Search results for "dryer heater"

XPARTCO XP6974 Dryer Thermostat Kit Replaces WP3387134, WP3392519, W10900067, 279816 The XPARTCO XP6974 is an aftermarket dryer thermostat kit containing four thermal components for Whirlpool-family electric and gas dryers including Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef. The kit includes the cycling thermostat (WP3387134), thermal fuse (WP3392519), high-limit thermostat and thermal cut-off kit (279816 / W10900067) — the complete set of heat-sensing and safety components that regulate dryer temperature and prevent dangerous overheating. These four components work together to control and protect the dryer's heating system. When any one of them fails, the dryer may produce no heat, overheat, run too long, or stop mid-cycle. Because a failed thermal fuse is almost always caused by an underlying overheating condition that also stresses the other components, replacing all four together in a single repair is the recommended approach. Includes all wiring hardware needed for installation. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO XP6974 Dryer Thermostat Kit fixes Whirlpool-family dryers that produce no heat, overheat, take too long to dry, or stop mid-cycle. Includes all four thermal components: cycling thermostat (L155-25), thermal fuse (196°F), high-limit thermostat (L250-80), and thermal cut-off (309°F). Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef electric and gas dryers. Common Problems This Kit Fixes Dryer produces no heat — thermal fuse or high-limit thermostat has blown Dryer takes multiple cycles or very long time to dry clothes Dryer overheats — clothes or drum too hot to touch after a cycle Dryer shuts off mid-cycle and will not restart Dryer tumbles normally but generates no heat at all Dryer runs too long because cycling thermostat is not regulating temperature Repeated thermal fuse failures — underlying thermostat fault causing recurring overheating What's in the Kit Part 1 of 4 WP3387134 Cycling Thermostat Rated L155-25 · Monitors drum air temperature and cycles the heating element on and off to maintain the set drying temperature · Located on the exhaust duct or blower housing · Should show closed continuity at room temperature Part 2 of 4 WP3392519 Thermal Fuse Opens at 196°F (91°C) · One-time safety device located on the exhaust duct · Permanently interrupts power to the heating element if the dryer overheats · Cannot be reset — must be replaced if blown · Most common cause of no-heat in Whirlpool-family dryers Part 3 of 4 High-Limit Thermostat (279816 / W10900067) Rated L250-80 · Mounted on the heating element housing · Opens at approximately 250°F to cut power to the heating element if temperature exceeds safe limits · Resets automatically when it cools · Should show closed continuity at room temperature Part 4 of 4 Thermal Cut-Off Fuse (3977393 / 279816 kit) Opens at 309°F · Backup one-time safety device on the heating element housing · Permanently interrupts power to the heating element if the high-limit thermostat fails to open · Cannot be reset — must be replaced if blown Replaces Part Numbers WP3387134 Cycling Thermostat cross-references: WP3387134, WP3387134VP, 3387134, 3387135, 3387139, 306910, 3-6910, ET187, AP6008270, PS11741405 WP3392519 Thermal Fuse cross-references: WP3392519, WP3392519VP, 3392519, 3388651, 694511, 80005, ET401, G4AP0500, AP6008325, PS11741460 279816 High-Limit Thermostat and Thermal Cut-Off Kit cross-references: 279816, 279816VP, W10900067, 3977393, 3977767, WP3977767, WP3977767VP, 3399848, 3399693, 2651, AP3094244, AH334299, EA334299, EAP334299, PS334299 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat kit is compatible with select gas and electric dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (Whirlpool-built models) Maytag dryers (gas and electric) Amana dryers KitchenAid dryers Roper dryers Admiral dryers Estate dryers Crosley dryers Inglis dryers Magic Chef dryers Important: If your thermal fuse has blown, always check for the root cause before replacing — a clogged exhaust vent is the most common cause of dryer overheating. Clean the full length of the exhaust duct before or after this repair. If the vent is clear, a failed cycling thermostat or high-limit thermostat is likely the root cause. Key Features Complete 4-part thermal kit — covers the cycling thermostat, thermal fuse, high-limit thermostat, and thermal cut-off in a single repair Cycling thermostat (L155-25) — regulates drum temperature to maintain consistent, efficient drying Thermal fuse (196°F) — one-time safety device that permanently interrupts heat if the dryer overheats High-limit thermostat (L250-80, ~250°F) — cuts power to the heating element when temperature exceeds safe limits; auto-resets Thermal cut-off (309°F) — backup one-time safety device protecting against heating element runaway Replacing all four parts together ensures the complete thermal circuit is renewed — prevents recurrence if a failing thermostat caused the fuse to blow Includes all wiring hardware for installation Compatible with 11 major appliance brands on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Kit Part Number XP6974 Condition Aftermarket Replacement Application Gas and Electric Dryers Kit Includes 1x WP3387134 Cycling Thermostat, 1x WP3392519 Thermal Fuse, 1x High-Limit Thermostat (L250-80), 1x Thermal Cut-Off Fuse (309°F), wiring hardware Cycling Thermostat Rating L155-25 (closes at 155°F, opens at 25°F differential) Thermal Fuse Trip Temp 196°F (91°C) — one-time, non-resettable High-Limit Thermostat Rating L250-80 (opens at ~250°F) — auto-resets Thermal Cut-Off Trip Temp 309°F — one-time, non-resettable Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef Installation Notes ⚠️ Unplug Dryer and Shut Off Gas Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the back panel of the dryer to access the heating element housing and exhaust duct. The thermal fuse (WP3392519) and cycling thermostat (WP3387134) are located on the exhaust duct or blower housing — disconnect the wires, unscrew the mounting screws, and install the new parts in the same positions. The high-limit thermostat and thermal cut-off (279816 kit) are located on the heating element housing — disconnect the wires and unscrew the mounting screws to remove the old parts and install the new ones. Reconnect all wires to the correct terminals — take a photo before disconnecting to reference during reinstallation. Reassemble the back panel, restore power, and run a test cycle to verify heat. Tip: Before running the dryer, also clean the full length of the exhaust duct — a clogged vent is the most common root cause of dryer overheating and repeated thermal fuse failures. Tools needed: Phillips screwdriver, 1/4" nut driver, needle-nose pliers. Frequently Asked Questions What does each part in this kit do? The cycling thermostat (WP3387134) monitors the air temperature in the exhaust duct and cycles the heating element on and off to maintain the correct drying temperature — it is the part that controls how hot the dryer gets during normal operation. The thermal fuse (WP3392519) is a one-time safety device that permanently cuts power to the heating element if the dryer overheats above 196°F — it is the most common cause of no-heat in Whirlpool-family dryers. The high-limit thermostat opens at approximately 250°F to cut heating element power if temperature gets too high, and resets automatically when it cools. The thermal cut-off is a backup one-time fuse on the heating element that opens at 309°F if the high-limit thermostat fails to protect the heater. Why should I replace all four parts instead of just the one that failed? When a thermal fuse blows, it almost always blew because the dryer overheated — and that overheating event put significant stress on all the other thermal components as well. A failing cycling thermostat is the most common cause of repeated thermal fuse failures: if the cycling thermostat stops regulating temperature correctly, the dryer runs too hot, the high-limit thermostat is repeatedly stressed, and the thermal fuse eventually blows. Replacing just the fuse without replacing the cycling thermostat means the same overheating will blow the new fuse. Replacing all four parts at once eliminates that risk in a single repair. How do I test these parts with a multimeter? Set the multimeter to continuity or resistance mode. The thermal fuse (WP3392519), cycling thermostat (WP3387134), and high-limit thermostat should all show closed continuity (near-zero resistance) at room temperature. The thermal cut-off should also show closed continuity at room temperature. Any part that reads open (no continuity / infinite resistance) at room temperature has failed and needs to be replaced. A blown thermal fuse or cut-off will always read open — they are one-time devices and cannot reset. What causes the thermal fuse to blow repeatedly? The most common cause by far is a clogged exhaust vent — lint accumulation inside the dryer duct restricts airflow, causing heat to build up inside the dryer cabinet until the thermal fuse trips. Always clean the full length of the exhaust duct before and after replacing these parts. Other causes include a failing cycling thermostat that is not regulating temperature correctly, a stuck heating element relay, or a dryer placed in an enclosed space without adequate ventilation. Is this kit compatible with both electric and gas dryers? Yes — the XP6974 kit is compatible with both electric and gas Whirlpool-family dryers. Both types use the same cycling thermostat (WP3387134) and thermal fuse (WP3392519). The high-limit thermostat and thermal cut-off (279816 kit) are located on the heating element in electric models and on the burner assembly area in gas models. Always verify your specific model number before ordering to confirm all four parts apply to your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 279769 Dryer Thermostat Kit The XPARTCO 279769 is an aftermarket replacement thermal cut-off and high-limit thermostat kit for Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers. This kit bundles two components that guard against overheating at different thresholds: the 3390291 high-limit thermostat (rated L250-80F) monitors internal temperature and interrupts power at approximately 250°F to prevent overheating, then resets itself automatically once the dryer cools — no replacement needed after each trip. The 3977394 thermal cut-off fuse is the backup: rated at 352°F, it's a one-time safety device that permanently opens the circuit if temperatures climb high enough that the thermostat alone didn't prevent an overheat. These two parts are sold together and should be replaced together as a set, since they protect the same circuit and tend to be stressed by the same underlying problem. Whirlpool's own guidance is direct: when the thermal cut-off fails, it usually indicates a venting problem, and failing to correct that airflow issue will cause repetitive failures even with new parts installed. Symptoms include the dryer not heating, clothes coming out extremely hot, or the dryer not running at all. This kit is commonly used alongside heating element 4391960. It directly replaces 279769, 279548, 2796769, 279769VP, 2821, 2004, 3387812, 3389946, 3398671, 3977394, 695563, 80001, SET184, SET198, TJSET198, ET184, AP3094224, AH334278, EA334278, EAP334278, PD00002485, PS334278, WP3390291, AP6008306, 3390291, 696397, and PS11741441. As an aftermarket replacement, the 279769 kit is built to OEM-equivalent quality standards. Quick Answer The XPARTCO 279769 Dryer Thermostat Kit fixes Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers with no heat, no power at all, or clothes coming out dangerously hot. Includes the 3390291 high-limit thermostat (250°F, auto-resetting) and the 3977394 thermal cut-off fuse (352°F, one-time). Replaces 279548, 2796769, 279769VP, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AP3094224, PS334278, WP3390291, AP6008306, 3390291, 696397, PS11741441. Always inspect and clean the exhaust venting when replacing this kit — a blown thermal fuse is a symptom of restricted airflow, and skipping the vent check leads to repeat failures. What's In The Kit Component Rating Function 3390291 High-Limit Thermostat L250-80F (~250°F) Interrupts power to prevent overheating, resets automatically once the dryer cools. 3977394 Thermal Cut-Off Fuse 352°F One-time backup safety device — permanently opens the circuit if temperature exceeds safe limits. Cannot reset. Common Problems This Kit Fixes Dryer won't start at all — no lights, no tumble, no response Dryer runs but produces no heat Clothes coming out extremely hot, hot enough to be uncomfortable to handle Dryer that stopped working suddenly after running unusually hot Repeated thermal cut-off failures on a dryer with a known venting issue Dryer that shuts off prematurely mid-cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermostat kit directly replaces the following OEM and cross-reference part numbers: 279769, 2004, 279548, 2796769, 279769VP, 2821, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AH334278, EA334278, AP3094224, OEM9282681, SET184, SET198E, AP334278, L250-80F, PS334278, AWP39149, PD00002485. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat kit is compatible with select Whirlpool electric dryers, and also fits select Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral dryers built on the Whirlpool platform, including model numbers such as: 7MWET4027HW0 WET3300XQ0 WET4027EW0, WET4027EW1 WET4027HW0, WET4027HW1, WET4027HW2 WETLV27FW0, WETLV27HW0, WETLV27HW1, WETLV27HW2, WETLV27HW3 YWET4027EW1, YWET4027HW0, YWET4027HW1, YWET4027HW2 Note: This kit was used on Whirlpool-built electric dryers primarily from 1985 to 1995. Always verify your full model number before ordering, since Whirlpool used several different thermostat and fuse designs across its dryer lineup over the years. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement built to match Whirlpool's factory-specified thresholds for both components 2-piece kit: 3390291 high-limit thermostat (250°F, auto-resetting) and 3977394 thermal cut-off fuse (352°F, one-time) Resolves "no heat," "no power at all," and "clothes coming out extremely hot" symptoms Addresses two overheat-protection thresholds in the same circuit at once Commonly used alongside heating element 4391960 Direct drop-in replacement for both original components Replaces 279548, 2796769, 279769VP, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AP3094224, PS334278, WP3390291, AP6008306, 3390291, 696397, and PS11741441 Compatible with Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Kit Part Number 279769 Kit Contents 1x High-Limit Thermostat (3390291), 1x Thermal Cut-Off Fuse (3977394) OEM Part Number 279769 Condition Aftermarket Replacement Brand Whirlpool High-Limit Thermostat Rating L250-80F (~250°F, auto-resetting) Thermal Fuse Rating 352°F (one-time, non-resettable) Companion Heating Element 4391960 (commonly used together) Repair Difficulty Easy to Moderate — basic tools required Compatible Brands Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, Admiral Installation Notes ⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel, near the heating element and blower housing where both components are mounted. Photograph the wiring connections before disconnecting anything, since the thermostat and fuse can be easy to swap positions by mistake. Remove each old component from its mounting position, noting orientation, and disconnect its wiring. Before reassembling, fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. When the thermal cut-off fails, it usually indicates a venting problem, and failing to correct that airflow issue will cause repetitive failures even with these new parts installed. Install the new 3390291 thermostat and 3977394 thermal fuse from this kit in the same positions as the parts they replace, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), work gloves. Frequently Asked Questions My clothes are coming out extremely hot, hot enough to burn my hands. Is this the right kit? Yes, this is a documented symptom this kit addresses. If the high-limit thermostat fails to regulate temperature correctly, the dryer can run far hotter than it should, producing dangerously hot clothing at the end of a cycle. Whirlpool's own parts support has specifically pointed customers with this exact complaint toward this kit. Stop using the dryer if you notice this symptom and replace both components promptly. Why do I need to replace both the thermostat and the fuse together? These two parts protect the same circuit at different thresholds and tend to fail from the same underlying cause. If the high-limit thermostat isn't regulating temperature correctly, the thermal fuse often ends up blowing as the backup safety measure. Replacing only one risks the other failing again shortly after, so they're sold and serviced together as a set. I replaced this kit and the dryer failed again. What should I check? This is a strong sign the underlying cause — almost always restricted airflow — was never addressed. Thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. Failing to correct a venting issue will cause repetitive failures of this kit even when it's brand new. Should I replace the heating element at the same time? It's worth considering if your dryer's heating element (commonly 4391960 on compatible models) is original and has been running alongside a failing thermostat, since sustained overheating can stress the element as well. It's not required, but since you'll already have the panel open for this repair, it's a reasonable time to inspect the element for visible damage. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the temperature thresholds and mounting configuration of the original 279769 high-limit thermostat and thermal cut-off fuse kit used in compatible Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10169881 Dryer Genuine OEM Thermostat Kit Description: This Dryer thermostat kit is an OEM replacement part responsible for ensuring the safety and temperature regulation of the dryer. The high-limit thermostat serves as a critical safety device that monitors and regulates the temperature inside the dryer. When the temperature rises to a level beyond the safe operating range, the high-limit thermostat interrupts the flow of electricity to the heating element. The thermal cut-out fuse, included in this kit, offers an additional layer of protection by disconnecting power to the heating element if it detects excessively high temperatures. Replaces Part Numbers: W10169881, 1455409, AH1964653, EA1964653, AP4316800, PS1964653.    California Residents only WARNING: California’s Proposition 65

Read more less

XPARTCO AGM30045804 Dryer Thermostat Kit The XPARTCO AGM30045804 is an aftermarket replacement high-limit thermostat and thermistor kit for LG dryers. These two components work together in the same temperature-regulation circuit: the thermistor is a temperature sensor, mounted in the blower housing with its wire harness included, that continuously reports drum temperature to the control board so it can fine-tune heat output throughout the cycle. The high-limit thermostat is a safety switch that automatically shuts off the heating element if temperatures climb past a safe threshold, then resets itself once the dryer cools, without needing to be replaced the way a thermal fuse does. Because these two parts share the same circuit and tend to wear or fail around a similar timeline, LG sells and services them together as one kit rather than as separate individual parts. Symptoms of failure in this circuit include the dryer overheating (which can scorch clothing or, left unaddressed, pose a fire risk), the dryer running with little or no heat, drying times that have become inconsistent, an error code related to temperature control on the display, or clothes coming out damp after a full cycle. It directly replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, and PS16732335. As an aftermarket replacement, the AGM30045804 kit is built to OEM-equivalent quality standards. Quick Answer The XPARTCO AGM30045804 Dryer Thermostat Kit fixes LG (and select Kenmore, GE-branded LG-built) dryers with overheating, little or no heat, inconsistent drying times, a temperature-related error code, or clothes coming out damp after a full cycle. High-limit thermostat + thermistor with wire harness. Replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, PS16732335. If you've already replaced the high-limit thermostat alone and the problem returns, this combined kit — which also addresses the thermistor — is the next step. What's In The Kit Component Function High-Limit Thermostat Automatically shuts off the heating element if temperature exceeds safe limits, then resets itself once the dryer cools. Thermistor (with wire harness) Continuously senses drum/blower housing temperature and reports it to the control board to regulate heat output throughout the cycle. Common Problems This Kit Fixes Dryer overheating, sometimes scorching or damaging clothing Dryer running with little or no heat Inconsistent drying times — cycle shuts off too early or runs longer than necessary Temperature-related error code displayed on the control panel Clothes remaining damp after a full drying cycle High-limit thermostat that keeps tripping repeatedly Dryer that has already had its high-limit thermostat replaced once but the problem returned Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermistor and thermostat kit directly replaces the following OEM and cross-reference part numbers: AGM30045804, 6931EL3003C, 6931EL3004B, 6931EL3002B, 6931EL3003F, 6931EL3003G, 6323EL2001B, ALG53406, AP7206815, EAP16732335, PD00079467, PS16732335, AGM75510744, EAP16746326, PD00083166, ALG53211, AP7195784, PS16746326. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This kit is compatible with select LG dryers, and also fits select Kenmore and GE-branded dryers built on the LG platform. Note: A specific verified model list was not consistently available across sources at the time this page was built. Some parts diagrams reference additional related thermostat components (such as a separate blower thermostat) beyond what's included in this kit — if your repair involves more than a high-limit thermostat and thermistor, or if you're unsure exactly what's failed on your model, contact our support team with your model number and we'll help confirm which parts you need before you order. Key Features Aftermarket replacement built to match LG's factory-specified resistance values and switch thresholds Combined kit addresses the high-limit thermostat and thermistor together, since both share the same temperature-regulation circuit Resolves "overheating," "little or no heat," "inconsistent drying," and "damp clothes after a full cycle" symptoms Thermistor ships with its wire harness included High-limit thermostat resets automatically after tripping — no replacement needed after each trip Direct drop-in replacement for both original components Replaces 6931EL3003C, 6323EL2001B, 6931EL3003F, 6931EL3004B, AP7206815, EAP16732335, and PS16732335 Compatible with LG and select Kenmore and GE-branded LG-built dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number AGM30045804 Part Type Dryer High-Limit Thermostat and Thermistor Kit OEM Part Number AGM30045804 Condition Aftermarket Replacement Brand LG Kit Contents High-limit thermostat + thermistor with wire harness Thermistor Location Blower housing High-Limit Thermostat Type Automatically resetting Repair Difficulty Easy to Moderate — 30 to 60 minutes Compatible Brands LG, select Kenmore, GE (LG-built models) Installation Notes ⚠️ Unplug Dryer Before Starting — Let It Cool Fully First Disconnect power at the outlet or shut off the circuit breaker before beginning, and allow the dryer to cool completely if it was recently run. Wear work gloves. Access on many LG models follows this general sequence: remove the lint screen, then remove the two front panel screws underneath it, the two screws on the face of the panel, and the two screws holding the blower cover in place. Disconnect the door switch connector and remove the front panel. With the front open, release the drive belt from the tensioner and remove the drum to access the blower housing where the thermistor is located. Photograph the wiring connections before disconnecting anything, since the thermistor and high-limit thermostat can be easy to confuse with other similar-looking components nearby. Disconnect and remove the old thermistor and high-limit thermostat, noting their exact mounting positions. Install the new components from this kit in the same positions, reconnecting wiring exactly as photographed. Reinstall the drum, re-tension the belt over the tensioner, and reassemble the front panel, blower cover, and lint screen area in reverse order. Restore power and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions I already replaced the high-limit thermostat, but it keeps tripping. Why would I need this kit instead? This is a well-documented pattern. If the thermistor — the sensor that reports temperature to the control board — is misreading heat, the control can keep driving the heating element past the point where the high-limit thermostat has to trip repeatedly to protect the dryer, even with a brand-new thermostat installed. Replacing the thermistor alongside the thermostat addresses the root cause rather than just the symptom, which is exactly why LG packages them together as one kit. What's the difference between the thermistor and the high-limit thermostat? The thermistor is a sensor, not a switch — it's a variable resistor whose resistance changes with temperature, and the control board reads that value continuously to regulate heat output throughout the cycle. The high-limit thermostat is a safety switch that does one job: it shuts off the heating element automatically if temperature exceeds a safe limit, then resets itself once things cool down. A failing thermistor causes inconsistent or inaccurate heat regulation; a failing high-limit thermostat causes the dryer to shut off unexpectedly or fail to protect against overheating. My parts diagram shows more thermostat-like parts than what's in this kit. Did I order the wrong thing? Not necessarily — some LG dryer models have additional related components, such as a separate blower thermostat, that are not part of this specific kit. This kit covers the high-limit thermostat and thermistor. If your repair calls for additional related parts, or if you're not sure exactly which components your model needs, contact our support team with your model number and we'll help you confirm the complete parts list before you order. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the resistance values, switch threshold, and wire harness configuration of the original AGM30045804 high-limit thermostat and thermistor kit used in compatible LG, Kenmore, and GE-branded LG-built dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3387134 - 3392519 Dryer Cycling Thermostat and Thermal Fuse Set - Compatible with Whirlpool, Kenmore, Maytag Product Description Maintain safe and efficient dryer operation with the XPARTCO 3387134 - 3392519 Dryer Cycling Thermostat and Thermal Fuse Set. This replacement kit includes one cycling thermostat (3387134, L155-25) and one thermal fuse (3392519), designed as a replacement for select Whirlpool, Kenmore, Maytag, and other compatible dryers. The cycling thermostat regulates drum temperature, while the thermal fuse prevents overheating by cutting power if temperatures exceed safe limits. This set addresses issues like overheating, insufficient heat, no heat, or prolonged drying times. Test the thermal fuse first if the dryer won't heat, as it typically fails before the thermostat. Note: Includes (1) cycling thermostat and (1) thermal fuse. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: Cycling Thermostat: WP3387134, 3387134, 3387135, 3387139, 3-6910, 306910, 326801, 661512, L150-15F, L155-25F, AP6008270, PS11741405. Thermal Fuse: 3392519, WP3392519, 3388651, WE4X857, G4AP0500, 6L4101091C, ET401, 3388651, 694511, 80005, PS11741460, AP6008325. Compatibility: Compatible with select dryer models, including but not limited to: Whirlpool: LE5700XKW0, LE5920XKW0, WED4815EW1, WED4910XQ1, WED5300SQ0 Kenmore: 110.97591420, 110.97591220, 110.97592420, 110.60072990 Maytag: MDE5500AYW, MDE6000AYW, MDE7600AYW Roper: RED4440VQ1, REX5634KQ1 Amana: NED4655EW0 KitchenAid: KEYE760WWH0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Amana, KitchenAid, and other dryers. 🔧 Specifications: Replacement kit with one cycling thermostat (L155-25 SPST, 120V, 2W) and one thermal fuse (250°F limit, non-resettable). 💪 Reliable Performance: Regulates drum temperature and prevents overheating for safe, efficient drying. 🛠️ Easy Installation: Requires a screwdriver and pliers; typically installed in 15–30 minutes. 🛡️ Effective Fixes: Resolves overheating, insufficient heat, no heat, or prolonged drying times. Product Specification Part Number: XPARTCO 3387134 - 3392519 Component Type: Dryer cycling thermostat and thermal fuse kit Material: Plastic and metal Electrical Specs: Cycling Thermostat: 120V, 2W; L155-25 SPST, opens at 155°F, closes at 130°F  Thermal Fuse: 250°F limit, 125/250V, non-resettable Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running safely and efficiently today! Add to cart now for a reliable fix!

Read more less

Genuine OEM Dryer Part W11683629 Dryer Genuine OEM Thermistor A manufacturer-approved temperature-sensing component designed to help the dryer control system regulate heat and drying performance. Product Description The W11683629 Dryer Genuine OEM Thermistor monitors air temperature inside the dryer and sends temperature information to the electronic control system. The control uses this signal to cycle the heat source and maintain the correct operating temperature during the drying cycle. This is a Genuine OEM replacement part manufactured to the original equipment specifications for fit, electrical response, and dependable operation. Replacing a failed thermistor can help restore accurate temperature control, normal cycle times, and consistent drying results. Quick Answer W11683629 is a Genuine OEM dryer thermistor. It senses dryer air temperature and communicates with the control board so the appliance can regulate heating. Replace it when testing or diagnosis confirms an open, shorted, damaged, or inaccurate temperature sensor. Common Problems This Part Fixes Dryer overheats or runs hotter than normal Clothes remain damp after a complete cycle Drying cycles take too long Heat cycles on and off incorrectly Dryer stops before clothes are dry Temperature-sensor or heating-related error codes Replaces Part Number The product title identifies the following part number: W11683629, W11452857, AP7216892, AWP1400864, PS17216463.  No additional replacement or cross-reference number was included in the supplied product title. Compatibility Designed for select dryer models that specify Genuine OEM part number W11683629. Appliance parts can look similar while using different resistance ranges, connectors, mounting positions, or control logic. Always verify the complete dryer model number and the required part number before ordering. The model-number label is commonly located around the door opening, on the cabinet frame, or on the rear identification plate. Key Features Genuine OEM manufacturer-approved component Monitors dryer operating temperature Sends temperature feedback to the control system Helps regulate heating and cycle performance Built to original fit and electrical specifications Direct replacement when W11683629 is specified Product Specifications Part Number W11683629 Part Type Dryer Thermistor / Temperature Sensor Condition New Quality Genuine OEM Application Clothes Dryer Primary Function Measures air temperature for the dryer control system Package Quantity 1 Thermistor Troubleshooting Guide Disconnect the dryer from electrical power before opening or servicing the cabinet. Inspect the exhaust vent, lint path, and blower area. Restricted airflow can produce symptoms similar to a failed thermistor. Inspect the thermistor body, terminals, connector, and wire harness for damage, corrosion, loose connections, or heat discoloration. Disconnect the thermistor and test resistance with a multimeter. Compare the reading with the dryer service information for the measured temperature. Warm or cool the sensor carefully. Resistance should change smoothly as temperature changes; an open circuit, short circuit, or unstable reading can indicate failure. Check the heater circuit, thermal devices, moisture-sensing system, and control board when the thermistor tests within specification. Safety: Do not bypass a thermistor or protective temperature device. Installation and diagnosis should be performed by a qualified person when you are not comfortable servicing electrical appliances. When Should You Replace This Part? The thermistor is open, shorted, or outside the specified resistance range The sensor reading does not change correctly with temperature The housing or connector is cracked, burned, or physically damaged A service diagnostic identifies W11683629 as the failed component Airflow and related heating components have been checked and the thermistor fails testing Shop With Confidence Purchase the correct Genuine OEM replacement part for dependable fit and performance. Verify your dryer model number before ordering, and contact our parts team when compatibility assistance is needed. Genuine OEM Fast U.S. Shipping Compatibility Support Secure Checkout  

Read more less

XPARTCO 6931EL3001E Dryer Thermostat – Compatible with LG and Kenmore Dryers Product Description Maintain proper dryer safety and temperature control with the 6931EL3001E Dryer Thermostat. This replacement part monitors and regulates dryer temperature to prevent overheating and ensure efficient drying cycles. A faulty thermostat may cause your dryer to stop heating, overheat, or shut off unexpectedly. Replacing it restores reliable performance and helps extend the life of your dryer. Replaces Part Numbers 6931EL3001E, 1268363, 6931EL3001B, 6931EL3001C, AH3530481, EA3530481, PD00023869, EAP3530481, AP4440977, PS3530481, L125-31C, 503475. Compatibility This dryer thermostat is compatible with select LG and Kenmore dryer models. Example compatible models include (but are not limited to): LG DLE2516W, DLE7177WM, and Kenmore 796.80272900. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Broad Compatibility – Fits select LG and Kenmore dryers 🔒 Reliable Safety – Prevents overheating by regulating dryer temperature 💰 Cost-Effective Replacement – OEM-equivalent performance at a lower price 🛠️ DIY-Friendly – Quick installation with basic tools 🛡️ Fixes Common Issues – Restores heating, prevents overheating, and fixes dryer shutdown problems 📐 Product Specification Part Number: XP6931EL3001E Component Type: Dryer Thermostat Material: High-heat resistant metal and thermal components Mounting: Direct replacement, mounts on heating element housing Operating Conditions: Designed for residential dryers Compliance: OEM-equivalent performance and safety standards 🛠️ Installation Notes Tools Needed: Phillips screwdriver, flathead screwdriver, needle-nose pliers ⚠️ Safety First: Always disconnect power before starting repairs to avoid electrical shock. Steps: Unplug dryer and remove back access panel. Locate thermostat on heating element housing. Disconnect wire terminals from the old thermostat. Remove screws holding it in place and replace with the new thermostat. Reconnect wires, secure the component, and reinstall the access panel. Restore power and test dryer operation. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore your dryer’s safe operation today — Add to Cart Now for fast, budget-friendly repair!

Read more less

3204267 Dryer Genuine High-Limit Thermostat Replaces Part Numbers: 3204267, 145160, 508516, 73204267, AH446428, EA446428, OEM8525910, AP2131477, PS446428, WE4X757, WE04X0757, WE04X10002, WE4X10002, AH268202, EA268202, OEM8171210, AP2042802, PS268202. Description: This High Limit Thermostat is a Genuine part for specific Frigidaire, GE dryer models. It serves as a critical safety device, designed to cut off the power to the heating element if the dryer overheats. This thermostat helps prevent potential fire hazards by maintaining a safe operating temperature within the dryer. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO WR51X10055 Refrigerator Defrost Heater Assembly The XPARTCO WR51X10055 is an aftermarket replacement refrigerator defrost heater and bracket assembly compatible with a wide range of GE, Hotpoint, Kenmore, Haier, Americana, Monogram, and Café refrigerators. The defrost heater is a glass quartz tube heater mounted on a bracket below the evaporator coils in the freezer compartment. During each automatic defrost cycle, the heater energizes and melts any frost that has accumulated on the evaporator coils — maintaining unobstructed airflow through the coils so the refrigerator can cool efficiently. When the heater fails, frost accumulates on the coils unchecked, blocking airflow and causing both the freezer and fresh food sections to gradually warm up. Rated at 120V, 725W, this single quartz tube heater assembly measures 12-1/8" L x 3-3/8" W x 2-1/8" H and includes the heater element and mounting bracket. It directly replaces WR51X10030, AP3183311, 914088, AH303781, EA303781, PS303781, SH323, and EAP303781. Often replaced together with the defrost thermostat (WR50X10068) and temperature sensor (WR55X10025) for a complete defrost system repair. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO WR51X10055 Refrigerator Defrost Heater Assembly fixes GE and Hotpoint refrigerators where frost is building up on the evaporator coils, the freezer is too warm, the fresh food section is warming up, or the refrigerator is running continuously without cooling properly. Single quartz tube heater, 120V / 725W. Assembly measures 12-1/8" L x 3-3/8" W x 2-1/8" H. Includes heater and bracket. Replaces WR51X10030, AP3183311, 914088, SH323, and more. Compatible with GE, Hotpoint, Kenmore, Haier, Americana, Monogram, and Café. Common Problems This Part Fixes Frost or ice buildup covering the evaporator coils in the freezer compartment Freezer section warming up or not maintaining set temperature Fresh food section warming up even though the freezer is running Refrigerator running continuously but not cooling properly Visible frost accumulation on the freezer back wall behind the panel Defrost heater element visibly burned out, broken, or dark/charred at the ends Both compartments gradually warming up after working normally for years Replaces Part Numbers This defrost heater assembly directly replaces the following OEM and cross-reference part numbers: WR51X10055, WR51X10030, 914088, AGE29323, AH303781, AP3183311, EA303781, EAP303781, PD00001004, PS303781. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This defrost heater is compatible with select refrigerators from the following brands: GE refrigerators (side-by-side, French door, top-freezer, and bottom-freezer) Hotpoint refrigerators Kenmore / Sears refrigerators (select GE-built models) Haier refrigerators (select GE-platform models) Americana refrigerators Monogram refrigerators Café refrigerators Tip: When replacing the defrost heater, it is highly recommended to also replace the defrost thermostat (WR50X10068) and temperature sensor (WR55X10025) at the same time. These three parts form the defrost system and are commonly replaced together — replacing all three prevents a second disassembly if another component fails soon after. Key Features Single quartz tube glass heater — melts frost from the evaporator coils during each automatic defrost cycle, maintaining airflow and cooling efficiency Rated 120V / 725W — correct electrical specifications for compatible GE refrigerators Assembly dimensions: 12-1/8" L x 3-3/8" W x 2-1/8" H — direct fit into the evaporator coil bracket Includes heater element and mounting bracket — complete assembly ready to install Replaces WR51X10030 and WR51X10055 — both older and current part numbers covered Compatible with GE, Hotpoint, Kenmore, Haier, Americana, Monogram, and Café refrigerators Often replaced together with WR50X10068 defrost thermostat and WR55X10025 temperature sensor Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WR51X10055 Also Replaces WR51X10030 Part Type Refrigerator Defrost Heater and Bracket Assembly Condition Aftermarket Replacement Heater Type Single quartz tube glass heater Voltage 120V AC Wattage 725W Dimensions 12-1/8" L x 3-3/8" W x 2-1/8" H Includes Heater element and mounting bracket Often Replaced With WR50X10068 Defrost Thermostat, WR55X10025 Temperature Sensor Compatible Brands GE, Hotpoint, Kenmore, Haier, Americana, Monogram, Café Installation Notes ⚠️ Unplug Refrigerator Before Starting — Wear Work Gloves Unplug the refrigerator before beginning. Remove all food and shelving from the freezer compartment. Remove the freezer bottom drawer and the back panel screws (typically 2 hex-head screws). Slide out the back panel to expose the evaporator coils and defrost heater assembly. If the coils are covered in frost or ice, use a hair dryer to melt the ice before removing the heater — do not chip or force the heater free while iced over, as the glass element is fragile and will break. Disconnect the heater wires from the wiring harness — note the orientation before disconnecting. Remove the 2 Phillips screws securing the heater bracket and lift the heater assembly out. Install the new WR51X10055 heater assembly in the same position, reconnect the wires, and reinstall the bracket screws. Reinstall the back panel, shelving, and food. Restore power and verify the defrost cycle operates normally. Wear work gloves throughout — the evaporator area has sharp edges. Tools needed: Phillips screwdriver, 1/4" nut driver, hair dryer (if coils are iced over), work gloves. Frequently Asked Questions What does the refrigerator defrost heater do? Modern refrigerators use an automatic defrost system that periodically runs a defrost cycle — typically once or twice a day — to melt frost that accumulates on the evaporator coils during normal operation. The defrost heater is a glass quartz heating element that energizes during this cycle and melts the frost off the coils. This keeps the coils clear so air can flow freely through them to cool the refrigerator. When the heater fails, frost builds up unchecked on the coils over days or weeks — eventually blocking airflow completely and causing both compartments to warm up, even though the compressor is still running. How do I know if my defrost heater has failed? Remove the freezer back panel to expose the evaporator coils. If the coils are heavily coated in frost or solid ice — especially if both the freezer and refrigerator sections have been warming up — a failed defrost heater is the most likely cause. You can confirm with a multimeter: disconnect the heater and probe both wire ends. A working heater shows continuity (resistance between approximately 10–200 ohms at room temperature depending on wattage). No continuity confirms the heater element has burned out. Also visually inspect the glass tube — a burned, blackened, or broken tube is a clear sign of failure. Should I also replace the defrost thermostat and temperature sensor? Yes — since the freezer must be fully emptied and the back panel removed to replace the heater, it is highly recommended to also replace the defrost thermostat (WR50X10068) and temperature sensor (WR55X10025) at the same time. All three components form the defrost system and wear at similar rates. A failed thermostat or sensor can cause the heater to run too long or not at all — replacing all three in a single repair eliminates that risk and saves you from another complete freezer teardown in the near future. My freezer is warming up but the compressor is running — is it the defrost heater? It often is — but not always. A compressor that is running but not cooling can be caused by a failed defrost heater (frost blocking airflow), a faulty evaporator fan motor (air not circulating), a defrost thermostat or timer failure, or a sealed system problem (refrigerant leak or compressor issue). The easiest way to distinguish a defrost system failure from other causes is to open the freezer and check whether frost has built up on the back panel or coils. If yes, the defrost heater is the most likely culprit. If the coils are clear and the compressor is running, look at the evaporator fan or sealed system next. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured as a single quartz tube glass heater rated at 120V/725W to match the dimensions and performance of the original WR51X10055 defrost heater assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3977394 Dryer Thermal Cut-Off Kit –  Compatible with Whirlpool, Kenmore, Maytag, and KitchenAid Dryers Product Description Protect your dryer from overheating with the XPARTCO 3977394 Dryer Thermal Cut-Off Kit. This high-quality aftermarket replacement shuts off the heating element if the dryer temperature rises above safe operating limits. A failed cut-off can cause no-heat issues or overheating during drying cycles. Installing this reliable XPARTCO 3977394 kit restores safe temperature control and helps prevent damage to internal components. Replaces Part Numbers XPTC352, 3977394, 352F, EXPTC352 Compatibility This replacement thermal cut-off kit fits select Whirlpool, Kenmore, Maytag, Roper, Estate, Crosley, and KitchenAid dryers. Example compatible models include (but are not limited to): Whirlpool WED4815EW1, Kenmore 110.86573110, and Maytag MEDC215EW1. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM safety and temperature performance 🔥 Overheat Protection – Automatically shuts off power to the heating element if the dryer overheats 💰 Cost-Effective Fix – Affordable alternative to OEM thermal cut-off kits 🛠️ Easy Installation – Direct-fit design with included thermostats and connectors 🛡️ Fixes Common Issues – Solves dryer not heating, overheating, or shutting off prematurely 📐 Product Specification Part Number: 3977394 Component Type: Dryer Thermal Cut-Off Kit Includes: Thermal cut-off, high-limit thermostat, mounting hardware, and wire connectors Temperature Rating: Cut-off opens at ~352°F. Material: Metal thermostat housing and heat-resistant components Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Nut driver, Phillips screwdriver ⚠️ Safety First: Always unplug the dryer before performing any repairs to prevent electrical shock. Steps: Disconnect power and remove the rear dryer panel. Locate the heating element housing and identify the cut-off and thermostat. Disconnect wires and remove the old components. Install the new 3977394 cut-off and thermostat in the same locations. Reconnect wires, reassemble the back panel, and restore power. Run a short test cycle to verify proper heating. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Keep your dryer safe and efficient — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

XP53-0771 Dryer Thermostat This thermostat has a limit of 248°F. It will turn the heating element back on when the temperature drops by 80°F. Fits Maytag, Admiral, Norge Electric Dryers Replaces Part Numbers:WP53-0771, 53-0771, 53-0306, 53-1037, 53-1459, ER53-0771, OEM18028919, AP6009638, PS11742806, SET176, TJSET176.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO 280148 Dryer Thermostat Set – Compatible with Whirlpool, Kenmore, Maytag, Roper, Crosley, Amana Dryers Product Description Restore safe and efficient drying with the XPARTCO 280148 Dryer Thermostat Set. This replacement kit includes the high-limit thermostat and thermal cutoff fuse, ensuring your dryer shuts off overheating cycles and prevents potential hazards. A faulty thermostat or cutoff can cause the dryer to overheat, stop heating, or shut down mid-cycle. This set is a cost-effective solution to restore proper dryer function. Replaces Part Numbers 280148, 1175772, 280148VP, PD00002627, FIX991443, EAP991443, AH991443, AP3874047, EA991443, PS991443, 8318314, WP8557403, 8557403, 1180102, AP6013164, PS11746386. Compatibility This dryer thermostat set is compatible with select Whirlpool, Kenmore, Maytag, Roper, Crosley, and Amana dryers. Example compatible models include (but are not limited to): Whirlpool LER4634EQ2, Kenmore 110.66912690, Maytag MDE5500AYW. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Broad Compatibility – Fits Whirlpool, Kenmore, Maytag, Roper, Crosley, and Amana dryers 🔒 Safety Protection – Prevents overheating and protects against dryer fires 💰 Cost-Effective Repair Kit – Includes both high-limit thermostat and thermal fuse 🛠️ Easy DIY Installation – Only requires a screwdriver, installs in 20–30 minutes 🛡️ Fixes Common Issues – Restores heating, prevents shutdowns, resolves overheating problems 📐 Product Specification Part Number: 280148 Component Type: Dryer Thermostat Set (high-limit thermostat + thermal cutoff fuse) L146-44C, 295-111F with 50 Ohm thermistor. Material: High-temperature resistant metal and thermal fuse components Mounting: Direct replacement kit with standard connections Operating Conditions: Suitable for residential dryer heating systems Compliance: OEM-equivalent safety and performance standards 🛠️ Installation Notes Tools Needed: Phillips screwdriver, flathead screwdriver, needle-nose pliers ⚠️ Safety First: Always disconnect power before servicing your dryer to avoid electrical shock. Steps: Unplug dryer and locate the heating element housing. Remove screws securing access panel and locate old thermostat and fuse. Disconnect wire terminals from defective components. Replace with new thermostat and cutoff fuse from this kit. Reattach wires, secure components, and reinstall access panel. Restore power and test dryer operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Fix your dryer’s heating issues quickly — Add to Cart Now for a reliable, budget-friendly repair kit.

Read more less