Search results for "flame sensor"

XPARTCO 242278801 Refrigerator Temperature Sensor – Compatible with Frigidaire, Electrolux, and Kenmore Refrigerators Product Description Keep your refrigerator cooling accurately with the XPARTCO 242278801 Refrigerator Temperature Sensor. This high-quality replacement monitors the temperature inside the fresh-food and freezer compartments, sending signals to the control board to regulate cooling. A faulty sensor can cause temperature fluctuations, over-freezing, or warm spots. Replacing it with this reliable XPARTCO part ensures consistent temperature control and energy-efficient performance. Replaces Part Numbers 242278801 PD00029820, EAP8760187, AP5802148, 3016441, PS8760187. Compatibility This replacement temperature sensor fits select Frigidaire, Electrolux, and Kenmore refrigerators. Example compatible models include (but are not limited to): Frigidaire FFHS2611LBNA, Electrolux E23BC78IPS3, and Kenmore 253.7041341C. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature accuracy and response rate ❄️ Accurate Cooling Control – Monitors refrigerator temperature for consistent performance 💰 Cost-Effective Fix – Reliable alternative to expensive OEM parts 🛠️ Simple Installation – Plug-in design for fast, easy replacement 🛡️ Fixes Common Issues – Solves warm refrigerator, freezing, or inconsistent cooling problems 📐 Product Specification Part Number: 242278801 Component Type: Refrigerator Temperature Sensor (Thermistor) Material: Plastic housing with thermistor probe and wiring harness Resistance Range: Approximately 2.7 kΩ at 77°F (varies by temperature) Mounting: Direct-fit installation in refrigerator liner or evaporator area Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, wire clip removal tool ⚠️ Safety First: Always unplug the refrigerator before servicing to prevent electrical shock. Steps: Disconnect power and remove interior shelves for access. Locate the old temperature sensor, usually near the evaporator or rear wall. Disconnect the sensor’s wiring harness and remove clips. Install the new XPARTCO 242278801 sensor in the same position. Reconnect wiring, reassemble interior parts, and restore power. Allow several hours for the refrigerator to stabilize temperature. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Keep your refrigerator cooling efficiently — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

XPARTCO 6501KW2001A Washer Rotor Positioning Sensor – Compatible with LG and Kenmore Washers Product Description Restore accurate motor control and spin performance with the XPARTCO 6501KW2001A Washer Rotor Positioning Sensor. This Sensor Assembly, also known as a hall sensor is a replacement Part and is a vital component in Specific LG, Kenmore washer Models. This part monitors the direction and speed of the spinning rotor. It then communicates this information to the electronic control board. By doing so, it aids in the precise operation of your washer. If your washer pumps but fails to spin or agitate, it may be indicative of a damaged sensor assembly. Replaces Part Numbers 6501KW2001A, 6501KW2001D, PD00001726, EAP2497738, 6501KW2001C, EBR37560301, AP4457567, PS3529185.  Compatibility This replacement rotor positioning sensor fits select LG and Kenmore front-load washers. Example compatible models include (but are not limited to): LG WM2101HW, LG WM2487HRM, and Kenmore 796.40272900. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM performance and accuracy ⚙️ Precise Motor Feedback – Helps control drum rotation and spin speed 💰 Cost-Effective Solution – High-quality alternative to OEM sensor assembly 🛠️ Easy Installation – Plug-and-play design with secure connector fit 🛡️ Fixes Common Issues – Resolves LE, UE, or spin-related error codes 📐 Product Specification Part Number: 6501KW2001A Component Type: Washer Rotor Position Sensor (Hall Sensor) Material: High-durability circuit board and plastic housing Mounting: Direct-fit replacement on motor stator assembly Operating Conditions: Designed for high-humidity washer environments Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: 10mm socket wrench, Phillips screwdriver ⚠️ Safety First: Always unplug the washer before performing any repairs to prevent electrical shock. Steps: Disconnect power and remove the rear access panel. Remove the rotor bolt and pull off the rotor assembly. Locate and disconnect the wiring harness from the old sensor. Remove the old 6501KW2001A sensor and install the new XPARTCO replacement. Reconnect wiring, reinstall the rotor, and secure the rear panel. Restore power and run a spin test to verify repair. ⏱️ Time Required: 20–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Fix washer spin and motor issues — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

Choice DA32-10109Y Refrigerator Temperature Sensor – Replacement for Samsung Product Overview The DA32-10109Y Refrigerator Temperature Sensor is an aftermarket replacement part designed to measure and relay internal temperatures to the control board. A faulty sensor can lead to cooling problems, temperature fluctuations, or improper defrost cycles. Replacing a worn sensor with this reliable component helps restore accurate temperature readings and optimal cooling performance in your refrigerator. 8-1/4" overall length with two pin plug for freezer. Fits Samsung SXS refrigerator models. Replaces Part Numbers This sensor replaces part numbers DA32-10109Y, AP4136950, PS4138703. It is engineered to match the fit and functionality of the original Samsung sensor. Compatible Brands Compatible with many Samsung and Kenmore refrigerators manufactured by Samsung. Fits French door, bottom-freezer, and side-by-side models that use this temperature sensor. Fixes the Following Issues Refrigerator not cooling properly Freezer too warm or too cold Temperature reading errors Inconsistent cooling or defrost operation Why Buy from Parts‑O‑Matic Affordable and dependable aftermarket part Fast and free U.S. shipping Easy to install – no special tools required Trusted by appliance techs and DIYers

Read more less

XPARTCO WE04X10118 Dryer High Limit Thermostat Replaces Part Numbers: WE04X10118, 1089012, AH959918, EA959918, AP3794592, PS959918. Description: This High Limit Thermostat is a replacement part for specific GE dryer models. This safety component is designed to monitor and regulate the dryer's temperature, preventing it from exceeding safe levels. Mounted on the heating chamber or exhaust duct, the high limit thermostat shuts off the heat source or the dryer itself if it detects temperatures that are too high, helping to prevent overheating and potential fire hazards.   This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less

17438000001373 Washer Genuine OEM Water Level Sensor Assembly – Compatible with Midea, Insignia Washers Product Description Restore accurate water level detection and optimal washing performance with the 17438000001373 Washer Genuine OEM Water Level Sensor Assembly. This factory-original OEM sensor monitors water levels inside the washer and communicates with the control board to regulate fill cycles and ensure proper operation. A faulty sensor can lead to overfilling, underfilling, or cycles not completing correctly. Replacing it with this Genuine OEM assembly ensures precise sensing, proper communication with the control system, and long-lasting reliability. This part is manufactured to original factory specifications for dependable washer performance. Replaces Part Numbers 17438000001373, 302421600037, PS18188481 (verify if needed) Compatibility This Genuine OEM washer water level sensor assembly fits select Midea, Insignia washers. Common compatible models include (but are not limited to): Midea MAD160S2801GPSFMUS13, MLV41N1AWW, MAD160S2801PS, CTW41N1AW, MLV41N1AWWC, CLAWI47W, ATLMW41, CTW45N1AW, CTW45N2AW, CTW45N2AW, CTW45N1AW Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🏭 Genuine OEM Part – Manufactured to original factory specifications 💧 Accurate Water Level Detection – Ensures proper fill and cycle control ⚙️ Fixes Common Issues – Resolves overfill, underfill, and sensor errors 🧩 Complete Sensor Assembly – Ready for direct installation 💪 Reliable Performance – Designed for long-term durability ⚠️ Symptoms If your washer is experiencing any of the following issues, this part may need replacement: 💧 Washer overfilling or underfilling ⚠️ Incorrect water levels during cycles 🔄 Cycle not completing properly 🛑 Washer stopping mid-cycle 🚫 Continuous filling or no fill condition Replacing this sensor assembly can restore proper water level control and washer operation. 📐 Product Specification Part Number: 17438000001373 Component Type: Washer Water Level Sensor Assembly Function: Detects water level and communicates with control board Connection Type: Electrical connector + pressure sensing system Application: Washer fill and cycle control system OEM Status: Genuine OEM 🛠️ Installation Notes Tools Needed: Phillips screwdriver ⚠️ Safety First: Unplug the washer before servicing to avoid electrical shock. Basic Steps: Disconnect washer power. Access the control panel or top panel. Locate the water level sensor assembly. Disconnect wiring and any attached pressure hose. Remove mounting screws and remove the old sensor. Install the new 17438000001373 Genuine OEM sensor. Reconnect wiring, reassemble, and restore power. Run a test cycle to confirm proper operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🏭 Genuine OEM Appliance Part 🚚 Free Shipping on All Orders 🔄 30-Day Return Policy Restore factory-level washer performance and accurate water control — Add to Cart Now with confidence!

Read more less

3204267 Dryer Genuine High-Limit Thermostat Replaces Part Numbers: 3204267, 145160, 508516, 73204267, AH446428, EA446428, OEM8525910, AP2131477, PS446428, WE4X757, WE04X0757, WE04X10002, WE4X10002, AH268202, EA268202, OEM8171210, AP2042802, PS268202. Description: This High Limit Thermostat is a Genuine part for specific Frigidaire, GE dryer models. It serves as a critical safety device, designed to cut off the power to the heating element if the dryer overheats. This thermostat helps prevent potential fire hazards by maintaining a safe operating temperature within the dryer. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

Genuine OEM Dryer Part W11683629 Dryer Genuine OEM Thermistor A manufacturer-approved temperature-sensing component designed to help the dryer control system regulate heat and drying performance. Product Description The W11683629 Dryer Genuine OEM Thermistor monitors air temperature inside the dryer and sends temperature information to the electronic control system. The control uses this signal to cycle the heat source and maintain the correct operating temperature during the drying cycle. This is a Genuine OEM replacement part manufactured to the original equipment specifications for fit, electrical response, and dependable operation. Replacing a failed thermistor can help restore accurate temperature control, normal cycle times, and consistent drying results. Quick Answer W11683629 is a Genuine OEM dryer thermistor. It senses dryer air temperature and communicates with the control board so the appliance can regulate heating. Replace it when testing or diagnosis confirms an open, shorted, damaged, or inaccurate temperature sensor. Common Problems This Part Fixes Dryer overheats or runs hotter than normal Clothes remain damp after a complete cycle Drying cycles take too long Heat cycles on and off incorrectly Dryer stops before clothes are dry Temperature-sensor or heating-related error codes Replaces Part Number The product title identifies the following part number: W11683629, W11452857, AP7216892, AWP1400864, PS17216463.  No additional replacement or cross-reference number was included in the supplied product title. Compatibility Designed for select dryer models that specify Genuine OEM part number W11683629. Appliance parts can look similar while using different resistance ranges, connectors, mounting positions, or control logic. Always verify the complete dryer model number and the required part number before ordering. The model-number label is commonly located around the door opening, on the cabinet frame, or on the rear identification plate. Key Features Genuine OEM manufacturer-approved component Monitors dryer operating temperature Sends temperature feedback to the control system Helps regulate heating and cycle performance Built to original fit and electrical specifications Direct replacement when W11683629 is specified Product Specifications Part Number W11683629 Part Type Dryer Thermistor / Temperature Sensor Condition New Quality Genuine OEM Application Clothes Dryer Primary Function Measures air temperature for the dryer control system Package Quantity 1 Thermistor Troubleshooting Guide Disconnect the dryer from electrical power before opening or servicing the cabinet. Inspect the exhaust vent, lint path, and blower area. Restricted airflow can produce symptoms similar to a failed thermistor. Inspect the thermistor body, terminals, connector, and wire harness for damage, corrosion, loose connections, or heat discoloration. Disconnect the thermistor and test resistance with a multimeter. Compare the reading with the dryer service information for the measured temperature. Warm or cool the sensor carefully. Resistance should change smoothly as temperature changes; an open circuit, short circuit, or unstable reading can indicate failure. Check the heater circuit, thermal devices, moisture-sensing system, and control board when the thermistor tests within specification. Safety: Do not bypass a thermistor or protective temperature device. Installation and diagnosis should be performed by a qualified person when you are not comfortable servicing electrical appliances. When Should You Replace This Part? The thermistor is open, shorted, or outside the specified resistance range The sensor reading does not change correctly with temperature The housing or connector is cracked, burned, or physically damaged A service diagnostic identifies W11683629 as the failed component Airflow and related heating components have been checked and the thermistor fails testing Shop With Confidence Purchase the correct Genuine OEM replacement part for dependable fit and performance. Verify your dryer model number before ordering, and contact our parts team when compatibility assistance is needed. Genuine OEM Fast U.S. Shipping Compatibility Support Secure Checkout  

Read more less

Genuine OEM Frigidaire / Electrolux Washer Part 134762010 Washer Genuine OEM Water Level Pressure Switch Monitors air pressure from the washer tub and signals the control system when the correct water level has been reached. Product Overview The Frigidaire 134762010 Washer Water Level Pressure Switch senses changes in air pressure through the washer pressure hose to monitor the amount of water inside the tub. It signals the washer control system when the correct water level has been reached so the appliance can fill, wash, drain, and advance through the cycle correctly. This is a new Genuine OEM Frigidaire / Electrolux replacement part manufactured to the original equipment specifications for proper fit, electrical connection, and operation in compatible washers. Quick Answer 134762010 is a Genuine OEM water-level pressure switch for select Frigidaire, Electrolux, Kenmore, and Crosley front-load washers. It replaces 7134762010. This listing is for the pressure switch only; the pressure hose, clamp, wiring harness, and mounting hardware are not included unless specifically shown. Common Problems This Part May Fix Washer overfills with water Washer does not fill or underfills Incorrect or inconsistent water level Cycle stops or will not advance Washer does not drain or complete the cycle correctly E35 or another water-level-related error on applicable models Replaces and Cross-References 134762010, 1482962, 7134762010, AH2349296, AP4368525, AFR14413, EA2349296, PD00007813, PS2349296. 134762010 is the current manufacturer part number. Other numbers are previous manufacturer or retailer cross-references. Compatibility Designed for select front-load washers manufactured by Electrolux and sold under Frigidaire, Electrolux, Kenmore, and Crosley brand names. Confirmed model examples include: 41741100000 41744130000 EIFLS55IRR0 EIFLS60JIW1 FAFS4473LN0 FAFW3921NW0 FFFW5000QW0 CFW4700LW0 CFW7400QW0 Important: This is a partial compatibility list. Pressure switches can look alike while using different settings, terminals, mounting tabs, or control calibration. Verify the complete washer model number before ordering. Key Features Genuine OEM Frigidaire / Electrolux replacement part Monitors the water level inside the washer tub Signals the control system when the correct fill level is reached Supports proper filling, washing, draining, and cycle operation Snap-tab mounting design on compatible models Designed for original fit and electrical connection Product Specifications Manufacturer Part Number 134762010 Brand Frigidaire / Electrolux Part Type Washer Water Level Pressure Switch Condition New Quality Genuine OEM Application Front-Load Washing Machine Primary Function Senses and controls the washer water level Included One Water Level Pressure Switch Installation Notes Unplug the washer and shut off both water-supply valves. Remove the washer top panel as required for your model. Photograph the wire connector and pressure-hose connection before disconnecting them. Disconnect the electrical connector without pulling on the wires. Release the clamp and carefully remove the pressure hose. Remove the old switch and install the replacement in the same position. Reconnect the hose, clamp, and electrical connector, then reinstall the top panel. Diagnostic tip: Inspect the pressure hose for cracks, pinholes, blockage, moisture, loose connections, or trapped debris. A damaged or obstructed hose can cause the same symptoms as a failed pressure switch. Frequently Asked Questions Is 134762010 a genuine OEM part? Yes. It is a Genuine OEM Frigidaire / Electrolux washer water-level pressure switch. What does the pressure switch do? It monitors air pressure from the washer tub and signals the control system when the correct water level has been reached. Which part number does it replace? It replaces previous manufacturer part number 7134762010. Does this include the pressure hose? No. The listing is for the pressure switch only unless additional components are specifically shown and stated as included. Will it fit every Frigidaire or Electrolux washer? No. Verify the complete appliance model number and required manufacturer part number before purchasing. Shop With Confidence Purchase the correct Genuine OEM replacement part for dependable fit and operation. Verify your washer model number before ordering, and contact our parts team when compatibility assistance is needed. Genuine OEM PartFast U.S. ShippingCompatibility SupportSecure Checkout

Read more less

WE04X20685 Dryer Genuine OEM Thermistor Replaces Part Number: WE04X20685, WE4M336, 4369857, AP5985030, PS11721518. Description: The Thermistor is an OEM replacement part for GE dryers. This temperature-sensing device monitors air exhaust temperatures and communicates real-time readings to the control board. Precise thermistor functioning ensures the heating elements and drum engage safely and appropriately.  

Read more less

ERP 3977767 Dryer Hi Limit Thermostat 250 -80F Limit Thermostat. Fits specific Maytag, Kenmore, Whirlpool dryer models. Replaces Part Number: WP3977767, 3977767, 3399693, ER3977767, SET185, TJ90SET185, WP3977767VP, AP6009043, PS11742185. Description: This Hi-Limit Thermostat is a replacement part for specific Maytag, Kenmore, Whirlpool dryer models. It functions as a critical safety device that monitors and controls the temperature within the dryer, preventing it from overheating. When the dryer reaches a temperature that is too high, this thermostat will cut off the power to the heating element to mitigate the risk of fire.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

WE04X25198 Dryer Genuine OEM Thermostat Fits Specific GE Dryer Models.  Replaces Part Numbers: WE04X25198, 4467032, AP6024634, PS11736631. Description: This Thermostat is a Genuine OEM component specifically designed for specific GE laundry machine models. It is a heat-sensing component that monitors and regulates air temperatures inside the dryer drum. Precise thermostat functioning ensures proper drying temperatures are reached and maintained for optimal performance.  

Read more less

6322FR2046CCM Washer Thermistor Assembly Monitors water temperature Fits LG and Kenmore Washer Replaces Part Numbers:6322FR2046C, 6322FR2046B, 1268202, 6322FR2046F, 6322FR2046W, AH3528953, EA3528953, AP4445159, PS3528953. Description: This Thermistor Assembly is a replacement part for select front loading LG washing machine models. It plays an important role in monitoring and regulating temperatures during heated wash cycles. The thermistor detects temperature changes within the wash drum and sends this information to the control board to ensure clothes are washed at the optimal temperature.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less