Search results for "dishwasher thermostat"

XPARTCO 35001191 Dryer Thermistor – Replaces WP35001191 – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Maintain accurate temperature control and efficient drying with the XPARTCO 35001191 Dryer Thermistor. This Dryer Thermistor is a replacement part for specific Whirlpool, Kenmore, Maytag dryer models, that is responsible for monitoring and controlling the temperature within the dryer drum. This sensor prevents overheating or under-heating, which can affect drying performance and fabric care. The thermistor communicates temperature readings to the dryer's control board, which then adjusts the heat accordingly to maintain the desired temperature settings. Replaces Part Numbers WP35001191, 35001191, 1185513, PD00003059, EAP11741828, AP6008688, PS11741828.  Compatibility This replacement dryer thermistor fits select Whirlpool, Maytag, Kenmore, Amana, Crosley, and Estate electric dryers. Example compatible models include (but are not limited to):Whirlpool WED4815EW1, Maytag MEDC215EW1, Kenmore 110.65132411. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature-sensing accuracy 🌡️ Precise Heat Regulation – Helps control dryer temperature efficiently 🔧 Reliable Sensor Performance – Sends accurate feedback to control board 💰 Cost-Effective Repair – Quality alternative to OEM thermistors 🛡️ Fixes Common Issues – Resolves overheating, no heat, long dry times, or error codes 📐 Product Specification Part Number: 35001191 Component Type: Dryer Thermistor / Temperature Sensor Application: Exhaust temperature monitoring Material: Heat-resistant sensor body with wire leads Mounting: Screw-mounted on blower housing Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to prevent electrical shock. Steps: Disconnect dryer power and remove the rear panel. Locate the thermistor on the blower housing. Disconnect the wiring harness and remove mounting screws. Install the new XPARTCO 35001191 thermistor. Reconnect wiring, reinstall panel, and restore power. Run a test cycle to confirm proper temperature regulation. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore accurate dryer temperature control — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO 165256 Dishwasher Float Switch Replaces 00165256 Product Overview The XPARTCO 165256 Dishwasher Float Switch Replaces 00165256 is designed to monitor water levels inside the dishwasher and prevent overfilling. This float switch detects rising water levels and signals the control system to stop filling, protecting your appliance from leaks and water damage. Quick Answer If your dishwasher is overfilling, not filling correctly, or leaking due to excess water, the 165256 float switch may be faulty. Replacing it restores proper water level control and prevents overflow issues. Replaces Part Numbers Replaces OEM part number: 00165256, 165256, 935359, EAP8697040, ABS10088, PD00035415, AH3439096, EA3439096, PS3439096, AP2802373, PS8697040. Compatibility This dishwasher float switch is compatible with select Bosch, Thermador, and other compatible dishwashers. Bosch Dishwashers Thermador Dishwashers Compatible European-style Dishwashers Always verify your appliance model number before ordering. Common Problems This Part Fixes Dishwasher overfilling Water leaking due to excess fill Incorrect water level detection Dishwasher not filling properly Key Features Monitors dishwasher water level Prevents overfilling and leaks High-quality aftermarket replacement Reliable and durable construction Product Specifications Part Number: 165256 Part Type: Dishwasher Float Switch Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Dishwasher Water Level Control Troubleshooting Guide Dishwasher overfills → Faulty float switch Water keeps filling → Float switch stuck or failed Dishwasher won’t fill → Switch not detecting properly When Should You Replace This Float Switch? Replace this float switch if your dishwasher is overfilling, leaking, or not detecting correct water levels. Installation Notes ⚠️ Disconnect power and water supply before installation. Access the float switch inside the tub area and install securely according to your dishwasher model. Related Parts Water Inlet Valve Dishwasher Float Assembly Control Board Frequently Asked Questions Will this float switch fit my dishwasher?This part fits many Bosch and compatible dishwashers. Always verify your model number. What does a float switch do?It monitors water levels and prevents overfilling inside the dishwasher. What are signs of a bad float switch?Overfilling, leaking, or improper water level control. Is this OEM or aftermarket?This is a high-quality aftermarket replacement part. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support  

Read more less

8558953 Dishwasher Touchpad and Control Panel Genuine OEM Fits Specific Kenmore Dishwasher Models Replaces Part Numbers: WP8558953, 8558953, 1066185, 8558928, 8563373, AP6013229, PS11746451.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WPW10181986 Oven Genuine Temperature Sensor Replaces Part Number: WPW10181986, W10181986, 1394200, 8273902, W10131826, OEM24065802, AP6016450, PS11749737. Description: This Oven Sensor Assembly is a Genuine OEM part for select Whirlpool oven models, designed to accurately measure the oven's internal temperature and communicate it to the control board. This ensures that the oven maintains the desired temperature setting during baking or roasting, providing consistent cooking results.     California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

3W40025L Genuine LG OEM Dishwasher Micro Switch – Compatible with LG Dishwashers Product Description Restore proper operation to your dishwasher with the 3W40025L Genuine LG OEM Dishwasher Micro Switch. This small but essential component detects door position or button activations, ensuring cycles start and stop correctly. A failed micro switch can cause the dishwasher not to run, stop mid-cycle, or display error codes. Replacing it with this genuine LG part restores dependable performance and safety. Replaces Part Numbers 3W40025L, D3V-16G-1C25, PD00035953, EAP5574491, AP5650845 PS5574491. Compatibility This micro switch is compatible with select LG dishwashers. Example compatible models include (but are not limited to): LG LDF7774ST, LDF8764ST, and LDF6810ST. Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 OEM Replacement – Genuine LG part for reliable performance 🔒 Cycle Safety – Ensures proper door detection and cycle control 💰 Cost-Effective OEM Part – Built to last with factory-tested quality 🛠️ Easy to Install – Small component, quick replacement with basic tools 🛡️ Fixes Common Issues – Resolves dishwashers not starting, stopping mid-cycle, or showing error codes 📐 Product Specification Part Number: 3W40025L Component Type: Dishwasher Micro Switch, 16A  125/250VAC Material: High-durability plastic housing with electrical contacts Mounting: Direct replacement switch with snap-in or screw mount Operating Conditions: Designed for standard dishwasher use Compliance: Genuine LG OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, flathead screwdriver, needle-nose pliers ⚠️ Safety First: Always disconnect the dishwasher from power before starting repairs. Steps: Disconnect power supply to dishwasher. Access control panel or door latch assembly (depending on model). Locate and remove the faulty micro switch. Install the new 3W40025L switch and reconnect wiring. Reassemble the control panel or door latch assembly. Restore power and test dishwasher operation. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Get your dishwasher running properly again — Add to Cart Now for a genuine, factory-approved fix!

Read more less

XPARTCO 242046001 Refrigerator Defrost Thermostat The XPARTCO 242046001 is an aftermarket replacement defrost termination thermostat compatible with a wide range of Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, Westinghouse, White-Westinghouse, and Kenmore refrigerators — including French door, side-by-side, and bottom-freezer models across the CFD, DGHF, E23BC, and EI23BC series. The defrost thermostat is a bi-metal safety device clipped to the evaporator coil or defrost heater tube in the freezer compartment. During the defrost cycle, it monitors the coil temperature and opens its circuit once the coil warms to roughly 50–60°F (10–15°C), which cuts power to the defrost heater. This confirms all the ice has melted and prevents the heater from continuing to run and overheating the freezer. When the thermostat fails, one of two things happens: it can fail open (the defrost heater never runs, so ice builds up on the coils until airflow is blocked and cooling fails), or it can fail closed (the heater runs too long, overheating the compartment and often producing water pooling at the bottom of the freezer or leaking onto the floor). Features a cylindrical metallic body with two blue wires and white electrical connectors. Specification code L47-22F. Wire leads approximately 7.9". It directly replaces 242046001, 240386402, 240386403, AP4508400, 1564839, AH2378768, EA2378768, PS2378768, and L47-22F. Tip: the defrost thermostat, defrost heater, and defrost timer/control board form the defrost system and often fail together — replacing them as a set while the panel is off saves a repeat repair. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 242046001 Refrigerator Defrost Thermostat fixes Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse refrigerators with excessive frost or ice buildup on the evaporator coils, fridge or freezer too warm (or too cold), the defrost cycle not activating, the refrigerator running continuously, or water pooling/leaking in the freezer. Bi-metal defrost termination thermostat — opens around 50–60°F to shut off the defrost heater. Cylindrical metal body, 2 blue wires, white connectors. Replaces 240386402, 240386403, AP4508400, 1564839, AH2378768, EA2378768, PS2378768, L47-22F. Often replaced together with the defrost heater and defrost timer. Common Problems This Part Fixes Excessive frost or ice buildup on the evaporator coils — defrost heater never running because the thermostat failed open Freezer section too warm — iced-over coils blocking airflow Refrigerator section too warm — cold air not circulating past frosted coils Freezer or fridge section too cold — erratic defrost cycling Defrost cycle not activating at all Refrigerator running continuously without cycling off Water pooling at the bottom of the freezer or leaking onto the floor — defrost heater running too long because the thermostat failed closed Reduced cooling efficiency and food spoiling faster than normal Multimeter continuity test on the thermostat shows an open circuit when cold (it should show continuity when cold) Top of the thermostat visibly popped up or bulged — a sign of failure Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This defrost thermostat directly replaces the following OEM and cross-reference part numbers: 242046001, 1564839, AFR15304, AH2378768, AP4508400, EA2378768, EAP2378768, PD00005910, PS2378768, 240386402, 1258898, 240386403, AFR1311401, AH1525990, AP3970214, EA1525990, EAP1525990, PD00029401, PS1525990, L47-22F If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: to replace a 240386402, you may need to remove the wire plugs from this thermostat. Also known as a defrost bi-metal thermostat, defrost bimetal thermostat, or defrost termination thermostat. Compatibility This defrost thermostat is compatible with select refrigerators from the following brands: Frigidaire refrigerators — CFD26 series (CFD26SDS0, CFD26WIS0/S1/S3/S4/S5/S6), CFD27 series (CFD27SDPS0, CFD27WIPB2/PB3, CFD27WIPS2/PS3, CFD27WIPW2/PW3) Frigidaire refrigerators — CFD28 series (CFD28SDS1/SDS6/SDS9, CFD28WIB5–WIBC, CFD28WIS0–WISC, CFD28WIW5–WIWC and related revisions) Frigidaire refrigerators — DGHF2360PF0, DGHF2360PF1 series Electrolux refrigerators — E23BC68 series (E23BC68JPS0–JPSAA, E23BC68JSS0/SS1/SS2), E23BC78 series (E23BC78IPS8–IPSJA, E23BC78ISS7) Electrolux refrigerators — EI23BC30 series (EI23BC30KB1/KB2/KB3, EI23BC30KS1/KS2/KS3, EI23BC30KW1/KW2/KW3), EI23BC35 series (EI23BC35KB3–KB8, EI23BC35KS3–KS7) Crosley refrigerators (select Frigidaire-built models) Gibson refrigerators (select models) Kelvinator refrigerators (select models) Tappan refrigerators (select models) Westinghouse and White-Westinghouse refrigerators (select models) Kenmore / Sears refrigerators (select Frigidaire/Electrolux-built models) Note: The defrost thermostat, defrost heater, and defrost timer/control board work together as a system — when one fails, the others have typically experienced the same age and stress. Since the rear freezer access panel must already be off and all three components are right next to each other, replacing them together in one session prevents a repeat repair. Always verify your appliance model number before ordering. Key Features Defrost termination thermostat (bi-metal) — monitors the evaporator coil temperature during the defrost cycle and cuts power to the defrost heater once the ice has melted Opens its circuit at approximately 50–60°F (10–15°C) — preventing the defrost heater from overheating the freezer compartment and saving energy Protects the evaporator from overheating during the defrost cycle Resolves "frost buildup," "too warm," "too cold," "defrost not activating," "runs continuously," and "water leaking in freezer" symptoms when caused by thermostat failure Cylindrical metallic body with two blue wires and white electrical connectors Sealed component — clips onto the evaporator coil or defrost heater tube Specification code L47-22F — opens at approximately 47°F Wire leads approximately 7.9" — connect inline with the defrost heater Tube-mount clip-on design — latches onto the evaporator tubing Replaces 240386402, 240386403, AP4508400, 1564839, AH2378768, EA2378768, PS2378768, and L47-22F Compatible with Frigidaire CFD26/CFD27/CFD28/DGHF series, Electrolux E23BC/EI23BC series, plus Crosley, Gibson, Kelvinator, Tappan, Westinghouse, White-Westinghouse, and Kenmore Frigidaire-built refrigerators Often replaced together with the defrost heater and defrost timer/control board as a paired defrost-system repair Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number XP242046001 Part Type Refrigerator Defrost Termination Thermostat (Bi-Metal) Condition Aftermarket Replacement Application Refrigerators (Frigidaire/Electrolux platform) Specification Code L47-22F Opening Temperature Approximately 47°F (L47-22F rating) Function Cuts power to the defrost heater once ice has melted Body Cylindrical metallic Wiring Two blue wires (approx. 7.9") with white electrical connectors Mounting Tube mount — clips onto evaporator coil or defrost heater tube Location Freezer compartment, behind rear evaporator panel Also Known As Defrost bi-metal thermostat, defrost termination thermostat Often Paired With Defrost Heater, Defrost Timer / Control Board Compatible Brands Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, Westinghouse, White-Westinghouse, Kenmore Installation Notes ⚠️ Unplug Refrigerator and Move Perishable Food Before Starting — Wear Work Gloves Unplug the refrigerator from the electrical outlet and safely store any food that could spoil while the power is off. Wear work gloves to protect your hands. The defrost thermostat is located in the freezer compartment behind the rear evaporator access panel. Remove all freezer shelves, drawers, and the ice maker (if equipped) to clear access to the back wall. If there's heavy ice buildup covering the coils, allow the freezer to thaw completely before continuing — never chip or pry ice off the evaporator coils, as the aluminum fins damage easily and a damaged coil is a far more expensive repair. Remove the screws securing the rear evaporator access panel and carefully detach it to expose the evaporator coils, defrost heater, and defrost thermostat. Locate the thermostat — it's the small cylindrical metal component clipped onto the evaporator coil or the defrost heater tube, with two blue wires. Photograph the wiring connections and mounting position before disconnecting. Carefully disconnect the electrical connectors from the old thermostat, noting their orientation. Release the mounting clip and remove the old thermostat. Clip the new 242046001 thermostat onto the coil or heater tube in the exact same position — good thermal contact with the coil is essential for the thermostat to sense the temperature correctly. Reconnect the electrical connectors. While the panel is open, inspect the defrost heater and defrost timer/control board — if either is damaged or you're chasing a defrost problem, this is the ideal time to replace them too. Reinstall the rear access panel, shelves, drawers, and ice maker. Plug the refrigerator back in and allow several hours for the unit to return to its set temperature. Tools needed: Phillips screwdriver, 1/4" nut driver, work gloves. Frequently Asked Questions What does a defrost thermostat actually do? It's the "off switch" for your refrigerator's defrost heater. Frost naturally accumulates on the evaporator coils during normal cooling. Periodically, the defrost timer/control board turns on the defrost heater to melt that frost. The defrost thermostat — a bi-metal switch clipped right to the coil — monitors the coil's temperature during this cycle. When the coil warms to approximately 47°F (its L47-22F rating — indicating all the ice has melted), the thermostat opens its circuit and cuts power to the heater. This stops the heater before it overheats the freezer compartment, and saves energy. Without a working thermostat, the defrost cycle either never runs (ice builds up) or runs too long (overheating and water pooling). I found water pooling in my freezer — is the defrost thermostat the cause? Quite possibly. A defrost thermostat that fails closed (stuck in the "on" position) lets the defrost heater run far longer than it should. The excess heat melts more than just the frost on the coils, producing more water than the drain can handle — which pools at the bottom of the freezer and can leak onto the floor. This is a commonly misdiagnosed symptom: many people assume they have a water line leak when the actual culprit is a failed defrost thermostat. If you're seeing unexplained water in the freezer or on the floor and there's no obvious water line issue, check the defrost thermostat. Also verify the defrost drain isn't clogged, which produces similar symptoms. How do I test the defrost thermostat? With the refrigerator unplugged, disconnect the thermostat's wire connectors and set your multimeter to continuity mode. A working defrost thermostat should show continuity when it's cold (below its opening temperature — which it will be if it's been in the freezer). If it reads open (no continuity) while cold, the thermostat has failed and needs replacement. For a more thorough test, place the thermostat in ice water (should show continuity), then warm it above its ~47°F opening point (should open — no continuity). If it doesn't switch at the correct temperatures, replace it. Another visual check: if the top of the thermostat has popped up or bulged, that's a sign it has failed. Should I replace the defrost heater and timer at the same time? Yes, it's strongly recommended. The defrost thermostat, defrost heater, and defrost timer/control board work together as a system — the timer initiates the defrost cycle, the heater melts the frost, and the thermostat terminates the cycle when the coil is clear. When one component fails, the others have typically experienced the same age and thermal stress, and a near-term failure of another defrost component is common. Since the rear access panel is already off and all three components are right there next to each other, replacing them together in a single session prevents a repeat repair down the road. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured to match the L47-22F specification (opening at approximately 47°F), bi-metal switching function, cylindrical body, two-blue-wire connector configuration, and tube-mount clip of the original 242046001 defrost termination thermostat used in compatible Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, Westinghouse, and Kenmore refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine GE OEM Part GE WD24X25325 Dishwasher Genuine Fan Vent Assembly Genuine GE door-vent blower/fan assembly for select GE and Haier dishwashers. Product Overview The GE WD24X25325 Dishwasher Fan Vent Assembly is a genuine OEM replacement used in the dishwasher door ventilation system. The blower circulates air through the door vent during the drying portion of the cycle to help reduce retained moisture and improve drying performance. Quick Answer WD24X25325 is a Genuine GE OEM dishwasher door-vent blower/fan motor assembly. It is used on select GE and Haier dishwashers and helps move moist air through the door vent during drying. Common Problems This Part May Fix Poor drying performance Excess moisture remaining after a cycle Door vent fan does not run Unusual noise from the vent/blower area Moist air is not being exhausted through the door vent Replaces and Cross-References WD24X25325, 265D2664G005, U40G12BS3A5-51, AGE25072, AP6972063, EAP12726435, PD00073154, PS12726435. Cross-reference numbers are supplied for identification. Always verify the complete dishwasher model number before ordering. Compatibility Fits select GE and Haier dishwashers. Compatible model examples include: CDT800P2N0S1 CDT805P2N0S1 CDT845P2N3S1 DDT700SBN0TS GDF645SSN0SS GDT645SFN3DS GDT665SFN0DS GDP665SYN3FS PDT715SYN2FS PDT715SFN0DS PDP715SYN3FS QDP555SYN0FS Important: This is only a partial compatibility list. Confirm the exact dishwasher model number before purchase because similar models may use a different vent or blower assembly. Key Features Genuine GE Appliances OEM part Complete door-vent blower/fan assembly Circulates air through the dishwasher door vent Helps reduce moisture during drying For select GE and Haier dishwashers Product Specifications Manufacturer GE Appliances Manufacturer Part Number WD24X25325 Part Type Dishwasher Fan Vent / Door Vent Blower Assembly Condition New Part Quality Genuine OEM Application Dishwasher Door Ventilation / Drying System Approx. Shipping Weight 0.5 lb Installation Notes Disconnect electrical power to the dishwasher at the breaker before service. Access the door vent assembly according to the appliance service procedure. Disconnect the wiring connector carefully before removing the old fan assembly. Transfer or reuse any hardware only as directed for the specific model. Confirm the vent path is clear and the new assembly is fully seated before reassembly. Diagnostic note: Poor drying can also result from rinse-aid settings, heating-system faults, blocked vent passages, or control issues. Confirm the fan assembly is defective before replacing it. Frequently Asked Questions Is WD24X25325 a Genuine GE OEM part? Yes. GE Appliances identifies WD24X25325 as a genuine replacement fan vent assembly. What does this fan assembly do? It circulates air through the dishwasher door vent to help reduce moisture during the drying stage. Does it fit every GE dishwasher? No. It fits specific GE and Haier models. Verify the complete model number before ordering. Is this only the fan motor? This listing is for the complete WD24X25325 fan vent / door-vent blower assembly as supplied by GE. Shop With Confidence Use your dishwasher's complete model number to confirm fitment before purchase. Genuine GE OEMFan Vent AssemblyModel Verification RecommendedFast U.S. Shipping

Read more less

A00126401 Genuine OEM Frigidaire Dishwasher Drain Pump Motor The A00126401 is a genuine Frigidaire OEM drain pump motor assembly for Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, and Kenmore dishwashers. At the end of each wash cycle, this pump is what actually pushes the used wash water out of the tub and through the drain hose, clearing the way for the next fill. An internal impeller spins to create that flow, drawing water in and forcing it out through the drain line. Rated 120V, 60Hz, 35W, 0.8A, 3600RPM, with 1/4" male terminals, this assembly includes the pump motor, impeller, and seal. Common causes of failure include clogs from food particles or debris interfering with the impeller, worn or damaged impeller blades, and electrical failure of the motor itself. A failing drain pump typically shows up as water not draining from the dishwasher, water pooling at the bottom of the tub after a cycle, a grinding or humming noise from the pump area, or the dishwasher refusing to start a new cycle because it detects standing water left over from the last one. It directly replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, and EAP2363535. Quick Answer The A00126401 Genuine OEM Frigidaire Dishwasher Drain Pump Motor fixes Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, and Kenmore dishwashers that won't drain, pool water at the bottom of the tub, make grinding or humming noises, or won't start a new cycle due to leftover water. 120V, 60Hz, 35W, 0.8A, 3600RPM. Replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, EAP2363535. Before replacing the pump, check the drain hose and sump screen for a simple clog — one customer replaced the pump, still had no drainage, and found a clogged drain hose was the actual cause. Common Problems This Part Fixes Dishwasher won't drain at the end of the cycle Water pooling at the bottom of the tub after a completed cycle Grinding or humming noise coming from the pump area Dishwasher won't start a new cycle because it detects leftover water from the previous one Dishes not getting properly cleaned due to poor water circulation Pump running but producing little or no actual drainage Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers: A00126401, 154736201, 3015405, 5304492415, PD00000922, EAP2363535, AFR20557, AP5690431, PS8689824 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Frigidaire dishwashers, and also fits select Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, and Kenmore/Sears dishwashers built on the same platform. Note: This assembly includes the pump motor, impeller, and seal. Whether a check valve flapper is included can vary by supplier batch — inspect your old pump's flapper condition before assuming one is included, and contact our support team if you need to confirm. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified motor speed and impeller design Pumps water out of the tub and through the drain hose at the end of each cycle Resolves "won't drain," "water pooling," "grinding or humming noise," and "won't start due to leftover water" symptoms caused by pump failure Includes pump motor, impeller, and seal Rated 120V, 60Hz, 35W, 0.8A, 3600RPM 1/4" male terminals for a direct plug-in electrical fit Direct drop-in replacement — no modification required Replaces AP5690431, 154736201, 3015405, 5304492415, PS8689824, DW26401, PD00000922, and EAP2363535 Compatible with Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, and Kenmore dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number A00126401 Part Type Dishwasher Drain Pump Motor Assembly Condition Genuine OEM Brand Frigidaire Voltage 120V Frequency 60 Hz Wattage 35 W Amperage 0.8 A Motor Speed 3600 RPM Terminals 1/4" male Kit Contents Pump motor, impeller, seal Dimensions Approx. 3-1/4"L x 2-1/2"W x 3-3/4"H Color White / Green Repair Difficulty Easy to Moderate — under an hour Quantity 1 drain pump motor assembly Compatible Brands Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Westinghouse, Tappan, Ikea, Kenmore Installation Notes ⚠️ Unplug Dishwasher Before Starting — Rule Out A Simple Clog First Before replacing the pump, check the drain hose and the sump screen at the bottom of the tub for a clog — food debris and buildup in the hose can produce identical "won't drain" symptoms to a failed pump, and clearing a clog costs nothing but a few minutes. One customer replaced the pump entirely, still had no drainage, and only afterward discovered the actual cause was a clogged drain hose; disconnecting and running a cycle without the hose attached can help confirm whether the pump itself is pushing water. Once you've confirmed the pump needs replacing, disconnect power at the outlet or shut off the circuit breaker, and pull the dishwasher out from under the counter for access to the underside — removing the two screws securing it to the counter first. Have a drain pan or towels ready for residual water. Photograph the wiring and hose connections before disconnecting anything. Disconnect the two wire connectors from the old pump, remove the three screws securing it in place, and disconnect the hose connections, then pull the old pump free. Install the new A00126401 in the same position, reconnect the hose connections, and reconnect the two wire connectors. Secure the pump with its three mounting screws. Slide the dishwasher back into place and secure it to the counter, restore power, and run a full test cycle to confirm normal draining with no leaks or unusual noise. Tools needed: Phillips screwdriver, flat-blade screwdriver, needle-nose pliers, drain pan, work gloves. Frequently Asked Questions My dishwasher won't drain. How do I know if it's actually the pump and not something simpler? Check the drain hose and the sump screen at the bottom of the tub for a clog first — this is a genuinely common cause of "won't drain" symptoms and costs nothing to rule out. If the hose and screen are clear and the pump still won't run, test the pump motor with a multimeter for continuity. If there's no continuity, or the pump is getting power but still won't run, replacement is the correct fix. I already replaced the pump and it's still not draining. What should I check next? This has happened to real customers, and the cause was ultimately a clogged drain hose rather than the pump itself. If replacing the pump didn't solve the drainage problem, disconnect the drain hose and run a test cycle to see whether water is being pushed out at all — if it is, the hose downstream is the likely culprit and worth snaking out or replacing. Does this kit include the check valve flapper? This varies by supplier batch — this assembly reliably includes the pump motor, impeller, and seal, but flapper inclusion isn't consistent across all sources. Inspect your old pump's flapper for wear or damage before installation, and contact our support team if you need to confirm whether a flapper is included with your specific order. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original motor speed, impeller design, and terminal configuration of the drain pump originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3977393 Dryer Thermal Cut Off (309°F) – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Protect your dryer from overheating with the XPARTCO 3977393 Dryer Thermal Cut Off (309°F). This high-quality aftermarket replacement is a critical safety component designed to permanently interrupt power to the heating circuit if temperatures exceed 309°F (154°C). A blown thermal cut off can result in no heat. Replacing it with this reliable XPARTCO component helps restore safe operation and prevent further damage to heating elements or internal components. XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and performance. Replaces Part Numbers 3977393, AP3094244, PS334299, EAP334299 Compatibility This replacement dryer thermal cut off fits select Whirlpool, Maytag, Kenmore (Whirlpool-manufactured), Amana, Estate, and Roper dryers. Commonly installed on the heater housing assembly. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature rating and fit 🌡️ 309°F (154°C) Cut-Off Rating – Designed for high-heat safety protection 🛡️ Prevents Overheating Damage – Protects heating element and dryer components 🧩 Direct-Fit Design – Installs easily without modification 💰 Cost-Effective Repair – Affordable alternative to OEM thermal cut offs 📐 Product Specification Part Number: 3977393 Component Type: Dryer Thermal Cut Off Temperature Rating: 309°F (154°C) Function: One-time over-temperature safety cutoff Mounting: Screw-mounted Application: Dryer heater housing assembly Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Unplug the dryer before servicing to avoid electrical shock. Basic Steps: Disconnect dryer power. Remove rear panel to access heater housing. Locate and disconnect the old thermal cut off. Remove mounting screws and install the new XPARTCO 3977393 cut off. Reconnect wiring and reassemble the dryer. Restore power and test operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore dryer safety and prevent overheating — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

WP4449751 Genuine OEM Whirlpool Oven High Limit Thermostat The WP4449751 is a Genuine OEM Whirlpool replacement oven high limit thermostat compatible with a wide range of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ovens, wall ovens, microwave-oven combinations, and ranges. The high limit thermostat is a critical safety device mounted near the oven cavity — it continuously monitors the oven's temperature and cuts off electrical power to the heating element if the oven exceeds its safe operating temperature. When the oven temperature drops back to normal, the thermostat closes and allows normal operation to resume. This backup safety layer protects against fires, damage to the oven, and unsafe cooking conditions when the main temperature control fails. Rated to trip at approximately 335°F (170°C). Common causes for the high limit thermostat to trip include a faulty control board, cooling fan failure, blocked ventilation, poor door sealing, disrupted air circulation, or an abnormal self-cleaning cycle. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the WP4449751 directly replaces 4449751, 1550872, AP6009390, AH2375382, EA2375382, PS2375382, PS11742549, EAP11742549, and AH11742549. Installs in 30–45 minutes with basic hand tools by experienced DIYers. This is a safety component in a 240V oven circuit — proceed only if you're comfortable with high-voltage electrical work, or call a qualified appliance technician. Quick Answer The WP4449751 Genuine OEM Whirlpool Oven High Limit Thermostat fixes Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, and Kenmore ovens with symptoms including oven not heating, oven overheating, uneven heating, oven failing to start, and self-clean door won't unlock after cycle. 335°F (170°C) trip temperature — cuts off power to heating element on overheat, then resets when temperature returns to normal. Genuine OEM. Replaces 4449751, 1550872, AP6009390, AH2375382, EA2375382, PS2375382, PS11742549, EAP11742549, AH11742549. Compatible with WOS/WOD wall ovens, KOSE/KODE/KOCE series, JJW/JMW/JDRP/JDR series, and many more. Common Problems This Part Fixes Oven not heating at all — high limit thermostat tripped open Oven overheating — thermostat failing to trip when needed (rare failure mode) Inconsistent oven temperatures leading to undercooked or overcooked food Oven fails to start when powered on Oven door won't unlock after a self-cleaning cycle completes Uneven heating — hot spots or cold spots inside the oven cavity Oven cuts off heat mid-cycle without reaching set temperature F-code or thermostat-related error displayed on the control panel Multimeter continuity test on the thermostat shows an open circuit at room temperature Visible damage or discoloration on the thermostat housing from a prior overheat event Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This oven high limit thermostat directly replaces the following OEM and cross-reference part numbers: WP4449751, 4449751, 1550872, AP6009390, AWP47600, EAP2375382, PD00025977, PS11742549 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This high limit thermostat is compatible with select ovens, wall ovens, ranges, and microwave-oven combinations from the following brands: Whirlpool wall ovens — WOS series (WOS31ES0JS, WOS51EC0AS, WOS51EC0HS, WOS51EC7HW02, WOS51EC7HW21, WOS72EC0HS/HV, WOS72EC7HS/HV, WOS92EC0/EC7 all revisions, WOS97ES0ES series) Whirlpool double wall ovens — WOD series (WOD51EC0AW03, WOD51EC7HS, WOD93EC7AS) Whirlpool combination wall ovens — WOC54EC0/EC7 series KitchenAid wall ovens — KOSE, KODE, and KOCE series (KOSE500ESS, KODE500ESS, KOCE500ESS, KOCE500EBL00/EBL01/EBL02/EBL04/EBL05) Jenn-Air wall ovens — JJW, JMW, JDRP, and JDR series (JJW2427DB/DS 00/01, JJW2430DS, JJW3430DS, JMW2430DS, JDRP430HL/HM 00/01, JDRP430WP00, JDRP436HL/HM/WP series, JDRP536HL/HM/WP series) Maytag wall ovens and ranges (select models) Amana wall ovens (select models — AWO6313SFB00/02, AWO6313SFS00/02, AWO6313SFW00/02) KitchenAid ranges — KDRS407 series (KDRS407VBK01, KDRS407VBU01, KDRS407VSS00) Whirlpool ranges — IBD350DS00, IBS300DS00, IBS350DS00 series Magic Chef, Admiral, Norge, Roper wall ovens (select Whirlpool-built models) Kenmore / Sears wall ovens (select Whirlpool-built models) Suitable for single or double electric wall ovens and microwave-oven combination units Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance High limit thermostat (safety switch) — cuts off power to the oven's heating element when temperature exceeds 335°F (170°C) to prevent overheating damage or fire Auto-reset design — closes and restores normal operation when the oven temperature returns to safe range Precision-calibrated to Whirlpool factory specifications for accurate trip temperature and reliable safety response One-year Whirlpool warranty on Genuine OEM parts Replaces 4449751, 1550872, AP6009390, AH2375382, EA2375382, PS2375382, PS11742549, EAP11742549, and AH11742549 Compatible with Whirlpool WOS/WOD/WOC series, KitchenAid KOSE/KODE/KOCE series, Jenn-Air JJW/JMW/JDRP/JDR series, plus Maytag, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ovens Fits single wall ovens, double wall ovens, ranges, and microwave-oven combination units Resolves "oven won't heat," "overheating," "uneven heating," "self-clean door stuck locked," and "won't start" symptoms when caused by a failed high limit thermostat For experienced DIYers or qualified appliance technicians — this is a safety component in a 240V oven circuit Installation typically takes 30–45 minutes with basic hand tools Product Specifications Part Number WP4449751 Part Type Oven High Limit Thermostat (Safety Switch) Condition Genuine OEM Application Wall Ovens, Ranges, Microwave-Oven Combinations (Whirlpool platform) Trip Temperature 335°F (170°C) Type Auto-Reset (closes when temperature returns to safe range) Warranty One-Year Whirlpool Warranty (Genuine OEM) Compatible Brands Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Turn Off Power at Breaker Before Starting — This Is a 240V Oven Circuit — Wear Work Gloves Disconnect power at the household breaker before beginning — this is a 240V circuit and there is a serious risk of electrical shock if power is not fully disconnected. Verify power is off with a voltage tester before touching any wiring. Wear work gloves and safety glasses. Allow the oven to cool completely before beginning (several hours after any recent cooking). The high limit thermostat is typically mounted on the rear or side of the oven cavity, accessed by removing the back panel of the appliance (for freestanding ranges) or the front trim/service panel (for wall ovens). The exact location varies by model — consult your appliance's service diagram before starting. Photograph all wire connections and mounting details before disconnecting anything. Disconnect the wire terminals from the old thermostat (typically two spade-terminal wires). Remove the mounting screws or clips holding the thermostat to the oven cavity, and lift it out. Install the new WP4449751 in the exact same position and orientation — the thermostat must be in good thermal contact with the oven cavity to function correctly. Secure the mounting hardware and reconnect the wires to their correct terminals. Reinstall the access panels. Restore power at the breaker and test the oven — start with a low-temperature bake cycle to confirm normal heating operation before running a high-temperature or self-clean cycle. Tools needed: Phillips screwdriver, 1/4" nut driver, voltage tester (essential), work gloves, safety glasses. Frequently Asked Questions Why did my high limit thermostat trip in the first place? A high limit thermostat trips because the oven exceeded its safe operating temperature — meaning something upstream in the temperature control chain failed to shut off the heating element when it should have. Common causes are: a failed oven control board (relay stuck closed), a failed cooling fan (allowing the oven cavity or electronics to overheat), blocked or restricted ventilation, poor door sealing (letting the cavity overheat), disrupted air circulation, or an abnormal self-cleaning cycle. Before installing the new thermostat, investigate and address the underlying cause — otherwise the new thermostat will trip again in short order. Also inspect the ventilation, oven door gasket, and cooling fan while you have the appliance open. What's the difference between a high limit thermostat and the operating thermostat? These are two different components serving two different roles. The operating thermostat (or the oven control board with its temperature sensor) is the primary component that maintains the oven at your set temperature by cycling the heating element on and off during normal operation — it opens and closes at your selected temperature (e.g., 350°F). The high limit thermostat (WP4449751) is a backup safety device that only trips when the oven temperature far exceeds normal operation (335°F over the cavity's safe threshold), typically because the operating thermostat or control has failed. If the high limit thermostat trips, both need to be checked — the operating thermostat may also need replacement. Does the high limit thermostat reset itself, or does it need to be replaced after tripping? The WP4449751 is an auto-reset thermostat — it closes automatically once the oven cools back to a safe temperature, allowing normal operation to resume. If your oven is heating normally again after cooling, the thermostat is likely still functional (the underlying overheating cause needs investigation). However, if the thermostat has failed permanently open — often the result of repeated overheat events or age — it will need replacement. Test with a multimeter set to continuity: a working thermostat shows continuity at room temperature. If it reads open (infinite resistance) when cold, it has failed and needs replacement. Why does my self-cleaning cycle leave the oven door locked and the oven won't heat? This is a classic symptom of a high limit thermostat that tripped during the self-clean cycle. Self-cleaning cycles run at extreme temperatures (800–1000°F) and stress every component in the oven — if the ventilation, door gasket, or cooling fan can't keep up, the high limit thermostat will trip open. Once tripped, the oven can't heat OR unlock the self-clean door lock mechanism, leaving the door stuck closed. Once the thermostat cools and closes (or is replaced), the door lock releases and normal operation resumes. If self-clean cycles routinely trip the thermostat, investigate whether the ventilation, cooling fan, or door gasket are causing the problem. Can I do this repair myself, or should I hire a technician? Replacing an oven high limit thermostat is a manageable DIY repair for someone comfortable with mechanical work and electrical connections, but this is a 240V circuit and the thermostat is a safety component — any error can create a serious safety risk. If you have experience with appliance repair, follow the safety precautions carefully (breaker off, voltage tester, correct thermostat orientation), and can confirm the wiring connections are secure, this is a feasible DIY. If you've never worked with 240V appliance circuits before, hiring a qualified appliance technician is the safer option. Also identify and address whatever caused the original overheat event — otherwise the new thermostat will trip again. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same high limit thermostat installed in compatible Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ovens from the factory — guaranteed fit, materials, and performance. Backed by Whirlpool's one-year warranty on Genuine OEM parts. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11175771 Genuine OEM Whirlpool Dishwasher Water Valve The W11175771 is a genuine Whirlpool OEM water inlet valve for Whirlpool, Kenmore, KitchenAid, Amana, Crosley, Magic Chef, and Inglis dishwashers, located behind the lower kick plate panel in either the right or left corner. This valve controls the flow of water into the appliance during the wash cycle — an electrical solenoid plunger opens and closes the valve to admit exactly the right amount of water at the appropriate stages of the dishwasher's cycle. Measuring approximately 3.37" in height, this is a superseding part, replacing the earlier W10872255 and W11130744 valve numbers so older models can be updated with the current version. Over time, a screen inside the valve can become clogged with sediment — this screen isn't designed to be cleaned or serviced, so a clog means the whole valve needs to be replaced. A failing valve produces a clear set of symptoms: the dishwasher not filling with enough water or not filling at all, leaking into the dishwasher while not in use, or overfilling with too much water. It directly replaces AP6339872, W10195047, W10327250, W10872255, W11130744, W10327249, W10316814, and W11130743. Quick Answer The W11175771 Genuine OEM Whirlpool Dishwasher Water Valve fixes Whirlpool, Kenmore, KitchenAid, Amana, Crosley, Magic Chef, and Inglis dishwashers that aren't filling with water, are leaking, or are overfilling. Located behind the lower kick plate panel. Replaces AP6339872, W10195047, W10327250, W10872255, W11130744, W10327249, W10316814, W11130743. While the dishwasher is disassembled for this repair, consider also checking or replacing the water supply adapter, since it's in the same area and easy to inspect at the same time. Common Problems This Part Fixes Dishwasher not filling with enough water, or not filling at all Water leaking into the dishwasher while it's not in use Dishwasher overfilling with too much water High-pitched whining sound while the dishwasher is filling Poor washing results or an error code related to water fill Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers: W11175771, 3015468, 328C151-T, 4451572, 4843711, AP5804368, AP6024301, AP6339872, EAP11738107, EAP12578165, EAP3406951, AWP43823, PD00052484, PS11738107, PS12578165 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select Whirlpool dishwashers, and also fits select Kenmore, KitchenAid, Amana, Crosley, Magic Chef, and Inglis dishwashers built on the Whirlpool platform, including model numbers such as WDF130PAHB1, WDF130PAHB2, WDF130PAHS1, WDF130PAHS2, WDF130PAHW2, WDF330PAHB3, WDF330PAHW4, WDF331PAHB1, WDF520PADB9, WDF520PADM, WDT730PAHZ, WDT720PADM, WDF330PAHS, ADB1400AGW, KDTE104ESS1, and Kenmore 66513222N410 through N414. Note: Always verify your full model number before ordering, since similar-looking dishwasher water valves can vary between models. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate Regulates water flow into the dishwasher via an electrical solenoid plunger Resolves "won't fill," "leaking," "overfilling," and "whining noise" symptoms caused by valve failure Superseding part — current replacement for the earlier W10872255 and W11130744 valves Approximately 3.37" in height Direct drop-in replacement — matches the original mounting and hose connections Replaces AP6339872, W10195047, W10327250, W10872255, W11130744, W10327249, W10316814, and W11130743 Compatible with Whirlpool, Kenmore, KitchenAid, Amana, Crosley, Magic Chef, and Inglis dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11175771 Part Type Dishwasher Water Inlet Valve Condition Genuine OEM Brand Whirlpool Location Behind the lower kick plate panel, right or left corner Height 3.37" Supersedes W10872255, W11130744 Screen Serviceable No — replace valve if clogged Repair Difficulty Easy to Moderate — approx. 15 to 30 minutes Quantity 1 valve Compatible Brands Whirlpool, Kenmore, KitchenAid, Amana, Crosley, Magic Chef, Inglis Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Remove the bottom front kick plate to access the interior, where the valve is located behind the panel in either the right or left corner depending on your model. Photograph the wiring and hose connections before disconnecting anything. Disconnect the water line, the electrical connector, and remove the mounting screws securing the old valve, then pull it free. Install the new W11175771 in the same position, securely reconnect the water line and electrical connector, and secure the mounting screws. While you're in this area, it's worth inspecting the water supply adapter for wear, since it's a related part in the same location that's easy to check while everything is already accessible. Reinstall the kick plate, restore the water supply and power, then run a test cycle to confirm the dishwasher fills correctly with no leaks. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions My dishwasher isn't filling with water at all. Is this the right part? Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the dishwasher, a solenoid failure or internal blockage can prevent any water from entering at all, stopping the wash cycle from proceeding. Can I just clean the valve's screen instead of replacing the whole thing? No — the screen inside this valve isn't designed to be cleaned or serviced. If it becomes clogged with sediment from your household water supply, the entire valve should be replaced rather than attempting to clean or repair the screen itself. My dishwasher makes a high-pitched whining sound while filling. Is that this valve? Yes, this is a documented symptom of a failing water inlet valve. One customer specifically traced an "obnoxious high-pitched whining sound when filling with water" to this exact valve and resolved it with a straightforward replacement in about 15 minutes. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

DA32-00006W Genuine Samsung OEM Refrigerator Thermistor Refrigerator defrost temperature sensor. Replaces Part Numbers: DA32-10105R, DA32-00006W, DA32-00006U, 2030342, DA32-00006B, DA32-00006C, DA32-00006D, DA32-00006L, DA32-00006M, DA32-00006T, DA32-00006V, AP4135567, PS4138681. The Samsung Defrost Sensor is a genuine part designed specifically for Samsung refrigerators. This sensor, sometimes referred to as a defrost thermostat or defrost temperature sensor, is an integral part of your refrigerator's defrost system.  

Read more less