XPARTCO W10350564 Refrigerator Run Capacitor Replaces WPW10350564
The XPARTCO W10350564 is an aftermarket replacement compressor run capacitor compatible with a wide range of Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Roper, Admiral, Ikea, and Kenmore refrigerators and freezers. The run capacitor is a small but critical electrical component mounted near the compressor at the back of the refrigerator — it delivers a phase-shifted power boost that helps the compressor motor start at the beginning of each cooling cycle, and supports smooth, efficient motor operation while the compressor runs. When the capacitor fails — typically from dielectric breakdown, age, heat, or moisture intrusion — the compressor may fail to start, hum without starting, kick on and off repeatedly, or cause inconsistent cooling throughout the refrigerator.
Rated 12 µF (MFD) ±5% capacitance, 180VAC, 50/60Hz. This capacitor works together with the compressor start relay/start device — the two components are frequently replaced together, since a failed capacitor often stresses the relay and vice versa. It directly replaces WPW10350564, W10350564, AP6020176, PS11753490, EAP11753490, and 2683570. This is one of the most cost-effective refrigerator repairs — a failed run capacitor mimics symptoms of a failed compressor (a far more expensive repair), so testing and replacing the capacitor first can save hundreds of dollars. Installs in about 15 minutes with basic hand tools.
Quick Answer
The XPARTCO W10350564 Refrigerator Run Capacitor fixes Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, and Kenmore refrigerators and freezers where the compressor won't start, hums without starting, kicks on and off, or the fridge/freezer is too warm with inconsistent cooling. 12 µF (MFD) ±5%, 180VAC, 50/60Hz. Replaces WPW10350564, AP6020176, PS11753490, EAP11753490, 2683570. Often replaced together with the compressor start relay. A 15-minute repair that can save you from misdiagnosing a "failed compressor."
Common Problems This Part Fixes
Compressor won't start — no power boost from the failed capacitor
Compressor hums or clicks but doesn't start running
Compressor kicks on and off repeatedly (short cycling)
Refrigerator and freezer too warm — cooling cycles not completing
Fridge too warm while freezer seems okay — weak compressor operation
Noticeable humming sounds from the back of the refrigerator
Inconsistent cooling and variable temperatures inside the refrigerator
Refrigerator will not start at all
Capacitor visibly bulged, leaking, or burned
Capacitance test reads significantly off from 12 µF
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This run capacitor directly replaces the following OEM and cross-reference part numbers:
WPW10350564, W10350564, PD00030179, EAP11753490, AP6020176, AWP50050, PS11753490.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This run capacitor is compatible with select refrigerators and freezers from the following brands:
Whirlpool refrigerators — French door, side-by-side, and bottom-mount models (including WRX735SDBM00 and related WRX/WRF series)
Maytag refrigerators (select models)
KitchenAid refrigerators (select models)
Jenn-Air refrigerators (select models)
Amana refrigerators (select models)
Magic Chef refrigerators (select models)
Roper refrigerators (select models)
Admiral refrigerators (select models)
Ikea refrigerators (select Whirlpool-built models)
Kenmore / Sears refrigerators (select Whirlpool-built models)
Also fits compatible upright and chest freezers on the Whirlpool platform
Note: The run capacitor works together with the compressor start relay/start device. When one fails, the other has typically been stressed by the same electrical events — many repair scenarios call for replacing both at the same time since both are accessible in the same location and the combined parts cost is still far below a service call. Always verify your model number before ordering.
Key Features
Compressor run capacitor — delivers the phase-shifted power boost that starts the compressor motor and supports smooth operation during cooling cycles
Rated 12 µF (MFD) capacitance with ±5% tolerance — precise match to OEM electrical specifications
180VAC, 50/60Hz rating for compatible refrigerator compressor circuits
Resolves "compressor won't start," "humming but not starting," "short cycling," and "too warm" symptoms when caused by capacitor failure
A cost-effective first repair — failed capacitors commonly mimic the symptoms of a far more expensive failed compressor
Replaces WPW10350564, AP6020176, PS11753490, EAP11753490, and 2683570
Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Roper, Admiral, Ikea, and Kenmore refrigerators and freezers
Often replaced together with the compressor start relay/start device as a paired repair
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY repair — installs in about 15 minutes with basic hand tools
Product Specifications
Part Number
W10350564
OEM Part Number
WPW10350564
Part Type
Refrigerator Compressor Run Capacitor
Condition
Aftermarket Replacement
Application
Refrigerators and Freezers (Whirlpool platform)
Capacitance
12 µF (MFD)
Tolerance
±5%
Voltage
180V AC
Frequency
50/60 Hz
Mounting Location
Near compressor, rear of refrigerator
Often Paired With
Compressor Start Relay / Start Device
Compatible Brands
Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Roper, Admiral, Ikea, Kenmore
Installation Notes
⚠️ Capacitor Safety Warning — Stored Electrical Charge Capacitors store an electrical charge even after the refrigerator is unplugged. Before handling the old capacitor, discharge it safely: with the refrigerator unplugged, touch the blade of an insulated-handle screwdriver across both capacitor terminals simultaneously to short them together (you may see or hear a small spark — that's the stored charge dissipating). Never touch the capacitor terminals with bare hands before discharging. If you're not comfortable with this step, have the repair done by a qualified appliance technician.
⚠️ Unplug Refrigerator Before Starting — Wear Work Gloves Unplug the refrigerator and pull it away from the wall to access the rear. Safely store any food that could spoil if the repair takes longer than expected. Wear work gloves to protect your hands. The run capacitor is located near the compressor at the bottom rear of the refrigerator, typically behind a lower rear access panel. Remove the screws holding the access panel and set it aside. Locate the capacitor — a small rectangular or oval component connected to the compressor's start relay/start device by wire terminals. Photograph the wire connections before disconnecting anything. Discharge the old capacitor before touching the terminals (see the safety warning above). Disconnect the wire terminals from the old capacitor — note which wire goes to which terminal. Release the capacitor from its mounting clip or bracket. Install the new W10350564 capacitor in the same position, secure the mounting clip, and reconnect the wires to the same terminals as photographed. While the panel is open, inspect the start relay/start device on the side of the compressor — if it rattles when shaken, shows burn marks, or has corroded terminals, replace it at the same time. Reinstall the rear access panel, push the refrigerator back into place, plug it in, and listen for the compressor to start smoothly within a few minutes. Allow several hours for the refrigerator to return to its set temperature. Tools needed: Phillips screwdriver, 1/4" nut driver, insulated-handle flathead screwdriver (for discharging), needle-nose pliers, work gloves.
Frequently Asked Questions
How do I know if the run capacitor has failed and not the compressor?
This is the key question — because a failed $15–30 capacitor produces nearly identical symptoms to a failed $300+ compressor. Signs pointing to the capacitor: the compressor hums or clicks but won't start; the compressor tries to start, runs briefly, then shuts off (short cycling); or the refrigerator gradually stopped cooling with humming from the rear. To test: unplug the refrigerator, discharge the capacitor, disconnect it, and measure it with a multimeter that has a capacitance setting — a healthy capacitor reads close to 12 µF (within ±5%). A reading far off, zero, or infinite confirms the capacitor has failed. Visual signs like bulging, leaking, or burn marks also confirm failure. Given the low cost, replacing the capacitor (and start relay) first is the standard diagnostic approach before condemning the compressor.
Should I replace the start relay at the same time?
Yes, it's strongly recommended. The run capacitor and the compressor start relay/start device work together in the compressor's starting circuit — the relay switches power to the start winding while the capacitor provides the phase-shifted boost. When one fails, the other has typically been stressed by the same electrical events (voltage spikes, overheating, repeated failed start attempts). Both components are inexpensive, mounted in the same location on or near the compressor, and accessible in the same repair session. A quick relay check: with the refrigerator unplugged, remove the relay and shake it — if it rattles, the internal components have failed and it needs replacement.
Why does the capacitor need to be discharged before handling?
Capacitors store electrical energy — that's their job. Even after the refrigerator is unplugged, the capacitor can hold a charge capable of delivering a painful (and potentially dangerous) shock when you touch both terminals. Before handling, always discharge the capacitor by shorting both terminals together with the blade of an insulated-handle screwdriver — touch the metal blade across both terminals at once and hold for a second or two. You may see a small spark as the charge dissipates; that's normal. After discharging, the capacitor is safe to handle. This takes five seconds and eliminates the shock risk entirely.
What's the difference between a run capacitor and a start capacitor?
Both assist the compressor motor but in different phases of operation. A start capacitor delivers a large, brief boost only during the initial moment of motor startup, then is switched out of the circuit. A run capacitor — like the W10350564 — stays in the circuit continuously while the motor runs, providing an ongoing phase shift that improves the motor's running efficiency and torque. Household refrigerators on the Whirlpool platform typically use a run capacitor working alongside the start relay/start device. Match the replacement to your original: the W10350564 is a 12 µF, 180VAC run capacitor, and the capacitance rating must match for correct compressor operation.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications (12 µF ±5%, 180VAC, 50/60Hz), terminal configuration, and compressor-support function of the original WPW10350564/W10350564 run capacitor used in compatible Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, and Kenmore refrigerators and freezers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO WR55X10025 Refrigerator Temperature Sensor
The XPARTCO WR55X10025 is an aftermarket replacement refrigerator temperature sensor (thermistor) compatible with a wide range of GE, Hotpoint, Haier, Café, and Monogram refrigerators. The temperature sensor monitors air temperature inside the fresh food and freezer compartments and sends that data to the main control board, which uses it to regulate cooling cycles and maintain the correct set temperature. When the sensor fails, the refrigerator may run too warm, too cold, or experience erratic defrost behavior.
This sensor measures approximately 1-1/4 inches long and includes 18-inch wire leads. It is constructed from white plastic and is used in both fresh food and freezer compartments depending on the model — on some models it also functions as a defrost sensor on the evaporator coil. It directly replaces OEM part numbers WR55X10025 and a large number of earlier GE thermistor part numbers. Sold individually — some models require two sensors. Installs in under 30 minutes with basic hand tools.
Quick Answer
The XPARTCO WR55X10025 Refrigerator Temperature Sensor fixes GE and Hotpoint refrigerators that are too warm, too cold, not defrosting, or over-defrosting. The thermistor monitors compartment temperature and communicates with the control board. Approx. 1-1/4" long with 18" leads, white plastic. Compatible with GE, Hotpoint, Haier, Café, and Monogram refrigerators. Sold individually.
Common Problems This Part Fixes
Refrigerator compartment running too warm — food spoiling faster than normal
Refrigerator running too cold — food or liquids freezing in the fresh food section
Freezer section not maintaining correct temperature
Refrigerator not defrosting or defrosting too frequently
Excessive frost or ice buildup on evaporator coils
Refrigerator and freezer both warming up after extended defrost cycles
Erratic cooling — temperatures fluctuating unpredictably
Replaces Part Numbers
This temperature sensor directly replaces the following OEM and cross-reference part numbers:
WR55X10025, 914093, WR50X10027, WR50X10034, WR50X10055, WR50X10067, WR55X10025-50PK, WR55X10025B, WR55X10026, WR55X10027, WR55X10028, WR55X10030, WR55X10087, WR55X10088, WR55X10089, WR55X10367, WR55X10380, WR55X10661, WR55X10711, WR55X10735, WR55X10736, WR55X10737, WR55X10937, WR55X10938, WR55X10939, WR55X11121, WR55X11141, WR55X11151, WR55X11152, AH304103, EA304103, OEM9556230, AP3185407, EAP304103, AGE29661, PD00000992, PS304103
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This temperature sensor is compatible with select refrigerators from the following brands:
GE refrigerators (side-by-side, French door, top-freezer, and bottom-freezer)
Hotpoint refrigerators
Haier refrigerators (select GE-platform models)
Café refrigerators
Monogram refrigerators
Note: Some GE refrigerator models use two or more temperature sensors. This part is sold individually. Check your model's parts diagram or contact our support team to confirm how many sensors your model requires before ordering.
Key Features
Monitors fresh food and freezer compartment temperatures and communicates readings to the main control board
Also functions as a defrost sensor on the evaporator coil on applicable models
Fits both fresh food and freezer positions
White plastic construction — durable and resistant to refrigerator temperature extremes
Direct replacement for WR55X10025 and over 30 earlier GE thermistor part numbers
Compatible with GE, Hotpoint, Haier, Café, and Monogram refrigerators
Sold individually — verify quantity needed for your model before ordering
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY repair — installs in under 30 minutes with basic hand tools
Product Specifications
Part Number
WR55X10025
Part Type
Refrigerator Temperature Sensor (Thermistor)
Condition
Aftermarket Replacement
Application
Fresh food compartment, freezer compartment, and evaporator coil (defrost sensor) depending on model
Sensor Body Length
Approximately 1-1/4 inches
Color
White
Material
Plastic
Includes
Sensor with wire leads
Sold As
Single sensor (some models require 2 — verify before ordering)
Compatible Brands
GE, Hotpoint, Haier, Café, Monogram
Installation Notes
⚠️ Unplug Refrigerator Before Starting Unplug the refrigerator from the power outlet before beginning any repair. To access the fresh food thermistor, locate the sensor on the left wall of the fresh food compartment — it may be clipped into a housing or bracket. Disconnect the wire connector and pull the old sensor out of its bracket. Slide the new WR55X10025 sensor into the bracket and reconnect the wire connector. To access the freezer or evaporator thermistor, remove the freezer shelves and back panel, then locate the sensor clipped to the evaporator coil bracket. Remove any tie wrap securing the sensor, pull the old sensor from the bracket, insert the new sensor, and reconnect the wire connector. Reinstall the back panel and shelves, restore power, and verify the refrigerator returns to the correct set temperature. Tools needed: Phillips screwdriver, flat pry tool (for panel clips), work gloves.
Frequently Asked Questions
How many temperature sensors does my GE refrigerator have?
The number of sensors varies by model. Many GE French door and side-by-side refrigerators use two or three WR55X10025 sensors — one in the fresh food compartment, one in the freezer, and sometimes one on the evaporator coil. Check your model's parts diagram or contact our support team with your model number to confirm how many you need before ordering.
What is a thermistor and how does it work?
A thermistor is a type of resistor whose electrical resistance changes with temperature. The main control board sends a small voltage through the thermistor and measures the resistance — a higher resistance means a lower temperature, and a lower resistance means a higher temperature. The board uses this reading to decide when to run the compressor and fans to maintain the set temperature. A failed thermistor sends incorrect readings, causing the refrigerator to over-cool, under-cool, or malfunction during defrost cycles.
Can a faulty temperature sensor cause the refrigerator to not defrost?
Yes. On models where the WR55X10025 also serves as the defrost sensor on the evaporator coil, a faulty sensor can cause the control board to incorrectly time or skip defrost cycles entirely — leading to excessive frost or ice buildup on the evaporator coils. This frost buildup can eventually block airflow and cause both the refrigerator and freezer sections to warm up.
How do I know if my temperature sensor is the cause of my cooling problem?
The most reliable way to test the thermistor is with a multimeter. Disconnect the sensor and measure its resistance at room temperature — a working WR55X10025 should read approximately 16,000 ohms at 32°F, dropping as temperature increases. An open circuit (infinite resistance) or short circuit (zero resistance) reading confirms the sensor has failed. If resistance is within the normal range but the refrigerator still has issues, the control board or other components may be at fault.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from durable plastic to match the dimensions and performance specifications of the original WR55X10025 temperature sensor.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
WR30X39470 Refrigerator Genuine Ice Maker
Fits specific GE refrigerator models.
Replaces Part Numbers: WR30X39470, AP7192967, OEM28771870, PS16729732.
Description: This Refrigerator Ice Maker Assembly is essential for restoring your refrigerator's ice production capabilities. This Genuine OEM part ensures seamless compatibility with a wide range of GE refrigerator models, providing reliable and consistent ice making. Crafted with high-quality materials, the Ice Maker Assembly delivers efficient performance, helping you maintain a steady supply of ice for your daily needs. Its sturdy design ensures long-lasting durability, reducing the need for frequent replacements. Installing this part is straightforward, allowing you to quickly get your refrigerator back to full functionality without hassle. Whether your original ice maker is malfunctioning, leaking, or has worn out over time, the Refrigerator Ice Maker Assembly offers a perfect replacement solution.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
Genuine OEM AEQ72910411 Refrigerator Ice Maker Assembly
The Genuine OEM LG AEQ72910411 is a complete ice maker assembly kit for LG refrigerators. The ice maker takes in water, freezes it into ice cubes, and releases them into the ice storage bin. 12-cube ice maker assembly. The kit includes the complete ice maker and housing, so it replaces the whole unit rather than a single component. If your refrigerator has stopped making ice and the water supply and freezer temperature check out, a faulty ice maker assembly may be the cause.
This is the original LG part, not an aftermarket equivalent. Because LG uses different ice makers across its refrigerator lines, check the part number against your model before ordering.
Quick Answer
The Genuine OEM AEQ72910411 Ice Maker Assembly replaces a failed ice maker in a compatible LG refrigerator that has stopped producing ice. Kit includes the complete ice maker and housing. Classic symptom: the refrigerator is cold and the water supply is on, but the ice bin stays empty.
Common Problems This Part Fixes
Refrigerator has stopped making ice
Ice maker not filling or freezing a new batch
Ice maker not releasing ice into the bin
Damaged or worn ice maker housing
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This ice maker assembly is listed under the following part number:
AEQ72910411, 2629334, ALG53099, AP5675948, EAP7788168, OEM17027853, PD00029871, PS7788168
We have not found any superseded or alternate manufacturer numbers for this assembly. If your old ice maker or parts diagram shows a different number, contact our support team and we'll check whether it matches.
Compatibility
This ice maker assembly is listed for LG refrigerators, including these examples:
LG LFX25974SB, LFX25974ST, LFX25974SW
LG LFX28968SB, LFX28968ST, LFX28968SW
Revision suffixes such as LFX25974ST/01 and LFX28968ST/00
Note: Retailers list these two model families, each with several revision suffixes. This is not a full list of every LG refrigerator that uses this ice maker. Check your full model number, including the suffix, against your parts diagram, or contact our support team to verify fit before ordering.
Key Features
Genuine OEM LG ice maker assembly, not an aftermarket equivalent
Kit includes the complete ice maker and housing
12-cube ice maker assembly
Replaces a faulty ice maker when the refrigerator has stopped producing ice
Listed for LG LFX25974 and LFX28968 series refrigerators
Product Specifications
Part Number
AEQ72910411
OEM Part Number
AEQ72910411
Part Type
Refrigerator Ice Maker Assembly Kit, 12-cube ice maker assembly
Condition
Genuine OEM
Manufacturer
LG
Kit Includes
Complete Ice Maker and Housing
Application
LG Refrigerators
Installation Notes
⚠️ Unplug Power And Shut Off Water Before Installing Unplug the refrigerator and turn off its water supply before beginning, and wear work gloves. Empty the ice bin and follow your model's service guide to reach and remove the ice maker. Note how the wiring is connected before disconnecting it, remove the old ice maker, and fit the new one in the same position. Reconnect the wiring, restore water and power, and allow time for the new ice maker to produce and release its first batches of ice.
Frequently Asked Questions
My refrigerator stopped making ice. Is this the part I need?
A failed ice maker is one possible cause. Before replacing it, check that the water supply is on and the water line isn't frozen, and that the freezer is cold enough. If those are fine and the ice maker still doesn't make or release ice, replacing the assembly is the next step.
What is included in the kit?
Retailers describe it as the complete ice maker and housing. They do not itemize individual components, so contact our support team if you need to confirm exactly what is in the box.
Is this an OEM or aftermarket part?
This is a genuine OEM part from LG, not an aftermarket equivalent.
Will this fit my refrigerator?
It is listed for LG LFX25974 and LFX28968 series refrigerators. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
Genuine OEM DA82-02675A Refrigerator Ice Maker Service Kit
The Genuine OEM Samsung DA82-02675A is an ice maker service kit for select Samsung French door refrigerators. The ice maker controls water flow, freezes the water into cubes and dispenses the ice. When the ice maker stops producing ice or ice jams and blockages build up, this kit replaces the worn or missing ice maker components.
This is the original Samsung part, not an aftermarket equivalent. It is sold as a kit. Check your model number before ordering.
Quick Answer
The Genuine OEM DA82-02675A Ice Maker Service Kit replaces the ice maker components on a compatible Samsung refrigerator when it has failed. Classic symptoms: no ice production, or ice blockages caused by worn or missing components.
Common Problems This Part Fixes
Ice maker not producing ice
Ice blockages or poor ice flow caused by worn or missing ice maker components
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This ice maker service kit is listed under the following part number:
DA82-02675A, AP6883222, ASM31463 , EAP12719619, PD00055329, PS12719619
If your old ice maker shows a different number, contact our support team and we'll check whether it matches.
Compatibility
This ice maker service kit is listed for Samsung French door refrigerators, including these examples:
Samsung RF28JBEDBSG/AA (00 through 06 versions)
Samsung RF28JBEDBSR/AA (00 through 06 versions)
Note: The models above are a sample from one retailer, not a full list. Samsung uses several ice maker assemblies with different part numbers. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering.
Key Features
Genuine OEM Samsung part, not an aftermarket equivalent
Multi-part ice maker service kit
Controls water flow, freezes the water into cubes and dispenses ice
Sold as a kit
Product Specifications
Part Number
DA82-02675A
OEM Part Number
DA82-02675A
Part Type
Refrigerator Ice Maker Service Kit
Condition
Genuine OEM
Manufacturer
Samsung
Quantity
1 Kit
Application
Select Samsung French Door Refrigerators
Installation Notes
⚠️ Disconnect Power And Water Before Installing Unplug the refrigerator and shut off the water supply before you begin. Remove the ice bucket and any shelves that block the ice maker, then detach the old ice maker components as needed. Install the kit components following the instructions in the kit, reinstall the bucket and shelves, and make sure everything is secure. Restore power and water and test ice production and flow.
Frequently Asked Questions
My refrigerator isn't making ice. Is this the part I need?
It can be. Check the water supply and fill line first, since a water problem can cause the same symptom. If those are fine and the ice maker is worn or damaged, this kit replaces its components.
Is this an OEM or aftermarket part?
This is a genuine OEM part from Samsung, not an aftermarket equivalent.
What is in the kit?
It is sold as an ice maker service kit made up of several parts. Retailers describe the contents differently, so contact our support team if you need to confirm them before ordering.
Will this fit my refrigerator?
It is listed for select Samsung French door models, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
240597220 Genuine OEM Frigidaire Refrigerator Temperature Sensor
The 240597220 is a Genuine OEM Frigidaire replacement refrigerator temperature sensor compatible with a wide range of Frigidaire, Electrolux, Kenmore (253/106/795 prefix), Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, and Ikea refrigerators and household freezers. This NTC (negative temperature coefficient) thermistor continuously monitors the temperature inside the refrigerator or freezer compartment and sends resistance-based readings to the main control board, which uses this data to cycle the compressor, fans, and defrost heaters to maintain accurate temperatures. As the thermistor heats up or cools down, its electrical resistance changes predictably, allowing the control board to calculate the exact temperature in real time.
When this sensor fails or drifts out of range, the refrigerator may run too cold or too warm, cycle excessively, freeze up the evaporator, fail to maintain set temperatures, or display OP error codes. Rated 10K Ohm NTC, with a 5/16" diameter probe, 12" wire, and overall dimensions of 3-5/8"L x 5/8"W x 5/16"H (sensor probe itself measures ~1-3/16"L x 5/16" diameter). Compatible with 20-28 cubic foot North American household refrigerators in French door, side-by-side, top-freezer, and bottom-freezer configurations (post-2005 production). 240597220 is the current OEM part number, superseding 240597203, 240597201, and 240597202. It also replaces 7240597203, AP4032998, AP7243155, AH1765215, EA1765215, EAP1765215, EAP17647917, 1258948, 4985585, OEM21729470, PD00000590, PD00088922, PS1765215, and PS17647917. Not compatible with mini fridges, car refrigerators, commercial units, wine coolers, or ice makers. Installs in 15–20 minutes with basic hand tools.
Quick Answer
The 240597220 Genuine OEM Frigidaire Refrigerator Temperature Sensor fixes Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, and Ikea refrigerators that run too cold or warm, cycle excessively, freeze up the evaporator, or display OP error codes. NTC thermistor — 10K Ohm at room temperature. 5/16" probe diameter, 12" wire. Overall 3-5/8"L x 5/8"W x 5/16"H. Genuine OEM. Supersedes 240597203, 240597201, 240597202. Also replaces 7240597203, AP4032998, AP7243155, AH1765215, EA1765215, EAP1765215, EAP17647917, 1258948, 4985585, OEM21729470, PD00000590, PD00088922, PS1765215, PS17647917. For 20–28 cu ft household refrigerators built 2005 or later.
Common Problems This Part Fixes
Refrigerator running too cold or too warm — sensor not accurately reporting temperature
Inconsistent temperatures — fluctuating cooling that can't maintain set point
OP error code displayed on the control panel (open sensor circuit)
Excessive frost or ice buildup on evaporator coils from erratic defrost timing
Refrigerator running continuously without cycling off
Freezer over-freezing food or fresh food compartment freezing groceries
Food spoilage from temperature instability
Multimeter test shows 0 ohms (shorted), infinite resistance (open), or drifted resistance instead of the expected ~10K Ohms at room temperature
Replaces Part Numbers
This temperature sensor is the current OEM part number and supersedes the following OEM and cross-reference part numbers:
240597220, 240597203, 240597201, 240597202, 7240597203, 4985585, AFR15666, AP7243155, EAP17647917, OEM21729474, PD00088922, PS17647917.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This temperature sensor is compatible with select household refrigerators and freezers from the following brands (20–28 cu ft, built 2005 or later):
Frigidaire refrigerators — Gallery and Professional series, plus standard Frigidaire models (BFHS2611LM, BGHS2634KE, BGHS2634KP, BGHS2644KF, CRSH237LB, PRFG2383AF, PRFC2383AF, ERFG2393AS2, FRSS2323AS8, FFHB2740PP5A and many related models)
Frigidaire upright freezers — FFFH21F7QW, FGU19F6QWB and related models
Electrolux refrigerators — EI24RD65KS0, EI24RD65HS0, EI24RD65HS1, E24RD75KPS0 and related models
Kenmore / Sears refrigerators — 253-prefix, 106-prefix, and 795-prefix models (select Frigidaire/Electrolux-built units)
Crosley refrigerators (select Frigidaire-built models)
White-Westinghouse refrigerators (select models)
Kelvinator refrigerators (select models)
Gibson refrigerators (select models)
Tappan refrigerators (select models)
Viking refrigerators (select Frigidaire-platform models)
Ikea refrigerators (select Frigidaire-platform models)
Not compatible with: mini fridges, car refrigerators, commercial refrigerators/freezers, wine coolers, or dedicated ice makers. Verify your refrigerator was produced after 2005 and check the original part number on the fridge nameplate matches one of the cross-references listed. Contact our support team with your model number if you're unsure.
Key Features
NTC (negative temperature coefficient) thermistor — resistance changes predictably with temperature, allowing precise temperature monitoring
Rated 10K Ohms at room temperature (approximately 25°C / 77°F)
Sends real-time temperature data to the main control board to regulate compressor cycling, fan operation, and defrost timing
Sensor probe: 5/16" diameter x 1-3/16" length · Overall assembly: 3-5/8"L x 5/8"W x 5/16"H · 12" wire lead
White plastic/metal construction with glossy finish
Resolves OP error codes when caused by an open sensor circuit
Compatible with 20–28 cu ft French door, side-by-side, top-freezer, and bottom-freezer refrigerators built 2005 or later
Current OEM part number — supersedes 240597203, 240597201, 240597202 and replaces AP4032998, AH1765215, PS1765215, PS17647917 and additional cross-references
Compatible with Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, Ikea
Genuine OEM part manufactured by Frigidaire/Electrolux to factory specifications — guaranteed fit and performance
Quick DIY repair — installs in 15–20 minutes with basic hand tools
Product Specifications
Part Number
240597220
Supersedes
240597203, 240597201, 240597202
Part Type
Refrigerator Temperature Sensor (NTC Thermistor)
Condition
Genuine OEM
Application
Household Refrigerators and Freezers (Frigidaire/Electrolux platform, 20–28 cu ft, 2005+)
Sensor Type
NTC (Negative Temperature Coefficient)
Resistance
10K Ohms at room temperature
Probe Dimensions
5/16" Diameter x 1-3/16" Length
Overall Dimensions
3-5/8"L x 5/8"W x 5/16"H
Wire Length
12"
Color
White
Finish
Glossy
Material
Plastic / Metal
Error Codes Resolved
OP (open sensor circuit)
Compatible Brands
Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, Ikea
Installation Notes
⚠️ Unplug Refrigerator and Move Perishable Food Before Starting — Wear Work Gloves Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves to protect your hands. Depending on your refrigerator model, the fresh-food temperature sensor is typically located behind the air tower or damper assembly on the rear interior wall of the refrigerator compartment; the freezer temperature sensor is typically located behind the rear freezer access panel near the evaporator coils. Confirm which sensor location matches your symptom and the parts diagram for your specific model before starting. Remove all shelves, drawers, and any items blocking access to the sensor location. Remove the screws holding the air tower/damper cover (fresh food side) or rear freezer access panel to expose the sensor. Photograph the sensor position, wire routing, and connector before removing. Disconnect the wire connector (gently — the connector can be fragile) and release the sensor from its mounting clip. Fully insert the new 240597220 sensor probe into the card slot (no exposure) and secure with the mounting clip. Reconnect the wire connector — plug wiring terminals tightly to avoid poor contact. Use cable ties to secure any loose wire routing as before. Reinstall the cover or panel, replace the shelves and drawers, and plug the refrigerator back in. Allow several hours for the refrigerator to return to its set temperature before reloading with food. Tools needed: Phillips screwdriver, cable ties, multimeter (for testing), work gloves.
Frequently Asked Questions
What does OP error code mean on my Frigidaire refrigerator?
The OP error code (Open) indicates the control board is detecting an open circuit on a temperature sensor input — meaning the sensor is failing to send a resistance signal, either because the sensor itself has failed open internally, the wire has broken, or the connector isn't seated. Replacing the temperature sensor typically resolves the code when the sensor itself is the cause. If the code persists after replacement, check the wire harness between the sensor and the control board for damage, and confirm the connector is fully seated. If the OP code appears alongside other symptoms like frost buildup and cooling issues that persist after sensor replacement, the defrost temperature sensor (on the Harness-Low Side, a different part number) may also need to be replaced, or the main control board may be at fault.
How do I test if the temperature sensor has failed?
Unplug the refrigerator, disconnect the sensor's wire connector, and set your multimeter to resistance mode. At room temperature (approximately 25°C / 77°F), a working NTC thermistor should read approximately 10K Ohms. If the sensor reads 0 ohms, it has shorted internally. If it reads infinite resistance (open circuit, often shown as "OL" on the multimeter), the sensor has failed open. If it reads significantly off from 10K (for example 8.4K or 5K at room temp), the sensor has drifted and is no longer providing accurate readings — replacement is recommended. Any of these results confirms the sensor needs replacement.
My refrigerator has multiple temperature sensors — which one do I replace?
Frigidaire refrigerators typically use multiple temperature sensors: one in the fresh food compartment (behind the air tower/damper), one in the freezer compartment (near the evaporator coils), and often a separate defrost temperature sensor on the Harness-Low Side. The 240597203 is used as the fresh food or freezer compartment temperature sensor. If your symptom is "fresh food too warm" or "freezer over-freezing," the fresh food sensor is the likely candidate. If your symptom is "freezer icing up despite defrost heater working," the defrost temperature sensor may be the culprit — a different part number. Check your refrigerator's parts diagram to confirm the correct sensor location for your specific symptom.
Does this sensor fit my Kenmore refrigerator?
On many Kenmore refrigerators, yes — Sears sells Kenmore-branded refrigerators that are manufactured by Frigidaire/Electrolux, Whirlpool, LG, and Samsung. The 240597203 sensor fits Kenmore refrigerators with model numbers beginning with the 253, 106, or 795 prefixes that are Frigidaire/Electrolux-built. Kenmore refrigerators built by other manufacturers (Whirlpool, LG, Samsung) use different sensors. Check the first three digits of your Kenmore model number — if it's 253, 106, or 795 and falls within the compatible model list, this is the correct part.
Is this an OEM or aftermarket part?
This is a Genuine OEM part manufactured by Frigidaire/Electrolux to factory specifications. It is the exact same temperature sensor installed in compatible Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse, Kelvinator, Gibson, Tappan, Viking, and Ikea refrigerators from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 2315539 Refrigerator Evaporator Fan Motor Replaces WP2315539
The XPARTCO 2315539 is an aftermarket replacement refrigerator/freezer evaporator fan motor compatible with a wide range of Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Admiral, Estate, Inglis, Ikea, and Gladiator refrigerators. The evaporator fan motor is located in the freezer section and circulates air across the evaporator coils — the cold air generated at the coils is then pushed throughout the freezer and the fresh food compartment. When this motor fails, the most common symptom is excessive noise from the freezer area, and often the refrigerator section won't cool properly even though the freezer remains cold.
This motor includes the incorporated wire harness and plug. Rated 115V, 60Hz, with clockwise rotation. It directly replaces WP2315539, WP2315539VP, 2219689, 2225625, W10438708, 1372146, 1518337, AP3996841, AP6007247, ESF-U2B, EAP11740359, PD00021608, PS11740359, and PS1518337. Important: don't forget to transfer the two rubber grommets from your old motor to the new one for proper mounting. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The XPARTCO 2315539 Refrigerator Evaporator Fan Motor fixes Whirlpool, Kenmore, Maytag, KitchenAid, and Amana refrigerators with excessive noise from the freezer area, ice buildup in the freezer, or where the fresh food section is warm but the freezer is still cold. Includes incorporated wire harness and plug. 115V, 60Hz, clockwise rotation. Transfer rubber grommets from old motor for mounting. Replaces WP2315539, WP2315539VP, 2219689, 2225625, W10438708, 1372146, AP3996841, AP6007247, ESF-U2B, EAP11740359, PS11740359, PS1518337.
Common Problems This Part Fixes
Excessive noise from the freezer area — most common symptom of evaporator fan motor failure
Loud humming, whining, grinding, or scraping noises during operation
Freezer compartment cold but fresh food section warm — cool air not being circulated
Heavy ice buildup on the evaporator coils or rear freezer wall
Refrigerator running continuously trying to maintain temperature
Fan blade not spinning freely or seized when checked by hand
Motor failing continuity test with a multimeter
Visible damage to the fan motor housing or harness
Replaces Part Numbers
This evaporator fan motor directly replaces the following OEM and cross-reference part numbers:
WP2315539, 2315539, W10438708, 1372146, 2219689, 2225625, ESF-U2B, AP6007247, AWP47336, EAP11740359, PD00003243, PS11740359.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This evaporator fan motor is compatible with select refrigerators from the following brands:
Whirlpool refrigerators (top-mount, side-by-side, and Gold series — select models)
Kenmore / Sears refrigerators (Whirlpool-built — select 106-series and related models)
Maytag refrigerators (select models)
KitchenAid refrigerators (select models)
Amana refrigerators (select models)
Roper refrigerators (select models)
Crosley refrigerators (select models)
Admiral refrigerators (select models)
Estate refrigerators (select models)
Inglis refrigerators (select models)
Ikea refrigerators (select Whirlpool-built models)
Gladiator refrigerators (select models)
Note: This motor includes an incorporated wire harness. If your old motor has a separate wire harness (not incorporated), confirm the correct part with our support team before ordering. Always verify your model number first. Remember to transfer the two rubber grommets from your old motor to the new one — they're essential for proper mounting.
Key Features
Refrigerator/freezer evaporator fan motor — circulates cold air from the evaporator coils throughout both the freezer and fresh food compartments
Includes incorporated wire harness and plug — direct plug-in installation
Rated 115V, 60Hz — correct electrical specifications for compatible Whirlpool-platform refrigerators
Clockwise motor rotation
Replaces WP2315539, WP2315539VP, 2219689, 2225625, W10438708, 1372146, AP3996841, AP6007247, ESF-U2B, PS11740359, PS1518337, and additional cross-references
Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Admiral, Estate, Inglis, Ikea, and Gladiator refrigerators
Important: transfer the two rubber grommets from the old motor to the new one for proper mounting
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
2315539
OEM Part Number
WP2315539
Part Type
Refrigerator Evaporator Fan Motor (Freezer Section)
Condition
Aftermarket Replacement
Application
Refrigerators (Whirlpool platform)
Voltage
115V AC
Frequency
60 Hz
Rotation
Clockwise
Wire Harness
Incorporated wire harness and plug included
Mounting
Transfer two rubber grommets from old motor
Compatible Brands
Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Admiral, Estate, Inglis, Ikea, Gladiator
Installation Notes
⚠️ Unplug Refrigerator and Move Perishable Food Before Starting — Wear Work Gloves Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves to protect your hands. The evaporator fan motor is located behind the rear access panel inside the freezer compartment. Remove the freezer shelves and any internal components blocking access to the rear panel. Remove the screws holding the rear access panel to expose the evaporator coils and fan motor (a 1/4" hex driver is commonly needed). Photograph the wire connections and fan blade orientation before disconnecting. Disconnect the wire harness connector from the old motor. Note the orientation of the fan blade on the motor shaft and the position of the two rubber mounting grommets — both must be transferred to the new motor. Remove the mounting screws or release the motor from its bracket, and pull the old motor free. Transfer the rubber grommets and fan blade (if not pre-installed) to the new 2315539 motor in the same orientation. Install the new motor in the same position, reconnect the wire harness, and reinstall the access panel and shelves. Plug the refrigerator back in and allow several hours for the unit to return to its set temperature before reloading with food. Tools needed: 1/4" hex driver, Phillips screwdriver, flathead screwdriver, work gloves.
Frequently Asked Questions
My freezer is making loud noise — is it the evaporator fan motor?
Yes, this is the most recognizable symptom of a failed evaporator fan motor on Whirlpool-platform refrigerators. When the motor's bearings wear out, it produces loud humming, whining, grinding, or scraping noises during operation. The noise often varies as the fan speed changes or as ice builds up around the fan blade. To confirm, unplug the refrigerator and access the fan behind the rear freezer panel — try turning the blade by hand. If it doesn't spin freely, is stiff, or seizes, the motor bearing has failed and needs replacement.
My freezer is cold but my fridge is warm — could this be the cause?
Yes — on many Whirlpool-platform refrigerators, the freezer's evaporator fan motor is responsible for circulating cool air from the freezer evaporator into the fresh food compartment as well. When this fan fails, the freezer's own compartment may stay cold because the cold air is generated right there, but the fresh food section warms up because no air is being moved into it. If your fridge is warm while the freezer remains cold, this is a likely cause — especially if you also hear unusual noise from the freezer area or see ice buildup on the evaporator coils.
What is the difference between 2315539 and WP2315539?
These are the same evaporator fan motor. WP2315539 is the updated Whirlpool OEM part number that superseded the original 2315539. The 2219689, 2225625, W10438708, and ESF-U2B are also cross-references for this same motor across various Whirlpool catalog revisions and production runs. This aftermarket replacement is compatible with all of these numbers.
Why do I need to transfer the rubber grommets from the old motor?
The two rubber grommets seat between the motor housing and the mounting bracket inside the refrigerator. They isolate the motor from the cabinet to dampen vibration and reduce noise during operation, and they also keep the motor properly positioned in its mount. The new 2315539 typically ships without these grommets — they are reused from the old motor. Remove them carefully from the old motor before discarding it, and slide them onto the new motor in the same positions. Without the grommets, the motor may run noisily or vibrate excessively.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, electrical specifications (115V AC, 60Hz, clockwise rotation), incorporated wire harness, and function of the original WP2315539/2315539 evaporator fan motor.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
Genuine GE OEM Part
GE WR55X36435 Refrigerator Genuine OEM Inverter Board
Compressor inverter/control board for select GE refrigerator platforms.
Product Overview
The GE WR55X36435 Refrigerator Inverter Board is a Genuine GE OEM replacement part designed for compatible GE refrigerators.
The inverter board supplies and controls electrical power to the variable-speed compressor, allowing the refrigerator control system to regulate compressor operation for proper cooling performance.
Quick Answer
WR55X36435 is a Genuine GE OEM refrigerator compressor inverter board. It replaces WR55X31991 and WR87X32289 on compatible models. Always verify the full refrigerator model number before ordering because inverter boards are model-specific electronic controls.
Common Problems This Part May Fix
Compressor does not start
Refrigerator is not cooling properly
Compressor starts and stops unexpectedly
Intermittent cooling caused by inverter failure
Diagnostic fault related to compressor drive/control
Replaces and Cross-References
WR55X36435, WR87X32289, WR55X31991, AP6980849, AP7176581, EAP16660026, AGE29171, OEM21529752, PD00078524, PS16660026
Cross-reference numbers are for identification. Verify your exact appliance model before purchase.
Compatibility
Designed for select GE bottom-mount and French-door refrigerator platforms. Compatible model examples include:
CVE28DP3NBD1
CVE28DP4NBW2
CVE28DM5NBS5
PVD28BYNCFS
PVD28BYNFS
PGD29BYTBFS
PGD29BYTCFS
CGE29DP2TBS1
CXE22DP2PBS1
Important: This is only a partial compatibility list. Inverter boards can look similar while using different firmware, connectors, or compressor specifications. Confirm the complete model number before ordering.
Key Features
Genuine GE OEM replacement part
Controls/supplies power to the compressor
Replaces WR55X31991 and WR87X32289
Factory-designed electrical connectors and mounting
For select GE refrigerator platforms
Product Specifications
Manufacturer Part Number
WR55X36435
Brand
GE Appliances
Part Type
Refrigerator Compressor Inverter Board
Condition
New
Part Quality
Genuine OEM
Primary Function
Supplies and controls power to the compressor
Approx. Shipping Weight
0.65 lb
Package Quantity
1 Inverter Board
Installation Notes
Unplug the refrigerator before service.
Protect perishable food while power is disconnected.
Verify the exact appliance model and original inverter part number.
Document wiring and connector locations before removal.
Inspect the compressor harness, connectors, and related wiring for heat damage or corrosion.
Install the replacement in the original mounting location and reconnect all plugs fully.
Reassemble all covers before restoring power.
Electronic diagnostic note: A no-start compressor can also be caused by the compressor itself, main control board, wiring, sensors, or supply-voltage problems. Diagnose the system before replacing the inverter board.
Frequently Asked Questions
Is WR55X36435 a Genuine GE OEM part?
Yes. WR55X36435 is a Genuine GE Appliances inverter board.
Does it replace WR55X31991?
Yes. WR55X31991 is a previous part number replaced by WR55X36435 on compatible models.
Does it replace WR87X32289?
Yes. WR87X32289 is also a previous part number replaced by WR55X36435 on compatible models.
What does the inverter board do?
It supplies and controls electrical power to the refrigerator compressor so the cooling system can operate at the commanded speed and load.
Will this fit every GE refrigerator?
No. Verify the complete model number because compressor inverter boards are model-specific.
Shop With Confidence
Use the complete refrigerator model number to confirm fitment before purchase. Genuine OEM electronics are designed for the specific electrical and compressor requirements of compatible GE models.
Genuine GE OEMCompressor InverterCompatibility SupportFast U.S. Shipping
XP4P-ROLP-120P15 Refrigerator Starter Relay & Overload Protector
Refrigerator Compressor Overload Protector PTC Starter Relay Replaces 1.03.01.01.324J, ZHB35-120P15 BEU: This PTC starter relay is specifically designed for refrigerator compressors. It serves as an overload protector and ensures the proper functioning of your refrigerator compressor. The model ZHB35-120P15 BEU guarantees compatibility with your appliance.
Description: Easy to install and replace your old part: This PTC starter relay for refrigerator compressor overload protector is designed for easy installation and replacement of your old part. It saves you time and effort in the installation process. Check well before shipment: Each unit of this refrigerator compressor overload protector PTC starter relay is carefully checked before shipment to for ensure its quality and functionality.
This is an aftermarket part that can be used as a replacement for the OEM part.
WR30X39385 Genuine OEM GE Refrigerator Ice Maker
The WR30X39385 is a genuine GE OEM ice maker assembly for GE refrigerators. This complete unit receives water, holds it in an internal mold, and freezes it into cubes, then ejects the finished ice into the freezer's ice bucket or drawer, repeating the cycle automatically until the bucket is full. It's the full assembly, not just an internal component, so replacing it addresses the ice-making mechanism, mold, and cycling controls together as one unit.
Over time, internal components can wear or fail electrically, or the mold itself can develop issues that affect how cleanly ice releases. A failing ice maker typically shows up as reduced or stopped ice production, or ice cubes coming out hollow or malformed rather than solid. It directly replaces AP7179920.
Quick Answer
The WR30X39385 Genuine OEM GE Refrigerator Ice Maker fixes GE refrigerators that have stopped making ice, are producing significantly less ice than usual, or are making hollow or malformed cubes. Complete ice maker assembly. Replaces AP7179920. Installation is a moderate DIY repair, typically 30-45 minutes.
Common Problems This Part Fixes
Ice maker has stopped producing ice entirely
Ice maker producing significantly less ice than usual
Ice cubes coming out hollow or malformed instead of solid
Ice maker cycling but not ejecting cubes into the bucket
Inconsistent ice production from cycle to cycle
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This refrigerator ice maker directly replaces the following OEM and cross-reference part numbers:
WR30X39385, 200D1181G118, 4983508, Model CAN07-018, WR01F04991, AP7179920, EAP16660009, AGE28641, PD00079707, PS16660009
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This ice maker is compatible with select GE refrigerators, and also fits select Hotpoint, Haier, Monogram, and Café refrigerators built on the GE platform.
Note: Always verify your full model number before ordering, since GE uses several different ice maker designs across its refrigerator lineup. Contact our support team with your model number if you're unsure.
Key Features
Genuine GE OEM part — factory-specified mold design and cycling mechanism
Complete ice maker assembly — freezes water into cubes and ejects them automatically
Resolves "not making ice," "reduced ice production," and "hollow or malformed cubes" symptoms
Direct drop-in replacement — no modification required
Replaces AP7179920
Compatible with GE, Hotpoint, Haier, Monogram, and Café refrigerators
Genuine OEM replacement — guaranteed fit, materials, and performance
Moderate DIY repair, typically 30-45 minutes
Product Specifications
Part Number
WR30X39385
Part Type
Refrigerator Ice Maker Assembly
Condition
Genuine OEM
Brand
GE
Function
Freezes water into cubes and ejects them automatically into the ice bucket/drawer
Repair Difficulty
Moderate — 30 to 45 minutes
Quantity
1 ice maker assembly
Compatible Brands
GE, Hotpoint, Haier, Monogram, Café
Installation Notes
⚠️ Unplug Refrigerator Before Starting — Allow Components To Defrost Disconnect power to the refrigerator before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. If there's frost or ice buildup around the ice maker or its fill tube, allow the area to defrost fully before continuing, since ice buildup can make removal difficult and may mask the fill tube's actual condition. Open the freezer door and locate the ice maker assembly. Remove the ice bucket or drawer to improve access. Photograph the wiring harness connection and the fill tube position before disconnecting anything. Remove the mounting screws securing the ice maker in place, then disconnect the wire harness connector and the water fill tube connection. Remove the old ice maker fully. Install the new WR30X39385 in the same mounting position, making sure the fill tube aligns correctly so water reaches the mold without leaking, and reconnect the wire harness connector securely. Secure the mounting screws, reinstall the ice bucket or drawer, and restore power. Allow several hours for the first cycle to complete and confirm ice is being produced and ejected normally. Tools needed: Phillips screwdriver, work gloves.
Frequently Asked Questions
My ice cubes are coming out hollow. Is that the ice maker?
Yes, hollow or malformed cubes are a documented symptom of ice maker issues on this platform, alongside reduced or stopped ice production altogether. This can point to a problem with how the mold fills or releases ice, and replacing the complete assembly addresses the mold and cycling mechanism together rather than trying to diagnose and repair individual internal components.
Why does the fill tube alignment matter so much during installation?
The fill tube is what delivers water from the refrigerator's supply line into the ice maker's mold at the start of each cycle. If it's not aligned correctly during installation, water can miss the mold, leak into the freezer compartment, or fail to fill the mold completely, all of which prevent normal ice production even with a perfectly good new ice maker installed.
Do I need to defrost anything before starting this repair?
If there's visible frost or ice buildup around the old ice maker or its fill tube, yes — letting that area defrost fully makes removal easier and gives you a clearer look at the fill tube's actual condition, rather than working around ice that could mask damage or make the old unit harder to detach cleanly.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It includes the same mold design, cycling mechanism, and mounting configuration as the ice maker originally installed in your refrigerator.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
Genuine GE OEM Refrigerator Part
GE WR14X29372 Refrigerator Genuine Fresh Food Door Gasket - White
Genuine OEM fresh-food compartment door gasket for select GE and Hotpoint top-mount refrigerators.
Product Overview
The GE WR14X29372 Refrigerator Fresh Food Door Gasket is a Genuine GE OEM replacement seal for compatible refrigerator fresh-food doors. The gasket creates an airtight seal around the door perimeter to help keep warm room air out and cooled air inside.
This gasket is white and is designed for select GE and Hotpoint top-mount refrigerators.
Quick Answer
WR14X29372 is a Genuine GE OEM white fresh-food refrigerator door gasket. Replace it when the original gasket is torn, cracked, deformed, or no longer sealing properly. Always verify the complete appliance model number before ordering.
Common Problems This Part May Fix
Warm air entering the fresh-food compartment
Condensation or moisture around the refrigerator door
Excess frost or temperature instability
Door gasket is torn, split, cracked, or hardened
Door gasket has pulled away from the liner
Refrigerator runs longer because of air leakage
Replaces and Cross-References
WR14X29372, 4589966, AP6328755, EAP12298193, AGE28136, OEM18986274, PD00056633, PS12298193
Cross-reference numbers are provided for identification. Confirm fit using the complete refrigerator model number.
Compatibility
Fits select GE and Hotpoint top-mount refrigerators. Compatible model examples include:
GTE15CTHLRWW
GTE15CTHLLWW
GTE15CTHMRWW
GTE15NTHMRWW
GTS15CTHLRWW
GTS15CTHMRWW
FBS15RCKLRWW
HPS15BTHMRWW
HPE15BTHLRWW
Important: This is only a partial model list. Verify the complete refrigerator model number before purchase. Similar GE refrigerators may use a different fresh-food or freezer gasket.
Key Features
Genuine GE OEM replacement part
Fresh-food compartment door gasket
White color
Helps maintain an airtight door seal
Helps reduce warm-air infiltration and moisture
Designed for select GE and Hotpoint refrigerators
Product Specifications
Manufacturer Part Number
WR14X29372
Brand
GE Appliances
Part Type
Fresh Food Door Gasket
Color
White
Condition
New
Part Quality
Genuine OEM
Application
Refrigerator Fresh-Food Door
Approx. Shipping Weight
3.28 lb
Package Quantity
1 Door Gasket
Installation Notes
Safely store temperature-sensitive food before leaving the refrigerator door open for service.
Compare the new gasket with the original before removing the old seal.
If the replacement gasket arrives folded or creased, allow it to relax at room temperature or gently warm it according to manufacturer guidance before installation.
Remove the old gasket carefully and clean the mounting surface.
Install the new gasket evenly around the door perimeter without stretching it.
Close the door and inspect the entire seal for gaps, twists, or rolled edges.
Fit tip: GE service guidance notes that shipping folds/creases can be smoothed by warming the gasket gently. Do not overheat or deform the gasket.
Frequently Asked Questions
Is WR14X29372 a Genuine GE OEM gasket?
Yes. WR14X29372 is a Genuine GE Appliances refrigerator door gasket.
Is this the fresh-food or freezer gasket?
This part is for the fresh-food refrigerator door. The freezer door on many compatible models uses a different gasket.
What color is this gasket?
White.
Why does the new gasket look folded when it arrives?
Door gaskets are often folded for shipping. Gentle warming and allowing the gasket to relax can help remove temporary creases before installation.
Will this fit every GE refrigerator?
No. Verify the complete model number because GE uses different gaskets across refrigerator platforms.
Shop With Confidence
Verify the complete refrigerator model number before ordering. This is a Genuine GE OEM part made for compatible GE and Hotpoint refrigerators.
Genuine GE OEMFresh Food Door GasketWhiteCompatibility Support
Genuine GE OEM Refrigerator Part
GE WR14X29279 Freezer Genuine OEM Door Gasket
White magnetic freezer-door gasket for select GE, Haier, and Hotpoint top-mount refrigerators.
Product Overview
WR14X29279 is a Genuine GE OEM freezer door gasket. The gasket seals around the freezer door to help keep warm, humid room air from entering the freezer compartment.
A torn, hardened, twisted, or poorly sealing gasket can contribute to frost buildup, temperature instability, longer compressor run times, and moisture around the freezer opening.
Quick Answer
This listing is for one white Genuine GE OEM freezer door gasket, part WR14X29279. It is used on select compact GE, Haier, and Hotpoint top-mount refrigerators. Verify the complete appliance model number before ordering.
Common Problems This Part May Fix
Torn or cracked freezer door gasket
Visible gaps around the freezer door
Frost or moisture near the door opening
Warm air entering the freezer compartment
Freezer door does not seal tightly
Refrigerator runs longer because of an air leak
Replaces and Cross-References
WR14X29279, 312240100333, AP6328743, AGE28324, PD00077451
Cross-reference numbers are provided for identification. Always verify fit by complete appliance model number.
Compatibility
Compatible with select GE, Haier, and Hotpoint compact top-mount refrigerators. Verified model examples include:
HA10TG21BSW
HA10TG21CSW
HA10TG21SW
HA12TG21SW
HPS10LGVBRWW
VPS10FGMAWW
VPS10FGMBWW
VPS10FGMCWW
Partial model list only. Similar refrigerators may use a different fresh-food or freezer gasket depending on cabinet size, door color, and production revision.
Key Features
Genuine GE OEM replacement part
Freezer door gasket / magnetic seal
White finish
Helps prevent warm-air infiltration
Designed for select GE, Haier, and Hotpoint refrigerators
Factory-fit replacement for compatible models
Product Specifications
Part Number: WR14X29279
Brand: GE Appliances
Part Type: Freezer Door Gasket
Color: White
Condition: New
Quality: Genuine OEM
Package Quantity: 1 Gasket
Installation Notes
Unplug the refrigerator before service.
Temporarily move food to a safe cold location while the freezer door is open.
Remove the original gasket according to the appliance service procedure.
Install the replacement evenly around the door perimeter, making sure all corners and edges are fully seated.
Close the door and inspect the entire perimeter for gaps.
Shipping crease tip: If the gasket arrives folded or creased, warm it gently with warm water or a hair dryer on low heat, then allow it to relax into shape. Do not overheat the gasket.
Frequently Asked Questions
Is WR14X29279 the freezer gasket or refrigerator-door gasket?
WR14X29279 is the freezer door gasket. The fresh-food door can use a different gasket on the same refrigerator.
Is this Genuine GE OEM?
Yes. WR14X29279 is a Genuine GE Appliances replacement part.
Is the gasket white?
Yes. This part is the white freezer-door gasket version.
Can I install it if it arrives with folds?
Yes. Shipping folds can usually be relaxed by gently warming the gasket before installation.
Shop With Confidence
For best results, compare your complete refrigerator model number before ordering. Door gaskets can look nearly identical while differing in size, magnetic profile, color, or mounting design.
Genuine GE OEMFreezer Door GasketWhiteCompatibility Support
