Search results for "hvac caacitor"

W10503278 Refrigerator Control Board Refrigerator electronic (JAZZ) control board. Be aware the board will need to programmed after installation to work properly Replaces Part Numbers: WPW10503278, 12784415, W10503278, 12002339, 12002445, 12002449, 12002508, 12002509, 12002567, 12002706, 12784415V, 12868502, 12868510, 12868513, 2684578, 67003867, 67004453, 67004496, 67004907, 67005043, 67005280, 67005281, 67006034, 67006209, 67006214, 67006216, 67006226, 67006712, 67006740, 8208187, AP6022400, PS11755733, W10165748. Description: This Electronic Control Board is a replacement part for Specific Maytag, Whirlpool refrigerator models. This Electronic (JAZZ) Control Board manages various functions of your refrigerator, ensuring proper temperature control and operation. This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO 5303918214 Refrigerator Defrost Thermostat The XPARTCO 5303918214 is an aftermarket replacement defrost thermostat kit for Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators — commonly used on side-by-side and French door models equipped with an ice maker. This thermostat monitors the temperature of the evaporator coils: when the coils drop below a set temperature, it allows power to reach the defrost heater so frost can be cleared; once the coils warm back up, it cuts power to the heater again, protecting the evaporator from being overheated during that process. The most common reasons this thermostat gets replaced are a classic pair of symptoms: the freezer stays cold while the fresh food refrigerator section runs warm, or the refrigerator simply isn't defrosting on its normal cycle. Because this thermostat sits behind the rear access panel near the ice maker on many compatible models, replacing it typically involves removing the ice maker and the back panel to reach it — a more involved repair than a thermostat mounted in an easily accessible spot. It directly replaces AP2150145, 892545, AH469522, EA469522, PS469522, and 75303918214. Quick Answer The XPARTCO 5303918214 Refrigerator Defrost Thermostat fixes Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators where the freezer stays cold but the fresh food section runs warm, or the refrigerator isn't defrosting on its normal cycle. Replaces AP2150145, 892545, AH469522, EA469522, PS469522, 75303918214. This is a separate part from our 5303918202 defrost thermostat listing — the two fit different model groups and are not interchangeable. Installation on many compatible models requires removing the ice maker to access the thermostat. Common Problems This Part Fixes Freezer stays cold but the fresh food refrigerator section runs warm Refrigerator not defrosting on its normal cycle Excessive frost or ice buildup on the evaporator coils Refrigerator or freezer not cooling properly overall Water leaking inside the refrigerator from melting ice buildup Refrigerator running constantly as ice-caked coils reduce cooling efficiency Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator defrost thermostat directly replaces the following OEM and cross-reference part numbers: 5303918214, 75303918214, 892545, AH469522, EA469522, AP2150145, 240372703, 39TVE31, EAP469522, PS469522, AFR16819, PD00000354, L47-22F, SL8214, ER5303918214 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This defrost thermostat is compatible with select Frigidaire refrigerators, and also fits select Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators built on the same platform, including model numbers such as: FGHS2631PF4A, FGHS2655PF5A FGHC2331PFAA, FGHC2331PFCA FFHS2611PFEA, FFHS2611LBRA, FFHS2611LWMA, FFHS2622MSYA FFSS2614QS6A Note — not the same as 5303918202: This is a separate thermostat from our 5303918202 listing. The two fit different model groups and are not interchangeable, so always verify your full model number rather than assuming based on similar part number prefixes. Contact our support team with your model number if you're unsure which thermostat fits your refrigerator. Key Features Aftermarket replacement defrost thermostat kit for Frigidaire-platform refrigerators with an ice maker Monitors evaporator coil temperature and controls power to the defrost heater Resolves "freezer cold, fridge warm," "not defrosting on schedule," and "icy evaporator coils" symptoms caused by thermostat failure Ships with wiring diagram guidance for a correct connection Direct drop-in replacement — mounts to the original housing location Replaces AP2150145, 892545, AH469522, EA469522, PS469522, and 75303918214 Compatible with Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 5303918214 OEM Part Number 5303918214 Part Type Refrigerator Defrost Thermostat Kit Condition Aftermarket Replacement Function Monitors evaporator coil temperature and controls power to the defrost heater Typical Location Rear access panel area, near the ice maker on many compatible models Repair Difficulty Moderate — ice maker removal typically required for access Quantity 1 defrost thermostat kit Compatible Brands Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, Crosley Installation Notes ⚠️ Unplug Refrigerator And Shut Off Water Supply Before Starting Unplug the refrigerator from the wall outlet and turn off the water supply to the refrigerator before beginning. Wear work gloves. If your model has an ice maker, remove it first using a screwdriver to gain clearance for the next steps. Remove the back panel with a screwdriver to expose the defrost thermostat. Take out the existing thermostat and disconnect its wiring, labeling or photographing each connection first. Install the new 5303918214 thermostat by connecting the wires according to the wiring diagram provided with the kit, then secure the thermostat to the main housing using the small mounting screws. Reinstall the back panel, plug the refrigerator back in, turn the water supply back on, and reinstall the ice maker. Test the refrigerator over the following day to confirm both compartments are cooling evenly and the defrost cycle is running normally. Tools needed: screwdriver, wire cutters/strippers, work gloves. Frequently Asked Questions Do I really need to remove the ice maker for this repair? On many compatible models, yes — the thermostat sits behind the rear access panel in an area that the ice maker partially blocks, so removing it first gives you the clearance needed to reach the panel and the thermostat behind it. It's an extra step compared to some simpler defrost thermostat replacements, but it's a standard part of this particular repair. My freezer is cold but the fridge is warm. Is this the thermostat? Yes, this is the classic symptom of a failed defrost thermostat. When it fails, the defrost heater can't run correctly to clear frost from the evaporator coil, and the resulting ice buildup blocks the airflow that's supposed to carry cold air to the fresh food compartment. The freezer, sitting closer to the coil, often stays reasonably cold, while the fresh food side runs warm since it depends on that circulated air. I replaced the thermostat but my freezer temperature is still fluctuating. What should I check next? Replacing this thermostat resolves the issue for most customers, but if fluctuation continues, it's worth checking the other components in the same defrost circuit — the defrost timer and defrost heater — since a failure in either of those can produce similar temperature instability even with a good thermostat installed. It's also worth confirming the door seals are sealing properly, since a poor seal lets warm air in and can cause temperature swings unrelated to the defrost system. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire OEM part, but is manufactured to match the temperature threshold, mounting configuration, and function of the original 5303918214 defrost thermostat used in compatible Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 4681JB1029D Refrigerator Condenser Fan Motor – Compatible with LG and Kenmore Refrigerators Product Description Keep your refrigerator running efficiently with the XPARTCO 4681JB1029D Refrigerator Condenser Fan Motor. This Condenser Fan Motor is a replacement part for specific LG, Kenmore refrigerator models. This motor is responsible for powering the fan that cools the condenser coils, which helps dissipate heat from the refrigerator. Proper functioning of the condenser fan motor is crucial for maintaining the efficiency and cooling performance of the refrigerator. Replaces Part Numbers 4681JB1029D, EAU61644104, 4681JB1029Q, 1267566, AH3523330, EA3523330, PD00008709, AP4437783, PS3523330. Compatibility This replacement condenser fan motor fits select LG and Kenmore refrigerators. Example compatible models include (but are not limited to): LG LFX25974ST, LG LFX28968ST, and Kenmore 795.71053.010. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM performance for LG refrigerators 🌬️ Reliable Airflow – Circulates air over coils to prevent overheating and improve efficiency 💰 Cost-Effective Fix – Quality replacement at a lower cost than OEM parts 🛠️ DIY Installation – Plug-and-play wiring connector for easy setup 🛡️ Fixes Common Issues – Solves overheating, loud operation, or poor cooling problems 📐 Product Specification Part Number: 4681JB1029D Component Type: Refrigerator Condenser Fan Motor Assembly Material: Metal motor housing with plastic fan blade Mounting: Direct-fit on rear compressor compartment bracket Operating Conditions: Designed for continuous operation in refrigerator environments Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver, pliers ⚠️ Safety First: Always unplug the refrigerator before performing any repairs to prevent electrical shock. Steps: Disconnect power and pull refrigerator away from wall. Remove the rear access panel to expose the condenser area. Disconnect wiring harness and remove the old fan motor. Mount the new 4681JB1029D motor using the same screws. Reconnect the wiring harness and reinstall the rear panel. Plug in the refrigerator and confirm proper fan operation. ⏱️ Time Required: 20–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Keep your refrigerator cool and efficient — Add to Cart Now for a reliable, budget-friendly replacement!

Read more less

DD94-01031A Dishwasher Duct Condensor Assembly   Replaces Part Numbers: DD94-01031A, 4001433, AP5586892, PS4222729.      California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO 4681JB1029B Refrigerator Condenser Fan Motor 13Vdc, 1.55W, 120mA, CCW. Fits specific LG refrigerator models. Replaces Part Numbers: 4681JB1029B, 4681JB1017B, 4681JB1017E, 4681JB1027B, AP4437343, OEM17749374, PS3523329. Description: This Condenser Fan Motor is a replacement part for specific LG, Kenmore refrigerator models. This motor is responsible for powering the fan that cools the condenser coils, which helps dissipate heat from the refrigerator. Proper functioning of the condenser fan motor is crucial for maintaining the efficiency and cooling performance of the refrigerator.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO 2188820 Refrigerator Thermistor (Sensor) Replaces WP2188820 The XPARTCO 2188820 is an aftermarket replacement refrigerator temperature sensor (thermistor) compatible with select Whirlpool, Kenmore, KitchenAid, Maytag, Jenn-Air, Dacor, and Thermador refrigerators. The thermistor is an NTC (negative temperature coefficient) sensor that continuously monitors the air temperature inside the refrigerator or freezer compartment and sends resistance-based readings to the electronic control board. The control board uses these readings to regulate compressor run time and fan operation, maintaining the set temperature accurately and efficiently. This thermistor features an NTC resistance of 50K ohms at 25°C (27K ohms at 0°C/32°F) and a standard wire length of approximately 5.3 inches (13.46 cm), compatible with low-voltage refrigerator control boards (5V/12V). It directly replaces WP2188820, 2213442, AP6006068, PS11739132, and 1057764. Note: this thermistor is compatible with non-WISE system refrigerators only — it is not compatible with newer Whirlpool refrigerators using the WISE (Whirlpool Intelligent Smart Energy) control system. Installs in under 15 minutes. Quick Answer The XPARTCO 2188820 Refrigerator Thermistor fixes Whirlpool-family refrigerators that are too warm, too cold, have erratic temperatures, run the compressor too long, or display temperature-related error codes. NTC sensor, 50K ohm at 25°C, ~5.3" wire. Non-WISE system models only. Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Jenn-Air, Dacor, and Thermador. Replaces WP2188820, 2213442, AP6006068, PS11739132. Common Problems This Part Fixes Refrigerator not maintaining set temperature — too warm or too cold Freezer section too warm or food not freezing properly Compressor running continuously without cycling off Temperature fluctuating erratically despite stable ambient conditions Refrigerator temperature-related error codes displayed on the control panel Excessive frost buildup caused by incorrect temperature regulation Food or beverages freezing in the fresh food section Replaces Part Numbers This refrigerator thermistor directly replaces the following OEM and cross-reference part numbers: WP2188820, 2188820, 2213442, EAP11739132, AWP46934, PD00033406, AP6006068, PS11739132. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermistor is compatible with select refrigerators from the following brands and series: Whirlpool refrigerators — 5VW, GC3, EC3, GC5 series Kenmore / Sears refrigerators — 106 series (Whirlpool-built models) KitchenAid refrigerators — KSCS, KSSS, JS series Maytag refrigerators (select models) Jenn-Air refrigerators (select models) Dacor refrigerators (select models) Thermador refrigerators (select models) Important — WISE System Compatibility: The 2188820 thermistor is compatible with non-WISE system refrigerators only. It is not compatible with newer Whirlpool refrigerators equipped with the WISE (Whirlpool Intelligent Smart Energy) control system. If your refrigerator uses the WISE system, this thermistor will not work correctly. Verify your model number before ordering, or contact our support team to confirm compatibility. Key Features NTC (negative temperature coefficient) thermistor — resistance decreases as temperature increases, allowing precise temperature monitoring 50K ohm resistance at 25°C (27K ohm at 0°C/32°F) — matches original WP2188820 specifications Wire length approximately 5.3 inches (13.46 cm) — standard length matching OEM dimensions Low-voltage design compatible with 5V/12V refrigerator control boards Continuously sends temperature readings to the control board to regulate compressor and fan operation Non-WISE system compatible only — verify your model before ordering Direct replacement for WP2188820, 2213442, AP6006068, and PS11739132 Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Jenn-Air, Dacor, and Thermador refrigerators Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in under 15 minutes Product Specifications Part Number 2188820 OEM Part Number WP2188820 Part Type Refrigerator Temperature Sensor (NTC Thermistor) Condition Aftermarket Replacement Sensor Type NTC (Negative Temperature Coefficient) Resistance at 25°C 50,000 ohms (50K ohm) Resistance at 0°C (32°F) 27,000 ohms (27K ohm) Wire Length Approximately 5.3 inches (13.46 cm) Voltage 5V / 12V (low voltage) WISE System Compatibility Non-WISE models only Compatible Brands Whirlpool, Kenmore, KitchenAid, Maytag, Jenn-Air, Dacor, Thermador Installation Notes ⚠️ Unplug Refrigerator Before Starting Disconnect power before beginning. The thermistor location varies by model — it is typically clipped to a bracket on the interior side wall of the fresh food or freezer compartment, or mounted near the evaporator coil. Consult your model's parts diagram or service manual to confirm the exact location before disassembly. Open the sensor cover or unclip the sensor bracket, disconnect the wiring connector, and pull the old thermistor out. Insert the new 2188820 thermistor, reconnect the wiring connector, and snap the cover or bracket back into place. Ensure the sensor head is positioned close to the compartment wall and the wiring is not pinched. Restore power and monitor the refrigerator temperature over the next few hours to confirm stable, accurate cooling. Tools needed: Phillips screwdriver (for panel access on some models); no tools needed for sensor replacement itself. Frequently Asked Questions What is the difference between 2188820 and WP2188820? These are the same thermistor. WP2188820 is the updated Whirlpool OEM part number that superseded the original 2188820. The 2213442 is also a cross-reference for the same part. This aftermarket replacement is compatible with all three numbers. What does an NTC thermistor do and how do I know if mine has failed? An NTC thermistor is a resistor whose resistance decreases as temperature increases. The control board sends a small voltage through the thermistor and measures the resulting resistance — a lower resistance means warmer temperature, and a higher resistance means cooler temperature. The board uses this reading to decide when to run the compressor and fans. A failed thermistor either reads open circuit (no continuity), short circuit (zero resistance), or provides incorrect readings that cause the refrigerator to run too warm, too cold, or cycle erratically. Test with a multimeter at room temperature — a working 2188820 should read approximately 50K ohms at 25°C (77°F). Significant deviation indicates failure. How do I know if my refrigerator uses the WISE system? The WISE (Whirlpool Intelligent Smart Energy) system was introduced on newer Whirlpool refrigerator models and uses a different thermistor specification that is not interchangeable with the 2188820. Models that use the WISE system are typically marked in the product documentation or on the control board. The easiest way to confirm compatibility is to verify your model number with our support team before ordering, or check whether WP2188820 appears in your model's official parts diagram. If your parts diagram lists WP2188820, this replacement is compatible. Where is the thermistor located in my refrigerator? The thermistor location varies by model and brand. On Whirlpool and KitchenAid models, it is commonly found on the interior side wall of the fresh food compartment clipped to a plastic housing. On some models it is located near the evaporator coil behind the freezer back panel. On Kenmore 106 series models, it may be on the fresh food section wall or inside the back panel. Consult your specific model's parts diagram or search for a model-specific installation video to locate the sensor before disassembling the refrigerator. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured with an NTC thermistor rated to the same 50K ohm specification as the original WP2188820 to match the performance and accuracy of the factory sensor. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

5303918214 Genuine OEM Frigidaire Refrigerator Defrost Thermostat The 5303918214 is a genuine Frigidaire OEM defrost thermostat kit for Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators — commonly used on side-by-side and French door models equipped with an ice maker. This thermostat monitors the temperature of the evaporator coils: when the coils drop below a set temperature, it allows power to reach the defrost heater so frost can be cleared; once the coils warm back up, it cuts power to the heater again, protecting the evaporator from being overheated during that process. The most common reasons this thermostat gets replaced are a classic pair of symptoms: the freezer stays cold while the fresh food refrigerator section runs warm, or the refrigerator simply isn't defrosting on its normal cycle. Because this thermostat sits behind the rear access panel near the ice maker on many compatible models, replacing it typically involves removing the ice maker and the back panel to reach it — a more involved repair than a thermostat mounted in an easily accessible spot. It directly replaces AP2150145, 892545, AH469522, EA469522, PS469522, and 75303918214. As a genuine OEM part, the 5303918214 is manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. Quick Answer The 5303918214 Genuine OEM Frigidaire Refrigerator Defrost Thermostat fixes Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators where the freezer stays cold but the fresh food section runs warm, or the refrigerator isn't defrosting on its normal cycle. Replaces AP2150145, 892545, AH469522, EA469522, PS469522, 75303918214. This is a separate part from our 5303918202 defrost thermostat listing — the two fit different model groups and are not interchangeable. Installation on many compatible models requires removing the ice maker to access the thermostat. Common Problems This Part Fixes Freezer stays cold but the fresh food refrigerator section runs warm Refrigerator not defrosting on its normal cycle Excessive frost or ice buildup on the evaporator coils Refrigerator or freezer not cooling properly overall Water leaking inside the refrigerator from melting ice buildup Refrigerator running constantly as ice-caked coils reduce cooling efficiency Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator defrost thermostat directly replaces the following OEM and cross-reference part numbers: 5303918214, 75303918214, 892545, AH469522, EA469522, AP2150145, 240372703, 39TVE31, EAP469522, PS469522, AFR16819, PD00000354, L47-22F, SL8214, ER5303918214 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This defrost thermostat is compatible with select Frigidaire refrigerators, and also fits select Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators built on the same platform, including model numbers such as: FGHS2631PF4A, FGHS2655PF5A FGHC2331PFAA, FGHC2331PFCA FFHS2611PFEA, FFHS2611LBRA, FFHS2611LWMA, FFHS2622MSYA FFSS2614QS6A Note — not the same as 5303918202: This is a separate thermostat from our 5303918202 listing. The two fit different model groups and are not interchangeable, so always verify your full model number rather than assuming based on similar part number prefixes. Contact our support team with your model number if you're unsure which thermostat fits your refrigerator. Key Features Genuine Frigidaire OEM part — factory-specified temperature threshold and mounting configuration Defrost thermostat kit for Frigidaire-platform refrigerators with an ice maker Monitors evaporator coil temperature and controls power to the defrost heater Resolves "freezer cold, fridge warm," "not defrosting on schedule," and "icy evaporator coils" symptoms caused by thermostat failure Ships with wiring diagram guidance for a correct connection Direct drop-in replacement — mounts to the original housing location Replaces AP2150145, 892545, AH469522, EA469522, PS469522, and 75303918214 Compatible with Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 5303918214 Part Type Refrigerator Defrost Thermostat Kit Condition Genuine OEM Function Monitors evaporator coil temperature and controls power to the defrost heater Typical Location Rear access panel area, near the ice maker on many compatible models Repair Difficulty Moderate — ice maker removal typically required for access Quantity 1 defrost thermostat kit Compatible Brands Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, Crosley Installation Notes ⚠️ Unplug Refrigerator And Shut Off Water Supply Before Starting Unplug the refrigerator from the wall outlet and turn off the water supply to the refrigerator before beginning. Wear work gloves. If your model has an ice maker, remove it first using a screwdriver to gain clearance for the next steps. Remove the back panel with a screwdriver to expose the defrost thermostat. Take out the existing thermostat and disconnect its wiring, labeling or photographing each connection first. Install the new 5303918214 thermostat by connecting the wires according to the wiring diagram provided with the kit, then secure the thermostat to the main housing using the small mounting screws. Reinstall the back panel, plug the refrigerator back in, turn the water supply back on, and reinstall the ice maker. Test the refrigerator over the following day to confirm both compartments are cooling evenly and the defrost cycle is running normally. Tools needed: screwdriver, wire cutters/strippers, work gloves. Frequently Asked Questions Do I really need to remove the ice maker for this repair? On many compatible models, yes — the thermostat sits behind the rear access panel in an area that the ice maker partially blocks, so removing it first gives you the clearance needed to reach the panel and the thermostat behind it. It's an extra step compared to some simpler defrost thermostat replacements, but it's a standard part of this particular repair. My freezer is cold but the fridge is warm. Is this the thermostat? Yes, this is the classic symptom of a failed defrost thermostat. When it fails, the defrost heater can't run correctly to clear frost from the evaporator coil, and the resulting ice buildup blocks the airflow that's supposed to carry cold air to the fresh food compartment. The freezer, sitting closer to the coil, often stays reasonably cold, while the fresh food side runs warm since it depends on that circulated air. I replaced the thermostat but my freezer temperature is still fluctuating. What should I check next? Replacing this thermostat resolves the issue for most customers, but if fluctuation continues, it's worth checking the other components in the same defrost circuit — the defrost timer and defrost heater — since a failure in either of those can produce similar temperature instability even with a good thermostat installed. It's also worth confirming the door seals are sealing properly, since a poor seal lets warm air in and can cause temperature swings unrelated to the defrost system. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original temperature threshold, mounting configuration, and function of the defrost thermostat originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO BPV-31 Refrigerator Refrigerant Piercing Valve / Line Tap Valve Kit The XPARTCO BPV-31 is a universal bullet piercing tap valve (line tap valve) used to quickly access a sealed refrigerant line on refrigerators, freezers, window air conditioners, dehumidifiers, and other HVAC systems — without soldering or brazing. The valve clamps around a copper refrigerant line and, when the valve stem is tightened with the included hex key, a hardened piercing needle punctures the tubing to create an access port. This lets a technician connect a charging hose or gauge to check pressure, pull a vacuum, or add refrigerant to a system that has no factory service port. It's a staple tool for appliance service and DIY refrigerator/freezer repair. Fits 1/4", 5/16", and 3/8" outside diameter copper pipes with the included adapters. The access port connection is a 1/4" male flare fitting. Rated to 500 PSI maximum, with a patented permanent gasket providing over 180 inch-lbs of sealing force — around 50 times the sealing area of a standard O-ring type valve — pressure tested at 250°F. Corrosion-resistant metal (zinc alloy) construction with a piercing needle engineered for concentricity and hardness to seat perfectly every time. Non-positional mounting requires no separate adapter valve and only 2" of clearance for installation. Each kit includes the piercing valve, a hex key wrench, and 2 adapters. It replaces AP4502525, BPV31, BPV31D, GPV14, GPV31, GPV38, GPV56, and MPV31. Quick Answer The XPARTCO BPV-31 Refrigerant Piercing Valve Kit taps into a sealed copper refrigerant line to add refrigerant, check pressure, or pull a vacuum — no soldering required. Fits 1/4", 5/16", and 3/8" OD pipes. 1/4" male flare port connection. 500 PSI max, patented gasket (50x the sealing area of an O-ring). Zinc alloy metal. Includes piercing valve, hex key, and 2 adapters; only needs 2" clearance. Replaces AP4502525, BPV31, BPV31D, GPV14, GPV31, GPV38, GPV56, MPV31. Not suitable for R410a systems. Common Uses This Kit Serves Adding refrigerant to a refrigerator or freezer that has no factory service port Checking system pressure on a sealed refrigerant line for diagnostics Pulling a vacuum on a system during service Recharging window air conditioners and dehumidifiers Confirming whether a sealed system has lost its refrigerant charge (leak diagnosis) Providing temporary or service access to copper refrigerant tubing without brazing Reviving a garage/shop refrigerator or freezer that has slowly lost its charge Accessing R-12, R-22, R-134a, and other compatible refrigerant systems (NOT R410a) Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This bullet piercing tap valve directly replaces the following OEM and cross-reference part numbers: BPV-31, BPV31, BPV31D, AP4502525, GPV14, GPV31, GPV38, GPV56, MPV31 The BPV-31 is a universal valve that covers the GPV-series (GPV14, GPV31, GPV38, GPV56) and MPV31 across the pipe sizes they individually served. Contact our support team if you need help confirming the correct valve for your line size. Compatibility This bullet piercing valve is a universal tool compatible with sealed refrigerant systems using copper tubing, including: Refrigerators and freezers — all major brands with 1/4", 5/16", or 3/8" OD copper refrigerant lines Window air conditioners — for recharging and pressure checks Dehumidifiers — sealed refrigerant systems Other HVAC systems with compatible copper line sizes Refrigerant compatibility — works with R-12, R-22, R-134a and other common refrigerants Important — NOT for R410a Systems: This BPV-31 piercing valve is NOT rated for R410a refrigerant systems, which operate at significantly higher pressures than the valve's design allows. Using it on an R410a system is unsafe. Before use, confirm your line's outside diameter (1/4", 5/16", or 3/8") and select the correct included adapter. Verify the pipe size before installation. Key Features Bullet piercing tap valve — taps a sealed copper refrigerant line to create an access port without soldering or brazing Fits 1/4", 5/16", and 3/8" outside diameter copper pipes (with included adapters) 1/4" male flare access port connection for charging hoses and gauges 500 PSI maximum pressure rating Patented permanent gasket — over 180 inch-lbs of sealing force, ~50 times the sealing area of a standard O-ring type valve; pressure tested at 250°F Piercing needle engineered for concentricity and hardness to seat perfectly every time Corrosion-resistant zinc alloy metal construction — won't rust or wear out over time Non-positional mounting — no separate adapter valve required, installs in any orientation Compact design needs only 2" of clearance for installation and use Each kit includes: 1 piercing valve, 1 hex key wrench, 2 adapters Replaces AP4502525, BPV31, BPV31D, GPV14, GPV31, GPV38, GPV56, and MPV31 NOT suitable for R410a refrigerant systems Product Specifications Part Number XPBPV-31 Part Type Bullet Piercing Tap Valve (Line Tap Valve Kit) Condition Aftermarket Replacement Application Refrigerators, Freezers, Window AC, Dehumidifiers, HVAC (sealed copper lines) Compatible Pipe Sizes 1/4", 5/16", 3/8" outside diameter Port Connection 1/4" Male Flare Maximum Pressure 500 PSI Sealing Force 180+ inch-lbs (patented gasket, ~50x O-ring sealing area) Pressure Tested 250°F Material Corrosion-resistant zinc alloy metal Mounting Non-positional, 2" clearance required Kit Includes 1x Piercing Valve, 1x Hex Key, 2x Adapters Not Compatible With R410a refrigerant systems Installation Notes ⚠️ Refrigerant Safety Warning Working with sealed refrigerant systems can expose you to pressurized refrigerant, which can cause frostbite, eye injury, and other harm. Wear safety glasses and protective gloves before piercing any line. Refrigerant handling may be regulated in your area — certain refrigerants require EPA certification (in the US) to purchase and handle. Never vent refrigerant to the atmosphere. This valve is NOT rated for R410a systems (too high pressure). If you're not experienced with refrigerant systems, have this work done by a qualified HVAC or appliance technician. ⚠️ Installation Steps — Clean the Line First Put on safety glasses and protective gloves. Identify the copper line you want to tap and confirm its outside diameter (1/4", 5/16", or 3/8") so you can select the correct included adapter. Clean the section of pipe where the valve will mount to prevent debris from entering the refrigerant line. Ensure the composite seal "O" ring/gasket is properly in place inside the valve. Place the two halves of the valve saddle around the pipe using the appropriate adapter insert for your pipe size. Install and evenly tighten the socket-head screws to clamp the valve body firmly around the pipe. To pierce the line, turn the valve stem clockwise with the included hex key until the needle punctures the tubing, then back the stem out (counterclockwise) to open the port and allow flow. To connect a gauge or charging hose: remove the cap, attach your hose to the 1/4" flare port, and open the valve by turning the stem counterclockwise. When finished, close the valve (turn the stem clockwise) BEFORE disconnecting the hose, then reinstall the protective cap. Note: the compact valve needs only 2" of clearance around the pipe. Tools needed: Included hex key wrench, safety glasses, protective gloves. (Note: to attach a gauge directly to the BPV, a retrofit valve adapter may be required — not included.) Frequently Asked Questions What is a bullet piercing valve used for? A bullet piercing valve (line tap valve) lets you tap into a sealed copper refrigerant line to create an access port — without cutting, soldering, or brazing the line. Most household refrigerators and freezers are sealed systems with no factory service port, so if you need to check the refrigerant pressure, pull a vacuum, or add refrigerant, a piercing valve gives you that access quickly. It clamps around the pipe, and a needle pierces the tubing when you tighten the valve stem. It's commonly used in appliance repair and HVAC service, and by DIYers reviving a garage refrigerator or freezer that has lost its charge. Which pipe sizes does this fit? The BPV-31 fits 1/4", 5/16", and 3/8" outside diameter copper pipes using the included adapters. Before installing, measure or confirm your refrigerant line's outside diameter and select the matching adapter insert. Getting the size right is essential for a proper seal — an incorrectly sized adapter won't clamp tightly and can leak. If you're not sure of your line size, measure the outside diameter of the copper tubing with calipers or a pipe gauge. Can I use this on an R410a system? No — the BPV-31 is NOT rated for R410a refrigerant systems. R410a operates at significantly higher pressures than older refrigerants like R-12, R-22, and R-134a, and exceeds the safe working pressure of this valve (500 PSI max). Using it on an R410a system is unsafe and could result in valve failure or refrigerant release. This valve is appropriate for lower-pressure systems using R-12, R-22, R-134a, and similar refrigerants. For R410a systems, use service equipment specifically rated for R410a pressures. Is a piercing valve a permanent solution? Piercing valves are best thought of as a service-access tool rather than a permanent fixture. They work reliably for tapping into a line to diagnose, vacuum, or charge a system, and the BPV-31's patented gasket provides a much stronger seal than basic O-ring valves. However, for a long-term permanent service port, many technicians prefer to cut the line and braze in a proper Schrader service port. Some technicians have concerns about the very long-term sealing of any piercing valve left permanently on a line. If you leave the valve installed, make sure the stem is closed and the cap is in place, and check periodically for leaks. Do I need EPA certification to add refrigerant? In the United States, handling many refrigerants (and purchasing them) requires EPA Section 608 certification, and it is illegal to intentionally vent refrigerant to the atmosphere. Regulations vary by refrigerant type and jurisdiction. The piercing valve itself is a tool that anyone can install, but the refrigerant handling that follows may be regulated. If you're a DIYer, research the rules that apply to your specific refrigerant and location, or have the refrigerant work done by a certified technician. Always recover refrigerant properly rather than venting it. Is this an OEM or aftermarket part? This is an aftermarket universal service tool built to OEM-equivalent quality standards. The BPV-31 is a universal industry-standard bullet piercing valve design (also sold as Supco BPV31 and equivalent), manufactured from corrosion-resistant zinc alloy to match the fit, 1/4"/5/16"/3/8" pipe compatibility, 1/4" flare port, 500 PSI rating, and patented-style sealing gasket of the standard BPV-31 line tap valve. It replaces AP4502525, BPV31D, GPV14, GPV31, GPV38, GPV56, and MPV31. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

4TM-B12 Refrigerator / Freezer Compressor Overload 1/2 HP Refrigerator / Freezer Thermal Overload Protector 1/2 HP (375W) - 110V 4TM-B   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO WR60X10307 Refrigerator Evaporator Fan Motor The XPARTCO WR60X10307 is an aftermarket replacement evaporator fan motor designed to circulate cold air throughout the refrigerator and freezer compartments. Restore efficient cooling with the replacement XPARTCO WR60X10307 Refrigerator Evaporator Fan Motor. This evaporator fan motor is designed for select GE, Hotpoint, RCA, and Kenmore refrigerators, circulating air over the evaporator coils to maintain consistent temperatures in both refrigerator and freezer compartments. It includes a 6-pin harness with a 2-wire thermistor, addressing issues like noisy operation, inconsistent temperatures, or frost buildup, offering a cost-effective alternative to OEM parts. When the fan motor fails, cold air cannot circulate effectively, leading to warm refrigerator sections, frost buildup, or noisy operation. Replacing the evaporator fan motor restores airflow, improves cooling efficiency, and helps prevent food spoilage. Quick Answer The XPARTCO WR60X10307 Evaporator Fan Motor fixes refrigerators that are not cooling properly, have warm fresh food sections, or make unusual buzzing or grinding noises. It restores proper air circulation inside the unit. Common Problems This Part Fixes Refrigerator not cooling properly Freezer cold but fridge section warm Loud buzzing, humming, or grinding noise Frost buildup around evaporator coils Inconsistent temperature between compartments No airflow from vents Replaces Part Numbers This evaporator fan motor replaces the following part numbers: WR60X10307, WR60X10099, WR60X10224, WR60X30370, 197D4968G009, FDQT26GE6, AGE29301, PD00001317, EAP2364950, AP4438809, 1550741, PS2364950 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This evaporator fan motor is compatible with select refrigerators from the following brands: GE refrigerators Hotpoint refrigerators Other compatible models using WR60X10307 Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. Key Features Circulates cold air across evaporator coils Restores proper airflow and temperature balance Offers OEM-equivalent performance at a lower price. Reduces noise from worn or failing fan motors Improves overall cooling efficiency Direct replacement for WR60X10307 motor, evaporator fan motor, 9.75V DC, 3.25W, includes 6-pin harness with 2-wire thermistor. Product Specifications Part Number XPARTCO WR60X10307 Part Type Evaporator Fan Motor Application Refrigerator / Freezer Condition Aftermarket Replacement Function / Specs Air Circulation, 9.75V DC, 3.25W Compatible Brands GE, Hotpoint Installation Notes ⚠️ Safety First — Disconnect Power Before Service Unplug the refrigerator before servicing. Access the evaporator fan by removing the rear freezer panel. Disconnect wiring harness and mounting screws, replace the fan motor, and reassemble. Ensure the fan spins freely before restoring power. Frequently Asked Questions What does the evaporator fan motor do? It circulates cold air from the evaporator coils throughout the refrigerator and freezer compartments to maintain even cooling. Will this fix a warm refrigerator section? Yes, a failed evaporator fan motor is a common cause of warm fridge sections while the freezer remains cold. Is this an OEM part? This is a high-quality aftermarket replacement built to OEM-equivalent standards for reliable performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in high-quality replacement parts. Fast shipping from our U.S. warehouse and expert support available to help verify compatibility. ✓ Fast US Shipping ✓ Quality Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 4681JB1029A Refrigerator Evaporator Fan Motor – Compatible with LG and Kenmore Refrigerators Product Description Keep your refrigerator cooling evenly with the XPARTCO 4681JB1029A Refrigerator Evaporator Fan Motor. This Fan Motor is a replacement component for specific LG, Kenmore refrigerator models. It operates the circulation fan located in the back of the refrigerator compartment, distributing cool air evenly throughout. The motor enables constant airflow across shelves and compartments to maintain consistent temperatures and humidity levels. Causes of a bad fan motor include failure of bearings or windings due to prolonged use. Replaces Part Numbers 4681JB1029A, EAU60694507, 1330410, 4681JB1010C, 4681JB1017A, 4681JB1017D, 4681JB1027A, EAU61762902, EAU41921810, PD00037982, EAP3523328, AH3523328, EA3523328, AP4438221, PS3523328.  Compatibility This replacement evaporator fan motor fits select LG and Kenmore refrigerators. Example compatible models include (but are not limited to): LG LFX25960ST, LG LFX28968ST, and Kenmore 795.77543600. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Built to meet OEM airflow and reliability standards ❄️ Efficient Air Circulation – Distributes cold air evenly through refrigerator and freezer 💰 Affordable Solution – Quality replacement at a lower cost than OEM parts 🛠️ DIY Installation – Simple plug-in wiring connector for quick installation 🛡️ Fixes Common Issues – Solves frost buildup, uneven cooling, or noisy fan problems 📐 Product Specification Part Number: 4681JB1029A Component Type: Refrigerator Evaporator Fan Motor Material: Metal motor housing with balanced plastic fan blade Mounting: Direct-fit replacement in freezer evaporator compartment Operating Conditions: Designed for continuous low-temperature operation Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the refrigerator before performing repairs to prevent electrical shock. Steps: Unplug the refrigerator. Remove shelves and freezer rear panel to access the evaporator area. Disconnect the wiring harness and mounting screws on the old fan motor. Install the new XPARTCO 4681JB1029A motor, reconnect wiring, and secure the panel. Restore power and verify quiet, consistent airflow. ⏱️ Time Required: 20–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore efficient, even cooling — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

30A Ceramic Line Fuse, Fast Blow, 6.35 x 32 mm Product Description Protect your appliances with the replacement 30A Ceramic Line Fuse, Fast Blow, 6.35 x 32 mm. This high-quality, fast-acting ceramic cartridge fuse is designed to safeguard circuits in appliances like microwaves, dryers, and HVAC systems by interrupting power during over-current events. With a 30A current rating, 250VAC/125VDC voltage rating, and compact 3AB/3AG (6.35 x 32 mm) size, it offers reliable protection for high-power loads. Constructed with a durable ceramic body for high interrupting ratings, this fuse ensures safety and performance. Note: Includes one fast-blow ceramic fuse; disconnect power before installation. Check appliance manual for compatibility. Replaces part numbers: ABC-30, BK/ABC-30, 0ADEC9300-BE, 0314030.MX52LP, BK-AHC-30-R, BK-AHCF-V-30-R Compatibility: Compatible with appliances including but not limited to: Microwaves: Select GE, Samsung, LG models requiring 30A, 250V fast-blow fuses. Dryers: GE Hotpoint models (e.g., compatible with WE1X21975 assemblies). HVAC Systems: Units using 3AB/3AG 6.35 x 32 mm fast-acting fuses. Other Appliances: Power strips, audio amplifiers, and industrial equipment requiring 30A protection. Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select GE, Samsung, LG, and other appliances using 3AB/3AG fuses. 🔥 Specifications: replacement ceramic fuse, 30A, 250VAC/125VDC, fast-blow, 6.35 x 32 mm (1/4" x 1-1/4"), ceramic body, 10kA interrupting rating at 125VAC, 3.7 mOhms resistance, UL Listed, RoHS compliant. 💰 Cost-Effective Alternative: replacement fuse offers OEM-equivalent performance at a lower cost. 🛠️ Easy Installation: Requires fuse holder or clip; typically installed in 5–10 minutes with basic tools. 🛡️ Reliable Fixes: Protects circuits from over-current, preventing appliance damage or failure. Installation Notes: Safety First: Disconnect the appliance from the power source before installation. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Ensure your appliances run safely and efficiently today! Add to cart now for a budget-friendly fix!

Read more less