DC97-19289F Genuine OEM Samsung Washer Drain Pump Assembly
The DC97-19289F is a Genuine OEM Samsung replacement washer drain pump assembly compatible with a wide range of Samsung top-load washers in the WA40, WA41, WA42, WA44, WA45, WA48, WA50, WA52, and WA54 series, as well as select Kenmore models built on the Samsung platform. The drain pump removes water from the washer tub during the drain portion of each wash cycle. When the pump fails, the washer will display error codes 5C, SE, nd, 5E, FO2, or E5, leave standing water in the tub, stop mid-cycle, or produce unusual noise during draining.
This complete drain pump assembly is rated 120V, 60Hz, 80W, 1.1A with a 30-minute on / 30-minute off duty cycle. It directly replaces DC97-19289A, DC97-19289B, DC97-17349B, DC97-17366A, DC97-17366J, and PX3516-01. Note: the wire plug on the new pump may differ slightly from the original — if the connector does not match your washer's harness, transfer the wiring harness from the old pump to the new one. Installs in 20–30 minutes with basic hand tools.
Quick Answer
The DC97-19289F Genuine OEM Samsung Washer Drain Pump Assembly fixes Samsung top-load washers displaying error codes 5C, SE, nd, 5E, FO2, or E5, not draining, leaving standing water, or making loud noise during the drain cycle. 120V/60Hz/80W/1.1A, 30 min on/30 min off duty cycle. Compatible with Samsung WA40 through WA54 series and Kenmore (Samsung-built). Replaces DC97-19289A, DC97-19289B, DC97-17349B, DC97-17366A, DC97-17366J, PX3516-01. Note: if wire plug differs, transfer harness from old pump.
Common Problems This Part Fixes
Error codes 5C, SE, nd, 5E, FO2, or E5 — washer cannot drain within the allotted time
Washer not draining — standing water remaining in the tub after a cycle
Washer stopping mid-cycle due to a drain fault
Loud humming, grinding, or rattling noise during the drain cycle
Water draining very slowly — worn pump motor below rated performance
Water leaking from the drain pump area at the bottom of the washer
Pump running continuously but water not being expelled from the tub
Replaces Part Numbers
This drain pump directly replaces the following OEM and cross-reference part numbers:
DC97-19289F, DC97-17349B, DC97-19289B,DC97-17366A, DC97-17366J, DC97-19289A,ASM772133, AP6806651, EAP12592631, PD00049911, PX3516-01, PS12592631.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain pump is compatible with select top-load washers from the following brands and series:
Samsung top-load washers — WA40 series (WA400PJHDWR and related models)
Samsung top-load washers — WA41 series (WA41A3000AW and related models)
Samsung top-load washers — WA42 series
Samsung top-load washers — WA44 series (WA44A3205AW and related models)
Samsung top-load washers — WA45 series (WA45H7000AW, WA45M7050AW, WA45N3050AW, WA45T3200AW and related models)
Samsung top-load washers — WA48 series (WA48H7400AW and related models)
Samsung top-load washers — WA50 series (WA50F9A7DSP, WA50M7450AW and related models)
Samsung top-load washers — WA52 series (WA52M7750AW, WA52M8650AW and related models)
Samsung top-load washers — WA54 series (WA54M8750AV and related models)
Samsung top-load washers — WA456DRHDSU series
Kenmore / Sears top-load washers (select Samsung-built models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Removes water from the tub during the drain and spin cycles for proper washer operation
Resolves Samsung error codes 5C, SE, nd, 5E, FO2, and E5 caused by drain pump failure
Rated 120V, 60Hz, 80W, 1.1A — correct electrical specifications for compatible Samsung top-load models
30-minute on / 30-minute off duty cycle — matches the operational requirements of compatible models
Replaces DC97-19289A, DC97-19289B, DC97-17349B, DC97-17366A, DC97-17366J, and PX3516-01
Wire plug may differ from original — transfer harness from old pump if connector does not match
Compatible with Samsung WA40 through WA54 series and Kenmore Samsung-built top-load washers
Genuine OEM part manufactured by Samsung to factory specifications — guaranteed fit and performance
DIY repair — installs in 20–30 minutes with basic hand tools
Product Specifications
Part Number
DC97-19289F
Also Replaces
DC97-19289A, DC97-19289B (prior versions)
Part Type
Washer Drain Pump Assembly
Condition
Genuine OEM
Application
Samsung Top-Load Washers
Voltage
120V AC
Frequency
60 Hz
Wattage
80W
Amperage
1.1A
Duty Cycle
30 minutes on / 30 minutes off
Error Codes Resolved
5C, SE, nd, 5E, FO2, E5
Connector Note
Wire plug may differ — transfer harness from old pump if needed
Compatible Brands
Samsung, Kenmore (Samsung-built)
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. Tilt the washer back or lay it on its side to access the drain pump at the bottom of the machine. Place towels and a shallow pan to catch residual water when the pump is disconnected. Note the wiring connector orientation before disconnecting — take a photo if needed. If the new pump's connector does not match the washer's harness, carefully transfer the wiring harness from the old pump to the new pump. Disconnect the drain hoses from the pump using pliers to loosen the clamps. Unscrew the pump mounting screws and remove the old pump. Install the new DC97-19289F pump in the same position, reconnect drain hoses and secure with clamps, and reconnect the wiring harness. Restore water supply and power, then run a drain cycle to verify proper drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan, towels.
Frequently Asked Questions
What error codes indicate a drain pump failure on Samsung washers?
Error codes 5C, SE, nd, 5E, FO2, and E5 on Samsung top-load washers all indicate a drain fault — the washer was unable to drain within the expected time. These codes can also be caused by a clogged drain filter, blocked hose, or kinked drain line, so check those first. If the filter and hose are clear and the error persists after clearing them, the drain pump is the most likely cause.
What is the difference between DC97-19289F, DC97-19289A, and DC97-19289B?
These are successive revisions of the same Samsung drain pump assembly. DC97-19289A was the original version, DC97-19289B was an update, and DC97-19289F is the current version. Samsung issues revised part numbers when minor production changes are made — all three perform the same function and the DC97-19289F is the correct current replacement for any of the earlier versions. The DC97-17349B, DC97-17366A, and DC97-17366J are additional older cross-references for this pump used on earlier Samsung top-load models.
Why might the wire plug on the new pump differ from the original?
Samsung revised the wiring connector on this drain pump across different production runs. If the DC97-19289F pump you receive has a different connector than your washer's harness, do not force the connection. Instead, carefully remove the wiring harness from the old pump and transfer it to the new pump — both versions use the same internal terminals and the harness swap is straightforward. This is a known and documented step for this part and does not affect performance or safety.
Should I check the drain filter before replacing the pump?
Yes — always check and clean the drain filter and inspect the drain hose for kinks or blockages before replacing the pump. A clogged filter or blocked hose can cause the same error codes as a failed pump and clearing the blockage may resolve the problem without needing a new part. On Samsung top-load washers the drain filter is typically located at the bottom front of the machine. If the filter and hose are clear and the error persists, the pump needs replacement.
Is this an OEM or aftermarket part?
This is a Genuine OEM part manufactured by Samsung to factory specifications. It is the exact same drain pump assembly installed in compatible Samsung and Kenmore top-load washers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
WH42X10650 Washer Control Panel, White
Replaces Part Numbers: WH42X10650, AP3995175, 1264621, AH1482468, EA1482468, PS1482468.
The WH42X10650 is a genuine GE replacement part, specifically designed as a control panel for GE washing machines. It houses and operates the control buttons and display, ensuring compatibility and reliability for your appliance.
WB24X25013 Genuine OEM GE Range Surface Burner Infinite Switch Replaces WB24X47186.
The WB24X25013 is a genuine GE OEM infinite control switch for a dual (bridge) surface element on GE, Hotpoint, and select Kenmore electric ranges — the kind of burner with an inner coil and an outer coil that can be run together for a large pot or as the inner coil alone for a small pan. Because it's governing two coil zones instead of one, this switch uses six terminal connections rather than the three or four found on a standard single-element infinite switch, and it mounts to the control panel with a distinctive figure-8 style shaft and two female mounting holes.
Like any infinite switch, it doesn't have fixed heat positions — instead it rapidly cycles power to the element(s) on and off at a ratio set by the knob, giving continuous heat adjustment from warm to high rather than a handful of steps. Rated for 240VAC at 15 amps. Over years of cycling, the internal contacts on a switch like this wear, pit, or weld together, and boilovers or spills can corrode the switch body and cause it to fail. A worn switch on a dual-element burner can produce an unusually wide symptom set: the whole burner may fail, or just the outer ring may stop responding while the inner coil still works, or the burner may stay on continuously regardless of the knob position. It directly replaces WB24X47186, 191D4774P005, AP5999509, PS11729102, EAP11729102, and 4464832. As a genuine OEM part, the WB24X25013 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance.
Quick Answer
The WB24X25013 Genuine OEM GE Range Surface Burner Infinite Switch fixes GE, Hotpoint, and Kenmore electric ranges with a dual (bridge) element burner where the burner won't turn on or off, only the outer ring fails to work while the inner coil still heats, the burner stays on continuously, or heat can't be adjusted. Six-terminal switch, figure-8 shaft, 240VAC / 15A. Replaces WB24X47186, 191D4774P005, AP5999509, PS11729102, EAP11729102, 4464832. Not the same switch as a standard single-element infinite switch — this one is specific to dual/bridge burners with an inner and outer coil.
Common Problems This Part Fixes
Dual-element burner won't turn on at all when the knob is turned
Outer ring of a dual/bridge element won't activate while the inner coil still works
Burner won't turn off — stays hot even with the knob at the off position
Burner stuck at one heat level regardless of where the knob is set
No ability to adjust temperature — always full blast or always low
Intermittent burner operation — works sometimes, not others
Knob feels loose, gritty, or doesn't turn smoothly through its range
Burner failure that followed a boilover or liquid spill on the control panel
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This range surface burner infinite switch directly replaces the following OEM and cross-reference part numbers:
WB24X25013, WB24X47186, 191D4774P005, AGE1543754, AP7216136, PS11729102, PS17872685, EAP11729102, 4464832, 191D4774P005, MDSA-W767-GEM
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This dual-element infinite switch is compatible with select GE, Hotpoint, and Kenmore electric ranges equipped with a dual (bridge) surface element, including model families such as:
GE JB6, JB7, and JB8 series electric ranges (including JB630, JB640, JB645, and JB655)
GE JBS series electric ranges
GE JS6 and JS7 series electric ranges (including the JS760 series)
GE GRS and GRF series electric ranges
Hotpoint electric ranges (select GE-built models)
Select Kenmore electric ranges built on the GE platform
Verified model numbers include: JB645RK6SS, JS760EP6ES, JS760DP6WW, JS760SP7SS, JS760DP7WW, JS760SP6SS, JS760FP7DS, JS760FP6DS, JS760EP7ES, JB860EJAES, JB860FJADS, and GRS500PV1SS.
Note: This is a six-terminal switch built specifically for a dual (bridge) element with a figure-8 style shaft and two female mounting holes — it is NOT interchangeable with a standard single-element infinite switch such as the WB24T10029 or WB24T10025, which use fewer terminals and a different shaft profile. Fitting a standard single-element switch to a dual-element burner circuit will not correctly control both coil zones. Always verify your full model number and confirm the affected burner is a dual/bridge element before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine GE OEM part — factory-specified contact design for dual-element switching
Six-terminal design controls both the inner coil and outer ring of a dual (bridge) surface element
Figure-8 style shaft with two female mounting holes matched to the original control panel bracket
Infinite switch design allows continuous heat adjustment rather than a handful of fixed positions
Rated 240VAC at 15 amps
Resolves "burner won't turn on," "outer ring not working," "won't turn off," and "stuck at one heat level" symptoms caused by worn or corroded switch contacts
Direct drop-in replacement — mounts to the same control panel bracket and wiring harness
Replaces 191D4774P005, AP5999509, PS11729102, EAP11729102, and 4464832
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
WB24X25013
Part Type
Range Surface Burner Infinite Switch (Dual/Bridge Element)
Condition
Genuine OEM
Brand
GE
Element Type Controlled
Dual (bridge) surface element — inner coil + outer ring
Terminal Connections
6
Shaft Style
Figure-8
Mounting
Two female mounting holes
Voltage
240VAC
Amperage
15A
Function
Cycles element power to allow continuous (infinite) heat adjustment across both coil zones
Quantity
1 switch
Compatible Brands
GE, Hotpoint, select Kenmore
Installation Notes
⚠️ 240V Circuit — Unplug Range Or Shut Off Breaker Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning — this switch operates on a 240V circuit, and working on it while powered presents a serious shock hazard. Wear work gloves. Remove the burner knob (it typically pulls straight off, though some models use a small retaining clip) then remove the screws securing the control panel or backsplash to reach the switch from behind. Photograph the wiring before disconnecting anything — this is a six-terminal switch, and getting even one wire out of place can miswire the inner coil, the outer ring, or both. Label each wire as you remove it. Disconnect all six terminal connections from the old switch, then remove the mounting screws from the two mounting holes and pull the switch free from its figure-8 shaft opening. Install the new WB24X25013 in the same orientation, reconnect each of the six wires exactly as labeled, and secure the mounting hardware. Reinstall the control panel or backsplash, press the knob back onto the shaft, restore power, and test the burner at every knob position — confirm the inner coil and outer ring both activate correctly (together and, if your model supports it, with the outer ring switched off independently) before considering the repair complete. Tools needed: Phillips screwdriver, nut driver, wire terminal pliers (helpful but optional), work gloves.
Frequently Asked Questions
How do I know if my burner uses a dual-element switch like this one?
Look at the burner element itself: a dual (bridge) element has two distinct coil rings — a smaller inner coil and a larger outer ring — usually with a separate control or a knob position that lets you activate just the inner coil for a small pan or both rings together for a large pot. A standard single-ring element has only one coil and uses a simpler switch with fewer terminals. If your range has this two-ring burner design, the WB24X25013 (or the exact switch behind it) is the correct type — but always confirm your model number, since dual-element switches vary by range generation.
Only the outer ring of my dual burner doesn't work. Is it the switch or the element?
It could be either, and it's worth narrowing down before ordering. If the inner coil heats normally but the outer ring never activates at any knob position, check the outer ring element itself first — a broken element coil is a common and cheaper fix than a switch. If the outer ring element tests fine but the switch's six-terminal wiring specific to the outer coil circuit has failed or corroded, the infinite switch is the correct replacement.
Can I use a standard single-element infinite switch instead if this one is out of stock?
No. A standard single-element switch has fewer terminals and cannot correctly control the two separate coil zones of a dual (bridge) burner. Wiring a single-element switch into a dual-element circuit will leave one coil zone permanently uncontrolled or non-functional. Always order the six-terminal dual-element switch specified for your model.
What does "infinite switch" mean?
An infinite switch lets you dial in a continuous range of heat rather than a few fixed positions, by rapidly cycling the element's power on and off at a ratio set by the knob — low settings get short power pulses, high settings get long ones. When the internal contacts wear or weld together from years of cycling, the switch can get stuck feeding constant power (burner always hot) or stop switching at all (burner always off), regardless of where the knob is turned.
A spill got into the control panel and now the burner won't turn off. Is that the switch?
Very likely, yes. Liquid boilovers and spills are one of the most common causes of infinite switch failure — moisture gets into the switch body, corrodes or bridges the internal contacts, and the switch can end up stuck feeding power continuously even with the knob turned to off. If you suspect this, shut off power to the range immediately at the breaker rather than relying on the knob, since a shorted switch may not respond to it at all.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original six-terminal wiring, figure-8 shaft, 240VAC/15A electrical rating, and dual-coil switching behavior of the infinite switch originally installed for the dual (bridge) element in your GE, Hotpoint, or Kenmore range.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WH12X10527 Washer Genuine OEM Timer
Replaces Part Numbers: WH12X10527, AP5645215, PS4704240.
Description: This washer timer is a Genuine OEM part for select GE washing machine models. This timer controls the various cycles of the washing machine, including wash, rinse, and spin cycles. By regulating the duration and sequence of each cycle, the timer ensures that the washing machine operates smoothly and efficiently.
AAN73209838 Genuine OEM LG Washer Drain Pump & Cabinet Base Assembly
The AAN73209838 is a genuine LG OEM combined drain pump and cabinet base assembly for LG washers. This assembly bundles the washer's drain pump — which pumps water out of the drum and through the drain hose at the end of each cycle — together with the cabinet base structure it's mounted to. Because these two components ship together as one assembly, replacing this part addresses both the drain pump function and the base structure it sits in at the same time.
Common causes of failure include a worn or jammed drain pump motor, or physical damage or corrosion to the cabinet base itself over years of use. A failing assembly typically shows up as the washer failing to drain, unusual noise during the drain phase, or water leaking from underneath the unit.
Quick Answer
The AAN73209838 Genuine OEM LG Washer Drain Pump & Cabinet Base Assembly fixes LG washers that won't drain, make unusual noise during the drain phase, or are leaking water from underneath the unit. Combined drain pump and cabinet base assembly. This is a larger, heavier assembly than a standalone drain pump — installation involves more disassembly than a simple pump swap.
Common Problems This Part Fixes
Washer not draining — standing water left in the tub after a cycle
Unusual noise during the drain phase of the cycle
Water leaking from underneath the washer
Cycle stalling or failing to advance past the drain step
Visible damage or corrosion to the cabinet base structure
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
AAN73209838, 4873470, 4985882, AHA75673401, AP6991753, AP6991765, EAP12580277, EAP16222263, FIX16222263, PS12580277, PS16222263, ALG51685, PD00091778
We were not able to confirm additional cross-reference or superseding part numbers for this specific part from reliable sources at the time this page was built, so none are listed here rather than guessed. If you have a cross-reference number for your appliance, contact our support team and we will verify compatibility before you order.
Compatibility
This drain pump and cabinet base assembly is compatible with select LG top-load washers, including model numbers such as WT7060CW, WT7100CW, WT7250CW, WT7300CV, T1780WFHT, and T1789EFH5T/T1789EFH5U/T1789EFHT/T1789EFHKD variants.
Note: This is a combined assembly, not a standalone drain pump — if your washer only needs the pump replaced and the cabinet base is intact, ask our support team whether a standalone pump option is available for your model before ordering this larger assembly. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine LG OEM part — factory-specified pump and base assembly
Combined drain pump and cabinet base assembly in a single part
Resolves "won't drain," "noisy drain phase," and "leaking underneath the washer" symptoms
Direct drop-in replacement — matches the original mounting and hose connections
Compatible with a range of LG top-load washer models
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
AAN73209838
Part Type
Washer Drain Pump & Cabinet Base Assembly
Condition
Genuine OEM
Brand
LG
Application
Top-Load Washers
Function
Pumps water from the drum through the drain hose; provides the cabinet base structure
Repair Difficulty
Moderate to Hard — larger assembly than a standalone pump
Quantity
1 combined assembly
Compatible Brand
LG
Installation Notes
⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Remove Standing Water First Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. If there's standing water left in the tub from the original failure, remove as much as possible by hand with a cup or towel before starting the repair. Because this is a combined pump and cabinet base assembly rather than a standalone pump, access typically requires tipping the washer back or removing more of the cabinet than a simple pump swap — check your model's service diagram for the exact disassembly sequence, since it varies by model. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the drain hose connections from the old assembly, remove the fasteners securing it to the washer frame, and carefully remove it, noting how the base supports the rest of the cabinet. Install the new AAN73209838 assembly in the same position, reconnect the drain hose connections securely, reconnect the electrical connector fully, and secure all mounting fasteners. Reassemble the cabinet in reverse order, restore the water supply and power, then run a cycle and check underneath for leaks while confirming the tub drains completely at the end. Tools needed: Phillips screwdriver, socket set, pliers, towels or a small cup for removing standing water, work gloves.
Frequently Asked Questions
Do I need this whole assembly, or is there a smaller drain pump option for my model?
Some LG washer models offer a standalone drain pump as a separate, smaller part, while others require this combined pump-and-base assembly because the two are integrated on that particular platform. Check with our support team using your model number to confirm whether a standalone pump is available for your washer before ordering this larger assembly, since it can save you time and cost if a smaller part fits your model.
Why is this repair more involved than a typical drain pump replacement?
Because this part includes the cabinet base structure along with the pump, accessing and replacing it typically involves more disassembly than swapping a standalone pump alone — you're not just disconnecting a pump, you're also working with part of the washer's supporting frame. Budget more time for this repair than you would for a simple pump-only replacement, and consider having a second person help support the cabinet during removal and installation.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original pump design, hose connections, and cabinet base mounting configuration of the assembly originally installed in your washer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WH23X28418 Washer Genuine GE OEM Drain Pump
The WH23X28418 is a Genuine GE OEM replacement drain pump and motor assembly compatible with select GE, Hotpoint, Haier, RCA, and Kenmore top-load and front-load washers. The drain pump removes water from the washer drum during the drain and spin cycles — expelling water and detergent through the drain hose so that clothing comes out clean and free of excess water. When the pump fails, the washer will not drain, may leave standing water in the tub, or may produce loud noises during the drain cycle.
This complete drain pump and motor assembly is rated at 120V, 60Hz, 1.25A with a duty cycle of 10 minutes on and 50 minutes off. It includes the pump and motor with harness — the harness and plug extend approximately 10 inches from the motor. The pump measures 5-1/4" L x 5-1/8" W x 5-1/2" H and includes a drain pump seal. It directly replaces WH23X24178 and WH23X27574, as well as several additional cross-reference numbers. Installs in 20–40 minutes with basic hand tools.
Quick Answer
The WH23X28418 Washer Genuine GE OEM Drain Pump fixes GE, Hotpoint, Haier, and RCA washers that won't drain, leave standing water in the tub, are noisy during draining, or leak around the pump area. Complete pump and motor with harness and drain pump seal. 120V/60Hz/1.25A. Dimensions 5-1/4" L x 5-1/8" W x 5-1/2" H; harness extends approx. 10". Replaces WH23X24178 and WH23X27574.
Common Problems This Part Fixes
Washer not draining — standing water remaining in the tub after a cycle
Washer stopping mid-cycle due to a drain fault or drain-related error code
Loud humming, grinding, or buzzing noise during the drain cycle
Washer pumps but will not spin — pump failure preventing cycle completion
Water leaking from around the drain pump area
Clothes not clean or coming out soaking wet due to incomplete drainage
Pump impeller jammed by debris causing motor burnout
Replaces Part Numbers
This drain pump directly replaces the following OEM and cross-reference part numbers:
WH23X24178, WH23X28418, WH23X27574, 290D1201G001, 290D1201G002, 290D1201G003, AGE26155, B40-3A01, B30-3A02, PD00055680, EAP12723115, AP6889136, PS12723115.
WH23X28418 is the current updated part number replacing the discontinued WH23X24178 and WH23X27574. If your washer documentation or old pump label shows either of those numbers, this is the correct replacement.
Compatibility
This drain pump is compatible with select washers from the following brands and series:
GE top-load washers — GTW220, GTW330, GTW335, GTW460, GTW465, GTW485, GTW490, GTW500, GTW680, GTW720, GTW725, GTW750 series and others
GE front-load washers — select GFW series models
Hotpoint top-load washers — HTW200, HTW240 series and others
Haier top-load washers — select models
RCA top-load washers — select models
Kenmore / Sears washers — select GE-built models
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Removes water and detergent from the washer drum during drain and spin cycles
Complete assembly — includes pump motor, harness, and drain pump seal
Rated 120V, 60Hz, 1.25A with a 10-minute on / 50-minute off duty cycle
Dimensions: 5-1/4" L x 5-1/8" W x 5-1/2" H; harness and plug extend approximately 10" from motor
Plastic and metal construction rated CL.A — durable and chemical resistant
Includes drain pump seal to prevent leaks at the pump connection
Current updated replacement for discontinued WH23X24178 and WH23X27574 — direct fit
Note: The drain pump motor has been redesigned by the manufacturer — the replacement may look different from the original but fits and functions identically
Genuine GE OEM part — factory-exact fit, materials, and specifications
DIY-friendly repair — installs in 20–40 minutes with basic hand tools
Product Specifications
Part Number
WH23X28418
Supersedes
WH23X24178, WH23X27574 (both discontinued)
Part Type
Washer Drain Pump and Motor Assembly
Condition
Genuine OEM
Application
GE, Hotpoint, Haier, RCA Top-Load and Front-Load Washers
Voltage
120V AC
Frequency
60 Hz
Amperage
1.25A
Rating
CL.A
Duty Cycle
10 minutes ON / 50 minutes OFF
Dimensions
5-1/4" L x 5-1/8" W x 5-1/2" H
Harness Length
Approximately 10 inches from motor
Color
White / Black / Gray
Material
Plastic / Metal
Includes
Pump and motor with harness, drain pump seal
Compatible Brands
GE, Hotpoint, Haier, RCA, Kenmore
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Have towels and a shallow pan ready to catch residual water. For top-load GE washers, the drain pump is typically accessed from the bottom of the machine — carefully tilt the washer back onto a support or lay it on its side to reach the pump from underneath. Disconnect the outlet hose by loosening the hose clamp and pulling it free. Disconnect the electrical harness connector. Remove the mounting screws (typically three) securing the pump to the washer base. Twist and firmly pull the old pump out. Install the new WH23X28418 pump in reverse order — connect the hose, tighten the clamp, reconnect the harness, and secure the mounting screws. Restore power and water supply and run a test cycle to verify proper drainage and no leaks. Tools needed: Phillips screwdriver, flat-head screwdriver, slip-joint pliers, shallow pan.
Frequently Asked Questions
What is the relationship between WH23X28418, WH23X24178, and WH23X27574?
All three are GE washer drain pumps — WH23X28418 is the current updated part number that replaced both the discontinued WH23X24178 and WH23X27574. GE redesigned the pump motor during its production cycle, so the replacement may look slightly different from the original, but it fits and functions identically. If your washer uses either of the older numbers, order WH23X28418.
How do I know if my washer drain pump has failed?
The most common signs are standing water in the tub after a cycle, the washer stopping mid-cycle with a drain error, or loud humming during the drain phase — which indicates the motor is running but the impeller is not moving. A grinding or rattling noise suggests debris in the pump or physical damage. If the pump is completely silent during what should be the drain cycle, the motor has likely burned out and the pump needs replacement.
Does the WH23X28418 fit both top-load and front-load GE washers?
The WH23X28418 is primarily used in GE and Hotpoint top-load washers — the GTW and HTW series make up the majority of compatible models. It also fits select GE front-load models. Always verify your specific model number before ordering to confirm compatibility for your washer type.
What is the duty cycle rating and why does it matter?
The duty cycle of 10 minutes on / 50 minutes off means the pump motor is rated for up to 10 consecutive minutes of operation before requiring a 50-minute rest period. In normal washer operation this is never an issue — drain cycles are brief. However, if a drain fault causes the pump to run continuously without successfully draining, the motor can overheat. If you replace the pump due to burnout and the new pump also fails quickly, check for a drain hose blockage or control board fault that may be causing the pump to run without limit.
Is this an OEM or aftermarket part?
This is a Genuine OEM part manufactured by GE to factory specifications — the exact same drain pump and motor assembly installed in compatible models from the factory, with guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO DA34-00006C Refrigerator Door Switch
Product Overview
The XPARTCO DA34-00006C Refrigerator Door Switch controls the interior light and signals the control system when the refrigerator door is opened or closed. The DA34-00006C Refrigerator Door Switch is an aftermarket replacement that controls the interior light and signals the control board when the refrigerator or freezer door is open or closed. A faulty switch may result in lights not turning on, fan or cooling issues, or error codes. This switch restores proper operation and ensures your refrigerator functions efficiently every time the door is opened or closed.
This is a two button refrigerator door switch, fits Specific Samsung refrigerator models.
Quick Answer
If your refrigerator light stays on or does not turn on, or the unit behaves as if the door is open/closed incorrectly, the DA34-00006C door switch may be faulty. Replacing it restores correct light function and door status detection.
Replaces Part Numbers
Replaces OEM part number: DA34-00006C, DA34-00006D, DA34-00048A, 1567024, DA34-10122D, EAP2522335, ASM708482, PD00002031, AP4136952, PS4138718.
Compatibility
This refrigerator door switch is compatible with select Samsung and compatible refrigerators.
Samsung Refrigerators
French Door & Side-by-Side Models
Always verify your appliance model number before ordering.
Common Problems This Part Fixes
Refrigerator light not turning on
Interior light stays on
Cooling issues related to door detection
Control panel errors due to door status
Key Features
Controls interior light operation
Detects door open/close status
High-quality aftermarket replacement
Durable and reliable construction
Product Specifications
Part Number: DA34-00006C
Part Type: Refrigerator Door Switch
Brand: XPARTCO
Condition: New
OEM / Aftermarket: Aftermarket
Application: Refrigerator Door Detection & Light Control
Troubleshooting Guide
Light won’t turn on → Faulty door switch
Light stays on → Switch stuck or not engaging
Cooling affected when door closes → Door status not detected
When Should You Replace This Switch?
Replace this switch if the refrigerator light behaves incorrectly or if the unit is not detecting door position properly.
Installation Notes
⚠️ Disconnect power before installation. Remove the old switch from the cabinet housing, disconnect wiring, and install the new switch securely.
Related Parts
Refrigerator Light Bulb
Door Gasket
Control Board
Frequently Asked Questions
Will this switch fit my refrigerator?This switch fits many Samsung and compatible models. Always verify your model number.
What does a door switch do?It turns the interior light on/off and signals the control system when the door opens or closes.
What are signs of a bad door switch?Light not working, light staying on, or improper door detection.
Is this OEM or aftermarket?This is a high-quality aftermarket replacement part.
Shop With Confidence
Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support.
Fast Shipping Quality Tested Parts Compatibility Support
204698 Washer Door Lock
Replaces Part Numbers:204698, 213385, 2-4698, OEM20986763, AP6995586, PS2017106.
Description: This Lid Lock Kit is a replacement part for specific Speed Queen washing machine models. It is made up of lid lock components and mounting hardware that allow the washer lid to securely lock into place during operation.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
W11210463 Washer Genuine OEM Water Valve
Cross Reference Information: W11210463, W11038696, 4591539, W10701461, W10869803, W10883458, W11101906, AP6329219, PS12349269.
Description: This Washer Water inlet valve is an OEM replacement part for specific Whirlpool brand washer models. The water inlet valve controls the flow of water into the washer. It opens and closes the valve to allow water to enter the washer during the wash cycle. Then it shuts off the flow of water once the cycle is complete. If a water inlet valve goes bad, it can cause a number of issues. One of the most common symptoms is a lack of water entering the washing machine. Additionally, a faulty water inlet valve can cause the washer to overflow or leak.
XPARTCO WH11X39237 Washer Drain Pump
The XPARTCO WH11X39237 is an aftermarket replacement drain pump and filter assembly compatible with select GE, GE Profile, and GE 2-in-1 Washer/Dryer Combo front-load washers in the GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series. The drain pump is responsible for removing water from the washer drum during the drain and spin cycles — when it fails, the washer will not drain, will leave standing water in the drum, or will produce unusual noises during the drain cycle.
This complete drain pump and filter assembly operates at 120V, 60Hz, 1.2A and includes the pump motor, impeller housing, and integrated filter. It directly replaces the discontinued WH11X29539 — WH11X39237 is the current manufacturer-approved updated part number. Also replaces AP6986715, 4962370, B25-3A04, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The XPARTCO WH11X39237 Washer Drain Pump fixes GE front-load washers that won't drain, leave standing water in the drum, display drain error codes, or make loud humming or grinding noises during the drain cycle. Complete pump and filter assembly. 120V/60Hz/1.2A. Replaces discontinued WH11X29539. Compatible with GE GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series.
Common Problems This Part Fixes
Washer not draining — standing water remaining in the drum after a cycle
Drain error codes displayed on GE front-load washers (e.g. E23, E24, or pump-related codes)
Loud humming, grinding, or buzzing noise during the drain cycle
Washer stopping mid-cycle due to a drain fault
Water leaking from around the drain pump area
Drain pump running continuously but water not being expelled
Pump impeller jammed by debris and motor burned out
Replaces Part Numbers
This drain pump directly replaces the following OEM and cross-reference part numbers:
WH11X39237, WH11X29539, Hanyu B25-3A04, 9019841, PD00094541, AGE1260100, AP8054992, PS18351790.
WH11X39237 is the current manufacturer-approved replacement for the discontinued WH11X29539. If your appliance documentation lists WH11X29539, this is the correct updated part.
Compatibility
This drain pump is compatible with select front-load washers and laundry combos from the following GE product lines:
GE front-load washers — GFW510 series
GE front-load washers — GFW550 series
GE front-load washers — GFW650 series
GE front-load washers — GFW655 series
GE front-load washers — GFW850 series
GE Profile front-load washers — PFW870, PFW950, PFW955 series
GE Profile front-load washers — PFQ83 series
GE 2-in-1 Washer/Dryer Combo (select models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Complete drain pump and filter assembly — pump motor, impeller housing, and integrated filter all included
Removes water from the drum during drain and spin cycles for proper washer operation
Integrated filter traps lint, coins, and debris to prevent pump impeller damage and clogs
Electrical specs: 120V, 60Hz, 1.2A — correct for compatible GE front-load models
WH11X39237 is the current manufacturer-approved replacement for discontinued WH11X29539
Direct replacement — installs into existing pump housing with no modification required
Aftermarket replacement built to OEM-equivalent quality standards
Compatible with GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series
DIY-friendly repair — installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
WH11X39237
Supersedes
WH11X29539 (discontinued)
Part Type
Washer Drain Pump and Filter Assembly
Condition
Aftermarket Replacement
Application
GE Front-Load Washers and 2-in-1 Washer/Dryer Combos
Voltage
120V AC
Frequency
60 Hz
Amperage
1.2A
Includes
Pump motor, impeller housing, and integrated filter
Compatible Series
GFW510, GFW550, GFW650, GFW655, GFW850, PFW870, PFW950, PFW955, PFQ83
Compatible Brands
GE, GE Profile
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Place towels and a shallow pan under the pump access area to catch residual water. Remove the front lower access panel of the washer. Before removing the pump, first clean the pump filter (WH23X38617) and check for a clogged filter or debris in the pump housing — a jammed impeller is sometimes mistaken for a failed pump. If the pump motor is confirmed failed, disconnect the wire harness and drain hoses from the old pump assembly, then unscrew or unclip the pump from the mounting bracket. Install the new WH11X39237 pump assembly, reconnect the drain hoses and secure with clamps, reconnect the wire harness, and reinstall the access panel. Restore power and water supply, then run a drain-only cycle to verify proper drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan or towels.
Frequently Asked Questions
What is the difference between WH11X39237 and WH11X29539?
These are the same drain pump assembly — WH11X39237 is the current updated part number that GE issued to replace the discontinued WH11X29539. If your washer's documentation, parts diagram, or old pump label shows WH11X29539, the WH11X39237 is the correct replacement to order.
Should I check the pump filter before replacing the drain pump?
Yes — always check and clean the pump filter (WH23X38617) before replacing the drain pump. A heavily clogged filter can restrict water flow enough to mimic pump failure symptoms, and a foreign object jammed in the impeller can stall the pump motor without permanently damaging it. Remove the filter, clear any debris from the housing and impeller, and test the washer again. If the pump still fails to drain after cleaning, then pump replacement is the next step.
How do I know if my drain pump has failed?
A failed drain pump typically causes the washer to stop mid-cycle with a drain error code, or to finish a cycle with standing water in the drum. You may also hear a loud humming noise during the drain phase — this indicates the motor is running but the impeller is not turning (jammed or broken). A grinding noise suggests physical damage to the impeller or pump housing. If the pump is completely silent during the drain cycle despite power being delivered to it, the motor has likely burned out.
Is the WH11X39237 compatible with GE Profile and GE 2-in-1 models?
Yes — the WH11X39237 is compatible with select GE Profile front-load washers in the PFW870, PFW950, PFW955, and PFQ83 series, as well as select GE 2-in-1 Washer/Dryer Combo models. Always verify your specific model number before ordering to confirm compatibility.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the electrical specifications and physical dimensions of the original WH11X39237 drain pump assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO AJU75152602 Washer Water Inlet Valve
The XPARTCO AJU75152602 is an aftermarket replacement washer water inlet valve assembly compatible with select LG and Kenmore top-load washers in the larger-capacity WT7 series — including the WT7060, WT7100, WT7150, WT7155, WT7250, WT7300, WT7305, WT7400, WT7405, WT7800, WT7880, and WT7900 series. The water inlet valve is a multi-port solenoid valve mounted on the back of the washer that controls the flow of hot and cold water into the tub and dispenser compartments during fill and rinse cycles. When any valve port fails, the washer may not fill at all, fill too slowly, fill with the wrong water temperature, overfill, or leak from the valve body.
This valve assembly directly replaces 5221EA1008S, 4873914, AP6335382, EAP12580369, PS12580369, and PD00060681. It includes two integrated inlet screens to filter debris from the supply lines. Installs in 15–25 minutes with basic hand tools. Note: the AJU75152602 is for the WT7xxx larger-capacity LG top-load series — it is not the same valve as the AJU75152601, which is used on the earlier and smaller-capacity WT1xxx through WT5xxx series. Verify your model number before ordering.
Quick Answer
The XPARTCO AJU75152602 Washer Water Inlet Valve fixes LG WT7xxx-series top-load washers that won't fill, fill slowly, fill with wrong temperature, overfill, or leak from the valve. Includes 2 inlet screens. Replaces 5221EA1008S, 4873914, AP6335382, EAP12580369, PS12580369, PD00060681. Compatible with LG WT7060, WT7100, WT7150, WT7300, WT7305, WT7400, WT7405, WT7800, WT7880, WT7900 series and Kenmore (LG-built). Note: not the same as AJU75152601 — different model series.
Common Problems This Part Fixes
Washer not filling with water at all when a cycle is started
Washer filling very slowly — taking much longer than normal to reach water level
Washer filling with only cold water on a warm or hot cycle — hot solenoid failed
Washer filling with only hot water on a cold cycle — cold solenoid failed
Washer overfilling or filling continuously — valve port stuck open
Water temperature incorrect despite correct cycle selection
Water dripping into the tub between cycles — valve not sealing completely
Water leaking from the back of the washer near the valve body
Replaces Part Numbers
This water inlet valve directly replaces the following OEM and cross-reference part numbers:
AJU75152602, 4873914, 5221EA1008S, U8EONG(9F), IV-248-103, PD00060681, FIX12580369, ALG53788, AP6335382, PS12580369, DC12V 6W, IV-248-103, U8EONG(9F).
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This water inlet valve is compatible with select LG WT7 series top-load washers and related Kenmore models:
LG WT7060CV, WT7060CW
LG WT7100CW
LG WT7150CW, WT7155CW
LG WT7250CW
LG WT7300CV, WT7300CW
LG WT7305CV, WT7305CW
LG WT7400CV, WT7400CW
LG WT7405CV, WT7405CW
LG WT7800CV, WT7800CW
LG WT7880HWA
LG WT7900HBA
Kenmore 31452 and select LG-built Kenmore models
Important — AJU75152602 vs AJU75152601: These are two different valves for different LG washer generations. The AJU75152602 is for the larger-capacity WT7xxx series. The AJU75152601 is for the earlier and smaller-capacity WT1xxx through WT5xxx series. They are not interchangeable. Always verify your model number before ordering.
Key Features
Multi-port solenoid valve — controls hot water, cold water, and dispenser ports to deliver the correct water temperature and volume for each cycle phase
Includes two integrated inlet screens — filter debris and mineral deposits from the supply lines before they reach the valve seat
ABS plastic and stainless steel construction — durable and resistant to mineral buildup and corrosion
Replaces 5221EA1008S, 4873914, AP6335382, EAP12580369, PS12580369, and PD00060681
Compatible with LG WT7060, WT7100, WT7150, WT7300, WT7305, WT7400, WT7405, WT7800, WT7880, WT7900 series and Kenmore LG-built models
For WT7xxx series only — not the same as AJU75152601 (WT1xxx–WT5xxx series)
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 15–25 minutes with basic hand tools
Product Specifications
Part Number
AJU75152602
Part Type
Washer Water Inlet Valve Assembly (Multi-Port)
Condition
Aftermarket Replacement
Application
LG WT7xxx Series Top-Load Washers
Material
ABS plastic / Stainless steel
Kit Includes
Valve assembly + 2 integrated inlet screens
Note
WT7xxx series only — not interchangeable with AJU75152601 (WT1xxx–WT5xxx)
Compatible Brands
LG, Kenmore (LG-built)
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off both the hot and cold water supply valves before beginning. Pull the washer away from the wall to access the back panel. The water inlet valve is mounted on the upper rear of the washer. Photograph all wire harness connections and hose positions before disconnecting. Disconnect the two external supply hoses from the valve inlet ports. Disconnect the internal outlet hoses by squeezing the retaining clips and pulling free. Disconnect the wiring harness connectors from each solenoid port. Unscrew the mounting screws and remove the old valve. Install the new AJU75152602 valve in the same position, reconnect all internal hoses, wire harnesses, and external supply hoses in the documented positions. Restore water supply and power, then run a fill cycle to verify normal filling and check for leaks. Tools needed: Phillips screwdriver, pliers.
Frequently Asked Questions
What is the difference between AJU75152602 and AJU75152601?
These are two different water inlet valve assemblies for different generations of LG top-load washers. The AJU75152601 (which also replaces AJU73213301 and 5221EA1008F) is used on LG's earlier and smaller-capacity top-load washers in the WT1xxx, WT4xxx, and WT5xxx series. The AJU75152602 (which replaces 5221EA1008S) is for LG's larger-capacity WT7xxx series. Despite appearing similar, they have different port configurations and are not interchangeable. Always verify your specific model number before ordering.
How do I know if the water inlet valve has failed?
Common signs are the washer not filling, filling only on one temperature setting, overfilling, dripping between cycles, or leaking from the valve area. Before replacing the valve, check that both supply valves are fully open and the hoses are not kinked. You can test each solenoid coil with a multimeter — a working coil shows resistance (typically 200–500 ohms); an open circuit confirms that coil has failed. Also inspect and clean the inlet screens inside the supply port openings — mineral-clogged screens can restrict flow enough to cause the same symptoms as a failed valve.
What are the two inlet screens included with the valve?
The two mesh screens that come with the AJU75152602 install inside the hot and cold water inlet ports of the valve. They catch sediment, mineral particles, and debris from the household water supply before they can reach the solenoid valve seats. Installing fresh screens along with the new valve helps extend the valve's service life, especially in areas with hard water. If the previous valve failed due to mineral buildup rather than an electrical fault, cleaning the supply hoses before installation is also recommended.
My LG WT7300CW is only filling with cold water — is this the valve?
Filling with only cold water on a warm or hot cycle is a classic sign that the hot water solenoid coil on the inlet valve has failed. Each temperature port is controlled by its own independent solenoid — when the hot solenoid fails, only the cold port opens. Before replacing the valve, also confirm that the household hot water supply valve is fully open and that hot water is reaching the back of the washer in the supply hose. If hot water supply is confirmed and the cold-only fill persists, replace the AJU75152602 valve.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from ABS plastic and stainless steel to match the port configuration and specifications of the original AJU75152602 water inlet valve assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
