and slide it off the drum and motor pulley. Carefully lift the drum out and inspect the drum support rollers and idler pulley for wear — replace them now if needed while the dryer is open. Wrap the new 12638200000241 belt around the drum (ribbed side against the drum). Reinstall the drum, then route the belt around the motor pulley and under the idler pulley, allowing the idler to tension the belt. Reassemble the front panel and top panel in reverse order. Restore power (and gas, for gas models) and run a test cycle to confirm smooth, quiet drum rotation. Tools needed: Phillips screwdriver, putty knife, work gloves. Frequently Asked Questions How do I know if the drum belt has failed? The clearest sign of a broken drum belt is a dryer where the motor starts and runs normally, but the drum does not spin — you'll hear the motor humming with no drum movement. If you open the door mid-cycle and the drum spins freely with no resistance (as if disconnected from the motor), the belt has either broken or slipped off completely. A stretched or worn belt that still drives the drum may also produce squealing or burning rubber smells from slippage on the motor pulley. Visually inspecting the belt after removing the dryer's front panel confirms the condition. Should I replace the drum rollers and idler pulley at the same time? Yes — since the dryer cabinet must already be opened and the drum removed to replace the belt, this is the ideal time to also inspect and replace the drum support rollers (Midea 12638000004021) and the idler/tensioner pulley. All three components form the drum drive system and tend to wear together. A worn roller or pulley is often what caused the belt to fail prematurely in the first place. Addressing them together in a single repair eliminates the most common drum drive failure points and prevents a near-term repeat teardown. Does this belt fit Insignia and Criterion dryers as well as Midea? Yes — Insignia (Best Buy) and Criterion (Sears/Kmart) are house brands whose dryers in this size class are manufactured by Midea and use the same internal components, including this drum belt. Confirmed compatible models include Insignia NSDRE67WH8A, NSFDRE67WH8A, NSFDRE77WH8B, NSTDRE67W1, NSTDRE75W1 (electric) and NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1 (gas), plus Criterion CDE41N1AW (electric) and CDG41N1AW/CDG45N1AW (gas). Always verify your specific model number before ordering. Which way does the belt go around the drum — ribbed side in or out? On the drum belt, the ribbed (grooved) side should face inward, against the drum surface, while the smooth side faces outward. The ribs grip the smooth drum surface to drive it as the motor pulley turns. On the motor pulley side, the belt seats in the grooves of the small motor pulley. Take a photo of how the original belt was routed before removing it — this is the most reliable way to confirm correct orientation during reinstallation. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same drum belt installed in compatible Midea, Criterion, and Insignia electric and gas dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO Y312959 Dryer Drum Belt Replaces WPY312959 The XPARTCO Y312959 is an aftermarket replacement dryer drum drive belt compatible with a wide range of Maytag, Jenn-Air, Whirlpool, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryers — including the long-running vintage Maytag DE and DG halo-of-heat series. The drum belt is a critical component that connects the drive motor to the drum. It wraps all the way around the drum's circumference, passes around a spring-loaded idler (tension) pulley, and connects to the drive motor pulley. When the motor runs, it drives the belt, which rotates the drum to tumble clothes for even drying. Over time, drive belts fail from normal wear, cracking or fraying from age and repeated flexing, exposure to heat and lint buildup, stretching that causes slipping, or sudden breakage. Constructed from durable black rubber. Dimensions: 100" long x 3/8" (5/16") wide, with 5 ribs and 4 grooves. Includes instructions. It directly replaces Y312959, WPY312959, WPY312959VP, 312959, 3-12959, 3-14774, 314774, 1000H5, 8195-959, LB234, P46-150, P46-151, 1246110, 6-3129590, AP6024192, EAP11757542, PD00028571, and PS11757542. Important: install the belt with the grooved side against the motor pulley and the smooth side against the drum. Because the belt is symmetrical, it can be installed with either end facing out. Often replaced together with the idler pulley (WP6-3037050) and drum support roller kit (12001541 / 303373K), sold separately. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO Y312959 Dryer Drum Belt fixes Maytag, Jenn-Air, Whirlpool, Amana, and Kenmore dryers where the drum won't turn (motor runs but drum stays still), the drum spins slowly, or the dryer makes loud squealing/thumping noises. 100"L x 3/8"W. 5 ribs, 4 grooves. Black rubber. Replaces WPY312959, WPY312959VP, 312959, 3-12959, 3-14774, 314774, 1000H5, 8195-959, LB234, P46-150, P46-151, 1246110, 6-3129590, AP6024192, EAP11757542, PS11757542. Install grooved side against the motor pulley, smooth side against the drum. Often paired with idler pulley WP6-3037050 and drum roller kit 12001541. Common Problems This Part Fixes Dryer drum doesn't turn — motor runs but drum stays still (belt snapped) Dryer drum rotates slowly or intermittently — belt worn or slipping Loud squealing, squeaking, or thumping noises during operation — belt cracked, glazed, or misaligned Clothes taking much longer than normal to dry — drum not tumbling clothes effectively Visible cracks, fraying, or glazing on the belt surface Belt broken completely — often heard as a loud snap during operation Drum spins freely by hand with no resistance — a clear sign the belt has snapped Belt worn thin or stretched after decades of use on a vintage Maytag dryer Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer drum belt directly replaces the following OEM and cross-reference part numbers: Y312959, WPY312959, 1000H5, 1246110, 3-12959, 3-14774, 312959, 314774, 8195-959, P46-150, P46-151, 6 3129590, AP6024192, AWP51437, EAP11757542, PD00028571, PS11757542 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This dryer drum belt is compatible with select dryers from the following brands: Maytag electric dryers — DE106, DE107, DE110, DE180, DE18CA/CM/CS/CT, DE19CA/CD/CS/CT, DE210, DE212, DE21CA/CM/CS/CT, DE22CA/CS/CT, DE23CD, DE24CA/CM/CS/CT, DE25CS, DE26CA/CD/CS/CT, DE27CA/CS/CT, DE303, DE308, DE309, DE312, DE313, DE382, DE4000, DE408-DE9900 series and many more Maytag gas dryers — DG106, DG107, DG110, DG18CA/CM/CS/CT, DG19CA/CD/CS/CT, DG210, DG212, DG21CA/CM/CS/CT, DG22CA/CS and related DG-series models Maytag dryers — LDE and LDG series (LDE7304ACE, LDE8406ACE/ACM/ADE, LDE8410, LDG8424AAE, LDG9304AAM and related) Jenn-Air dryers (select models) Whirlpool dryers (select Whirlpool-built models) Amana, Magic Chef, Admiral, Norge, Roper dryers (select Whirlpool/Maytag-built models) Kenmore / Sears dryers (select Whirlpool/Maytag-built models) Note: When you replace the drum belt, this is also the ideal time to inspect the idler (tension) pulley (WP6-3037050) and the drum support rollers (kit 12001541 / 303373K) — they wear from the same friction cycles as the belt, and if they're rough, seized, or noisy, the new belt will wear out prematurely. Before replacing the belt due to noise, check the drum support rollers and idler pulley and replace if you see signs of wear. Always verify your dryer model number before ordering. Key Features Dryer drum drive belt — connects the motor pulley to the drum to enable tumbling during drying cycles Resolves "drum won't turn," "loud squealing noise," and "long dry times" symptoms when caused by belt failure Durable black rubber construction — engineered to withstand thousands of hours of high-temperature, high-friction operation Dimensions: 100" long x 3/8" (5/16") wide with 5 ribs and 4 grooves Install with the grooved side against the motor pulley and the smooth side against the drum Symmetrical design — can be installed with either end facing out Includes instructions Replaces WPY312959, WPY312959VP, 312959, 3-12959, 3-14774, 314774, 1000H5, 8195-959, LB234, P46-150, P46-151, 1246110, 6-3129590, AP6024192, EAP11757542, and PS11757542 Compatible with vintage Maytag DE/DG series, LDE/LDG series, plus Jenn-Air, Whirlpool, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryers Often replaced together with the idler pulley (WP6-3037050) and drum support roller kit (12001541 / 303373K), sold separately Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number Y312959 OEM Part Number WPY312959 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Dryers (Maytag / Whirlpool platform) Length 100" Width 3/8" (5/16") Ribs / Grooves 5 ribs / 4 grooves Color Black Material Rubber Installation Orientation Grooved side against motor pulley, smooth side against drum Often Paired With Idler Pulley (WP6-3037050), Drum Roller Kit (12001541 / 303373K) Compatible Brands Maytag, Jenn-Air, Whirlpool, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Wear Work Gloves — Grooved Side Against Motor Pulley Disconnect power at the breaker or outlet before beginning. Wear work gloves to protect your hands from sharp sheet metal edges inside the dryer cabinet. Access the drum by removing the appropriate panels — the specific procedure varies by model, but on many vintage Maytag dryers this involves removing the front or top panel. Photograph the belt routing before disassembly if any belt fragments remain. Remove any pieces of the old broken belt from around the drum, motor pulley, and idler pulley, and vacuum out accumulated lint and belt dust. Clean any belt dust off the drum. Route the new Y312959 belt around the drum. Install with the grooved (ribbed) side against the motor pulley and the smooth side against the drum — this is the correct orientation for proper drive engagement. Because the belt is symmetrical, either end can face outward. A helpful tip from experienced installers: use two small pieces of tape to hold the belt against the drum while you lace it onto the idler and motor pulleys. From under or behind the drum, route the belt around the idler (tension) pulley and the drive motor pulley following the belt diagram for your model. Rotate the drum by hand a few full turns to confirm the belt seats correctly and rides smoothly without binding. While you have the machine apart, check that the idler pulley and drum support rollers spin freely — if they're rough or noisy, replace them now to protect the new belt. Reassemble the panels, restore power, and run a test cycle. Tools needed: Phillips screwdriver, nut driver, socket/ratchet, vacuum, work gloves, tape (helpful for holding the belt). Frequently Asked Questions My dryer runs but the drum won't turn — is the belt the problem? Almost certainly, yes. When the motor runs (you hear the humming) but the drum stays still, the belt has almost always snapped. To confirm without opening the dryer: reach in and try turning the drum by hand. If it spins freely with no resistance whatsoever, the belt is broken. If it turns but feels notchy or resistant, the belt may still be intact but the drum rollers or bearings could be the issue. Opening the dryer to inspect is the definitive check — a snapped belt will be lying in the bottom of the cabinet. On decades-old Maytag dryers, a belt that finally snapped from age is one of the most common repairs. Which way does the belt go — grooves in or out? Install the belt with the grooved (ribbed) side facing the motor pulley and the smooth side against the drum. The ribs engage the grooved motor pulley for positive drive without slipping, while the smooth side rides against the large drum surface. Note that this is the opposite orientation from some other dryer belts (like certain Frigidaire belts where grooves face the drum) — so don't assume; follow the grooves-against-motor-pulley rule for this Maytag/Whirlpool-platform belt. The belt is symmetrical end-to-end, so either end can face outward; only the grooved-vs-smooth orientation matters. Should I replace the idler pulley and drum rollers at the same time? It's strongly recommended, especially on older dryers. The idler (tension) pulley (WP6-3037050) keeps the belt under proper tension, and the drum support rollers (kit 12001541 / 303373K) carry the drum's weight as it turns. All wear from the same friction and heat cycles as the belt. In fact, a common piece of repair advice is: before you replace the belt due to noise, check the drum support rollers and idler pulley first — worn rollers or a seized idler are frequent noise sources, and if you replace only the belt, the new belt may wear out prematurely against a bad pulley. Since the dryer is already apart, replacing all three together is efficient and saves a repeat repair. What's the difference between Y312959 and WPY312959? These are the same drum belt across production revisions. Y312959 was the earlier Maytag part number and WPY312959 is the Whirlpool-era part number (after Whirlpool acquired Maytag) for the same belt. WPY312959VP is a variant packaging code. All are physically and functionally identical — if your dryer's parts diagram shows any of these numbers, this listing is the correct replacement. The many other cross-references (3-12959, 314774, LB234, P46-150, etc.) reflect the belt's long production history across decades of Maytag dryers. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Maytag/Whirlpool OEM part, but is manufactured from durable rubber to match the dimensions (100"L x 3/8"W), rib and groove pattern (5 ribs, 4 grooves), and drive function of the original Y312959/WPY312959 drum belt used in compatible Maytag, Jenn-Air, Whirlpool, Amana, and Kenmore dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Choice Manufactured Parts Choice 40111201 Dryer Drum Belt Replaces WP40111201 Aftermarket 5-rib / 4-groove dryer drum belt for select Amana, Maytag, Whirlpool-built, Admiral, Crosley, Speed Queen, Magic Chef and related dryers. Product Overview The Choice 40111201 Dryer Drum Belt is an aftermarket replacement for Whirlpool/Maytag part WP40111201. The belt wraps around the dryer drum, motor pulley and idler pulley so the motor can rotate the drum during the drying cycle. A worn, stretched or broken belt can cause the dryer motor to run while the drum does not turn, or may contribute to thumping, slipping or abnormal belt noise. Quick Answer Choice part 40111201CM is a 5-rib, 4-groove belt approximately 93.5 inches long designed to replace WP40111201 / 40111201 on compatible Whirlpool-manufactured dryer platforms. Common Problems This Part May Fix Dryer runs but drum does not turn Drum turns intermittently or slips Broken or visibly cracked belt Stretched belt with poor tension Thumping or squealing related to belt wear Replaces and Cross-References WP40111201, 40111201, 14218936, 40051501, 40051502, 59174, AP6009126, AWP47792, EAP11742271, PD00002505, PS11742271, R0606549, WP40111201VP, 661570V, 661570, 3387610, 3389728, 3393999, 339728, 661570VP, AP5983729, PS11722115 Cross-reference numbers are provided for identification. This is a Choice Manufactured Parts aftermarket replacement and is not a Genuine Whirlpool OEM belt. Compatibility Designed for select dryers manufactured under Amana, Maytag, Whirlpool, Admiral, Crosley, Speed Queen, Magic Chef and related brands. Compatible model examples include: SDE405DAYW SDE305DAYW LGA30AW/PLGA30AW LE4807L/P1163706WL NG4819L53738 LEA20AL-PLEA20AL SLG332RAW LG3412L/P1122505WL LE2102L/P1118302WL Important: This is only a partial compatibility list. Verify the full dryer model number and original belt number before ordering. Similar-looking belts can differ in length, width and rib count. Key Features Choice Manufactured Parts aftermarket replacement Replaces WP40111201 / 40111201 5 ribs / 4 grooves Approx. 93.5-inch belt length Designed to restore proper drum rotation Fits many Whirlpool-manufactured dryer platforms Product Specifications Choice Part Number 40111201CM Listing Part Number 40111201 Brand Choice Manufactured Parts Part Type Dryer Drum Drive Belt Length Approx. 93.5 in. Ribs 5 Grooves 4 Material Reinforced rubber belt Condition New Part Quality Aftermarket Replacement Installation Notes Disconnect electrical power before servicing the dryer. Access the drum according to the appliance service procedure. Route the new belt around the drum with the ribbed side against the drum where specified by the dryer design. Route the belt around the motor pulley and idler/tension pulley exactly as the original belt was installed. Rotate the drum by hand before reassembly to confirm the belt tracks correctly and is not twisted. Inspect the idler pulley and drum rollers while the dryer is open; worn support parts can shorten belt life. Frequently Asked Questions Is this Genuine Whirlpool OEM? No. This is a Choice Manufactured Parts aftermarket replacement for WP40111201. How long is the belt? Choice specifies this belt at approximately 93.5 inches long with 5 ribs and 4 grooves. What does the dryer belt do? It connects the motor drive system to the drum so the drum tumbles while the dryer operates. Does it replace WP40111201? Yes. Choice 40111201CM is sold as an aftermarket replacement for WP40111201 and 40111201 on compatible models. Shop With Confidence Match the complete appliance model number and original belt number before ordering. Our compatibility team can help confirm fitment. Choice Replacement5-Rib Belt93.5 in. LengthCompatibility Support

Read more less

137292700 Dryer Genuine OEM Drum Belt The 137292700 is a genuine Frigidaire OEM multi-rib drum belt for Frigidaire stacked laundry center (combination washer/dryer) units, and also fits select Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and White Westinghouse combo models. This belt attaches to the motor pulley and spins the drum as the motor rotates, keeping clothes tumbling evenly throughout the drying cycle. Measures approximately 89-1/2" long and 1/4" wide, with multiple ribs. Over time, this belt naturally dries out, cracks, or breaks from regular use. If your dryer is running but the drum won't turn, there's a good chance the belt has broken. Symptoms of a failing belt include the drum not turning, loud banging noises, or the dryer failing to tumble clothes. It directly replaces 134163500, 134503900, 5303283287, 4PH 2273, 4PH2273, AFR14366, AH3408299, AP4565702, EA3408299, EAP3408299, PD00000115, PS3408299. Quick Answer The 137292700 Dryer Genuine OEM Drum Belt fixes Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and White Westinghouse stacked laundry center units where the drum won't turn, you hear loud banging noises, or the dryer won't tumble clothes. Approximately 89-1/2" long, 1/4" wide, multiple ribs. Replaces 134163500, 134503900, 5303283287, 4PH 2273, 4PH2273, AFR14366, AH3408299, AP4565702, EA3408299, EAP3408299, PD00000115, PS3408299. This is a laundry center (stacked combo) belt, distinct from standalone dryer belts — verify your full model number before ordering. Common Problems This Part Fixes Drum won't turn even though the motor is running Loud banging noises during operation Dryer failing to tumble clothes Belt visibly cracked, dried out, or broken Drum stopping mid-cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer drum belt directly replaces the following OEM and cross-reference part numbers: 134163500, 134503900, 5303283287, 4PH 2273, 4PH2273, AFR14366, AH3408299, AP4565702, EA3408299, EAP3408299, PD00000115, PS3408299 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select Frigidaire stacked laundry center units, and also fits select Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and White Westinghouse combo units built on the same platform, including model numbers such as WLXG42REW0, FLSE72GCTC, FLSG72GCT1, FLSG72GCT6, LCE852LL1, FLXG52RBS2, FLXG52RBS8, FLXE52RBS9, CLCG900FW0, CLCG900FW1, CLCG900FW2, CLCG900FW3, CLCE900FW0, CLCE900FW1, CLCE900FW2, CLCG500FW0, CLCG500FW1, CLCE600RW0, CLCE500MW1, CLCE500FW2, and CLCE500FW4. Note: This is a laundry center (stacked washer/dryer combo) belt, distinct from standalone Frigidaire dryer belts. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified multi-rib design Attaches to the motor pulley to spin the drum for laundry center (combo) units Resolves "drum won't turn," "loud banging noises," and "won't tumble" symptoms Approximately 89-1/2" long, 1/4" wide, multiple ribs Direct drop-in replacement matching the original length and profile Replaces 134163500, 134503900, 5303283287, 4PH 2273, 4PH2273, AFR14366, AH3408299, AP4565702, EA3408299, EAP3408299, PD00000115, PS3408299 Compatible with Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and White Westinghouse laundry center units Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 137292700 Part Type Laundry Center Multi-Rib Drum Belt Condition Genuine OEM Brand Frigidaire Application Stacked Washer/Dryer Laundry Centers Length Approx. 89-1/2" Width 1/4" Ribs Multiple Function Transmits motor rotation to spin the drum Repair Difficulty Moderate — laundry center disassembly required Quantity 1 drum belt Compatible Brands Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, White Westinghouse Installation Notes ⚠️ Unplug The Laundry Center Before Starting Disconnect power to the laundry center unit at the outlet before beginning. Wear work gloves. This repair is best approached from the top down: remove the top of the unit first, which gives more room to get the dryer tub out. Remove the two screws from the vented plate on the back of the machine to access and undo the old belt. Since this is a stackable washer/dryer combo, also remove the white plate on the front between the washer and dryer sections for full access. Locate the old belt connecting the motor pulley to the drum and remove it. Fit the new 137292700 belt around the drum and motor pulley in the same path as the old one, making sure it seats correctly and is properly tensioned. Reassemble the front plate, vented back plate, and top of the unit. Restore power and run a test cycle to confirm the drum tumbles smoothly with no banging or unusual noise. Tools needed: putty knife, screwdriver set, work gloves. Frequently Asked Questions The motor is running but the drum won't turn. Is this the belt I need? Yes, this is the classic and most reliable sign of a broken drum belt. If you can hear the motor running normally but the drum itself stays still, the belt has likely dried out and broken, no longer connecting the motor's rotation to the drum. Is this the same as a standalone Frigidaire dryer belt? No, this belt is specifically sized and profiled for Frigidaire-style stacked laundry center units, where the washer and dryer are combined into one appliance. It's a different part from standalone Frigidaire dryer belts used on separate dryers. Confirm your unit type and model number before ordering. Is this a difficult repair? It's a moderate repair since it involves removing the top of the laundry center unit, the vented back plate, and the front plate between the washer and dryer sections to get full access to the belt. One customer described working from the top down as the easiest approach, since it gives more room to remove the dryer tub. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original length, width, and rib pattern of the multi-rib drum belt originally installed in your laundry center. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

(6 Pack) XPARTCO 40111201 Dryer Drum Belt – Replaces WP40111201 – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Restore smooth drum rotation and dependable drying performance with the XPARTCO 40111201 Dryer Drum Belt. This high-quality replacement transfers power from the motor to the dryer drum, allowing consistent tumbling during drying cycles. A worn, stretched, or broken belt can cause the drum to stop turning, produce squealing noises, or prevent the dryer from completing cycles. Replacing it with this durable XPARTCO belt ensures reliable operation and efficient drying. Replaces Part Numbers WP40111201, 40111201, 14218936, 40051501, 40051502, 59174, PD00002505, EAP11742271, AP6009126, PS11742271, R0606549, WP40111201VP, 661570V, 661570, 3387610, 3389728, 3393999, 339728, 661570VP, PD00023608, AP5983729, PS11722115. Compatibility This replacement dryer drum belt fits select Whirlpool, Maytag, Kenmore, Amana, Estate, Roper, and Crosley dryers. Example compatible models include (but are not limited to):Whirlpool WED4815EW1, WED5000DW2Maytag MEDC215EW1Kenmore 110.65132411 Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM belt size, rib count, and tension 🌀 Restores Drum Rotation – Ensures smooth, consistent tumbling 💪 Reinforced Rubber Construction – Designed to resist stretching and wear 💰 Cost-Effective Repair – Reliable performance without OEM pricing 🛡️ Fixes Common Issues – Solves drum not turning, squealing noises, or belt slippage 📐 Product Specification Part Number: 40111201 Component Type: Dryer Drum Belt Material: Reinforced rubber Belt Style: Multi-rib (OEM-equivalent) 4 Rib, 93.5" Application: Motor-to-drum drive system Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to prevent electrical shock. Steps: Disconnect dryer power and open the cabinet. Remove the drum to access the belt path. Remove the worn belt from the motor and idler pulley. Install the new XPARTCO 40111201 belt following the original routing. Reinstall the drum, reassemble panels, and restore power. Run a test cycle to confirm proper operation. ⏱️ Time Required: 30–45 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore smooth dryer operation — Add to Cart Now for a dependable, budget-friendly repair!

Read more less