Search results for "Refrigerator Water Valve"

W11168743 Genuine OEM Whirlpool Washer Hot Water Inlet Valve The W11168743 is a genuine Whirlpool OEM hot water inlet valve for Whirlpool top-load washers. This is a single-solenoid valve dedicated specifically to hot water, with a standard hose fitting inlet and one water outlet. When the wash cycle calls for hot water, the valve's solenoid opens to admit it from your home's hot water supply line; once the correct fill level is reached, it closes again. Rated 120V, 60Hz. Common causes of failure include wear and tear over time, clogging from mineral deposits or sediment in the water supply, and electrical faults that prevent the valve from opening or closing properly. A failing hot water valve typically shows up as the washer not filling properly or not filling at all, slow or irregular water flow even when the inlet screens are clear of obstruction, no hot water reaching the tub, or water dripping inside the tub when the washer isn't running. It directly replaces AP6327638, WPW10240948, W10240948, 4585634, PS12348074, W10921515, and 33390068. Quick Answer The W11168743 Genuine OEM Whirlpool Washer Hot Water Inlet Valve fixes Whirlpool top-load washers (and select Maytag, KitchenAid, Jenn-Air, Amana, Roper, and Kenmore washers) that won't fill, fill slowly, have no hot water reaching the tub, or leak water inside the drum when not running. 1-solenoid, 1-inlet, 1-outlet hot water valve. 120V, 60Hz. Replaces AP6327638, WPW10240948, W10240948, 4585634, PS12348074, W10921515, 33390068. This is the hot valve — the matching cold valve for the same platform is a separate part, W11168740. Common Problems This Part Fixes Washer not filling properly, or not filling at all Water flow slow or irregular even when inlet screens are clear No hot water reaching the tub during the wash cycle Water dripping or leaking inside the tub when the washer isn't running Washer not washing properly due to insufficient hot water Washer that won't start because it's stuck waiting for water Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer hot water inlet valve directly replaces the following OEM and cross-reference part numbers: W11168743, 1873019, 33390068, 4585634, W10240948, W10921515, WPW10240948, AP6017592, AP6327638, EAP11750891, EAP12348074, PS11750891, AWP43142, OEM18982923, PD00040928, PS12348074. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This hot water inlet valve is compatible with select Whirlpool top-load washers, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, Hardwick, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Caloric, Kenmore, and Ikea washers built on the Whirlpool platform. Note — hot valve, not cold: This is the hot water valve. The matching cold water valve for the same Whirlpool top-load platform is a separate part, W11168740 (blue body, 2-solenoid). The two are not interchangeable, so replace the correct one for the symptom you're seeing — or both if you're unsure which is causing the issue. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid design and flow-rate calibration Dedicated hot water valve — standard hose fitting inlet, single water outlet Resolves "won't fill," "fills slowly," "no hot water," and "leaking inside the tub" symptoms caused by valve failure Rated 120V, 60Hz Direct drop-in replacement — matches the original mounting and hose connections Replaces AP6327638, WPW10240948, W10240948, 4585634, PS12348074, W10921515, and 33390068 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Roper, and Kenmore top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11168743 Part Type Washer Hot Water Inlet Valve Condition Genuine OEM Brand Whirlpool Application Top-Load Washers Voltage 120V Frequency 60 Hz Solenoids 1 Inlets 1 (standard hose fitting) Outlets 1 Companion Part W11168740 (cold water valve, 2-solenoid, sold separately) Quantity 1 valve Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Roper, Admiral, Hardwick, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Caloric, Kenmore, Ikea Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the hot water supply valve before beginning. Wear work gloves. Access is typically from the rear of the washer: remove the screws securing the top or rear panel to reach the valve. Have a towel handy for residual water when you disconnect the supply hose. Photograph the wiring and hose connections before disconnecting anything. Disconnect the hot water supply hose, disconnect the electrical connector, and remove the mounting screws holding the valve in place, then pull it free. Install the new W11168743 in the same position, secure the mounting screws, and reconnect the electrical connector fully. Reattach the hot water supply hose, tightening securely by hand plus a partial turn with pliers — avoid overtightening plastic threaded fittings. While you're in there, it's also worth checking the hoses that run from the valve into the detergent dispenser drawer, since a loose or damaged hose at that connection can produce similar fill or leak symptoms. Restore the water supply and check for leaks before restoring power. Run a test cycle to confirm the washer fills normally with hot water. Tools needed: Phillips screwdriver, pliers, towel, work gloves. Frequently Asked Questions How do I know if it's the hot valve or the cold valve that's failed? Pay attention to which water temperature is affected. If the washer isn't getting hot water but cold-water fills work fine, this hot valve (W11168743) is the likely cause. If the opposite is true, the cold valve (W11168740) is more likely the issue. If both hot and cold fills are affected, or you're not sure, it's worth checking both valves before ordering. I have water dripping inside the tub when the washer isn't running. Is this the valve? Yes, likely one of the two inlet valves. A worn internal seal can let water seep through even when the valve should be fully closed, causing exactly this symptom. Since there are two valves (hot and cold) on this platform, you may need to inspect both to determine which one is leaking, or replace both if you're unable to isolate it. The valve and hoses look fine but water flow is still irregular. What else should I check? If the inlet screens are clear of obstruction and water flow is still weak or inconsistent, it's worth checking the hoses that run from the valve into the detergent dispenser drawer, since a kink, clog, or loose connection there can produce similar symptoms to a failing valve. Household water pressure and any inline filter screens are also worth ruling out. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and hose connection configuration of the hot water inlet valve originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

5220FR2006H Washer Hot Water Inlet Valve - Compatible with LG, Kenmore Product Description Ensure proper water flow with the replacement 5220FR2006H Washer Hot Water Inlet Valve. This replacement water inlet valve is designed for select LG and Kenmore front-load and top-load washers, featuring one solenoid to control hot water entry into the drum. It addresses issues like no water flow, leaks, improper filling, or error codes, offering a cost-effective alternative to OEM parts. Note: Includes one water inlet valve with one solenoid. Disconnect power and water supply before installation. Check water supply lines and valve filters for blockages to ensure optimal performance. Replaces part numbers: 5220FR2006H, 1268123, 5220FR1280F, 5220FR2006L, 5220FR2006Q, AH3527427, EA3527427, PD00001765, EAP3527427, AP4441935, PS3527427. Compatibility: Compatible with models including but not limited to: LG: WM2016CW, WM2077CW, WM2277HW, WM2455HW, WM2487HRM, WM2601HW, WM2701HV, WM2801HWA, WM3070HWA, WM3470HWA, WM8000HVA, WM9000HVA Kenmore: 796.40272800, 796.41022900, 796.41028900 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select LG and Kenmore front-load and top-load washers. 💧 Specifications: replacement water inlet valve with one solenoid, 120V, 60Hz. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires screwdriver, pliers, work gloves; typically installed in 20–30 minutes. 🛡️ Effective Fixes: Resolves no water flow, leaks, improper filling, or error codes. Product Specification Part Number: 5220FR2006H Component Type: Washer hot water inlet valve Material: High-grade plastic and metal Electrical Specs: 120V, 60Hz, one solenoid. Mounting: Screw-mounted near washer water inlet Operating Conditions: Suitable for high-pressure water supply environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the washer from the power source and water supply before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your washer running smoothly today! Add to cart now for a budget-friendly fix!

Read more less

WH13X26535 Genuine OEM GE Washer Water Valve The WH13X26535 is a genuine GE OEM water inlet valve assembly for GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café models. This valve controls the flow of hot and cold water into the tub during the fill portion of the cycle, ensuring each wash uses the correct amount of water at the right temperature blend. It's housed in durable gray plastic. Common failure causes include mineral or sediment buildup inside the valve body, a burned-out internal solenoid coil, and general wear over years of use — five years is a commonly cited service life before this valve starts to show problems. A failing valve produces a clear set of symptoms: the washer not filling properly, water continuing to fill or drip even when the washer is turned off, or leaking near the valve area. It directly replaces AP6892695, WH13X24386, 4931303, PS12726769, WH13X24392, WH13X26535-25PK, EAP12726769, and PD00052736. As a genuine OEM part, the WH13X26535 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance. Quick Answer The WH13X26535 Genuine OEM GE Washer Water Valve fixes GE top-load washers that aren't filling properly, are overfilling, or have water slowly dripping into the tub even when the washer is off. Housed in gray plastic. Replaces AP6892695, WH13X24386, 4931303, PS12726769, WH13X24392, WH13X26535-25PK, EAP12726769, PD00052736. This replacement valve does not include a thermistor or gasket — if your old valve has a thermistor mounted in front of the solenoids, you'll need to transfer it (with its gasket) to the new valve. Also not the same as the similarly-numbered WH13X26534, which is a separate valve for other GE/Hotpoint models. Common Problems This Part Fixes Washer not filling with water properly Washer overfilling Water slowly dripping or leaking into the tub even when the washer is turned off Leaking near the valve connections No hot water reaching the tub, or no cold water reaching the tub Cycle stalling at the fill step and never advancing to wash Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: WH13X26535, WH13X24386, WH13X24392, 4931303, 003C17, AGE26261, AP6892695, 4476388, 4931303, OEM20678094, EAP11729481, EAP12726769, K-78637-2, PD00052736, PS12726769. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café washers built on the GE platform, spanning model series GTW460, GTW465, GTW485, GTW490, GTW500, GTW525, GTW540, and VTW540, including specific model numbers such as 5TW4207ST0WS, 5TW4307SW0WS, ETW485ASW0WB, GTW460AMJ0WW, GTW460AMJ1WW, and GTW460AMJ2WW. Note — thermistor transfer required, and not the same as WH13X26534: This valve does not include a thermistor or the rubber gasket that seats it. If your original valve has a thermistor mounted in front of the solenoids, you must transfer that thermistor and its gasket onto this new valve during installation. Separately, this part is not the same as the similarly-numbered WH13X26534, a distinct valve used on other GE/Hotpoint models with its own cross-reference set (PS12726768, AP6891106). Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified solenoid design and housing Controls hot and cold water flow into the tub Resolves "won't fill properly," "overfilling," and "dripping into the tub when off" symptoms caused by valve failure Durable gray plastic housing Direct drop-in replacement — matches the original mounting and hose connections Replaces AP6892695, WH13X24386, 4931303, PS12726769, WH13X24392, WH13X26535-25PK, EAP12726769, and PD00052736 Compatible with GE, Hotpoint, Haier, Monogram, and Café top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Moderate DIY repair, typically 30 to 60 minutes Product Specifications Part Number WH13X26535 Part Type Washer Water Inlet Valve Condition Genuine OEM Application Top-Load Washers Housing Material Gray plastic Includes Thermistor/Gasket No — transfer from old valve if equipped Repair Difficulty Moderate — 30 to 60 minutes Quantity 1 valve Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Watch For The Thermistor O-Ring Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Access is typically behind the front control panel or top of the cabinet, depending on your model. The valve assembly is usually held in place with a metal plate and two screws. Photograph the wiring and hose connections before disconnecting anything. If your old valve has a thermistor (temperature sensor) mounted in front of the solenoids, it fits into a small hole in the bracket and uses an O-ring seal that's known to degrade and leak over time — this new valve does not include one, so you'll need to carefully transfer the thermistor and its gasket from the old valve to the new one. Disconnect the electrical connector and outlet hoses from the old valve, remove its mounting screws, and pull it free. Transfer the thermistor and gasket to the new WH13X26535 if applicable, then install it in the same position, reconnect all outlet hoses to their original positions, reconnect the electrical connector, and secure the mounting screws. Reattach the hot and cold supply hoses, tightening securely. Restore the water supply and check every connection for leaks before restoring power. Run a full test cycle across a few different temperature settings to confirm each fill function works correctly with no leaking. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions Does this valve come with the thermistor? No. This valve no longer comes with the rubber gasket or thermistor that some GE washers use, mounted directly in front of the solenoids. If your old unit has one, you'll need to remove it from the old valve, along with its gasket, and transfer it onto this new valve during installation. Water has been slowly leaking into my tub even when the washer is off. Is that this valve? Yes, this is a documented cause. One customer traced over a year of slow leaking directly to this valve's thermistor O-ring, which is known to degrade over time and let water seep through even when the washer isn't running. Replacing the valve (and transferring a good thermistor and gasket if your model uses one) resolves this type of slow leak. Is this the same as WH13X26534? No, these are two separate GE valve part numbers with different cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close number match. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, housing, and connection type of the water inlet valve originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH13X10024 Genuine OEM Washer Water Valve Replaces Part Numbers: WH13X10024, WH13X0086, WH13X0087, WH13X10004, WH13X10019, WH13X86, WH13X87, AH1155105, EA1155105, OEM15444478, AP3861119, PS1155105. Description: This Water Inlet Valve is a Genuine OEM part for select GE washing machine models. This component is crucial for controlling the flow of water into the washer during the wash and rinse cycles. It works by opening and closing the solenoids to allow the appropriate amount of hot or cold water to enter the washing machine, based on the selected settings.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

241798231 Genuine OEM Frigidaire Refrigerator Ice Maker The 241798231 is a genuine Frigidaire OEM ice maker assembly for Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse refrigerators. This 8-cube ice maker receives water from the refrigerator's water inlet valve, holds it in a mold, and freezes it into cubes. Once frozen, an internal mechanism ejects the cubes into the ice bucket below, and the cycle repeats automatically until the bucket is full — at which point a bail arm or sensor tells the ice maker to stop producing more. This assembly ships complete with its cover, wire harness, bail arm, and installation hardware, terminating in a 5-pin connector for a direct plug-in fit. Measuring approximately 11-3/4"L x 4-5/8"W x 4-3/4"H, with a harness and plug that run about 18" and a bail arm measuring 9-3/8"L x 1/8"W x 4-1/8"H. Over time, the plastic mold where the ice cubes actually form can flake, crack, or corrode, and internal mechanical components can wear out or fail electrically. If your ice maker's mold shows flaking or corrosion, or the unit has simply stopped producing ice, it's time for a new assembly rather than attempting a partial repair. It directly replaces AP6332951, 3206327, 3206329, 241642501, 241642503A, 241642511, 241798201, 241798209, 241798211, 241798220, 241798223, 241798224, 5303320545, 5304445222, 5304456669, 5304456671, 5304456672, EAP12364147, PD00044512, PS12085911, and PS12364147. Quick Answer The 241798231 Genuine OEM Frigidaire Refrigerator Ice Maker fixes Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse refrigerators that have stopped making ice, or where the ice mold is visibly flaking or corroded. 8-cube ice maker with cover, wire harness, bail arm, and installation hardware included. 5-pin connector. Replaces AP6332951, 3206327, 3206329, 241642501, 241642503A, 241642511, 241798201, 241798209, 241798211, 241798220, 241798223, 241798224, 5303320545, 5304445222, 5304456669, 5304456671, 5304456672, EAP12364147, PD00044512, PS12085911, PS12364147. This is not a universal part — always verify your exact model number before ordering. Common Problems This Part Fixes Ice maker has stopped producing ice entirely Ice maker producing far less ice than it used to Ice mold visibly flaking, cracking, or corroded Ice cubes coming out misshapen, small, or inconsistent Ice maker cycling but never ejecting cubes into the bucket Ice maker that runs constantly without ever reaching a full bucket and stopping Ice maker that hums or makes noise but doesn't complete a cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator ice maker directly replaces the following OEM and cross-reference part numbers: 241798231, 241798224, 5304456672, 241798201, 5304456671, 241642501, 241642503A, 241642511, 241798209, 241798211, 241798220, 3206327, 3206329, 4591526, 5303320545, 5304445222, 5304456669, 75304445222, 75304456669, 75304456671, 75304456672, AP6332951, AFR14980, PD00044512, PS12364147. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This ice maker is compatible with select Frigidaire refrigerators, and also fits select Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse refrigerators built on the same platform, including model numbers such as FFSS2315TS0. Note — not a universal part: This ice maker is model-specific despite the broad cross-reference list above. Always verify your full model number before ordering rather than assuming fit based on a general brand match. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified mold design and cycling mechanism Complete assembly — includes cover, 4-wire harness, bail arm, and installation hardware Produces 8 radius ice cubes per cycle Resolves "not making ice," "flaking or corroded mold," and "misshapen cubes" symptoms caused by ice maker failure 5-pin connector for a direct plug-in electrical fit Dimensions: 11-3/4"L x 4-5/8"W x 4-3/4"H; harness/plug approx. 18"L; bail arm 9-3/8"L x 1/8"W x 4-1/8"H Direct drop-in replacement — no modification required Replaces AP6332951, 3206327, 3206329, 241642501, 241642503A, 241642511, 241798201, 241798209, 241798211, 241798220, 241798223, 241798224, 5303320545, 5304445222, 5304456669, 5304456671, 5304456672, EAP12364147, PD00044512, PS12085911, and PS12364147 Compatible with Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 241798231 Part Type Refrigerator Ice Maker Assembly Condition Genuine OEM Brand Frigidaire Ice Output 8 radius cubes per cycle Kit Contents Ice maker, cover, 4-wire harness, bail arm, installation hardware Electrical Connector 5-pin Color White / Black / Gray Material Plastic / Metal Dimensions 11-3/4"L x 4-5/8"W x 4-3/4"H Harness/Plug Length Approx. 18" Bail Arm Dimensions 9-3/8"L x 1/8"W x 4-1/8"H Quantity 1 ice maker assembly Compatible Brands Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, Westinghouse Installation Notes ⚠️ Unplug Refrigerator And Shut Off Water Supply Before Starting Disconnect power at the outlet and shut off the water supply to the refrigerator before beginning. Wear work gloves. Open the freezer door and locate the ice maker assembly, typically mounted to the freezer wall or door depending on your model. Remove the ice bucket to improve access. Photograph the wiring harness connection before disconnecting anything. Remove the mounting screws securing the ice maker to the wall, then disconnect the wire harness connector and any water line connection feeding the unit. Remove the old ice maker fully. Install the new 241798231 assembly in the same mounting position, reconnect the wire harness connector, and reconnect the water line if applicable. Secure the mounting screws, reinstall the ice bucket, and restore the water supply and power. Allow several hours for the first cycle to complete and confirm ice is being produced and ejected into the bucket normally. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My ice maker's mold looks flaky or corroded. Should I replace the whole assembly? Yes. The ice mold is not a separately serviceable component on this assembly — if it's flaking, cracking, or corroded, that's a sign the assembly has reached the end of its service life and the complete unit should be replaced rather than repaired. My ice maker runs but never stops, or never seems to sense a full bucket. What does that mean? This can point to a failure in the bail arm or the internal sensing mechanism that tells the ice maker the bucket is full and it's time to pause production. Since the bail arm is included with this complete assembly, replacing the whole unit resolves this along with any other underlying cycling issues, rather than trying to source and repair that mechanism separately. The listing says this isn't a universal part even though it has a long cross-reference list. What does that mean for me? The long list of replaced part numbers reflects that this same physical assembly has been sold under many different numbers over the years and across related brands (Electrolux, Kenmore, Crosley, and others built on the same Frigidaire platform) — it does not mean this ice maker fits every refrigerator. Always confirm your specific model number before ordering, since visually similar ice makers can differ in ways that affect fit. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It includes the same mold design, wire harness, bail arm, and mounting configuration as the ice maker assembly originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

ADQ73613403 Refrigerator Water Filter Description: This water filter is designed to remove impurities from the water and ice dispensed by your refrigerator, providing clean and fresh-tasting water. It effectively reduces contaminants such as chlorine, lead, mercury, and other particulates, ensuring safe drinking water for you and your family.  You should replace this water filter if it becomes clogged or reaches the end of its usable life, typically every six months. Causes of a bad water filter can include normal usage leading to clogging, the accumulation of sediments and impurities over time, or damage to the filter casing. Failing to replace the filter regularly can also compromise its effectiveness. Cross Reference Number: ADQ73613403, AP6889636, PS12724756, LT800P/PC/PCS

Read more less

ERP 5220FR2008C - 5220FR2006H Washer Water Valve Set Hot & Cold Side Water Valves ERP 5220FR2008C (Cold Side 4 Ports) Replaces Part Numbers:5220FR2008C, 1345045, AH3527429, EA3527429, AP4441122, PS3527429 ERP 5220FR2006H (Hot Side) Replaces Part Numbers: 5220FR2006H, 1268123, 5220FR1280F, 5220FR2006L, 5220FR2006Q, AH3527427, EA3527427, AP4441935, PS3527427 This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO Washer Replacement Part XPARTCO 5220FR2075V Washer Water Valve Replaces 5221ER1003M Three-solenoid, DC12V water inlet valve assembly for select LG-built front-load washing machines. Product Overview The XPARTCO 5220FR2075V Washer Water Inlet Valve controls the flow of water entering compatible front-load washing machines. When energized by the washer control, the valve opens the required water path and directs water through the dispenser and into the tub. This is a new XPARTCO aftermarket replacement part designed to replace compatible LG inlet valve assemblies, including part number 5221ER1003M. Quick Answer XPARTCO 5220FR2075V is a three-solenoid, DC12V washer water inlet valve for select LG and LG-built Kenmore front-load washers. It replaces 5221ER1003M. Verify the complete washer model number, valve configuration, electrical connectors, and hose outlets before ordering. Common Problems This Part May Fix Washer does not fill with water Slow or restricted water filling Water continues entering after the washer is turned off Leaking from the inlet-valve area Incorrect water flow through the dispenser IE or another water-inlet-related error One or more valve solenoids do not open Replaces and Cross-References 5220FR2075V, ALG312873, AP7003066, PD00074485, PS16544738, 5221ER1003M, AP6334246, 4869495, ALG51888, EAP12579227, PD00050119, PS12579227 Cross-reference numbers help identify the compatible component. XPARTCO is an aftermarket replacement brand and is not manufactured by LG. Compatibility Designed for select LG and LG-built Kenmore front-load washers that specify 5220FR2075V, 5221ER1003M, or an approved equivalent. Compatible model examples associated with this valve family.  Important: This is only a partial compatibility list. LG water valves can look nearly identical while using different voltages, solenoid counts, mounting tabs, connectors, or outlet arrangements. Confirm the full washer model and original valve number before purchase. Key Features High-quality XPARTCO aftermarket replacement Replaces LG valve number 5221ER1003M DC12V, Three-solenoid inlet valve design Controls water entering the washer Directs water through the dispenser system Threaded inlet connection for the supply hose Designed for select LG-built front-load washers Product Specifications XPARTCO Part Number 5220FR2075V Replaces 5221ER1003M Brand XPARTCO Part Type Washer Water Inlet Valve Assembly, DC12V, 3 solenoid. Condition New Part Quality Aftermarket Replacement Valve Configuration Three Solenoids, DC12V Application Front-Load Washing Machine Included One Water Inlet Valve Assembly Installation Notes Unplug the washer and close both water-supply valves. Disconnect the inlet hose and prepare for residual water. Remove the washer top panel according to the appliance service procedure. Photograph the electrical connectors and outlet-hose locations before disconnecting them. Release the wire connectors, hose clamps, and mounting screws from the original valve. Install the replacement valve in the same orientation and reconnect every hose and wire. Open the water supplies slowly, check for leaks, restore power, and test the washer. Diagnostic tip: Confirm that the household water valves are open, inlet hoses are not kinked, and the inlet screens are not clogged before replacing the valve. Frequently Asked Questions Is XPARTCO 5220FR2075V a Genuine OEM LG part? No. It is an XPARTCO aftermarket replacement designed for compatible LG-built washers. What does the water inlet valve do? It opens and closes electrically to control water entering the washer and directs water through the dispenser system. Does this valve replace 5221ER1003M? Yes, this XPARTCO valve is sold as a replacement for 5221ER1003M on compatible washer models. Can a bad inlet valve cause an IE error? Yes. A failed solenoid, restricted valve, clogged inlet screen, or water-supply problem can cause slow filling or an inlet-related error. Will this fit every LG washer? No. Confirm the complete model number and compare the original valve number, connectors, mounting points, and hose outlets before ordering. Shop With Confidence Verify your washer model and original valve number before ordering. Our compatibility support team can help determine whether XPARTCO 5220FR2075V is correct for your appliance. XPARTCO Replacement PartFast U.S. ShippingCompatibility SupportSecure Checkout

Read more less

XPARTCO DD62-00084A Dishwasher Water Valve – Compatible with Samsung Dishwashers Product Description Restore proper water flow and reliable cleaning performance with the XPARTCO DD62-00084A Dishwasher Water Valve. This Dishwasher Water Valve is an essential component for maintaining the optimal performance of your dishwasher. This replacement part ensures precise water flow control, allowing your dishwasher to operate efficiently and effectively. A faulty water valve can cause no water entering the dishwasher, slow filling, or poor cleaning performance. Replacing it with this dependable XPARTCO valve helps restore consistent water flow and efficient operation. XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and function. Replaces Part Numbers DD62-00084A, 2692215, ASM36078, EAP4222448, PD00002158, 737534554937, OEM15534663, AP5178218, PS4222448 Compatibility This replacement dishwasher water inlet valve fits select Samsung dishwashers. Common compatible models include (but are not limited to): Samsung DW80F600UTS Samsung DW80J3020US Always verify your dishwasher’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and water flow performance 💧 Accurate Water Fill Control – Ensures proper water levels for effective cleaning ⚙️ Fixes Common Issues – Resolves no-fill or slow-fill problems 💪 Durable Solenoid Valve – Designed for reliable long-term use 💰 Cost-Effective Repair – Affordable alternative to OEM valves ⚠️ Symptoms If your dishwasher is experiencing any of the following issues, this part may need replacement: ❌ Dishwasher not filling with water 💧 Slow or weak water flow ⚠️ Poor cleaning performance due to low water level 🔄 Cycle not starting properly 🚫 No water entering during wash cycle Replacing this water valve can restore proper dishwasher operation and cleaning efficiency. 📐 Product Specification Part Number: XPDD62-00084A Component Type: Dishwasher Water Inlet Valve Voltage: 120V AC Application: Dishwasher water supply system Mounting: Screw-mounted with hose connection Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, adjustable wrench ⚠️ Safety First: Disconnect power and shut off the water supply before servicing the dishwasher. Basic Steps: Turn off power and water supply. Remove the lower access panel. Disconnect water supply line and electrical connector. Remove mounting screws and remove the old valve. Install the new XPARTCO DD62-00084A valve. Reconnect water line and wiring. Restore power and water, then test for leaks and proper filling. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore reliable dishwasher performance — Add to Cart Now for a dependable repair!

Read more less

XPARTCO WR51X10055 Refrigerator Defrost Heater Assembly The XPARTCO WR51X10055 is an aftermarket replacement refrigerator defrost heater and bracket assembly compatible with a wide range of GE, Hotpoint, Kenmore, Haier, Americana, Monogram, and Café refrigerators. The defrost heater is a glass quartz tube heater mounted on a bracket below the evaporator coils in the freezer compartment. During each automatic defrost cycle, the heater energizes and melts any frost that has accumulated on the evaporator coils — maintaining unobstructed airflow through the coils so the refrigerator can cool efficiently. When the heater fails, frost accumulates on the coils unchecked, blocking airflow and causing both the freezer and fresh food sections to gradually warm up. Rated at 120V, 725W, this single quartz tube heater assembly measures 12-1/8" L x 3-3/8" W x 2-1/8" H and includes the heater element and mounting bracket. It directly replaces WR51X10030, AP3183311, 914088, AH303781, EA303781, PS303781, SH323, and EAP303781. Often replaced together with the defrost thermostat (WR50X10068) and temperature sensor (WR55X10025) for a complete defrost system repair. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO WR51X10055 Refrigerator Defrost Heater Assembly fixes GE and Hotpoint refrigerators where frost is building up on the evaporator coils, the freezer is too warm, the fresh food section is warming up, or the refrigerator is running continuously without cooling properly. Single quartz tube heater, 120V / 725W. Assembly measures 12-1/8" L x 3-3/8" W x 2-1/8" H. Includes heater and bracket. Replaces WR51X10030, AP3183311, 914088, SH323, and more. Compatible with GE, Hotpoint, Kenmore, Haier, Americana, Monogram, and Café. Common Problems This Part Fixes Frost or ice buildup covering the evaporator coils in the freezer compartment Freezer section warming up or not maintaining set temperature Fresh food section warming up even though the freezer is running Refrigerator running continuously but not cooling properly Visible frost accumulation on the freezer back wall behind the panel Defrost heater element visibly burned out, broken, or dark/charred at the ends Both compartments gradually warming up after working normally for years Replaces Part Numbers This defrost heater assembly directly replaces the following OEM and cross-reference part numbers: WR51X10055, WR51X10030, 914088, AGE29323, AH303781, AP3183311, EA303781, EAP303781, PD00001004, PS303781. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This defrost heater is compatible with select refrigerators from the following brands: GE refrigerators (side-by-side, French door, top-freezer, and bottom-freezer) Hotpoint refrigerators Kenmore / Sears refrigerators (select GE-built models) Haier refrigerators (select GE-platform models) Americana refrigerators Monogram refrigerators Café refrigerators Tip: When replacing the defrost heater, it is highly recommended to also replace the defrost thermostat (WR50X10068) and temperature sensor (WR55X10025) at the same time. These three parts form the defrost system and are commonly replaced together — replacing all three prevents a second disassembly if another component fails soon after. Key Features Single quartz tube glass heater — melts frost from the evaporator coils during each automatic defrost cycle, maintaining airflow and cooling efficiency Rated 120V / 725W — correct electrical specifications for compatible GE refrigerators Assembly dimensions: 12-1/8" L x 3-3/8" W x 2-1/8" H — direct fit into the evaporator coil bracket Includes heater element and mounting bracket — complete assembly ready to install Replaces WR51X10030 and WR51X10055 — both older and current part numbers covered Compatible with GE, Hotpoint, Kenmore, Haier, Americana, Monogram, and Café refrigerators Often replaced together with WR50X10068 defrost thermostat and WR55X10025 temperature sensor Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WR51X10055 Also Replaces WR51X10030 Part Type Refrigerator Defrost Heater and Bracket Assembly Condition Aftermarket Replacement Heater Type Single quartz tube glass heater Voltage 120V AC Wattage 725W Dimensions 12-1/8" L x 3-3/8" W x 2-1/8" H Includes Heater element and mounting bracket Often Replaced With WR50X10068 Defrost Thermostat, WR55X10025 Temperature Sensor Compatible Brands GE, Hotpoint, Kenmore, Haier, Americana, Monogram, Café Installation Notes ⚠️ Unplug Refrigerator Before Starting — Wear Work Gloves Unplug the refrigerator before beginning. Remove all food and shelving from the freezer compartment. Remove the freezer bottom drawer and the back panel screws (typically 2 hex-head screws). Slide out the back panel to expose the evaporator coils and defrost heater assembly. If the coils are covered in frost or ice, use a hair dryer to melt the ice before removing the heater — do not chip or force the heater free while iced over, as the glass element is fragile and will break. Disconnect the heater wires from the wiring harness — note the orientation before disconnecting. Remove the 2 Phillips screws securing the heater bracket and lift the heater assembly out. Install the new WR51X10055 heater assembly in the same position, reconnect the wires, and reinstall the bracket screws. Reinstall the back panel, shelving, and food. Restore power and verify the defrost cycle operates normally. Wear work gloves throughout — the evaporator area has sharp edges. Tools needed: Phillips screwdriver, 1/4" nut driver, hair dryer (if coils are iced over), work gloves. Frequently Asked Questions What does the refrigerator defrost heater do? Modern refrigerators use an automatic defrost system that periodically runs a defrost cycle — typically once or twice a day — to melt frost that accumulates on the evaporator coils during normal operation. The defrost heater is a glass quartz heating element that energizes during this cycle and melts the frost off the coils. This keeps the coils clear so air can flow freely through them to cool the refrigerator. When the heater fails, frost builds up unchecked on the coils over days or weeks — eventually blocking airflow completely and causing both compartments to warm up, even though the compressor is still running. How do I know if my defrost heater has failed? Remove the freezer back panel to expose the evaporator coils. If the coils are heavily coated in frost or solid ice — especially if both the freezer and refrigerator sections have been warming up — a failed defrost heater is the most likely cause. You can confirm with a multimeter: disconnect the heater and probe both wire ends. A working heater shows continuity (resistance between approximately 10–200 ohms at room temperature depending on wattage). No continuity confirms the heater element has burned out. Also visually inspect the glass tube — a burned, blackened, or broken tube is a clear sign of failure. Should I also replace the defrost thermostat and temperature sensor? Yes — since the freezer must be fully emptied and the back panel removed to replace the heater, it is highly recommended to also replace the defrost thermostat (WR50X10068) and temperature sensor (WR55X10025) at the same time. All three components form the defrost system and wear at similar rates. A failed thermostat or sensor can cause the heater to run too long or not at all — replacing all three in a single repair eliminates that risk and saves you from another complete freezer teardown in the near future. My freezer is warming up but the compressor is running — is it the defrost heater? It often is — but not always. A compressor that is running but not cooling can be caused by a failed defrost heater (frost blocking airflow), a faulty evaporator fan motor (air not circulating), a defrost thermostat or timer failure, or a sealed system problem (refrigerant leak or compressor issue). The easiest way to distinguish a defrost system failure from other causes is to open the freezer and check whether frost has built up on the back panel or coils. If yes, the defrost heater is the most likely culprit. If the coils are clear and the compressor is running, look at the evaporator fan or sealed system next. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured as a single quartz tube glass heater rated at 120V/725W to match the dimensions and performance of the original WR51X10055 defrost heater assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC62-30314V Washer Water Valve – Compatible with Samsung & Kenmore Washers Product Description Restore proper water filling and reliable washer performance with the XPARTCO DC62-30314V Washer Water Valve. This high-quality aftermarket replacement precisely controls hot and cold water flow into the washer during fill cycles. A faulty inlet valve can cause no-fill issues, slow filling, water leaks, or error codes. Replacing it with this durable XPARTCO valve helps restore correct water pressure and dependable wash operation. Replaces Part Numbers DC62-30314V, PD00054103, EAP11719664, AP5966634, 3992464, PS11719664. Compatibility This replacement washer water inlet valve fits select Samsung and Kenmore (Samsung-manufactured) washers. Example compatible models include (but are not limited to):Samsung WF45R6100AW, WF42H5000AWKenmore 592.49045, 592.49303 Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM fit and water-flow performance 💧 Accurate Water Control – Ensures proper filling during wash cycles 🔧 Durable Solenoid Design – Built for consistent operation and long service life 💰 Cost-Effective Repair – Reliable alternative to OEM pricing 🛡️ Fixes Common Issues – Resolves no-fill, slow fill, leaks, or water inlet errors 📐 Product Specification Part Number: DC62-30314V Component Type: Washer Water Inlet Valve Voltage: 120V AC Water Connections: Hot & Cold Material: Reinforced plastic body with metal solenoids Mounting: Rear cabinet direct-fit Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, pliers, towel or shallow pan ⚠️ Safety First: Unplug the washer and shut off the water supply before servicing. Steps: Disconnect power and turn off water supply. Remove the rear access panel. Disconnect inlet hoses and wiring harness. Remove mounting screws and take out the old valve. Install the new XPARTCO DC62-30314V valve and secure it. Reconnect hoses and wiring, restore water and power, and test for leaks. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore proper washer filling and dependable performance — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

W11168740 - W11168743 Washer Water Valve Set for W11127357 Cold and Hot Washer Water Inlet Valve Housing and Wire Harness not included. Fits Kenmore, Maytag, Whirlpool top load washer models. Replaces Part Number:W11168740, WPW10240949, W10240949, W10921514, AP6285450, PS12348073, W11127357, W11127357, W10678672, W10678676, W10849466, W10921581, W11085642, AP6261887, PS12347475, W11168743, WPW10240948, W10240948, W10921515, AP6327638, PS12348074. Description: This Water Inlet Valve set is a replacement part for specific Kenmore, Maytag, Whirlpool washing machine models. It controls the flow of water into the washer tub at designated stages in the washing process. Water enters through the valve inlet and is distributed to internal components like the detergent dispenser, water pipes, and sump hoses. Common causes of a bad valve can include mineral scale buildup inhibiting proper flow regulation over time, or cracks and leaks from wear and tear on rubber gaskets and seals.    This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less