XPARTCO W10276397 Washer Drain Pump Replaces WPW10276397
The XPARTCO W10276397 is an aftermarket replacement washer drain pump and motor assembly compatible with a wide range of Whirlpool-family top-load washers including Whirlpool Cabrio, Maytag Centennial, Amana, Kenmore, Roper, Crosley, and Inglis. The drain pump removes water from the washer tub during the drain portion of each wash cycle. When the pump fails, the washer will not drain, will leave standing water in the tub, display error code F9E1, stop mid-cycle, or produce unusual humming or grinding noises during the drain phase.
This complete drain pump and motor assembly uses a Hanyu B40-3A motor (also marked 91PS3132) and includes the integrated impeller — the impeller is not sold separately. It directly replaces WPW10276397, W10276397, WPW10276397VP, 1874334, B40-3A, LP397, AP6018417, PS11751719, and several additional cross-reference numbers. Before ordering, confirm that the drain hose and any coin trap or filter are clear — a blocked hose or clogged filter can mimic pump failure symptoms. Installs in 20–30 minutes with basic hand tools.
Quick Answer
The XPARTCO W10276397 Washer Drain Pump fixes Whirlpool Cabrio and Maytag Centennial top-load washers that won't drain, leave standing water, display error code F9E1, or make humming/grinding noises during the drain cycle. Complete pump and motor assembly with integrated impeller. Motor: Hanyu B40-3A / 91PS3132. Replaces WPW10276397, 1874334, B40-3A, LP397, AP6018417, PS11751719. Compatible with Whirlpool Cabrio, Maytag Centennial/MVWC/MVWX, Amana, Kenmore, Roper, Crosley, and Inglis top-load washers.
Common Problems This Part Fixes
Washer not draining — standing water remaining in the tub after a cycle
Error code F9E1 displayed — drain pump fault or slow drain detected
Washer stopping mid-cycle due to a drain fault
Loud humming during the drain phase — motor running but impeller not pumping
Grinding or rattling noise during drain — physical damage to impeller or pump housing
Water draining very slowly — worn pump motor below rated flow
Water leaking from the drain pump area
Replaces Part Numbers
This drain pump directly replaces the following OEM and cross-reference part numbers:
WPW10276397, W10276397, 1874334, AP6018417, AWP50231 EAP11751719 FIX11751719, OEM24073670, PD00003595, PS11751719, WPW10276397VP
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain pump is compatible with select top-load washers from the following brands and series:
Whirlpool top-load washers — Cabrio series (WTW4800, WTW4810, WTW4850, WTW4900, WTW5000, WTW5200, WTW5300, WTW5500, WTW5600, WTW5640, WTW5700 and related models)
Maytag top-load washers — Centennial series (MVWC200, MVWC215, MVWC300, MVWC400, MVWC415, MVWC416, MVWC425, MVWC465 and related models)
Maytag top-load washers — MVWX series (MVWX500, MVWX550, MVWX600, MVWX700 and related models)
Amana top-load washers (ATW, NTW series and related models)
Kenmore / Sears top-load washers — 110 series (Whirlpool-built Cabrio-platform models)
Roper top-load washers (RTW series)
Crosley top-load washers (CAE series)
Inglis top-load washers (select models)
Note: This pump is for top-load washers only. Always verify your exact model number before ordering. Check and clear the drain hose and any coin trap before replacing the pump — a blocked hose can produce the same symptoms as a failed pump.
Key Features
Removes water from the tub during the drain and spin cycles for proper washer operation
Complete pump and motor assembly — includes integrated impeller (impeller not sold separately)
Motor: Hanyu B40-3A / 91PS3132 — matched to original pump specifications
Resolves error code F9E1 (drain pump fault / slow drain) on compatible Whirlpool and Maytag top-load washers
Replaces WPW10276397, W10276397, 1874334, B40-3A, LP397, and AP6018417
Compatible with Whirlpool Cabrio, Maytag Centennial/MVWX, Amana, Kenmore, Roper, Crosley, and Inglis top-load washers
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 20–30 minutes with basic hand tools
Product Specifications
Part Number
W10276397
OEM Part Number
WPW10276397
Part Type
Washer Drain Pump and Motor Assembly
Condition
Aftermarket Replacement
Application
Top-Load Washers (Cabrio, Centennial, and related platforms)
Motor
Hanyu B40-3A / 91PS3132
Includes
Pump motor and integrated impeller assembly
Error Code Resolved
F9E1 (drain pump fault / slow drain)
Compatible Brands
Whirlpool, Maytag, Amana, Kenmore, Roper, Crosley, Inglis
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. Place towels and a shallow pan near the pump access area to catch residual water. The drain pump is located beneath the washer tub on Cabrio and Centennial models — access it by removing the front lower panel or by tilting the washer back and working from underneath. Disconnect the drain hose clamp and hose from the pump, then disconnect the wire harness connector. Unscrew the pump mounting screws and remove the old pump. Before installing the new pump, verify the drain hose and any coin trap or filter are completely clear of debris — a blocked hose or trap will cause the new pump to fail again. Install the new W10276397 pump in the same position, reconnect the hose and wire harness, and secure the mounting screws. Restore power and water and run a drain or spin cycle to confirm drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan, towels.
Frequently Asked Questions
What does error code F9E1 mean on Whirlpool Cabrio and Maytag Centennial washers?
F9E1 indicates a drain fault — the washer was unable to drain within the expected time during the cycle. It can be caused by a clogged drain hose, a blocked coin trap or filter, a kinked drain hose, or a failed drain pump motor. Always check and clear the drain hose and filter before replacing the pump — a blockage is often the cause and clearing it resolves the error without needing a new pump. If the hose and filter are clear and the error persists, the pump motor has likely failed.
What is the difference between W10276397 and WPW10276397?
These are the same drain pump assembly. WPW10276397 is the updated Whirlpool OEM part number that superseded the original W10276397. The 1874334 and B40-3A are also cross-references for this same pump. This aftermarket replacement is compatible with all of these numbers.
My washer hums but won't drain — is it the pump?
A humming sound during the drain cycle without water being expelled usually means the pump motor is receiving power and running, but the impeller is not turning — either because it is jammed with debris or because the impeller shaft has broken. First check for and remove any foreign objects (coins, lint, small clothing items) from the pump area. If the impeller is clear and the pump still hums without draining, the motor or impeller is mechanically failed and the pump assembly needs replacement.
Does this pump fit the Whirlpool Cabrio and Maytag Bravos washers?
The W10276397 is compatible with Whirlpool Cabrio and Maytag Centennial top-load washers on the VM transmission platform. Maytag Bravos XL and Bravos X models may also be compatible depending on the specific model number — verify your exact model before ordering. Contact our support team if you need confirmation for a specific Bravos model.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured with a Hanyu B40-3A motor to match the specifications and performance of the original WPW10276397 drain pump assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
WH13X10024 Genuine OEM Washer Water Valve
Replaces Part Numbers: WH13X10024, WH13X0086, WH13X0087, WH13X10004, WH13X10019, WH13X86, WH13X87, AH1155105, EA1155105, OEM15444478, AP3861119, PS1155105.
Description: This Water Inlet Valve is a Genuine OEM part for select GE washing machine models. This component is crucial for controlling the flow of water into the washer during the wash and rinse cycles. It works by opening and closing the solenoids to allow the appropriate amount of hot or cold water to enter the washing machine, based on the selected settings.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO WH01X24697 Washer Drive Belt
The XPARTCO WH01X24697 is an aftermarket replacement drive belt for GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café models. This belt connects the drive motor to the drive system, transmitting rotation to spin the basket during the wash and spin cycles.
Measures approximately 21" long, made of durable, flexible rubber engineered to reduce slipping and squeaking while withstanding regular tension and wear. Over time, the belt stretches, cracks, or breaks from age and normal use. If your washing machine is making unusual noise, not spinning correctly, or the basket isn't moving, this drive belt may be the cause. It directly replaces 4585709, 290D1101P003, 5PJ576SJ83, AGE26179, AP6037512, EAP11767488, OEM18112545, PD00034405, PS11767488.
Quick Answer
The XPARTCO WH01X24697 Washer Drive Belt fixes GE, Hotpoint, Haier, Monogram, and Café top-load washers with unusual noise, a basket that won't spin correctly, or a basket that isn't moving at all. Approximately 21" long. Replaces 4585709, 290D1101P003, 5PJ576SJ83, AGE26179, AP6037512, EAP11767488, OEM18112545, PD00034405, PS11767488. Not the same as the similarly-numbered WH01X24180 or WH01X27538 belts, which are separate parts used on other GE/Hotpoint models — confirm your exact part number before ordering.
Common Problems This Part Fixes
Basket not spinning or not moving at all
Unusual noise during operation, including squeaking
Basket slipping or spinning inconsistently
Wash cycle running without proper agitation or spin
Belt visibly stretched, cracked, or broken
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer drive belt directly replaces the following OEM and cross-reference part numbers:
WH01X24697, 4585709, 290D1101P003, 5PJ576SJ83, AGE26179, AP6037512, EAP11767488, OEM18112545, PD00034405, PS11767488
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drive belt is compatible with select GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café washers built on the GE platform, including model numbers such as GTW220ACK1WW, GTW220ACK2WW, GTW220ACK3WW, GTW330ASK0WW, GTW330ASK1WW, GTW330ASK2WW, GTW460AMJ1WW, GTW460AMJ3WW, GTW460AMJ4WW, GTW460ASJ1WW, GTW460ASJ3WW, GTW460ASJ4WW, GTW460ASJ5WW, GTW460ASJ6WW, GTW460ASJ7WW, HTW200ASK0WW, HTW200ASK1WW, HTW200ASK2WW, HTW240ASK0WS, HTW240ASK1WS, and HTW240ASK2WS.
Note — not the same as WH01X24180 or WH01X27538: These are separate GE/Hotpoint drive belts with their own cross-reference sets, used on different models. The similar numbering makes them easy to confuse. Always verify your exact part number before ordering. Contact our support team with your model number if you're unsure which belt your washer needs.
Key Features
Aftermarket replacement drive belt — connects the drive motor to the drive system to spin the basket
Resolves "won't spin," "unusual noise," and "basket not moving" symptoms caused by belt failure
Approximately 21" long
Durable, flexible rubber construction engineered to reduce slipping and squeaking
Direct drop-in replacement matching the original length and profile
Replaces 4585709, 290D1101P003, 5PJ576SJ83, AGE26179, AP6037512, EAP11767488, OEM18112545, PD00034405, PS11767488
Compatible with GE, Hotpoint, Haier, Monogram, and Café top-load washers
Aftermarket replacement built to OEM-equivalent quality standards
Straightforward DIY repair with basic tools
Product Specifications
Part Number
WH01X24697
OEM Part Number
WH01X24697
Part Type
Washer Drive Belt
Condition
Aftermarket Replacement
Length
Approx. 21"
Material
Rubber
Function
Connects the drive motor to the drive system to spin the basket
Repair Difficulty
Easy to Moderate
Quantity
1 drive belt
Compatible Brands
GE, Hotpoint, Haier, Monogram, Café
Installation Notes
⚠️ Unplug Washer Before Starting Disconnect power at the outlet before beginning. Wear work gloves. Remove the back panel of the washer using a socket wrench set, taking out the securing screws and carefully lifting the panel away. Locate the drive belt near the motor, at the bottom of the washer. Use a screwdriver to loosen the tensioner, then gently slide the old belt off the pulleys. Fit the new WH01X24697 belt around the pulleys in the same path as the old one, then re-tension it with the tensioner. Reinstall the back panel and secure its screws. Restore power and run a test cycle to confirm the basket spins smoothly with no unusual noise. Tools needed: socket wrench set, screwdriver, work gloves.
Frequently Asked Questions
My washer's basket isn't spinning. Is this the belt I need?
Yes, this is one of the most common symptoms of a failed drive belt. Since this belt is what transmits rotation from the drive motor to the basket, a stretched, cracked, or broken belt can leave the motor running while the basket doesn't spin correctly or at all.
Is this a difficult repair?
No, it's a straightforward repair for a confident DIYer with basic tools. It involves removing the back panel to access the belt near the motor, loosening the tensioner, and swapping the belt — no specialized skills required.
Is this the same as WH01X24180 or WH01X27538?
No, these are separate GE/Hotpoint drive belts with their own distinct cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old belt rather than assuming based on a close number match.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the length, material, and pulley fit of the original WH01X24697 drive belt used in compatible GE, Hotpoint, Haier, Monogram, and Café top-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
W10356257 Washer Genuine Water Valve
Fits Specific Whirlpool, Maytag Washer Model
Replaces Part Numbers: WPW10356257, W10356257, 1938138, W10336721, W10337338, W10352254, AP6020342, PS11753661.
Description: This Water Inlet Valve is a Genuine part for specific Maytag, Whirlpool washing machine models. This part controls the flow of water into the washer during the filling cycles. This valve ensures that the correct amount of water is delivered to the tub, allowing for optimal washing performance. Common causes of a bad water inlet valve can include mineral buildup, electrical issues, or wear and tear from regular use.
XPARTCO DC97-20621C Washer Drain Pump Assembly
The XPARTCO DC97-20621C is an aftermarket replacement drain pump assembly compatible with a wide range of Samsung front-load washers in the specific series, as well as select Kenmore front-load washers built on the Samsung platform. The drain pump removes water from the washer tub during the drain portion of each wash cycle. When the pump fails, the washer will not drain, leave standing water in the tub, stop mid-cycle, display error codes 5C, SE, nd, 5E, or 4E, or make loud grinding or humming noises during the drain phase.
The DC97-20621C is the current production revision of this pump, which also covers the earlier DC97-20621A variants — all three are the same pump in successive production runs. It also replaces DC97-17999N, DC31-00187A, PX3516-01, AP6807020, 4959632, PS12592830, and EAP12592830. Before ordering, always check the drain filter/coin trap at the bottom front of the washer — a clogged filter is a common cause of drain error codes that does not require pump replacement. Installs in 20–30 minutes with basic hand tools.
Quick Answer
The XPARTCO DC97-20621C Washer Drain Pump Assembly fixes Samsung front-load washers displaying error codes 5C, SE, nd, 5E, or 4E, not draining, leaving standing water, or making loud grinding or humming noises during the drain cycle. Covers DC97-20621A and DC97-20621B variants. Compatible with select Samsung series and Kenmore (Samsung-built). Replaces DC97-20621A, DC97-17999N, DC31-00187A, PX3516-01, AP6807020, 4959632, PS12592830, EAP12592830. Check drain filter before replacing pump.
Common Problems This Part Fixes
Washer not draining — standing water remaining in the tub after a cycle
Error codes 5C, SE, nd, 5E, or 4E displayed — drain fault detected
Washer stopping mid-cycle due to a drain fault
Loud humming during the drain phase — pump motor running but not pumping
Grinding or rattling noise during drain — damaged impeller or worn pump bearings
Water draining very slowly — worn pump below rated performance
Clothes excessively wet after a cycle — pump not fully removing water before spin
Water leaking from the pump area at the front bottom of the washer
Replaces Part Numbers
This drain pump directly replaces the following OEM and cross-reference part numbers:
DC97-20621C, DC97-17999N, DC97-20621A, 03DC31-00187A, AP7366238, ASM105564, PFIX17701443, PD00095227, PX3516-01, PS17701443, AP6807020, PS12592830.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain pump is compatible with select Samsung front-load washers and related Kenmore models:
Samsung series — WF50R8500AW, WF45T6200AW, WF53BB8900 and related models
Kenmore / Sears front-load washers (select Samsung-built models)
Important: Before replacing the pump, check and clean the drain filter/coin trap located behind the lower access panel at the front of the washer. A clogged filter causes the same error codes as a failed pump and is the most common fixable cause of Samsung front-load drain errors. Always verify your model number before ordering.
Key Features
Removes water from the tub during drain and spin cycles for proper washer operation
Resolves Samsung error codes 5C, SE, nd, 5E, and 4E caused by drain pump failure
DC97-20621C is the current production revision — covers DC97-20621A and DC97-20621B as well
Also replaces DC97-17999N, DC31-00187A, PX3516-01, AP6807020, 4959632, PS12592830, and EAP12592830
Compatible with select Samsung series and Kenmore Samsung-built front-load washers
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 20–30 minutes with basic hand tools
Product Specifications
Part Number
XPDC97-20621C
Also Covers
DC97-20621A (prior revisions)
Part Type
Front-Load Washer Drain Pump Assembly
Condition
Aftermarket Replacement
Application
Samsung Front-Load Washers
Error Codes Resolved
5C, SE, nd, 5E, 4E
Compatible Brands
Samsung, Kenmore (Samsung-built)
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. Place towels on the floor in front of the washer — residual water will drain when the pump is disconnected. The drain pump is accessed through the lower front panel. Remove the lower kick panel screws to expose the drain filter and pump area. First, drain residual water by removing the drain filter cap (have a shallow pan ready — up to a quart of water may flow out). After draining, disconnect the pump wiring harness. Release the hose clamps and disconnect the drain hoses from the pump. Unscrew or unclip the pump mounting hardware and remove the old pump. Install the new DC97-20621C pump in the same position, reconnect drain hoses and secure clamps, reconnect the wiring harness, and reinstall the front panel. Restore power and water and run a drain/spin cycle to confirm drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan, towels.
Frequently Asked Questions
What is the difference between DC97-20621C and DC97-20621A?
These are successive production revisions of the same Samsung front-load washer drain pump assembly. DC97-20621A was the original version, DC97-20621B was an intermediate revision, and DC97-20621C is the current production part. All three are the same pump with minor manufacturing changes across production runs — they are fully interchangeable. If your washer's parts diagram or old pump label shows any of these numbers, this replacement covers all of them.
What error codes indicate a drain pump failure on Samsung front-load washers?
Error codes 5C, SE, nd, 5E, and 4E on Samsung front-load washers all indicate a drain fault — the washer was unable to drain within the expected time. Before replacing the pump, clean the drain filter/coin trap at the front lower access panel — lint, coins, and debris in the filter are among the most common causes of these error codes. If the filter is clean and the errors persist, the pump itself has failed and needs replacement.
Where is the drain filter on my Samsung front-load washer?
The drain filter (also called the coin trap) on Samsung front-load washers is located behind the lower front access panel, typically on the right side. Remove the lower kick panel by pressing the release tab or removing the screws. You will see a small cap or twist-out cover — that is the filter. Place a shallow pan under it and slowly unscrew the cap to allow water to drain out. Remove any debris from the filter, then replace the cap and reinstall the panel. Run a cycle to check if the error clears. If the filter was clogged, this may be all the repair needed.
My washer makes a loud noise during draining — is it the pump?
A loud humming or grinding during the drain cycle is a common sign of a failing pump. Humming without water movement means the motor is running but the impeller is not pumping — either jammed by debris or mechanically failed. Grinding suggests worn pump bearings or a damaged impeller. Check the drain filter first for foreign objects. If the filter is clear and the noise persists, the pump needs replacement.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the specifications and performance of the original DC97-20621C drain pump assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
WP3347288 Washer Lower Agitator
Fits Specific Top Load Washer Models.
Replaces Part Number: WP3347288, 3347288, 3348245, 3352107, 519233, AP6008022, PS11741151.
Description: The Lower Agitator is an OEM part designed for select Kenmore, Whirlpool top-loading washing machines. It sits at the bottom of the wash tub and plays a key agitation role during cycles. This is the bottom part of the agitator assembly.
285751 Washer Genuine Agitator Dog Cam Kit
Replaces Part Numbers: 285751, 2837, 3351019, 387092, 3947410, AH334624, EA334624, OEM9283568, AP3094521, PS334624.
Description: This Agitator Kit is an OEM replacement part for specific Whirlpool top-loading washer models. Installed in the center of the wash basket, it aids in the mechanical agitation central to regular laundry cleaning.It contains the plastic cam and four plastic dogs needed to repair a malfunctioning or noisy agitator during the wash cycle.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
W10876600 Washer Genuine OEM Drain Pump – Compatible with Whirlpool, Maytag, Amana, and Crosley Washers
Product Description
Quickly and efficiently remove water from your washer with the W10876600 Washer Genuine OEM Drain Pump. This factory-approved replacement pump removes water from the tub during wash and spin cycles, ensuring smooth performance and proper draining. A faulty drain pump can cause standing water, error codes, or incomplete cycles. Replacing it with this Genuine OEM part restores dependable drainage and long-lasting washer performance.
Replaces Part Numbers
W10876600, 4455877, W10727777, W10876600VP, PD00034529, EAP11738156, AP6004933, PS11738156.
Compatibility
This Genuine OEM drain pump fits select Whirlpool, Maytag, Amana, and Crosley top-load and front-load washers.
Example compatible models include (but are not limited to): Whirlpool WTW5000DW1, Maytag MVWC465HW0, and Amana NTW4516FW3.
Always verify your washer’s model number before ordering. Contact our support team if you’re unsure.
✅ Key Features
🔄 Genuine OEM Replacement – Factory-approved for perfect fit and reliable operation
💧 Efficient Water Removal – Quickly drains water from the washer tub after each cycle
💪 Durable Motor Design – Built to withstand repeated use and heavy loads
🛠️ DIY Installation – Direct-fit replacement installs easily with basic tools
🛡️ Fixes Common Issues – Solves washer not draining, standing water, or “F9E1”/“SD” error codes
📐 Product Specification
Part Number: W10876600
Component Type: Washer Drain Pump Assembly
Material: Heavy-duty plastic pump housing and electric motor
Voltage: 120V AC
Mounting: Direct-fit on washer base with wiring harness connection
Compliance: Genuine OEM certified
🛠️ Installation Notes
Tools Needed: Nut driver, pliers, towel or bucket
⚠️ Safety First: Always unplug the washer and disconnect water supply before performing repairs to prevent electrical shock or leaks.
Steps:
Disconnect power and water hoses.
Tilt the washer back or remove the front access panel.
Unplug the wiring harness and loosen the clamps on the drain hoses.
Remove the old pump and install the new W10876600 pump.
Reconnect hoses and wiring, secure the pump, and restore power.
Run a rinse or drain cycle to verify proper operation.
⏱️ Time Required: 20–30 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Genuine OEM Replacement Part
🔄 30-Day Return Policy
Fix washer drainage issues fast — Add to Cart Now for a factory-quality repair that lasts!
W11248040 Washer Console (Control Panel Housing)
Genuine Whirlpool part
Replaces Part Number W11248040, 4845509, W11035013, W11120176, W11192407, PD00087512, EAP12584120, AP6783239, PS12584120.
Model Cross Reference
This part #W11248040 works with all models listed.
Kenmore / Sears
110.27132412
Washer
Kenmore / Sears
110.27132413
Washer
W11205048 Washer Genuine OEM Water Valve
Fits select Kenmore, Maytag, Whirlpool top load washer models.
Replaces Part Numbers: W11205048, 4814041, W10843663, AP6327347, PS12349203.
Description: This Water Inlet Valve is a Genuine OEM part for specific Whirlpool washing machine models. This valve controls the flow of water into the washer, allowing it to fill with the correct amount of water during the wash and rinse cycles. Over time, the water inlet valve can become clogged with debris, develop electrical issues, or wear out, leading to problems with the water flow. Causes of a bad water inlet valve include mineral buildup from hard water, internal component failure, or damage to the valve body.
W11210459 Genuine OEM Whirlpool Washer Water Inlet Valve
The W11210459 is a genuine Whirlpool OEM water inlet valve for Whirlpool top-load washers, and also fits select Kenmore, Maytag, Amana, Crosley, Inglis, and Roper models. This valve controls the flow of hot and cold water into the tub during the fill portion of each cycle — an electrical solenoid opens and closes the valve to admit exactly the right amount of water for the selected wash setting.
Over time, mineral or sediment buildup inside the valve, or general wear in the solenoid coil, can cause the valve to fail. A failing valve typically shows up as the washer not filling with water, filling very slowly, or water continuing to leak into the tub after the wash has completed. It directly replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, and W11210459VP.
Quick Answer
The W11210459 Genuine OEM Whirlpool Washer Water Inlet Valve fixes Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, and Roper top-load washers that won't fill, fill very slowly, or continue leaking water into the tub after the wash has finished. Replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, W11210459VP. The control panel can be removed more easily with a putty knife slid under each end to release the clips, rather than removing the back panel first.
Common Problems This Part Fixes
Washer not filling with water
Washer filling very slowly
Water continuing to leak into the tub after the wash cycle has completed
No hot water reaching the tub, or no cold water reaching the tub
Cycle stalling at the fill step and never advancing to wash
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer water inlet valve directly replaces the following OEM and cross-reference part numbers:
W11210459, W10701459, W10838319, W11038711, 4591321, W10869799, W11025984, 33190189, 33190190, W10423122, W10423124, W10868380, W10868381, AP6329217, AWP43369, EAP12349267, OEM18987660, PD00042885, PS12349267
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This water inlet valve is compatible with select Whirlpool top-load washers, and also fits select Kenmore, Maytag, Amana, Crosley, Inglis, and Roper washers built on the Whirlpool platform, including model numbers such as WTW5000DW1 and WTW4816FW2.
Note — not the same as W11210463: A similarly-numbered valve, W11210463 (also cross-referenced as W11101906), is a separate part with its own cross-reference set (W10701461, W10883458, W10869803, W11038696, AP6329219), used on other Whirlpool washer models. The two are easy to confuse given how close the numbers are — always confirm you have the exact part number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate
Regulates hot and cold water flow into the washer tub
Resolves "won't fill," "fills slowly," and "leaks after cycle completes" symptoms caused by valve failure
Factory Certified Part built to Whirlpool's engineering specifications
Direct drop-in replacement — matches the original mounting and hose connections
Replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, and W11210459VP
Compatible with Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, and Roper top-load washers
Genuine OEM replacement — guaranteed fit, materials, and performance
Moderate DIY repair
Product Specifications
Part Number
W11210459
Part Type
Washer Water Inlet Valve
Condition
Genuine OEM
Brand
Whirlpool
Application
Top-Load Washers
Function
Controls hot and cold water flow into the tub
Repair Difficulty
Moderate
Quantity
1 valve
Compatible Brands
Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, Roper
Installation Notes
⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Use A Putty Knife To Release The Control Panel Disconnect power at the outlet, or shut off the house circuit breaker for the appliance, and shut off both hot and cold water supplies before beginning. Wear work gloves. The top control panel can be removed more easily by sliding a putty knife under the panel on each end to release the retaining clips, rather than removing the back panel first — one customer specifically noted this trick saved considerable time after trying the back-panel approach without success. With the panel released, locate the water inlet valve and photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the hot/cold water lines from the old valve, remove its mounting screws, and pull it free. Install the new W11210459 in the same position, reconnect the water lines and electrical connector fully, and secure the mounting screws. Reinstall the control panel. Restore the water supply and power, then run a full test cycle across a few temperature settings to confirm correct fill behavior with no leaking. Tools needed: multi-screwdriver, putty knife, work gloves.
Frequently Asked Questions
My washer isn't filling with water. Is this the right part?
Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the washer, a solenoid failure or internal blockage can prevent any water from entering at all, stopping the wash cycle from proceeding.
What's the easiest way to access the control panel for this repair?
Try sliding a putty knife under the panel at each end to release the retaining clips, rather than removing the back panel of the washer first. One customer specifically learned this trick after trying the back-panel approach with no luck, then found the putty knife method worked cleanly after watching an online tutorial.
Is this the same as W11210463?
No, these are two separate Whirlpool valve part numbers with different cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close number match.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your washer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
