Search results for "washer Water Valve"

Genuine OEM WPW10238100 Refrigerator Water Valve The WPW10238100 is a genuine OEM single primary water inlet valve from Whirlpool for Whirlpool-built refrigerators sold under the Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air, Inglis, and Ikea names. The valve is an electrically operated solenoid that opens to let water from the household supply line into the refrigerator's water system, and closes to stop it. When the valve fails, the refrigerator can stop supplying water to the dispenser and ice maker, make little or no ice, leak, or, if it no longer shuts off, overfill the ice maker and build up ice and frost. This is a genuine OEM part, not an aftermarket equivalent, so the fit and operation match the original. It is a simple repair for most owners, typically 15–30 minutes. Some refrigerators also use a separate dual-solenoid valve, so check the Compatibility note before ordering. Quick Answer The Genuine OEM WPW10238100 Water Valve fixes a Whirlpool-built refrigerator with no water at the dispenser, little or no ice, an overflowing ice maker, or a leak caused by a failed water inlet valve. Single primary water inlet valve, genuine OEM from Whirlpool. Classic symptom: the dispenser gives little or no water and the ice maker isn't making ice, even though the water supply is on. Common Problems This Part Fixes Water dispenser not working, or giving only a trickle Ice maker not making ice Ice maker overflowing, with ice or frost buildup Water leaking from the refrigerator Valve making noise or not shutting off properly Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This water valve replaces the following part numbers: WPW10238100, W10238100, W10498992, IMV-8100, K-78199, AP6017532, AWP50143, EAP11750831, PD00002616, PS11750831 These are Whirlpool's un-prefixed and earlier numbers for this valve. If your old valve or parts diagram shows any of them, match against this list. Compatibility This valve is listed for refrigerators from the Whirlpool family of brands: Whirlpool, KitchenAid, Maytag, Jenn-Air, Inglis, and Ikea Kenmore, including models such as 10641162310, 10651132210, and 10651149110 Other models include ISC21CNEDS00, KRSC503ESS00, KSC24C8EYY02, and WRF560SEHZ00 Note: This is a single primary water inlet valve. Some refrigerators use a separate dual-solenoid valve for the ice maker and dispenser, which is a different part. The model list above is only a sample, so confirm fit by matching the number on your old valve or your parts diagram against the Replaces list, or contact our support team with your model number and we'll verify before you order. Key Features Genuine OEM Whirlpool single primary water inlet valve, not an aftermarket equivalent Replaces W10238100 and W10498992 Restores water to the dispenser and ice maker, and proper shut-off Fits select Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air, Inglis, and Ikea refrigerators Simple replacement, typically 15–30 minutes Product Specifications Part Number WPW10238100 OEM Part Number WPW10238100 Part Type Refrigerator Single Primary Water Inlet Valve Condition Genuine OEM Manufacturer Whirlpool Application Select Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air, Inglis & Ikea Refrigerators Installation Notes ⚠️ Shut Off Water and Unplug Power Turn off the water supply to the refrigerator and unplug it before starting. Following your model's service guide, pull the refrigerator out and remove the rear access panel to reach the valve. Disconnect the water lines from the old valve, and the wiring connector from its solenoid, then remove the mounting screws. Install the new valve in the same position, reconnect the wiring and water lines securely, and replace the panel. Restore water and power, check every connection for leaks, and run water through the dispenser for a few minutes to flush the line. The valve needs at least 20 psi of water pressure to shut off properly, so if the ice maker still overflows, check the supply pressure. Frequently Asked Questions My dispenser has no water and the ice maker isn't working. Is this the part I need? It can be. Before replacing the valve, check that the water supply is on, the supply line isn't kinked, and the water filter isn't clogged. If those are fine, a failed water inlet valve is a likely cause. My ice maker is overflowing. Could it be the valve? Yes. A valve that doesn't shut off fully will keep letting water in. Also confirm your water pressure is at least 20 psi, since low pressure can stop the valve from closing properly. My refrigerator has a dual-solenoid valve. Will this work? No. This is a single primary valve, and the dual-solenoid valve is a different part. Check your parts diagram or contact our support team with your model number. Is this an OEM part? Yes. This is a genuine OEM Whirlpool part, not an aftermarket equivalent, so it matches the original factory fit and specification. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DD62-00084A Dishwasher Water Valve – Compatible with Samsung Dishwashers Product Description Restore proper water flow and reliable cleaning performance with the XPARTCO DD62-00084A Dishwasher Water Valve. This Dishwasher Water Valve is an essential component for maintaining the optimal performance of your dishwasher. This replacement part ensures precise water flow control, allowing your dishwasher to operate efficiently and effectively. A faulty water valve can cause no water entering the dishwasher, slow filling, or poor cleaning performance. Replacing it with this dependable XPARTCO valve helps restore consistent water flow and efficient operation. XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and function. Replaces Part Numbers DD62-00084A, 2692215, ASM36078, EAP4222448, PD00002158, 737534554937, OEM15534663, AP5178218, PS4222448 Compatibility This replacement dishwasher water inlet valve fits select Samsung dishwashers. Common compatible models include (but are not limited to): Samsung DW80F600UTS Samsung DW80J3020US Always verify your dishwasher’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and water flow performance 💧 Accurate Water Fill Control – Ensures proper water levels for effective cleaning ⚙️ Fixes Common Issues – Resolves no-fill or slow-fill problems 💪 Durable Solenoid Valve – Designed for reliable long-term use 💰 Cost-Effective Repair – Affordable alternative to OEM valves ⚠️ Symptoms If your dishwasher is experiencing any of the following issues, this part may need replacement: ❌ Dishwasher not filling with water 💧 Slow or weak water flow ⚠️ Poor cleaning performance due to low water level 🔄 Cycle not starting properly 🚫 No water entering during wash cycle Replacing this water valve can restore proper dishwasher operation and cleaning efficiency. 📐 Product Specification Part Number: XPDD62-00084A Component Type: Dishwasher Water Inlet Valve Voltage: 120V AC Application: Dishwasher water supply system Mounting: Screw-mounted with hose connection Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, adjustable wrench ⚠️ Safety First: Disconnect power and shut off the water supply before servicing the dishwasher. Basic Steps: Turn off power and water supply. Remove the lower access panel. Disconnect water supply line and electrical connector. Remove mounting screws and remove the old valve. Install the new XPARTCO DD62-00084A valve. Reconnect water line and wiring. Restore power and water, then test for leaks and proper filling. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore reliable dishwasher performance — Add to Cart Now for a dependable repair!

Read more less

XPARTCO W10238100 Refrigerator Water Valve The XPARTCO W10238100 is an aftermarket replacement single primary water inlet valve for Whirlpool-built refrigerators sold under the Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air, Inglis, and Ikea names. The valve is an electrically operated solenoid that opens to let water from the household supply line into the refrigerator's water system, and closes to stop it. When the valve fails, the refrigerator can stop supplying water to the dispenser and ice maker, make little or no ice, leak, or, if it no longer shuts off, overfill the ice maker and build up ice and frost. This valve is a direct replacement for the OEM W10238100 / WPW10238100 and is a simple repair for most owners, typically 15–30 minutes. Some refrigerators also use a separate dual-solenoid valve, so check the Compatibility note before ordering. Quick Answer The XPARTCO W10238100 Water Valve fixes a Whirlpool-built refrigerator with no water at the dispenser, little or no ice, an overflowing ice maker, or a leak caused by a failed water inlet valve. Single primary water inlet valve, aftermarket replacement for W10238100 and WPW10238100. Classic symptom: the dispenser gives little or no water and the ice maker isn't making ice, even though the water supply is on. Common Problems This Part Fixes Water dispenser not working, or giving only a trickle Ice maker not making ice Ice maker overflowing, with ice or frost buildup Water leaking from the refrigerator Valve making noise or not shutting off properly Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This water valve replaces the following part numbers: WPW10238100, W10238100, W10498992, IMV-8100, K-78199, AP6017532, AWP50143, EAP11750831, PD00002616, PS11750831 These are Whirlpool's un-prefixed and earlier numbers for this valve. If your old valve or parts diagram shows any of them, match against this list. Compatibility This valve is listed for refrigerators from the Whirlpool family of brands: Whirlpool, KitchenAid, Maytag, Jenn-Air, Inglis, and Ikea Kenmore, including models such as 10641162310, 10651132210, and 10651149110 Other models include ISC21CNEDS00, KRSC503ESS00, KSC24C8EYY02, and WRF560SEHZ00 Note: This is a single primary water inlet valve. Some refrigerators use a separate dual-solenoid valve for the ice maker and dispenser, which is a different part. The model list above is only a sample, so confirm fit by matching the number on your old valve or your parts diagram against the Replaces list, or contact our support team with your model number and we'll verify before you order. Key Features Aftermarket replacement single primary water inlet valve Replaces W10238100, WPW10238100, and W10498992 Restores water to the dispenser and ice maker, and proper shut-off Fits select Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air, Inglis, and Ikea refrigerators Simple replacement, typically 15–30 minutes Product Specifications Part Number XPW10238100 OEM Part Number W10238100, WPW10238100 Part Type Refrigerator Single Primary Water Inlet Valve Condition Aftermarket Replacement Application Select Whirlpool, KitchenAid, Kenmore, Maytag, Jenn-Air, Inglis & Ikea Refrigerators Installation Notes ⚠️ Shut Off Water and Unplug Power Turn off the water supply to the refrigerator and unplug it before starting. Following your model's service guide, pull the refrigerator out and remove the rear access panel to reach the valve. Disconnect the water lines from the old valve, and the wiring connector from its solenoid, then remove the mounting screws. Install the new valve in the same position, reconnect the wiring and water lines securely, and replace the panel. Restore water and power, check every connection for leaks, and run water through the dispenser for a few minutes to flush the line. The valve needs at least 20 psi of water pressure to shut off properly, so if the ice maker still overflows, check the supply pressure. Frequently Asked Questions My dispenser has no water and the ice maker isn't working. Is this the part I need? It can be. Before replacing the valve, check that the water supply is on, the supply line isn't kinked, and the water filter isn't clogged. If those are fine, a failed water inlet valve is a likely cause. My ice maker is overflowing. Could it be the valve? Yes. A valve that doesn't shut off fully will keep letting water in. Also confirm your water pressure is at least 20 psi, since low pressure can stop the valve from closing properly. My refrigerator has a dual-solenoid valve. Will this work? No. This is a single primary valve, and the dual-solenoid valve is a different part. Check your parts diagram or contact our support team with your model number. Is this an OEM part? No. This is an XPARTCO aftermarket replacement built to match the Whirlpool W10238100. If you prefer a genuine OEM valve, contact us. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine Frigidaire OEM Frigidaire 5304533220 Washer Water Fill Hose Assembly Genuine OEM internal valve-to-tub fill hose for select Frigidaire-built laundry centers and washer/dryer combination units. Product Overview The Frigidaire 5304533220 Washer Water Fill Hose Assembly is a Genuine OEM internal fill hose used to route incoming water from the washer water inlet valve to the wash tub on compatible laundry-center models. This is the valve-to-tub hose inside the appliance. It is not the external hot/cold household water-supply hose that connects the appliance to the wall faucets. Quick Answer 5304533220 is the Genuine Frigidaire OEM valve-to-tub washer fill hose. It replaces earlier Frigidaire numbers 5304508358 and 809191901 and is used on select Frigidaire, Kenmore, Crosley, and other Electrolux-manufactured laundry centers. Common Problems This Part May Fix Water leaking inside the washer cabinet during fill Cracked, split, hardened, or deteriorated fill hose Leak between the inlet-valve outlet and wash tub Loose or damaged internal water-fill connection Water dripping from the valve-to-tub hose during operation Replaces and Cross-References 5304533220, 5304508358, 809191901, AFR20016, AP7194866, EAP11775692, PD00076846, PS16745853 Cross-reference numbers are provided for identification. Always verify the full appliance model number before ordering. Compatibility Confirmed applications include select Frigidaire-built laundry centers and washer/dryer combinations such as: FLCE7523AW0 FLCE7523AW1 FLCE7522AW1 FLCE7522AW4 FFLE3900UW0 FFLE3900UW1 FFLG3900UW0 FFLE3911QW1 CFLE3900UW0 41761712511 41761732810 41771732810 Important: This is only a partial compatibility list. Confirm the complete model number from the appliance rating label before purchase. Key Features Genuine Frigidaire OEM replacement part Internal valve-to-tub fill hose Routes fill water from the inlet valve to the washer tub Direct replacement for 5304508358 and 809191901 Factory-style fit for compatible laundry centers Used on select Frigidaire, Kenmore, and related Electrolux-built models Product Specifications Manufacturer Part Number 5304533220 Brand Frigidaire Part Type Washer Internal Water Fill Hose Hose Location Water Inlet Valve to Wash Tub OEM Status Genuine OEM Appliance Type Laundry Center / Washer-Dryer Combo Condition New External Supply Hose? No — this is an internal appliance hose Installation Notes Disconnect electrical power to the appliance before service. Shut off both household water-supply valves. Access the washer inlet-valve and tub-fill connection according to the model-specific service procedure. Place towels or a shallow pan below the hose connections to catch residual water. Release the clamps and remove the old hose without damaging the valve outlet or tub fitting. Install the new hose fully onto both fittings and reinstall the clamps in their original positions. Restore water and inspect carefully for leaks before returning the appliance to service. Diagnostic tip: If water is leaking during fill, inspect the hose, clamps, inlet valve, and tub connection before replacing parts. A leak from the external household supply hose requires a different part. Frequently Asked Questions Is 5304533220 a Genuine OEM part? Yes. It is a Genuine Frigidaire OEM fill hose. Does 5304533220 replace 5304508358? Yes. 5304533220 supersedes 5304508358 and 809191901. Is this the hose that connects the washer to the wall faucet? No. This is an internal valve-to-tub fill hose located inside the laundry center. Can this part correct a washer leak? Yes, if the leak is caused by a cracked or damaged valve-to-tub fill hose or its connection. Inspect all nearby fittings and clamps before ordering. Shop With Confidence Verify your complete laundry-center model number before ordering. This listing is for the Genuine Frigidaire OEM internal valve-to-tub fill hose. Genuine Frigidaire OEMValve-to-Tub Fill HoseCompatibility SupportFast U.S. Shipping

Read more less

10023852 Genuine OEM Bosch Dishwasher Water Valve The 10023852 is a genuine Bosch OEM warm water inlet valve for Bosch, Thermador, Dacor, and Gaggenau dishwashers. This valve regulates the flow of warm water into the dishwasher during each wash cycle — a solenoid opens when the dishwasher calls for water and closes once the required amount has been reached, which is what prevents overfilling or underfilling and supports thorough cleaning performance. Rated 110-127V, 60Hz. Common causes of a bad valve range from mineral buildup due to hard water, which can obstruct the valve, to general mechanical wear and electrical problems that impair the valve's ability to open or close correctly. Symptoms of a failing valve include inadequate water filling the dishwasher, overfilling that can lead to leaks and water damage, unusual noises coming from the valve area, or the dishwasher failing to start. It directly replaces 00628334, 3278459, 33199023, 628334, 9000655808, ABS12394, AP5691117, AP7193108, EAP8729241, PD00075605, PS8729241. Quick Answer The 10023852 Genuine OEM Bosch Dishwasher Water Valve fixes Bosch, Thermador, Dacor, and Gaggenau dishwashers with inadequate water filling, overfilling, unusual noise near the valve, or a dishwasher that won't start. 110-127V, 60Hz. Replaces 00628334, 3278459, 33199023, 628334, 9000655808, ABS12394, AP5691117, AP7193108, EAP8729241, PD00075605, PS8729241. If you're also seeing a slow leak near the sump area, be aware that on some Bosch models the sump gasket is built into the sump itself rather than sold as a separate part — a leak there is a different repair from this valve. Common Problems This Part Fixes Inadequate water filling the dishwasher Overfilling, which can lead to leaks and water damage Unusual noises coming from the valve area Dishwasher failing to start Poor washing results due to insufficient water supply Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher water inlet valve directly replaces the following OEM and cross-reference part numbers: 10023852, 00628334, 3278459, 33199023, 628334, 9000655808, ABS12394, AP5691117, AP7193108, EAP8729241, PD00075605, PS8729241. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select Bosch dishwashers, and also fits select Thermador, Dacor, and Gaggenau dishwashers built on the Bosch platform, including model numbers such as SHXM98W75N/01, SHX863WD5N/01, SHEM63W55N/01, and SHPM65Z55N/01, and spanning model series SHE, DWH, SHX, SHV, and SHP. Note: This valve is not universal — it's designed for specific Bosch, Thermador, Dacor, and Gaggenau models. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Bosch OEM part — factory-specified solenoid design and flow rate Regulates warm water flow into the dishwasher during each wash cycle Resolves "won't fill properly," "overfilling," "unusual noise," and "won't start" symptoms caused by valve failure Direct drop-in replacement — matches the original mounting and connections Replaces 00628334, 3278459, 33199023, 628334, 9000655808, ABS12394, AP5691117, AP7193108, EAP8729241, PD00075605, PS8729241 Compatible with Bosch, Thermador, Dacor, and Gaggenau dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 10023852 Part Type Dishwasher Warm Water Inlet Valve Condition Genuine OEM Brand Bosch Voltage 110-127V Frequency 60 Hz Function Regulates warm water flow into the dishwasher during fill Repair Difficulty Easy to Moderate Quantity 1 valve Compatible Brands Bosch, Thermador, Dacor, Gaggenau Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. On many Bosch models, pulling the dishwasher out from under the counter gives the best access to the valve and surrounding sump area. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and water line from the old valve, remove its mounting hardware, and pull it free. Install the new 10023852 in the same position, reconnect the water line and electrical connector fully, and secure the mounting hardware. If you're troubleshooting a slow leak in this general area rather than a fill problem, be aware that on some Bosch models the sump gasket is built directly into the sump itself and isn't sold as a separate part — a leak there is a different repair involving the sump assembly (diverter, circulation pump, drain pump, and aqua-sensor) rather than this valve. Restore the water supply and power, then run a test cycle to confirm the dishwasher fills correctly with no leaks. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions My dishwasher isn't filling with enough water. Is this the right part? Yes, this is one of the most direct symptoms of a failed water inlet valve. Since this valve is what admits warm water from your household supply into the dishwasher, mineral buildup, mechanical wear, or an electrical fault can prevent it from opening fully, leaving the dishwasher without enough water for a proper wash. I have a slow leak near the bottom of my dishwasher. Is that this valve too? Not necessarily. One customer traced a slow, worsening leak on a Bosch dishwasher to the sump gasket, not the water valve — and found that on their model, the gasket is built into the sump itself rather than being a separately replaceable part, requiring a more involved repair pulling the sump apart to address it. If your leak is coming specifically from the sump area rather than showing up as a fill problem, it may be a different repair than this valve replacement. What causes this valve to fail over time? The most common cause is mineral buildup from hard water, which can gradually obstruct the valve's internal passages. Mechanical wear and general electrical problems can also affect the valve's ability to open and close correctly over years of use. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Bosch to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10498976 Refrigerator Water Inlet Valve Replaces WPW10498976 The XPARTCO W10498976 is an aftermarket replacement refrigerator water inlet valve assembly compatible with select Whirlpool, Maytag, KitchenAid, Kenmore, and Ikea bottom-freezer and French door refrigerators in the WRB, WRF, MBF, GX5, GB9, GB2, and related series. The water inlet valve is a solenoid-operated valve mounted on the back of the refrigerator that controls the flow of water from the household supply line to the ice maker and, on models with a door dispenser, to the water dispenser. When the solenoid coil burns out or the valve seat becomes clogged with mineral deposits, the ice maker stops producing ice, the water dispenser stops working, water trickles weakly, or water leaks from the valve body. Rated 120V, 50/60Hz, 35W solenoid, this valve measures 3-1/2"L x 2-3/4"W x 3"H and includes the valve body and mounting bracket. It connects via 1/4" inlet fitting to the household supply line and uses push-in tube fittings on the outlet side. It directly replaces WPW10498976, W10420082, W10498974, K-78200, K-78186, 2684516, 2315508, IMV-576, AP6022334, EAP11755667, PD00024636, PS11755667, WP2315576, and WV8047. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO W10498976 Refrigerator Water Inlet Valve fixes Whirlpool-family bottom-freezer and French door refrigerators where the ice maker is not making ice, the water dispenser is not working or producing only a trickle, or water is leaking from the back of the refrigerator. 120V/50-60Hz/35W solenoid, 3-1/2"L x 2-3/4"W x 3"H, includes bracket. 1/4" inlet connection. Replaces WPW10498976, W10420082, W10498974, K-78200, 2684516, AP6022334, PS11755667. Compatible with Whirlpool WRB/WRF, Maytag MBF, KitchenAid, Kenmore, and Ikea. Common Problems This Part Fixes Ice maker not producing ice or producing very small cubes due to insufficient water supply Water dispenser not working — no water flows when the lever or button is pressed Water dispenser producing only a trickle — valve partially blocked or solenoid weakening Water leaking from behind the refrigerator near the water valve Ice maker fills but overflows — valve stuck open and not closing properly Humming sound near the back of the refrigerator when requesting ice or water — solenoid energized but valve not opening No water reaching the refrigerator despite supply line being connected and pressurized Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: WPW10498976, W10498976, W10420082, AWP50873, EAP11755667, PD00024636, AP6022334, PS11755667.  If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select bottom-freezer and French door refrigerators from the following brands and series: Whirlpool refrigerators — WRB322, WRB329, WRF535, WRF555, and related WRB/WRF series (French door and bottom-freezer models) Maytag refrigerators — MBF1958, MBF2258, and related MBF series KitchenAid refrigerators — select bottom-freezer and French door models Kenmore / Sears refrigerators — select Whirlpool-built models Ikea refrigerators — select models (Whirlpool-built) Other Whirlpool-platform models including GB9, GB2, GX5, GX2, ET1CH, ET8CH, IX5HH, ED22, and related series Note: Always verify your exact model number before ordering — water inlet valves are model-specific and not universal across all refrigerator configurations. Check that the supply line connection size (1/4") matches your existing supply line before purchasing. Key Features Solenoid-operated valve — opens on command from the refrigerator's control board to supply water to the ice maker and water dispenser Rated 120V, 50/60Hz, 35W — correct electrical specifications for compatible Whirlpool-family refrigerators Dimensions: 3-1/2"L x 2-3/4"W x 3"H — includes mounting bracket for direct installation 1/4" inlet connection — matches standard residential refrigerator supply line diameter Push-in outlet tube fittings — easy connection to existing water supply tubing inside the refrigerator Plastic and metal construction — durable and resistant to mineral buildup Replaces WPW10498976, W10420082, W10498974, K-78200, K-78186, 2684516, AP6022334, and over 10 additional cross-references Compatible with Whirlpool WRB/WRF series, Maytag MBF series, KitchenAid, Kenmore, and Ikea refrigerators Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number W10498976 OEM Part Number WPW10498976 Part Type Refrigerator Water Inlet Valve Assembly Condition Aftermarket Replacement Application Bottom-Freezer and French Door Refrigerators Voltage 120V AC Frequency 50/60 Hz Solenoid Wattage 35W Dimensions 3-1/2"L x 2-3/4"W x 3"H Inlet Connection 1/4 inch Color Brown / Blue / Yellow / Gray Material Plastic / Metal Includes Water valve body and mounting bracket Compatible Brands Whirlpool, Maytag, KitchenAid, Kenmore, Ikea Installation Notes ⚠️ Unplug Refrigerator and Shut Off Water Before Starting Unplug the refrigerator and shut off the household water supply valve before beginning. Place a towel and small container under the valve area to catch residual water. Pull the refrigerator away from the wall to access the back lower panel — remove the panel screws to expose the water inlet valve. Photograph the wiring harness connections and water tube connections before disconnecting. Turn off the water supply and disconnect the 1/4" supply line from the valve inlet — use an adjustable wrench, as some compression fittings may be stuck. Squeeze the plastic retaining clips on the outlet tube fittings and pull the internal water tubes free. Disconnect the wiring harness. Unscrew the mounting bracket and remove the old valve. Install the new W10498976 valve with its bracket, reconnect the internal water tubes (push until they click), reconnect the wire harness and supply line. Restore water supply and power. Run a water dispenser test and check for leaks. Tools needed: Phillips screwdriver, adjustable wrench, needle-nose pliers. Frequently Asked Questions What does the refrigerator water inlet valve do? The water inlet valve is an electrically controlled solenoid valve that opens on command from the refrigerator's control board to allow household water pressure to push water through to the ice maker fill tube or the water dispenser. When the ice maker calls for water or you press the dispenser lever, the board sends voltage to the solenoid coil, which opens the valve. When the demand is satisfied, the voltage stops, the spring closes the valve, and water flow stops. A failed solenoid coil — or a valve seat clogged with mineral deposits — prevents the valve from opening or closing correctly, causing no water, weak water, overflow, or dripping. What is the difference between W10498976 and WPW10498976? These are the same water inlet valve. WPW10498976 is the updated Whirlpool OEM part number that superseded the original W10498976. The W10420082 and W10498974 are also cross-references for this same valve from earlier production runs. This aftermarket replacement is compatible with all of these numbers. How do I know if the water inlet valve has failed vs. something else? First confirm the household water supply valve behind the refrigerator is fully open and the supply line is not kinked. Then check the water filter — a clogged filter is one of the most common causes of weak or no water flow and is mistaken for a valve failure. If both supply pressure and the filter are good, test the valve's solenoid coil with a multimeter — a working coil reads 200–500 ohms of resistance; an open circuit confirms failure. If the solenoid tests good but the valve still does not open when the control board sends voltage, the valve seat may be physically clogged with mineral deposits and the valve needs to be replaced. My ice maker is not working but my water dispenser is fine — is it the valve? Possibly — but if the water dispenser works normally, the main valve solenoid is likely functioning. On some refrigerator configurations, the ice maker and the dispenser are controlled by separate solenoid ports on the valve assembly. If only the ice maker port has failed, the dispenser can continue working while ice production stops. Test the ice maker solenoid coil separately. However, a more common cause of ice maker failure with a working dispenser is the ice maker module, freezer temperature, or ice maker shut-off arm — rule out those causes before replacing the valve. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from plastic and metal to match the electrical specifications and dimensions of the original WPW10498976 water inlet valve assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

AHA72973309 Genuine OEM LG Washer Drain & Circulation Pump Assembly The AHA72973309 is a genuine LG OEM drain and circulation pump assembly for LG and select Kenmore front-load washers. This is a dual-purpose pump — an Askoll M120-2 unit — that handles two separate jobs from one motor and housing. During the drain portion of the cycle, it pumps wastewater out of the tub and out through the drain hose. During the wash and rinse portions, it switches roles and recirculates water from the bottom of the tub back up through the dispenser and spray nozzle, showering it back over the load. That recirculation spray is what lets LG's front-load washers clean effectively with less water than an older top-load design would need. Because this single assembly performs both functions, a failure here can show up in more than one way: standing water left in the tub after a cycle, a washer that won't complete its drain step, unusual grinding or humming noise, or reduced wash performance if the recirculation spray isn't working even though draining still seems fine. Common causes include debris such as coins, buttons, or lint lodged in the impeller, general wear and tear on the motor bearings, or an electrical failure in the pump motor itself. It directly replaces AP5676608, 2659237, AHA72973304, and PS7788830. As a genuine OEM part, the AHA72973309 is manufactured by LG to factory specifications — guaranteed fit, materials, and performance. Quick Answer The AHA72973309 Genuine OEM LG Washer Drain & Circulation Pump Assembly fixes LG and select Kenmore front-load washers with standing water left in the tub after a cycle, a washer that won't drain, unusual grinding or humming noise, or reduced wash performance from a weak recirculation spray. Askoll M120-2 dual-purpose pump — handles both draining and mid-cycle water recirculation. Replaces AP5676608, 2659237, AHA72973304, PS7788830. Installation is average difficulty, 30 to 60 minutes — and on many models it's accessible through the front panel without needing to tip the washer over. Common Problems This Part Fixes Standing water left in the tub after a cycle finishes Washer won't drain, or drains very slowly Drainage-related error code displayed on the control panel Unusual grinding, humming, or rattling noise during the drain or wash portion of the cycle Reduced wash performance — clothes not getting as clean, possibly from a weak recirculation spray Washer stalling mid-cycle at the drain step Water leaking from underneath the washer near the pump housing Pump that hums but doesn't seem to move water — possible clog or seized impeller Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drain and circulation pump assembly directly replaces the following OEM and cross-reference part numbers: AHA72973309, AHA72973304, AP5676608, 2659237, ALG53336, PD00024680, PS7788830 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain and circulation pump assembly is compatible with select LG front-load washers, and also fits select Kenmore and Kenmore Elite front-load washers built on the LG platform. Note: This is a dual-function drain-and-circulation assembly specific to LG's front-load platform, built around the Askoll M120-2 pump. It is not a drain-only pump, and it is not intended for top-load washers, which use a different pump design. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine LG OEM part — factory-specified motor, impeller, and housing design Dual-purpose Askoll M120-2 pump — drains the tub and recirculates wash water through the dispenser spray nozzle Resolves "standing water in the tub," "won't drain," "grinding or humming noise," and "reduced wash performance" symptoms caused by pump failure Includes all necessary wiring and mounting hardware for a complete replacement Direct drop-in replacement — no modification required Replaces AP5676608, 2659237, AHA72973304, and PS7788830 Compatible with LG and select Kenmore/Kenmore Elite front-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Average installation difficulty — typically 30 to 60 minutes Product Specifications Part Number AHA72973309 Part Type Washer Drain & Circulation Pump Assembly Condition Genuine OEM Brand LG Pump Model Askoll M120-2 Function Drains tub water and recirculates wash water through the dispenser spray Kit Contents Pump assembly with wiring and mounting hardware Application Front-Load Washers (LG-Built) Repair Difficulty Average — 30 to 60 minutes Quantity 1 pump assembly Compatible Brands LG, select Kenmore, Kenmore Elite Installation Notes ⚠️ Unplug Washer And Shut Off Water Before Starting — Drain Residual Water First Disconnect power at the outlet or shut off the circuit breaker, and close the water supply valves before beginning. Wear work gloves. Place towels down and have a shallow pan ready, since the pump housing will hold residual water even after a completed cycle — draining this into a pan before disconnecting hoses will save you a mess. On many models, this pump is fully accessible by removing the front lower access panel or kick plate, without needing to tip the washer onto its back — check this first, since it can save significant time and effort compared to some online guides that recommend tipping the unit. Photograph the hose routing and wiring connections before disconnecting anything. Disconnect the two hose clamps connecting the pump to the tub and drain hose, and unplug the electrical connector from the pump motor. Remove the mounting screws or clips securing the pump assembly and lift it free, checking the impeller area for coins, buttons, or debris while it's out — clearing a clog here may have been the actual cause of the original symptom. Install the new AHA72973309 in the same orientation, reconnect both hoses with their clamps, and reconnect the electrical connector fully. Reinstall the front access panel, restore water and power, and run a short cycle to confirm normal draining, recirculation spray, and no leaks around the pump housing. Tools needed: Phillips screwdriver, hose clamp pliers, shallow pan or towels, work gloves. Frequently Asked Questions Do I really need to tip the washer over to replace this pump? Not necessarily — check your model first. While a lot of general online guidance recommends tipping the washer onto its back to access the pump from underneath, many LG and Kenmore Elite front-load models make this pump fully accessible through the front lower access panel or kick plate instead, without any tipping required. It's worth removing that panel first and seeing what you find before committing to the more involved tip-over approach. Why does this one pump handle both draining and something during the wash cycle? LG's front-load washers use this same Askoll pump for two different jobs at different points in the cycle: pumping wastewater out during the drain step, and recirculating water from the bottom of the tub back up through the dispenser and spray nozzle during wash and rinse to shower it over the load. That recirculation spray is part of how these washers clean effectively while using less water than an older top-load design. Because one pump does both jobs, a failure can affect draining, wash performance, or both, depending on what's actually gone wrong inside it. There's water left in the tub after every cycle. Is this definitely the pump? It's one of the most common causes, but check the easy things first. A clogged drain filter or a kinked drain hose can produce the same "won't drain" symptom and cost nothing to fix. If the filter and hose are clear and water is still standing in the tub, or if the pump hums but doesn't seem to move any water, the pump assembly itself has likely failed. My washer drains fine but clothes aren't coming out as clean. Could this pump be the cause? Possibly. Since this same assembly also handles the recirculation spray during wash, a partial failure can leave draining intact while weakening or eliminating that spray function, which reduces how effectively detergent and water reach the load. If drainage is normal but wash performance has noticeably declined, it's worth having this pump checked as one possible cause alongside things like detergent dosing and water hardness. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It includes the same Askoll M120-2 dual-function pump design, wiring, and mounting configuration as the drain and circulation pump assembly originally installed in your front-load washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM Frigidaire / Electrolux Washer Part 134762010 Washer Genuine OEM Water Level Pressure Switch Monitors air pressure from the washer tub and signals the control system when the correct water level has been reached. Product Overview The Frigidaire 134762010 Washer Water Level Pressure Switch senses changes in air pressure through the washer pressure hose to monitor the amount of water inside the tub. It signals the washer control system when the correct water level has been reached so the appliance can fill, wash, drain, and advance through the cycle correctly. This is a new Genuine OEM Frigidaire / Electrolux replacement part manufactured to the original equipment specifications for proper fit, electrical connection, and operation in compatible washers. Quick Answer 134762010 is a Genuine OEM water-level pressure switch for select Frigidaire, Electrolux, Kenmore, and Crosley front-load washers. It replaces 7134762010. This listing is for the pressure switch only; the pressure hose, clamp, wiring harness, and mounting hardware are not included unless specifically shown. Common Problems This Part May Fix Washer overfills with water Washer does not fill or underfills Incorrect or inconsistent water level Cycle stops or will not advance Washer does not drain or complete the cycle correctly E35 or another water-level-related error on applicable models Replaces and Cross-References 134762010, 1482962, 7134762010, AH2349296, AP4368525, AFR14413, EA2349296, PD00007813, PS2349296. 134762010 is the current manufacturer part number. Other numbers are previous manufacturer or retailer cross-references. Compatibility Designed for select front-load washers manufactured by Electrolux and sold under Frigidaire, Electrolux, Kenmore, and Crosley brand names. Confirmed model examples include: 41741100000 41744130000 EIFLS55IRR0 EIFLS60JIW1 FAFS4473LN0 FAFW3921NW0 FFFW5000QW0 CFW4700LW0 CFW7400QW0 Important: This is a partial compatibility list. Pressure switches can look alike while using different settings, terminals, mounting tabs, or control calibration. Verify the complete washer model number before ordering. Key Features Genuine OEM Frigidaire / Electrolux replacement part Monitors the water level inside the washer tub Signals the control system when the correct fill level is reached Supports proper filling, washing, draining, and cycle operation Snap-tab mounting design on compatible models Designed for original fit and electrical connection Product Specifications Manufacturer Part Number 134762010 Brand Frigidaire / Electrolux Part Type Washer Water Level Pressure Switch Condition New Quality Genuine OEM Application Front-Load Washing Machine Primary Function Senses and controls the washer water level Included One Water Level Pressure Switch Installation Notes Unplug the washer and shut off both water-supply valves. Remove the washer top panel as required for your model. Photograph the wire connector and pressure-hose connection before disconnecting them. Disconnect the electrical connector without pulling on the wires. Release the clamp and carefully remove the pressure hose. Remove the old switch and install the replacement in the same position. Reconnect the hose, clamp, and electrical connector, then reinstall the top panel. Diagnostic tip: Inspect the pressure hose for cracks, pinholes, blockage, moisture, loose connections, or trapped debris. A damaged or obstructed hose can cause the same symptoms as a failed pressure switch. Frequently Asked Questions Is 134762010 a genuine OEM part? Yes. It is a Genuine OEM Frigidaire / Electrolux washer water-level pressure switch. What does the pressure switch do? It monitors air pressure from the washer tub and signals the control system when the correct water level has been reached. Which part number does it replace? It replaces previous manufacturer part number 7134762010. Does this include the pressure hose? No. The listing is for the pressure switch only unless additional components are specifically shown and stated as included. Will it fit every Frigidaire or Electrolux washer? No. Verify the complete appliance model number and required manufacturer part number before purchasing. Shop With Confidence Purchase the correct Genuine OEM replacement part for dependable fit and operation. Verify your washer model number before ordering, and contact our parts team when compatibility assistance is needed. Genuine OEM PartFast U.S. ShippingCompatibility SupportSecure Checkout

Read more less

W10865826 Refrigerator Water Valve - Compatible with Whirlpool, KitchenAid, Maytag, JennAir, Kenmore Product Description Restore your refrigerator’s ice and water dispensing functionality with the replacement W10865826 Refrigerator Water Valve. This replacement part is designed for select Whirlpool, KitchenAid, Maytag, JennAir, and Kenmore refrigerators, ensuring precise water flow control for the ice maker or water dispenser. It resolves issues like no ice production, no water dispensing, or leaks, offering reliable performance and durability. Note: Disconnect power and water supply before installation. Verify model compatibility for proper fit. Replaces part numbers: W10865826, W10394076, WPW10394076, 4459687, W10726788, W10833705, W10872966, PD00041363, EAP11738056, AP6026312, PS11738056.  Compatibility: Compatible with models including but not limited to: Whirlpool: WRF736SDAM, WRF767SDHZ, WRX986SIHZ, KRFF507HPS KitchenAid: KRMF706ESS Maytag: MFI2570FEZ JennAir: JFX2897DRM Kenmore: 10651753710 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand Compatibility: Fits select Whirlpool, KitchenAid, Maytag, JennAir, and Kenmore refrigerators. 🔥 Specifications: Water inlet valve with solenoid, electrical connectors, and water line fittings. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires screwdriver, wrench, pliers; typically installed in 15–30 minutes. 🛡️ Effective Fixes: Resolves no ice, no water dispensing, or water leaks. Product Specification Part Number: W10865826 Component Type: Refrigerator water inlet valve Material: Plastic housing, metal fittings, electrical connectors Mounting: Secures to refrigerator frame with screws Operating Conditions: Suitable for refrigerator water systems Compliance: UL-listed components, Prop 65 warning for California Installation Notes: Safety First: Disconnect the refrigerator from power and water sources before installation. Follow the owner’s manual for guidance. Use plumber’s tape on threaded connections to prevent leaks. Shop for high-quality replacement appliance parts with a 30-day return policy. Fix your refrigerator today! Add to cart now for a reliable solution!

Read more less

242252702 Genuine OEM Frigidaire Refrigerator Water Valve The 242252702 is a genuine Frigidaire OEM triple-solenoid water inlet valve assembly for Frigidaire, Electrolux, Kenmore, Crosley, and White-Westinghouse side-by-side refrigerators. This valve is the central control point where your home's water supply connects to the refrigerator, and it manages water flow to both the ice maker and the door-mounted water dispenser through three separate solenoids housed in one assembly, each opening independently depending on what's being called for. Rated 120V, 50/60Hz per solenoid (20W maroon, 20W yellow, 35W green — each solenoid's wire is color-coded), this valve has 4 outlets total: one 1/4" tube inlet, three 5/16" tube outlets, and one 1/4" tube outlet. It measures approximately 7-1/8"L x 3-3/4"W x 3-1/4"H and ships as a complete assembly with mounting bracket and installation instructions. This valve directly replaces the older 241734302 design and uses updated quick-connect fittings in place of the older screw-on style. A failing valve typically shows up as the ice maker or dispenser not working, slow water flow, or — notably — an overflowing ice maker caused by the valve not shutting off completely if household water pressure is too low. It directly replaces 240321801, 240505101, 240505102, 240508101, 240508102, 240531101, 241734301, 241734302, 7241734301, WV2702, 2692163, AP5671757, EAP7784018, PD00000153, PS7784018, and K-76150. Quick Answer The 242252702 Genuine OEM Frigidaire Refrigerator Water Valve fixes Frigidaire, Electrolux, Kenmore, Crosley, and White-Westinghouse side-by-side refrigerators where the ice maker or water dispenser isn't working, water flow is slow, or the ice maker is overflowing. Triple-solenoid, 4-outlet valve assembly with bracket. Replaces 240321801, 240505101, 240505102, 240508101, 240508102, 240531101, 241734301, 241734302, 7241734301, WV2702, 2692163, AP5671757, EAP7784018, PD00000153, PS7784018, K-76150. This valve needs at least 20 psi of household water pressure to shut off completely — if pressure is too low, the valve can leak and cause the ice maker to overflow even when the valve itself is functioning correctly. Common Problems This Part Fixes Ice maker has stopped making ice, or is producing less ice than usual Water dispenser on the refrigerator door isn't working or has slowed down Ice maker overflowing or leaking Slow water flow at the dispenser Water leaking near the valve at the back of the refrigerator Error code related to the water system displayed on some models Cracked or physically damaged valve housing Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator water valve directly replaces the following OEM and cross-reference part numbers: 242252702, 240321801, 240505101, 240505102, 240508101, 240508102, 240531101, 241734301, 241734302, 2692163, 7241734301, PD00000153, EAP7784018, AP5671757, AFR15932, PS7784018 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select Frigidaire side-by-side refrigerators, and also fits select Electrolux, Kenmore, Crosley, and White-Westinghouse refrigerators built on the same platform, including model numbers such as: BFHS2611LM, BFHS2611LM0 BGHS2634KE0, BGHS2634KE1, BGHS2634KP0, BGHS2634KP1, BGHS2644KF0, BGHS2644KF1 FFSS2615TS0, FFSS2615TE4, FFHS2611PFEA, FFHB2750TD5, FRSS26L3AF0 FRS26H5ASB4, FRS26H5ASB5, FRS26H5ASB8, FRS26H5ASBA, FRS26R2AW6, FRS26R4AW5, FRS26R4CB1, FRS26RLECS0, FRS26LF7DS7 FRS6LR5EB3, FRS6LR5EB6, FRS6LR5EM2, FRS6LR5EM8, FRS6R5ESB4 PLHS69EESS2, PLHS69EGSS1, PLHS269ZCB4, PHSC39EGSS0 Crosley CRSE234FB2 Note: This valve's fitting style has been updated to quick-connect fittings, replacing the older screw-on style used on some earlier units — this may cause the appearance to differ slightly from your original part, but it is a correct functional replacement. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified solenoid design and flow-rate calibration Triple-solenoid assembly supplies water to both the ice maker and door water dispenser Resolves "ice maker not working," "dispenser not working," "slow water flow," and "ice maker overflowing" symptoms Color-coded solenoid wiring (maroon, yellow, green) for straightforward reconnection 4 outlets: 1x 1/4" tube inlet, 3x 5/16" tube outlets, 1x 1/4" tube outlet Updated quick-connect fittings for easier installation than older screw-on designs Ships complete with mounting bracket and installation instructions Replaces the full cross-reference list above, including the older 241734302 design Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 242252702 Part Type Refrigerator Water Inlet Valve (Triple Solenoid) Condition Genuine OEM Brand Frigidaire Application Side-by-Side Refrigerators Voltage 120V per solenoid Frequency 50/60 Hz per solenoid Wattage 20W (maroon), 20W (yellow), 35W (green) Outlets 1x 1/4" tube inlet, 3x 5/16" tube outlets, 1x 1/4" tube outlet Dimensions 7-1/8"L x 3-3/4"W x 3-1/4"H Weight Approx. 1.08 lbs. Minimum Water Pressure 20 psi (required to shut off fully) Kit Contents Valve assembly, mounting bracket, installation instructions Color Gray / Blue / Green / Yellow / Maroon Material Plastic / Metal Quantity 1 valve assembly Compatible Brands Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse Installation Notes ⚠️ Unplug Refrigerator And Shut Off Water Supply Before Starting Disconnect power at the outlet and shut off the water supply before beginning. Wear work gloves. Pull the refrigerator away from the wall for access, then locate the valve at the rear of the cabinet. Remove the two hex screws securing the old valve. Before disconnecting anything, note or photograph which plastic tube connects to which port on the multi-port valve assembly — with three solenoids and multiple outlets, getting a hose on the wrong port will send water to the wrong place. Disconnect the water supply hose, the electrical connectors (which are color-coded to their matching solenoids on the new valve), and the outlet hoses, then remove the old valve. Install the new 242252702 in the same position with its included mounting bracket, secure it with the hex screws, and reconnect each outlet hose to its correct port exactly as noted. Reconnect the color-coded electrical connectors to their matching solenoid wires. Reattach the water supply hose, tightening securely. While the back of the refrigerator is accessible, it's also a good opportunity to clean the condenser coils and surrounding area. Restore the water supply and check every connection for leaks before restoring power. Push the refrigerator back into place, then test both the ice maker and water dispenser over the following day. Tools needed: hex screwdriver or nut driver, pliers, work gloves. Frequently Asked Questions My ice maker is overflowing. Is this the valve? Possibly, but check your household water pressure first. This valve requires a minimum of 20 psi to shut off fully — if your home's water pressure is below that, the valve may not close completely even though it's functioning correctly, letting water leak through and overflow the ice maker. If your water pressure tests below 20 psi, that's the underlying cause rather than a defective valve, and addressing the pressure issue (or installing a pressure-boosting solution) is the correct fix. The new valve looks different from my old one. Is that normal? Yes. This valve has been updated to use quick-connect fittings in place of the older screw-on style used on earlier units, so the connection points may look different from what you're used to. It's still a correct, direct functional replacement — the new fittings just make installation somewhat easier. How do I know which hose goes where? This valve has multiple outlets. Note or photograph the hose routing on your old valve before disconnecting anything — with three solenoids and four total outlets, it's easy to reverse a connection if you're not careful. The electrical connectors are color-coded (maroon, yellow, green) to help you match them to the correct solenoid on the new valve, which makes the wiring side more foolproof than the hose routing. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original triple-solenoid design, wattage per solenoid, and outlet configuration of the water valve originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WP3363892 Washer Genuine OEM Drain Pump Drain pump for belt-less direct-drive washer Oversized 1-3/4" outlet with flapper with back flow flapper valve Replaces Part Numbers:3363892, 3352496, AP6008110, PS11741242, WP3363892VP, B002CRSNT4, LP121   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

242253002 Refrigerator Genuine OEM Water Valve Replaces Part Numbers:242253002, 242102201, 2689640, OEM22679498, AP5669874, PS7321353. Description: This Water Inlet Valve is a Genuine OEM part for specific Frigidaire refrigerator models. It is designed to manage the flow of water to the ice maker and water dispenser. This solenoid-operated valve responds to commands from the refrigerator's electronic control, opening to allow water in and closing to stop the flow, ensuring proper operation of both ice production and water dispensing functions.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less