ERP W10167627 Dryer Thermal Cutoff
Replaces Part Numbers: WPW10167627, AP6016109, PS11749393, W10167627.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO 137032600 Dryer Thermal Fuse – Compatible with Frigidaire, Electrolux, and Kenmore Dryers
Product Description
Protect your dryer from overheating with the XPARTCO 137032600 Dryer Thermal Fuse. This high-quality aftermarket replacement acts as a safety device that shuts off power to the heating element if the dryer overheats. A blown fuse can cause the dryer to stop heating or fail to start. Replacing it with this reliable and affordable XPARTCO fuse ensures safe operation and restores your dryer’s performance.
Replaces Part Numbers
137032600, 137060800, 1483164, 7137032600, AH2349395, EA2349395, PD00000890, EAP2349395, AP4368739, PS2349395.
Compatibility
This replacement thermal fuse fits select Frigidaire, Electrolux, and Kenmore dryers.
Example compatible models include (but are not limited to): Frigidaire AEQ6000ES0, Electrolux EIED55HIW0, and Kenmore 417.88042700.
Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Designed to match OEM performance for Frigidaire and Electrolux dryers
🔥 Safety Protection – Prevents overheating by cutting off power to the heating element
💰 Cost-Effective Fix – Affordable alternative to expensive OEM replacements
🛠️ Easy Installation – Direct-fit design for simple DIY replacement
🛡️ Fixes Common Issues – Restores heat function and resolves dryer not starting or heating problems
📐 Product Specification
Part Number: 137032600
Component Type: Dryer Thermal Fuse
Material: Heat-resistant plastic and metal housing
Mounting: Direct-fit installation on heater housing
Operating Conditions: Designed for residential electric dryers
Compliance: Built to OEM-equivalent quality standards (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, nut driver
⚠️ Safety First: Always unplug the dryer before performing any repairs to prevent electrical shock.
Steps:
Disconnect power and move dryer away from the wall.
Remove the rear access panel to locate the thermal fuse.
Disconnect wires and remove screws securing the old fuse.
Install the new XPARTCO 137032600 fuse and reconnect wires.
Reattach the back panel, restore power, and test heating function.
⏱️ Time Required: 10–15 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
🧰 Trusted Appliance Parts Supplier
🔄 30-Day Return Policy
Protect your dryer and restore performance — Add to Cart Now for a reliable, budget-friendly replacement!
Genuine OEM Dryer Part
W11683629 Dryer Genuine OEM Thermistor
A manufacturer-approved temperature-sensing component designed to help the dryer control system regulate heat and drying performance.
Product Description
The W11683629 Dryer Genuine OEM Thermistor monitors air temperature inside the dryer and sends temperature information to the electronic control system. The control uses this signal to cycle the heat source and maintain the correct operating temperature during the drying cycle.
This is a Genuine OEM replacement part manufactured to the original equipment specifications for fit, electrical response, and dependable operation. Replacing a failed thermistor can help restore accurate temperature control, normal cycle times, and consistent drying results.
Quick Answer
W11683629 is a Genuine OEM dryer thermistor. It senses dryer air temperature and communicates with the control board so the appliance can regulate heating. Replace it when testing or diagnosis confirms an open, shorted, damaged, or inaccurate temperature sensor.
Common Problems This Part Fixes
Dryer overheats or runs hotter than normal
Clothes remain damp after a complete cycle
Drying cycles take too long
Heat cycles on and off incorrectly
Dryer stops before clothes are dry
Temperature-sensor or heating-related error codes
Replaces Part Number
The product title identifies the following part number:
W11683629, W11452857, AP7216892, AWP1400864, PS17216463.
No additional replacement or cross-reference number was included in the supplied product title.
Compatibility
Designed for select dryer models that specify Genuine OEM part number W11683629. Appliance parts can look similar while using different resistance ranges, connectors, mounting positions, or control logic.
Always verify the complete dryer model number and the required part number before ordering. The model-number label is commonly located around the door opening, on the cabinet frame, or on the rear identification plate.
Key Features
Genuine OEM manufacturer-approved component
Monitors dryer operating temperature
Sends temperature feedback to the control system
Helps regulate heating and cycle performance
Built to original fit and electrical specifications
Direct replacement when W11683629 is specified
Product Specifications
Part Number
W11683629
Part Type
Dryer Thermistor / Temperature Sensor
Condition
New
Quality
Genuine OEM
Application
Clothes Dryer
Primary Function
Measures air temperature for the dryer control system
Package Quantity
1 Thermistor
Troubleshooting Guide
Disconnect the dryer from electrical power before opening or servicing the cabinet.
Inspect the exhaust vent, lint path, and blower area. Restricted airflow can produce symptoms similar to a failed thermistor.
Inspect the thermistor body, terminals, connector, and wire harness for damage, corrosion, loose connections, or heat discoloration.
Disconnect the thermistor and test resistance with a multimeter. Compare the reading with the dryer service information for the measured temperature.
Warm or cool the sensor carefully. Resistance should change smoothly as temperature changes; an open circuit, short circuit, or unstable reading can indicate failure.
Check the heater circuit, thermal devices, moisture-sensing system, and control board when the thermistor tests within specification.
Safety: Do not bypass a thermistor or protective temperature device. Installation and diagnosis should be performed by a qualified person when you are not comfortable servicing electrical appliances.
When Should You Replace This Part?
The thermistor is open, shorted, or outside the specified resistance range
The sensor reading does not change correctly with temperature
The housing or connector is cracked, burned, or physically damaged
A service diagnostic identifies W11683629 as the failed component
Airflow and related heating components have been checked and the thermistor fails testing
Shop With Confidence
Purchase the correct Genuine OEM replacement part for dependable fit and performance. Verify your dryer model number before ordering, and contact our parts team when compatibility assistance is needed.
Genuine OEM Fast U.S. Shipping Compatibility Support Secure Checkout
279838 Genuine OEM Whirlpool Dryer Heating Element
The 279838 is a Genuine OEM Whirlpool replacement dryer heating element assembly compatible with a wide range of Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef electric dryers. The heating element is the primary heat source in an electric dryer — a nickel-chromium resistance coil wound around a series of ceramic insulators inside a steel housing. When electricity passes through the coil during the drying cycle, it generates the heat needed to evaporate moisture from clothes. When the element coil burns through at a weak point, the circuit is broken and the dryer produces no heat.
This Genuine OEM part is manufactured by Whirlpool to factory specifications and is rated at 5400W / 240V with two 5/16" male terminals. It includes the heating element coil with partial housing and ceramic insulators already mounted — the remaining outer housing from your old assembly is reused. Note: the heating element does not include the thermostat or thermal fuse — those are separate parts. It directly replaces WP279837, 279837, 279838A, 279838VP, 3398063, 3398064, 3403585, 8565582, W10724237, 2438, AP3094254, and several additional cross-reference numbers. Installs in 20–30 minutes with basic hand tools.
Quick Answer
The 279838 Genuine OEM Whirlpool Dryer Heating Element fixes electric dryers that produce no heat, heat weakly, or take much longer than usual to dry clothes. 5400W / 240V, nickel-chromium coil, two 5/16" male terminals. Includes element coil with partial housing — reuses remaining outer housing from old assembly. Thermostat and thermal fuse not included. Replaces WP279837, 3398064, 3403585, 8565582, W10724237, 2438, AP3094254. Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef electric dryers.
Common Problems This Part Fixes
Dryer produces no heat at all — heating element coil has burned through
Dryer takes much longer than normal to dry clothes
Dryer tumbles normally but generates no heat during the cycle
Visible break, burn spot, or separation in the heating coil inside the housing
No continuity across the heating element terminals when tested with a multimeter
Burning smell from the dryer — arcing at a weak spot in the coil
Dryer trips the circuit breaker when the heat cycle is selected — shorted element
Replaces Part Numbers
This heating element directly replaces the following OEM and cross-reference part numbers:
279838, 279837, WP279837, 2438, 279838A, 279838VP, 3398063, 3398064, 3403585, 8565582, 4531017, 4617547, 4675511, 5324919, 5329098, 5895597, W10724237, AH334313, AWP39215, EA334313, EAP334313, FIX334313, AP3094254, PD00002351, PS334313.
Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This heating element is compatible with select electric dryers only from the following brands:
Whirlpool electric dryers (WED, MEDC, MEDX, Duet, Cabrio series and more)
Kenmore / Sears electric dryers — 110 series and Whirlpool-built models
Maytag electric dryers (MEDC, MEDX, MED series)
Amana electric dryers (NED series)
KitchenAid electric dryers
Roper electric dryers
Crosley electric dryers
Estate electric dryers
Inglis electric dryers
Admiral electric dryers
Magic Chef electric dryers
Note: This is for electric dryers only. Gas dryers use a gas burner assembly and do not have an electric heating element. Always verify your dryer type and model number before ordering. When replacing the heating element, it is strongly recommended to also replace the high-limit thermostat and thermal cut-off fuse (279973 kit) — a failed element is almost always associated with an overheating event that also stresses the thermal components.
Key Features
Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance
Primary heat source for electric dryers — nickel-chromium resistance coil generates heat during every drying cycle
Rated 5400W / 240V — correct wattage for compatible Whirlpool-family electric dryers
Two 5/16" male terminals — matches the original terminal configuration for direct wire connection
Includes heating element coil with partial housing and ceramic insulators pre-installed
Reuses remaining outer housing from old assembly — partial housing replacement only
Thermostat and thermal fuse not included — order 279973 kit separately if those also need replacement
Replaces WP279837, 3398064, 3403585, 8565582, W10724237, 2438, and over 15 additional cross-reference numbers
Compatible with 11 major appliance brands on the Whirlpool platform
DIY repair — installs in 20–30 minutes with basic hand tools
Product Specifications
Part Number
279838
Part Type
Dryer Heating Element Assembly (Electric)
Condition
Genuine OEM
Application
Electric Dryers Only
Wattage
5400W
Voltage
240V AC
Coil Material
Nickel-chromium resistance wire
Terminals
Two 5/16" male terminals
Includes
Element coil with partial housing and ceramic insulators — reuses remaining outer housing
Does Not Include
Thermostat, thermal fuse — order 279973 kit separately
Often Replaced With
279973 High-Limit Thermostat and Thermal Cut-Off Kit
Compatible Brands
Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef
Installation Notes
⚠️ Unplug Dryer Before Starting — Electric Dryers Only Disconnect power before beginning. Remove the back panel of the dryer by unscrewing the perimeter screws to access the heating element housing at the lower rear of the dryer. Photograph the wiring connections before disconnecting anything. Remove the two wire connections from the element terminals and the thermostat/thermal fuse wire connections from the housing. Unscrew the heating element housing from the dryer cabinet and slide the old assembly out. Remove the inner element frame from the outer housing — the outer housing is reused. Transfer the new 279838 element (which comes with a partial housing) into the existing outer housing. Reinstall the housing into the dryer, reconnect all wiring in the same positions as photographed, reinstall the back panel, restore power, and run a test heat cycle. Tip: while the element housing is removed, inspect the thermal fuse (3392519) and high-limit thermostat/cut-off kit (279973) and replace if needed. Tools needed: Phillips screwdriver, 1/4" nut driver.
Frequently Asked Questions
How do I test if the heating element has failed?
Unplug the dryer and remove the back panel to access the heating element housing. Disconnect the two wire terminals from the element and set your multimeter to continuity or resistance mode. Probe both terminals. A working heating element will show a resistance reading — typically between 8 and 15 ohms for a 5400W/240V element. An open circuit (no continuity / infinite resistance) confirms the element coil has burned through at a break point. You can also visually inspect the coil inside the housing for a visible gap, burn spot, or sag in the wire — any break in the coil indicates a failed element.
Does this element include the thermostat and thermal fuse?
No — the 279838 includes the heating element coil and partial housing only. The high-limit thermostat and thermal cut-off fuse are separate parts that mount on the element housing and are not included. When replacing the heating element, it is strongly recommended to also replace these thermal components using the 279973 thermostat kit, as a burned-out element is almost always the result of an overheating condition that also stresses the thermostat and thermal cut-off. Replacing them together ensures the heating system is fully restored and reduces the chance of a repeat failure.
Why does the 279838 only come with partial housing?
The 279838 heating element is designed as a replacement for the inner coil and frame assembly only — it installs inside the existing outer housing from your old assembly. The outer housing is a steel shell that does not wear out and does not need to be replaced under normal circumstances. By including only the partial housing (inner frame and coil), Whirlpool reduces part cost and simplifies installation — you simply swap the new element into your existing outer housing rather than replacing the entire assembly.
Will replacing the heating element fix my dryer if the thermal fuse is also blown?
Not by itself. If the thermal fuse (3392519) has also blown — which is common when the heating element fails — replacing only the element will not restore heat because the blown fuse permanently interrupts the circuit. You will need to replace both the heating element and the thermal fuse to restore normal operation. Since a thermal fuse blows due to overheating, also replacing the high-limit thermostat and thermal cut-off kit (279973) at the same time is recommended to ensure complete thermal protection is in place.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element assembly installed in compatible Whirlpool, Kenmore, Maytag, and related brand electric dryers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO DC47-00019A Dryer Heating Element Replaces WP35001247
The XPARTCO DC47-00019A is an aftermarket replacement universal-fit dryer heating element compatible with a wide range of electric dryers across multiple manufacturers — including Samsung, Whirlpool, Maytag, Amana, Inglis, and Kenmore. The heating element generates the heat that warms the air circulating through the dryer drum, evaporating moisture from wet clothes during each drying cycle. When the element fails, the dryer continues to tumble normally but produces no heat, leaving clothes damp at the end of a complete cycle.
This replacement element comes pre-assembled with insulators and restring already attached, allowing for fast installation. Rated 240V, 5300W, with metal and ceramic construction. Overall dimensions are approximately 17"L x 6-1/2"W x 2-1/2"H. Important: this is a heating element assembly only — you must reuse the housing/cannister from your old element when installing the new one. It directly replaces DC47-00019A, 35001247, WP35001247, WP35001247VP, TJDC47-00019A, DE0019A, ERDC47-00019A, 35001119, 2068550, 1185561, AP4045884, AP4201899, AP6008695, AH2038533, EA2038533, EAP2038533, EAP11741835, PD00001991, PD00002996, PS2038533, PS4205218, and PS11741835. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The XPARTCO DC47-00019A Dryer Heating Element fixes Samsung, Whirlpool, Maytag, Amana, Inglis, and Kenmore electric dryers that tumble normally but produce no heat or take much longer than usual to dry. Universal-fit element — 240V, 5300W. 17"L x 6-1/2"W x 2-1/2"H. Insulators and restring pre-attached. Must reuse the housing/cannister from the old element. Replaces DC47-00019A, 35001247, WP35001247, WP35001247VP, TJDC47-00019A, DE0019A, ERDC47-00019A, 35001119, 2068550, 1185561, AP4045884, AP4201899, AP6008695, PS2038533, PS4205218, PS11741835.
Common Problems This Part Fixes
Dryer tumbles normally but produces no heat — element coil burned through
Dryer takes significantly longer than usual to dry a load
Clothes coming out damp or only partially dried at the end of a cycle
Visible breakage in the element coil — snapped or burned-through Ni-Cr wire
Dryer trips the circuit breaker when the heat setting is selected — shorted element
Burning smell during operation — element arcing at a weak point in the coil
Multimeter continuity test on the element shows an open circuit
Replaces Part Numbers
This dryer heating element directly replaces the following OEM and cross-reference part numbers across multiple brands:
DC47-00019A, 2068550, AP4201899, ASM33630, AP2038533, DE0019A, ERDC47-00019A, PD00001991, PS4205218, TJDC47-00019A, WP35001247, 35001247, 1185561, AP6008695, AWP47390, EAP11741835, PD00002996, PS11741835, WP35001247VP.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This universal-fit heating element is compatible with select electric dryers from multiple manufacturers:
Samsung electric dryers — DV2, DV3, DV4, DV5, DVE series (DV40J3000EW, DV42H5000EW, DV42H5200EW, DV42H5600EP, DV45H7000EW, DV48H7400EW, DV50F9A7EVW, DV50F9A7EVP, DVE50M7450W, DVE50R5200W, DVE50R5400V, DV203AEW, DV206LEW, DV209AEW, DV210AEW, DV419AEU, DV448AEE, DV448AEP, DV5471AEW and many related models)
Whirlpool electric dryers (select models — see WP35001247 cross-reference)
Maytag electric dryers (MDE6700AYW, MDE6700AZW, MDG6700AWM, MDG6700AWW and related)
Amana electric dryers (NED7200TW10, YIED7200TW10 and related)
Inglis electric dryers (select models)
Kenmore / Sears electric dryers (Samsung and Whirlpool-built — select models)
Important — Reuse Existing Housing: This listing is for the heating element assembly only — the metal housing/cannister that the element sits inside is not included. You must reuse the housing from your old element. Remove the old element from its housing, then install the new DC47-00019A element into that same housing before reinstalling in the dryer. Also: this part is for electric dryers only — gas dryer models use different components. Always verify your specific model number before ordering.
Key Features
Universal-fit replacement heating element for multiple dryer manufacturers — replaces both Samsung DC47-00019A and Whirlpool/Maytag WP35001247 part numbers
Generates the heat that warms drying air — essential for the dryer to actually dry clothes
Pre-strung Ni-Cr (nickel-chromium) heating wire — high heat conductivity and resistance to warping over time
Insulators and restring already attached — ready for installation into the existing housing
Rated 240V, 5300W — correct electrical specifications for compatible electric dryers
Dimensions: 17"L x 6-1/2"W x 2-1/2"H
Metal and ceramic construction — durable for repeated heat/cool cycles
Electric dryers only — NOT compatible with gas dryer models
Important: heating element assembly only — must reuse the housing/cannister from the old element
Replaces 22+ OEM and cross-reference part numbers across Samsung, Whirlpool, Maytag, Amana, and related brands
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY repair — installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
XPDC47-00019A
Also Replaces (Whirlpool-side)
WP35001247, 35001247
Part Type
Dryer Heating Element Assembly (Universal Fit)
Condition
Aftermarket Replacement
Application
Electric Dryers Only (NOT gas)
Voltage
240V AC
Wattage
5300W
Terminal Connections
2 spade terminals
Dimensions
17"L x 6-1/2"W x 2-1/2"H
Material
Metal / Ceramic / Ni-Cr coil wire
Includes
Heating element assembly with insulators and restring pre-attached (housing NOT included — reuse old)
Compatible Brands
Samsung, Whirlpool, Maytag, Amana, Inglis, Kenmore
Installation Notes
⚠️ Unplug Dryer Before Starting — Do Not Touch the Element with Bare Hands Disconnect power before beginning. Wear work gloves throughout — there are sharp sheet metal edges inside the dryer cabinet. The new heating element coil is sensitive to skin oils, which can cause premature burnout — handle the element only by the metal frame, not the coil wire. Remove the rear panel of the dryer to access the heating element housing/cannister. Take a photo of all wire connections and the orientation of the element before disconnecting anything. Disconnect the wires from the old element terminals and remove the housing from the dryer. With the housing on a workbench, remove the old element from inside the housing — note exactly how it sits and how the restring is positioned. Install the new DC47-00019A element into the same housing, following the same orientation as the old element. Do not let the Ni-Cr heating wire touch the housing during installation — this can cause arcing and immediate burnout. Reinstall the housing in the dryer, reconnect all wires snugly to the correct terminals, and reinstall the rear panel. Restore power and run a test heat cycle to confirm the dryer is heating properly. While the rear panel is open, inspect the high-limit thermostat, thermal fuse, and thermistor — if the element failed due to overheating, these may also be stressed. Tools needed: Phillips screwdriver, 1/4" nut driver, work gloves.
Frequently Asked Questions
Does this really fit both Samsung AND Whirlpool dryers?
Yes — this is one of the more unusual cases in dryer parts where an aftermarket heating element has been designed to serve as a direct replacement for both the Samsung DC47-00019A and the Whirlpool/Maytag WP35001247 (35001247) elements. The two OEM elements share the same physical dimensions, electrical specifications (240V, 5300W), and terminal configuration, allowing a single aftermarket element to function correctly in both platforms. Compatible models span Samsung's DV series, Whirlpool/Maytag's affected dryers (MDE6700/MDG6700 and similar), and select Amana, Inglis, and Kenmore Whirlpool-built or Samsung-built models. Always verify your specific model number before ordering.
Why do I need to reuse the housing from the old element?
This listing is for the heating element assembly only — the metal cannister or housing that contains the element is not included. The housing is a heavy gauge metal enclosure with mounting brackets that secure it to the dryer cabinet, along with airflow ducting that directs air across the heating coil. Reusing the housing keeps the cost down and is standard practice for this type of replacement. Carefully remove the old element from the housing, install the new element in its place, and then reinstall the housing in the dryer. If your housing is damaged or burned through, it will need to be replaced separately.
How do I know if the heating element has failed?
The clearest sign is a dryer that tumbles and runs through a complete cycle normally but produces little or no heat, leaving clothes damp at the end. You may also notice the dryer taking much longer than usual to dry a load as it tries to compensate. Visually inspecting the element after removing the rear panel can reveal burn marks, breaks in the coil, or visible arcing damage. A multimeter continuity test on the disconnected element will also confirm failure — a working element shows continuity, while a failed element reads an open circuit (no continuity).
Should I replace the thermal fuse and thermostats at the same time?
It's a good idea to inspect them. When a heating element fails — especially if it failed due to overheating rather than simple end-of-life wear — the paired thermal fuse, high-limit thermostat, and thermistor located in the same area can also be stressed by the heat event. Since the rear panel must already be open to replace the element, checking these components' continuity with a multimeter is a quick step that can prevent a repeat repair if any of them are also on the verge of failing.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung or Whirlpool OEM part, but is manufactured to match the electrical specifications (240V, 5300W), dimensions, and Ni-Cr coil construction of the original DC47-00019A and WP35001247 heating elements that it replaces.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 3392519 Dryer Thermal Fuse Replaces WP3392519
The XPARTCO 3392519 is an aftermarket replacement dryer thermal fuse compatible with select gas and electric dryers from Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, and Magic Chef. The thermal fuse is a critical one-time-use safety device mounted on the exhaust duct or blower wheel housing that monitors the dryer's operating temperature.
When the dryer overheats — typically due to a clogged exhaust vent or restricted airflow — the thermal fuse permanently opens the circuit and cuts power to the heating system to prevent a fire. Once blown, the thermal fuse cannot be reset and must be replaced. This part measures 2 inches long x 1/2 inch wide, features two 3/16-inch terminals, and opens at approximately 196°F (91°C). Important: always check and clear the exhaust vent when replacing this fuse, as restricted airflow is the most common cause of thermal fuse failure.
Quick Answer
The XPARTCO 3392519 Dryer Thermal Fuse fixes dryers that won't start, won't heat, or stop mid-cycle due to overheating. It is a one-time-use safety fuse that permanently opens at 196°F (91°C) to cut power and prevent fires. Compatible with select Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, and Magic Chef dryers. Replaces WP3392519 and many other part numbers.
Common Problems This Part Fixes
Dryer won't start at all
Dryer runs but produces no heat
Dryer stops mid-cycle and won't restart
Timer advances but drum does not heat
Dryer shuts off too soon before clothes are dry
No continuity detected across fuse terminals during testing
Replaces Part Numbers
This thermal fuse directly replaces the following OEM and cross-reference part numbers:
3392519, WP3392519, 3388651, WE4X857, G4AP0500, 6L4101, 6L4101091C, ET401, 3388651, 694511, 80005, AWP47582, PD00002311, EAP11741460, AP6008325, PS11741460
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This thermal fuse is compatible with select gas and electric dryers from the following brands:
Whirlpool dryers (including Duet and Cabrio series)
Kenmore / Sears dryers (including Elite series)
KitchenAid dryers
Maytag dryers (including Centennial and Neptune series)
Roper dryers
Estate dryers
Inglis dryers
Crosley dryers
Amana dryers
Admiral dryers
Magic Chef dryers
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
One-time-use safety device — permanently opens at 196°F (91°C) to cut power and prevent dryer fires
Mounts on the exhaust duct or blower wheel housing — easy access for DIY replacement
Aftermarket replacement built to OEM-equivalent quality standards
2-terminal design — direct drop-in replacement, no modification required
Broad compatibility across 11 major appliance brands
DIY-friendly repair — installs with basic hand tools in under 30 minutes
Budget-friendly safety fix — one of the most common and least expensive dryer repairs
Product Specifications
Part Number
3392519
Part Type
Dryer Thermal Fuse
Condition
Aftermarket Replacement
Application
Gas and Electric Dryers
Opening Temperature
196°F (91°C)
Length
2 inches
Width
1/2 inch
Terminal Size
3/16 inch (2 terminals)
Resettable
No — one-time use only, must be replaced when blown
Location on Dryer
Exhaust duct / blower wheel housing
Compatible Brands
Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, Magic Chef
Installation Notes
⚠️ Safety First — Unplug Dryer and Shut Off Gas Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. The thermal fuse is located on the exhaust duct or blower wheel housing — access it by removing the back or front panel depending on your dryer model. Disconnect the two wire terminals from the old fuse, remove the fuse from its bracket, install the new fuse in the same position, reconnect the terminals, and reassemble the panel. Tools needed: Phillips screwdriver, 1/4-inch nut driver, and a multimeter to confirm the new fuse has continuity. ⚠️ Important: Before completing the repair, always check and clear the exhaust vent of any lint buildup — a blocked vent is the most common cause of thermal fuse failure and will blow the new fuse if not corrected.
Frequently Asked Questions
Will the 3392519 fit my dryer?
This thermal fuse is compatible with select gas and electric dryers from Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, and Magic Chef. Use the model search above to verify your model, or contact our support team before ordering.
What does a dryer thermal fuse do?
The thermal fuse is a one-time-use safety device that monitors the temperature inside the dryer. When the dryer overheats — typically due to a clogged exhaust vent — the fuse permanently opens the circuit, cutting power to the heating system to prevent a fire. Once blown, it cannot be reset and must be replaced.
How do I know if my thermal fuse is blown?
Test the fuse with a multimeter set to continuity mode. Touch the probes to each of the two terminals. A working fuse will show continuity (beep or near-zero ohms). A blown fuse will show no continuity (open circuit). If there is no continuity, the fuse is blown and must be replaced.
Why did my thermal fuse blow?
The most common cause is restricted airflow due to a clogged or kinked exhaust vent, a plugged lint trap, or a damaged blower wheel. Always check and clear the exhaust vent before or after replacing the fuse — failing to do so will cause the new fuse to blow again.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is designed to deliver reliable overheat protection at a more affordable price point.
Shop With Confidence
Parts-O-Matic is a U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock parts for major appliance brands and ship quickly from our U.S. warehouse. Our team is available to help you verify compatibility before you buy.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
WE04X20685 Genuine OEM GE Dryer Thermistor
The WE04X20685 is a genuine GE OEM center outlet thermistor for GE dryers, and also fits select Hotpoint, RCA, and Kenmore models. This thermistor monitors exhaust air temperature and communicates real-time readings to the control board, letting it track how the dryer is operating throughout the cycle.
Importantly, this thermistor is not part of the heating circuit itself, so it's unlikely to be the cause of a dryer that won't heat or produces too much or too little heat. Instead, when this thermistor malfunctions, it typically affects cycle timing or triggers a fault code, since the control board is receiving inaccurate or missing temperature data from this specific sensor location rather than losing its ability to regulate the heating element. A healthy thermistor reads approximately 100K ohms at room temperature. Common failure causes include moisture exposure gradually degrading the electronics over time, or physical stress damaging the thin connecting wires. Before assuming this thermistor is the cause of any symptom, it's worth confirming your exhaust venting has good airflow and is free of obstructions. It directly replaces WE4M336, 4369857, 76J1HX0005, AP5985030, AGE25863, EAP11721518, EAP11721518, OEM17955099, PD00043358, PS11721518.
Quick Answer
The WE04X20685 Genuine OEM GE Dryer Thermistor fixes GE, Hotpoint, RCA, and Kenmore dryers with incorrect cycle timing or a fault code related to this sensor. Reads approximately 100K ohms at room temperature. Replaces WE4M336, 4369857, 76J1HX0005, AP5985030, AGE25863, EAP11721518, EAP11721518, OEM17955099, PD00043358, PS11721518. This thermistor is not part of the heating circuit — it's unlikely to be the cause of a no-heat or overheating problem, but can affect cycle timing or trigger a fault code if defective.
Common Problems This Part Fixes
Incorrect or inconsistent cycle timing
Fault code related to this thermistor or temperature sensing
Erratic cycle behavior not explained by a heating element or thermal fuse issue
Control board receiving inaccurate temperature data from this sensor location
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer thermistor directly replaces the following OEM and cross-reference part numbers:
WE04X20685, WE4M336, 4369857, 76J1HX0005, AP5985030, AGE25863, EAP11721518, EAP11721518, OEM17955099, PD00043358, PS11721518
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This thermistor is compatible with select GE dryers, and also fits select Hotpoint, RCA, and Kenmore dryers built on the GE platform.
Note: This is a center outlet thermistor and is not in the heating circuit — a different function from some other GE thermistors that do regulate heat output directly. Always verify your full model number before ordering, since GE uses different thermistor designs and resistance ratings across its dryer lineup. Contact our support team with your model number if you're unsure.
Key Features
Genuine GE OEM part — factory-specified resistance curve and mounting fit
Center outlet thermistor monitors exhaust air temperature and reports it to the control board
Not part of the heating circuit — affects cycle timing and fault codes rather than heat output
Reads approximately 100K ohms at room temperature
Direct drop-in replacement matching the original mounting and wiring
Replaces WE4M336, 4369857, 76J1HX0005, AP5985030, AGE25863, EAP11721518, EAP11721518, OEM17955099, PD00043358, PS11721518
Compatible with GE, Hotpoint, RCA, and Kenmore dryers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
WE04X20685
Part Type
Dryer Center Outlet Thermistor
Condition
Genuine OEM
Brand
GE
In Heating Circuit
No
Typical Resistance
Approx. 100K ohms at room temperature
Function
Monitors exhaust air temperature and reports to the control board
Repair Difficulty
Easy
Quantity
1 thermistor
Compatible Brands
GE, Hotpoint, RCA, Kenmore
Installation Notes
⚠️ Unplug Dryer Before Starting — Check Venting Before Assuming This Sensor Is At Fault Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Before replacing this thermistor, confirm that airflow at the home's outside vent hood is good and that the dryer's venting is free of obstructions, since this thermistor is not part of the heating circuit and won't cause a heating problem on its own. Remove the back panel of the dryer, typically secured with several screws, to access the thermistor's mounting location. Test the old thermistor with a multimeter for electrical continuity to confirm it's actually faulty before replacing it. Photograph the wiring before disconnecting anything. Disconnect the wire terminals from the old thermistor and remove it from its mounting position. Install the new WE04X20685 in the same position, reconnect the wire terminals, and reattach the back panel. Restore power and run a test cycle to confirm normal cycle timing with no fault codes. Tools needed: Phillips or nut driver (model-dependent), multimeter, work gloves.
Frequently Asked Questions
My dryer isn't heating. Is this thermistor the cause?
Unlikely. This is a center outlet thermistor and is specifically not part of the dryer's heating circuit, so a fault here is unlikely to explain a no-heat or overheating symptom. If your dryer isn't heating, check the thermal fuse, heating element, or high-limit thermostat first. This thermistor is more likely to be the cause if you're seeing incorrect cycle timing or a specific fault code instead.
What symptoms does this thermistor actually cause when it fails?
Since this sensor feeds temperature data to the control board without being in the heating circuit itself, a failure here typically shows up as incorrect cycle timing or a fault code related to this specific sensor, rather than affecting how hot or cold the dryer runs.
Should I check anything else before replacing this part?
Yes — confirm your dryer's exhaust venting has good airflow and no obstructions before assuming this thermistor is at fault, since venting issues can cause a range of symptoms that might otherwise be mistaken for a sensor problem. This is a quick check worth doing first.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original resistance curve and mounting configuration of the thermistor originally installed in your dryer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WP8544771 Dryer Genuine OEM Heating Element
The WP8544771 is a genuine Whirlpool OEM heating element assembly for Whirlpool, Maytag, Kenmore, Amana, Crosley, and Inglis electric dryers. This assembly includes the housing with the heating element coil and insulators attached, and is what generates the heat used to dry your clothes throughout the cycle.
Rated 5400 watts, 240 volts. Over time, the coil can burn through at a weak point, causing an open circuit and a complete loss of heat. According to Whirlpool's own guidance, if a dryer stops heating, the heating element may have failed, but it's not actually the most common cause — a blown thermal fuse is more frequently the culprit, so it's worth checking that first. Symptoms of a failed heating element include the dryer running a full cycle with no heat, insufficient heat, or drying times that have gradually gotten longer. It directly replaces 8544771, W10836011, WP8544771VP, 1180054, AP6013115, AWP48654, DE4771, EAP11746337, PAT NO 7154072, PD00002399, PS11746337. As a genuine OEM part, the WP8544771 is manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance.
Quick Answer
The WP8544771 Dryer Genuine OEM Heating Element fixes Whirlpool, Maytag, Kenmore, Amana, Crosley, and Inglis electric dryers with no heat, insufficient heat, or drying times that have gotten longer. 5400W, 240V. Replaces 8544771, W10836011, WP8544771VP, 1180054, AP6013115, AWP48654, DE4771, EAP11746337, PAT NO 7154072, PD00002399, PS11746337. Check the thermal fuse first — per Whirlpool's own guidance, a blown thermal fuse is a more common cause of no-heat than a failed heating element.
Common Problems This Part Fixes
Dryer runs a full cycle but produces no heat at all
Dryer produces some heat, but not enough to dry clothes properly
Drying times that have gradually gotten longer than they used to
Clothes coming out cold or barely warm at the end of a cycle
Visible break or burned-through section in the heating coil
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer heating element directly replaces the following OEM and cross-reference part numbers:
8544771, W10836011, WP8544771VP, 1180054, AP6013115, AWP48654, DE4771, EAP11746337, PAT NO 7154072, PD00002399, PS11746337
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This heating element is compatible with select Whirlpool electric dryers, and also fits select Maytag, Kenmore, Amana, Crosley, and Inglis dryers built on the Whirlpool platform, including model numbers such as:
WED75HEFW, WED72HEDW, WED70HEBW, WED7590FW, WED9750WL0, WED8540FW0, WED9200SQ0, WED9500TW2, WED8300SW0, WED86HEBW0, WED9151YW0
MED3500FW, MEDB880BW0, MED6000XW1
Kenmore 11087729700, 11087872602, 11068102310, 11087089601
Note: This element is commonly purchased alongside the 280148 thermal cut-off kit (8557403 high-limit thermostat and 8318314 thermal fuse), since these components attach to the heating element assembly and often warrant replacement at the same time. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Whirlpool OEM part — factory-specified coil design and housing
Includes housing, heating coil, and insulators
Resolves "no heat," "insufficient heat," and "drying takes too long" symptoms caused by a burned-through coil
Rated 5400W, 240V
Direct drop-in replacement — no modification required
Replaces 8544771, W10836011, WP8544771VP, 1180054, AP6013115, AWP48654, DE4771, EAP11746337, PAT NO 7154072, PD00002399, PS11746337
Compatible with Whirlpool, Maytag, Kenmore, Amana, Crosley, and Inglis electric dryers
Genuine OEM replacement — guaranteed fit, materials, and performance
Typically a 30 to 60 minute DIY repair
Product Specifications
Part Number
WP8544771
Part Type
Dryer Heating Element Assembly
Condition
Genuine OEM
Wattage
5400 W
Voltage
240V
Includes
Housing, heating coil, insulators
Dimensions
Approx. 14.1" x 6.3" x 2.3"
Related Part
280148 thermal cut-off kit (8557403 thermostat + 8318314 fuse, sold separately)
Repair Difficulty
Easy to Moderate — 30 to 60 minutes
Quantity
1 heating element assembly
Compatible Brands
Whirlpool, Maytag, Kenmore, Amana, Crosley, Inglis
Installation Notes
⚠️ Unplug Dryer Before Starting — A 1/4" Dowel Or Rod Helps Release The Rear Clip Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. On many models, the heating element assembly can be removed from the front after removing the bottom "toe" panel. There's also a clip at the back of the assembly where it connects to the warm air duct leading into the dryer drum — this clip can be released from the front using a piece of 1/4" dowel or rod, which saves you from having to remove the back cover separately. Photograph the wiring before disconnecting anything. Disconnect the wire terminals from the old element, release the rear clip, and pull the assembly free. Since the thermal fuse and high-limit thermostat typically attach directly to this heating element assembly, this is a good opportunity to inspect or replace them at the same time, even if they're still technically working, since they share the same duty cycle and stress. Install the new 8544771 in the same position, reconnect the wire terminals, and re-engage the rear clip. Reassemble the toe panel or back cover. Restore power and run a test cycle to confirm the dryer is heating normally. Tools needed: Phillips screwdriver, 1/4" nut driver, 1/4" dowel or rod, work gloves.
Frequently Asked Questions
My dryer isn't heating. Should I replace the heating element first?
Not necessarily as your first step. Per Whirlpool's own guidance, while a failed heating element can cause a no-heat symptom, it's not actually the most common cause — a blown thermal fuse is more frequently the reason a dryer stops heating. It's worth checking the thermal fuse first, since it's a simpler and less expensive part to test and replace.
Is there an easier way to release the rear clip without removing the back cover?
Yes. One customer found that the clip at the back of the heating element assembly, where it connects to the warm air duct, can be released from the front of the dryer using a piece of 1/4" dowel or rod, avoiding the need to remove the back cover separately. They only discovered this after already taking the back cover off, so it's worth trying this approach first.
Should I replace the thermal fuse and thermostat while I'm in there?
It's worth considering. Since the thermal cut-off fuse and high-limit thermostat typically attach directly to the heating element assembly, one customer chose to replace both at the same time as the element, even though they were still technically working, simply because they were already accessible during the same repair. Our 280148 kit bundles the matching 8557403 thermostat and 8318314 fuse for this exact purpose.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original coil design, wattage, and housing configuration of the heating element assembly originally installed in your dryer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WP661566 Dishwasher Genuine High Limit Thermostat
Replaces Part Number: WP661566, 661566, W10339474, 2887, 3369777, 3370783, 3371618, 4171694, WP661566VP, AP6010246, PS11743423.
Description: The High Limit Thermostat is a Genuine OEM part for specific Kenmore, Whirlpool dishwasher models. This safety feature is designed to prevent the dishwasher from overheating by shutting off the power if the internal temperature exceeds a certain limit. It acts as a safeguard against potential hazards, such as fires, and ensures the dishwasher operates within safe temperature ranges.
17438200000404 Genuine OEM Midea Dryer Temperature Sensor (Thermistor)
The 17438200000404 is a Genuine OEM Midea replacement dryer temperature sensor (thermistor) compatible with an extensive range of Midea, Criterion, and Insignia electric and gas dryers. This NTC (negative temperature coefficient) thermistor continuously monitors air temperature inside the dryer and sends resistance-based readings to the control board, which uses this data to regulate heating element cycling, prevent overheating, and maintain consistent drying temperatures throughout the cycle. As the thermistor heats up, its electrical resistance decreases in a predictable way, allowing the control board to calculate the exact temperature in real time.
When this sensor fails — whether shorted, open, or providing drifted/inaccurate readings — the dryer may overheat, may not heat at all, may dry clothes unevenly, may take much longer than normal to complete a cycle, or may trigger a not-heating fault on models with digital displays. As a Genuine OEM part manufactured by Midea to factory specifications, the 17438200000404 directly replaces WF-123X2060 (an alternate catalog cross-reference used by some suppliers, including for compatible Maytag-branded Midea-built units). Installs in 20–30 minutes with basic hand tools.
Quick Answer
The 17438200000404 Genuine OEM Midea Dryer Temperature Sensor (Thermistor) fixes Midea, Criterion, and Insignia dryers that are overheating, not heating, drying unevenly, or taking too long to dry. NTC thermistor — resistance drops as temperature rises; ~10,000–12,000 ohms at room temperature (70°F). Genuine OEM. Replaces WF-123X2060. Compatible with Midea MLE41N1AWW, MLE45N1AWW/BWW, MLE45N3BMG/BWW, MLE52N3AWW, MLE52S7AGS/AWW, MLG45N1AWW/BWW, MLG45N3BMG/BWW, MLG52S7AGS/AWW, Criterion CDE41N1AW/CDG41N1AW, and a wide range of Insignia models.
Common Problems This Part Fixes
Dryer overheating — thermistor not accurately reporting rising temperature to the control board
Dryer not heating at all — thermistor circuit open or shorted
Dryer drying clothes unevenly — inconsistent temperature regulation during the cycle
Dryer taking much longer than normal to complete a cycle
Not-heating fault code displayed on models with digital control panels
Multimeter test shows 0 ohms (shorted) or infinite resistance (open) instead of the expected NTC reading
Dryer cycling heat on and off erratically
Replaces Part Numbers
This temperature sensor directly replaces the following OEM and cross-reference part numbers:
17438200000404, WF-123X2060, AP7157538, PS18188581
Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This temperature sensor is compatible with an extensive range of Midea, Criterion, and Insignia dryers, including:
Midea electric dryers — MLE41N1AWW, MLE41N1AWWC, MLE45N1AWW, MLE45N1BWW, MLE45N1BWWC, MLE45N3BMG, MLE45N3BWW, MLE52N3AWW, MLE52S7AGS, MLE52S7AWW
Midea gas dryers — MLG45N1AWW, MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AGS, MLG52S7AWW
Midea — CLADE67W, MDD160A2301E1305, MDD160VG012F0110EUS13
Criterion — CDE41N1AW (electric), CDG41N1AW (gas)
Insignia electric dryers — NSDRE67WH8A, NSDRE67WH8AC, NSFDRE67WH8A, NSFDRE67WH8AC, NSFDRE77WH8B, NSFDRE77WH8BC, NSTDRE67W1, NSTDRE75W1
Insignia gas dryers — NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance
NTC (negative temperature coefficient) thermistor — resistance decreases predictably as temperature rises, allowing precise temperature monitoring
Sends real-time temperature data to the control board to regulate heating element cycling and prevent overheating
Approximately 10,000–12,000 ohms of resistance at room temperature (around 70°F) when functioning correctly
Compatible across both electric and gas Midea-platform dryers, including Criterion and Insignia house-brand models
Replaces WF-123X2060
Installs in 20–30 minutes with basic hand tools
Product Specifications
Part Number
17438200000404
Part Type
Dryer Temperature Sensor (NTC Thermistor)
Condition
Genuine OEM
Application
Electric and Gas Dryers (Midea platform)
Sensor Type
NTC (Negative Temperature Coefficient)
Resistance at Room Temp
Approximately 10,000 – 12,000 ohms (~70°F)
Location
Blower housing/exhaust duct or drum cavity, depending on model
Compatible Brands
Midea, Criterion, Insignia
Installation Notes
⚠️ Unplug Dryer Before Starting (Shut Off Gas First on Gas Models) Disconnect power before beginning (and shut off the gas supply first if you have a gas dryer model). Midea dryers typically have 2–3 temperature sensors: an exhaust thermistor on the blower housing or exhaust duct, a drum thermistor inside the drum cavity, and on heat pump models, an evaporator thermistor — confirm which sensor location matches your symptom and part diagram before starting. Access the sensors by removing the back panel on vented models, or the side/bottom panels on heat pump models. Photograph the connector position before disconnecting. Unplug the old sensor's connector and inspect it for corrosion or heat discoloration on the wires — discoloration indicates prior overheating in that area. Remove the mounting clip or screw securing the old sensor and pull it free. Install the new 17438200000404 sensor in the same position, reseat the connector firmly, and secure the mounting hardware. Reassemble the panel, restore power, and run a test heat cycle to confirm normal temperature regulation. Tools needed: Phillips screwdriver, multimeter (for testing).
Frequently Asked Questions
How do I test if the temperature sensor (thermistor) has failed?
Unplug the dryer, disconnect the sensor's connector, and set your multimeter to resistance mode. At room temperature (around 70°F), a working NTC thermistor should read approximately 10,000 to 12,000 ohms. If the sensor reads 0 ohms, it has shorted internally. If it reads infinite resistance (open circuit, often shown as "OL" on the multimeter), the sensor has failed open. Either reading confirms the sensor needs replacement. If you have multiple sensors testing bad at the same time, check the shared ground wire — a broken ground connection can cause all sensors on that circuit to read as open even if the individual sensors are fine.
My Midea dryer has more than one temperature sensor — how do I know which one to replace?
Midea dryers typically use 2–3 temperature sensors depending on the model: an exhaust thermistor mounted on the blower housing or exhaust duct, a drum thermistor inside the drum cavity, and — on heat pump/ventless models — an evaporator thermistor in the refrigerant circuit area. The 17438200000404 is used across this Midea/Criterion/Insignia platform, but confirming the exact mounting location for your specific symptom (e.g., overheating vs. uneven drying) and model number before ordering will help ensure you're replacing the correct sensor.
What is the difference between 17438200000404 and WF-123X2060?
These are the same temperature sensor. WF-123X2060 is an alternate catalog cross-reference number used by some parts suppliers for the identical Midea-manufactured thermistor — it appears in listings for compatible Maytag-branded Midea-built units as well as the standard Midea, Criterion, and Insignia models. If your dryer's parts diagram shows either number, the 17438200000404 is the correct part.
Does this sensor fit my Insignia or Criterion dryer?
Yes — Insignia (Best Buy) and Criterion (Sears/Kmart) are house brands whose dryers in this size and configuration are manufactured by Midea and use the same internal components, including this temperature sensor. Confirmed compatible models include Insignia NSDRE67WH8A, NSFDRE67WH8A, NSFDRE77WH8B, NSTDRE67W1, NSTDRE75W1 (electric) and NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1 (gas), as well as Criterion CDE41N1AW (electric) and CDG41N1AW (gas). Always verify your specific model number before ordering.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same NTC thermistor temperature sensor installed in compatible Midea, Criterion, and Insignia dryers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XP382 Dryer Gas Valve Solenoid for DC62-00201A
The XP382 is an aftermarket replacement gas valve solenoid coil kit for Samsung gas dryers, and also fits select Whirlpool, Sears, and Kenmore models using a compatible two-coil gas valve. This is a newer-style coil kit that fits most dryers using a two-coil gas valve design, and it works alongside the gas valve assembly (DC62-00201A) to regulate the precise amount of gas needed to properly combust and generate heat for drying clothes.
Over time, these solenoid coils can weaken or fail electrically, preventing the gas valve from opening correctly even when the igniter is functioning normally. Symptoms of a failing gas valve solenoid include the burner not igniting even though the igniter glows, weak or inconsistent heat, or the dryer running a full cycle with little to no heat.
Quick Answer
The XP382 Dryer Gas Valve Solenoid fixes Samsung, Whirlpool, Sears, and Kenmore gas dryers using a compatible two-coil gas valve, where the burner isn't igniting despite the igniter glowing, heat is weak or inconsistent, or the dryer runs without heating. Fits Samsung DC62-00201A gas valve assembly. This is a gas ignition component — always shut off the gas supply and let the dryer cool before working on it, and if you smell gas at any point, stop and call a professional.
Common Problems This Part Fixes
Burner not igniting even though the igniter glows normally
Weak or inconsistent heat
Dryer running a full cycle with little to no heat
Gas valve failing to open when the igniter calls for gas
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer gas valve solenoid directly replaces the following OEM and cross-reference part numbers:
Fits Samsung Dryer Gas Valve Coils Kit for DC62-00201A
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This gas valve solenoid is compatible with select Samsung gas dryers using the DC62-00201A gas valve assembly, and also fits select Whirlpool, Sears, and Kenmore gas dryers using a compatible two-coil gas valve design.
Note: This is a coil kit that works with the gas valve assembly, not a replacement for the full valve body itself. If your gas valve assembly needs full replacement rather than just the coils, you'll need the complete DC62-00201A assembly. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which part your dryer needs.
Key Features
Aftermarket replacement gas valve solenoid coil kit
Resolves "burner won't ignite," "weak heat," and "no heat" symptoms tied to gas valve solenoid failure
Newer-style coil kit fitting most two-coil gas valve designs
Direct drop-in replacement matching the original mounting and connection
Fits Samsung Dryer Gas Valve Coils Kit for DC62-00201A
Compatible with Samsung, Whirlpool, Sears, and Kenmore gas dryers using a compatible two-coil valve
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
XP382
OEM Part Number
DC62-00201A (compatible coil kit)
Part Type
Dryer Gas Valve Solenoid Coil Kit
Condition
Aftermarket Replacement
Coil Configuration
Two-coil
Application
Gas Dryers
Repair Difficulty
Moderate — gas appliance component
Quantity
1 solenoid coil kit
Compatible Brands
Samsung, Whirlpool, Sears, Kenmore
Installation Notes
⚠️ Shut Off Gas Supply And Unplug Dryer Before Starting This is a gas ignition component. Turn off the gas supply to the dryer at the shutoff valve and disconnect power at the outlet before beginning. Allow the dryer to cool fully if it has recently been in use. Wear work gloves. If you smell gas at any point during this repair, stop immediately, do not operate any switches, leave the area, and contact your gas utility or a qualified technician from a safe location. Access the gas valve assembly, typically located near the burner housing — consult your dryer's service documentation for the exact access point on your model. Locate the old solenoid coils and disconnect their wiring. Remove the mounting screws or clips securing the old coils to the valve body and pull them free. Install the new XP382 coils in the same position, reconnect the wiring fully, and secure the mounting hardware. Restore the gas supply and power, then test the burner to confirm it ignites reliably with consistent heat. If you are not fully comfortable working with gas line connections, have a qualified technician perform this repair instead.
Frequently Asked Questions
My igniter glows but the burner doesn't light. Is this the part I need?
Yes, this is a classic sign of a failed gas valve solenoid. The igniter can glow and reach ignition temperature normally, but if the solenoid coils that open the gas valve have failed electrically, no gas reaches the burner to actually ignite, leaving the dryer to run without heat.
Do I need the whole gas valve assembly, or just this coil kit?
If the valve body itself is intact and only the solenoid coils have failed, this coil kit is the more targeted and typically less expensive repair. If the valve body is cracked, stuck, or otherwise physically damaged, you'll need the complete DC62-00201A gas valve assembly instead.
Is it safe to replace this myself?
This repair involves working around your dryer's gas supply line, so take care to fully shut off the gas and let the appliance cool before starting. If you're not comfortable working around gas appliances, or if you smell gas at any point, stop and contact a qualified technician or your gas utility rather than continuing the repair yourself.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the coil configuration and connection type needed to work with the DC62-00201A gas valve assembly used in compatible Samsung, Whirlpool, Sears, and Kenmore gas dryers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 5303918214 Refrigerator Defrost Thermostat
The XPARTCO 5303918214 is an aftermarket replacement defrost thermostat kit for Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators — commonly used on side-by-side and French door models equipped with an ice maker. This thermostat monitors the temperature of the evaporator coils: when the coils drop below a set temperature, it allows power to reach the defrost heater so frost can be cleared; once the coils warm back up, it cuts power to the heater again, protecting the evaporator from being overheated during that process.
The most common reasons this thermostat gets replaced are a classic pair of symptoms: the freezer stays cold while the fresh food refrigerator section runs warm, or the refrigerator simply isn't defrosting on its normal cycle. Because this thermostat sits behind the rear access panel near the ice maker on many compatible models, replacing it typically involves removing the ice maker and the back panel to reach it — a more involved repair than a thermostat mounted in an easily accessible spot. It directly replaces AP2150145, 892545, AH469522, EA469522, PS469522, and 75303918214.
Quick Answer
The XPARTCO 5303918214 Refrigerator Defrost Thermostat fixes Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators where the freezer stays cold but the fresh food section runs warm, or the refrigerator isn't defrosting on its normal cycle. Replaces AP2150145, 892545, AH469522, EA469522, PS469522, 75303918214. This is a separate part from our 5303918202 defrost thermostat listing — the two fit different model groups and are not interchangeable. Installation on many compatible models requires removing the ice maker to access the thermostat.
Common Problems This Part Fixes
Freezer stays cold but the fresh food refrigerator section runs warm
Refrigerator not defrosting on its normal cycle
Excessive frost or ice buildup on the evaporator coils
Refrigerator or freezer not cooling properly overall
Water leaking inside the refrigerator from melting ice buildup
Refrigerator running constantly as ice-caked coils reduce cooling efficiency
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This refrigerator defrost thermostat directly replaces the following OEM and cross-reference part numbers:
5303918214, 75303918214, 892545, AH469522, EA469522, AP2150145, 240372703, 39TVE31, EAP469522, PS469522, AFR16819, PD00000354, L47-22F, SL8214, ER5303918214
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This defrost thermostat is compatible with select Frigidaire refrigerators, and also fits select Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators built on the same platform, including model numbers such as:
FGHS2631PF4A, FGHS2655PF5A
FGHC2331PFAA, FGHC2331PFCA
FFHS2611PFEA, FFHS2611LBRA, FFHS2611LWMA, FFHS2622MSYA
FFSS2614QS6A
Note — not the same as 5303918202: This is a separate thermostat from our 5303918202 listing. The two fit different model groups and are not interchangeable, so always verify your full model number rather than assuming based on similar part number prefixes. Contact our support team with your model number if you're unsure which thermostat fits your refrigerator.
Key Features
Aftermarket replacement defrost thermostat kit for Frigidaire-platform refrigerators with an ice maker
Monitors evaporator coil temperature and controls power to the defrost heater
Resolves "freezer cold, fridge warm," "not defrosting on schedule," and "icy evaporator coils" symptoms caused by thermostat failure
Ships with wiring diagram guidance for a correct connection
Direct drop-in replacement — mounts to the original housing location
Replaces AP2150145, 892545, AH469522, EA469522, PS469522, and 75303918214
Compatible with Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
5303918214
OEM Part Number
5303918214
Part Type
Refrigerator Defrost Thermostat Kit
Condition
Aftermarket Replacement
Function
Monitors evaporator coil temperature and controls power to the defrost heater
Typical Location
Rear access panel area, near the ice maker on many compatible models
Repair Difficulty
Moderate — ice maker removal typically required for access
Quantity
1 defrost thermostat kit
Compatible Brands
Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, Crosley
Installation Notes
⚠️ Unplug Refrigerator And Shut Off Water Supply Before Starting Unplug the refrigerator from the wall outlet and turn off the water supply to the refrigerator before beginning. Wear work gloves. If your model has an ice maker, remove it first using a screwdriver to gain clearance for the next steps. Remove the back panel with a screwdriver to expose the defrost thermostat. Take out the existing thermostat and disconnect its wiring, labeling or photographing each connection first. Install the new 5303918214 thermostat by connecting the wires according to the wiring diagram provided with the kit, then secure the thermostat to the main housing using the small mounting screws. Reinstall the back panel, plug the refrigerator back in, turn the water supply back on, and reinstall the ice maker. Test the refrigerator over the following day to confirm both compartments are cooling evenly and the defrost cycle is running normally. Tools needed: screwdriver, wire cutters/strippers, work gloves.
Frequently Asked Questions
Do I really need to remove the ice maker for this repair?
On many compatible models, yes — the thermostat sits behind the rear access panel in an area that the ice maker partially blocks, so removing it first gives you the clearance needed to reach the panel and the thermostat behind it. It's an extra step compared to some simpler defrost thermostat replacements, but it's a standard part of this particular repair.
My freezer is cold but the fridge is warm. Is this the thermostat?
Yes, this is the classic symptom of a failed defrost thermostat. When it fails, the defrost heater can't run correctly to clear frost from the evaporator coil, and the resulting ice buildup blocks the airflow that's supposed to carry cold air to the fresh food compartment. The freezer, sitting closer to the coil, often stays reasonably cold, while the fresh food side runs warm since it depends on that circulated air.
I replaced the thermostat but my freezer temperature is still fluctuating. What should I check next?
Replacing this thermostat resolves the issue for most customers, but if fluctuation continues, it's worth checking the other components in the same defrost circuit — the defrost timer and defrost heater — since a failure in either of those can produce similar temperature instability even with a good thermostat installed. It's also worth confirming the door seals are sealing properly, since a poor seal lets warm air in and can cause temperature swings unrelated to the defrost system.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire OEM part, but is manufactured to match the temperature threshold, mounting configuration, and function of the original 5303918214 defrost thermostat used in compatible Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
