WE04X25198 Dryer Genuine OEM Thermostat
Fits Specific GE Dryer Models.
Replaces Part Numbers: WE04X25198, 4467032, AP6024634, PS11736631.
Description: This Thermostat is a Genuine OEM component specifically designed for specific GE laundry machine models. It is a heat-sensing component that monitors and regulates air temperatures inside the dryer drum. Precise thermostat functioning ensures proper drying temperatures are reached and maintained for optimal performance.
WE04X20685 Genuine OEM GE Dryer Thermistor
The WE04X20685 is a genuine GE OEM center outlet thermistor for GE dryers, and also fits select Hotpoint, RCA, and Kenmore models. This thermistor monitors exhaust air temperature and communicates real-time readings to the control board, letting it track how the dryer is operating throughout the cycle.
Importantly, this thermistor is not part of the heating circuit itself, so it's unlikely to be the cause of a dryer that won't heat or produces too much or too little heat. Instead, when this thermistor malfunctions, it typically affects cycle timing or triggers a fault code, since the control board is receiving inaccurate or missing temperature data from this specific sensor location rather than losing its ability to regulate the heating element. A healthy thermistor reads approximately 100K ohms at room temperature. Common failure causes include moisture exposure gradually degrading the electronics over time, or physical stress damaging the thin connecting wires. Before assuming this thermistor is the cause of any symptom, it's worth confirming your exhaust venting has good airflow and is free of obstructions. It directly replaces WE4M336, 4369857, 76J1HX0005, AP5985030, AGE25863, EAP11721518, EAP11721518, OEM17955099, PD00043358, PS11721518.
Quick Answer
The WE04X20685 Genuine OEM GE Dryer Thermistor fixes GE, Hotpoint, RCA, and Kenmore dryers with incorrect cycle timing or a fault code related to this sensor. Reads approximately 100K ohms at room temperature. Replaces WE4M336, 4369857, 76J1HX0005, AP5985030, AGE25863, EAP11721518, EAP11721518, OEM17955099, PD00043358, PS11721518. This thermistor is not part of the heating circuit — it's unlikely to be the cause of a no-heat or overheating problem, but can affect cycle timing or trigger a fault code if defective.
Common Problems This Part Fixes
Incorrect or inconsistent cycle timing
Fault code related to this thermistor or temperature sensing
Erratic cycle behavior not explained by a heating element or thermal fuse issue
Control board receiving inaccurate temperature data from this sensor location
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer thermistor directly replaces the following OEM and cross-reference part numbers:
WE04X20685, WE4M336, 4369857, 76J1HX0005, AP5985030, AGE25863, EAP11721518, EAP11721518, OEM17955099, PD00043358, PS11721518
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This thermistor is compatible with select GE dryers, and also fits select Hotpoint, RCA, and Kenmore dryers built on the GE platform.
Note: This is a center outlet thermistor and is not in the heating circuit — a different function from some other GE thermistors that do regulate heat output directly. Always verify your full model number before ordering, since GE uses different thermistor designs and resistance ratings across its dryer lineup. Contact our support team with your model number if you're unsure.
Key Features
Genuine GE OEM part — factory-specified resistance curve and mounting fit
Center outlet thermistor monitors exhaust air temperature and reports it to the control board
Not part of the heating circuit — affects cycle timing and fault codes rather than heat output
Reads approximately 100K ohms at room temperature
Direct drop-in replacement matching the original mounting and wiring
Replaces WE4M336, 4369857, 76J1HX0005, AP5985030, AGE25863, EAP11721518, EAP11721518, OEM17955099, PD00043358, PS11721518
Compatible with GE, Hotpoint, RCA, and Kenmore dryers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
WE04X20685
Part Type
Dryer Center Outlet Thermistor
Condition
Genuine OEM
Brand
GE
In Heating Circuit
No
Typical Resistance
Approx. 100K ohms at room temperature
Function
Monitors exhaust air temperature and reports to the control board
Repair Difficulty
Easy
Quantity
1 thermistor
Compatible Brands
GE, Hotpoint, RCA, Kenmore
Installation Notes
⚠️ Unplug Dryer Before Starting — Check Venting Before Assuming This Sensor Is At Fault Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Before replacing this thermistor, confirm that airflow at the home's outside vent hood is good and that the dryer's venting is free of obstructions, since this thermistor is not part of the heating circuit and won't cause a heating problem on its own. Remove the back panel of the dryer, typically secured with several screws, to access the thermistor's mounting location. Test the old thermistor with a multimeter for electrical continuity to confirm it's actually faulty before replacing it. Photograph the wiring before disconnecting anything. Disconnect the wire terminals from the old thermistor and remove it from its mounting position. Install the new WE04X20685 in the same position, reconnect the wire terminals, and reattach the back panel. Restore power and run a test cycle to confirm normal cycle timing with no fault codes. Tools needed: Phillips or nut driver (model-dependent), multimeter, work gloves.
Frequently Asked Questions
My dryer isn't heating. Is this thermistor the cause?
Unlikely. This is a center outlet thermistor and is specifically not part of the dryer's heating circuit, so a fault here is unlikely to explain a no-heat or overheating symptom. If your dryer isn't heating, check the thermal fuse, heating element, or high-limit thermostat first. This thermistor is more likely to be the cause if you're seeing incorrect cycle timing or a specific fault code instead.
What symptoms does this thermistor actually cause when it fails?
Since this sensor feeds temperature data to the control board without being in the heating circuit itself, a failure here typically shows up as incorrect cycle timing or a fault code related to this specific sensor, rather than affecting how hot or cold the dryer runs.
Should I check anything else before replacing this part?
Yes — confirm your dryer's exhaust venting has good airflow and no obstructions before assuming this thermistor is at fault, since venting issues can cause a range of symptoms that might otherwise be mistaken for a sensor problem. This is a quick check worth doing first.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original resistance curve and mounting configuration of the thermistor originally installed in your dryer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 279838 Dryer Heating Element
The XPARTCO 279838 is an aftermarket replacement heating element for Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, Inglis, KitchenAid, and Jenn-Air electric dryers. This element is the source of virtually all the heat in the dryer: current flows through a nickel-chromium coil, which glows and radiates heat as the blower pushes air across it and into the drum. This part is often nicknamed the "shorty" because of its compact size compared to the larger, older Whirlpool element it replaced, part number 4391960 — the shorty design is used on dryers with the lint filter positioned on the top right near the control housing.
Over years of use, the coil typically fails with a visible break somewhere along its length — a section simply burns through and the circuit opens, cutting off heat entirely. A quick way to check: a healthy element reads approximately 9 to 10 ohms across its terminals with a multimeter; a reading of no resistance (open circuit) confirms the element has failed. This element shares the same dryer platform as our WP3392519 thermal fuse and works alongside a cycling thermostat and high-limit thermostat in the same heating circuit — all commonly checked or replaced together when a dryer stops heating. It directly replaces 279837, WP279837, 2438, 279838VP, 279838A, 3398063, 3398064, 3403585, 8565582, W10724237, AP3094254, AH334313, EA334313, PS334313, and PS3343130.
Quick Answer
The XPARTCO 279838 Dryer Heating Element fixes Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, Inglis, KitchenAid, and Jenn-Air electric dryers with no heat, insufficient heat, or drying times that have gotten noticeably longer. Also called the "shorty" element. Replaces 279837, WP279837, 2438, 279838VP, 279838A, 3398063, 3398064, 3403585, 8565582, W10724237, AP3094254, AH334313, EA334313, PS334313, PS3343130. A healthy element reads approximately 9-10 ohms with a multimeter; if the dryer has no heat at all, also check the thermal fuse (such as our WP3392519 listing) before assuming the element is at fault — a blown fuse produces the identical symptom.
Common Problems This Part Fixes
Dryer runs a full cycle but produces no heat at all
Dryer produces some heat, but not enough to dry clothes properly
Drying times that have gotten noticeably longer than they used to
Clothes coming out cold or barely warm at the end of a cycle
Visible break or burned-through section in the heating coil
Element that reads no resistance (open circuit) on a multimeter continuity or ohms test
Dryer that heats inconsistently, cycling on and off unexpectedly
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer heating element directly replaces the following OEM and cross-reference part numbers:
279838, WP279837, 279837, 2438, 279838A, 279838VP, 3398063, 3398064, 3403585, 8565582, W10724237, AH334313, AP3094254, AWP39215, PD00002351, EA334313, OEM9282771, PS334313.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This heating element is compatible with select Whirlpool electric dryers, and also fits select Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, Inglis, KitchenAid, and Jenn-Air dryers built on the same platform, including model numbers such as:
LER5624DQ0, LER4634EQ2
NED4655EW, NED4600YQ1
WED4815EW, WED4800BQ1, WED49STBW1, WED8300SW0
MEDC465HW, MEDC215EW, MEDX655DW, MEDX655DW1
RED4640YQ1, AED4675YQ1, AED4475TQ1
EED4400WQ0
Kenmore 70, 80, 90, 300, 400, 500, and 600 Series Model 110
Note: This element fits Whirlpool-platform dryers with the lint filter positioned on the top right near the control housing. It is a compact "shorty" design and is not the same element as the larger, older 4391960 used on earlier Whirlpool dryers. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement heating element — generates the heat that dries clothes
Resolves "no heat," "insufficient heat," and "drying takes too long" symptoms caused by a burned-through coil
Nickel-chromium coil for effective, heat-and-abrasion-resistant heating
Compact "shorty" design for dryers with the lint filter near the control housing
Direct drop-in replacement — no modification required
Replaces 279837, WP279837, 2438, 279838VP, 279838A, 3398063, 3398064, 3403585, 8565582, W10724237, AP3094254, AH334313, EA334313, PS334313, and PS3343130
Compatible with Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, Inglis, KitchenAid, and Jenn-Air electric dryers
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
XP279838
OEM Part Number
279838
Part Type
Dryer Heating Element Assembly ("Shorty")
Condition
Aftermarket Replacement
Coil Material
Nickel-chromium
Typical Resistance (Healthy Element)
Approx. 9-10 ohms
Legacy Predecessor
4391960 (larger, older design, not interchangeable)
Related Components
Cycling thermostat, high-limit thermostat, thermal fuse (see our WP3392519 listing)
Repair Difficulty
Medium — basic electrical skills and dryer panel disassembly required
Quantity
1 heating element assembly
Compatible Brands
Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, Inglis, KitchenAid, Jenn-Air
Installation Notes
⚠️ Unplug Dryer Before Starting — Test Resistance Before Assuming It's The Element Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel or the front, depending on your model, to reach the heater duct/blower housing area where the element is mounted. Before removing anything, inspect the old element visually for a break in the coil — sometimes you can see it directly, or feel it by gently wiggling each section of the coil. If nothing is visibly broken, test with a multimeter: place one probe on each terminal and look for a reading of approximately 9-10 ohms on a good element; no resistance at all confirms the element has failed. Photograph the wiring before disconnecting anything. Disconnect the wire terminals from the old element, remove the mounting screws or clips holding it in the duct housing, and pull it free. Install the new 279838 assembly in the same position, reconnect the wire terminals, and secure the mounting hardware — if the original connection wire shows burning or damage, replace it as well rather than reusing a damaged connector. Reassemble the panel, restore power, and run a test cycle to confirm the dryer is heating normally. Tools needed: 1/4" nut driver, 5/16" wrench, Phillips screwdriver, multimeter, work gloves.
Frequently Asked Questions
How do I test whether the element is actually bad?
Start with a visual inspection — often you can see a break directly in the coil, or find it by gently wiggling each section to check for a loose or separated point. If nothing is visible, use a multimeter set to ohms and place one probe on each terminal. A good element typically reads approximately 9 to 10 ohms; a reading of no resistance at all (open circuit) confirms the element has failed and needs replacing.
My dryer has no heat at all. Should I replace the element first, or check something else?
Check the thermal fuse first, since a blown fuse produces the exact same "no heat at all" symptom as a failed heating element and is a cheaper, faster part to test and replace — our WP3392519 listing covers the thermal fuse used on this same dryer platform. If the fuse tests good and the dryer still has no heat, the element itself is the next thing to test.
What's the difference between this "shorty" element and the older 4391960?
Both are Whirlpool dryer heating elements, but this 279838 is a more compact design used on dryers with the lint filter positioned on the top right near the control housing, while 4391960 is the larger, older element used on earlier Whirlpool dryer platforms. They are not interchangeable, so confirm which style your dryer uses — checking your model number or comparing the physical size of your old element — before ordering.
Should I check the connection wire while I'm replacing the element?
Yes, it's worth a look. The wire connecting to the element terminals can occasionally show burning or damage if the element was arcing or overheating before it failed. If you notice any discoloration, melting, or damage on the connection wire, replace it along with the element rather than reusing a compromised connector.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the nickel-chromium coil composition, resistance rating, compact "shorty" form factor, and terminal configuration of the original 279838 heating element used in compatible Whirlpool, Kenmore, Maytag, Amana, Roper, and related dryers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 3977393 Dryer Thermal Cut Off (309°F) – Compatible with Whirlpool, Maytag & Kenmore Dryers
Product Description
Protect your dryer from overheating with the XPARTCO 3977393 Dryer Thermal Cut Off (309°F). This high-quality aftermarket replacement is a critical safety component designed to permanently interrupt power to the heating circuit if temperatures exceed 309°F (154°C).
A blown thermal cut off can result in no heat. Replacing it with this reliable XPARTCO component helps restore safe operation and prevent further damage to heating elements or internal components.
XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and performance.
Replaces Part Numbers
3977393, AP3094244, PS334299, EAP334299
Compatibility
This replacement dryer thermal cut off fits select Whirlpool, Maytag, Kenmore (Whirlpool-manufactured), Amana, Estate, and Roper dryers.
Commonly installed on the heater housing assembly.
Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Matches OEM temperature rating and fit
🌡️ 309°F (154°C) Cut-Off Rating – Designed for high-heat safety protection
🛡️ Prevents Overheating Damage – Protects heating element and dryer components
🧩 Direct-Fit Design – Installs easily without modification
💰 Cost-Effective Repair – Affordable alternative to OEM thermal cut offs
📐 Product Specification
Part Number: 3977393
Component Type: Dryer Thermal Cut Off
Temperature Rating: 309°F (154°C)
Function: One-time over-temperature safety cutoff
Mounting: Screw-mounted
Application: Dryer heater housing assembly
Quality Level: Aftermarket replacement (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, nut driver
⚠️ Safety First: Unplug the dryer before servicing to avoid electrical shock.
Basic Steps:
Disconnect dryer power.
Remove rear panel to access heater housing.
Locate and disconnect the old thermal cut off.
Remove mounting screws and install the new XPARTCO 3977393 cut off.
Reconnect wiring and reassemble the dryer.
Restore power and test operation.
⏱️ Time Required: 20–30 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Aftermarket Appliance Parts
🔄 30-Day Return Policy
Restore dryer safety and prevent overheating — Add to Cart Now for a dependable, budget-friendly repair!
ERP 3406108 Dryer Door Switch
Replaces Part Numbers: WP3406108, 3406108, PS11741702, AP6008562
Description: This Door Switch is a replacement part for select Whirlpool dryer models. It is responsible for detecting whether the dryer door is open or closed. When the door is closed, the switch allows the dryer to operate. Conversely, if the door is open, the switch interrupts the electrical circuit to prevent the dryer from running, ensuring safety during use.
Fits Models: LTE5243DQ1 , LTE5243DQ2 , LTE5243DQ3 , LTE5243DQ4 , LTE5243DQ5 , LTE5243DQ6 , LTE5243DQ7 , LTE5243DQ8 , LTE5243DQ9 , LTE5243DQA , LTE5243DQB , LTE5243DT2 , LTE5243DT3 , LTE5243DT4 , LTE5243DT5 , LTE5243DT6 , LTE5243DT7 , LTE5243DZ1 , LTE5243DZ2 , LTG5243DQ1 , LTG5243DQ2 , LTG5243DQ3 , LTG5243DQ4 , LTG5243DQ5 , LTG5243DQ6 , LTG5243DQ7 , LTG5243DQ8 , LTG5243DQ9 , LTG5243DQA , LTG5243DQB , LTG5243DQC , LTG5243DT2 , LTG5243DT3 , LTG5243DT4 , LTG5243DT5 , LTG5243DT6 , LTG5243DT7 , LTG5243DT8 , LTG5243DZ1 , LTG5243DZ2 , WET4024EW0 , YLTE5243DQ2 , YLTE5243DQ3 , YLTE5243DQ4 , YLTE5243DQ5 , YLTE5243DQ6 , YLTE5243DQ7 , YLTE5243DQ8 , YLTE5243DQ9 , YLTE5243DQA , YLTE5243DQB , YWET4024EW0.
This is an aftermarket part that can be used as a replacement for the OEM part.
ERP DC47-00015A Dryer Thermostat
Fits Specific Samsung, Whirlpool Dryer models.
non-resettable dryer thermostat.
Description: This Dryer Thermal Fuse is a exact replacement Part that is situated on the heating element housing for specific Samsung, Whirlpool dryer models. It meticulously measures the air temperature within the dryer drum and adjusts the heat to maintain the optimal drying temperature. In situations where your dryer doesn't start, fails to dry clothes effectively, or doesn't produce heat, a faulty thermal fuse might be the cause.
Replaces Part Numbers:DC47-00015A, 2068544, 35001091, 1122484, AH2038382, DC47-00015A, EA2038382, AP4201892, PS4205212, AP4045835, PS2038382.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: California’s Proposition 65
XPARTCO 3406105 Dryer Door Switch Replaces WP3406105
The XPARTCO 3406105 is an aftermarket replacement dryer door switch assembly compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef, and Norge. The door switch is a safety component mounted inside the dryer cabinet near the door opening. When the door is closed, the door strike depresses the switch actuator, completing the circuit and allowing the dryer to start and run. When the door is opened, the switch opens the circuit and stops the dryer. On models with a broken belt detection circuit, the door switch also plays a role in belt failure detection. A failed door switch causes the dryer to either not start at all or to run continuously with the door open.
This is a Single Pole, Double Throw (SPDT) 3-wire switch with stainless steel terminals and a heat-resistant housing. It measures 1-3/4" L x 1-5/8" W x 1-1/4" H with a 7-3/4" wiring harness. Electrical specs are 120-240V, 50-60Hz, 11A, 1/3HP. The kit includes the switch and 3-wire harness assembly. It directly replaces WP3406105, 3406104, 3405104, 3405105, 528947, AP6008560, and several additional cross-reference numbers. Installs in 15–30 minutes with basic hand tools.
Quick Answer
The XPARTCO 3406105 Dryer Door Switch fixes Whirlpool-family dryers that won't start, won't stop when the door is opened, or require the door to be slammed to start. SPDT 3-wire switch, 120-240V/50-60Hz/11A/1/3HP. Body 1-3/4" L x 1-5/8" W x 1-1/4" H, 7-3/4" harness. Includes switch and harness assembly. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, and more. Replaces WP3406105, 3406104, 3405104, 528947, AP6008560.
Common Problems This Part Fixes
Dryer will not start at all — door switch not completing the circuit when door is closed
Dryer starts only when the door is slammed or held firmly closed
Dryer continues to run after the door is opened — switch not opening the circuit
Drum light not turning on when the door is opened (on models with drum light)
Dryer starts intermittently — door switch contact worn and making unreliable contact
Dryer stops mid-cycle randomly — switch opening the circuit due to vibration or wear
Door switch visibly cracked, broken, or the actuator button no longer springs back
Replaces Part Numbers
This door switch directly replaces the following OEM and cross-reference part numbers:
WP3406105, 3405104, 3405105, 3406104, 3406105, WP3406105VP, AWP47182, PD00003898, EAP11741700, AP6008560, PS11741700.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This door switch is compatible with select gas and electric dryers from the following brands:
Whirlpool dryers (gas and electric)
Kenmore / Sears dryers (Whirlpool-built models)
Maytag dryers (gas and electric)
KitchenAid dryers
Amana dryers
Roper dryers
Estate dryers
Crosley dryers
Inglis dryers
Admiral dryers
Jenn-Air dryers
Magic Chef dryers
Norge dryers
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Safety switch — prevents dryer from operating when the door is open and stops the dryer immediately when the door is opened mid-cycle
Single Pole, Double Throw (SPDT) 3-wire switch — provides both normally-open and normally-closed contacts for dryer start circuit and belt failure detection on compatible models
Rated 120-240V, 50-60Hz, 11A, 1/3HP — correct electrical specifications for compatible Whirlpool-family dryers
Switch body: 1-3/4" L x 1-5/8" W x 1-1/4" H; wiring harness: 7-3/4" L
Stainless steel terminals and heat-resistant housing
Kit includes switch and 3-wire harness assembly — complete plug-in replacement
Replaces WP3406105, 3406104, 3405104, 3405105, 528947, and AP6008560
Compatible with 13 major appliance brands on the Whirlpool platform
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY repair — installs in 15–30 minutes with basic hand tools
Product Specifications
Part Number
3406105
OEM Part Number
WP3406105
Part Type
Dryer Door Switch Assembly (SPDT 3-Wire)
Condition
Aftermarket Replacement
Application
Gas and Electric Dryers
Switch Type
Single Pole, Double Throw (SPDT)
Wires
3-wire
Voltage
120-240V
Frequency
50-60Hz
Amperage
11A
Horsepower
1/3 HP
Switch Body Dimensions
1-3/4" L x 1-5/8" W x 1-1/4" H
Harness Length
7-3/4 inches
Color
Off-White / Black / Gray
Material
Plastic / Metal (stainless steel terminals)
Includes
Switch and 3-wire harness assembly
Compatible Brands
Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef, Norge
Installation Notes
⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. The door switch is located inside the dryer cabinet near the door opening, typically mounted in the front panel or top panel. Access it by inserting a putty knife under the top panel to release the spring clips and lift the top, then release the front panel. Locate the old door switch — it is a small rectangular component with a spring-loaded actuator button. Photograph the wiring connections before disconnecting. Disconnect the 3-wire harness from the old switch. Release the switch from its mounting bracket by pressing the retaining tabs and pulling the switch free, or unscrewing the mounting screw. Snap the new 3406105 switch into the mounting bracket and reconnect the 3-wire harness in the same positions. Reassemble the front and top panels, restore power, and run a test cycle to confirm the dryer starts, stops when the door is opened, and runs normally. Tools needed: Phillips screwdriver, putty knife.
Frequently Asked Questions
What does the dryer door switch do?
The door switch is a safety component that monitors whether the dryer door is open or closed. When the door is closed, the door strike depresses the switch actuator, completing the electrical circuit and signaling the control board that it is safe to run. When the door is opened, the actuator releases, opening the circuit and stopping the dryer immediately. On many Whirlpool-family dryers, the 3-wire SPDT switch also provides a secondary circuit used for broken belt detection — one of the switch's contacts is part of the motor start circuit, while the other is part of a safety cutoff circuit.
How do I test the door switch with a multimeter?
Unplug the dryer and disconnect the switch from the harness. Set your multimeter to continuity mode. The 3406105 is an SPDT switch with three terminals — typically labeled Common (C), Normally Open (NO), and Normally Closed (NC). With the actuator button not pressed (door open position), you should read continuity between C and NC, and no continuity between C and NO. With the actuator button pressed (door closed position), you should read continuity between C and NO, and no continuity between C and NC. Any deviation from this pattern confirms the switch has failed.
What is the difference between 3406105 and 3406104?
The 3406104 was the original part number, and the 3406105 (later updated to WP3406105) is the current replacement that superseded it. They are the same door switch and are fully interchangeable. The 3405104 and 3405105 are also cross-references for this same switch from earlier production. If your dryer's documentation or old switch label shows any of these numbers, the 3406105 is the correct current replacement.
Why does this switch have 3 wires when my old switch only had 2?
The WP3406105 is an SPDT (Single Pole, Double Throw) switch with 3 terminals — Common, Normally Open, and Normally Closed. Some older dryer models used a simpler 2-wire switch, but the 3-wire WP3406105 is the updated replacement that works on both older and newer models. On models that originally had a 2-wire switch, only two of the three terminals are used — the third is simply left unconnected. Follow your model's wiring diagram or take a photo of the original switch's wire connections before removing it.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from durable plastic and metal with stainless steel terminals to match the dimensions and electrical specifications of the original WP3406105 door switch assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
WE4M488 Dryer Control Board
Replaces Part Numbers: WE4M488, 2218486, WE4M331, WE4M388, AH3487192, EA3487192, AP4980176, PS3487192.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
WE4X800 Dryer Genuine OEM Thermostat
Replaces Part Numbers: WE4X800, 2285, AH268245, EA268245, ET800, WE04X0730, WE04X0800, WE4X730, OEM10477750, AP2619437, PS268245.
Description: This Thermal Cut-Off Kit is a Genuine OEM part for specific GE dryer models. This safety kit is designed to protect the dryer from overheating by interrupting the heat source when the dryer air temperature reaches dangerously high levels.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO WE03X29897 Dryer Drum Belt
The XPARTCO WE03X29897 is an aftermarket replacement drum drive belt for GE, Hotpoint, and Kenmore dryers. It is a four-rib belt, approximately 89-1/2 inches long, that wraps around the drum, the tension pulley, and the drive motor pulley, so the motor can turn the drum. A worn, stretched, or broken belt can cause noise, a drum that won't turn, or a dryer that won't start.
This is a direct-fit aftermarket replacement for the original GE belt. Because the drum has to be moved to fit a new belt, it is also a good time to inspect the tension pulley, idler, and drum rollers and replace any that look worn.
Quick Answer
The XPARTCO WE03X29897 Drum Belt fixes a GE, Hotpoint, or Kenmore dryer whose drum won't turn, that makes a noisy thumping or squealing sound, or that won't start because the belt is worn or broken. Classic symptom: the dryer hums or the motor runs, but the drum stays still.
Common Problems This Part Fixes
Drum does not turn although the motor runs
Noisy dryer, with thumping or squealing as the drum turns
Dryer won't start
Heat stays on after the drum has stopped
Visibly stretched, cracked, or broken belt
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This drum belt directly replaces the following part numbers:
WE03X29897, WE12M29, WE12X21574, WE21M29, 559C197P001, 559C197P003, 254C1413P002, 3516321, 4 PH 2275, SH210T, 4975431, WE12M0022, WE12M22, WE12M33, 559C197P004, 559C197P005, 559C197P006, WE120122, AGE25601, AP7012633, EAP10065160, PD00074201, PS16542496
These numbers span several generations of GE's own part numbering for this belt. Confirm against your dryer's parts diagram, or contact our support team, if your model calls out a different number.
Compatibility
This drum belt is listed for GE, Hotpoint, and Kenmore dryers and washer-dryer combos, including these examples:
GE DBB3300EA0AA, DBLR333EE0CC, DNCK440GG9WC, DWXR473GT5WW
GE DDC4400T3WH, DRSR495EG0WW, DX2300EB1WW, DX4500EG1WW
GE 2661532210 and 3636154241, Kenmore 36371542
Note: The models above are a small sample of a list of hundreds, not a full list. Compare your old belt's length to this one (approximately 89-1/2 inches), and contact our support team to verify fit before ordering.
Key Features
Direct-fit aftermarket drum drive belt for GE, Hotpoint, and Kenmore dryers
Four-rib design, approximately 89-1/2 inches long
Wraps around the drum, tension pulley, and motor pulley
Resolves drum-not-turning, noise, and no-start problems caused by a worn belt
Straightforward repair, typically 30 minutes to 1 hour
Product Specifications
Part Number
XPWE03X29897
OEM Part Number
WE03X29897
Part Type
Dryer Drum Drive Belt
Condition
Aftermarket Replacement
Belt Length
Approx. 89-1/2 Inches
Belt Profile
4-Rib
Application
GE, Hotpoint & Kenmore Dryers
Installation Notes
⚠️ Unplug Power Before Installing Unplug the dryer before beginning, and shut off the gas supply first on gas models. Wear work gloves, as internal parts and cabinet edges can be sharp. Remove the top and front panel as shown in your model's service guide, then slide the drum out, which is easier with a second person. Remove the old belt and route the new belt around the drum, the tension pulley, and the motor pulley as the old one ran, then reassemble in reverse order. Check the tension pulley and drum rollers while the drum is out and replace any that are worn.
Frequently Asked Questions
My dryer runs but the drum won't turn. Is this the part I need?
That is the classic sign of a broken drum belt. If the motor runs and you can turn the drum freely by hand, check the belt first.
How long is this belt?
It is approximately 89-1/2 inches long, with four ribs. Small differences are normal, but if your old belt is a very different length, check your model number before ordering.
Should I replace anything else while the drum is out?
Inspect the tension pulley and the drum rollers or glides. These wear along with the belt, and they are much easier to replace now than later.
Will this fit my dryer?
It is listed for hundreds of GE, Hotpoint, and Kenmore dryers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 8573713 Gas Dryer Thermal Cut-Off Fuse Replaces WP8573713
The XPARTCO 8573713 is an aftermarket replacement thermal cut-off fuse for Whirlpool, Maytag, Kenmore, Crosley, Amana, and Inglis gas dryers. This fuse is mounted on top of the burner funnel, directly under the drum, and it's a one-time safety device: as long as the dryer stays within its normal operating temperature, it does nothing at all, but the instant temperatures near the burner climb high enough — almost always from restricted airflow — the fuse permanently opens the circuit and cuts power. That's why a blown fuse produces such a specific symptom: the dryer won't heat, even though the drum may still tumble and the rest of the dryer seems to run normally.
Because this fuse sits on the burner funnel underneath the drum rather than on the more accessible blower housing, replacing it is a more involved repair than a typical thermal fuse swap — the drum has to come out of the cabinet to reach it. Unlike a resettable thermostat, this fuse cannot be reset once it blows; it must be replaced. A blown thermal fuse is almost always a symptom rather than a random failure: restricted exhaust venting is the leading cause, since trapped heat near the burner is exactly what this fuse is designed to react to. It directly replaces WP8573713, AP6013467, and PS11746693.
Quick Answer
The XPARTCO 8573713 Gas Dryer Thermal Cut-Off Fuse fixes Whirlpool, Maytag, Kenmore, Crosley, Amana, and Inglis gas dryers that won't heat, even if the drum still tumbles normally. Mounted on the burner funnel under the drum. Replaces WP8573713, AP6013467, PS11746693. Always inspect and clean the dryer venting when replacing this fuse — a blown fuse is a symptom of restricted airflow, and installing a new fuse without fixing the vent will likely blow it again.
Common Problems This Part Fixes
Dryer runs and tumbles but produces no heat
Dryer that stopped heating suddenly, especially after running unusually hot
Drying times that have gotten noticeably longer or clothes coming out damp
Repeated blown fuses on a dryer with a known venting or airflow restriction
Dryer that recently smelled like burning or overheating before losing heat
Continuity test shows an open circuit across the old fuse
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This gas dryer thermal cut-off fuse directly replaces the following OEM and cross-reference part numbers:
WP8573713, 1180872, 8573713, AP3866211, EAP990558, PS990558, AWP49233, PD00006618
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This thermal cut-off fuse is compatible with select Whirlpool gas dryers, and also fits select Maytag, Kenmore, Kenmore Elite, Crosley, Amana, Inglis, and Sears Canada gas dryers built on the Whirlpool platform, including model numbers such as WGD8500SR0, and Kenmore 11070372710 and 11071112020.
Note: This fuse is specific to gas dryers, mounted on the burner funnel. It is not the same fuse used on electric dryer platforms. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement thermal cut-off fuse — one-time safety device that cuts power if the dryer overheats
Mounted on top of the burner funnel, directly under the drum
Resolves "runs but won't heat," "drying takes too long," and "clothes coming out damp" symptoms caused by a blown fuse
Replaces WP8573713, AP6013467, and PS11746693
Compatible with Whirlpool, Maytag, Kenmore, Kenmore Elite, Crosley, Amana, Inglis, and Sears Canada gas dryers
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
8573713
OEM Part Number
WP8573713
Part Type
Gas Dryer Thermal Cut-Off Fuse
Condition
Aftermarket Replacement
Application
Gas Dryers
Location
Top of the burner funnel, under the drum
Resettable
No — one-time use, must be replaced once blown
Material
Plastic housing
Dimensions
Approx. 1"H x 1"W
Repair Difficulty
Moderate to Hard — drum removal required for access
Quantity
1 thermal cut-off fuse
Compatible Brands
Whirlpool, Maytag, Kenmore, Kenmore Elite, Crosley, Amana, Inglis, Sears Canada
Installation Notes
⚠️ Gas Safety — Shut Off The Gas Supply Before Starting This fuse sits directly on the burner funnel, close to the gas burner assembly. Before beginning, close the gas shutoff valve behind the dryer in addition to unplugging the dryer or shutting off its circuit breaker. If at any point you smell gas, stop immediately, leave the area, and do not operate any switches — contact your gas utility or a qualified technician. Do not attempt this repair if you are not comfortable working safely around a gas appliance's burner assembly; a qualified technician can complete it instead.
⚠️ Drum Removal Required — Inspect And Clean The Venting Before Reassembling Wear work gloves. This repair requires removing the drum from the dryer cabinet to access the burner funnel, so budget more time and disassembly than a typical thermal fuse swap. Remove the top and front panels according to your model's service diagram, disconnect the drive belt from the idler pulley, and lift the drum out of the cabinet to expose the burner funnel underneath. Photograph the wiring before disconnecting the old fuse's connectors. Test the old fuse for continuity with a multimeter to confirm it's actually blown (no continuity) rather than assuming, and test the new fuse to confirm it's good out of the box. This is the most important step: fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. A blown thermal fuse is a symptom of restricted airflow, and skipping this step means the new fuse is likely to blow again. Install the new 8573713 fuse on the burner funnel in the same mounting position, reconnect the wiring, and reassemble the drum, belt, and panels in reverse order. Restore the gas supply and power, and run a test cycle to confirm normal heating and shutoff behavior. Tools needed: Phillips or nut driver (model-dependent), multimeter, vent brush or vacuum attachment for cleaning ductwork, work gloves.
Frequently Asked Questions
My dryer tumbles fine but there's no heat. Is this the right part?
Yes, this is the classic symptom of a blown gas dryer thermal cut-off fuse. Because this fuse only interrupts the heating circuit and not the drive motor, the drum can continue tumbling completely normally while the dryer produces no heat at all. If you've confirmed the burner isn't igniting and the fuse tests as an open circuit, this is very likely the fix.
Why does this repair require removing the drum? My other dryer's fuse didn't need that.
This particular fuse is mounted on the burner funnel underneath the drum rather than on the blower housing at the back of the cabinet, which is where many thermal fuses on other platforms are located. Reaching the burner funnel requires taking the drum out of the cabinet, which is why this repair involves more disassembly than some other thermal fuse replacements.
I replaced the fuse and it blew again. What's going on?
This is a strong sign that the underlying cause — almost always restricted airflow — was never addressed. Thermal fuses don't fail from age; they blow because the dryer overheated. If a new fuse keeps blowing, thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications and mounting configuration of the original WP8573713 thermal cut-off fuse used in compatible Whirlpool, Maytag, Kenmore, Crosley, Amana, and Inglis gas dryers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO (2 Pack) EXP570 Dryer Door Latch Kit
The XPARTCO (2 Pack) EXP570 is a two-kit set of aftermarket replacement door catch and strike kits for dryers from Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis, LG, and other comparable brands. The catch and strike work as a pair: the strike on the dryer door engages the catch on the cabinet to hold the door shut for the whole cycle. When either part wears, cracks, or gets knocked out of alignment, the door stops latching reliably. It may not stay closed, it may pop open mid-cycle and let heat escape, or the dryer may refuse to start because it doesn't register the door as closed.
This 2-pack includes 2 kits, for a total of 2 door catches and 2 strikes. Each kit has 1 door catch and 1 strike, so you can replace the full latch set in one repair rather than guessing which half is worn, and keep a second kit for another dryer or a future repair. Because this latch design was used across several appliance families, the kit carries a long cross-reference list covering Whirlpool, Frigidaire, GE, LG, and Alliance-built part numbers; see the Replaces list below.
Quick Answer
The XPARTCO (2 Pack) EXP570 Dryer Door Latch Kit fixes a dryer door that won't stay closed, opens mid-cycle, or an open-door condition that keeps the dryer from starting, caused by a worn or damaged catch and strike. This 2-pack includes 2 kits (2 door catches and 2 strikes). Fits Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis, and LG dryers. Classic symptom: the door swings open on its own, or you have to hold it shut to get the dryer to run.
Common Problems This Part Fixes
Dryer door won't stay closed
Door pops open in the middle of a cycle
Dryer won't start because the open-door condition isn't clearing
Worn, cracked, or damaged catch or strike
Heat escaping around the door, leaving clothes damp
Door that no longer latches with a firm, positive click
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This door latch kit directly replaces the following part numbers:
5366021400, 5303207102, AP2153772, PS475419, AP2137890, PS455020, LA-1003, LA1003, PS2162263, AP4242465, WE1M1011, WE1X1192, WE1M536, WE1X1195, WE01X1158, WE01X10023, WE01X10188, WE01X10184, AP5324728, PS3502777, AP2042206, PS266893, AP5324728, PS3502777, AP2042209, PS266896, AP2042175, PS266861, AP2042031, PS264343, AP3775568, PS959860, AP5238145, PS959856, WE1X1194, PS266895, AP2042208, WE1M1011, WE1X1192, WE1M536, WE1X1195, WE01X1158, WE01X10023, WE01X10188, WE01X10184, AP5324728, PS3502777, AP2042206, PS266893, AP5324728, PS3502777, AP2042209, PS266896, AP2042175, PS266861, AP2042031, PS264343, AP3775568, PS959860, AP5238145, PS959856, 4027EL2001A, 4026EL3001A, PS3522845, AP5238145, AP5242421, PS3522822, 00491624, AP3735937, PS959856, 5366021400, 5303207102, AP2153772, PS475419, AP2137890, PS455020, 279570
This latch kit was sold under the part numbers of several manufacturers: Whirlpool and Maytag (279570), Frigidaire and Electrolux (5303207102), GE (WE01X10023 and related), LG (4027EL2001A, 4026EL3001A), and Alliance-built dryers (LA-1003). The AP/PS-prefixed numbers are third-party catalog cross-references for the same physical parts.
Compatibility
This latch kit is used on dryer models from the following brands:
Whirlpool, Kenmore (Whirlpool-built), Maytag, Amana, Roper, Estate, and Inglis dryers
Frigidaire, Electrolux, and Kenmore (Frigidaire-built) dryers
GE and Hotpoint dryers
Select LG and Kenmore (LG-built) dryers
Select Crosley, Norge, and Speed Queen dryers
Note: This kit fits specific models within each brand, not every dryer a brand has made, and the latch design differs between manufacturers. Match the number on your old catch and strike, or on your dryer's parts diagram, against the Replaces list above rather than relying on brand alone. Contact our support team with your model number and we'll verify fit before you order. If only the catch needs replacing, see our single EXP571 Dryer Door Catch.
Key Features
2-pack of aftermarket replacement dryer door latch kits, each with 1 door catch and 1 strike
Replaces both halves of the latch in one repair
Restores a secure door closure so heat stays in and the dryer runs efficiently
Resolves doors that won't stay shut, open mid-cycle, or trigger an open-door no-start
Cross-references to Whirlpool, Frigidaire, GE, LG, and Alliance OEM numbering
2 kits per order (2 door catches and 2 strikes in total)
Product Specifications
Part Number
EXP570 (2 Pack)
OEM Part Number
279570, 5303207102, WE01X10023, 4027EL2001A
Part Type
Dryer Door Latch Kit (Door Catch & Strike)
Condition
Aftermarket Replacement
Kit Contents
1 Door Catch & 1 Strike per Kit
Quantity
2 Kits (2 Door Catches & 2 Strikes)
Application
Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Frigidaire, GE, Hotpoint, Inglis & LG Dryers
Installation Notes
⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Open the door and inspect the old catch on the cabinet and the strike on the door for cracks, wear, or loose mounting. Remove the old catch and strike, keeping track of how each one is oriented and mounted. Fit the new catch and strike in the same positions and fasten them securely. Close the door and confirm it latches with a firm click, stays shut, and lines up evenly with the cabinet. If the door still won't seat properly after the swap, check the door hinges and alignment, since a misaligned door can wear out new latch parts quickly.
Frequently Asked Questions
My dryer door won't stay shut — is this the part I need?
Very likely. A worn or damaged catch or strike is a common reason a dryer door won't latch or pops open mid-cycle. Inspect both parts for cracks or wear. Because the two work as a pair, replacing both at once is the surest fix.
My dryer won't start and seems to think the door is open. Could this be the cause?
It can be. If the door isn't latching fully, the dryer may not register it as closed. If the latch looks fine and the door closes firmly but the dryer still won't start, the door switch may be the problem instead.
What's included in the kit?
This 2-pack includes 2 kits, and each kit has 1 door catch and 1 strike, so you get 2 catches and 2 strikes in total. If you only need the catch, we also offer it separately as the EXP571 Dryer Door Catch.
Will this fit my Whirlpool, Frigidaire, GE, or LG dryer?
This kit is cross-referenced to part numbers from all of those brands, but it fits specific models rather than every dryer. Match the number on your old latch parts or parts diagram against the Replaces list, or contact our support team with your model number and we'll confirm before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
