Search results for "convection motor"

XPARTCO 2315549 Refrigerator Evaporator Fan Motor Replaces WP2315549 The XPARTCO 2315549 is an aftermarket replacement evaporator fan motor for Whirlpool-built side-by-side refrigerators, located in the freezer section. This small motor pulls cold air off the evaporator coil and pushes it through the duct system to both the freezer and fresh food compartments. Without it circulating air, the coil itself keeps getting cold, but that cold air never reaches your food — the freezer, being closest to the coil, may hold up reasonably well for a while, but the fresh food compartment depends entirely on ducted airflow and drifts warmer and warmer as circulation weakens or stops. This motor ships complete with its wiring harness, so nothing needs to be spliced or transferred from the old unit. Common failure modes include worn motor bearings that let the blade wobble or bind, ice buildup on the coil that jams the blade, and electrical failure of the motor windings. A simple way to check before ordering: with the refrigerator unplugged, try turning the fan blade by hand — it should spin freely with no grinding or resistance. It directly replaces WP2315549, 2220569, 1193008, AP6007250, PS11740362, and EAP11740362. Quick Answer The XPARTCO 2315549 Refrigerator Evaporator Fan Motor fixes Whirlpool-built side-by-side refrigerators with uneven cooling between compartments, frost buildup on the evaporator coil, unusual humming or buzzing noise, or a fresh food section that runs warmer than the freezer. Includes wiring harness. Replaces WP2315549, 2220569, 1193008, AP6007250, PS11740362, EAP11740362. Double-check the part number carefully — this is a different motor from our similarly numbered 2315539 listing, and the two are easy to mix up. Common Problems This Part Fixes Fresh food compartment running warmer than the freezer, or warmer than it used to Uneven temperatures between shelves or between the fresh food and freezer sides Frost or ice buildup accumulating on or around the evaporator coil Unusual humming, buzzing, or grinding noise coming from inside the freezer Noise that stops when the freezer door is opened and starts again once it's closed Refrigerator running constantly as the compressor tries to compensate for poor circulation Fan blade that doesn't spin freely, or spins with noticeable resistance, when checked by hand Fridge section too warm or too cold, freezer section too warm or too cold Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator evaporator fan motor directly replaces the following OEM and cross-reference part numbers: 2315549, WP2315549, 2220569, 1193008, AP6007250, AWP47338, PD00002704, PS11740362, EAP11740362, ESF-U2A If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This evaporator fan motor is compatible with select Whirlpool-built side-by-side refrigerators across the Whirlpool family of brands, including: Whirlpool side-by-side refrigerators Maytag, Amana, and KitchenAid refrigerators (select Whirlpool-built models) Jenn-Air, Admiral, Norge, and Roper refrigerators (select models) Inglis refrigerators (select models) Select Kenmore and Ikea refrigerators built on the Whirlpool platform Verified model numbers include: 7GS2FHAXTA02, 7GS5FHAXTA00, ED2DHEXWB00, and ED2DHEXWL00. Note — easy to confuse with 2315539: This part is 2315549, production number ESF-U2A. It is a separate, distinct motor from our 2315539 listing (production number ESF-U2B, replacing 2219689, 2225625, and W10438708), which serves a different set of models. The two part numbers differ by only a single transposed digit and are frequently mistyped or mixed up when ordering — double-check your old motor's part number or your appliance's full model number carefully before ordering. Contact our support team with your model number if you're unsure which motor you need. Key Features Aftermarket replacement evaporator fan motor with wiring harness included — nothing to splice or transfer Circulates cold air from the evaporator coil throughout the freezer and fresh food compartments Resolves "fresh food too warm," "uneven cooling," "frost buildup," and "humming or buzzing noise" symptoms caused by fan motor failure Direct drop-in replacement matching the original mounting and blade fitment Replaces WP2315549, 2220569, 1193008, AP6007250, PS11740362, and EAP11740362 Compatible with Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Admiral, Norge, Roper, Inglis, and select Kenmore refrigerators Aftermarket replacement built to OEM-equivalent quality standards Straightforward DIY repair — typically 15 to 30 minutes Product Specifications Part Number 2315549 OEM Part Number WP2315549 Production Number ESF-U2A Part Type Refrigerator Evaporator Fan Motor Condition Aftermarket Replacement Brand Whirlpool Location Freezer section, behind the rear panel near the evaporator coil Kit Contents Fan motor with wiring harness Application Side-by-Side Refrigerators Repair Difficulty Easy — 15 to 30 minutes Quantity 1 fan motor Compatible Brands Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Admiral, Norge, Roper, Inglis, Kenmore Installation Notes ⚠️ Unplug Refrigerator Before Starting — Let The Freezer Thaw If Iced Over Disconnect power at the outlet before beginning, and move all food from the freezer to a cooler for the duration of the repair. Wear work gloves. Access is through the freezer's rear interior panel: remove the shelving and bins as needed, then remove the screws securing the back panel and set it aside to expose the evaporator coil and fan assembly. If you see significant frost or ice buildup around the fan or coil, let the unit sit unplugged with the door open for a few hours, or run a manual defrost, before continuing — ice can be masking the actual failure and can make the old motor difficult to remove cleanly. Photograph the wiring harness connector and the fan blade's orientation before disconnecting anything. Unplug the motor's wiring harness connector, remove the mounting screws or clips holding the motor bracket in place, and carefully pull the motor and fan blade assembly free — on many models the blade is a separate piece that pulls off the motor shaft. Transfer the fan blade to the new motor if a blade isn't included, matching the original orientation. Mount the new 2315549 in the same position, reconnect the wiring harness connector fully, and confirm the blade spins freely by hand without contacting the housing before reassembling the back panel. Restore power and monitor both compartments over the next 24 hours to confirm even cooling has returned. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions How is this different from your 2315539 listing? The numbers look almost identical. They are genuinely different motors that happen to have nearly identical part numbers — 2315549 versus 2315539, just one transposed digit. This 2315549 motor carries production number ESF-U2A and replaces WP2315549, 2220569, and 1193008. Our separate 2315539 listing carries production number ESF-U2B and replaces a different set of numbers (2219689, 2225625, W10438708) for a different group of models. Because the numbers are so easy to mix up, we'd strongly recommend double-checking the exact number on your old motor, or your full refrigerator model number, before ordering either one. My freezer seems fine but the fresh food section is warm. Is this the fan motor? Yes, this is a very common and telling symptom pattern. The freezer compartment sits right next to the evaporator coil and can stay reasonably cold through simple proximity even with poor air circulation, but the fresh food compartment depends entirely on the fan pushing cold air through the ducting to reach it. When the fan motor fails or slows down, the fresh food side is usually the first and most noticeably affected area. How can I test the motor before ordering a replacement? With the refrigerator unplugged and the rear freezer panel removed, try turning the fan blade by hand. It should spin freely and smoothly with no grinding, binding, or resistance. If it doesn't turn freely, or doesn't turn at all, the motor has very likely failed. Also listen for humming or buzzing while the refrigerator is running — a motor trying and failing to turn often makes noise without actually moving air. There's a lot of frost around the fan and coil. Should I address that first? It's worth understanding which came first. Excess frost can be a cause of fan failure — a jammed, ice-bound blade can burn out the motor over time — or a result of it, since poor air circulation lets moisture condense and freeze unevenly around the coil area. Either way, thawing the ice out fully before installing the new motor makes the repair easier and lets you confirm the blade spins freely once everything is defrosted. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the mounting, wiring harness configuration, and airflow performance of the original WP2315549 evaporator fan motor used in compatible Whirlpool-built side-by-side refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DD31-00016A Dishwasher Drain Pump Motor The XPARTCO DD31-00016A is an aftermarket replacement BLDC (brushless DC) drain pump motor for Samsung dishwashers. This motor removes water from the dishwasher tub during the drain phase of the cycle — an impeller mechanism pumps water out through the drain hose, running during the draining phase to ensure a constant, steady flow and help prevent clogs. Weighs approximately 0.50 lbs, with package dimensions of 4.02" x 3.50" x 3.54". Compatible with 120V and 230V systems. Common causes of failure include worn motor bearings, electrical failure, or debris obstructing the impeller. Symptoms of a failing drain pump motor include water not draining from the tub, standing water left after a cycle, unusual noise during the drain phase, or intermittent draining problems that don't happen every cycle. It directly replaces AP5917178, 113121, 4000925, EAP9606350, PS9606350, ASM773863, PD00036475, and 045900194701. Quick Answer The XPARTCO DD31-00016A Dishwasher Drain Pump Motor fixes Samsung dishwashers that aren't draining, leave standing water after a cycle, make unusual noise during draining, or have intermittent draining problems. BLDC motor, 120V/230V, ~0.50 lbs. Replaces AP5917178, 113121, 4000925, EAP9606350, PS9606350, ASM773863, PD00036475, 045900194701. When removing the old motor, you'll need to hold a release tab open while twisting the motor counterclockwise at the same time — this two-handed step trips up a lot of first-time installers. Common Problems This Part Fixes Dishwasher not draining water from the tub Standing water left in the tub after a completed cycle Unusual noise during the drain phase Intermittent draining problems that don't occur every cycle Reduced water circulation and cleaning performance Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers: DD31-00016A, 113121, 4000925, AP5917178, ASM773863, EAP9606350, PD00036475, PS9606350 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Samsung dishwashers, including model numbers such as DW80R9950QH/AA, DW80B7070UG/AA, DW80R9950MT/AA, DW80B6061UG/AA, DW80R9950QN/AA, DW80B7070US/AA, DW80B6061US/AA, DW80B7071UG/AA, DW80B6060US/AA, DW80B6060UG/AA, DW80BB7070U1/AA, DW80B7070AP/AA, DW80B7071US/AA, DW80R7061UG/AA, DDW24T999BB/DA, DDW24M999UM/DA, DDW24T998US/DA, DDW24M999US/DA, DW60M9990AP, and DW80B6060UG. Note: This part is not a replacement for any earlier designation — per Samsung's own listing, DD31-00016A is a new part that doesn't supersede another part number. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement BLDC (brushless DC) drain pump motor Resolves "won't drain," "standing water," "unusual noise," and "intermittent draining" symptoms Impeller mechanism pumps water out through the drain hose to prevent clogs Compatible with 120V and 230V systems Direct drop-in replacement matching the original mounting and connections Replaces AP5917178, 113121, 4000925, EAP9606350, PS9606350, ASM773863, PD00036475, and 045900194701 Compatible with Samsung dishwashers Aftermarket replacement built to OEM-equivalent quality standards Typical repair takes 30 to 60 minutes Product Specifications Part Number XPDD31-00016A OEM Part Number DD31-00016A Part Type Dishwasher Drain Pump Motor (BLDC) Condition Aftermarket Replacement Brand Samsung Motor Type Brushless DC (BLDC) Voltage Compatibility 120V / 230V Weight Approx. 0.50 lbs Package Dimensions 4.02" x 3.50" x 3.54" Repair Difficulty Moderate — 30 to 60 minutes Quantity 1 drain pump motor Compatible Brand Samsung Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — This Step Needs Two Hands Turn off and unplug the dishwasher for safety, and shut off the water supply before beginning. Wear work gloves. Remove any panels or components blocking access to the motor pump. Disconnect all wiring from the old motor. Removing the old motor requires holding a release tab open while simultaneously twisting the motor counterclockwise — this two-handed step trips up a lot of first-time installers, so take it slowly and make sure the tab stays held open through the full twist. Once free, remove the old motor. Install the new DD31-00016A securely in the same mounting position. Reconnect all wiring according to the original connections. Reinstall any panels or components removed for access. Restore the water supply and power, then run a test cycle to confirm the dishwasher drains completely with no leaks or unusual noise. Tools needed: screwdriver, work gloves. Frequently Asked Questions My dishwasher isn't draining. Is this the part I need? Yes, this is the most direct symptom of a failed drain pump motor. Since this motor is what removes water from the tub during the drain phase, a worn or failed motor can leave standing water behind or prevent the cycle from completing properly. My dishwasher's drainage problem only happens sometimes. Could this still be the motor? Yes, this is possible. One customer replaced this exact motor to address an intermittent draining issue, noting it was somewhat of a guess since the problem didn't occur every cycle. Intermittent symptoms can still point to a motor that's beginning to fail rather than one that's failed completely, though it's worth noting the customer wasn't fully certain the replacement resolved their specific issue. What's the trickiest part of installing this motor? Removing the old motor requires holding a release tab open while twisting the motor counterclockwise at the same time — a two-handed maneuver that one customer specifically called out as the biggest challenge of the whole repair. Taking it slowly and keeping steady pressure on the tab through the full twist makes this easier. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the motor design, impeller mechanism, and voltage compatibility of the original DD31-00016A drain pump motor used in compatible Samsung dishwashers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

279827 Genuine OEM Whirlpool Dryer Drive Motor The 279827 is a Genuine OEM Whirlpool replacement dryer drive motor with pre-attached pulley, compatible with a wide range of Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Estate, and Kenmore dryers. The drive motor is the component that powers everything that moves in your dryer — it turns the drum belt (which rotates the drum to tumble clothes) and simultaneously drives the blower wheel (which pushes heated air through the drum and out the exhaust vent). When the motor fails, the dryer either won't start, won't tumble, stops mid-cycle, or makes loud humming, buzzing, or grinding noises. This is a dual-shaft motor: the drive shaft (1-3/4" long) connects to the drum belt via the pre-attached pulley, and the blower shaft (1-3/4" long) drives the blower wheel. The pulley is pre-attached and is not available separately — if your old motor's pulley is worn, this replacement includes a new one. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the 279827 is one of the most widely used dryer motors across the Whirlpool platform, replacing over 70 legacy part numbers spanning decades of production. Key cross-references include W10448892, W10396029, W10194250, 8066206, 3395654, 3398046, 3391888, 3395652, AP3094245, PS334304, and EAP334304. Includes the motor assembly, two 1/8" insulated female terminals, and instructions. Before replacing the motor, check the thermal fuse (electric dryers) and door switch first — a blown fuse or failed switch produces identical no-start symptoms and is a far cheaper fix. Installs in 45–90 minutes with basic hand tools. Quick Answer The 279827 Genuine OEM Whirlpool Dryer Drive Motor fixes Whirlpool, Maytag, KitchenAid, Amana, Roper, Estate, and Kenmore dryers that won't start, won't tumble, stop mid-cycle, or make loud humming/buzzing/grinding noises. Dual-shaft drive motor with pre-attached pulley. Shaft lengths: blower 1-3/4", drive 1-3/4". Includes motor assembly + 2 insulated female terminals + instructions. Genuine OEM. Key cross-refs: W10448892, W10396029, W10194250, 8066206, 3395654, AP3094245, PS334304. Before replacing the motor: check the thermal fuse and door switch first — they're far cheaper fixes for no-start symptoms. Common Problems This Part Fixes Dryer won't start — motor has failed or seized Dryer won't tumble — motor not powering the drum belt Dryer stops mid-cycle — motor overheating or intermittently failing Loud humming or buzzing when the start button is pressed — motor trying to start but can't Grinding or squealing noise during operation — worn motor bearings Motor runs but drum doesn't turn — pulley worn or belt slipping on a worn motor shaft Dryer runs intermittently — motor cutting out from thermal overload Burning smell from the motor area — overheating windings or seized bearings Motor locked up or seized — bearings failed completely Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer drive motor directly replaces a large number of OEM and cross-reference part numbers spanning decades of Whirlpool-platform dryer production. Key replacements include: 279827, 3388235, 2019, 2584, 26000299992, 26000695925, 337099, 337100, 3388209, 3388234, 339088, 3391886, 3391887, 3392857, 339627, 339635, 339662, 339672, 340907, 343029, 345437, 348804, 349587, 349808, 3980069, 660199, 660617, 661654, 687499, 687988, 690094, 690870, 694051, 695089, 695925, 697075, 786067, 786090, 8066206, 8066207, 8115, 8528319, 8538262, 8539555, S87-531, W10194250, W10366770, W10396029, W10396032, W10448892, AH334304, AM211, EA334304, K35-099, OEM9282744, AP3094245, AWP39205, EAP334304, PD00002349, PS334304. This is one of the most extensively cross-referenced parts in the Whirlpool catalog. If your old motor shows a part number not listed here, contact our support team with your dryer model number and we will verify compatibility. Compatibility This drive motor is compatible with select dryers from the following brands: Whirlpool dryers — electric and gas models across many generations (WED, WGD, LER, LGR, LEQ, LGQ series and many more) Maytag dryers — select Whirlpool-built models (MED, MGD, MEDC, MEDX series) KitchenAid dryers (select models) Jenn-Air dryers (select models) Amana dryers — select models (NED, NGD series) Magic Chef dryers (select models) Admiral dryers (select models) Norge dryers (select models) Roper dryers (select models) Estate dryers (select models) Kenmore / Sears dryers — select Whirlpool-built models (110-series) Important — Before Replacing the Motor: A dryer that won't start can be caused by several components that are far cheaper and easier to replace than the motor. Before ordering, check the thermal fuse (electric dryers — test for continuity with a multimeter), the door switch (test for continuity when pressed), and the start switch. All three produce identical no-start symptoms. Only replace the motor after ruling out these common causes — a motor replacement is a significant repair, and it's far cheaper to replace a $10 thermal fuse than a $150+ motor. Always verify your dryer model number before ordering. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Dryer drive motor — powers the drum (via belt and pulley) and the blower wheel simultaneously Dual-shaft design: drive shaft 1-3/4" and blower shaft 1-3/4" Pre-attached pulley (pulley is not available separately — included with the motor) Resolves "won't start," "won't tumble," "stops mid-cycle," "humming/buzzing," "grinding," and "burning smell" symptoms when caused by motor failure Includes motor assembly, two 1/8" insulated female terminals, and instructions One of the most widely used dryer motors across the Whirlpool platform — replaces 60+ legacy part numbers Key cross-references: W10448892, W10396029, W10194250, 8066206, 3395654, 3398046, 3391888, AP3094245, PS334304, EAP334304 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Estate, and Kenmore dryers Designed for heavy daily use with minimal noise DIY repair — installs in 45–90 minutes with basic hand tools Product Specifications Part Number 279827 Part Type Dryer Drive Motor with Pulley Condition Genuine OEM Application Dryers — Electric & Gas (Whirlpool platform) Drive Shaft Length 1-3/4" Blower Shaft Length 1-3/4" Pulley Pre-attached (not sold separately) Function Powers drum rotation (via belt/pulley) and blower wheel Kit Includes Motor assembly, 2x 1/8" insulated female terminals, instructions Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Estate, Kenmore Installation Notes ⚠️ Disconnect Power Before Starting — 240V Circuit (Electric) or Gas Line (Gas) — Wear Work Gloves Disconnect power at the breaker before beginning — electric dryers operate on a 240V circuit and there is a serious risk of electrical shock. For gas dryers, also shut off the gas supply at the shutoff valve. Wear work gloves and safety glasses. Pull the dryer away from the wall. Remove the lint screen and the screws beneath it. For most Whirlpool-platform dryers, remove the top panel by releasing the spring clips at the front, then detach the front panel by removing the screws at the top corners. Disconnect the door switch wires and set the front panel aside. Support the drum and slide it forward to access the motor at the bottom rear. Remove the drum belt from the motor pulley and idler pulley. Photograph the motor's wiring connections before disconnecting. Disconnect the electrical connections from the motor. Remove the blower wheel from the old motor's blower shaft — this typically requires a clamp or clip removal (the blower wheel threads off counterclockwise on many models). Remove the motor mounting clip/bracket and lift out the old motor. Install the new 279827 motor in the same position. Transfer the blower wheel onto the new motor's blower shaft and secure it. Reinstall the motor mounting clip/bracket. Reconnect the electrical connections using the included insulated female terminals if needed (match your photos). Re-route the drum belt around the drum, through the idler pulley, and onto the motor pulley. Reassemble the front panel, top panel, and lint screen. Restore power (and gas for gas dryers) and run a test cycle — confirm the drum spins smoothly and heated air flows through the drum. Tools needed: Phillips screwdriver, nut driver, socket/ratchet set, putty knife (for spring clips), needle-nose pliers, work gloves, safety glasses. Frequently Asked Questions My dryer won't start — is the motor definitely the problem? Not necessarily — and this is important because a motor replacement is a significant repair. A dryer that won't start can be caused by several components that are far cheaper and easier to replace. Before ordering the motor, check these first: 1) Thermal fuse (electric dryers) — a blown thermal fuse is the single most common cause of a no-start condition. Test for continuity with a multimeter; if it reads open, replace the fuse (~$10). 2) Door switch — test for continuity when pressed; if it's failed, the dryer won't start as a safety measure. 3) Start switch — if pressing the start button produces no response at all, the start switch itself may have failed. Only replace the motor after ruling these out. Signs that point specifically to the motor: a loud humming or buzzing when you press start (motor trying but can't turn), grinding or squealing from the motor area, or a motor that runs intermittently and cuts out. Why does the motor hum but the drum doesn't turn? A humming motor that won't turn is a classic sign of a seized or failing motor — the windings are energized (hence the hum) but the shaft can't rotate because the bearings have failed or the motor is mechanically stuck. This can also be caused by the blower wheel being jammed with lint or debris, preventing the shaft from turning — so before condemning the motor, check the blower wheel for obstructions. If the blower wheel spins freely and the motor still hums without turning, the motor has failed and needs replacement. Note: a humming motor that won't start will eventually trip the thermal fuse as a safety measure, so you may need to replace both the motor and the thermal fuse. Why are there so many cross-reference part numbers for this motor? The 279827 is one of the most extensively cross-referenced parts in the Whirlpool catalog because it's been the standard dryer drive motor across the Whirlpool platform for decades — spanning Whirlpool, Maytag, KitchenAid, Amana, Roper, Estate, Kenmore, and many other brands that Whirlpool manufactures for. Over the years, the motor has been assigned different part numbers by different brands, distributors, and catalog systems (W10448892, W10396029, 8066206, 3395654, 3398046, etc.), but they all point to the same motor. If your old motor shows ANY of those numbers, the 279827 is the correct replacement. Does this motor come with the pulley? Yes — the pulley is pre-attached to the motor and is not available separately. The pulley is what the drum belt rides on, transferring the motor's rotation to the drum. If your old motor's pulley was worn or grooved (a common cause of belt slipping and squealing), the new 279827 includes a fresh pulley. You will need to transfer the blower wheel from your old motor to the new one — the blower wheel is not included. Should I replace the belt and idler pulley while changing the motor? It's strongly recommended. When you replace the motor, the dryer is already apart and both the drum belt and idler pulley are right there in your hands. All three components wear from the same friction and heat cycles, and installing a new motor with a worn belt or a seized idler pulley puts unnecessary stress on the new motor from day one. Many technicians replace the belt, idler pulley, and drum support rollers as standard maintenance whenever the dryer is opened for a motor replacement — the combined cost of these parts is modest compared to the labor of disassembling the dryer again later. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same drive motor with pulley installed in compatible Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Estate, and Kenmore dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WPW10348269 Genuine OEM Whirlpool Dishwasher Drain Pump Motor The WPW10348269 is a genuine Whirlpool OEM drain pump motor for Whirlpool, KitchenAid, Kenmore, Maytag, Amana, Crosley, Estate, Inglis, Jenn-Air, Magic Chef, and Roper dishwashers. This pump uses an electric motor to create suction, pulling wastewater out of the tub and expelling it through the drain hose at the end of each cycle. This is the dedicated drain pump, distinct from a circulation pump — such as our WPW10605057 listing — which handles spraying water through the spray arms during the wash itself rather than draining it afterward. Rated 120VAC, 60Hz, 45W, 0.7A, with a run time pattern of 5 minutes on, 30 minutes off. Ships as a complete pump motor with impeller and O-ring. If the impeller becomes damaged or the motor shorts out and stops draining, the pump body itself can crack over time, leading to leakage — replacing the pump before that happens is the more reliable fix. Symptoms of a failing drain pump include water not draining from the tub, unusual noise such as grinding during the drain phase, or visible leaks from underneath the unit. It directly replaces W10348269, W10084573, 661662, 8558995, 8565839, W10158351, WPW10348269VP, AP6020066, AWP49992, PD00004898, PS11753379 Quick Answer The WPW10348269 Genuine OEM Whirlpool Dishwasher Drain Pump Motor fixes Whirlpool, KitchenAid, Kenmore, Maytag, Amana, Crosley, Estate, Inglis, Jenn-Air, Magic Chef, and Roper dishwashers that aren't draining, are making grinding noise during the drain phase, or are leaking from underneath. 120VAC, 60Hz, 45W, 0.7A. Includes impeller and O-ring. Replaces W10348269, WPW10348269VP, W10084573, W10158351, 661662, 8558995, 8565839, 2813258, AP6020066, EAP11753379, PD00004898, PS11753379. This is the drain pump — a separate part from our WPW10605057 circulation pump listing, which handles spraying water rather than draining it. Common Problems This Part Fixes Dishwasher not draining — standing water left in the tub after a cycle Grinding noise coming from the drain pump area Water leaking from underneath the dishwasher Cycle stalling or failing to advance past the drain step Dishes not getting cleaned as a downstream effect of drainage problems Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers: WPW10348269, W10348269, W10084573, 661662, 8558995, 8565839, W10158351, WPW10348269VP, AP6020066, AWP49992, PD00004898, PS11753379 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Whirlpool dishwashers, and also fits select KitchenAid, Kenmore, Maytag, Amana, Crosley, Estate, Inglis, Jenn-Air, Magic Chef, and Roper dishwashers built on the Whirlpool platform. Note — drain pump, not circulation pump: This is the dedicated drain pump, which removes wastewater from the tub. It is a separate part from our WPW10605057 listing, which is the circulation pump and diverter motor responsible for spraying water through the spray arms during the wash itself. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which pump your dishwasher needs. Key Features Genuine Whirlpool OEM part — factory-specified motor and impeller design Pumps wastewater out of the tub through the drain hose Resolves "not draining," "grinding noise," and "leaking underneath" symptoms caused by pump failure Complete assembly — includes pump motor, impeller, and O-ring Rated 120VAC, 60Hz, 45W, 0.7A Run time: 5 minutes on, 30 minutes off Dimensions: approximately 3-1/2"L x 3"W x 3-1/2"H Direct drop-in replacement — matches the original mounting and hose connections Replaces W10348269, W10084573, 661662, 8558995, 8565839, W10158351, WPW10348269VP, AP6020066, AWP49992, PD00004898, PS11753379 Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WPW10348269 Part Type Dishwasher Drain Pump Motor (with Impeller and O-Ring) Condition Genuine OEM Brand Whirlpool Function Pumps wastewater out of the tub through the drain hose Voltage 120VAC Frequency 60 Hz Wattage 45 W Amperage 0.7 A Run Time 5 min ON / 30 min OFF Dimensions Approx. 3-1/2"L x 3"W x 3-1/2"H Color White / Gray / Black / Yellow Related Part WPW10605057 circulation pump & diverter motor (different function, sold separately) Repair Difficulty Beginner to Moderate Quantity 1 drain pump motor Compatible Brands Whirlpool, KitchenAid, Kenmore, Maytag, Amana, Crosley, Estate, Inglis, Jenn-Air, Magic Chef, Roper Installation Notes ⚠️ Unplug Dishwasher Before Starting — Removing The Unit Makes Access Easier Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. This repair can be done without pulling the dishwasher out from under the counter, but many technicians find it considerably easier to access the pump if you do pull the unit out first. Remove the lower rack and any components blocking access to the tub floor, then work from underneath the dishwasher to reach the drain pump. Test the old pump for continuity with a multimeter before removing it — if it shows no continuity, or if it's getting power but still won't run, that confirms the pump has failed. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the drain hose connection from the old pump, remove its mounting hardware, and pull it free. Install the new WPW10348269 in the same position, reconnect the drain hose connection securely, and reconnect the electrical connector fully. Reinstall any components removed for access and the lower rack. Restore power, run a test cycle, and check underneath for leaks while confirming the tub drains completely at the end. Tools needed: Phillips screwdriver, 5/16" nut driver, 5/8" wrench, flathead screwdriver, multimeter, work gloves. Frequently Asked Questions Do I need to pull the dishwasher out from under the counter for this repair? Not strictly — this pump can be replaced without fully removing the dishwasher. That said, several customers who've done this repair note that pulling the unit out first makes access considerably easier, since you're working from underneath the appliance either way. If you have the space to pull it out, it's worth doing to make the job smoother. How do I know if the pump has actually failed? Test the pump motor with a multimeter set to continuity before replacing it. If there's no continuity, or if the pump is receiving power but still won't run, that confirms the motor has failed and the pump should be replaced. This quick check avoids replacing a part that isn't actually the problem. My old pump was leaking. Why does that happen? If the impeller becomes damaged or the motor shorts out and stops running, the pump body itself can develop a crack over time, which leads to leakage. Rather than trying to repair a leaking pump, replacing the complete assembly resolves both the drainage failure and the leak at the same time. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original motor, impeller, and hose connection configuration of the drain pump originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

5304532557 Refrigerator Genuine Evaporator Motor Replaces Part Numbers: 5304532557, 242077707, AP7194947, PS16745551. Description: This Part is a Genuine OEM refrigerator evaporator fan motor compatible with specific Electrolux, Frigidaire refrigerator models. The fan motor is a vital component of your refrigerator. It is designed to maintain cold temperatures by circulating air through the fresh food compartments. By doing so, it ensures uniform cooling within the refrigerator. This helps to prevent warm spots that can lead to frost build-up.

Read more less

W11414076 Genuine OEM Whirlpool Dishwasher Circulation Pump Motor Assembly The W11414076 is a Genuine OEM Whirlpool replacement circulation pump and motor assembly compatible with a wide range of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea dishwashers. The circulation pump is the heart of the wash system — it pressurizes and delivers water to the spray arms, driving the jets that blast food and residue off your dishes throughout the wash and rinse cycles. When the circulation pump fails, cleaning performance collapses: dishes come out dirty or unrinsed, water pressure at the spray arms drops, and the machine may make loud droning or grinding noises. This is a complete circulation pump and motor assembly. Common causes of failure include worn motor bearings (which produce a continuous drone that gets louder over time), deteriorated impellers, and seal breakdowns. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W11414076 is the current production part that supersedes W11122133. It also replaces AP6980104, EAP12745416, PS12745416, 4958907, and OEM20940317. Note: this assembly does not include the drain pump — your existing drain pump transfers over to the new assembly during installation. Installs in 45–90 minutes with basic hand tools (the dishwasher must be pulled out and laid on its back to access the pump). Quick Answer The W11414076 Genuine OEM Whirlpool Dishwasher Circulation Pump Motor Assembly fixes Whirlpool, KitchenAid, Maytag, Jenn-Air, and Amana dishwashers where dishes come out dirty or unrinsed, water pressure at the spray arms is weak, water pools in the tub, or the motor makes a loud droning/grinding noise. Complete circulation pump + motor assembly. Genuine OEM. Current part superseding W11122133; also replaces AP6980104, EAP12745416, PS12745416, 4958907, OEM20940317. Before ordering: if the motor runs but water is weak, try cleaning the impeller filter screen first — see the FAQ. Common Problems This Part Fixes Dishes coming out dirty or unrinsed — circulation pump not delivering water to the spray arms Weak water pressure at the spray arms — impeller worn or motor failing Loud droning noise that gets louder over time — worn motor bearings Grinding or unusual noise during operation Water retention/pooling in the bottom of the tub Leaks from the pump housing — seal breakdown Motor humming but spray arms barely turning Reduced cleaning performance overall Motor not running at all — failed pump motor windings Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This circulation pump motor assembly directly replaces the following OEM and cross-reference part numbers: W11414076, W11122133, AP6980104, EAP12745416, PS12745416, 4958907, OEM20940321, AWP45352, PD00070783 W11414076 is the current OEM production part superseding W11122133. Contact our support team with your model number if you need confirmation before ordering. Compatibility This circulation pump motor assembly is compatible with select dishwashers from the following brands: Whirlpool dishwashers — select models (verify with your parts diagram) KitchenAid dishwashers — select models Maytag dishwashers — select models Jenn-Air dishwashers — select models Amana dishwashers — select models Magic Chef dishwashers — select models Admiral dishwashers — select models Norge dishwashers — select models Roper dishwashers — select models Kenmore / Sears dishwashers — select Whirlpool-built models Ikea dishwashers — select Whirlpool-built models This assembly may comprise several parts — refer to your specific parts diagram to verify included items. Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Circulation pump and motor assembly — pressurizes and delivers water to the spray arms for effective cleaning and rinsing Resolves "dirty dishes," "weak water pressure," "loud droning motor," "grinding noise," and "water pooling" symptoms when caused by pump failure Addresses the common failure modes: worn motor bearings, deteriorated impellers, and seal breakdowns Current OEM production part — directly supersedes W11122133 Also replaces AP6980104, EAP12745416, PS12745416, 4958907, and OEM20940317 Motor separates from the pump case with 3 Torx screws — some customers replace only the motor if the pump case is fine Drain pump is not included — your existing drain pump transfers to the new assembly Compatible with Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea dishwashers DIY repair — installs in 45–90 minutes with basic hand tools Product Specifications Part Number W11414076 Supersedes W11122133 Part Type Dishwasher Circulation Pump & Motor Assembly Condition Genuine OEM Application Dishwashers (Whirlpool platform) Function Delivers water to the spray arms for washing and rinsing Motor Attachment Separates from pump case with 3 Torx screws Drain Pump Not included — transfer your existing drain pump Location Bottom of dishwasher (access by laying unit on its back) Compatible Brands Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, Ikea Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Wear Work Gloves — Major Access Required Disconnect power at the breaker and shut off the water supply before beginning. Wear work gloves to protect your hands. This is a more involved repair because the circulation pump is on the bottom of the dishwasher. Throw the circuit breaker, remove the lower access panel, and open the electrical box to completely disconnect the electrical from the dishwasher. Disconnect the water supply line and the drain line. Remove the anchor screws securing the dishwasher to the counter, then pull the dishwasher out of the cabinet. Have a large towel ready — rotate the dishwasher and lay it on its back to access the pump on the bottom. Photograph everything before disconnecting. Disconnect all connections to the main circulation pump: the drain pump, the electrical connections, the leak-detection plate and circuit, and the water lines. Undo all clamps to the circulation pump. Remove the old circulation pump assembly. Transfer your existing drain pump to the new W11414076 assembly — it is not included. (If you're only replacing a noisy motor and the pump case is good, the motor separates from the case with 3 Torx screws and can be swapped on its own.) Install the new assembly, reconnect the drain pump, electrical connections, leak-detection plate, water lines, and all clamps, matching your photos. Stand the dishwasher back up, slide it into the cabinet, reconnect water/drain/electrical, and secure the anchor screws. Run a short test cycle and check for leaks. Note: use your dishwasher's onboard diagnostic function to confirm the pump was the issue — light/error codes vary by model, so check the quick guide that came with your specific dishwasher rather than relying on codes listed online for other models. Tools needed: Phillips screwdriver, Torx driver (T-set), nut driver, pliers, large towel, work gloves. Frequently Asked Questions The motor runs but water barely reaches the spray arms — do I definitely need a new pump? Maybe not — try this first, because it could save you the entire repair. On many KitchenAid/Whirlpool-platform dishwashers, there's a fine filter screen INSIDE the circulation pump on the impeller. This screen can clog with microplastics and fine food particles over time (sometimes after a surprisingly small number of wash cycles), which chokes off water flow even though the motor is running perfectly. The screen can look clean but still be blocked — a real-world test is to hold water in the mesh cup: if it holds water like a cup instead of draining freely, it's clogged. Cleaning it with a toothbrush restores full flow. To access it you do have to pull the pump (the same disassembly as replacing it, then 2 Torx screws to open the pump), so if you're already this far in, disassemble and inspect the screen BEFORE installing a new pump — you may find the old pump is perfectly good. Running a dishwasher-safe cleaning product through the machine first is also worth a try. My dishwasher motor is loud and getting louder — is that the pump? Yes, that's a classic sign of worn circulation pump motor bearings. The motor bearings wear out over time, and as they degrade they produce a continuous drone that steadily gets louder. Once the bearings have failed, the noise won't go away on its own and the motor should be replaced. On this assembly, the motor separates from the pump case with 3 Torx screws — some customers who only have a bearing/noise problem (and an otherwise good pump case) simply swap the motor and reuse the case. If you order the full assembly, you get both, and you can decide during the repair whether to swap just the motor or the whole thing. Does this come with the drain pump? No — the W11414076 is the circulation pump and motor assembly, and it does not include the drain pump. During installation, you'll transfer your existing drain pump from the old assembly to the new one (it detaches and reattaches). This is normal for this repair. If your drain pump is also failing (separate symptoms: won't drain, water left standing after the cycle), that's a different part you'd order separately. The circulation pump handles washing/spray pressure; the drain pump handles emptying the tub. What's the difference between W11414076 and W11122133? These are the same circulation pump assembly across production revisions. W11122133 was the earlier OEM part number, and W11414076 is the current production version that Whirlpool issued as its direct replacement. Both are physically and functionally interchangeable — if your dishwasher's parts diagram shows W11122133, the W11414076 is the correct current replacement, and this listing covers both. The cross-references AP6980104, PS12745416, and 4958907 are additional catalog identifiers for the same part. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same circulation pump and motor assembly installed in compatible Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, and Kenmore Whirlpool-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC31-00187A Washer Drain Pump Motor The XPARTCO DC31-00187A is an aftermarket replacement washer drain pump motor compatible with select Samsung front-load and top-load washers in the WA4, WA5, WF2, WF3, WF4, and WF5 series, as well as select Kenmore washers built on the Samsung platform. The drain pump motor drives the impeller that expels water from the washer tub during the drain phase of each wash cycle. When the motor fails, the washer will not drain, will leave standing water in the tub, stop mid-cycle, or display error codes 5C, SE, SC, 5E, or SUDS. This motor-only assembly includes the pump motor, impeller, and replacement O-ring. Rated 120V, 60Hz, 80W, 1.1A (CL.F), with a 30-minute on / 30-minute off duty cycle. Dimensions: 4-1/4"L x 3"W x 4-1/4"H in gray/white/black plastic, metal, and rubber housing. The DC31-00187A is the motor component that installs into the existing pump housing on compatible Samsung washers — the pump housing (DC97-20621C assembly) is reused from the old pump, making this a motor-only swap rather than a complete pump replacement. It directly replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 03DC3100187A, 4958525, AP6977256, EAP9605762, PD00056512, PS9605762, and PS1274262. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DC31-00187A Washer Drain Pump Motor fixes Samsung front-load and top-load washers displaying error codes 5C, SE, SC, 5E, or SUDS, not draining, leaving standing water, or making loud noise during the drain cycle. Motor-only assembly — includes motor, impeller, and O-ring; installs into existing pump housing. 120V/60Hz/80W/1.1A/CL.F. 30 min on/30 min off. 4-1/4"L x 3"W x 4-1/4"H. Replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 4958525, AP6977256, PS9605762. Compatible with Samsung WA4/WA5/WF2/WF3/WF4/WF5 series. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Error codes 5C, SE, SC, 5E, or SUDS displayed — drain fault detected Washer stopping mid-cycle due to a drain fault Loud humming during the drain phase — motor energized but impeller not turning Grinding or rattling during drain — damaged impeller or worn motor bearings Clothes excessively wet after a cycle — pump not fully removing water before spin Water draining very slowly — motor weakening below rated performance Replaces Part Numbers This drain pump motor directly replaces the following OEM and cross-reference part numbers: DC31-00187A, DC31-00178A, DC31-00178D, 03DC3100187A, ASM654116, EAP9605762, 4958525, AP6977256, PD00056512, PS12742622, PX3516-01. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Samsung front-load and top-load washers from the following series: Samsung top-load washers — WA4 series (WA40J3000AW, WA44A3205AW, WA45H7000AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45R6100AC and related models) Samsung top-load washers — WA5 series (WA50F9A6DSW, WA50M7450AW, WA50R5200AW, WA50R5400AV and related models) Samsung front-load washers — WF2 series (select models) Samsung front-load washers — WF3 series (select models) Samsung front-load washers — WF4 series (WF42H5000AW, WF42H5200AW, WF45M5500AW, WF45N5300AW, WF45R6100AC, WF45T6000AW, WF45A6400AV, WF45B6300AP and related models) Samsung front-load washers — WF5 series (select models) Kenmore / Sears washers (select Samsung-built models) Note: The DC31-00187A is the pump motor only — it installs into the existing pump housing (DC97-20621C assembly) which is retained from the old pump. The housing is not replaced. Check and clean the drain filter before replacing the pump motor — a clogged filter is a common cause of drain errors that doesn't require motor replacement. Key Features Pump motor only — includes motor, impeller, and O-ring; installs into the existing DC97-20621C pump housing retained from the old pump Drives the pump impeller to expel water from the washer tub during the drain cycle Resolves Samsung error codes 5C, SE, SC, 5E, and SUDS caused by drain pump motor failure Rated 120V, 60Hz, 80W, 1.1A (CL.F) — correct specifications for compatible Samsung washers Duty cycle: 30 minutes on / 30 minutes off Dimensions: 4-1/4"L x 3"W x 4-1/4"H Replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 4958525, AP6977256, PS9605762, and PS1274262 Compatible with Samsung WA4, WA5, WF2, WF3, WF4, WF5 series and Kenmore Samsung-built washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number XPDC31-00187A Also Covers DC31-00187D, DC31-00178A, DC31-00178D (variants) Part Type Washer Drain Pump Motor (Motor Only — reuses existing housing) Condition Aftermarket Replacement Application Samsung Front-Load and Top-Load Washers (WA4/WA5/WF2/WF3/WF4/WF5) Voltage 120V AC Frequency 60 Hz Wattage 80W Amperage 1.1A Duty Class CL.F Duty Cycle 30 minutes on / 30 minutes off Dimensions 4-1/4"L x 3"W x 4-1/4"H Color Gray / White / Black Material Plastic / Metal / Rubber Includes Pump motor, impeller, O-ring Error Codes Resolved 5C, SE, SC, 5E, SUDS Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves — there are sharp edges inside the washer cabinet. For front-load models: remove the lower front access panel to expose the pump housing and filter. Drain residual water via the filter drain hose (have a shallow pan ready). Disconnect the wire harness from the motor. On most Samsung front-load models, the motor assembly twists out of the pump housing by rotating counter-clockwise — do not force it. Remove the old motor, note the O-ring position, and install the new O-ring from this kit onto the new DC31-00187A motor. Insert the new motor into the housing and twist clockwise to lock. Reconnect the wire harness. Reinstall the lower panel, restore power and water, and run a drain/spin cycle to confirm drainage. For top-load models: access through the lower front panel or by tilting the washer on its side depending on model. Tools needed: Phillips screwdriver, pliers, shallow pan, towels, work gloves. Frequently Asked Questions What is the difference between DC31-00187A and DC97-20621C? The DC31-00187A is the drain pump motor — the electrical component that drives the impeller. The DC97-20621C is the complete drain pump assembly, which includes the motor plus the outer pump housing, hose connection ports, and mounting hardware. When you order the DC31-00187A, you replace only the motor and reuse the existing DC97-20621C pump housing. When you order the DC97-20621C, you replace the entire assembly including the housing. Both resolve the same drain fault — the DC31-00187A is the more targeted repair when the housing is in good condition. What error codes indicate a drain pump motor failure? Error codes 5C, SE, SC, 5E, and SUDS on compatible Samsung washers all indicate a drain fault — the washer was unable to drain within the expected time. Before replacing the motor, clean the drain filter/coin trap at the lower front panel. A clogged filter is one of the most common causes of these error codes and does not require motor replacement. If the filter is clear and the codes persist, or if the pump is making loud noise or is completely silent during the drain phase, the motor needs replacement. What is the difference between DC31-00187A and DC31-00178A? These are cross-references for the same or very similar Samsung drain pump motor used across different Samsung washer generations. The DC31-00178A was used on earlier Samsung models and the DC31-00187A is the current version. Both are commonly listed as interchangeable replacements for each other in Samsung washer drain pump repair. The DC31-00187D and DC31-00178D are also variants of the same motor from different production runs. Should I clean the filter before replacing the pump motor? Yes — always check and clean the drain filter first. On Samsung front-load washers, the filter is accessible behind the lower front kick panel, typically on the right side — remove the cap slowly and drain water into a shallow pan first. Lint, coins, debris, and hair are very common causes of Samsung drain error codes that are completely resolved by cleaning the filter without any parts replacement. If the filter is clear and the error codes persist, the pump motor is the next component to replace. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications and performance of the original DC31-00187A drain pump motor. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WB26X10038 Microwave Turntable Motor The XPARTCO WB26X10038 is an aftermarket replacement turntable motor compatible with a wide range of GE, Hotpoint, RCA, Kenmore/Sears, and Frigidaire microwaves. This small synchronous motor mounts beneath the microwave cavity floor and spins the glass turntable so food cooks and heats evenly under the magnetron. When the motor wears out or its internal gears strip, the turntable stops rotating, rotates unevenly, or starts making a grinding or clicking noise as it struggles to turn. It's built with a D-shaped 1/4" metal drive shaft and two 3/16" male spade terminals matching the original connector, so it swaps in as a direct plug-and-play replacement. It directly replaces WB26X10038, 769741, ST16F, SM16F, SSM-16H, 15QBP1017, AGE21998, AH237772, AP2024962, EA237772, OEM6074895, PD00001126, PS237772, 5304408980, 639447, AH471476, EA471476, OEM6453786, AFR80909, AP2151259, PS471476, DE31-10172A. Installs in 5–10 minutes with basic hand tools. Quick Answer The XPARTCO WB26X10038 Microwave Turntable Motor fixes GE, Hotpoint, RCA, Kenmore/Sears, and Frigidaire microwaves with a turntable that won't turn, turns unevenly, or grinds/clicks while trying to rotate. 21V AC, 50/60Hz, 2.5–3 RPM, 3.0W, D-shaped 1/4" metal shaft, two 3/16" male spade terminals. Replaces WB26X10038, 769741, ST16F, SM16F, SSM-16H, 15QBP1017, AGE21998, AH237772, AP2024962, EA237772, OEM6074895, PD00001126, PS237772, 5304408980, 639447, AH471476, EA471476, OEM6453786, AFR80909, AP2151259, PS471476, DE31-10172A. Classic symptom: microwave heats fine, but the glass tray sits still or turns only partway. Common Problems This Part Fixes Turntable doesn't rotate at all, even though the microwave heats normally Turntable turns partway then stalls or reverses Grinding, clicking, or straining noise coming from under the cavity floor Uneven cooking or hot/cold spots caused by the tray not rotating Turntable coupler or drive hub spins but the glass tray doesn't move Intermittent rotation that works sometimes and not others Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This turntable motor directly replaces the following OEM and cross-reference part numbers: WB26X10038, 769741, ST16F, SM16F, SSM-16H, 15QBP1017, MDPJ030AF, AGE21998, AH237772, AP2024962, EA237772, OEM6074895, PD00001126, PS237772, 5304408980, 639447, AH471476, EA471476, OEM6453786, AFR80909, AP2151259, PS471476, DE31-10172A, MDPJ030AF If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This turntable motor is compatible with a wide range of microwaves from the following brands: GE microwaves (JVM, DVM, EMO, and CGLMV series) Hotpoint microwaves (GE-built models) RCA microwaves (GE-built models) Kenmore and Sears microwaves (363- and 721-prefix model numbers) Frigidaire microwaves (select models sharing this motor design) Note: This motor spans both GE-built and Frigidaire microwave platforms — a cross-brand fitment worth confirming against your specific model number, since not every model on either platform uses this exact motor. Always verify your appliance model number before ordering. Contact our support team with your model number if you're unsure. Key Features Direct-fit replacement microwave turntable motor with D-shaped 1/4" metal drive shaft Resolves "won't rotate," "grinding noise," and "uneven cooking" symptoms caused by motor failure 21V AC, 50/60Hz synchronous motor rated for 2.5–3 RPM output 3.0W power draw matching original electrical specifications Two 3/16" male spade terminals for a secure plug-and-play connection CW/CCW rotation capable to match your original motor's turning direction Replaces WB26X10038, 769741, ST16F, SM16F, SSM-16H, 15QBP1017, AGE21998, AH237772, AP2024962, EA237772, OEM6074895, PD00001126, PS237772, 5304408980, 639447, AH471476, EA471476, OEM6453786, AFR80909, AP2151259, PS471476, DE31-10172AXP, and several additional cross-reference numbers Compatible with GE, Hotpoint, RCA, Kenmore/Sears, and Frigidaire microwaves Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPWB26X10038 OEM Part Number WB26X10038 Part Type Microwave Turntable Drive Motor Condition Aftermarket Replacement Voltage 21V AC Frequency 50/60 Hz Speed 2.5–3 RPM Power 3.0W Shaft Type D-shaped metal, 1/4" Diameter ~2 inches Terminals Two 3/16" male spade connectors Compatible Brands GE, Hotpoint, RCA, Kenmore, Sears, Frigidaire Installation Notes ⚠️ Unplug Microwave Before Starting Disconnect power at the outlet. For over-the-range or built-in units, most turntable motors are accessed from inside the cavity by removing the drive coupler and roller guide, then reaching the motor from underneath the cavity floor (may require removing the microwave from its mount or accessing from the bottom/rear panel, depending on model). Photograph the wiring before disconnecting. Unplug the two spade terminal connectors from the old motor. Remove the mounting screws holding the motor bracket in place and remove the old motor. Install the new WB26X10038 motor in the same position and secure the mounting screws. Reconnect the spade terminals, matching your photos (polarity typically doesn't matter on these motors, but match original wire colors when in doubt). Reinstall the drive coupler and roller guide, reassemble any panels, restore power, and test that the turntable rotates smoothly and consistently. Tools needed: Phillips screwdriver, nut driver. Frequently Asked Questions My microwave heats food fine, but the turntable doesn't spin — is this the part? Yes, this is the classic symptom of a failed turntable motor. The heating function (magnetron, high-voltage components) is a completely separate system from the turntable drive, so a microwave can heat normally while the turntable motor has failed. Before ordering, also check that the glass tray and roller guide are seated correctly, since a stuck tray can sometimes be mistaken for a motor failure. Will this fit both GE and Frigidaire microwaves? This motor design is shared across select GE-built and Frigidaire microwave models, but not every model on either platform uses it. Confirm fit using your microwave's exact model number before ordering rather than assuming by brand alone. Do I need to transfer the drive coupler from my old motor? The drive coupler (the plastic piece that connects the motor shaft to the turntable support) is typically a separate component that sits on top of the motor shaft rather than being permanently attached, so you'll generally reuse your existing coupler and roller guide with the new motor unless they're visibly worn or damaged. Why is my turntable turning slowly or grinding instead of stopping completely? This usually means the motor's internal gears are stripped or worn rather than the motor being fully dead — it's still trying to turn but can't do so smoothly. This is a sign the motor needs replacement even if it hasn't failed outright yet. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine Whirlpool OEM Whirlpool WPW10184813 Refrigerator Genuine OEM Ice Dispenser Motor Genuine OEM ice-dispenser door motor for select Whirlpool-built refrigerators. Product Overview The Whirlpool WPW10184813 Refrigerator Ice Dispenser Door Motor is a Genuine Whirlpool OEM replacement part. It opens and closes the ice chute door during dispenser operation so ice can pass through the chute and the door can reseal afterward. A failed motor can cause the dispenser door to remain stuck open or closed, prevent ice from dispensing correctly, or allow warm room air to enter the chute area. Quick Answer WPW10184813 is the Genuine Whirlpool OEM ice-dispenser door motor that replaces W10184813 and 2305262. Verify the complete refrigerator model number before purchase. Common Problems This Part May Fix Ice dispenser door will not open Ice chute door will not close Ice maker makes ice but ice will not dispense Chute door sticks or operates intermittently Warm air enters around the dispenser chute Frost or moisture develops around the dispenser opening Replaces and Cross-References WPW10184813, 1489085, 2305262, AP6016508, EAP11749796, W10184813, AWP49407, OEM18049533, PD00006398, PS11749796 Cross-reference numbers are provided for identification. Always verify compatibility by complete refrigerator model number. Compatibility Used on select Whirlpool-built refrigerators sold under Whirlpool, KitchenAid, JennAir, Maytag, and Kenmore brand names. Compatible model examples include: GI7FVCXWY00 KSCS25FTMS02 KSRS25FTSS01 KSCS23FVMS02 KSRS25RSBT01 KSCS25FVMS01 KSCS25FTSS00 GC3NHAXVA00 106.56702500 Important: This is only a partial model list. Confirm the complete model number from the refrigerator identification label before ordering. Key Features Genuine Whirlpool OEM part Operates the ice dispenser chute door Replaces W10184813 and 2305262 For select Whirlpool-built side-by-side and French-door refrigerators Helps restore proper dispenser-door opening and closing Product Specifications Manufacturer Part Number WPW10184813 Brand Whirlpool Part Type Refrigerator Ice Dispenser Door Motor Condition New Quality Genuine OEM Application Ice Dispenser Chute Door Package Quantity 1 Motor Installation Notes Disconnect refrigerator power before service. Remove the dispenser trim and front components according to the appliance service procedure. Photograph connector and mechanical linkage positions before disassembly. Inspect the chute door, hinge, spring, and linkage for binding or damage before replacing the motor. Transfer or reconnect the wiring and linkage exactly as originally installed. Reassemble all dispenser parts and verify the chute door opens and fully closes before returning the refrigerator to service. Diagnostic tip: A dispenser that will not release ice can also be caused by an actuator, dispenser switch, control board, auger motor, frozen chute, or mechanical obstruction. Diagnose the dispenser system before replacing parts. Frequently Asked Questions Is WPW10184813 a Genuine Whirlpool OEM part? Yes. WPW10184813 is a Genuine Whirlpool OEM ice-dispenser door motor. Does it replace W10184813? Yes. Whirlpool lists WPW10184813 as the replacement for W10184813 and 2305262. What does this motor do? It opens and closes the dispenser chute door so ice can pass through the chute and the opening can reseal after dispensing. Will it fit every Whirlpool refrigerator? No. Verify the complete refrigerator model number before ordering because dispenser designs vary by model and production revision. Shop With Confidence Genuine Whirlpool OEM replacement part. Verify your complete refrigerator model and original part number before ordering. Genuine OEMIce Dispenser MotorCompatibility SupportFast U.S. Shipping

Read more less

DD31-00016B Dishwasher Drain Pump Motor - Compatible with Samsung Dishwashers Product Description Restore your dishwasher’s performance with the DD31-00016B Dishwasher Drain Pump Motor. This genuine OEM replacement pump ensures efficient water drainage during wash and rinse cycles, preventing water pooling and error codes. Designed for Samsung dishwashers. Replaces part numbers: DD31-00016B, AP7244901, PS17504318, EAP17504318, PD00089738. Verify your model number or contact support for assistance. Key Features: ✅ Brand Compatibility: Fits select Samsung dishwasher models. 💧 Specifications: OEM drain pump motor, 120V, 60Hz, 3.5" x 3.5" x 2.5", with plastic impeller and electrical connector for reliable drainage. DD31-00016B Motor Bldc PUMP; BD15-3C, 2800-3400RPM, 230 💰 Cost-Effective: OEM performance at a competitive price. 🛠️ Easy Installation: Requires a screwdriver, pliers, work gloves; typically installed in 20–40 minutes. 🛡️ Reliable Fixes: Resolves water pooling, poor drainage, or 5E/SE error codes. Safety First: Unplug the dishwasher and turn off the water supply before installation to avoid shock or leaks. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your dishwasher running smoothly today! Add to cart now for a budget-friendly fix!

Read more less

WPW10605057 Genuine OEM Whirlpool Dishwasher Pump & Motor Assembly The WPW10605057 is a genuine Whirlpool OEM circulation pump and diverter motor assembly for Whirlpool, Kenmore, KitchenAid, Jenn-Air, Maytag, Amana, Magic Chef, Admiral, Norge, Roper, and Ikea dishwashers. This assembly pumps water up through the spray arms throughout the wash cycle, and the integrated diverter motor controls which spray arm receives that water at any given moment. This assembly includes the circulation pump and diverter motor only — it does not include the drain pump, which is a separate component on this platform. Over time, the pump motor's internal windings can wear out or fail electrically, or the diverter mechanism can stick or bind. A failing assembly typically shows up as a dishwasher that isn't washing dishes properly because water isn't circulating through the spray arms, or leaking from underneath the unit. Whirlpool's own guidance recommends checking the motor's resistance with a multimeter if water isn't circulating, to confirm the assembly before replacing it. It directly replaces AP6023350, WPW10482502, W10482502, W10605057, 3021439, 3023239, PS11756692, W10236194, W10534160N, W10300740, and W10500285. Quick Answer The WPW10605057 Genuine OEM Whirlpool Dishwasher Pump & Motor Assembly fixes Whirlpool, Kenmore, KitchenAid, Jenn-Air, Maytag, Amana, Magic Chef, Admiral, Norge, Roper, and Ikea dishwashers that aren't washing dishes properly because water isn't circulating, or that are leaking from underneath. Includes the circulation pump and diverter motor — not the drain pump. Replaces WPW10482502, W10482502, W10605057, 3023239, W10300740, W10500285, AP6023350, AWP51141, PD00026666, PS11756692. Check the motor's resistance with a multimeter before replacing to confirm this assembly is actually the cause. Common Problems This Part Fixes Dishes not getting clean because water isn't circulating through the spray arms Dishwasher leaking from underneath the unit Weak or absent water spray during the wash cycle Motor humming without spraying water normally Inconsistent washing results from cycle to cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher pump and motor assembly directly replaces the following OEM and cross-reference part numbers: WPW10605057, WPW10482502, W10482502, W10605057, 3023239, W10300740, W10500285, AP6023350, AWP51141, PD00026666, PS11756692. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This pump and motor assembly is compatible with select Whirlpool dishwashers, and also fits select Kenmore, KitchenAid, Jenn-Air, Maytag, Amana, Magic Chef, Admiral, Norge, Roper, and Ikea dishwashers built on the Whirlpool platform, including model numbers such as KDTE104ESS, WDT710PAHZ, KDFE104DSS, WDT780SAEM, and WDT710PAHB. Note — circulation pump only, not the drain pump: This assembly includes the circulation pump and diverter motor. The drain pump on this platform is a separate component and is not included with this assembly. If your dishwasher isn't draining rather than not washing properly, you likely need the drain pump instead. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which part your dishwasher needs. Key Features Genuine Whirlpool OEM part — factory-specified pump and diverter motor design Includes the circulation pump and diverter motor, which controls spray arm water flow Resolves "not washing properly," "water not circulating," and "leaking underneath" symptoms Factory Certified Part built to Whirlpool's engineering specifications Direct drop-in replacement — matches the original mounting and hose connections Replaces WPW10482502, W10482502, W10605057, 3023239, W10300740, W10500285, AP6023350, AWP51141, PD00026666, PS11756692 Compatible with Whirlpool, Kenmore, KitchenAid, Jenn-Air, Maytag, Amana, Magic Chef, Admiral, Norge, Roper, and Ikea dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance DIY-friendly repair, typically about 30 minutes Product Specifications Part Number WPW10605057 Part Type Dishwasher Circulation Pump & Diverter Motor Assembly Condition Genuine OEM Brand Whirlpool Function Circulates water through the spray arms; diverter motor controls spray arm flow Includes Drain Pump No — sold separately Repair Difficulty Moderate — approx. 30 minutes Quantity 1 pump and motor assembly Compatible Brands Whirlpool, Kenmore, KitchenAid, Jenn-Air, Maytag, Amana, Magic Chef, Admiral, Norge, Roper, Ikea Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Remove the lower dish rack, the impeller/spray arm, and the drain filter to access the interior floor of the tub. Working from underneath the dishwasher, release the drain hose from the pump using pliers, then hand-unscrew the drain pump and temperature sensor about a quarter-turn each, being careful to release the small clip holding the drain pump in place — leave both of these components in place, since they're not part of this replacement. Release the three levers that clamp the pump and motor assembly to the bottom of the dishwasher, positioned roughly at 0, 120, and 240 degrees around the assembly. Photograph the electrical connections before disconnecting anything, since keeping track of exactly how everything was wired makes reassembly straightforward. Pop the old assembly up and out through the bottom of the dishwasher. If your old assembly used a separate counterweight, transfer it to the new assembly. Install the new WPW10605057 assembly through the same opening, reconnect all electrical connections exactly as photographed, and re-engage the three clamping levers. Reconnect the drain pump, temperature sensor, and drain hose you set aside earlier. Reinstall the drain filter, spray arm/impeller, and lower rack. Restore water and power, then run a test cycle to confirm normal water circulation with no leaks underneath. Tools needed: multi-screwdriver, pliers, work gloves. Frequently Asked Questions My dishwasher isn't cleaning dishes well. How do I know if this is the right part? Whirlpool's own guidance recommends checking the pump motor's resistance with a multimeter first if water isn't circulating properly. If the motor tests outside its expected resistance range, or shows no continuity at all, that confirms this assembly has failed and needs replacing rather than a different component being at fault. Should I replace the drain pump at the same time? Not necessarily — this assembly doesn't include the drain pump, and if your dishwasher is washing normally but just not draining, the drain pump (a separate part) is the more likely cause rather than this circulation assembly. If both symptoms are present, it's worth checking both components, but they aren't sold together in this listing. Do I need to replace the counterweight or reuse the old one? If your dishwasher's original assembly used a separate counterweight component, transfer it from the old assembly to the new one during installation rather than assuming a new one is included. Check your specific model's parts diagram if you're not sure whether this applies to your dishwasher. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original pump design, diverter motor function, and mounting configuration of the circulation pump and motor assembly originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM WR60X46085 Refrigerator Condenser Motor Fan Blade The WR60X46085 is a genuine OEM condenser Motor fan blade assembly for GE, Hotpoint, and RCA refrigerators. The blade presses onto the condenser fan motor shaft and pulls air across the condenser coil and compressor, carrying heat away so the sealed system can cool properly. When a blade cracks, loses a vane, or works loose on the shaft, the fan becomes noisy or unbalanced, or stops moving air, and the compressor and condenser start running hot. This is a genuine OEM part from GE Appliances, not an aftermarket equivalent, so the blade matches the original factory fit and balance. Note that this is the blade only. The condenser fan motor is a separate part, so if the motor itself has failed, the blade alone will not fix the problem. Quick Answer The Genuine OEM WR60X46085 Condenser Motor Fan Blade fixes a GE, Hotpoint, or RCA refrigerator with a noisy, rattling, or vibrating condenser fan, or a fan that spins without moving air because the blade is cracked, damaged, or loose. Genuine OEM, replaces the earlier WR60X10207 and WR60X10088 blades. Classic symptom: rattling or buzzing from the bottom rear of the refrigerator, or a warm cabinet with a compressor that runs constantly. Common Problems This Part Fixes Rattling, buzzing, or vibrating noise from the condenser fan area Visibly cracked, chipped, or broken blade vanes Blade loose on the motor shaft or spinning without moving air Compressor running constantly or running hot from poor condenser airflow Refrigerator not cooling well because heat isn't being removed from the condenser coil Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This condenser fan blade replaces the following part numbers: WR60X46085, WR60X10207, WR60X10088, AGE1580527, AP8075891, EAP1022410, PD00097217, PS1022410 GE has superseded WR60X10088 with WR60X10207, and WR60X10207 with the current WR60X46085. If your parts diagram or old blade shows either earlier number, the WR60X46085 is the current genuine replacement. Compatibility This blade is listed for refrigerators from the following brands: GE refrigerators Hotpoint refrigerators RCA refrigerators Note: A full model list isn't shown here, so confirm fit by matching the number on your old blade or your refrigerator's parts diagram against the Replaces list above, or contact our support team with your model number and we'll verify before you order. This is the blade only. The condenser fan motor is sold separately. Key Features Genuine OEM GE condenser Motor fan blade assembly, not an aftermarket equivalent Current part number, superseding WR60X10207 and WR60X10088 Restores quiet, balanced airflow across the condenser coil Authorized by GE for refrigerator models using flammable refrigerant such as R600a Blade only. Motor not included Simple replacement, typically 15–30 minutes Product Specifications Part Number WR60X46085 OEM Part Number WR60X46085 Part Type Refrigerator Condenser Motor Fan Blade Condition Genuine OEM Manufacturer GE Appliances Supersedes WR60X10207, WR60X10088 Included Condenser Fan Blade Only Application GE, Hotpoint & RCA Refrigerators Installation Notes ⚠️ Unplug Power Before Installing Unplug the refrigerator before starting. Pull the unit out and remove the rear or lower access panel to reach the condenser fan, which sits near the compressor. Pull the old blade off the motor shaft, noting how far it sits on the shaft and which way it faces. Press the new blade on to the same position, making sure it spins freely without touching the shroud or motor. While the panel is off, vacuum dust from the condenser coil and fan area, since buildup is a common cause of overheating. Replace the panel, push the refrigerator back, and restore power. Frequently Asked Questions My refrigerator is making a rattling noise at the back — is this the part I need? It could be. A cracked, chipped, or loose condenser fan blade is a common source of rattling or vibration near the compressor. Inspect the blade for damage and check that it spins freely. If the blade looks fine but the fan won't turn, the condenser fan motor may be the problem instead. Does this include the motor? No. This is the fan blade only. The condenser fan motor is a separate part. My old blade is a WR60X10207 or WR60X10088. Will this work? Yes. WR60X46085 is the current GE part number that supersedes both earlier numbers. Is this a genuine GE part? Yes. This is a genuine OEM part from GE Appliances, not an aftermarket equivalent. Will this fit my refrigerator? It is listed for GE, Hotpoint, and RCA refrigerators. Match the number on your old blade or parts diagram against the Replaces list, or contact our support team with your model number and we'll confirm fit before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less