Search results for "washer knobs"

WH23X29538 Washer Genuine OEM Water Valve Fits Specific GE Washer Models. Replaces Part Number WH23X29538, OEM20970350, AP6990115, PS16217225 Description: This Water Valve is a replacement part compatible with specific GE  washing machine models. As a key component located inside the washer cabinet, this valve precisely controls the flow of water into the machine during wash cycles. It allows for the filling of the tub with the proper amount of water at the correct temperature per the settings.

Read more less

XPARTCO W11366438 Range Surface Burner Knob Product Overview The XPARTCO W11366438 Range Surface Burner Knob is designed to control the heat level of your stove burners with precision. This high-quality replacement knob restores smooth operation and enhances the appearance of your cooktop. Quick Answer If your stove knob is cracked, loose, missing, or difficult to turn, the W11366438 burner knob is likely worn out. Replacing it restores proper burner control and usability. Replaces Part Numbers Replaces OEM part number: W11366438, W11084623, 4929319, W11359382, W11505414, EAP12723935, AWP44385, PD00054489, AP6888134, PS12723935. Compatibility This surface burner knob is compatible with select Whirlpool, Maytag, and other compatible ranges. Whirlpool Ranges Maytag Ranges Always verify your appliance model number before ordering. Common Problems This Part Fixes Broken or cracked knob Knob slipping or not engaging Missing control knob Difficulty adjusting burner heat Key Features Restores precise burner control Easy push-on installation High-quality aftermarket replacement Durable construction for daily use Product Specifications Part Number: XPW11366438 Part Type: Range Surface Burner Knob Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Range Burner Control Troubleshooting Guide Knob spins freely → Worn insert Cannot adjust flame → Damaged knob Knob falls off → Cracked fitting When Should You Replace This Knob? Replace this knob if it is cracked, loose, missing, or not functioning properly. Installation Notes ⚠️ Ensure the appliance is off. Pull the old knob straight off and push the new knob firmly onto the control shaft. Related Parts Surface Burner Valve Igniter Switch Control Panel Overlay Frequently Asked Questions Will this knob fit my range?This knob fits many Whirlpool and compatible models. Always verify your model number. Is installation difficult?No, this knob is typically push-on and easy to install. What are signs of a bad knob?Cracks, slipping, or inability to control heat settings. Is this OEM or aftermarket?This is a high-quality aftermarket replacement part. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support

Read more less

WPW10415450 Genuine OEM Whirlpool Range Burner Knob The WPW10415450 is a genuine Whirlpool OEM surface burner control knob for gas ranges and cooktops. This is the knob you turn to light and adjust a surface burner — it fits onto a D-shaped valve stem behind the control panel, and its position controls how far the gas valve opens, from off through lite, hi, medium, and low. Markings printed around the perimeter line up with an indicator arrow on the control panel so you can see exactly what setting you've selected. Finished in stainless steel/chrome, approximately 2" in diameter. Over years of use, the knob's internal D-shaped socket can wear out and stop gripping the valve stem securely, or the knob itself can crack, melt slightly from heat exposure, or simply wear down from repeated turning. A worn or damaged knob typically shows up as difficulty adjusting the burner heat, a knob that feels loose or wobbly, a knob that spins without turning the valve, or one that no longer seats securely onto the shaft. It directly replaces W10415450, AP6021125, 2118719, PS11754446, EAP11754446, W10294797, W10325899, and PD00007159. Quick Answer The WPW10415450 Genuine OEM Whirlpool Range Burner Knob fixes Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore gas ranges with a burner knob that's cracked, loose, wobbly, spins without adjusting the flame, or won't seat onto the valve stem. Stainless steel/chrome finish, 2" diameter, fits a D-shaped shaft. Replaces W10415450, AP6021125, 2118719, PS11754446, EAP11754446, W10294797, W10325899, PD00007159. Visually similar knobs W10284885 and W10316664 are NOT compatible with this part despite looking alike. Common Problems This Part Fixes Difficulty turning or adjusting the burner heat setting Knob feels loose or wobbly on the shaft Knob spins freely without turning the gas valve Knob won't seat securely onto the valve stem Visible cracks, melting, or heat damage on the knob Knob missing entirely, making burner adjustment impossible Setting markings no longer line up correctly with the indicator arrow Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This range burner control knob directly replaces the following OEM and cross-reference part numbers: WPW10415450, W10415450, AP6021125, 2118719, PS11754446, EAP11754446, W10294797, W10325899, AWP50229, PD00007159 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This burner knob is compatible with select Whirlpool gas ranges and cooktops, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea appliances built on the Whirlpool platform, including model numbers such as: GG388LXB01, GG388LXB02, GG388LXB03, GG388LXQ01, GG388LXQ02, GG388LXS04, GG388LXS05 GG390LXB01, GG390LXB03 GCG388LXQ03 GGG388LXB04, GGG388LXO04, GGG390LXQ01, GGG390LXS01, GGG390LXS02 Note — visually similar knobs are NOT compatible: Whirlpool uses several burner knobs that look nearly identical to this one but are not interchangeable, including W10284885 and W10316664. Same appearance does not mean same fit — these knobs use different internal shaft sockets and will not seat correctly on this valve stem. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which knob fits your range. Key Features Genuine Whirlpool OEM part — factory-specified D-shaft socket and setting markings Fits a D-shaped burner valve stem for a secure, non-slip grip Resolves "loose or wobbly knob," "spins without adjusting flame," "won't seat on the shaft," and "cracked or damaged knob" symptoms Stainless steel/chrome finish, approximately 2" diameter Clear off/lite/hi/med/low markings aligned to the control panel indicator arrow No tools required — simple pull-off, push-on installation Replaces W10415450, AP6021125, 2118719, PS11754446, EAP11754446, W10294797, W10325899, and PD00007159 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea gas ranges Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WPW10415450 Part Type Range Surface Burner Control Knob Condition Genuine OEM Brand Whirlpool Application Gas Ranges and Cooktops Finish Chrome Diameter Approx. 2 in. Shaft Type D-shaped valve stem Settings Off, Lite, Hi, Med, Low Repair Difficulty Very Easy — no tools required Quantity 1 knob Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, Ikea Installation Notes ⚠️ Unplug Range Or Shut Off Breaker Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Pull the old knob straight off the valve stem — on most models this requires no tools, just firm, even pressure in the direction of the indicator arrow. Confirm the new WPW10415450 knob by checking that the part number matches before installing. Align the top of the new knob with the control panel's indicator arrow, then press the knob onto the D-shaped shaft until you feel and hear it click securely into place. Restore power and test that the knob turns smoothly through its full range, with the markings lining up correctly against the indicator arrow at each setting. Tools needed: none. Frequently Asked Questions My knob spins but doesn't seem to change the burner flame. Is this the right part? Yes, this is a common symptom of a worn knob. Over time, the internal D-shaped socket that grips the valve stem can wear out, letting the knob spin independently of the shaft instead of turning it. Replacing the knob restores that positive connection so turning it actually opens and closes the gas valve as expected. I found a knob online that looks identical but has a different part number. Will it work? Not necessarily, and this is worth being careful about. Whirlpool uses several burner knobs, including W10284885 and W10316664, that closely resemble this one visually but use different internal shaft sockets and are not compatible with this valve stem. Always match the exact part number rather than relying on appearance, and verify against your model number if you're unsure. Do I need any tools to replace this knob? No. This is a simple pull-off, push-on repair — remove the old knob by pulling it straight off the shaft, then press the new one on until it clicks into place. No screws, no disassembly of the control panel required. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original D-shaft socket, finish, and setting markings of the burner knob originally installed on your range. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

74009592CM Burner Control Knob Black plastic burner knob Fits Specific Maytag, Jenn Air, Whirlpool ranges Replaces Part Numbers: WP74009592, 74009592, 1032643, 71003477, AP6011140, PS11744334. Description: This Top Burner Control Knob is a replacement part for specific Whirlpool ranges and cooktop models. This part allows for precise control over the heat level of the stove's burners, enabling users to adjust the flame size for various cooking needs. Constructed from durable materials, the knob is designed to withstand the rigors of daily use, providing a reliable interface for setting and maintaining the desired cooking temperature. This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

WH44X10288 Washer Lid Lock and Switch Assembly Replaces Part Numbers: WH44X10288, 1974376, AH3496878, EA3496878, AP5270191, PS3496878. 120V, 60Hz, lid lock and switch assembly. Fits select GE laundry center. Description: This Door Latch Lid Lock is a replacement part for select GE washing machine models. It is designed to securely lock the washing machine's lid or door during operation, ensuring safety and preventing water from spilling during the wash cycle.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

(5 Pack) ERP W10594481 Surface Burner Knob 3/8" stem length, 3 o'clock flat, 0.256 Mold#: 5T03 Replaces Part Numbers:WPW10594481, W10594481, AP6023301, PS11756643   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

W11307244 Genuine OEM Washer Lid Lock Assembly for Whirlpool, Maytag, Kenmore, Amana Fix your washing machine with the W11307244 Genuine OEM Lid Lock Assembly, designed for top-loading washers from trusted brands like Whirlpool, Maytag, Kenmore, Amana, Crosley, and more. Ensure safety and seamless operation with this high-quality, manufacturer-approved replacement part. Fix issues like a washer that won’t start, stops mid-cycle, or displays lid lock errors with this reliable solution. Product Features 🔒 Genuine OEM Quality: Engineered by Whirlpool for perfect compatibility and long-lasting performance. 🔄 Universal Fit: Replaces part numbers W10682535, W10838613, W10838613VP, W11253733. Compatible with models like Whirlpool WTW5000DW1, Maytag MVWC565FW1, Amana NTW4516FW0, Kenmore 110.2024251, and more (verify with your model number). 🛠️ Easy Installation: Comes with a 3-wire harness for quick setup. Basic tools (screwdriver, putty knife, wrench) needed for DIY repair. ✅ Enhanced Safety: Securely locks the washer lid during cycles to prevent accidents and ensure smooth operation. Why Choose This Lid Lock Assembly? The W11307244 is the ideal solution for common washer issues like: 🚫 Washer failing to start or fill. 🔴 Lid not locking properly, triggering error codes. ⏸️ Machine pausing mid-cycle or during spin. ⚙️ Inconsistent agitation or cycle completion. Unlike generic alternatives, this OEM part guarantees precise fit and durability, saving you time and money on repairs. Compatibility Fits a wide range of top-load washing machines, including: Whirlpool: WTW5000DW1, MVWX655DW1 Maytag: MVWC565FW1, ATW4516HW0 Amana: NTW4516FW0 Kenmore: 110.2024251 Crosley, Roper, Inglis: Various models (check your manual for compatibility). Pro Tip: Confirm your washer’s model number to ensure a perfect fit. Contact us for help verifying compatibility! Installation Guide 🔌 Unplug the washer and turn off the water supply for safety. 🔧 Use a putty knife to release clips and lift the top panel. 🔌 Disconnect the old harness and remove the faulty lock. 🔩 Install the W11307244 assembly, ensuring proper alignment of the bezel. ✅ Reconnect the harness, reassemble, and test the lock before full use. Note: The part may arrive locked; manually unlock it during installation. Watch our installation video for step-by-step guidance. Why Shop With Us? 🚚 Fast, Free Shipping: Same-day dispatch on orders before 2 PM EST. 😊 100% Satisfaction Guarantee: 30-day hassle-free returns. 🧑🔧 Expert Support: Our team is here to assist with compatibility and installation questions. 💸 Competitive Pricing: Get OEM quality at an affordable price. Customer Reviews ⭐⭐⭐⭐⭐ "Fixed my Whirlpool washer in 20 minutes! Easy to install and works perfectly." – Sarah T.⭐⭐⭐⭐⭐ "OEM part made all the difference. My Maytag is back to normal!" – John R.⭐⭐⭐⭐ "Arrived quickly, but needed to unlock it before install. Great product!" – Lisa M. Add to Cart Now! Don’t let a faulty lid lock disrupt your laundry routine. Order the W11307244 Genuine OEM Lid Lock Assembly today and restore your washer’s performance. Limited stock—grab yours now!

Read more less

W11481722 Genuine OEM Whirlpool Washer Shift Actuator The W11481722 is a genuine Whirlpool OEM shift actuator (gear case) for Whirlpool, Maytag, Amana, Crosley, and Kenmore top-load washers. Mounted at the bottom of the washer, this component does two jobs in one assembly: it physically shifts the transmission between modes by moving an arm on the cam assembly, engaging and disengaging either the basket or the agitator/washplate depending on what the cycle calls for, and it houses the tachometer that reports drum speed back to the control board throughout the cycle. Rated 120V, 60Hz, with a 6-pin wire connector for a direct plug-in fit. Because this single part handles both mechanical shifting and speed sensing, a failure here can produce a range of symptoms depending on which function is affected: the washer may fail to spin or agitate properly, get stuck in one mode without transitioning to the other, or the control board may throw an error code related to a lost tachometer signal or improper basket engagement. It directly replaces AP6990751, W10597177, WPW10597177, W11237117, W11398781. Quick Answer The W11481722 Genuine OEM Whirlpool Washer Shift Actuator fixes Whirlpool, Maytag, Amana, Crosley, and Kenmore top-load washers that won't spin or agitate properly, get stuck in one mode, or throw a tachometer/basket-engagement error code. 120V, 60Hz, 6-pin connector. Replaces AP6990751, W10597177, WPW10597177, W11237117, W11398781. This part also contains the tachometer — a single failure here can affect both cycle shifting and speed sensing at once. Common Problems This Part Fixes Washer won't spin Washer won't agitate Washer gets stuck in one mode and won't transition between agitate and spin Error code related to a tachometer signal or basket engagement Basket doesn't engage or disengage correctly during the cycle Cycle stalls partway through as the control loses accurate speed feedback Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer shift actuator directly replaces the following OEM and cross-reference part numbers: W11481722, W10597177, WPW10597177, W11237117, W11398781, AP6990751, AWP45140, EAP16221077, PD00067016, PS16221077 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This shift actuator is compatible with select Whirlpool top-load washers, and also fits select Maytag, Amana, Crosley, and Kenmore washers built on the Whirlpool platform, including model numbers such as: WTW5100HW1, WTW5100HC1, WTW6120HC1 WTW4616FW3, WTW4655JW2, WTW4715EW0, WTW4715EW2 WET4027HW2, WETLV27HW3, WGT4027HW0, WGTLV27HW0 NTW4516FW0, NTW4516FW2, NTW4516FW4, NTW4519JW2 NTW4601BQ1, NTW4605EW0, NTW4611BQ1, NTW4615EW0, NTW4631BQ1, NTW4635EW0, NTW4651BQ1, NTW4655EW0, NTW4701BQ1, NTW4705EW0, NTW4750BQ1, NTW4755EW0 Crosley VAW3584GW0, VAW3584GW1, VAW3584GW2 Kenmore 110-series models (110.xxxxx) Note: Always verify your full model number before ordering, since Whirlpool uses several different shift actuator designs across its washer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified shifting mechanism and tachometer calibration Combines two functions in one assembly: transmission mode shifting and drum speed sensing Resolves "won't spin," "won't agitate," "stuck in one mode," and "tachometer error code" symptoms Rated 120V, 60Hz 6-pin connector for a direct plug-in electrical fit Direct drop-in replacement — mounts to the original gear case position Replaces W10597177, W11237117, W11398781, WPW10597177, and W10625252 Compatible with Whirlpool, Maytag, Amana, Crosley, and Kenmore top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11481722 Part Type Washer Shift Actuator (Gear Case) Condition Genuine OEM Brand Whirlpool Location Bottom of the washer, in the gear case Function Shifts transmission between agitate/wash and spin modes; houses the tachometer Voltage 120V Frequency 60 Hz Connector 6-pin Material Metal Repair Difficulty Moderate — gear case access required Quantity 1 shift actuator Compatible Brands Whirlpool, Maytag, Amana, Crosley, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Note Cam Position Before Removal Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access to the shift actuator is through the gear case at the bottom of the washer, which typically requires tipping the washer back or removing surrounding panels per your model's service instructions to reach it. Photograph the wiring harness connection and the actuator's mounting position before disconnecting anything. Disconnect the 6-pin wiring harness connector from the old actuator, remove its mounting screws, and pull it free from the gear case. Install the new W11481722 in the same position, secure the mounting screws, and reconnect the 6-pin harness connector fully. Reassemble any panels removed for access, restore power, and run a full test cycle through both agitate and spin to confirm the washer shifts between modes correctly with no error codes. Tools needed: Phillips or nut driver screwdriver, work gloves. Frequently Asked Questions My washer is stuck in one mode — it will either agitate or spin, but not both. Is this the shift actuator? Yes, this is a classic symptom of a failed shift actuator. This part is what physically moves the arm on the cam assembly to switch the transmission between agitate/wash mode and spin mode. If it fails, the washer can get mechanically stuck engaging only one of those two functions, since the shifting mechanism itself is no longer moving the cam correctly. My control board shows a tachometer error. Why would that be the shift actuator and not something else? Because this single part combines both the mechanical shifting function and the tachometer that reports drum speed to the control board, a failure inside the actuator can knock out the speed-sensing function even if the shifting mechanism is unaffected, or vice versa. A tachometer-related error code is a direct signal that this component — not a separate sensor — is the likely cause. Is this a difficult repair? It's a moderate repair, since accessing the gear case at the bottom of the washer typically requires tipping the unit back or removing surrounding panels, depending on your specific model. It's within reach for a confident DIYer with basic hand tools, but budget more time than a simple top-panel swap. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original shifting mechanism, tachometer calibration, and 6-pin harness configuration of the shift actuator originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 8181651 Washer Door Striker  Replaces Part Numbers: WP8181651, 8181651, 906446, AP6011711, PS11744910. Description: This Door Strike is a replacement part for specific Maytag, Kenmore, Whirlpool washing machine models. This component is responsible for providing a secure and proper closure for the washer door, ensuring it seals tightly during operation. This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less

W10404050 Genuine OEM Washer Lid Switch Assembly The W10404050 is a Genuine OEM replacement lid switch and latch assembly compatible with select Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Roper, Admiral, Crosley, Inglis, Magic Chef, and Norge top-load washers. The lid switch is a critical safety component that detects when the washer lid is opened or closed. It sends a signal to the control board to allow the washer to fill, agitate, and spin when the lid is closed — and to immediately stop the spin cycle when the lid is opened, preventing contact with a moving drum. This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It features a 4-wire plug connection and includes two bezels (one white and one gray) to match different model color schemes. It directly replaces W10238287, W10744659, W10404050VP, AP5263307, and several additional cross-reference numbers. The companion lid strike (W10240513) is sold separately — inspect the strike on your lid for wear or damage and replace if needed. Installs in 20–30 minutes with basic hand tools. Quick Answer The W10404050 Genuine OEM Washer Lid Switch Assembly fixes top-load washers that won't start, won't spin, have a blinking lid lock light, or continue spinning with the lid open. 4-wire plug connection. Includes white and gray bezels. Replaces W10238287, W10744659, AP5263307, and more. Compatible with Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Roper, Admiral, Crosley, Inglis, Magic Chef, and Norge washers. Lid strike W10240513 sold separately. Common Problems This Part Fixes Washer will not start — lid lock light blinks without locking Washer fills but will not agitate or spin Washer lid lock light continuously blinks and clicks without engaging Washer continues to spin with the lid open — safety mechanism not working Lid appears locked but washer will not proceed past sensing or fill cycle Washer stops mid-cycle and will not restart without opening and re-closing the lid Lid lock assembly visibly broken or latch no longer springs back after pressing Replaces Part Numbers This lid switch assembly directly replaces the following OEM and cross-reference part numbers: W10404050, 1938607, W10238287, W10404050VP, W10744659, EAP3497627, AWP41256, PD00003596, AH3497627, AP5263307, EA3497627, PS3497627. Contact our support team with your model number if you need confirmation before ordering. Compatibility This lid switch assembly is compatible with select top-load washers from the following brands: Whirlpool top-load washers — Cabrio and WTW series (electronic top-load models) Maytag top-load washers — Centennial, Bravos X, and MVWC/MVWX series Kenmore / Sears top-load washers — 110 series and select others (Whirlpool-built) Amana top-load washers — NTW and ATW series KitchenAid top-load washers Roper top-load washers Admiral top-load washers — ATW series Crosley top-load washers Inglis top-load washers Magic Chef top-load washers Norge top-load washers Note: The W10404050 is for electronic top-load washers with a 4-wire lid lock (Cabrio, Centennial, Bravos, and similar platforms). Older mechanical top-load washers use a different lid switch style. Verify your model number before ordering. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Critical safety component — stops the spin cycle when the lid is opened to prevent contact with a moving drum Signals the control board to allow filling, agitating, and spinning when the lid is properly closed and locked 4-wire plug connection — direct plug-in replacement on compatible models Includes two bezels (white and gray) to match different model color schemes Replaces W10238287, W10744659, W10404050VP, AP5263307, and more Compatible with Whirlpool Cabrio, Maytag Centennial, Maytag Bravos X, Kenmore 110 series, and many more Lid strike W10240513 sold separately — inspect and replace if worn Product Specifications Part Number W10404050 Part Type Washer Lid Switch and Latch Assembly Condition Genuine OEM Application Electronic Top-Load Washers (4-wire lid lock) Connector 4-wire plug Color White (includes both white and gray bezels) Includes Lid switch assembly, white bezel, gray bezel Companion Part W10240513 Lid Strike (sold separately) Compatible Brands Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Roper, Admiral, Crosley, Inglis, Magic Chef, Norge Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power before beginning any repair. The lid switch assembly is mounted under the washer's top panel near the lid opening. To access it, insert a putty knife about 2 inches from each front corner of the top panel to release the spring clips and lift the top panel. Disconnect the 4-wire harness from the old lid switch assembly. Remove the mounting screws securing the assembly and lift it out. Install the new W10404050 assembly, secure with the mounting screws, and reconnect the 4-wire harness. Choose the appropriate bezel (white or gray) for your model and snap it into place. Lower the top panel until the clips engage. Restore power and run a test cycle to confirm the lid locks, the washer starts, and the spin cycle stops when the lid is opened. Tip: While the top panel is raised, inspect the lid strike (W10240513) on the lid for cracks or wear — if worn, replace it at the same time. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions What does the washer lid switch do? The lid switch assembly serves two functions. First, it is a safety device — when the lid is opened during the spin cycle, the switch immediately cuts power to the spin motor to prevent contact with the moving drum. Second, it signals the control board that the lid is securely closed and locked, allowing the washer to proceed through the fill, agitate, and spin cycles. If the switch fails, the washer either won't start at all, or will fail to proceed past a specific cycle stage because the board cannot confirm the lid is closed. My lid lock light is blinking — does that mean the lid switch needs to be replaced? A blinking lid lock light is one of the most common symptoms of a failed W10404050 lid switch assembly. It typically means the lid lock mechanism is attempting to engage but failing — either because the switch is internally faulty or because the lid strike (W10240513) on the lid is broken and not triggering the switch properly. Inspect the lid strike first — if it is cracked or missing, replace it. If the strike looks intact and the lid lock still blinks without engaging, replace the W10404050 switch assembly. Should I also replace the lid strike (W10240513) at the same time? It depends on the condition of the strike. Open the lid and inspect the two plastic prongs on the underside of the lid that engage the W10404050 latch — this is the W10240513 lid strike. If the prongs are cracked, broken, or noticeably worn down, replace the strike at the same time as the switch assembly. Since the top panel is already lifted for the switch replacement, it is a good opportunity to inspect and replace the strike if needed, using only a Phillips screwdriver. What washers is the W10404050 compatible with? The W10404050 is used on Whirlpool Cabrio and WTW series electronic top-load washers, Maytag Centennial and Bravos X top-load washers, and Kenmore 110 series top-load washers, among others. It is specifically for electronic top-load models with a 4-wire lid lock — not for older mechanical top-load washers that use a simpler 2- or 3-wire lid switch. Verify your model number before ordering. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same lid switch and latch assembly installed in compatible washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH23X29553 Washer Water Valve The XPARTCO WH23X29553 is an aftermarket replacement water inlet valve for GE front-load washers, and also fits select Hotpoint, RCA, Haier, Monogram, and Café models. This valve controls the flow of water into the washer from the household supply line — when the control calls for a fill, the valve's solenoid opens to admit water, and closes again once the correct level is reached. Built with an ABS plastic body and stainless steel components for durability against corrosion. Common failure causes include mineral or sediment buildup inside the valve body, a burned-out internal solenoid coil, and general wear over years of use. A failing valve typically shows up as the washer not filling properly, filling too slowly, or leaking water. It directly replaces AP6983554, PS12743643, EAP12743643, 33090202, and 0024000126GA. As an aftermarket replacement, the WH23X29553 is built to OEM-equivalent quality standards. Quick Answer The XPARTCO WH23X29553 Washer Water Valve fixes GE front-load washers (and select Hotpoint, RCA, Haier, Monogram, and Café models) that aren't filling properly, are filling too slowly, or are leaking water near the valve connections. Replaces AP6983554, PS12743643, EAP12743643, 33090202, 0024000126GA. Not the same part as the similarly-numbered WH23X29538 valve — confirm you have the correct number before ordering. Common Problems This Part Fixes Washer not filling with water, or filling only partially Washer fills much more slowly than it used to Water leaking near the valve connections Cycle stalling at the fill step and never advancing to wash No hot water reaching the tub, or no cold water reaching the tub Washer not washing properly due to insufficient or incorrect-temperature water Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: WH23X29553, 33090202, C-491/20-A13, AGE26162, AP6983554, EAP12743643, PD00067381, PS12743643 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select GE front-load washers, and also fits select Hotpoint, RCA, Haier, Monogram, and Café washers built on the GE platform, including model numbers such as: GFW650SPN0SN, GFW650SPN1SN, GFW650SPN2SN, GFW650SPN3SN, GFW650SPN4SN GFW650SSN0WW, GFW650SSN1WW, GFW650SSN2WW, GFW650SSN3WW, GFW650SSN4WW GFW850SPN0DG, GFW850SPN0RS, GFW850SPN1DG, GFW850SPN1RS, GFW850SPN2DG, GFW850SPN2RS, GFW850SPN3DG, GFW850SPN3RS, GFW850SPN4RS, GFW850SPN5RS GFW850SSN0WW, GFW850SSN1WW, GFW850SSN2WW, GFW850SSN3WW GFW655SSV0WW PFW870SPV0RS PFW950SPT0DS, PFW950SPT1DS, PFW950SPT2DS Note — not the same as WH23X29538: A similarly-numbered valve, WH23X29538, is a separate part (replaces 4977241, AP6990115, PS16217225, EAP16217225, 33090201, 0024000126GB) used on related but distinct models. The two are easy to confuse given how close the numbers are — always confirm you have the exact part number from your appliance or parts diagram before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement built to match GE's factory-specified solenoid design and flow rate ABS plastic body with stainless steel components for corrosion resistance Resolves "won't fill," "fills slowly," and "leaking near the valve" symptoms caused by valve failure Direct drop-in replacement — matches the original mounting and hose connections Replaces AP6983554, PS12743643, EAP12743643, 33090202, and 0024000126GA Compatible with GE, Hotpoint, RCA, Haier, Monogram, and Café front-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPWH23X29553 Part Type Washer Water Inlet Valve OEM Part Number WH23X29553 Condition Aftermarket Replacement Brand GE Application Front-Load Washers Body Material ABS plastic Component Material Stainless steel Quantity 1 valve Compatible Brands GE, Hotpoint, RCA, Haier, Monogram, Café Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Release The Control Panel Carefully Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Access to this valve is typically behind the front control panel on many models. When removing the front control panel, avoid pulling it straight out too far — slotted tabs on the right side of the panel can break if forced. Instead, pull the panel gently forward, then slide it to the right to release it cleanly. With the panel released, locate the valve and disconnect the hot and cold water supply hoses, keeping a towel handy for residual water. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the outlet hoses from the old valve, remove its mounting screws, and pull it free. Install the new WH23X29553 in the same position, reconnect all outlet hoses to their original positions, reconnect the electrical connector, and secure the mounting screws. Reattach the hot and cold supply hoses, tightening securely. Reinstall the control panel and any surrounding trim, restore the water supply, and check every connection for leaks before restoring power. Run a full test cycle across a few different temperature settings to confirm each fill function works correctly. Tools needed: Phillips screwdriver, pliers, towel, work gloves. Frequently Asked Questions How do I remove the front control panel without breaking it? Avoid pulling the panel straight out with heavy force — the slotted tabs on the right side of the panel can snap if you pull too far. Instead, pull the panel gently forward first, then slide it to the right to release it from its mounting. This gentler approach avoids the most common way this panel gets damaged during a valve repair. I've heard this valve sometimes needs replacing again after just a couple of years. Is that normal? Some owners have reported needing to replace this valve again within a relatively short time, even after a successful repair. While most installations hold up well long-term, if you experience a repeat failure, it's worth double-checking your household water pressure and mineral content, since hard water and high pressure can accelerate wear on any water valve regardless of brand. Is this the same as WH23X29538? The numbers look almost identical. No, these are two separate GE valve part numbers with different cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close match, since ordering the wrong one means it won't fit correctly. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the solenoid design, flow rate, and connection type of the original WH23X29553 valve used in compatible GE, Hotpoint, RCA, Haier, Monogram, and Café front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11248040 Washer Console (Control Panel Housing) Genuine Whirlpool part Replaces Part Number W11248040, 4845509, W11035013, W11120176, W11192407, PD00087512, EAP12584120, AP6783239, PS12584120. Model Cross Reference This part #W11248040 works with all models listed. Kenmore / Sears 110.27132412 Washer Kenmore / Sears 110.27132413 Washer  

Read more less