Search results for "refrigerator switch"

XPARTCO DC97-15459G Washer Water Valve  The XPARTCO DC97-15459G is an aftermarket replacement water inlet valve assembly compatible with a wide range of Samsung top-load washers. This valve mounts at the rear of the washer and controls the flow of water into the drum, opening electronically when the control board calls for a fill and closing once the target water level is reached. It connects via five terminal connections to the wiring harness and to the hot/cold supply hoses. When this valve fails, the washer commonly won't fill with water, fills very slowly, overfills, or continues to trickle water even when powered off — the last of which points to a valve that isn't sealing properly rather than an electrical fault. It directly replaces DC97-15459G, 3276197, AP5623056, ASM1220342, EAP4220861, PD00007887, PS4220861. Sold individually; does not include wire harness or mounting screws. Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO DC97-15459G Washer Water Valve fixes Samsung top-load washers that won't fill, fill slowly, overfill, or leak/drip water even when the washer is unplugged. 5-terminal connection for wiring and hot/cold hose lines. Sold individually — wire harness and mounting screws not included. Replaces DC97-15459G, 3276197, AP5623056, ASM1220342, EAP4220861, PD00007887, PS4220861. Classic symptom: washer trickles water into the drum even when it's completely powered off. Common Problems This Part Fixes Washer won't fill with water at all Washer fills very slowly or takes much longer than normal Washer overfills or keeps adding water past the normal level Water trickles or leaks into the drum even when the washer is off Leaking or dripping at the water inlet connection point Error code related to water fill or water level on the display Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: DC97-15459G, 3276197, AP5623056, ASM1220342, EAP4220861, PD00007887, PS4220861 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with a wide range of Samsung top-load washers, including: Samsung WA45H7200AP/AW, WA48H7400AP/AW, WA48J7770AP/AW Samsung WA50F9A6/7/8 series, WA50K8600AW, WA50M7450AP/AW Samsung WA52J8700AP/AW, WA52M7750AV/A4 and related WA52M7750 series Select Kenmore washers (Samsung-built models) Note: This valve is sold individually and does not include the wire harness or mounting screws — reuse your existing hardware during installation. Always verify your appliance model number before ordering. Contact our support team with your model number if you're unsure. Key Features Direct-fit replacement Samsung washer water inlet valve assembly Resolves "won't fill," "slow fill," "overfilling," and "leaking when off" symptoms Electronically controlled valve opens/closes based on control board signal 5-terminal connection for wiring harness and hot/cold hose lines Replaces DC97-15459G, 3276197, AP5623056, ASM1220342, EAP4220861, PD00007887, PS4220861 Compatible with a wide range of Samsung top-load washer models Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number XPDC97-15459G OEM Part Number DC97-15459G Part Type Washer Water Inlet Valve Assembly Condition Aftermarket Replacement Terminals 5-terminal wiring/hose connection Sold As Individually (wire harness and screws not included) Application Samsung Top-Load Washer Water Supply Compatible Brands Samsung, Kenmore Installation Notes ⚠️ Shut Off Water Supply and Unplug Washer Before Starting Turn off both the hot and cold water supply valves and disconnect power to the washer before beginning. Pull the washer away from the wall for access to the rear panel. Disconnect the hot and cold water supply hoses from the old valve — have a towel ready to catch residual water. Photograph the wiring before disconnecting, then unplug the wire harness connectors from the old valve. Remove the mounting screws holding the valve to the cabinet and remove the old valve. Install the new DC97-15459G valve in the same position using your existing mounting screws (not included with this part) and reconnect the wire harness, matching your photos. Reconnect the hot and cold supply hoses, making sure they're threaded onto the correct ports. Turn the water supply back on and check for leaks at the hose connections before restoring power. Run a test cycle to confirm the washer fills correctly and doesn't leak. Tools needed: adjustable pliers or channel locks (for hose connections), Phillips and flat-head screwdrivers. Frequently Asked Questions My washer trickles water into the drum even when it's unplugged — is this the part? Yes, this is a classic symptom of a water inlet valve that isn't sealing properly. Since the valve is the only thing standing between your home's pressurized water supply and the drum, a valve that won't fully close will let water trickle through even with zero power to the washer. This is different from an electrical fill problem, which typically shows up as the washer not filling at all rather than filling when it shouldn't. Does this include the wire harness and mounting screws? No — this valve is sold individually. You'll reuse your existing wire harness connector and mounting screws from the old valve during installation. Will this fit my Kenmore washer? This valve fits select Kenmore washers that were built by Samsung and share this platform's water valve design. Confirm your appliance model number before ordering, since not all Kenmore washers use this valve. Do I need to shut off the water supply to replace this? Yes — always shut off both the hot and cold water supply valves before disconnecting the hoses from the old valve. Skipping this step will result in water spraying from the open supply lines once the hoses are disconnected. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WE4X800 Dryer Genuine OEM Thermostat Replaces Part Numbers: WE4X800, 2285, AH268245, EA268245, ET800, WE04X0730, WE04X0800, WE4X730, OEM10477750, AP2619437, PS268245. Description: This Thermal Cut-Off Kit is a Genuine OEM part for specific GE dryer models. This safety kit is designed to protect the dryer from overheating by interrupting the heat source when the dryer air temperature reaches dangerously high levels.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WB15X27280 Genuine OEM GE Oven Door Handle and End Cap Assembly — Stainless Steel The WB15X27280 is a genuine GE OEM oven door handle and end cap assembly, finished in stainless steel, for GE ranges. This is the bar you grip every time you open or close the oven door, along with the two end caps that anchor it securely to the door frame. It's a simple mechanical part, but it takes a lot of repeated stress and impact over years of daily cooking, which is exactly why it's a common wear item. The handle measures 27.5 inches long. Over time, frequent use, exposure to high oven temperatures, and accidental impact can loosen, crack, or bend the handle or its end caps, making the door harder or less safe to operate. This is sold as a complete assembly — the handle bar and both end caps come together as one part and are not available individually, since the caps are what secure the handle to the door and the two are engineered as a matched set. It directly replaces AP6030812, WB15T10222, 4456008, and PS11762365. Quick Answer The WB15X27280 Genuine OEM GE Oven Door Handle and End Cap Assembly fixes GE, Hotpoint, RCA, and select Kenmore ranges with an oven door handle that's loose, cracked, wobbly, or has a broken or missing end cap. Stainless steel finish, 27.5" long. Replaces AP6030812, WB15T10222, 4456008, PS11762365. Sold only as a complete assembly — the handle and end caps are not available separately, even if only one end cap has failed. Common Problems This Part Fixes Oven door handle feels loose or wobbly when gripped Handle has cracked, bent, or broken End cap is cracked, broken, or missing entirely Handle has separated or come loose from the door frame Difficulty safely opening or closing the oven door Visible discoloration or heat damage on the handle or end caps Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This oven door handle and end cap assembly directly replaces the following OEM and cross-reference part numbers: WB15X27280, WB15T10222, AP6030812, AGE21582, 4456008, EAP11762365, PD00032591, PS11762365 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This handle and end cap assembly is compatible with select GE ranges, and also fits select Hotpoint, RCA, and Kenmore ranges built on the GE platform. Note — sold as a complete assembly only: The handle bar and end caps for this part are not sold separately, even if only one end cap or only one side has failed — you'll need to replace the complete WB15X27280 assembly. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified fit, finish, and mounting Complete assembly — handle bar and both end caps included as a matched set Resolves "loose or wobbly handle," "cracked or broken handle," and "missing or broken end cap" symptoms Stainless steel finish for durability and a clean, matching appearance 27.5" handle length Direct drop-in replacement for the original door-mounted handle Replaces WB15T10222, AP6030812, 4456008, and PS11762365 Compatible with GE, Hotpoint, RCA, and select Kenmore ranges Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WB15X27280 Part Type Oven Door Handle and End Cap Assembly Condition Genuine OEM Brand GE Finish Stainless steel Handle Length 27.5 in. Kit Contents Handle bar + 2 end caps (sold as one assembly) Repair Difficulty Moderate — inner door panel removal required Quantity 1 handle and end cap assembly Compatible Brands GE, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Unplug Range Or Shut Off Breaker Before Starting — Support The Door While Working Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Open the oven door and locate the screws along the bottom edge of the door — typically four screws securing the inner door panel. Remove these screws, then carefully remove the inner door panel to expose the screws that hold the handle assembly in place from behind. Photograph the mounting hardware and orientation before removing the old handle. Remove the screws securing the old handle and end caps, and lift the assembly free. Position the new WB15X27280 assembly in the same orientation, secure it with the mounting screws, and reinstall the inner door panel with its bottom screws. Close and open the door a few times to confirm the handle feels solid with no wobble before returning the oven to normal use. Tools needed: Phillips or nut driver screwdriver, work gloves. Frequently Asked Questions Can I just replace one end cap instead of the whole handle? No. GE does not sell the end caps or the handle bar separately for this part — WB15X27280 is sold only as the complete assembly. Even if just one end cap has cracked or broken while the handle bar itself is fine, you'll need to order the full assembly to make the repair. How do I access the handle to replace it? Start at the bottom edge of the oven door, where you'll find screws (typically four) securing the inner door panel. Remove those screws and take off the inner panel, which exposes the screws holding the handle assembly in place from behind. From there, removing the old handle and installing the new one is straightforward. My handle is curved — can I get a flat one instead? This assembly is designed to match your oven's original handle shape and mounting points, so it replicates the curved profile if that's what your model originally came with. A differently shaped handle isn't offered as a substitute for this part number, since the end caps and mounting points are engineered specifically for the original handle's geometry. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original stainless steel finish, length, and mounting configuration of the handle and end cap assembly originally installed on your range. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM WPW10140917 Washer Water Inlet Valve with Vacuum Break The Genuine OEM Whirlpool WPW10140917 is the water inlet valve with vacuum break for select Whirlpool-built washers, including Maytag, Kenmore, Amana, Inglis and other brands. The valve regulates water intake for wash cycles and delivers water into the washer drum, and the vacuum break helps keep wash water from backing up into the supply. When the valve fails, the washer may leak, and fill problems can follow. This is the original Whirlpool part, not an aftermarket equivalent. Check your model number before ordering. Quick Answer The Genuine OEM WPW10140917 Water Inlet Valve replaces the water inlet valve on a compatible Whirlpool-built washer when it leaks or no longer controls water intake correctly. Replaces W10140917. Classic symptom: water leaking at the valve. Common Problems This Part Fixes Water leaking at the inlet valve Water inlet valve not controlling water intake correctly Washer not filling or filling incorrectly because of a failed valve Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This water inlet valve replaces or supersedes the following part numbers: WPW10140917, W10140917, OEM18047055, AP6015682, AWP49689, EAP11748963, PD00003949, PS11748963 Whirlpool sells similar valves under nearby numbers, such as WPW10140918, which are not interchangeable by number alone. If your old valve shows a different number, contact our support team and we'll check whether it matches. Compatibility This water inlet valve is listed for Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Inglis, Jenn-Air, Magic Chef and Crosley washers, including these examples: WTW5100VQ1, WTW5100VQ2, WTW5300SQ2, 1CWTW5100VQ1 CAWS9234VQ0, ETW4400VQ3, NTW4500VQ1 ITW4300SQ3, IV45001, IV4500X0 Note: The models above are a small sample, not a full list. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool part, not an aftermarket equivalent Water inlet valve with vacuum break Regulates water intake and delivers water into the washer drum Sold as one complete valve Product Specifications Part Number WPW10140917 OEM Part Number WPW10140917 Part Type Washer Water Inlet Valve with Vacuum Break Condition Genuine OEM Manufacturer Whirlpool Application Select Whirlpool-Built Washers Installation Notes ⚠️ Unplug Power And Shut Off Water Before Installing Unplug the washer and turn off the water supply before you begin, and wear protective gloves. Access to the valve is typically through the back panel or the control panel, depending on the model. Note where each hose and wiring connector goes, disconnect them, remove the old valve, and fit the new valve in the same position. Reconnect everything, restore water and power, and run a short cycle while checking for leaks. Frequently Asked Questions My washer is leaking at the valve. Is this the part I need? If the leak is coming from the water inlet valve itself, replacing the valve is the repair. Check the supply hoses and their connections first, since a loose or worn hose can leak in the same area. Is this an OEM or aftermarket part? This is a genuine OEM part from Whirlpool, not an aftermarket equivalent. Can I use a valve with a similar part number? Not by number alone. Whirlpool sells several water inlet valves with similar numbers for different washers. Match the part number and your model number, or contact our support team and we'll check for you. Will this fit my washer? It is listed for many Whirlpool-built washers, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

EXP652 Dryer Belt and Idler Pulley Replaces WPW10112954, 279640 The EXP652 is an aftermarket replacement drum belt and idler pulley kit for Whirlpool and Maytag electric and gas dryers, and also fits select KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. These two components work together: the drum belt circles the drum and attaches to the motor pulley to transmit rotation, while the idler pulley rides against the belt to maintain proper tension so it doesn't slip or sag during operation. Because these two parts share the same drive path and tend to wear on a similar timeline, they're commonly sold and replaced together. Symptoms of failure include the dryer not starting, the drum not tumbling or spinning, and noise issues such as squealing or rubbing during operation. It directly replaces W10112954, WPW10112954, AP6015116, PS11748388 (drum belt), and AP3094197, PS334244, 279640, and 3388674 (idler pulley). Quick Answer The EXP652 Dryer Belt and Idler Pulley fixes Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore electric and gas dryers that won't start, won't tumble or spin, or make squealing/rubbing noise. Includes drum belt and idler pulley. Replaces W10112954, WPW10112954, AP6015116, PS11748388, AP3094197, PS334244, 279640, 3388674. These two parts wear together — replacing both at once, rather than just the one that failed, helps avoid reopening the dryer again soon after. What's In The Kit Component Replaces Function Drum Belt WPW10112954 / W10112954 Circles the drum and attaches to the motor pulley to transmit rotation and keep the drum tumbling. Idler Pulley 279640 Rides against the belt to maintain proper tension so it doesn't slip or sag. Common Problems This Kit Fixes Dryer won't start Drum won't tumble or spin Squealing or rubbing noise during operation Belt slipping or sagging, causing inconsistent tumbling Extended or inconsistent drying times Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer belt and idler pulley kit directly replaces the following OEM and cross-reference part numbers: Belt Replaces Part Numbers WPW10112954, W10112954, 1447719, AP6015116, AWP48873, EAP11748388, PD00003553, PS11748388 Idler Pulley Replaces Part Numbers 279640, 279640VP, 2958, 3388672, 697692, TJ279640, W10468057, AH334244, EA334244, ER279640, AWP39098, PD00002356, EAP334244, AP3094197, PS334244. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This kit is compatible with select Whirlpool electric and gas dryers, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryers built on the Whirlpool platform, including model numbers such as MED8000AG0, MED8000AW0, MGD6000XW0, MGD6000XW1, MGD6000XW2, MGD8000AG0, MGD8000AG1, MGD8000AW0, MGD8000AW1, 4KMEDC300BW0, 7MMGD0100TQ1, and MGD5500FC0. Note: Whirlpool also uses a different idler pulley, W10837240, on other dryer models — this kit specifically pairs the WPW10112954 belt with the 279640 idler pulley. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement kit — drum belt and idler pulley in one purchase Resolves "won't start," "won't tumble or spin," and "squealing/rubbing noise" symptoms Restores smooth drum rotation with proper belt tracking and tension Reduces noise and vibration from a worn belt or pulley Direct drop-in replacement matching the original belt length and pulley mounting Replaces W10112954, WPW10112954, AP6015116, PS11748388, AP3094197, PS334244, 279640, and 3388674 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore electric and gas dryers Built to OEM-equivalent quality standards Product Specifications Part Number EXP652 Set Contents 1x Drum Belt (replaces WPW10112954), 1x Idler Pulley (replaces 279640) Condition Aftermarket Replacement Application Whirlpool / Maytag Electric and Gas Dryers Belt Length Approx. 92-1/2" Belt Profile Flat, 5 ribs, 4 grooves Related Idler Pulley W10837240 (for other models, sold separately) Repair Difficulty Moderate — front/top panel and drum removal required Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — This Is A Bigger Repair Requiring Significant Disassembly Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Remove the top and front panels of the dryer, then the drum, to access the belt and idler pulley. Remove the old drum belt from around the drum and motor pulley. Remove the old idler pulley from its mounting bracket. Install the new EXP652 idler pulley in the same position, making sure it spins freely by hand before continuing. Route and install the new drum belt correctly around the drum and motor pulley, matching the original path exactly, and re-tension it through the idler pulley. Reinstall the drum, then reassemble the front and top panels. Restore power and run a test cycle to confirm quiet, smooth operation with the drum tumbling normally and no squealing or rubbing noise. Tools needed: nut driver, Phillips screwdriver, work gloves. Frequently Asked Questions My dryer's motor runs but the drum won't turn. Is this the right kit? Yes, this is the classic symptom addressed by a worn or broken drum belt, and since the idler pulley works together with the belt to maintain proper tension, replacing both at once addresses the most common causes of this problem in one repair. Do I need to replace both parts, or just the one that failed? You can replace just the failed component if you've confirmed which one is actually bad, but these two parts share the same drive path and tend to wear out around the same time — a worn pulley can accelerate belt wear, and a worn belt puts extra strain on the pulley. Replacing both together, since you'll already have the dryer largely disassembled for access, helps avoid a second teardown soon after. Is this the same idler pulley as your other Whirlpool dryer belt kits? Not necessarily — Whirlpool uses more than one idler pulley design across its dryer lineup. This kit specifically pairs the WPW10112954 belt with the 279640 idler pulley. Other kits may pair the same belt with a different pulley, such as W10837240, used on other models. Always confirm your full model number before ordering. Is this an OEM or aftermarket part? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the belt length, rib pattern, and pulley design of the original WPW10112954 belt and 279640 idler pulley used in compatible Whirlpool, Maytag, and related electric and gas dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WD15X26078 Genuine OEM GE Dishwasher Water Inlet Valve The WD15X26078 is a Genuine OEM GE replacement dishwasher water inlet valve compatible with a wide range of GE, GE Profile, Café, Haier, Hotpoint, RCA, and Kenmore GE-built dishwashers. The water inlet valve is mounted at the base of the dishwasher behind the lower access panel, connecting the household water supply line to the dishwasher's fill circuit. When the control board calls for water during the fill phase, the valve's internal solenoid opens, allowing water to flow into the tub — and it closes the instant the call is dropped, stopping flow precisely at the correct fill level. Without a properly functioning inlet valve, the dishwasher can't fill correctly — leading to poor cleaning performance, error codes, or no wash at all. Rated 120V, 60Hz. Approximate dimensions: 3.75" H x 3.25" W x 3.00" L. Silver/multi-color metal and plastic construction with a deep-threaded, high-quality water inlet for a tight supply-line connection and a secure outlet design that keeps the internal fill hose firmly attached. As a Genuine OEM part manufactured by GE to factory specifications, the WD15X26078 directly replaces 4959029, AP6986683, PS16217027, EAP16217027, and PD00064270. Hard water sediment is a leading cause of inlet valve clogging and failure on GE dishwashers — if your old valve is restricted by mineral buildup, replacement (not cleaning) is the recommended fix, as the internal components are easily damaged during cleaning attempts. Installs in 20–30 minutes with basic hand tools. Quick Answer The WD15X26078 Genuine OEM GE Dishwasher Water Inlet Valve fixes GE, GE Profile, Café, Haier, Hotpoint, and Kenmore dishwashers that aren't filling with water, fill slowly, display the H2O error code, make strange noises or vibration during fill, won't stop filling, or leak from the valve area. 120V, 60Hz. Approx 3.75"H x 3.25"W x 3.00"L. Genuine OEM GE. Replaces 4959029, AP6986683, PS16217027, EAP16217027, PD00064270. Compatible with GDF, GDT, GDP, PDT, PDP, QDP, ZDT, DDT, and Café CDT series dishwashers. Common Problems This Part Fixes Dishwasher not filling with water at all — valve solenoid not opening Dishwasher filling slowly or not getting enough water — valve clogged with hard water sediment H2O error code displayed — insufficient water intake detected Strange noises or vibration during the fill phase — worn valve diaphragm Dishwasher won't stop filling — valve stuck open (overfill/flood risk) Water leaking from the valve area or its connections Dishes not being cleaned properly due to insufficient water fill Wash cycle interrupted or extended due to fill timeouts Valve inlet screen visibly clogged with mineral deposits Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers: WD15X26078, AGE846049, AP6986683, EAP16217027, PD00064270, PS16217027 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: some similar-looking GE valves (such as WD15X24213 or WD15X26140) are different parts — verify your original valve's part number or your dishwasher model number before ordering. Compatibility This water inlet valve is compatible with select dishwashers from the following brands: GE dishwashers — GDF series (GDF510PGM4BB/WW, GDF510PSM4SS/5SS, GDF511PSM5SS, GDF511PGM5WW, GDF530PGM4BB/CC/WW/5WW, GDF530PSM4SS/5SS, GDF530PMM4ES, GDF565SSN3SS, GDF630PFM4DS/5DS, GDF630PGM4BB/WW/5BB, GDF630PMM4ES/5ES, GDF630PSM4SS, GDF640HFM4DS, GDF640HGM4WW/5BB, GDF640HMM4ES, GDF645SGN2BB/WW/3BB/3WW, GDF645SMN2ES/3ES, GDF645SSN2SS/3SS and related) GE dishwashers — GDT series (GDT530PGP5BB, GDT530PSP5SS, GDT535PSMASS, GDT535PSM5SS, GDT565SSN2SS, GDT605PSM5SS, GDT630PFM4DS, GDT630PMM4ES/5ES, GDT630PYM4FS, GDT635HMM4ES, GDT635HSM4SS/5SS, GDT645SGN2BB/WW/3WW, GDT645SMN3ES, GDT645SSN2SS, GDT645SYN2FS, GDT665SBN2TS/3TS, GDT665SFN3DS, GDT665SGN2WW/3WW, GDT665SMN2ES, GDT665SSN3SS and related) GE dishwashers — GDP series (GDP615HFM4DS, GDP645SYN3FS/4FS/8FS, GDP665SYN2FS/3FS/4FS/8F7S and related) GE Profile dishwashers — PDT series (PDT715SBN2TS/3TS, PDT715SFN3DS, PDT715SMN2ES/3ES, PDT715SYN3FS, PDT775SYN2FS/3FS, PDT785SBN2TS, PDT785SYN2FS/3FS/5FS and related) GE Profile dishwashers — PDP series (PDP715SBN3TS, PDP715SYN3FS and related) GE dishwashers — QDP series (QDP555SBN4TS, QDP555SYN4FS and related) GE Monogram dishwashers — ZDT series (ZDT925SIN2II/3II/5II, ZDT925SPN2SS/3SS, ZDT925SSN2SS/3SS/5SS, ZDT985SIN3II, ZDT985SPN5SS, ZDT985SSN5SS and related) GE dishwashers — DDT series (DDT700SBN2TS/3TS, DDT700SFN2DS/3DS, DDT700SGN2BB/WW, DDT700SMN2ES and related) Café dishwashers — CDT series (CDT800P2N2S1-N5S1, CDT805M5N2S5-N4S5, CDT805P2N2S1-N5S1, CDT845M5N2S5-N5S5, CDT845P2N2S1-N5S1, CDT845P3N2D1-N5D1, CDT845P4N2W2-N5W2, CDT855M5N2S5/N3S5/N5S5, CDT855P2N2S1/N3S1/N5S1, CDT875M5N2S5-N7S5, CDT875P2N2S1-N5S1, CDT875P3N5D1 and related) Haier dishwashers (select models using the GE-platform valve) Hotpoint and RCA dishwashers (select GE-built models) Kenmore / Sears dishwashers (select GE-built models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Controls the flow of water into the dishwasher during fill cycles — precise fill for optimal cleaning performance Solenoid-actuated — opens when the control board calls for water and closes the moment the call is dropped Rated 120V, 60Hz — correct electrical specifications for compatible GE-platform dishwashers Approximate dimensions: 3.75" H x 3.25" W x 3.00" L Deep-threaded water inlet for a tight, leak-free supply line connection Secure outlet design keeps the internal fill hose firmly attached Resolves H2O error codes, no-fill, slow-fill, overfill, and fill-noise symptoms Replaces 4959029, AP6986683, PS16217027, EAP16217027, and PD00064270 Compatible with GE GDF/GDT/GDP series, GE Profile PDT/PDP series, QDP series, Monogram ZDT series, DDT series, Café CDT series, plus Haier, Hotpoint, RCA, and Kenmore GE-built dishwashers DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WD15X26078 Part Type Dishwasher Water Inlet Valve Assembly Condition Genuine OEM Application Dishwashers (GE platform) Voltage 120V AC Frequency 60 Hz Dimensions Approximately 3.75" H x 3.25" W x 3.00" L Color Silver / Multiple Colors Material Metal / Plastic Error Codes Resolved H2O (insufficient water intake) Compatible Brands GE, GE Profile, Café, Monogram, Haier, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power at the breaker and shut off the household water supply at the shutoff valve under the sink before beginning. Wear work gloves to protect your hands. Have towels and a shallow dish ready — residual water remains in the supply line and hoses and will spill when disconnected. Remove the lower access panel (baffle) at the front bottom of the dishwasher — typically 2–4 screws. Locate the water inlet valve where the household supply line enters the dishwasher. Photograph the hose and wire connections before disconnecting anything. Disconnect the household water supply line from the valve inlet (use pliers for the larger ingress connection — place the dish underneath to catch leftover water). Disconnect the internal fill hose from the valve outlet (needle-nose pliers help with the smaller egress hose clamp). Unplug the electrical connector that snaps onto the valve solenoid. Remove the mounting screws holding the valve bracket to the frame and lift the old valve out. Install the new WD15X26078 valve in the same position, secure the mounting screws, reconnect the internal fill hose with its clamp, and snap the electrical connector back on. Reconnect the household water supply line to the valve inlet — align the threads carefully and tighten snugly without over-torquing. Turn the water supply back on and use a flashlight to inspect all connections for leaks BEFORE reinstalling the access panel. Restore power and run a test cycle to confirm proper filling with no leaks. Tools needed: Phillips screwdriver, pliers, needle-nose pliers, shallow dish, towels, flashlight, work gloves. Frequently Asked Questions What does the H2O error code mean on my GE dishwasher? The H2O error code on GE dishwashers indicates the control board is not detecting sufficient water intake during the fill phase. Common causes are: a failed or clogged water inlet valve (the most frequent culprit), the household water supply shutoff valve partially closed, a kinked supply line, or low household water pressure. First verify the supply valve under the sink is fully open and the line isn't kinked. If the supply checks out, the WD15X26078 inlet valve is the standard fix — hard water sediment gradually clogs the valve's internal screen and passages, restricting flow until the dishwasher can't fill within its expected time window. Can I clean the old valve instead of replacing it? It's not recommended. While the inlet screen on some valves can be carefully brushed clean, the internal passages and solenoid diaphragm of a sediment-clogged valve are easily damaged during cleaning attempts — a common outcome is a valve that leaks or sticks open after being "cleaned," which risks flooding. Real-world experience (including customer stories with this exact part) shows that attempting to clean a hard-water-clogged valve often breaks it. Given the moderate cost of the OEM replacement versus the flood risk of a compromised valve, replacement is the reliable repair. If your area has hard water, consider this a maintenance item that may need periodic replacement. My dishwasher won't stop filling — is that also this valve? Yes — a valve stuck in the open position is the other failure mode. When sediment or a worn diaphragm prevents the valve from sealing fully closed, water continues to flow into the tub even when the control board has cut power to the solenoid. This can lead to overfilling and potentially flooding through the door or float overflow. If your dishwasher keeps filling past its normal level, or you find water accumulating in the tub between cycles, shut off the water supply at the sink immediately and replace the valve before running the dishwasher again. How do I know this is the right valve for my GE dishwasher? Check your dishwasher's model number (on a label along the door frame or tub edge) against the compatibility list above — the WD15X26078 covers a broad range of GE GDF, GDT, GDP, Profile PDT/PDP, QDP, Monogram ZDT, DDT, and Café CDT series dishwashers. Be aware that some similar-looking GE valves (such as WD15X24213 or WD15X26140) are different parts used on other model groups — they are not interchangeable with the WD15X26078. If your model isn't in the list or your original valve shows a different part number, contact our support team with your model number and we'll verify the correct valve before you order. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same water inlet valve installed in compatible GE, GE Profile, Café, Monogram, Haier, Hotpoint, RCA, and Kenmore GE-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11366438 Range Surface Burner Knob Product Overview The XPARTCO W11366438 Range Surface Burner Knob is designed to control the heat level of your stove burners with precision. This high-quality replacement knob restores smooth operation and enhances the appearance of your cooktop. Quick Answer If your stove knob is cracked, loose, missing, or difficult to turn, the W11366438 burner knob is likely worn out. Replacing it restores proper burner control and usability. Replaces Part Numbers Replaces OEM part number: W11366438, W11084623, 4929319, W11359382, W11505414, EAP12723935, AWP44385, PD00054489, AP6888134, PS12723935. Compatibility This surface burner knob is compatible with select Whirlpool, Maytag, and other compatible ranges. Whirlpool Ranges Maytag Ranges Always verify your appliance model number before ordering. Common Problems This Part Fixes Broken or cracked knob Knob slipping or not engaging Missing control knob Difficulty adjusting burner heat Key Features Restores precise burner control Easy push-on installation High-quality aftermarket replacement Durable construction for daily use Product Specifications Part Number: XPW11366438 Part Type: Range Surface Burner Knob Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Range Burner Control Troubleshooting Guide Knob spins freely → Worn insert Cannot adjust flame → Damaged knob Knob falls off → Cracked fitting When Should You Replace This Knob? Replace this knob if it is cracked, loose, missing, or not functioning properly. Installation Notes ⚠️ Ensure the appliance is off. Pull the old knob straight off and push the new knob firmly onto the control shaft. Related Parts Surface Burner Valve Igniter Switch Control Panel Overlay Frequently Asked Questions Will this knob fit my range?This knob fits many Whirlpool and compatible models. Always verify your model number. Is installation difficult?No, this knob is typically push-on and easy to install. What are signs of a bad knob?Cracks, slipping, or inability to control heat settings. Is this OEM or aftermarket?This is a high-quality aftermarket replacement part. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support

Read more less

ERP DC47-00015A Dryer Thermostat Fits Specific Samsung, Whirlpool Dryer models. non-resettable dryer thermostat. Description: This Dryer Thermal Fuse is a exact replacement Part that is situated on the heating element housing for specific Samsung, Whirlpool dryer models. It meticulously measures the air temperature within the dryer drum and adjusts the heat to maintain the optimal drying temperature. In situations where your dryer doesn't start, fails to dry clothes effectively, or doesn't produce heat, a faulty thermal fuse might be the cause. Replaces Part Numbers:DC47-00015A, 2068544, 35001091, 1122484, AH2038382, DC47-00015A, EA2038382, AP4201892, PS4205212, AP4045835, PS2038382. This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: California’s Proposition 65 

Read more less

W10245218 Genuine OEM Whirlpool Microwave Vent Grille (Black) The W10245218 is a genuine Whirlpool OEM vent grille for over-the-range microwaves, and also fits select Maytag, Jenn-Air, Kenmore, KitchenAid, Amana, Magic Chef, Admiral, Norge, and Roper models. Finished in black, this grille serves two purposes: it protects the microwave's internal components from physical impact and heat exposure, and it supports proper ventilation airflow to help prevent the unit from overheating. Weighing approximately 3.59 lbs, with package dimensions of 30.24" x 4.76" x 3.46". Common causes of failure include physical impacts, heat exposure over time, or general wear and tear from regular use — a common real-world failure is someone accidentally pulling or leaning on the grille, which can crack the plastic screw mounting tabs and leave the grille hanging loose or detached. Symptoms of a damaged grille include a cracked, broken, or hanging vent grille, or visible physical damage affecting either appearance or the ventilation airflow underneath. It directly replaces AP4411190, 1482738, AH2350384, EA2350384, and PS2350384. Quick Answer The W10245218 Genuine OEM Whirlpool Microwave Vent Grille (Black) fixes Whirlpool, Maytag, Jenn-Air, Kenmore, KitchenAid, Amana, Magic Chef, Admiral, Norge, and Roper over-the-range microwaves with a cracked, broken, or hanging vent grille. Black finish, approx. 30.24" x 4.76" x 3.46". Replaces AP4411190, 1482738, AH2350384, EA2350384, PS2350384. Whirlpool sells several similarly-numbered vent grilles in both black and white finishes for different models — always confirm your exact part number and color before ordering. Common Problems This Part Fixes Cracked or broken vent grille Grille hanging loose or detached from broken mounting tabs Visible physical damage to the grille's appearance Reduced ventilation airflow from a damaged grille Grille damaged by heat exposure or physical impact Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This microwave vent grille directly replaces the following OEM and cross-reference part numbers: W10245218, 1482738, AP4411190, AWP40654, PD00008076, EAP2350384, PS2350384 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This vent grille is compatible with select Whirlpool over-the-range microwaves, and also fits select Maytag, Jenn-Air, Kenmore, KitchenAid, Amana, Magic Chef, Admiral, Norge, and Roper microwaves built on the Whirlpool platform, including model numbers such as UMV1160CS6, UMV1160CB1, WMH1163XVB2, WMH1163XVQ1, WMH1163XVS1, WMH1164XWS1, WMH2175XVB2, WMH2175XVS2, WMH31017AS2, WMH31017AS3, WMH31017AW1, WMH31017FS0, WMH53520CS0, WMH53520CS2, WMH53520CS5, WMH76718AS0, YWMH76718AB0, GMH6185XVQ0, and GH5184XPS4. Note — several similar vent grilles exist: Whirlpool sells multiple vent grilles that can look nearly identical, including part number W10468664 and W10269471 (both white finish) and 8183948 (black finish, different part). This W10245218 is specifically the black-finish grille for its compatible models. Always verify your full model number and confirm the color and exact part number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified fit and black finish Protects internal microwave components from physical impact and heat exposure Supports proper ventilation airflow to help prevent overheating Resolves "cracked or broken grille" and "grille hanging loose" symptoms Approximately 30.24" x 4.76" x 3.46", 3.59 lbs Direct drop-in replacement matching the original mounting Replaces AP4411190, 1482738, AH2350384, EA2350384, and PS2350384 Compatible with Whirlpool, Maytag, Jenn-Air, Kenmore, KitchenAid, Amana, Magic Chef, Admiral, Norge, and Roper microwaves Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W10245218 Part Type Microwave Vent Grille Condition Genuine OEM Brand Whirlpool Application Over-the-Range Microwaves Color Black Weight Approx. 3.59 lbs Dimensions Approx. 30.24" x 4.76" x 3.46" Repair Difficulty Easy — basic hand tools Quantity 1 vent grille Compatible Brands Whirlpool, Maytag, Jenn-Air, Kenmore, KitchenAid, Amana, Magic Chef, Admiral, Norge, Roper Installation Notes ⚠️ Unplug Microwave Before Starting Unplug the microwave before beginning this repair. Wear work gloves to protect your hands. Locate the mounting screws or tabs securing the old vent grille in place, typically along the top or front edge of the unit depending on your model. Support the grille as you remove the mounting hardware, since a partially broken grille can shift or fall once released. Remove the old grille fully. Position the new W10245218 in the same location, aligning it with the mounting points, and secure it with the original screws or clips, taking care not to overtighten and crack the new plastic mounting tabs. Restore power and confirm the grille sits flush and securely in place with no gaps affecting the ventilation airflow. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My vent grille is cracked and hanging loose. What caused this? This is a common failure mode, often caused by someone accidentally pulling, leaning on, or bumping the grille — enough force can crack the plastic screw mounting tabs, leaving the grille hanging or detached even though the rest of the microwave is unaffected. One customer described exactly this scenario: a guest accidentally pulled on the top grille vent, cracking the plastic screw tap and leaving it hanging. How do I know I'm ordering the right color and part number? Whirlpool sells several vent grilles that look very similar across different models, in both black and white finishes. This W10245218 is specifically the black-finish version. Compare your old grille's color and check your full model number against the compatibility list, or check the part number printed on your old grille if it's visible, before ordering. Do I need any special tools to replace this grille? No, this is a straightforward repair with basic hand tools — typically just a Phillips screwdriver to remove and reinstall the mounting screws or clips holding the grille in place. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original black finish and mounting configuration of the vent grille originally installed on your microwave. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11688995 Genuine OEM Whirlpool Washer Water Inlet Valve (Cold) The W11688995 is a genuine Whirlpool OEM cold water inlet valve for Whirlpool-built front-load washers. Whirlpool's newer front-load platforms use two separate single-function valves instead of one combined hot/cold valve body — this cold-side valve handles only the cold water supply, while a matching hot-side valve (sold separately as W11688994) handles the hot side. When the control calls for a cold fill, it energizes this valve's solenoid coils to open the water path; when the correct level is reached, the valve closes again. If this valve fails to open, the washer won't take on cold water; if it fails to seal fully closed, water can trickle into the drum even when the washer isn't running. Because this is a dedicated single-function valve, a failure here shows up in a very specific way: cold-only fills stop working or slow down dramatically, while hot-only fills (governed by the separate W11688994 valve) continue working normally. Whirlpool's own service guidance links this valve to F8 E1 and LO FL fill-related error codes. Common failure modes include mineral or sediment buildup that prevents the valve from sealing, a burned-out solenoid coil, or a worn internal diaphragm. It directly replaces W11036930, W11316256, W11486361, AP7218603, PS17216730, and EAP17216730. As a genuine OEM part, the W11688995 is manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. Quick Answer The W11688995 Genuine OEM Whirlpool Washer Water Inlet Valve (Cold) fixes Whirlpool-built front-load washers where cold water won't fill, fills slowly, overfills, leaks into the drum when off, or throws an F8 E1 or LO FL error code. 120V, 50/60Hz, two-coil cold-only valve, 1/2" NPT threaded connections. Replaces W11036930, W11316256, W11486361, AP7218603, PS17216730, EAP17216730. This is the cold-side valve only — the companion hot-side valve is sold separately as W11688994. Common Problems This Part Fixes Washer won't fill with cold water while hot water fills normally Cold water fills much more slowly than it used to Washer overfills or takes on more water than the cycle calls for Water trickling or leaking into the drum on the cold side when the washer is off F8 E1 or LO FL error code displayed on the control panel Cycle stalling at the fill step and never advancing to wash Cold-wash or cold-rinse cycles specifically affected while warm/hot cycles run fine Water pooling underneath or behind the washer near the cold supply connection Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer cold water inlet valve directly replaces the following OEM and cross-reference part numbers: W11688995, W11316256, W11036930, W11486361, 4983050, PD00086086, FIX17216730, EAP17216730, OEM28874414, AP7218603, AWP46809, PS17216730. W11486361 and W11316256 were earlier Whirlpool numbers for this same valve, with W11036930 preceding those. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cold water inlet valve is compatible with select Whirlpool-built front-load washers across the Whirlpool family of brands, including: Whirlpool front-load washers — WFW series Maytag front-load washers — MHW and MFW series (select Whirlpool-built models) Amana front-load washers (select models) Inglis front-load washers — IFW series (select models) Select Kenmore front-load washers built on the Whirlpool platform Verified model numbers include: 8TWFC6810LW0 (laundry center), IFW5900HW0, IFW5900HW1, IFW5900HW2, IFW5900HW3, IFW5900HW4, MFW7020RF0, MFW7020RU0, MFW7020RW0, MHW5630HC0, MHW5630HC1, MHW5630HC2, MHW5630HC3, MHW5630HW0, MHW5630HW1, MHW5630HW2, MHW5630MBK0, MHW6630HC0 through MHW6630HC3, MHW6630HW0 through MHW6630HW3, MHW6630MBK0, MHW8630HC0 through MHW8630HC3, MHW8630HW0 through MHW8630HW3, WFW560CHW0, WFW560CHW1, WFW560CHW2, WFW5620HW0 through WFW5620HW3, WFW6620HC0 through WFW6620HC2, WFW6620HW0, WFW6620HW1, WFW8620HC0 through WFW8620HC4, WFW8620HW0 through WFW8620HW4, WFW862CHC0, and WFW862CHC1. Note — cold side only: This is the cold water valve. The matching hot water valve for these same washers is sold separately under part number W11688994. The two are not interchangeable — each is a dedicated single-function valve, and installing this cold valve in place of the hot valve (or vice versa) will not correctly control water temperature. If both valves need replacement, order both part numbers. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid, seal, and flow-rate design Dedicated cold-only water inlet valve — two internal coils control flow to the cold supply Resolves "won't fill with cold water," "fills slowly," "overfills," and "leaking into the drum" symptoms caused by valve failure Commonly resolves F8 E1 and LO FL error codes 1/2" NPT threaded connections for standard supply line hookups Direct drop-in replacement for W11036930, W11316256, and W11486361 Replaces W11036930, W11316256, W11486361, AP7218603, PS17216730, and EAP17216730 Compatible with Whirlpool, Maytag, Amana, Inglis, and select Kenmore front-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11688995 Part Type Washer Water Inlet Valve — Cold Condition Genuine OEM Brand Whirlpool Application Front-Load Washers (Whirlpool-Built) Voltage 120V Frequency 50/60 Hz Coils 2 (dedicated cold water function) Connection 1/2 in. NPT threaded Companion Part W11688994 (hot water valve, sold separately) Supersedes W11036930, W11316256, W11486361 Quantity 1 valve Compatible Brands Whirlpool, Maytag, Amana, Inglis, select Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Have A Towel Ready Unplug the washer or shut off its circuit breaker, and shut off both the hot and cold water supply valves before beginning. Wear work gloves. Disconnect the cold water supply line from the back of the valve first — have a towel or shallow pan ready, since residual water will spill out. Remove the rear screws securing the top panel, then slide the panel back and lift it off to access the valve assembly from inside the cabinet. Photograph the wiring connections before disconnecting anything, since the hot and cold valves sit side by side and it's easy to cross a wire. Disconnect the electrical connector from the old cold valve, remove its mounting screw or bracket, and pull the valve free — leave the hot valve (W11688994) undisturbed if it isn't also being replaced. Install the new W11688995 in the same position, secure the mounting screw, and reconnect the electrical connector fully. Reattach the cold water supply line, tightening securely by hand plus a partial turn with pliers — avoid overtightening plastic threaded fittings. Reinstall the top panel, restore the water supply, and check the connection for leaks before restoring power. Run a short cycle set to a cold wash and confirm the tub fills at the normal rate with no leaking underneath or behind the washer. Tools needed: 1/4" nut driver or socket, T-20 Torx bit, pliers, towel or shallow pan, work gloves. Frequently Asked Questions Cold water won't fill but hot water works fine. Is this the right part? Yes — that's exactly the symptom pattern this valve addresses. Because your washer uses two separate single-function valves rather than one combined valve, a fault on the cold side only affects cold fills while the hot valve (W11688994) keeps working independently. If cold-specific cycles are the ones failing, this cold valve is the correct part to replace. Do I need to replace both the hot and cold valves at the same time? Not necessarily. Since these are independent single-function valves, you only need to replace the one that has actually failed. If only cold fills are affected, replacing this W11688995 valve alone is sufficient. If both hot and cold fills are having problems, or if the valves are original and quite old, some people choose to replace both at once since they're already accessing the same area — but it's not required. My washer shows an F8 E1 or LO FL error. Does that mean this valve is bad? It's a strong indicator, but check the basics first. These codes generally mean the control didn't see water reach the expected level within its allotted fill time. Before replacing the valve, confirm the cold supply valve at the wall is fully open, check the inlet screen inside the valve port for sediment or debris, and make sure the cold fill hose isn't kinked. If those check out and cold water still won't fill properly, this valve is the likely cause. Can I use this valve on the hot water side instead? No. This is a dedicated cold-water valve, and the hot-water side uses a separate part number, W11688994. The two are built and calibrated for their specific supply line and are not interchangeable — installing the cold valve on the hot side (or vice versa) will not properly control water temperature during the cycle. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same two-coil solenoid design, seal, and flow-rate calibration as the cold water inlet valve originally installed in your front-load washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

5220FR2006H Washer Genuine OEM Water Inlet Valve (Hot) The 5220FR2006H is a genuine LG OEM hot water inlet valve for LG front-load washers, and also fits select Kenmore models. This valve connects to your home's hot water line and controls the flow of hot water into the tub during the fill portion of each cycle, opening as the cycle calls for hot water and closing once the correct fill level and temperature mix are reached. The valve has a standard hose fitting inlet and a single water outlet. Common causes of failure include mineral or sediment buildup inside the valve body and general electrical wear in the solenoid. Symptoms of a failing valve include the washer not filling, not stopping when it should, not starting, leaking water, not washing properly, no hot water reaching the tub, or an IE error code displayed on the control panel. It directly replaces 1268123, 5220FR1280F, 5220FR2006L, 5220FR2006Q, AP4441935, ALG51717, AH3527427, EA3527427, EAP3527427, PD00001765, PS3527427. Quick Answer The 5220FR2006H Washer Genuine OEM Water Inlet Valve (Hot) fixes LG and select Kenmore front-load washers with no hot water, won't fill, won't stop filling, won't start, leaking, or an IE error code. Standard hose fitting inlet, 1 outlet. Replaces 1268123, 5220FR1280F, 5220FR2006L, 5220FR2006Q, AP4441935, ALG51717, AH3527427, EA3527427, EAP3527427, PD00001765, PS3527427. This is the hot water valve — a separate but related cold water valve is used alongside it. If both valves are original and the same age, consider replacing both together while you have the washer open. Common Problems This Part Fixes No hot water reaching the tub Washer not filling with water Washer not stopping fill when it should Washer not starting Water leaking from the valve area IE error code displayed on the control panel Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer hot water inlet valve directly replaces the following OEM and cross-reference part numbers: 1268123, 5220FR1280F, 5220FR2006L, 5220FR2006Q, AP4441935, ALG51717, AH3527427, EA3527427, EAP3527427, PD00001765, PS3527427 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This hot water inlet valve is compatible with select LG front-load washers, and also fits select Kenmore washers built on the LG platform, including model numbers such as WM2240CW, WM2250CW, WM2277HW, WM3170CW, WM3250HV, 40272, 40441 (ABWESEU), 41002, 41003, 41172 (ABWEPEU), 41172 (ABWESEU), 41182, 41262 (ABWEPEU), 41262 (ABWEVEU), and 41283. Note: This is the hot water valve. Our 5220FR2008C listing is the related cold water valve, and our 5220FR2008F listing is a closely related water inlet and dispenser valve assembly used on other models — these are separate parts serving different roles or platforms. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which valve your washer needs. Key Features Genuine LG OEM part — factory-specified solenoid design and flow rate Regulates hot water flow into the tub during fill Resolves "no hot water," "won't fill," "won't stop filling," "won't start," "leaking," and "IE error code" symptoms Standard hose fitting inlet, 1 water outlet Direct drop-in replacement — matches the original mounting and hose connections Replaces 1268123, 5220FR1280F, 5220FR2006L, 5220FR2006Q, AP4441935, ALG51717, AH3527427, EA3527427, EAP3527427, PD00001765, PS3527427 Compatible with LG and select Kenmore front-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Simple 15-minute DIY repair Product Specifications Part Number 5220FR2006H Part Type Washer Hot Water Inlet Valve Condition Genuine OEM Brand LG Application Front-Load Washers Inlet Standard hose fitting Outlet 1 Related Part 5220FR2008C cold water valve (sold separately) Repair Difficulty Easy — approx. 15 minutes Quantity 1 valve Compatible Brands LG, Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting Turn off the water supply and unplug the washing machine from the wall before beginning. Wear work gloves. Locate the top cover of your washer — depending on your model, it may be located along the side or in the back — and use a flat-blade screwdriver to gently pry it off. Locate the hot water valve and disconnect the water supply hose from it, using locking pliers to loosen the hose clamp before carefully pulling the hose away. Unscrew the screws holding the valve in place and gently remove it from the washer. Mount the new 5220FR2006H valve in place and replace the screws. Reconnect the water supply hose to the valve and tighten the hose clamp using locking pliers. Turn the water supply back on and plug the washer back in. Test the new valve by running a load of laundry and checking for any leaks. Tools needed: flat-blade screwdriver, locking pliers, work gloves. Frequently Asked Questions My washer isn't getting hot water. Is this the part I need? Yes, this is the most direct symptom of a failed hot water inlet valve. Since this valve is what admits hot water from your household supply into the washer, a solenoid failure or internal blockage can prevent hot water from entering properly, even if cold water fill still works normally. My washer shows an IE error code. Could this valve be the cause? Yes, an IE error code on LG washers is commonly tied to a fill issue, and a failed inlet valve — hot or cold — is one of the most frequent causes. Confirm which side (hot or cold) is actually affected before ordering, since these are separate parts. Should I replace the cold water valve at the same time? It's worth considering, especially if both valves are the same age. One customer specifically purchased both the hot and cold water inlet valves together during a single repair, along with a new drain pump motor, rather than tackling each part separately over multiple repairs. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the hot water inlet valve originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

ERP 134793511 Dryer Idler Pulley Description: This Idler Arm Assembly is a replacement part for Specific Frigidaire clothes dryer models. It is a pulley assembly that helps to guide the dryer belt and keep it aligned. Replaces Part Numbers: 34793511, 134793500, 7134793500, AP6996178, PS16227173.    This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: California’s Proposition 65 

Read more less