Search results for "refrigerator water valve"

WH13X10029 Genuine OEM GE Washer Water Valve The WH13X10029 is a genuine GE OEM water inlet valve for GE, Hotpoint, Haier, Monogram, and Café front-load washers. This is a 2-inlet, 3-outlet valve assembly built around three internal solenoids: two work together during the wash portion of the cycle, opening in different combinations depending on the wash temperature you select, while the third solenoid handles the dedicated cold-only rinse. Because three separate solenoids share one valve body, a failure in any single one of them can affect only part of your washer's fill behavior while the rest continues working normally. Rated 120V, 60Hz, and measuring approximately 5-3/8"L x 3-1/8"W x 2-1/2"H, this valve ships as a complete 3-solenoid assembly with its mounting bracket included. Common failure symptoms include the washer continuing to fill after it should have stopped, slow filling, or a complete failure to fill on one specific water temperature setting while others work fine. It directly replaces AP4303282, WV10029, 33090039, 1475762, AH1482392, EA1482392, EAP1482392, PD00001515, and PS1482392. As a genuine OEM part, the WH13X10029 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance. Quick Answer The WH13X10029 Genuine OEM GE Washer Water Valve fixes GE, Hotpoint, Haier, Monogram, and Café front-load washers that won't shut off after filling, fill slowly, or won't fill on a specific temperature setting (such as cold-only rinse) while other settings work fine. 2-inlet, 3-outlet, 3-solenoid valve assembly with mounting bracket, 120V, 60Hz, 5-3/8"L x 3-1/8"W x 2-1/2"H. Replaces AP4303282, WV10029, 33090039, 1475762, AH1482392, EA1482392, EAP1482392, PD00001515, PS1482392. Genuine OEM — manufactured by GE to factory specifications for guaranteed fit, materials, and performance. Common Problems This Part Fixes Washer keeps filling and won't shut off, even after reaching the correct level Washer fills much more slowly than it used to Washer won't fill at all on one specific temperature setting while other settings work normally Cold-only rinse cycle failing to fill while wash-cycle fills work fine (or vice versa) Cycle stalling at the fill step and never advancing to wash Water leaking or dripping near the valve connections Washer stopping mid-cycle due to a fill-related fault Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water valve directly replaces the following OEM and cross-reference part numbers: WH13X10029, 33090039, PD00001515, EAP1482392, AGE26067, AH1482392, EA1482392, AP4303282, PS1482392. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select GE, Hotpoint, Haier, Monogram, and Café front-load washers, including model families such as GFA, GFW, GMA, and WBV, and specific models such as GFWS1600H, GFWS1605H, GFWS1700H, and GFWS1705H. Note: This valve is specific to GE's front-load washer platform. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified solenoid design and flow-rate calibration Complete 3-solenoid water valve assembly — 2 inlets (hot and cold), 3 outlets Two solenoids manage the wash-cycle fill combinations by temperature selection; a third handles cold-only rinse Resolves "won't shut off," "fills slowly," and "won't fill on a specific temperature setting" symptoms caused by valve failure Includes the mounting bracket — no need to transfer hardware from the old valve Rated 120V, 60Hz Approximately 5-3/8"L x 3-1/8"W x 2-1/2"H Direct drop-in replacement — matches the original mounting and hose connections Replaces AP4303282, WV10029, 33090039, 1475762, AH1482392, EA1482392, EAP1482392, PD00001515, and PS1482392 Compatible with GE, Hotpoint, Haier, Monogram, and Café front-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WH13X10029 Condition Genuine OEM Part Type Washer Water Inlet Valve (2-In / 3-Out, 3-Solenoid) Brand GE Application Front-Load Washers Voltage 120V Frequency 60 Hz Inlets 2 (hot and cold) Outlets 3 Solenoids 3 (one double, one single, one dedicated cold-rinse) Dimensions 5-3/8"L x 3-1/8"W x 2-1/2"H Kit Contents Valve assembly + mounting bracket Quantity 1 valve assembly Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Stackable Units May Need A Second Person Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. If your washer is part of a stacked laundry center, the dryer sitting on top will need to be removed first to access the top of the washer — this is much easier with a second person helping to lift and support the dryer safely. Remove the screws securing the top panel of the washer, then slide the panel back and lift it off to access the valve assembly. Disconnect the hot and cold water supply hoses from the back of the valve, keeping a towel handy for residual water. Photograph the wiring and hose connections before disconnecting anything, since this valve has multiple solenoids and outlet hoses that must be reconnected in the correct positions. Disconnect the electrical connectors and the three outlet hoses from the old valve, then remove its mounting screws and pull it free along with its bracket. Install the new WH13X10029 assembly in the same position, reconnect all three outlet hoses to their original positions, reconnect the electrical connectors, and secure the mounting screws. Reattach the hot and cold supply hoses, tightening securely. Reinstall the top panel, restore the water supply, and check every connection for leaks before restoring power. Run a full test cycle across a few different temperature settings, including a cold-only rinse if your washer has one, to confirm each solenoid is filling and shutting off correctly. If this is a stackable unit, carefully reposition the dryer back on top once testing is complete. Tools needed: Phillips screwdriver, pliers, towel, work gloves, and a helper for stackable units. Frequently Asked Questions My washer won't shut off and keeps filling. Is that this valve? Yes, this is one of the most common symptoms of a failing valve on this platform. A worn internal seal on one of the three solenoids can fail to close fully, letting water continue flowing even after the correct fill level is reached. Since this could lead to overflow, it's worth shutting off the water supply at the wall if you notice this happening rather than waiting to address it. Only my cold-only rinse doesn't fill, but regular wash cycles work fine. Do I need the whole valve? Yes. This valve houses three separate solenoids in one assembly — two that combine for wash-cycle fills at different temperatures, and one dedicated specifically to the cold-only rinse. If just one of those three has failed, the others can continue working normally, which is exactly why a single-cycle fill problem can appear alongside otherwise normal operation. The three solenoids aren't sold or serviced individually, so replacing the complete assembly is the correct repair even if only one function is affected. Do I really need to remove the dryer if this is a stacked unit? On most stacked laundry centers, yes — the top panel of the washer sits underneath the dryer, so the dryer needs to come off first to get access. This is a heavier, more awkward step than the rest of the repair, so it's worth having a second person help lift and support the dryer safely rather than attempting it alone. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It includes the same 3-solenoid design, flow rate, and mounting configuration as the water valve originally installed in your front-load washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11168740 Washer Genuine OEM Cold Water Inlet Valve The W11168740 is a genuine Whirlpool OEM cold water inlet valve for Whirlpool top-load washers, and also fits select Kenmore, Maytag, KitchenAid, Amana, and related models. Located at the rear of the washer, this valve connects to the cold water supply and solenoid wiring, opening to admit cold water into the tub as the cycle calls for it and closing once the correct fill level is reached. Blue in color, with two solenoids, a standard hose fitting inlet, and a single water outlet. Common causes of failure include a worn internal seal that no longer closes fully, or general electrical wear in the solenoid. Symptoms of a failing valve include the washer not getting any cold water, filling slowly, not filling at all, or continuing to fill or leak water even after the washer has been unplugged. It directly replaces WPW10240949, W10240949, 33390069, W10921514, AP6285450, AWP43125, EAP12348073, PD00038781, PS12348073. Quick Answer The W11168740 Washer Genuine OEM Cold Water Inlet Valve fixes Whirlpool, Kenmore, Maytag, KitchenAid, and Amana top-load washers that aren't getting cold water, are filling slowly, aren't filling at all, or keep leaking or filling even when unplugged. Blue, two solenoids. Replaces WPW10240949, W10240949, 33390069, W10921514, AP6285450, AWP43125, EAP12348073, PD00038781, PS12348073. If water keeps running even after the washer is unplugged, try shutting off the cold water supply valve — if that stops it, the cold water inlet valve isn't closing properly and needs replacing. Common Problems This Part Fixes Washer not getting any cold water Washer filling slowly Washer not filling at all Water continuing to fill or leak even after the washer is unplugged Cycle stalling at the fill step and never advancing to wash Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer cold water inlet valve directly replaces the following OEM and cross-reference part numbers: W11168740, WPW10240949, W10240949, 33390069, W10921514, AP6285450, AWP43125, EAP12348073, PD00038781, PS12348073 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cold water inlet valve is compatible with select Whirlpool top-load washers, and also fits select Kenmore, Maytag, KitchenAid, and Amana washers built on the Whirlpool platform. Note: This is the cold water valve only — a separate hot water valve is used alongside it on the same washer. If your washer isn't getting hot water rather than cold, you likely need the companion hot water valve instead. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which valve your washer needs. Key Features Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate Regulates cold water flow into the washer tub during fill Resolves "no cold water," "fills slowly," "won't fill," and "leaks or fills when unplugged" symptoms Blue color with two solenoids Standard hose fitting inlet, single water outlet Direct drop-in replacement — matches the original mounting and hose connections Replaces WPW10240949, W10240949, 33390069, W10921514, AP6285450, AWP43125, EAP12348073, PD00038781, PS12348073 Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, and Amana top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance DIY-friendly repair, typically 20 to 30 minutes Product Specifications Part Number W11168740 Part Type Washer Cold Water Inlet Valve Condition Genuine OEM Brand Whirlpool Location Rear of the appliance Color Blue Solenoids 2 Inlet Standard hose fitting Outlet 1 Repair Difficulty Easy — 20 to 30 minutes Quantity 1 valve (sold individually) Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Access is at the rear of the washer, where both the cold and hot water inlet valves are typically mounted together, each secured with just a few screws. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical clamps and the water hose from the old cold water valve, remove the mounting screws, and pull it free. Install the new W11168740 in the same position, reconnect the water hose and electrical clamps fully, and secure the mounting screws. While you're in this area, consider replacing the fill hose at the same time if it shows signs of wear, since it's easy to access during this same repair. Restore the water supply and power, then run a full test cycle to confirm correct fill behavior with no leaking. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions Water keeps running even after I unplug my washer. Is this the valve I need? Yes, this is a documented symptom of a cold water inlet valve that's no longer closing properly. One customer had exactly this experience — after unplugging the washer, water continued to run, and shutting off the cold water supply valve at the wall stopped it. That confirmed the cold water inlet valve itself wasn't sealing shut, even with no power to the washer, and replacing it resolved the issue. Should I replace the hot water valve at the same time? It's worth considering, especially if both valves are the same age. Several customers have replaced both the hot and cold valves together in a single repair, since they're mounted in the same area and access is already open — one customer described it as "very quick & easy" to do both at once. Is this a difficult repair? No, this is a straightforward repair. Multiple customers describe it as easy, typically secured with just a few screws and simple electrical clamp connections — one review specifically noted the whole job took about 20 minutes. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the cold water inlet valve originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WPW10212596 Washer Genuine OEM Water Valve Description: This Whirlpool valve is an OEM replacement part responsible for regulating and controlling the flow of cold water into the washing machine. This part is located at the rear of the washing machine and is connected to the cold water supply line. It opens and closes to allow the cold water to enter the washer when needed, such as during the initial filling of the machine or when rinsing clothes with cold water. Replaces Part Numbers:WPW10212596, W10212596, 1551647, AP6017174, PS11750469, WPW10212596VP.     California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

W11220230 Washer Genuine OEM Water Valve – Compatible with Whirlpool, Maytag, Amana, Crosley, Roper Washers Product Description Keep your washer filling properly with the W11220230 Washer Genuine OEM Water Valve. This factory-approved valve regulates hot and cold water flow into the tub during wash cycles. A faulty valve can cause filling issues, leaks, or error codes. Replacing it with this genuine OEM part ensures dependable performance and efficient cleaning. Replaces Part Numbers W11220230, W10853296, 4591408, W10632527, W10758829, W11096268, PD00042661, EAP12349461, AP6329544, PS12349461. Compatibility This water valve is compatible with select Whirlpool, Maytag, Amana, Crosley, and Roper washers. Example compatible models include (but are not limited to): Whirlpool WTW5000DW3, Maytag MVWC465HW2, and Amana NTW4516FW3. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Genuine OEM Part – Designed for Whirlpool, Maytag, Amana, Crosley, and Roper washers 💧 Reliable Water Control – Ensures accurate water flow and filling cycles 💰 Cost-Effective OEM Repair – Long-lasting factory-tested replacement 🛠️ DIY Friendly – Installs in 20–30 minutes with basic tools 🛡️ Fixes Common Issues – Resolves filling problems, leaks, and error codes 📐 Product Specification Part Number: W11220230 Component Type: Washer Water Inlet Valve Material: Reinforced plastic body with solenoid valves Mounting: Direct-fit replacement Operating Conditions: Designed for residential washer use Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, pliers, adjustable wrench ⚠️ Safety First: Unplug washer and turn off water supply before beginning repairs. Steps: Disconnect washer from power and water supply. Remove back panel to access the water valve. Disconnect hoses and wiring harness from the old valve. Unscrew and remove the defective valve. Install the new W11220230 valve, reconnect hoses and wiring. Reassemble panel, restore water and power, and run a test cycle. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Fix washer filling issues today — Add to Cart Now for a safe, factory-approved repair!

Read more less

Genuine OEM WPW10140917 Washer Water Inlet Valve with Vacuum Break The Genuine OEM Whirlpool WPW10140917 is the water inlet valve with vacuum break for select Whirlpool-built washers, including Maytag, Kenmore, Amana, Inglis and other brands. The valve regulates water intake for wash cycles and delivers water into the washer drum, and the vacuum break helps keep wash water from backing up into the supply. When the valve fails, the washer may leak, and fill problems can follow. This is the original Whirlpool part, not an aftermarket equivalent. Check your model number before ordering. Quick Answer The Genuine OEM WPW10140917 Water Inlet Valve replaces the water inlet valve on a compatible Whirlpool-built washer when it leaks or no longer controls water intake correctly. Replaces W10140917. Classic symptom: water leaking at the valve. Common Problems This Part Fixes Water leaking at the inlet valve Water inlet valve not controlling water intake correctly Washer not filling or filling incorrectly because of a failed valve Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This water inlet valve replaces or supersedes the following part numbers: WPW10140917, W10140917, OEM18047055, AP6015682, AWP49689, EAP11748963, PD00003949, PS11748963 Whirlpool sells similar valves under nearby numbers, such as WPW10140918, which are not interchangeable by number alone. If your old valve shows a different number, contact our support team and we'll check whether it matches. Compatibility This water inlet valve is listed for Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Inglis, Jenn-Air, Magic Chef and Crosley washers, including these examples: WTW5100VQ1, WTW5100VQ2, WTW5300SQ2, 1CWTW5100VQ1 CAWS9234VQ0, ETW4400VQ3, NTW4500VQ1 ITW4300SQ3, IV45001, IV4500X0 Note: The models above are a small sample, not a full list. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool part, not an aftermarket equivalent Water inlet valve with vacuum break Regulates water intake and delivers water into the washer drum Sold as one complete valve Product Specifications Part Number WPW10140917 OEM Part Number WPW10140917 Part Type Washer Water Inlet Valve with Vacuum Break Condition Genuine OEM Manufacturer Whirlpool Application Select Whirlpool-Built Washers Installation Notes ⚠️ Unplug Power And Shut Off Water Before Installing Unplug the washer and turn off the water supply before you begin, and wear protective gloves. Access to the valve is typically through the back panel or the control panel, depending on the model. Note where each hose and wiring connector goes, disconnect them, remove the old valve, and fit the new valve in the same position. Reconnect everything, restore water and power, and run a short cycle while checking for leaks. Frequently Asked Questions My washer is leaking at the valve. Is this the part I need? If the leak is coming from the water inlet valve itself, replacing the valve is the repair. Check the supply hoses and their connections first, since a loose or worn hose can leak in the same area. Is this an OEM or aftermarket part? This is a genuine OEM part from Whirlpool, not an aftermarket equivalent. Can I use a valve with a similar part number? Not by number alone. Whirlpool sells several water inlet valves with similar numbers for different washers. Match the part number and your model number, or contact our support team and we'll check for you. Will this fit my washer? It is listed for many Whirlpool-built washers, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

ADQ72910908 Refrigerator Water Filter Description: This water filter is designed to remove impurities from the water and ice dispensed by your refrigerator, providing clean and fresh-tasting water. It effectively reduces contaminants such as chlorine, lead, mercury, and other particulates, ensuring safe drinking water for you and your family.  You should replace this water filter if it becomes clogged or reaches the end of its usable life, typically every six months. Causes of a bad water filter can include normal usage leading to clogging, the accumulation of sediments and impurities over time, or damage to the filter casing. Failing to replace the filter regularly can also compromise its effectiveness. Cross Reference Number: ADQ72910908, AP6889635, PS12724753, LT500P/PC/PCS

Read more less

5220FR2075LCM Washer Water Valve Three solenoid valve for cold water. Fits LG front load washers. Replaces Part Numbers: 5221ER1003A, 1268130, 5221ER1003C, 5221ER1003D, 5221ER1003F, AH3527452, EA3527452, AP4442608, PS3527452. 5220FR2075L, 4322702, AGM73269503, AP5986564, PS11728995. Description: This Water Inlet Valve Assembly is a replacement part for specific Kenmore, LG washing machine models. This critical component regulates the flow of water into the washing machine tub, ensuring the proper water supply for various wash cycles and functions.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

WH23X29553 Genuine OEM GE Washer Water Valve The WH23X29553 is a genuine GE OEM water inlet valve for GE front-load washers, and also fits select Hotpoint, RCA, Haier, Monogram, and Café models. This valve controls the flow of water into the washer from the household supply line — when the control calls for a fill, the valve's solenoid opens to admit water, and closes again once the correct level is reached. Built with an ABS plastic body and stainless steel components for durability against corrosion. Common failure causes include mineral or sediment buildup inside the valve body, a burned-out internal solenoid coil, and general wear over years of use. A failing valve typically shows up as the washer not filling properly, filling too slowly, or leaking water. It directly replaces WH23X29553, 33090202, C-491/20-A13, AGE26162, AP6983554, EAP12743643, PD00067381, PS12743643. Quick Answer The WH23X29553 Genuine OEM GE Washer Water Valve fixes GE front-load washers (and select Hotpoint, RCA, Haier, Monogram, and Café models) that aren't filling properly, are filling too slowly, or are leaking water near the valve connections. Replaces WH23X29553, 33090202, C-491/20-A13, AGE26162, AP6983554, EAP12743643, PD00067381, PS12743643. Not the same part as the similarly-numbered WH23X29538 valve — confirm you have the correct number before ordering. Common Problems This Part Fixes Washer not filling with water, or filling only partially Washer fills much more slowly than it used to Water leaking near the valve connections Cycle stalling at the fill step and never advancing to wash No hot water reaching the tub, or no cold water reaching the tub Washer not washing properly due to insufficient or incorrect-temperature water Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: WH23X29553, 33090202, C-491/20-A13, AGE26162, AP6983554, EAP12743643, PD00067381, PS12743643 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select GE front-load washers, and also fits select Hotpoint, RCA, Haier, Monogram, and Café washers built on the GE platform., including model numbers such as: GFW650SPN0SN, GFW650SPN1SN, GFW650SPN2SN, GFW650SPN3SN, GFW650SPN4SN GFW650SSN0WW, GFW650SSN1WW, GFW650SSN2WW, GFW650SSN3WW, GFW650SSN4WW GFW850SPN0DG, GFW850SPN0RS, GFW850SPN1DG, GFW850SPN1RS, GFW850SPN2DG, GFW850SPN2RS, GFW850SPN3DG, GFW850SPN3RS, GFW850SPN4RS, GFW850SPN5RS GFW850SSN0WW, GFW850SSN1WW, GFW850SSN2WW, GFW850SSN3WW GFW655SSV0WW PFW870SPV0RS PFW950SPT0DS, PFW950SPT1DS, PFW950SPT2DS Note — not the same as WH23X29538: A similarly-numbered valve, WH23X29538, is a separate part (replaces 4977241, AP6990115, PS16217225, EAP16217225, 33090201, 0024000126GB) used on related but distinct models. The two are easy to confuse given how close the numbers are — always confirm you have the exact part number from your appliance or parts diagram before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified solenoid design and flow rate ABS plastic body with stainless steel components for corrosion resistance Resolves "won't fill," "fills slowly," and "leaking near the valve" symptoms caused by valve failure Direct drop-in replacement — matches the original mounting and hose connections Replaces AP6983554, PS12743643, EAP12743643, 33090202, and 0024000126GA Compatible with GE, Hotpoint, RCA, Haier, Monogram, and Café front-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WH23X29553 Part Type Washer Water Inlet Valve Condition Genuine OEM Brand GE Application Front-Load Washers Body Material ABS plastic Component Material Stainless steel Quantity 1 valve Compatible Brands GE, Hotpoint, RCA, Haier, Monogram, Café Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Release The Control Panel Carefully Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Access to this valve is typically behind the front control panel on many models. When removing the front control panel, avoid pulling it straight out too far — slotted tabs on the right side of the panel can break if forced. Instead, pull the panel gently forward, then slide it to the right to release it cleanly. With the panel released, locate the valve and disconnect the hot and cold water supply hoses, keeping a towel handy for residual water. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the outlet hoses from the old valve, remove its mounting screws, and pull it free. Install the new WH23X29553 in the same position, reconnect all outlet hoses to their original positions, reconnect the electrical connector, and secure the mounting screws. Reattach the hot and cold supply hoses, tightening securely. Reinstall the control panel and any surrounding trim, restore the water supply, and check every connection for leaks before restoring power. Run a full test cycle across a few different temperature settings to confirm each fill function works correctly. Tools needed: Phillips screwdriver, pliers, towel, work gloves. Frequently Asked Questions How do I remove the front control panel without breaking it? Avoid pulling the panel straight out with heavy force — the slotted tabs on the right side of the panel can snap if you pull too far. Instead, pull the panel gently forward first, then slide it to the right to release it from its mounting. This gentler approach avoids the most common way this panel gets damaged during a valve repair. I've heard this valve sometimes needs replacing again after just a couple of years. Is that normal? Some owners have reported needing to replace this valve again within a relatively short time, even after a successful repair. While most installations hold up well long-term, if you experience a repeat failure, it's worth double-checking your household water pressure and mineral content, since hard water and high pressure can accelerate wear on any water valve regardless of brand. Is this the same as WH23X29538? The numbers look almost identical. No, these are two separate GE valve part numbers with different cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close match, since ordering the wrong one means it won't fit correctly. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water valve originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH13X26637 Genuine OEM GE Washer Water Inlet Valve The WH13X26637 is a Genuine OEM GE replacement quad water inlet valve assembly compatible with select GE and GE Profile top-load washers in the GTW, GTV, GTN, PTW, and related series. This is a quad (4-solenoid) valve assembly that controls the flow of hot water, cold water, bleach dispenser water, and fabric softener dispenser water from the household supply lines into the washer tub and dispenser compartments. Each solenoid port is independently controlled by the washer's control board. When any port fails, the washer may not fill, fill too slowly, fill with the wrong temperature, overfill, fail to dispense bleach or fabric softener, or drip water between cycles. As a Genuine OEM part manufactured by GE to factory specifications, the WH13X26637 is a direct current-production replacement for the earlier WH13X24058. It measures approximately 7"L x 3"W x 3"H with multi-colored ports (blue, green, red, tan, silver, and gold) for easy identification of each solenoid's function. It directly replaces WH13X24058, WH13X26637-25PK, 4546358, AP6282070, EAP12171559, PD00037665, and PS12171559. Installs in 20–30 minutes with basic hand tools. Quick Answer The WH13X26637 Genuine OEM GE Washer Water Inlet Valve fixes GE top-load washers that won't fill, fill slowly, fill with wrong temperature, won't dispense bleach or fabric softener, overfill, or drip water between cycles. Quad (4-solenoid) valve. Approx. 7"L x 3"W x 3"H. Multi-color port identification. Genuine OEM. Replaces WH13X24058, WH13X26637-25PK, 4546358, AP6282070, EAP12171559, PS12171559. Compatible with GE GTW, GTV, GTN, PTW series top-load washers. Common Problems This Part Fixes Washer not filling with water at all when a cycle is started Washer filling very slowly — one or more solenoid ports partially blocked or failing Washer filling with only cold or only hot water — one temperature solenoid has failed Washer overfilling or filling continuously — valve port stuck open Bleach not dispensing during the wash cycle Fabric softener not dispensing at the rinse cycle point Water dripping into the tub between cycles — valve port not sealing completely Water leaking from the back of the washer near the valve body Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: WH13X26637, WH13X24058, AGE26282, AP6282070, EAP12171559, PD00037665, PS12171559. WH13X26637 is the current updated part number superseding WH13X24058. If your washer's parts diagram shows WH13X24058, the WH13X26637 is the correct current replacement. Contact our support team with your model number if you need confirmation before ordering. Compatibility This water inlet valve is compatible with select GE and GE Profile top-load washers from the following series: GE washers — GTW680 series (GTW680BPL0DG, GTW680BPL1DG, GTW680BPL2DG, GTW680BSJ0WS, GTW680BSJ1WS, GTW680BSJ3WS, GTW680BSJ4WS, GTW680BSJ5WS, GTW680BSJ6WS and related models) GE washers — GTW685 series (GTW685BPL0DG, GTW685BPL1DG, GTW685BSL1WS, GTV685BSL0WS and related models) GE washers — GTW720 series (GTW720BPN0DG, GTW720BSN0WS and related models) GE washers — GTW725 series (GTW725BPN0DG, GTW725BSN0WS and related models) GE washers — GTW750 series (GTW750CPL0DG, GTW750CPL1DG, GTW750CSL0DG, GTW750CSL0WS, GTW750CSL1WS and related models) GE washers — GTW755 series (GTW755CPM0DG, GTW755CSM0WS, GTW755CSM1WS and related models) GE Profile washers — PTW600, PTW605, PTW700, PTW705 series and related models GE washers — GTN755 series (GTN755CPM1DG and related models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Quad (4-solenoid) valve assembly — independently controls hot water, cold water, bleach dispenser, and fabric softener dispenser ports Multi-colored ports for easy solenoid identification during installation Dimensions: approximately 7"L x 3"W x 3"H Current updated part number — directly supersedes WH13X24058 Compatible with GE GTW680, GTW685, GTW720, GTW725, GTW750, GTW755, PTW600, PTW605, PTW700, PTW705, GTN755 series top-load washers DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WH13X26637 Supersedes WH13X24058 Part Type Washer Water Inlet Valve Assembly (Quad / 4-Solenoid) Condition Genuine OEM Application GE and GE Profile Top-Load Washers Solenoids 4 (hot, cold, bleach, fabric softener) Dimensions Approximately 7"L x 3"W x 3"H Port Colors Multi-color (blue, green, red, tan, silver, gold) Material Plastic / Metal Compatible Brands GE, GE Profile Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off both the hot and cold water supply valves before beginning. Pull the washer away from the wall to access the back panel and remove it to expose the valve assembly. Photograph all wire harness connections and hose routing — the multi-color ports make this straightforward. Disconnect the two external supply hoses from the hot and cold inlet ports. Disconnect the internal outlet hoses by releasing the retaining clips. Disconnect the wire harness connectors from each solenoid terminal. Unscrew the mounting bolts and remove the old valve. Install the new WH13X26637 valve in the same position, reconnect all hoses and wire harnesses in the documented positions, and secure the mounting bolts. Reconnect the external supply hoses, restore water supply and power, and run a fill cycle to verify normal filling and check for leaks. Tools needed: Phillips screwdriver, socket wrench, needle-nose pliers. Frequently Asked Questions What is the difference between WH13X26637 and WH13X24058? These are the same quad water inlet valve assembly — WH13X26637 is the current updated part number that GE issued to supersede the earlier WH13X24058. If your washer's documentation, parts diagram, or old valve label shows WH13X24058, the WH13X26637 is the correct current replacement to order. Both are quad (4-solenoid) valve assemblies with the same port configuration and function. What does each solenoid port on this quad valve control? The WH13X26637 quad valve has four independently operated solenoid ports. The hot water port opens to supply hot water from the household supply line. The cold water port supplies cold water. The bleach dispenser port delivers cold water through the bleach compartment at the appropriate point in the wash cycle. The fabric softener port delivers water through the softener compartment during the rinse cycle. When any single solenoid fails, only the function it controls is affected — the rest of the valve continues to work normally. My washer won't fill and shows an error code — is it the water inlet valve? A fill error code on compatible GE models commonly points to the water inlet valve. Before replacing the valve, confirm that both supply valves behind the washer are fully open, neither supply hose is kinked, and the household water pressure is adequate. You can test each solenoid coil with a multimeter — a working coil shows resistance (typically 200–500 ohms); an open circuit confirms that coil has failed and the valve needs replacement. If all coils test good but the washer still won't fill, the issue may be with the control board or water pressure. My washer fills fine but won't dispense fabric softener — could it be the valve? Yes — if only the fabric softener dispenser function is affected, the solenoid coil controlling that specific port has likely failed. Since it is part of the same quad valve assembly, replacing the entire WH13X26637 assembly resolves the failed port. Individual solenoid ports cannot be replaced — the complete quad valve assembly must be replaced when any port fails. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same quad water inlet valve assembly installed in compatible GE and GE Profile top-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

10023852 Genuine OEM Bosch Dishwasher Water Valve The 10023852 is a genuine Bosch OEM warm water inlet valve for Bosch, Thermador, Dacor, and Gaggenau dishwashers. This valve regulates the flow of warm water into the dishwasher during each wash cycle — a solenoid opens when the dishwasher calls for water and closes once the required amount has been reached, which is what prevents overfilling or underfilling and supports thorough cleaning performance. Rated 110-127V, 60Hz. Common causes of a bad valve range from mineral buildup due to hard water, which can obstruct the valve, to general mechanical wear and electrical problems that impair the valve's ability to open or close correctly. Symptoms of a failing valve include inadequate water filling the dishwasher, overfilling that can lead to leaks and water damage, unusual noises coming from the valve area, or the dishwasher failing to start. It directly replaces 00628334, 3278459, 33199023, 628334, 9000655808, ABS12394, AP5691117, AP7193108, EAP8729241, PD00075605, PS8729241. Quick Answer The 10023852 Genuine OEM Bosch Dishwasher Water Valve fixes Bosch, Thermador, Dacor, and Gaggenau dishwashers with inadequate water filling, overfilling, unusual noise near the valve, or a dishwasher that won't start. 110-127V, 60Hz. Replaces 00628334, 3278459, 33199023, 628334, 9000655808, ABS12394, AP5691117, AP7193108, EAP8729241, PD00075605, PS8729241. If you're also seeing a slow leak near the sump area, be aware that on some Bosch models the sump gasket is built into the sump itself rather than sold as a separate part — a leak there is a different repair from this valve. Common Problems This Part Fixes Inadequate water filling the dishwasher Overfilling, which can lead to leaks and water damage Unusual noises coming from the valve area Dishwasher failing to start Poor washing results due to insufficient water supply Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers: 10023852, 00628334, 3278459, 33199023, 628334, 9000655808, ABS12394, AP5691117, AP7193108, EAP8729241, PD00075605, PS8729241. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select Bosch dishwashers, and also fits select Thermador, Dacor, and Gaggenau dishwashers built on the Bosch platform, including model numbers such as SHXM98W75N/01, SHX863WD5N/01, SHEM63W55N/01, and SHPM65Z55N/01, and spanning model series SHE, DWH, SHX, SHV, and SHP. Note: This valve is not universal — it's designed for specific Bosch, Thermador, Dacor, and Gaggenau models. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Bosch OEM part — factory-specified solenoid design and flow rate Regulates warm water flow into the dishwasher during each wash cycle Resolves "won't fill properly," "overfilling," "unusual noise," and "won't start" symptoms caused by valve failure Direct drop-in replacement — matches the original mounting and connections Replaces 00628334, 3278459, 33199023, 628334, 9000655808, ABS12394, AP5691117, AP7193108, EAP8729241, PD00075605, PS8729241 Compatible with Bosch, Thermador, Dacor, and Gaggenau dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 10023852 Part Type Dishwasher Warm Water Inlet Valve Condition Genuine OEM Brand Bosch Voltage 110-127V Frequency 60 Hz Function Regulates warm water flow into the dishwasher during fill Repair Difficulty Easy to Moderate Quantity 1 valve Compatible Brands Bosch, Thermador, Dacor, Gaggenau Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. On many Bosch models, pulling the dishwasher out from under the counter gives the best access to the valve and surrounding sump area. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and water line from the old valve, remove its mounting hardware, and pull it free. Install the new 10023852 in the same position, reconnect the water line and electrical connector fully, and secure the mounting hardware. If you're troubleshooting a slow leak in this general area rather than a fill problem, be aware that on some Bosch models the sump gasket is built directly into the sump itself and isn't sold as a separate part — a leak there is a different repair involving the sump assembly (diverter, circulation pump, drain pump, and aqua-sensor) rather than this valve. Restore the water supply and power, then run a test cycle to confirm the dishwasher fills correctly with no leaks. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions My dishwasher isn't filling with enough water. Is this the right part? Yes, this is one of the most direct symptoms of a failed water inlet valve. Since this valve is what admits warm water from your household supply into the dishwasher, mineral buildup, mechanical wear, or an electrical fault can prevent it from opening fully, leaving the dishwasher without enough water for a proper wash. I have a slow leak near the bottom of my dishwasher. Is that this valve too? Not necessarily. One customer traced a slow, worsening leak on a Bosch dishwasher to the sump gasket, not the water valve — and found that on their model, the gasket is built into the sump itself rather than being a separately replaceable part, requiring a more involved repair pulling the sump apart to address it. If your leak is coming specifically from the sump area rather than showing up as a fill problem, it may be a different repair than this valve replacement. What causes this valve to fail over time? The most common cause is mineral buildup from hard water, which can gradually obstruct the valve's internal passages. Mechanical wear and general electrical problems can also affect the valve's ability to open and close correctly over years of use. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Bosch to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11168740 Washer Water Valve (Cold Side) The XPARTCO W11168740 is an aftermarket replacement cold water inlet valve for Whirlpool-built top-load washers, located on the top back of the cabinet where the hot and cold supply hoses connect. Unlike its companion hot-side valve (sold separately as W11168743, a single-solenoid design), this cold valve uses two internal solenoid coils in one blue-bodied housing. When the control calls for a cold fill, it energizes the appropriate solenoid to open the water path; once the correct level is reached, it closes again. Because it's a dedicated cold-only valve, a failure here produces a distinctive symptom: cold-only fills stop working, slow down dramatically, or don't stop when they should, while hot fills (governed by the separate hot valve) continue working independently. Rated 120V, 60Hz, with push-on outlet connections sealed by rubber grommets. Common failure causes include mineral or sediment buildup that prevents the valve from sealing, a burned-out solenoid coil, or a worn seal at the outlet connection. It directly replaces WPW10240949, W10240949, W10921514, 33390069, 4546379, AP6285450, PD00038781, and PS12348073. Quick Answer The XPARTCO W11168740 Washer Water Valve (Cold Side) fixes Whirlpool-built top-load washers where cold water won't fill, fills slowly, keeps filling and won't stop, leaks, or throws a fill-related error code — while hot water fills normally. Blue-bodied, 2-solenoid cold-only valve, 120V, 60Hz, push-on outlet with rubber grommets. Replaces WPW10240949, W10240949, W10921514, 33390069, 4546379, AP6285450, PD00038781, PS12348073. This is the cold-side valve only — the companion hot-side valve is sold separately as W11168743. Common Problems This Part Fixes Washer won't fill with cold water while hot water fills normally Cold water fills much more slowly than it used to Washer keeps filling with cold water and won't stop, leading to overfill Water leaking at the cold connection point Fill-related error code displayed on the control panel Cycle stalling at the fill step and never advancing to wash Cold wash or cold rinse cycles specifically affected while other cycles run fine Water pooling underneath or behind the washer near the cold supply connection Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer cold water inlet valve directly replaces the following OEM and cross-reference part numbers: W11168740, WPW10240949, W10240949, W10921514, 33390069, 4546379, AP6285450, AWP43125, EAP12348073, PD00038781, PS12348073 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cold water inlet valve is compatible with select Whirlpool-built top-load washers across the Whirlpool family of brands, including: Whirlpool top-load washers — WTW series Maytag top-load washers (select Whirlpool-built models) Select Kenmore top-load washers built on the Whirlpool platform Verified model numbers include: WTW5500XL0, WTW5500XL2, and WTW5640XW3. Note — cold side only: This is the cold water valve, identifiable by its blue body and two internal solenoids. The matching hot water valve for these same washers is sold separately under part number W11168743 — a single-solenoid design. The two are not interchangeable. If both valves need replacement, order both part numbers. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement dedicated cold water inlet valve for Whirlpool-built top-load washers Two internal solenoid coils in one blue-bodied housing, identifiable at a glance from the single-solenoid hot valve Resolves "won't fill with cold water," "fills slowly," "won't stop filling," and "leaking at the connection" symptoms caused by valve failure Rated 120V, 60Hz Push-on outlet connections sealed with rubber grommets Approximately 3-3/8"L x 3-1/2"W x 2-3/8"H Direct drop-in replacement — no modification required Replaces WPW10240949, W10240949, W10921514, 33390069, 4546379, AP6285450, PD00038781, and PS12348073 Compatible with a wide range of Whirlpool, Maytag, and Kenmore top-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPW11168740 OEM Part Number W11168740 Part Type Washer Water Inlet Valve — Cold Side Condition Aftermarket Replacement Application Top-Load Washers (Whirlpool-Built) Voltage 120V Frequency 60 Hz Solenoids 2 (dedicated cold water function) Color Blue / Teal / Black Material Plastic and metal Outlet Connection Push-on with rubber grommets Dimensions Approx. 3-3/8"L x 3-1/2"W x 2-3/8"H Companion Part W11168743 (hot water valve, sold separately) Quantity 1 valve Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Have A Towel Ready Unplug the washer or shut off its circuit breaker, and shut off both the hot and cold water supply valves before beginning. Wear work gloves. Disconnect the cold water supply hose from the back of the valve first — have a towel or shallow pan ready, since residual water will spill out. Remove the screws securing the top panel (a 1/4" nut driver or socket handles most models), then slide the panel back and lift it off to access the valve assembly from inside the cabinet. Photograph the wiring connections before disconnecting anything, since the hot and cold valves sit next to each other and it's easy to cross a wire. Disconnect the electrical connector(s) from the old cold valve, disconnect the push-on outlet hose (check the rubber grommet for wear and replace it if it looks flattened or cracked), remove the two mounting screws holding the valve, and pull it free — leave the hot valve (W11168743) undisturbed if it isn't also being replaced. Install the new W11168740 in the same position, secure the mounting screws, reconnect the electrical connector(s), and press the outlet hose back onto its fitting with the grommet properly seated. Reattach the cold water supply hose, tightening securely by hand plus a partial turn with pliers. Reinstall the top panel, restore the water supply, and check every connection you touched for leaks before restoring power. Run a short cycle and confirm cold water fills at the normal rate, and stops when it should, with no leaking underneath or behind the washer. Tools needed: 1/4" nut driver or socket, Phillips screwdriver, pliers, towel or shallow pan, work gloves. Frequently Asked Questions Cold water won't fill but hot water works fine. Is this the right part? Yes — that's exactly the symptom pattern this valve addresses. Since your washer uses separate hot and cold valves rather than one combined valve, a fault on the cold side only affects cold fills while the hot valve keeps working independently. If cold-specific cycles are the ones failing while hot cycles are unaffected, this cold-side valve is the correct part to replace. How can I tell this valve apart from the hot-side valve just by looking at it? This cold valve has a blue body and two internal solenoid coils, while the companion hot-side valve (W11168743) is a single-solenoid design. If you're staring at the old valve trying to confirm which one you're removing, the color and solenoid count are a quick visual check. Do I need to replace both the hot and cold valves at the same time? Not necessarily. Since these are independent single-function valves, you only need to replace the one that has actually failed. If only cold fills are affected, replacing this W11168740 valve alone is sufficient. Some people choose to replace both while the top panel is already off, especially on an older washer, but it isn't required. My washer keeps filling with cold water and won't stop. Is that dangerous? It can lead to overflow and water damage if left unaddressed, so it's worth shutting off the water supply at the wall if this happens rather than waiting. A valve that won't stop filling usually means a worn internal seal is no longer sealing shut when the solenoid de-energizes, letting water continue flowing. This valve is the correct replacement for that symptom. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dual-solenoid design, connection type, and dimensions of the original W11168740 cold water valve used in compatible Whirlpool, Maytag, and Kenmore top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

ADQ73613403 Refrigerator Water Filter Description: This water filter is designed to remove impurities from the water and ice dispensed by your refrigerator, providing clean and fresh-tasting water. It effectively reduces contaminants such as chlorine, lead, mercury, and other particulates, ensuring safe drinking water for you and your family.  You should replace this water filter if it becomes clogged or reaches the end of its usable life, typically every six months. Causes of a bad water filter can include normal usage leading to clogging, the accumulation of sediments and impurities over time, or damage to the filter casing. Failing to replace the filter regularly can also compromise its effectiveness. Cross Reference Number: ADQ73613403, AP6889636, PS12724756, LT800P/PC/PCS

Read more less