Search results for "Washer Pulley"

4681EA2001T Genuine OEM LG Washer Drain Pump Motor The 4681EA2001T is a genuine LG OEM drain pump motor for LG and Kenmore front-load washers, and also fits washer/dryer combo units. This motor is responsible for removing water from the washer at the end of the wash and spin cycles, expelling it through the drain hose so the machine can move on to the next stage of the cycle. This part is the motor only — you'll reuse your existing pump housing. It includes the pump impeller, which is not sold separately. Rated 120V-127V, 60Hz, 85W, 1.4A, with a flow rate of 45L per minute. Measures approximately 6.57" x 4.29" x 3.5". As of April 2025, the design of this drain pump motor changed to a gray housing, replacing the earlier black housing — this is expected and doesn't affect fit or function. Common failure causes include a worn or seized motor and general electrical wear. Symptoms of a failing drain pump motor include the washer not draining, unusual noise during the drain cycle, an OE error code, or leaking near the pump if the motor fails while still under load. It directly replaces 4681EA2001D, 4681EA2001U, 4681EA2001N, 4681EA1007G, 4681EA1007D, LP2001T, AP5328388, 2003273, 1468049, DP040-038, EAP3523278, EAP3579318, and 5214FR4006L. Quick Answer The 4681EA2001T Genuine OEM LG Washer Drain Pump Motor fixes LG and Kenmore front-load washers (and washer/dryer combos) that aren't draining, are making unusual noise during the drain cycle, or are showing an OE error code. 120V-127V, 60Hz, 85W, 1.4A, 45L/min. Replaces 4681EA2001D, 4681EA2001U, 4681EA2001N, 4681EA1007G, 4681EA1007D, LP2001T, AP5328388, 2003273, 1468049, DP040-038, EAP3523278, EAP3579318, 5214FR4006L. This is the motor only — reuse your existing pump housing when installing. As of April 2025, the new housing color is gray instead of the older black; this is a normal design change and not a compatibility issue. Common Problems This Part Fixes Washer not draining — standing water left in the tub after a cycle Unusual noise during the drain cycle OE error code displayed on the control panel Washer taking longer than normal to drain Leaking near the pump area Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drain pump motor directly replaces the following OEM and cross-reference part numbers: 4681EA2001T, 4681EA1007G, 2003273, 4681EA1007D, 4681EA2001D, 4681EA2001N, 4681EA2001U, DP040-038, ALG51292, AH3579318, EA3579318, PD00001722, EAP3579318, AP5328388, PS3579318 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select LG front-load washers, and also fits select Kenmore Elite washers built on the LG platform, and washer/dryer combo units, including model numbers such as WM2101HW, WM3270CW, WM3431HS, WM3770HVA, WM3001HWA, WM8000HVA, WM8000HWA, WM2550HRCA, WM2550HWCA, GCW1069CS, WM3550HWCA, WM3070HRA, WM4070HVA, WM3070HWA, WM2350HRC, WM3360HVCA, WM2350HWC, GCW1069QS, WM2650HRA, WM3360HRCA, WM3360HWCA, WM3150HVC, WM2650HWA, WM2655HVA, WM3885HCCA, WM3150HWC, WM3885HWCA, WM2250CW, WM2450HRA, WM3987HW, WM3470HVA, WM3470HWA, LSWF388HVS, WM3550HVCA, WM2455HG, WM2277HB, WM2487HRMA, and Kenmore 79641072310. Note: Always verify your full model number before ordering, since LG uses several different drain pump designs across its washer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine LG OEM part — factory-specified motor design and impeller Pumps wastewater out of the tub through the drain hose Resolves "not draining," "unusual noise during drain," and "OE error code" symptoms caused by motor failure Includes pump impeller (not sold separately) Reuses your existing pump housing — motor only Rated 120V-127V, 60Hz, 85W, 1.4A, 45L/min flow rate Direct drop-in replacement matching the original mounting and connections Replaces 4681EA2001D, 4681EA2001U, 4681EA2001N, 4681EA1007G, 4681EA1007D, LP2001T, AP5328388, 2003273, 1468049, DP040-038, EAP3523278, EAP3579318, and 5214FR4006L Compatible with LG and Kenmore front-load washers and washer/dryer combo units Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 4681EA2001T Part Type Washer Drain Pump Motor Condition Genuine OEM Brand LG Application Front-Load Washers, Washer/Dryer Combos Voltage 120V-127V Frequency 60 Hz Wattage 85 W Amperage 1.4 A Flow Rate 45 L/min Dimensions Approx. 6.57" x 4.29" x 3.5" Housing Not included — reuse existing pump housing Housing Color (as of April 2025) Gray (previously black) Repair Difficulty Medium — 30 to 60 minutes Quantity 1 drain pump motor Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Have Towels Ready For Draining Water Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Lay towels down in front of the washer before starting, and have a pail ready. Remove the detergent drawer and check the drain filter (bottom lower left panel door) to confirm it's clean and the drain line isn't blocked before assuming the motor is at fault. Many customers find it easier to access the pump from underneath by carefully laying the washer on its back — be prepared for a significant amount of additional water to drain out onto the floor once you do this, so keep towels close by. With access to the pump, disconnect the electrical connector from the old motor and separate the motor from the pump housing, which you'll reuse with the new motor. Attach the new 4681EA2001T motor to your existing pump housing, transferring the impeller setup as needed. Reconnect the electrical connector fully. Stand the washer back upright, reinstall the detergent drawer, and reconnect the water supply and power. Test the new pump to confirm it drains properly before considering the repair complete. Tools needed: Phillips screwdriver, locking pliers, needle nose pliers, small flathead screwdriver, towels, work gloves. Frequently Asked Questions My washer shows an OE error code and isn't draining. Is this the part I need? Likely yes. An OE error code on LG washers is commonly tied to a drain issue, and a bad drain pump motor is one of the most frequent causes. Before replacing the motor, it's worth checking that the drain filter and coin trap (if your model has one) are clean and that the drain line itself isn't blocked, since those are simpler and cheaper things to rule out first. Does this come with the pump housing? No, this is the motor only, and it includes the pump impeller, which isn't sold separately. You'll reuse your existing pump housing during installation rather than replacing it as part of this repair. The new motor's housing looks a different color than I expected. Did I get the wrong part? No, this is expected. As of April 2025, LG changed the design of this drain pump motor to use a gray housing in place of the earlier black housing. This is a normal manufacturing update and doesn't affect fit or function. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original motor design, impeller, and electrical rating of the drain pump motor originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

AHA72973309 Genuine OEM LG Washer Drain & Circulation Pump Assembly The AHA72973309 is a genuine LG OEM drain and circulation pump assembly for LG and select Kenmore front-load washers. This is a dual-purpose pump — an Askoll M120-2 unit — that handles two separate jobs from one motor and housing. During the drain portion of the cycle, it pumps wastewater out of the tub and out through the drain hose. During the wash and rinse portions, it switches roles and recirculates water from the bottom of the tub back up through the dispenser and spray nozzle, showering it back over the load. That recirculation spray is what lets LG's front-load washers clean effectively with less water than an older top-load design would need. Because this single assembly performs both functions, a failure here can show up in more than one way: standing water left in the tub after a cycle, a washer that won't complete its drain step, unusual grinding or humming noise, or reduced wash performance if the recirculation spray isn't working even though draining still seems fine. Common causes include debris such as coins, buttons, or lint lodged in the impeller, general wear and tear on the motor bearings, or an electrical failure in the pump motor itself. It directly replaces AP5676608, 2659237, AHA72973304, and PS7788830. As a genuine OEM part, the AHA72973309 is manufactured by LG to factory specifications — guaranteed fit, materials, and performance. Quick Answer The AHA72973309 Genuine OEM LG Washer Drain & Circulation Pump Assembly fixes LG and select Kenmore front-load washers with standing water left in the tub after a cycle, a washer that won't drain, unusual grinding or humming noise, or reduced wash performance from a weak recirculation spray. Askoll M120-2 dual-purpose pump — handles both draining and mid-cycle water recirculation. Replaces AP5676608, 2659237, AHA72973304, PS7788830. Installation is average difficulty, 30 to 60 minutes — and on many models it's accessible through the front panel without needing to tip the washer over. Common Problems This Part Fixes Standing water left in the tub after a cycle finishes Washer won't drain, or drains very slowly Drainage-related error code displayed on the control panel Unusual grinding, humming, or rattling noise during the drain or wash portion of the cycle Reduced wash performance — clothes not getting as clean, possibly from a weak recirculation spray Washer stalling mid-cycle at the drain step Water leaking from underneath the washer near the pump housing Pump that hums but doesn't seem to move water — possible clog or seized impeller Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drain and circulation pump assembly directly replaces the following OEM and cross-reference part numbers: AHA72973309, AHA72973304, AP5676608, 2659237, ALG53336, PD00024680, PS7788830 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain and circulation pump assembly is compatible with select LG front-load washers, and also fits select Kenmore and Kenmore Elite front-load washers built on the LG platform. Note: This is a dual-function drain-and-circulation assembly specific to LG's front-load platform, built around the Askoll M120-2 pump. It is not a drain-only pump, and it is not intended for top-load washers, which use a different pump design. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine LG OEM part — factory-specified motor, impeller, and housing design Dual-purpose Askoll M120-2 pump — drains the tub and recirculates wash water through the dispenser spray nozzle Resolves "standing water in the tub," "won't drain," "grinding or humming noise," and "reduced wash performance" symptoms caused by pump failure Includes all necessary wiring and mounting hardware for a complete replacement Direct drop-in replacement — no modification required Replaces AP5676608, 2659237, AHA72973304, and PS7788830 Compatible with LG and select Kenmore/Kenmore Elite front-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Average installation difficulty — typically 30 to 60 minutes Product Specifications Part Number AHA72973309 Part Type Washer Drain & Circulation Pump Assembly Condition Genuine OEM Brand LG Pump Model Askoll M120-2 Function Drains tub water and recirculates wash water through the dispenser spray Kit Contents Pump assembly with wiring and mounting hardware Application Front-Load Washers (LG-Built) Repair Difficulty Average — 30 to 60 minutes Quantity 1 pump assembly Compatible Brands LG, select Kenmore, Kenmore Elite Installation Notes ⚠️ Unplug Washer And Shut Off Water Before Starting — Drain Residual Water First Disconnect power at the outlet or shut off the circuit breaker, and close the water supply valves before beginning. Wear work gloves. Place towels down and have a shallow pan ready, since the pump housing will hold residual water even after a completed cycle — draining this into a pan before disconnecting hoses will save you a mess. On many models, this pump is fully accessible by removing the front lower access panel or kick plate, without needing to tip the washer onto its back — check this first, since it can save significant time and effort compared to some online guides that recommend tipping the unit. Photograph the hose routing and wiring connections before disconnecting anything. Disconnect the two hose clamps connecting the pump to the tub and drain hose, and unplug the electrical connector from the pump motor. Remove the mounting screws or clips securing the pump assembly and lift it free, checking the impeller area for coins, buttons, or debris while it's out — clearing a clog here may have been the actual cause of the original symptom. Install the new AHA72973309 in the same orientation, reconnect both hoses with their clamps, and reconnect the electrical connector fully. Reinstall the front access panel, restore water and power, and run a short cycle to confirm normal draining, recirculation spray, and no leaks around the pump housing. Tools needed: Phillips screwdriver, hose clamp pliers, shallow pan or towels, work gloves. Frequently Asked Questions Do I really need to tip the washer over to replace this pump? Not necessarily — check your model first. While a lot of general online guidance recommends tipping the washer onto its back to access the pump from underneath, many LG and Kenmore Elite front-load models make this pump fully accessible through the front lower access panel or kick plate instead, without any tipping required. It's worth removing that panel first and seeing what you find before committing to the more involved tip-over approach. Why does this one pump handle both draining and something during the wash cycle? LG's front-load washers use this same Askoll pump for two different jobs at different points in the cycle: pumping wastewater out during the drain step, and recirculating water from the bottom of the tub back up through the dispenser and spray nozzle during wash and rinse to shower it over the load. That recirculation spray is part of how these washers clean effectively while using less water than an older top-load design. Because one pump does both jobs, a failure can affect draining, wash performance, or both, depending on what's actually gone wrong inside it. There's water left in the tub after every cycle. Is this definitely the pump? It's one of the most common causes, but check the easy things first. A clogged drain filter or a kinked drain hose can produce the same "won't drain" symptom and cost nothing to fix. If the filter and hose are clear and water is still standing in the tub, or if the pump hums but doesn't seem to move any water, the pump assembly itself has likely failed. My washer drains fine but clothes aren't coming out as clean. Could this pump be the cause? Possibly. Since this same assembly also handles the recirculation spray during wash, a partial failure can leave draining intact while weakening or eliminating that spray function, which reduces how effectively detergent and water reach the load. If drainage is normal but wash performance has noticeably declined, it's worth having this pump checked as one possible cause alongside things like detergent dosing and water hardness. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It includes the same Askoll M120-2 dual-function pump design, wiring, and mounting configuration as the drain and circulation pump assembly originally installed in your front-load washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH23X28418 Washer Genuine GE OEM Drain Pump The WH23X28418 is a Genuine GE OEM replacement drain pump and motor assembly compatible with select GE, Hotpoint, Haier, RCA, and Kenmore top-load and front-load washers. The drain pump removes water from the washer drum during the drain and spin cycles — expelling water and detergent through the drain hose so that clothing comes out clean and free of excess water. When the pump fails, the washer will not drain, may leave standing water in the tub, or may produce loud noises during the drain cycle. This complete drain pump and motor assembly is rated at 120V, 60Hz, 1.25A with a duty cycle of 10 minutes on and 50 minutes off. It includes the pump and motor with harness — the harness and plug extend approximately 10 inches from the motor. The pump measures 5-1/4" L x 5-1/8" W x 5-1/2" H and includes a drain pump seal. It directly replaces WH23X24178 and WH23X27574, as well as several additional cross-reference numbers. Installs in 20–40 minutes with basic hand tools. Quick Answer The WH23X28418 Washer Genuine GE OEM Drain Pump fixes GE, Hotpoint, Haier, and RCA washers that won't drain, leave standing water in the tub, are noisy during draining, or leak around the pump area. Complete pump and motor with harness and drain pump seal. 120V/60Hz/1.25A. Dimensions 5-1/4" L x 5-1/8" W x 5-1/2" H; harness extends approx. 10". Replaces WH23X24178 and WH23X27574. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Washer stopping mid-cycle due to a drain fault or drain-related error code Loud humming, grinding, or buzzing noise during the drain cycle Washer pumps but will not spin — pump failure preventing cycle completion Water leaking from around the drain pump area Clothes not clean or coming out soaking wet due to incomplete drainage Pump impeller jammed by debris causing motor burnout Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: WH23X24178, WH23X28418, WH23X27574, 290D1201G001, 290D1201G002, 290D1201G003, AGE26155, B40-3A01, B30-3A02, PD00055680, EAP12723115, AP6889136, PS12723115. WH23X28418 is the current updated part number replacing the discontinued WH23X24178 and WH23X27574. If your washer documentation or old pump label shows either of those numbers, this is the correct replacement. Compatibility This drain pump is compatible with select washers from the following brands and series: GE top-load washers — GTW220, GTW330, GTW335, GTW460, GTW465, GTW485, GTW490, GTW500, GTW680, GTW720, GTW725, GTW750 series and others GE front-load washers — select GFW series models Hotpoint top-load washers — HTW200, HTW240 series and others Haier top-load washers — select models RCA top-load washers — select models Kenmore / Sears washers — select GE-built models Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Removes water and detergent from the washer drum during drain and spin cycles Complete assembly — includes pump motor, harness, and drain pump seal Rated 120V, 60Hz, 1.25A with a 10-minute on / 50-minute off duty cycle Dimensions: 5-1/4" L x 5-1/8" W x 5-1/2" H; harness and plug extend approximately 10" from motor Plastic and metal construction rated CL.A — durable and chemical resistant Includes drain pump seal to prevent leaks at the pump connection Current updated replacement for discontinued WH23X24178 and WH23X27574 — direct fit Note: The drain pump motor has been redesigned by the manufacturer — the replacement may look different from the original but fits and functions identically Genuine GE OEM part — factory-exact fit, materials, and specifications DIY-friendly repair — installs in 20–40 minutes with basic hand tools Product Specifications Part Number WH23X28418 Supersedes WH23X24178, WH23X27574 (both discontinued) Part Type Washer Drain Pump and Motor Assembly Condition Genuine OEM Application GE, Hotpoint, Haier, RCA Top-Load and Front-Load Washers Voltage 120V AC Frequency 60 Hz Amperage 1.25A Rating CL.A Duty Cycle 10 minutes ON / 50 minutes OFF Dimensions 5-1/4" L x 5-1/8" W x 5-1/2" H Harness Length Approximately 10 inches from motor Color White / Black / Gray Material Plastic / Metal Includes Pump and motor with harness, drain pump seal Compatible Brands GE, Hotpoint, Haier, RCA, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Have towels and a shallow pan ready to catch residual water. For top-load GE washers, the drain pump is typically accessed from the bottom of the machine — carefully tilt the washer back onto a support or lay it on its side to reach the pump from underneath. Disconnect the outlet hose by loosening the hose clamp and pulling it free. Disconnect the electrical harness connector. Remove the mounting screws (typically three) securing the pump to the washer base. Twist and firmly pull the old pump out. Install the new WH23X28418 pump in reverse order — connect the hose, tighten the clamp, reconnect the harness, and secure the mounting screws. Restore power and water supply and run a test cycle to verify proper drainage and no leaks. Tools needed: Phillips screwdriver, flat-head screwdriver, slip-joint pliers, shallow pan. Frequently Asked Questions What is the relationship between WH23X28418, WH23X24178, and WH23X27574? All three are GE washer drain pumps — WH23X28418 is the current updated part number that replaced both the discontinued WH23X24178 and WH23X27574. GE redesigned the pump motor during its production cycle, so the replacement may look slightly different from the original, but it fits and functions identically. If your washer uses either of the older numbers, order WH23X28418. How do I know if my washer drain pump has failed? The most common signs are standing water in the tub after a cycle, the washer stopping mid-cycle with a drain error, or loud humming during the drain phase — which indicates the motor is running but the impeller is not moving. A grinding or rattling noise suggests debris in the pump or physical damage. If the pump is completely silent during what should be the drain cycle, the motor has likely burned out and the pump needs replacement. Does the WH23X28418 fit both top-load and front-load GE washers? The WH23X28418 is primarily used in GE and Hotpoint top-load washers — the GTW and HTW series make up the majority of compatible models. It also fits select GE front-load models. Always verify your specific model number before ordering to confirm compatibility for your washer type. What is the duty cycle rating and why does it matter? The duty cycle of 10 minutes on / 50 minutes off means the pump motor is rated for up to 10 consecutive minutes of operation before requiring a 50-minute rest period. In normal washer operation this is never an issue — drain cycles are brief. However, if a drain fault causes the pump to run continuously without successfully draining, the motor can overheat. If you replace the pump due to burnout and the new pump also fails quickly, check for a drain hose blockage or control board fault that may be causing the pump to run without limit. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications — the exact same drain pump and motor assembly installed in compatible models from the factory, with guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO DC97-20621C Washer Drain Pump Assembly The XPARTCO DC97-20621C is an aftermarket replacement drain pump assembly compatible with a wide range of Samsung front-load washers in the specific series, as well as select Kenmore front-load washers built on the Samsung platform. The drain pump removes water from the washer tub during the drain portion of each wash cycle. When the pump fails, the washer will not drain, leave standing water in the tub, stop mid-cycle, display error codes 5C, SE, nd, 5E, or 4E, or make loud grinding or humming noises during the drain phase. The DC97-20621C is the current production revision of this pump, which also covers the earlier DC97-20621A variants — all three are the same pump in successive production runs. It also replaces DC97-17999N, DC31-00187A, PX3516-01, AP6807020, 4959632, PS12592830, and EAP12592830. Before ordering, always check the drain filter/coin trap at the bottom front of the washer — a clogged filter is a common cause of drain error codes that does not require pump replacement. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DC97-20621C Washer Drain Pump Assembly fixes Samsung front-load washers displaying error codes 5C, SE, nd, 5E, or 4E, not draining, leaving standing water, or making loud grinding or humming noises during the drain cycle. Covers DC97-20621A and DC97-20621B variants. Compatible with select Samsung series and Kenmore (Samsung-built). Replaces DC97-20621A, DC97-17999N, DC31-00187A, PX3516-01, AP6807020, 4959632, PS12592830, EAP12592830. Check drain filter before replacing pump. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Error codes 5C, SE, nd, 5E, or 4E displayed — drain fault detected Washer stopping mid-cycle due to a drain fault Loud humming during the drain phase — pump motor running but not pumping Grinding or rattling noise during drain — damaged impeller or worn pump bearings Water draining very slowly — worn pump below rated performance Clothes excessively wet after a cycle — pump not fully removing water before spin Water leaking from the pump area at the front bottom of the washer Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: DC97-20621C, DC97-17999N, DC97-20621A, 03DC31-00187A, AP7366238, ASM105564, PFIX17701443, PD00095227, PX3516-01, PS17701443, AP6807020, PS12592830. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump is compatible with select Samsung front-load washers and related Kenmore models: Samsung series — WF50R8500AW, WF45T6200AW, WF53BB8900 and related models Kenmore / Sears front-load washers (select Samsung-built models) Important: Before replacing the pump, check and clean the drain filter/coin trap located behind the lower access panel at the front of the washer. A clogged filter causes the same error codes as a failed pump and is the most common fixable cause of Samsung front-load drain errors. Always verify your model number before ordering. Key Features Removes water from the tub during drain and spin cycles for proper washer operation Resolves Samsung error codes 5C, SE, nd, 5E, and 4E caused by drain pump failure DC97-20621C is the current production revision — covers DC97-20621A and DC97-20621B as well Also replaces DC97-17999N, DC31-00187A, PX3516-01, AP6807020, 4959632, PS12592830, and EAP12592830 Compatible with select Samsung series and Kenmore Samsung-built front-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number XPDC97-20621C Also Covers DC97-20621A (prior revisions) Part Type Front-Load Washer Drain Pump Assembly Condition Aftermarket Replacement Application Samsung Front-Load Washers  Error Codes Resolved 5C, SE, nd, 5E, 4E Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. Place towels on the floor in front of the washer — residual water will drain when the pump is disconnected. The drain pump is accessed through the lower front panel. Remove the lower kick panel screws to expose the drain filter and pump area. First, drain residual water by removing the drain filter cap (have a shallow pan ready — up to a quart of water may flow out). After draining, disconnect the pump wiring harness. Release the hose clamps and disconnect the drain hoses from the pump. Unscrew or unclip the pump mounting hardware and remove the old pump. Install the new DC97-20621C pump in the same position, reconnect drain hoses and secure clamps, reconnect the wiring harness, and reinstall the front panel. Restore power and water and run a drain/spin cycle to confirm drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan, towels. Frequently Asked Questions What is the difference between DC97-20621C and DC97-20621A? These are successive production revisions of the same Samsung front-load washer drain pump assembly. DC97-20621A was the original version, DC97-20621B was an intermediate revision, and DC97-20621C is the current production part. All three are the same pump with minor manufacturing changes across production runs — they are fully interchangeable. If your washer's parts diagram or old pump label shows any of these numbers, this replacement covers all of them. What error codes indicate a drain pump failure on Samsung front-load washers? Error codes 5C, SE, nd, 5E, and 4E on Samsung front-load washers all indicate a drain fault — the washer was unable to drain within the expected time. Before replacing the pump, clean the drain filter/coin trap at the front lower access panel — lint, coins, and debris in the filter are among the most common causes of these error codes. If the filter is clean and the errors persist, the pump itself has failed and needs replacement. Where is the drain filter on my Samsung front-load washer? The drain filter (also called the coin trap) on Samsung front-load washers is located behind the lower front access panel, typically on the right side. Remove the lower kick panel by pressing the release tab or removing the screws. You will see a small cap or twist-out cover — that is the filter. Place a shallow pan under it and slowly unscrew the cap to allow water to drain out. Remove any debris from the filter, then replace the cap and reinstall the panel. Run a cycle to check if the error clears. If the filter was clogged, this may be all the repair needed. My washer makes a loud noise during draining — is it the pump? A loud humming or grinding during the drain cycle is a common sign of a failing pump. Humming without water movement means the motor is running but the impeller is not pumping — either jammed by debris or mechanically failed. Grinding suggests worn pump bearings or a damaged impeller. Check the drain filter first for foreign objects. If the filter is clear and the noise persists, the pump needs replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the specifications and performance of the original DC97-20621C drain pump assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 661570 Dryer Drum Belt Replaces 661570V The XPARTCO 661570 is an aftermarket replacement dryer drum belt compatible with select Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Crosley, Admiral, and Speed Queen dryers. The drum belt wraps around the outside of the dryer drum, loops around the idler pulley and motor pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from high-strength rubber, this 4-rib belt measures 93-1/2 inches long x 1/4 inch wide x 1/8 inch high with 4 ribs and 3 grooves. It is a direct drop-in replacement for OEM part numbers 661570V and 661570, and is part of the 4392067 dryer repair kit. It pairs with the W10837240 idler pulley and WPW10314173 drum rollers for a complete drum drive overhaul. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 661570 Dryer Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is present during operation. Compatible with select Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Crosley, Admiral, and Speed Queen dryers. Measures 93-1/2" L x 1/4" W x 1/8" H with 4 ribs and 3 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Burning rubber smell coming from the dryer Visible broken or frayed belt pieces found inside the dryer cabinet Dryer shuts off shortly after starting due to drum not rotating Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: 661570V, 661570, 3387610, 3389728, 3393999, 339728, 4248258, 661570VP, AWP761693, OEM17951196, PD00023608, FIX382430, AP5983729, PS11722115. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Maytag dryers (gas and electric) Kenmore / Sears dryers (select Whirlpool-built models) Amana dryers KitchenAid dryers Crosley dryers Admiral dryers Speed Queen dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the idler pulley and motor pulley for smooth, consistent tumbling every cycle 93-1/2" length x 1/4" width x 1/8" height — 4-rib, 3-groove design for a secure, slip-free grip on the pulleys Made from high-strength rubber — resists cracking, stretching, heat damage, and oil Direct replacement for OEM part numbers 661570V and 661570 — no modification required Part of the 4392067 dryer repair kit — pairs with W10837240 idler pulley and WPW10314173 drum rollers Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number 661570 OEM Part Number 661570V Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Gas and Electric Dryers Length 93-1/2 inches Width 1/4 inch Height 1/8 inch Ribs 4 ribs, 3 grooves Material High-strength rubber Color Black Compatible Brands Whirlpool, Maytag, Kenmore, Amana, KitchenAid, Crosley, Admiral, Speed Queen Part of Kit 4392067 Dryer Repair Kit Often Replaced With W10837240 Idler Pulley, WPW10314173 Drum Rollers Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen and unscrew the Phillips screws inside the lint screen housing. Use a putty knife to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release the belt from the idler pulley, lift the drum slightly, and slide the old belt off. Loop the new 661570 belt around the drum with the ribbed side facing inward toward the drum. Route the belt around the idler pulley and motor pulley — consult your dryer's service manual or a model-specific repair video for the correct belt path. Reassemble and run a test cycle. Tip: While the drum is out, inspect and replace the idler pulley (W10837240) and drum rollers (WPW10314173) if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions What is the difference between 661570 and 661570V? These are the same belt. 661570V is the updated OEM part number (the "V" denotes the current version) that superseded the original 661570. Both numbers refer to the identical drum belt — this aftermarket replacement is compatible with both. How does the 661570 differ from the 341241 and W10205415 belts? All three are Whirlpool-family dryer drum belts, but they differ in length, width, and rib count. The 661570 is 93-1/2" long x 1/4" wide with 4 ribs and 3 grooves. The 341241 is 92-1/4" long x 1/4" wide with 4 ribs and 3 grooves. The W10205415 is 92" long x 3/8" wide with 5 ribs and 4 grooves. They are not interchangeable — always use the part number specific to your dryer model. How do I know if my drum belt is broken? The most obvious sign is that the dryer motor hums but the drum does not spin. You may also notice a thumping or slapping sound, a burning rubber smell, or damp clothes after a full drying cycle. Open the dryer cabinet to visually confirm if the belt is broken, frayed, or stretched out of shape. Should I also replace the idler pulley and drum rollers? Yes — since the dryer is already disassembled, it is highly recommended to inspect and replace the idler pulley (W10837240) and drum support rollers (WPW10314173) at the same time. All three parts wear together and are sold together in the 4392067 dryer repair kit. Replacing all three prevents having to disassemble the dryer again in the near future. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is made from high-strength rubber to match the dimensions and performance of the original 661570V belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

Genuine Whirlpool WPW10250667 Washer Counterweight Spring - Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Estate, Inglis Product Description Stabilize your washer with the Genuine Whirlpool WPW10250667 Washer Counterweight Spring. This OEM suspension spring is designed for select Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Estate, and Inglis top-load washers, supporting the tub to absorb vibrations and maintain balance during wash and spin cycles. Made of high-quality stainless steel, it ensures long-lasting performance, addressing issues like excessive shaking, banging noises, or unbalanced loads. Note: Includes one counterweight spring. Disconnect power before installation. For even wear, replace all suspension springs at the same time. Replaces part numbers: WPW10250667, W10250667, 338492, 388492, 388492D, 62738, 63207, PD00002693, EAP11751118, AP6017818, PS11751118, WPW10250667VP Compatibility: Compatible with models including but not limited to: Whirlpool: LSQ8243HQ0, LSQ8512KQ0, LSQ8543JQ0, LSQ8543JQ1, LSQ8543JT0, LSQ8543JT1 Kenmore: 11010502990, 11010502991, 11016602690, 11018202790, 11018522790, 11018532790, 11018542890, 11018542891, 11018609890, 11018702790, 11018702791 Maytag, KitchenAid, Roper, Estate, Inglis: (select top-load models, verify compatibility) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Estate, and Inglis top-load washers. ⚖️ Specifications: OEM stainless steel counterweight spring, designed for optimal vibration absorption. 💪 Reliable Performance: Authentic Whirlpool part ensures superior durability and performance. 🛠️ Easy Installation: Requires pliers and a helper to tilt the washer; typically installed in 10–15 minutes. 🛡️ Effective Fixes: Resolves excessive shaking, banging noises, or unbalanced loads during operation. Product Specification Part Number: Genuine Whirlpool WPW10250667 Component Type: Washer counterweight (suspension) spring Material: Stainless steel Mounting: Hook-mounted to washer tub and frame Operating Conditions: Suitable for household top-load washer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the washer from the power source before installation. Shop for high-quality Genuine appliance parts with a 30-day return policy. Keep your washer running smoothly today! Add to cart now for a reliable fix!

Read more less

W11210459 Genuine OEM Whirlpool Washer Water Inlet Valve The W11210459 is a genuine Whirlpool OEM water inlet valve for Whirlpool top-load washers, and also fits select Kenmore, Maytag, Amana, Crosley, Inglis, and Roper models. This valve controls the flow of hot and cold water into the tub during the fill portion of each cycle — an electrical solenoid opens and closes the valve to admit exactly the right amount of water for the selected wash setting. Over time, mineral or sediment buildup inside the valve, or general wear in the solenoid coil, can cause the valve to fail. A failing valve typically shows up as the washer not filling with water, filling very slowly, or water continuing to leak into the tub after the wash has completed. It directly replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, and W11210459VP. Quick Answer The W11210459 Genuine OEM Whirlpool Washer Water Inlet Valve fixes Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, and Roper top-load washers that won't fill, fill very slowly, or continue leaking water into the tub after the wash has finished. Replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, W11210459VP. The control panel can be removed more easily with a putty knife slid under each end to release the clips, rather than removing the back panel first. Common Problems This Part Fixes Washer not filling with water Washer filling very slowly Water continuing to leak into the tub after the wash cycle has completed No hot water reaching the tub, or no cold water reaching the tub Cycle stalling at the fill step and never advancing to wash Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: W11210459, W10701459, W10838319, W11038711, 4591321, W10869799, W11025984, 33190189, 33190190, W10423122, W10423124, W10868380, W10868381, AP6329217, AWP43369, EAP12349267, OEM18987660, PD00042885, PS12349267 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select Whirlpool top-load washers, and also fits select Kenmore, Maytag, Amana, Crosley, Inglis, and Roper washers built on the Whirlpool platform, including model numbers such as WTW5000DW1 and WTW4816FW2. Note — not the same as W11210463: A similarly-numbered valve, W11210463 (also cross-referenced as W11101906), is a separate part with its own cross-reference set (W10701461, W10883458, W10869803, W11038696, AP6329219), used on other Whirlpool washer models. The two are easy to confuse given how close the numbers are — always confirm you have the exact part number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate Regulates hot and cold water flow into the washer tub Resolves "won't fill," "fills slowly," and "leaks after cycle completes" symptoms caused by valve failure Factory Certified Part built to Whirlpool's engineering specifications Direct drop-in replacement — matches the original mounting and hose connections Replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, and W11210459VP Compatible with Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, and Roper top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Moderate DIY repair Product Specifications Part Number W11210459 Part Type Washer Water Inlet Valve Condition Genuine OEM Brand Whirlpool Application Top-Load Washers Function Controls hot and cold water flow into the tub Repair Difficulty Moderate Quantity 1 valve Compatible Brands Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, Roper Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Use A Putty Knife To Release The Control Panel Disconnect power at the outlet, or shut off the house circuit breaker for the appliance, and shut off both hot and cold water supplies before beginning. Wear work gloves. The top control panel can be removed more easily by sliding a putty knife under the panel on each end to release the retaining clips, rather than removing the back panel first — one customer specifically noted this trick saved considerable time after trying the back-panel approach without success. With the panel released, locate the water inlet valve and photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the hot/cold water lines from the old valve, remove its mounting screws, and pull it free. Install the new W11210459 in the same position, reconnect the water lines and electrical connector fully, and secure the mounting screws. Reinstall the control panel. Restore the water supply and power, then run a full test cycle across a few temperature settings to confirm correct fill behavior with no leaking. Tools needed: multi-screwdriver, putty knife, work gloves. Frequently Asked Questions My washer isn't filling with water. Is this the right part? Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the washer, a solenoid failure or internal blockage can prevent any water from entering at all, stopping the wash cycle from proceeding. What's the easiest way to access the control panel for this repair? Try sliding a putty knife under the panel at each end to release the retaining clips, rather than removing the back panel of the washer first. One customer specifically learned this trick after trying the back-panel approach with no luck, then found the putty knife method worked cleanly after watching an online tutorial. Is this the same as W11210463? No, these are two separate Whirlpool valve part numbers with different cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close number match. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WPW10352973 Washer Genuine Dispenser Actuator Dispenser Drawer Switch Actuator for Washer Replaces Part Numbers: WPW10352973, W10352973, W10065190, W10163975, W10283468, 8183186, AP6020256, PS11753574. ✅ Product Description: Restore proper detergent dispensing with this genuine OEM WPW10352973 washer dispenser actuator. Designed to control the flow of detergent and fabric softener into your wash cycle, this part is a direct replacement for worn or non-functioning actuators in many Whirlpool, Maytag, Amana, Kenmore, and Crosley top-load washing machines. Part Features: Genuine OEM quality – built to factory specs Replaces part numbers: WPW10352973, W10352973, W10065190, W10163975, W10283468, 8183186, AP6020256, PS11753574. Controls dispenser drawer movement for proper release timing Easy to install with basic tools Fixes the following symptoms: Dispenser drawer not opening Detergent or softener not dispensing Error codes related to actuator failure Inconsistent or incomplete wash cycles Compatible with:Many models from Whirlpool, Maytag, Kenmore, Amana, and more.(Check model number before ordering or contact us for fitment help.) ✅ Why Buy from Parts-O-Matic? Guaranteed OEM-quality parts Always Fast and Free U.S. shipping Competitive pricing Expert support for part compatibility 🛒 Get your washer working like new – order the WPW10352973 Dispenser Actuator now at Parts-O-Matic.com, and enjoy fast, free shipping with no minimum.

Read more less

XPARTCO DC97-16782A Dryer Drum Roller The XPARTCO DC97-16782A is an aftermarket replacement drum support roller compatible with select Samsung and Kenmore dryers. The drum roller is a rear support wheel that cradles the dryer drum and allows it to rotate smoothly during every drying cycle. Over time, the rollers wear down, causing the drum to wobble, squeak, or thump during operation — replacing them restores quiet, stable drum rotation. This roller features a self-lubricating bushing and includes the roller shaft and mounting tri-ring clips for a complete, ready-to-install assembly. It measures approximately 3-1/4 inches in diameter and directly replaces OEM part numbers DC97-16782A, DC97-07523A, and DC97-07523B. Sold individually — most Samsung dryers use two rear drum rollers, so we recommend replacing both at the same time. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO DC97-16782A Dryer Drum Roller fixes squeaking, thumping, or rumbling noises coming from Samsung and Kenmore dryers during operation. The drum roller supports the rear of the dryer drum — when worn, it causes noise and uneven drum rotation. Includes roller shaft and mounting clips. Approximately 3-1/4" diameter. Compatible with select Samsung and Kenmore dryers. Common Problems This Part Fixes Loud squeaking, thumping, or rumbling noise during dryer operation Drum wobbling or vibrating excessively during the drying cycle Grinding or scraping sound as the drum rotates Dryer making noise that gets worse over time Visible flat spots, cracks, or worn surfaces on existing drum rollers Drum not rotating smoothly or spinning unevenly Replaces Part Numbers This drum roller directly replaces the following OEM and cross-reference part numbers: DC97-16782A, DC97-16782C, DC97-16782D, 2027851, DC97-07523A, DC97-07523B, PD00002021, EAP4221885, AP5325135, PS4221885, WPW10177428, AP6016361, W10177428, 35001136, DC97-07523A, ASM930889, PD00003650, EAP11749648, AP6016361, PS11749648. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum roller is compatible with select dryers from the following brands: Samsung dryers (gas and electric — DV2, DV3, DV4, DV5, DVE, DVG series) Kenmore / Sears dryers (select models built on Samsung platform) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Supports the rear of the dryer drum for smooth, stable, quiet rotation during every cycle Approximately 3-1/4" diameter — direct replacement for OEM DC97-16782A, DC97-07523A, and DC97-07523B Self-lubricating bushing — no additional grease or oil required after installation Complete assembly includes roller shaft and mounting tri-ring clips — everything needed for installation Durable rubber and metal construction — resists wear, cracking, and heat damage Aftermarket replacement built to OEM-equivalent quality standards Often replaced together with the drum belt (6602-001655) and idler pulley (DC93-00634A) for a complete drum drive repair DIY-friendly repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number DC97-16782A Part Type Dryer Drum Support Roller Condition Aftermarket Replacement Application Gas and Electric Dryers Diameter Approximately 3-1/4 inches Dimensions 3" L x 2-1/2" W x 3" H Material Rubber / Plastic / Metal Lubrication Self-lubricating bushing (no grease needed) Includes Roller, shaft, and mounting tri-ring clips Sold As Single roller (most dryers require 2 — replace both) Compatible Brands Samsung, Kenmore Often Replaced With 6602-001655 Drum Belt, DC93-00634A Idler Pulley Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. To access the drum rollers, remove the top panel and front panel of the dryer, then release the drum belt tension at the idler pulley and lift the drum out of the cabinet. The two rear drum rollers are located on the rear bulkhead. Remove the mounting clip, slide the old roller off the shaft, and install the new DC97-16782A roller — the shaft thread is clockwise. Reinstall the mounting clip to secure the roller. Replace both rear rollers at the same time even if only one appears worn. Reassemble the dryer, restore power, and run a test cycle. Tip: While the drum is out, inspect and replace the drum belt (6602-001655) and idler pulley (DC93-00634A) if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions How many drum rollers does my Samsung dryer need? Most Samsung dryers have two rear drum support rollers. This listing is for a single roller. We strongly recommend replacing both rollers at the same time — even if only one appears damaged — since they wear at the same rate and replacing both prevents the need to disassemble the dryer again soon after. What does the drum roller do? The drum rollers are support wheels mounted on the rear bulkhead of the dryer. They cradle the back edge of the dryer drum and allow it to spin smoothly during operation. When the rollers wear down or develop flat spots, the drum wobbles and creates loud squeaking, thumping, or grinding noises. Does DC97-16782A replace DC97-07523A and DC97-07523B? Yes. The DC97-16782A is the updated part number that directly supersedes both DC97-07523A and DC97-07523B. If your dryer originally used either of those older part numbers, the DC97-16782A is the correct current replacement. Should I also replace the drum belt and idler pulley at the same time? Yes — since the dryer is already fully disassembled to replace the rollers, it is highly recommended to also inspect and replace the drum belt (6602-001655) and idler pulley (DC93-00634A) at the same time. These three parts wear together and are commonly sold as a dryer repair kit, saving you from having to take the dryer apart again in the near future. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is made from durable rubber, plastic, and metal to match the dimensions and performance of the original DC97-16782A roller. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

W10775188 Washer Genuine OEM Washplate Replaces Part Numbers: W10775188, 4282681, W10698538, W10834891, AP5959417, PS11699797. W10775188 Washer Washplate – Genuine OEM Part Restore optimal cleaning power with the W10775188 Washer Washplate. This Genuine OEM part replaces a worn or damaged washplate to ensure efficient agitation and even cleaning performance. Key Features: ✅ Genuine OEM Part – built to factory specs 🔁 Replaces: 4282681, W10698538, W10834891, AP5959417, PS11699797 🌀 Provides powerful agitation for deep cleaning 🛠️ Fits select Whirlpool, Maytag, and Amana top-load washers 🧰 Easy to install – includes center bolt ⚠️ Always unplug your washer before servicing. Need help with compatibility? Contact us! 📦 Part Number: W10775188

Read more less

XPARTCO WH11X34740 Washer Drain Pump Assembly – Compatible with GE & Hotpoint Washers Product Description Restore proper draining and reliable washer operation with the XPARTCO WH11X34740 Washer Drain Pump Assembly. This high-quality replacement pump is responsible for removing water from the washer during drain and spin cycles. A failing drain pump can cause standing water, slow draining, loud grinding noises, or error codes. Replacing it with this durable XPARTCO assembly helps ensure efficient water removal and dependable washing performance. XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers WH23X25518, WH23X10038, WH23X25461, PD00079543, EAP16743374, AP7195487, PS16743374. Compatibility This replacement washer drain pump assembly fits select GE and Hotpoint washers. Example compatible models include (but are not limited to): GE GTW465ASNWW, GTW335ASNWW Hotpoint HTW240ASKWS Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and pumping performance 💧 Efficient Water Removal – Restores proper draining during cycles 🔇 Quiet Operation – Helps eliminate grinding or buzzing noises 💪 Durable Motor Construction – Designed for long service life 💰 Cost-Effective Repair – Reliable alternative to OEM drain pumps 📐 Product Specification Part Number: WH11X34740 Component Type: Washer Drain Pump Assembly Voltage: 120V AC Mounting: Direct-fit, bolt-on installation Application: Washer drain and spin system Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver, pliers ⚠️ Safety First: Unplug the washer and shut off the water supply before servicing. Basic Steps: Disconnect washer power and water supply. Access the drain pump from the bottom or rear of the washer. Remove hoses and electrical connectors. Remove mounting screws and take out the old pump. Install the new XPARTCO WH11X34740 drain pump assembly. Reconnect hoses and wiring, reassemble panels, and restore power. Run a test cycle to confirm proper draining. ⏱️ Time Required: 25–35 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore proper washer draining and prevent water buildup — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

WPW10409079 Washer Genuine OEM Drain Pump Replaces Part Number: WPW10409079, W10409079, 2118648, AP6021043, PS11754363, LP09079. Description: This Drain Pump is a replacement part for specific Whirlpool top-loading washing machine models. Located near the bottom center of the machine, it actively pumps water out of the washer tub at the end of each cycle.  The pump motor spins an impeller chamber to push water through the drain hose and out of the home. Causes of failure include clogging from mineral buildup or fabric fibers within the pumping components. Over time, motor windings experience excess heat and may burn out from consistent drainage cycles. WPW10409079 is the part number for a Whirlpool washer drain pump that removes water from the washer during the drain cycle. It is compatible with many Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef models.

Read more less