XPARTCO W10006355 Washer Shift Actuator
Fits specific Maytag, Kenmore, Whirlpool top-load machine models.
Replaces Part Numbers: WPW10006355, W10006355, AP6014711, PS11747977.
Description: This Shift Actuator is a replacement part for specific Maytag, Kenmore, Whirlpool washing machine models. It is an electronic component located inside the transmission that controls the shifting between wash cycles. The shift actuator receives signals from the washer control board to change modes, initiating proper movements to advance the cycle.
This is an aftermarket part that can be used as a replacement for the OEM part.
XPARTCO W10613606 Refrigerator Compressor Start Relay and Capacitor
The XPARTCO W10613606 is an aftermarket replacement compressor start relay and capacitor assembly compatible with a wide range of Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Jenn-Air, Admiral, Crosley, Dacor, Hardwick, Inglis, Litton, and Magic Chef refrigerators. The start relay is a small but critical electrical component that plugs directly onto the compressor terminals and provides the initial power surge needed to start the compressor motor. Once the compressor reaches operating speed, the relay drops out — leaving the compressor to run on its own. The capacitor (rated 15µF ±5%, 250VAC) works alongside the relay to store and release the burst of electrical energy needed on startup.
When the start relay fails, the compressor cannot start — causing the refrigerator to stop cooling entirely. A failed relay typically produces a clicking sound every few minutes as the compressor tries and fails to start, followed by a short rest, then another attempt. This kit includes both the start relay and the CBB61 capacitor. It directly replaces W10416065, 8208290, 8208368, C8931605, 67003186, 67005560, 67005561, 67005562, 67003764, 8171210, and several additional cross-reference numbers. Installs in under 15 minutes — no tools required in most cases.
Quick Answer
The XPARTCO W10613606 Refrigerator Compressor Start Relay and Capacitor fixes refrigerators that are not cooling, are too warm, or are making a repeated clicking sound every few minutes as the compressor tries to start. Plugs directly onto the compressor terminals. Kit includes start relay and 15µF 250VAC CBB61 capacitor. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, and more. Replaces W10416065, 8208290, C8931605, 67005560, and more. No tools required — installs in under 15 minutes.
Common Problems This Part Fixes
Refrigerator not cooling — compressor not running
Freezer section too warm or not freezing
Both refrigerator and freezer compartments gradually warming up
Repeated clicking sound every 2–5 minutes from behind or underneath the refrigerator
Compressor hums briefly then shuts off without reaching operating temperature
Refrigerator runs but cannot maintain set temperature
Shaking the start relay reveals a rattling sound inside — confirms internal failure
Replaces Part Numbers
This start relay and capacitor kit directly replaces the following OEM and cross-reference part numbers:
W10613606, 67005560, 3023300, 67003186, 67003764, 67005561, 67005562, W10416065, 8171210, 8208290, 8208368, W10244032, 302TFBYY, SSP14R302TFR, AWP41206, C8931605, PD00004905, EAP8746522, AP5787784, PS8746522.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This start relay and capacitor is compatible with select refrigerators from the following brands:
Whirlpool refrigerators (side-by-side, French door, bottom-freezer)
Kenmore / Sears refrigerators (select Whirlpool-built models)
Maytag refrigerators
KitchenAid refrigerators
Amana refrigerators
Jenn-Air refrigerators
Admiral refrigerators
Crosley refrigerators
Dacor refrigerators
Hardwick refrigerators
Inglis refrigerators
Litton refrigerators
Magic Chef refrigerators
Important: Always verify your refrigerator's model number and compare the old relay's shape and terminal configuration to the new part before installing. Some models may require trimming the wire connector tabs for a proper fit. Contact our support team with your model number if you need confirmation before ordering.
Key Features
Provides the initial electrical surge needed to start the compressor motor — without it, the compressor cannot run and the refrigerator cannot cool
Kit includes both the start relay and the CBB61 run capacitor (15µF ±5%, 250VAC) — everything needed in one package
Plugs directly onto the compressor terminals — no wiring or soldering required in most cases
Quick rattle test — shake the old relay; if it rattles, the internal contacts have failed and it needs replacement
Replaces W10416065, 8208290, C8931605, and over a dozen additional cross-reference part numbers
Compatible with 13 major appliance brands on the Whirlpool platform
Aftermarket replacement built to OEM-equivalent quality standards
Fast DIY repair — installs in under 15 minutes, no tools required in most cases
Product Specifications
Part Number
W10613606
Part Type
Refrigerator Compressor Start Relay and Capacitor Kit
Condition
Aftermarket Replacement
Application
Refrigerator Compressor (side-by-side, French door, bottom-freezer)
Capacitor Type
CBB61 Run Capacitor
Capacitor Rating
15µF ±5%, 250VAC
Kit Includes
1x Start relay, 1x CBB61 capacitor
Installation
Plug-in — no tools required in most cases
Compatible Brands
Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Jenn-Air, Admiral, Crosley, Dacor, Hardwick, Inglis, Litton, Magic Chef
Installation Notes
⚠️ Unplug Refrigerator Before Starting Unplug the refrigerator from the power outlet before beginning. Move the refrigerator away from the wall to access the rear or lower back panel. Remove the rear access panel by unscrewing the retaining screws to expose the compressor. The compressor is a large black dome-shaped component — the start relay and capacitor assembly plugs onto the side terminals. Grip the old relay firmly and pull it straight off the compressor pins. Shake it — if it rattles, the internal contacts have failed and replacement is confirmed. Compare the old relay to the new W10613606 to confirm the terminal layout matches. Align the new relay with the compressor pins and press it firmly on. Reinstall the access panel, restore power, and listen for the compressor to start and run normally within a few minutes. Note: Some models may require trimming the wire connector tabs or reversing the connector orientation for a proper fit — do not force the connection. Tools needed: Phillips screwdriver (for panel access only).
Frequently Asked Questions
What does the compressor start relay do?
The start relay plugs onto the compressor terminals and provides the brief but powerful surge of electrical current needed to start the compressor motor from a standstill. Once the compressor reaches operating speed — usually within a second or two — the relay drops out and the compressor runs on its own. Without a working start relay, the compressor cannot start at all, and the refrigerator stops cooling. The capacitor works alongside the relay to store and deliver the extra energy needed on startup.
How do I know if my start relay has failed?
The most reliable quick test is the rattle test: unplug the refrigerator, pull the start relay off the compressor, and shake it near your ear. A working relay is silent. A failed relay will rattle — the internal contacts have broken free and are loose inside the casing. Another sign is a repeated clicking sound every 2–5 minutes from the back of the refrigerator, where the compressor attempts to start, fails, trips the overload protector, rests, and tries again. If the fridge is warm and you hear clicking, check the relay first.
What is the difference between the start relay and the capacitor?
The start relay is the switching device that connects and disconnects the start winding of the compressor motor during startup. The capacitor stores a charge and releases it during startup to give the motor the additional torque it needs to get moving under load. Together they work as a startup system for the compressor. This kit includes both — replacing both at the same time ensures the complete startup circuit is fresh and reliable.
My fridge is still not cooling after replacing the start relay — what else could it be?
If replacing the start relay does not restore cooling, other possible causes include a failed compressor (the compressor runs but no longer builds pressure), a refrigerant leak in the sealed system, a failed start capacitor (if not replaced along with the relay), a bad overload protector, or a faulty main control board. Listen carefully after installing the new relay — if the compressor now starts and runs but the fridge still doesn't cool after several hours, a sealed system issue or refrigerant problem is likely and will require a certified technician.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications and terminal configuration of the original W10613606 start relay and capacitor assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
W11497943 Dishwasher Genuine Drain Pump Motor
Replaces Part Numbers: W11497943, AP6994646, PS16221213, W11412663.
Description: This Drain Pump Motor is a Genuine OEM component for select Maytag, Kenmore, Whirlpool dishwasher models. This electric motor powers the drain pump to empty wash water from the tub at the end of cycles. Common causes of a bad pump motor include wear over extended use, moisture damage degrading electronics, or electrical faults from voltage fluctuations.
DA97-07603B Genuine OEM Samsung Refrigerator Ice Maker
The DA97-07603B is a genuine Samsung OEM ice maker assembly for Samsung and select Maytag refrigerators. This is the freezer ice maker, located inside the freezer compartment — it is not the in-door icemaker used on many other Samsung models. This is a plastic tray-style ice maker with a 9-cube flex tray design, an 8-pin connector, and includes a motor for ice ejection, a water valve to fill the mold, and a thermostat that senses temperature and signals when it's time to release the finished ice.
This complete assembly contains the entire ice maker and its housing. If the mold's coating is flaking, or internal components have stopped functioning, replacing the full assembly resolves both problems at once. Failure symptoms include the ice maker not producing ice, reduced ice production, or loud popping sounds coming from the ice maker during operation. It directly replaces DA61-03213B, DA97-07603B, DA97-05037D, DA97-07603A, 2688774, DA59-00294A, DA61-03213B, DA63-06415A, DA97-05037A, DA97-05037C, DA61-05227, AP5651755, ASM105616, PD00002034, PS5575313.
Quick Answer
The DA97-07603B Genuine OEM Samsung Refrigerator Ice Maker fixes Samsung and select Maytag refrigerators where the freezer ice maker has stopped producing ice, is making less ice than usual, or is making loud popping sounds during operation. 9-cube flex tray, 8-pin connector. Replaces DA61-03213B, DA97-07603B, DA97-05037D, DA97-07603A, 2688774, DA59-00294A, DA61-03213B, DA63-06415A, DA97-05037A, DA97-05037C, DA61-05227, AP5651755, ASM105616, PD00002034, PS5575313. This is the freezer ice maker — it does not fit an in-door icemaker, and it is not a substitute for the DA97-07603C icemaker used on other models.
Common Problems This Part Fixes
Ice maker has stopped producing ice entirely
Ice maker producing less ice than it used to
Loud popping sounds coming from the ice maker during operation
Ice mold coating visibly flaking or deteriorating
Ice maker cycling but not ejecting ice properly
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This refrigerator ice maker directly replaces the following OEM and cross-reference part numbers:
DA97-07603B, DA97-05037D, DA97-07603A, 2688774, DA59-00294A, DA61-03213B, DA63-06415A, DA97-05037A, DA97-05037C, DA61-05227, AP5651755, ASM105616, PD00002034, PS5575313
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This freezer ice maker is compatible with select Samsung refrigerators, and also fits select Maytag refrigerators built on the Samsung platform, spanning model series including RF220D, RF220N, RF221N, RF22A4, RF23HC, RF260BE, RF261BE, RF263TE, RF27T5, RF28HD, RF28HF, RF28R6, RF28T5, RF30HD, and RF323T, including specific model numbers such as RF220NCTABC/AAA-0001.
Note — freezer icemaker only, and not a substitute for DA97-07603C: This is a drop-in replacement for the freezer icemaker only. It will not fit an in-door icemaker used on many other Samsung models. It also replaces the earlier DA97-07603A version, but is not a suitable substitute for the DA97-07603C icemaker used on other models, despite the similar numbering. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which icemaker your refrigerator needs.
Key Features
Genuine Samsung OEM part — factory-specified mold design and cycling mechanism
9-cube flex tray design
Includes motor for ice ejection, water valve for mold fill, and thermostat for temperature sensing
Resolves "not making ice," "reduced ice production," and "loud popping sounds" symptoms
8-pin connector for a direct electrical fit
Complete assembly — includes the ice maker and its housing
Direct drop-in replacement for the freezer compartment icemaker
Replaces DA61-03213B, DA97-07603B, DA97-05037D, DA97-07603A, 2688774, DA59-00294A, DA61-03213B, DA63-06415A, DA97-05037A, DA97-05037C, DA61-05227, AP5651755, ASM105616, PD00002034, PS5575313
Compatible with Samsung and select Maytag refrigerators
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
DA97-07603B
Part Type
Refrigerator Freezer Ice Maker Assembly
Condition
Genuine OEM
Brand
Samsung
Tray Style
Plastic, 9-cube flex tray
Connector
8-pin
Location
Freezer compartment (not an in-door icemaker)
Included Components
Ejection motor, water valve, thermostat, housing
Repair Difficulty
Easy — approx. 15 to 30 minutes
Quantity
1 ice maker assembly
Compatible Brands
Samsung, Maytag
Installation Notes
⚠️ Unplug Refrigerator And Shut Off Water Supply Before Starting Unplug the refrigerator from the power outlet and turn off the water supply before beginning. Wear work gloves. On bottom-freezer drawer-style models, most of the time in this repair goes toward removing the trays from the freezer and pulling the freezer door/drawer out for access — budget extra time for this step. Remove the ice maker cover by lifting it away from the housing. Remove the ice bucket and any cover plates blocking access. Photograph the wiring connection before disconnecting anything. Unscrew the ice maker from its housing, disconnect the water line connection and the 8-pin electrical connector, and carefully lift the old assembly out of its compartment. Install the new DA97-07603B in the same position, reconnect the water line and electrical connector fully, and secure it to the housing with its screws. Reinstall the ice maker cover, cover plates, and ice bucket, then replace the freezer trays and close the freezer door/drawer. Restore the water supply and power, then allow several hours for the first cycle to complete and confirm ice is being produced normally. Tools needed: Phillips screwdriver, work gloves.
Frequently Asked Questions
My ice maker makes loud popping sounds. Is this the part I need?
Yes, this is a documented symptom of a failing ice maker assembly, alongside reduced or stopped ice production. If you're hearing unusual popping noises during the ice-making cycle, replacing the complete assembly addresses the underlying mechanical or electrical issue rather than trying to isolate and repair a specific internal component.
My refrigerator has an in-door ice maker. Will this part fit?
No. This DA97-07603B is specifically a drop-in replacement for the freezer compartment icemaker and will not fit an in-door icemaker used on many other Samsung refrigerator models. Check where your current ice maker is physically located — inside the freezer versus built into the refrigerator door — before ordering.
Is this the same as the DA97-07603C icemaker I've seen for other models?
No. While this part does replace the earlier DA97-07603A version, it is explicitly not a suitable substitute for the DA97-07603C icemaker used on other Samsung models, despite the similar numbering. Always confirm your full model number rather than assuming based on a close part number match.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Samsung to factory specifications — guaranteed fit, materials, and performance. It matches the original mold design, motor, water valve, and thermostat configuration of the freezer ice maker originally installed in your refrigerator.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
W11414076 Genuine OEM Whirlpool Dishwasher Circulation Pump Motor Assembly
The W11414076 is a Genuine OEM Whirlpool replacement circulation pump and motor assembly compatible with a wide range of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea dishwashers. The circulation pump is the heart of the wash system — it pressurizes and delivers water to the spray arms, driving the jets that blast food and residue off your dishes throughout the wash and rinse cycles. When the circulation pump fails, cleaning performance collapses: dishes come out dirty or unrinsed, water pressure at the spray arms drops, and the machine may make loud droning or grinding noises.
This is a complete circulation pump and motor assembly. Common causes of failure include worn motor bearings (which produce a continuous drone that gets louder over time), deteriorated impellers, and seal breakdowns. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W11414076 is the current production part that supersedes W11122133. It also replaces AP6980104, EAP12745416, PS12745416, 4958907, and OEM20940317. Note: this assembly does not include the drain pump — your existing drain pump transfers over to the new assembly during installation. Installs in 45–90 minutes with basic hand tools (the dishwasher must be pulled out and laid on its back to access the pump).
Quick Answer
The W11414076 Genuine OEM Whirlpool Dishwasher Circulation Pump Motor Assembly fixes Whirlpool, KitchenAid, Maytag, Jenn-Air, and Amana dishwashers where dishes come out dirty or unrinsed, water pressure at the spray arms is weak, water pools in the tub, or the motor makes a loud droning/grinding noise. Complete circulation pump + motor assembly. Genuine OEM. Current part superseding W11122133; also replaces AP6980104, EAP12745416, PS12745416, 4958907, OEM20940317. Before ordering: if the motor runs but water is weak, try cleaning the impeller filter screen first — see the FAQ.
Common Problems This Part Fixes
Dishes coming out dirty or unrinsed — circulation pump not delivering water to the spray arms
Weak water pressure at the spray arms — impeller worn or motor failing
Loud droning noise that gets louder over time — worn motor bearings
Grinding or unusual noise during operation
Water retention/pooling in the bottom of the tub
Leaks from the pump housing — seal breakdown
Motor humming but spray arms barely turning
Reduced cleaning performance overall
Motor not running at all — failed pump motor windings
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This circulation pump motor assembly directly replaces the following OEM and cross-reference part numbers:
W11414076, W11122133, AP6980104, EAP12745416, PS12745416, 4958907, OEM20940321, AWP45352, PD00070783
W11414076 is the current OEM production part superseding W11122133. Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This circulation pump motor assembly is compatible with select dishwashers from the following brands:
Whirlpool dishwashers — select models (verify with your parts diagram)
KitchenAid dishwashers — select models
Maytag dishwashers — select models
Jenn-Air dishwashers — select models
Amana dishwashers — select models
Magic Chef dishwashers — select models
Admiral dishwashers — select models
Norge dishwashers — select models
Roper dishwashers — select models
Kenmore / Sears dishwashers — select Whirlpool-built models
Ikea dishwashers — select Whirlpool-built models
This assembly may comprise several parts — refer to your specific parts diagram to verify included items. Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance
Circulation pump and motor assembly — pressurizes and delivers water to the spray arms for effective cleaning and rinsing
Resolves "dirty dishes," "weak water pressure," "loud droning motor," "grinding noise," and "water pooling" symptoms when caused by pump failure
Addresses the common failure modes: worn motor bearings, deteriorated impellers, and seal breakdowns
Current OEM production part — directly supersedes W11122133
Also replaces AP6980104, EAP12745416, PS12745416, 4958907, and OEM20940317
Motor separates from the pump case with 3 Torx screws — some customers replace only the motor if the pump case is fine
Drain pump is not included — your existing drain pump transfers to the new assembly
Compatible with Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea dishwashers
DIY repair — installs in 45–90 minutes with basic hand tools
Product Specifications
Part Number
W11414076
Supersedes
W11122133
Part Type
Dishwasher Circulation Pump & Motor Assembly
Condition
Genuine OEM
Application
Dishwashers (Whirlpool platform)
Function
Delivers water to the spray arms for washing and rinsing
Motor Attachment
Separates from pump case with 3 Torx screws
Drain Pump
Not included — transfer your existing drain pump
Location
Bottom of dishwasher (access by laying unit on its back)
Compatible Brands
Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, Ikea
Installation Notes
⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Wear Work Gloves — Major Access Required Disconnect power at the breaker and shut off the water supply before beginning. Wear work gloves to protect your hands. This is a more involved repair because the circulation pump is on the bottom of the dishwasher. Throw the circuit breaker, remove the lower access panel, and open the electrical box to completely disconnect the electrical from the dishwasher. Disconnect the water supply line and the drain line. Remove the anchor screws securing the dishwasher to the counter, then pull the dishwasher out of the cabinet. Have a large towel ready — rotate the dishwasher and lay it on its back to access the pump on the bottom. Photograph everything before disconnecting. Disconnect all connections to the main circulation pump: the drain pump, the electrical connections, the leak-detection plate and circuit, and the water lines. Undo all clamps to the circulation pump. Remove the old circulation pump assembly. Transfer your existing drain pump to the new W11414076 assembly — it is not included. (If you're only replacing a noisy motor and the pump case is good, the motor separates from the case with 3 Torx screws and can be swapped on its own.) Install the new assembly, reconnect the drain pump, electrical connections, leak-detection plate, water lines, and all clamps, matching your photos. Stand the dishwasher back up, slide it into the cabinet, reconnect water/drain/electrical, and secure the anchor screws. Run a short test cycle and check for leaks. Note: use your dishwasher's onboard diagnostic function to confirm the pump was the issue — light/error codes vary by model, so check the quick guide that came with your specific dishwasher rather than relying on codes listed online for other models. Tools needed: Phillips screwdriver, Torx driver (T-set), nut driver, pliers, large towel, work gloves.
Frequently Asked Questions
The motor runs but water barely reaches the spray arms — do I definitely need a new pump?
Maybe not — try this first, because it could save you the entire repair. On many KitchenAid/Whirlpool-platform dishwashers, there's a fine filter screen INSIDE the circulation pump on the impeller. This screen can clog with microplastics and fine food particles over time (sometimes after a surprisingly small number of wash cycles), which chokes off water flow even though the motor is running perfectly. The screen can look clean but still be blocked — a real-world test is to hold water in the mesh cup: if it holds water like a cup instead of draining freely, it's clogged. Cleaning it with a toothbrush restores full flow. To access it you do have to pull the pump (the same disassembly as replacing it, then 2 Torx screws to open the pump), so if you're already this far in, disassemble and inspect the screen BEFORE installing a new pump — you may find the old pump is perfectly good. Running a dishwasher-safe cleaning product through the machine first is also worth a try.
My dishwasher motor is loud and getting louder — is that the pump?
Yes, that's a classic sign of worn circulation pump motor bearings. The motor bearings wear out over time, and as they degrade they produce a continuous drone that steadily gets louder. Once the bearings have failed, the noise won't go away on its own and the motor should be replaced. On this assembly, the motor separates from the pump case with 3 Torx screws — some customers who only have a bearing/noise problem (and an otherwise good pump case) simply swap the motor and reuse the case. If you order the full assembly, you get both, and you can decide during the repair whether to swap just the motor or the whole thing.
Does this come with the drain pump?
No — the W11414076 is the circulation pump and motor assembly, and it does not include the drain pump. During installation, you'll transfer your existing drain pump from the old assembly to the new one (it detaches and reattaches). This is normal for this repair. If your drain pump is also failing (separate symptoms: won't drain, water left standing after the cycle), that's a different part you'd order separately. The circulation pump handles washing/spray pressure; the drain pump handles emptying the tub.
What's the difference between W11414076 and W11122133?
These are the same circulation pump assembly across production revisions. W11122133 was the earlier OEM part number, and W11414076 is the current production version that Whirlpool issued as its direct replacement. Both are physically and functionally interchangeable — if your dishwasher's parts diagram shows W11122133, the W11414076 is the correct current replacement, and this listing covers both. The cross-references AP6980104, PS12745416, and 4958907 are additional catalog identifiers for the same part.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same circulation pump and motor assembly installed in compatible Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, and Kenmore Whirlpool-built dishwashers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
LCD60+5X440 HVAC OVAL DUAL RUN CAPACITOR
Engineered by an ISO manufacturer with over twenty years' experience in OEM capacitor fabrication, Linebacker® capacitors are manufactured by the OEM factory and are 100% in-line production tested to the same rigorous standards.
Features/Benefits
10,000 AFC pressure sensitive short circuit interrupting capability
3-year warranty from the date of purchase
Continuous life tested, oil leak tested and dielectric tested for insulation effectiveness
Life tested to 85° C operating temperature for 10,000 cycles
Manufactured with thick polypropylene foil to handle increased operating temperatures
Meets EIA-456A accelerated life test at 70° C for 60,000 hours
PCB-free oil to prevent over-heating
UL File # E352486
US and Canada UL approved (C22.2NO.190)
Specification:
Voltage:
Up to 440 VAC
Operating Temperature:
-40°F to 185°F (-40°C to 85°C)
Foil Thickness:
6.0 µm +/- 5%
Standard Tolerance:
+/- 5%
MFD Value:
60+5
Style:
Oval
Size:
3.54x1.89x3.94
LCD60+5X440R HVAC ROUND DUAL RUN CAPACITOR
Engineered by an ISO manufacturer with over twenty years' experience in OEM capacitor fabrication, Linebacker® capacitors are manufactured by the OEM factory and are 100% in-line production tested to the same rigorous standards.
Features/Benefits
10,000 AFC pressure sensitive short circuit interrupting capability
3-year warranty from the date of purchase
Continuous life tested, oil leak tested and dielectric tested for insulation effectiveness
Life tested to 85° C operating temperature for 10,000 cycles
Manufactured with thick polypropylene foil to handle increased operating temperatures
Meets EIA-456A accelerated life test at 70° C for 60,000 hours
PCB-free oil to prevent over-heating
UL File # E352486
US and Canada UL approved (C22.2NO.190)
Specification:
Voltage:
Up to 440 VAC
Operating Temperature:
-40°F to 185°F (-40°C to 85°C)
Foil Thickness:
6.0 µm +/- 5%
Standard Tolerance:
+/- 5%
MFD Value:
60+5
Style:
Round
Size:
2.5x3.94
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO 285753A Washer Direct Drive Motor Coupler
The XPARTCO 285753A is an aftermarket replacement direct drive motor coupler (also called a motor coupling or drive coupler) compatible with a wide range of Whirlpool-family top-load washers including Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef. The motor coupler connects the drive motor shaft to the transmission — transferring the motor's power to the transmission to drive the agitator and spin the drum during wash and spin cycles. It is a deliberate weak point in the drivetrain: if the washer is overloaded, the coupler breaks apart first, protecting the far more expensive motor and transmission from damage.
This is the updated 285753A design with metal sleeves for added strength — it replaces all previous coupler styles and versions including the original 285753, 280152, 285743, and 285140. This kit includes 2 plastic coupling halves and 1 rubber isolation dampener. Dimensions approximately 2" L x 1-1/4" W x 2" H. Fits direct-drive top-load washers only — not compatible with belt-drive machines. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The XPARTCO 285753A Washer Motor Coupler fixes top-load washers that fill and drain normally but will not agitate or spin. The motor coupler connects the motor to the transmission — when it breaks, the motor runs but neither the agitator nor the drum moves. Kit includes 2 plastic coupling halves and 1 rubber dampener. Updated design with metal sleeves. Replaces all previous coupler versions including 285753, 280152, 285743, 285140. Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, Admiral, and more direct-drive top-load washers.
Common Problems This Part Fixes
Washer fills with water and drains but will not agitate or spin
Motor runs (you can hear it) but agitator and drum do not move
Washer spins slowly or incompletely — clothes still very wet after spin cycle
Loud humming or buzzing from the motor area without agitation or spin
Burning rubber or plastic smell during the wash or spin cycle
Washer shakes excessively — broken coupler causing uneven power transfer
Broken plastic or rubber pieces visible inside the bottom of the washer cabinet
Replaces Part Numbers
This motor coupler directly replaces the following OEM and cross-reference part numbers:
285753A, 1195967, 21003, 280152, 285140, 285743, 285753, 285753AVP, 3352470, 3363664, 3364002, 3364003, 62672, 62693, 661560, 80008, 8559748, AWP39583, PD00002353, AH1485646, EAP1485646, EA1485646, TJ285753, ER285753, AP3963893, PS1485646.
The 285753A replaces all previous motor coupler styles and versions. If your parts diagram shows any of the older numbers above, the 285753A is the correct current replacement.
Compatibility
This motor coupler is compatible with select direct-drive top-load washers from the following brands:
Whirlpool top-load washers (direct drive — no belt)
Kenmore / Sears top-load washers — 70 series, 80 series, 90 series, and 110 series (Whirlpool-built)
KitchenAid top-load washers
Maytag top-load washers (direct drive models)
Amana top-load washers
Roper top-load washers
Admiral top-load washers
Estate top-load washers
Crosley top-load washers
Inglis top-load washers
Magic Chef top-load washers
Important: The 285753A is for direct-drive top-load washers only — machines where the motor connects directly to the transmission without a belt. It is not compatible with front-load washers or older belt-drive top-load washers. If you can see a drive belt inside your washer cabinet, this is not the correct part.
Key Features
Connects the drive motor shaft to the transmission — transfers motor power to drive the agitator and spin drum
Intentional sacrificial part — designed to break before the motor or transmission during overload, saving far more expensive components
Updated 285753A design with metal sleeves — stronger than original all-plastic versions; replaces all previous coupler styles
Kit includes 2 plastic coupling halves and 1 rubber isolation dampener — complete assembly
Dimensions: approximately 2" L x 1-1/4" W x 2" H
Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef direct-drive washers
Replaces all previous coupler versions including 285753, 280152, 285743, and 285140
Aftermarket replacement built to OEM-equivalent quality standards
Cost-effective DIY repair — typically under $15 and 30–45 minutes of work
Product Specifications
Part Number
285753A
Part Type
Washer Direct Drive Motor Coupler (Motor Coupling Kit)
Condition
Aftermarket Replacement
Application
Direct-Drive Top-Load Washers (no belt)
Dimensions
Approx. 2" L x 1-1/4" W x 2" H
Color
Black / Off-White
Material
Rubber / Plastic / Metal (metal sleeve inserts)
Kit Includes
2 plastic coupling halves, 1 rubber isolation dampener
Compatible Brands
Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. Remove the washer's cabinet by releasing the top panel clips and removing the front panel screws — the motor and transmission are at the bottom of the machine. The motor coupler is a three-piece assembly between the motor shaft and the transmission input shaft. Pull the motor forward to release it from the mounting clips. The broken coupler pieces will likely fall out at this point — inspect the motor shaft and transmission shaft for any remaining plastic debris and clear it. Press the new rubber dampener onto the motor shaft coupling half first, then onto the transmission shaft coupling half, and snap the motor back into the mounting clips. Verify both coupler halves are seated securely and the rubber dampener is centered between them. Reassemble the front panel and top panel. Restore power and run a short cycle to confirm the agitator and spin function normally. Work gloves recommended — sharp sheet metal edges inside the cabinet. Tools needed: Phillips screwdriver, 1/4" nut driver, flat-head screwdriver, work gloves.
Frequently Asked Questions
What does the motor coupler do?
The motor coupler is a three-piece assembly — two plastic coupling halves and a rubber dampener — that connects the drive motor shaft to the transmission input shaft in direct-drive washing machines. The motor spins the coupler, which transfers that rotation to the transmission, which in turn drives the agitator and drum. The rubber dampener absorbs shock and vibration between the rigid motor and transmission shafts during direction changes. The coupler is intentionally designed as the weakest link in the drivetrain — if the washer is overloaded or the transmission seizes, the coupler breaks first to protect the far more expensive motor and transmission from damage.
My washer fills and drains but won't agitate or spin — is the motor coupler the cause?
Yes — this is the classic symptom of a broken motor coupler. Because the pump is typically driven directly by the motor before the coupler connection, a broken coupler allows the motor to run and the pump to drain normally, but neither the agitator nor the spin drum receives any power. If you can hear the motor running but nothing moves, open the washer cabinet and inspect the coupler — you will likely find broken plastic pieces at the bottom of the cabinet near the motor and transmission.
Why does the motor coupler break?
The most common cause is overloading — packing too many heavy items into the washer creates enough mechanical resistance that the coupler snaps rather than allowing the motor to be damaged. Other causes include a worn or seized transmission, a worn motor, normal wear over many years of use, or a single sudden jam caused by a foreign object. If your coupler breaks a second time shortly after replacement, inspect the transmission for signs of wear or binding — a stiff or seized transmission will continue to break new couplers.
What is the difference between 285753 and 285753A?
The 285753A is the updated current version that superseded the original 285753. The A version incorporates metal sleeve inserts in the plastic coupling halves for improved strength and durability compared to the original all-plastic design. The 285753A replaces all previous versions — including 285753, 280152, 285743, and 285140 — and is the correct part to order regardless of which older number is listed in your washer's parts diagram.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from rubber, plastic, and metal to match the dimensions and performance of the original 285753A motor coupler.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 5304519906 Dishwasher Pump and Motor Assembly
Product Overview
The XPARTCO 5304519906 Dishwasher Pump and Motor Assembly is designed to circulate water through the spray arms and ensure proper cleaning performance. This Motor & Pump Assembly is a replacement part for specific Frigidaire dishwasher models. This assembly is crucial for circulating water throughout the dishwasher during the wash and rinse cycles, ensuring that dishes are cleaned effectively. You should replace this motor and pump assembly if it becomes faulty. Common causes of a bad motor and pump assembly include electrical issues, wear and tear from regular use, or blockages caused by debris or food particles.
Quick Answer
If your dishwasher is not cleaning dishes, has weak spray pressure, makes unusual noises, or fails to circulate water, the 5304519906 pump and motor assembly may be faulty. Replacing it restores proper wash performance and water circulation.
Replaces Part Numbers
Replaces OEM part number: 5304519906, 154843901, EAP12712308, AFR18422, PD00053471, AP6840161, P154792801.
Compatibility
This pump and motor assembly is compatible with select Frigidaire, Electrolux, Kenmore, and other compatible dishwashers.
Frigidaire Dishwashers
Electrolux Dishwashers
Kenmore Dishwashers
Always verify your appliance model number before ordering.
Common Problems This Part Fixes
Dishes not getting clean
Weak or no water spray
Dishwasher making loud or grinding noise
Water not circulating during wash cycle
Key Features
Integrated pump and motor assembly
Restores strong water circulation
High-quality aftermarket replacement
Reliable and durable construction
Product Specifications
Part Number: XP5304519906
Part Type: Dishwasher Pump and Motor Assembly
Brand: XPARTCO
Condition: New
OEM / Aftermarket: Aftermarket
Application: Dishwasher Water Circulation
Troubleshooting Guide
Dishes remain dirty → Weak or failed pump motor
No spray action → Pump not circulating water
Loud noise during wash → Motor or impeller issue
When Should You Replace This Assembly?
Replace this assembly if your dishwasher is not cleaning properly, lacks water pressure, or makes abnormal noises during operation.
Installation Notes
⚠️ Disconnect power and water supply before installation. Access the pump and motor assembly from the bottom of the unit and install securely according to your dishwasher model.
Related Parts
Dishwasher Spray Arm
Water Inlet Valve
Drain Pump
Frequently Asked Questions
Will this assembly fit my dishwasher?This part fits many Frigidaire and compatible dishwashers. Always verify your model number.
What does a pump and motor assembly do?It circulates water through the dishwasher to clean dishes effectively.
What are signs of a bad pump motor?Poor cleaning, weak spray, or loud noises during operation.
Is this OEM or aftermarket?This is a high-quality aftermarket replacement part.
Shop With Confidence
Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support.
Fast Shipping Quality Tested Parts Compatibility Support
WPW10455261 Dishwasher Genuine OEM Pump and Motor Assembly
Fits specific Whirlpool, Maytag, Kenmore Dishwasher models
Description: This Dishwasher Pump & Motor is an OEM replacement part for specific Whirlpool dishwasher models. As the main component for water circulation, it contains both the water pump and motor required to power it.
Replaces Part Numbers: WPW10455261, W10455261, 2312159, W10500284, AP6021679, PS11755005.
California Residents only
WARNING: California’s Proposition 65
5040JA2004A Genuine OEM LG Refrigerator Motor Damper Grommet (Rear)
The 5040JA2004A is a genuine LG OEM rubber motor damper grommet for LG and select Kenmore refrigerators. This small rubber component mounts and isolates a fan motor from the surrounding bracket, cushioning it against vibration as the motor runs. This is the rear-position grommet; LG refrigerators typically use more than one grommet to support a fan motor from multiple points.
Made of rubber, this grommet naturally degrades over years of exposure to cold temperatures and constant vibration, eventually cracking, hardening, or losing its cushioning shape. Once it fails, the motor it supports is no longer properly isolated, and the metal motor bracket can end up in direct contact with the surrounding housing. A worn or failed grommet typically shows up as new or worsening rattling, buzzing, or vibration noise coming from the back of the refrigerator, especially noticeable when the fan motor is running. It directly replaces 5040JA2004B, 1268010, AP4635690, AH3526229, EA3526229, PS3526229, EAP3526229, and PD00027884.
Quick Answer
The 5040JA2004A Genuine OEM LG Refrigerator Motor Damper Grommet (Rear) fixes LG and select Kenmore refrigerators with new or worsening rattling, buzzing, or vibration noise from the back of the unit, especially when the fan motor is running. Rubber, rear-position grommet. Replaces 5040JA2004B, 1268010, AP4635690, AH3526229, EA3526229, PS3526229, EAP3526229, PD00027884. This grommet is used with a fan motor at the rear of the refrigerator; sources vary on whether that's the evaporator or condenser fan depending on the specific model, so confirm your model number before ordering.
Common Problems This Part Fixes
Rattling or buzzing noise from the back of the refrigerator
Vibration noise that's especially noticeable when the fan motor is running
Noise that has gradually worsened over time
Visibly cracked, hardened, or flattened rubber grommet
Motor bracket that feels loose or vibrates excessively against its housing
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This motor damper grommet directly replaces the following OEM and cross-reference part numbers:
5040JA2004A, 1268010, AP4635690, AH3526229, EA3526229, PS3526229, EAP3526229, PD00027884
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This motor damper grommet is compatible with select LG refrigerators, and also fits select Kenmore refrigerators built on the LG platform, including model numbers such as LSXS26386S00, LTCS20030S/00, LTC24380SB00, LRSCS21935SW, LFC24770ST/02, LSXS26326W/01, and Kenmore 795.79043311, 795.51089011, 795.51832412, 795.79412810, and 795.78032211.
Note: This is the rear-position grommet. LG also lists a related grommet, part number 5040JA2009B, used as a support damper for fan motors on other models — the two are not necessarily interchangeable, so confirm your exact part number and position before ordering. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine LG OEM part — factory-specified rubber compound and fit
Isolates the fan motor from its bracket, cushioning it against vibration
Resolves "rattling," "buzzing," and "vibration noise" symptoms caused by a worn or failed grommet
Rear-position grommet
Durable rubber construction designed for the refrigerator's cold operating environment
Direct drop-in replacement — no tools required on most models
Replaces 5040JA2004B, 1268010, AP4635690, AH3526229, EA3526229, PS3526229, EAP3526229, and PD00027884
Compatible with LG and select Kenmore refrigerators
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
5040JA2004A
Part Type
Fan Motor Damper Grommet — Rear
Condition
Genuine OEM
Brand
LG
Material
Rubber
Function
Isolates and cushions a fan motor from vibration at its bracket
Position
Rear
Related Part
5040JA2009B (support damper, different position/models — verify before substituting)
Repair Difficulty
Very Easy — typically no tools required
Quantity
1 damper grommet
Compatible Brands
LG, Kenmore
Installation Notes
⚠️ Unplug Refrigerator Before Starting Disconnect power at the outlet before beginning, and move perishable food to a cooler if access requires opening the freezer compartment. Wear work gloves. Access depends on your model — this grommet supports a fan motor that may be located behind the freezer's rear interior panel or in the compressor/machine compartment at the back or bottom of the unit, so check your model's service diagram for the exact location. Remove any panel screws needed to reach the motor bracket. Photograph the grommet's position and how it seats against the bracket before removing it. Gently remove the old, worn grommet from around the motor mounting post — it typically pulls or presses off without tools. Press the new 5040JA2004A grommet into the same position, seating it fully so it cushions the motor bracket evenly. Reassemble any panels removed for access, restore power, and run the refrigerator for a while to confirm the rattling or vibration noise has resolved. Tools needed: Phillips screwdriver (for panel access), work gloves.
Frequently Asked Questions
My refrigerator has developed a rattling noise from the back. Is this the grommet?
Yes, this is a common cause of exactly that symptom. Once the rubber grommet cracks, hardens, or loses its cushioning shape, the fan motor's mounting bracket is no longer properly isolated and can vibrate directly against the surrounding housing, producing a rattling or buzzing noise — especially noticeable whenever the fan motor is actively running.
Is this for the evaporator fan motor or the condenser fan motor?
Sources describe this grommet's application somewhat differently depending on the specific refrigerator model — some reference it as supporting the evaporator fan motor, others the condenser fan motor. In practice, this reflects that LG uses the same grommet design for fan motor mounting in more than one location depending on the model. Confirm your full model number against the compatibility list, or check your appliance's parts diagram, to be certain which motor this grommet supports on your specific unit.
Do I need any tools to replace this?
The grommet itself is tool-free — it simply presses into place around the motor mounting post. You will likely need a screwdriver to remove whatever panel is covering the area where the motor and grommet are located, but the grommet swap itself requires no tools.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original rubber compound and mounting fit of the motor damper grommet originally installed in your refrigerator.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
