Search results for "hvac switch"

WD21X25468 Genuine OEM GE Dishwasher Pressure Sensor Assembly The WD21X25468 is a Genuine OEM GE replacement dishwasher pressure sensor assembly compatible with a wide range of GE, GE Profile, GE Café, Hotpoint, Haier, and Monogram dishwashers in the GDF, GDT, GDP, PDT, CDT, ZDT, QDP, and HDF series. The pressure sensor monitors water pressure inside the dishwasher tub during fill and drain cycles and sends real-time readings to the electronic control board. The control board uses these readings to calculate the correct amount of water needed for each wash cycle and to confirm that the tub has drained properly before advancing to the next cycle phase. When the pressure sensor fails — or when it becomes clogged with grease, food residue, or mineral buildup — the dishwasher may not fill with water, may overfill, may stop mid-cycle, may fail to drain correctly, or may display error codes H2O or FTD (Failure to Drain). This Genuine OEM part is manufactured by GE to factory specifications. It directly replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, and 265D3356P001. Sold individually. Installs in 15–20 minutes — a screwdriver is the only tool required for most models. Quick Answer The WD21X25468 Genuine OEM GE Dishwasher Pressure Sensor Assembly fixes GE dishwashers displaying error codes H2O or FTD (Failure to Drain), not filling with water, overfilling, stopping mid-cycle, or running excessive noise from the spray arms. Monitors water level and pressure — signals the control board to fill, wash, and drain correctly. Genuine OEM. Replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, 265D3356P001. Sold individually. Compatible with GE GDF, GDT, PDT, CDT, ZDT, QDP, HDF, and related series. Common Problems This Part Fixes Error code H2O displayed — dishwasher not receiving enough water or no water at all Error code FTD (Failure to Drain) displayed — sensor not confirming tub has drained Dishwasher not filling with water when a cycle is started Dishwasher overfilling — sensor not signaling the control board to stop filling Dishwasher stopping mid-cycle without completing the wash Excessive noise during operation — sensor not accurately controlling spray arm water pressure Dishwasher requires priming with water to start (filling the tub manually before it will run) Replaces Part Numbers This pressure sensor directly replaces the following OEM and cross-reference part numbers: WD21X25468, 265D3356P001, AGE24772, AP6976524, EAP12741258, OEM20929581, PD00067609, PS12741258. Contact our support team with your model number if you need confirmation before ordering. Compatibility This pressure sensor is compatible with a wide range of dishwashers from the following GE product lines: GE dishwashers — GDF450, GDF510, GDF511, GDF535, GDF550, GDF565, GDF570, GDF630, GDF640, GDF645 series GE dishwashers — GDT530, GDT535, GDT565, GDT580, GDT605, GDT625, GDT630, GDT635, GDT645, GDT695 series GE dishwashers — GDP615, GDP645, GDP665 series GE Profile dishwashers — PDT715, PDT775, PDT785 series GE Café dishwashers — CDT800, CDT875 series GE Monogram dishwashers — ZDT800, ZDT870, ZDT925, ZDT985 series Hotpoint dishwashers — HDF310, HDF330 series Haier dishwashers (select GE-platform models) GE / Café / Profile — QDP555 series Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Monitors water pressure inside the tub throughout fill and drain cycles — signals the control board to fill to the correct level and confirm complete drainage Resolves H2O and FTD error codes on compatible GE dishwashers Sensor can also fail due to grease or mineral buildup blocking the pressure port — cleaning may resolve the issue without replacement Replaces AP6976524, PS12741258, EAP12741258, 4962334, 37640602, and 265D3356P001 Compatible with GE GDF, GDT, GDP, PDT, CDT, ZDT, QDP, HDF, and Hotpoint dishwasher series Sold individually Quick DIY repair — installs in 15–20 minutes with a screwdriver Product Specifications Part Number WD21X25468 Part Type Dishwasher Pressure Sensor Assembly (Pressure Switch) Condition Genuine OEM Application GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier Dishwashers Function Monitors tub water level and pressure — signals control board for fill and drain control Error Codes Resolved H2O (no/low water), FTD (Failure to Drain) Sold As Single sensor assembly Compatible Brands GE, GE Profile, GE Café, GE Monogram, Hotpoint, Haier Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting Disconnect power and shut off the water supply before beginning. On most compatible GE models, the pressure sensor is located near the bottom of the dishwasher tub, accessible after removing the lower front kick panel (secured by one or two screws). The sensor assembly connects to a small hose and a wiring harness connector. Tip: before replacing the sensor, remove it and inspect the pressure port and hose for grease, food residue, or mineral buildup — a clogged sensor port can cause H2O and FTD errors without the sensor itself being electrically failed. Clean the port and hose with warm water and a small brush, reinstall, and test the dishwasher. If the error codes persist after cleaning, replace the WD21X25468 sensor. To replace: disconnect the hose and wiring harness from the old sensor, unclip or unscrew the sensor from its mounting bracket, and install the new sensor in the same position. Reconnect the hose and harness, restore power and water, and run a test cycle. Tools needed: Phillips screwdriver. Frequently Asked Questions What does the dishwasher pressure sensor do? The pressure sensor monitors the water pressure — and therefore the water level — inside the dishwasher tub throughout the wash cycle. It sends continuous readings to the electronic control board, which uses the data to determine how much water to add during fill, when to stop filling, and whether the tub has drained completely before advancing to the next cycle phase. An accurate pressure sensor is essential for the dishwasher to fill to the correct level (not too much, not too little), wash with the correct spray arm pressure, and drain fully before moving on to rinse or dry cycles. What do error codes H2O and FTD mean on GE dishwashers? H2O error code on compatible GE dishwashers indicates that the dishwasher is not detecting enough water in the tub — either water is not filling at all, or the pressure sensor is not sensing the water that has filled. FTD (Failure to Drain) code indicates the dishwasher has not confirmed that the tub has drained within the expected time. Both codes can be caused by a faulty pressure sensor, a clogged sensor port, a failed fill valve, a blocked drain system, or control board issues. The pressure sensor should be inspected and tested first since it is the most accessible and commonly replaced component for these two error codes. Should I try cleaning the sensor before replacing it? Yes — absolutely. The pressure sensor on GE dishwashers can produce H2O and FTD error codes when its pressure port or connected hose becomes clogged with grease, food residue, or hard water mineral deposits — even if the sensor itself is electrically intact. Before ordering a replacement, remove the sensor, inspect the pressure port opening, and clean it thoroughly with warm water and a small brush. Flush the connected hose to clear any buildup. Reinstall and run a test cycle. If the error codes return, the sensor has electrically failed and needs replacement with the WD21X25468. My dishwasher won't fill unless I pour water in manually first — is this the pressure sensor? Yes — this is a classic symptom of a clogged or failed pressure sensor. When the sensor port is blocked, the sensor reads zero pressure (empty tub) even when the dishwasher starts. In some cases the control board interprets this as a drainage confirmation and will not initiate the fill cycle. Pouring water into the filter manually raises the physical water level enough to trigger filling. Check and clean the sensor port as described above. If cleaning does not resolve the issue, replace the WD21X25468 sensor. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same pressure sensor assembly installed in compatible GE, GE Profile, GE Café, Hotpoint, and related brand dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

LCD30+5X440R HVAC ROUND DUAL RUN CAPACITOR Engineered by an ISO manufacturer with over twenty years' experience in OEM capacitor fabrication, Linebacker® capacitors are manufactured by the OEM factory and are 100% in-line production tested to the same rigorous standards. Features/Benefits 10,000 AFC pressure sensitive short circuit interrupting capability 3-year warranty from the date of purchase Continuous life tested, oil leak tested and dielectric tested for insulation effectiveness Life tested to 85° C operating temperature for 10,000 cycles Manufactured with thick polypropylene foil to handle increased operating temperatures Meets EIA-456A accelerated life test at 70° C for 60,000 hours PCB-free oil to prevent over-heating UL File # E352486 US and Canada UL approved (C22.2NO.190) Specification: Voltage: Up to 440 VAC Operating Temperature: -40°F to 185°F (-40°C to 85°C) Foil Thickness: 6.0 µm +/- 5% Standard Tolerance: +/- 5% MFD Value: 30+5 Style: Round Size: 1.97x3.94

Read more less

XPARTCO XP311 Dryer Thermostat Kit for LG The XPARTCO XP311 is an aftermarket replacement 3-piece thermostat kit for LG electric dryers, bundling the thermal fuse, thermistor, and high-limit thermostat that work together to regulate and protect the dryer's heating system. These three components monitor heat continuously during normal operation and step in at different thresholds if something goes wrong, which is why they're commonly replaced as a set — a single overheating event or a slow age-related drift in one part can put stress on the others, and buying them together also saves a second teardown if one of the remaining parts fails soon after. This kit includes: the 6931EL3003D thermal fuse, a one-time safety device that permanently cuts power to the dryer if internal temperatures climb dangerously high; the 6323EL2001B thermistor, a temperature sensor assembly with wire harness that continuously reports drum temperature to the control board so it can regulate heat output during the cycle; and the 6931EL3001E high-limit thermostat, which automatically shuts off the heating element if the dryer's temperature exceeds safe operating limits, without needing to be replaced like the thermal fuse does. Symptoms of failure in this circuit include incomplete drying, insufficient heating time, overheating that damages clothing, and the dryer shutting down prematurely or failing to start at all. It directly replaces AP4440975, 1268366, 6931EL3003E, AH3530485, EA3530485, PS3530485 (thermal fuse); AP4441539, 1268206, 6323EL2001H, AH3529026, EA3529026, PS3529026 (thermistor); and AP4440977, 1268363, 6931EL3001B, 6931EL3001C, AH3530481, EA3530481, PS3530481, 6931EL3001F (high-limit thermostat). Quick Answer The XPARTCO XP311 Dryer Thermostat Kit fixes LG (and select Kenmore) electric dryers with incomplete drying, insufficient heat, overheating that damages clothes, or a dryer that shuts down prematurely or won't start. 3-piece kit: thermal fuse (6931EL3003D), thermistor (6323EL2001B), and high-limit thermostat (6931EL3001E). Replaces 6323EL2001B, 6931EL3001E, 6931EL3003D, and their full cross-reference sets listed below. These three parts share the same circuit and commonly fail together — replacing all three at once is standard practice when one has failed. What's In The Kit Component Part Number Function Thermal Fuse 6931EL3003D One-time safety device — permanently cuts power if the dryer overheats. Cannot be reset once blown. Thermistor 6323EL2001B Continuously senses drum temperature and reports it to the control board to regulate heat output. High-Limit Thermostat 6931EL3001E Automatically shuts off the heating element if temperature exceeds safe limits. Resets automatically, unlike the thermal fuse. Common Problems This Kit Fixes Dryer runs but clothes come out only partially dry Insufficient heating time or reduced heat output Overheating that scorches or damages clothing Dryer shuts down prematurely mid-cycle Dryer won't start at all Inconsistent drying results from cycle to cycle Dryer that recently blew a thermal fuse and needs the related components checked Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermostat kit directly replaces the following OEM and cross-reference part numbers: 6931EL3003D, 1268366, AH3530485, EA3530485, PD00001818, EAP3530485, AP4440975, PS3530485, 6323EL2001B, 1268206, 6323EL2001H, AH3529026, PD00001821, EAP3529026, EA3529026, AP4441539, PS3529026, 6931EL3001E, 1268363, 6931EL3001C, PD00023869, EAP3530481, AH3530481, EA3530481, AP4440977, PS3530481. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This kit is compatible with select LG electric dryers, and also fits select Kenmore dryers built on the LG platform, including model numbers such as: CDE3379WN DLE0332W, DLE0442G, DLE0442W, DLE0442W01 DLE1310W, DLE2101W, DLE2140W, DLE2240W DLE2512W, DLE2514W, DLE2515S, DLE2516W, DLE2522W, DLE2524W, DLE2532W DLE3733D, DLE3733S, DLE5955W Note: This kit is for LG electric dryers. Different resistance values, dimensions, and mounting methods apply across brands and models, so always verify your full model number before ordering rather than relying on physical resemblance alone. Contact our support team with your model number if you're unsure. Key Features Complete 3-piece kit — thermal fuse, thermistor, and high-limit thermostat in one purchase Addresses the full temperature-regulation and safety circuit at once, rather than piecemeal Resolves "incomplete drying," "insufficient heat," "overheating," and "premature shutdown" symptoms Thermistor ships with its wire harness included No special tools required for installation Direct drop-in replacement for all three original components Replaces the full cross-reference set for 6931EL3003D, 6323EL2001B, and 6931EL3001E listed above Compatible with LG and select Kenmore electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Kit Part Number XP311 Kit Contents 1x Thermal Fuse (6931EL3003D), 1x Thermistor (6323EL2001B), 1x High-Limit Thermostat (6931EL3001E) Condition Aftermarket Replacement Application LG Electric Dryers Thermal Fuse Type One-time use, non-resettable High-Limit Thermostat Type Automatically resetting Thermistor Includes wire harness Repair Difficulty Easy to Moderate — no special tools required Compatible Brands LG, select Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Test Before Assuming All Three Have Failed Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel or the front, depending on your model — these components are commonly mounted on or near the blower housing and heater duct assembly. Photograph the wiring connections before disconnecting anything, since the thermal fuse, thermistor, and high-limit thermostat can look similar and are easy to swap positions by mistake. Before installing the full kit, it's reasonable to test each old component with a multimeter to confirm which have actually failed — the thermal fuse and high-limit thermostat can each be checked for continuity, though replacing all three together is still standard practice given how this circuit tends to fail. Remove each old component from its mounting position, noting orientation, and disconnect its wiring. Install each new component from the kit in the same position and orientation as the part it replaces, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal heating, consistent drying, and no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), multimeter (recommended), work gloves. Frequently Asked Questions Do I really need to replace all three parts, or can I just replace the one that failed? You can test each component individually with a multimeter and replace only the ones that fail, but there's a good reason these are commonly sold and replaced together: they share the same heating circuit and tend to age or fail around the same time, especially if an overheating event caused the original failure. Replacing all three at once avoids a second teardown if one of the remaining original parts fails again soon after. What's the difference between the thermal fuse and the high-limit thermostat? They sound similar. Both protect against overheating, but they behave very differently. The high-limit thermostat is the first line of defense — it shuts off the heating element automatically if temperature climbs too high, then resets itself once things cool down, letting the dryer resume normal operation. The thermal fuse is the backup: if temperatures climb high enough that the thermostat alone doesn't prevent a dangerous overheat, the fuse permanently opens the circuit and cuts all power. Unlike the thermostat, the fuse cannot reset itself and must be physically replaced once it blows. What does the thermistor actually do, and why does it matter if it's a sensor rather than a switch? The thermistor doesn't switch anything on or off directly — it's a variable resistor whose resistance changes with temperature, and the control board reads that resistance continuously to know exactly how hot the drum is running. That ongoing feedback is what lets the control board fine-tune heat output throughout the cycle rather than just running hot or cold. A failing thermistor can cause the control to misjudge temperature, leading to insufficient heat, inconsistent drying, or the control cutting the cycle short. My dryer blew a thermal fuse. Should I get this whole kit instead of just the fuse? It's worth considering, especially since a blown thermal fuse usually means the dryer actually overheated at some point — and that same overheating event can stress the thermistor and high-limit thermostat even if they haven't failed outright yet. Also worth checking regardless of which parts you replace: restricted exhaust venting is the most common root cause of dryer overheating, so inspect and clean the vent ducting when you do this repair, or the new parts may face the same stress that damaged the originals. Is this an OEM or aftermarket kit? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine LG OEM kit, but each component is manufactured to match the electrical specifications, resistance values, and mounting configuration of the original 6931EL3003D thermal fuse, 6323EL2001B thermistor, and 6931EL3001E high-limit thermostat used in compatible LG electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine Whirlpool WPW10392132 Refrigerator Defrost Thermostat - Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Amana Product Description Maintain optimal cooling with the Genuine Whirlpool WPW10392132 Refrigerator Defrost Thermostat. This OEM defrost thermostat is designed for select Whirlpool, Kenmore, KitchenAid, Maytag, and Amana refrigerators, monitoring evaporator coil temperature to regulate the defrost cycle, preventing frost buildup and ensuring efficient cooling. It addresses issues like frost accumulation, warm refrigerator temperatures, or freezer not cooling properly, delivering reliable performance as an authentic Whirlpool part. Note: Includes one defrost thermostat with two-wire connector. Disconnect power before installation. Check defrost heater and related components for optimal performance. Replaces part numbers: WPW10392132, AP6020798, W10392132, PD00028150, EAP11754118, 2118359, PS11754118. Compatibility: Compatible with models including but not limited to: Whirlpool: ED5FVGXWS00, ED5VHGXMB10, ED5VHGXML10, GD5DHAXVY00, WRS325FDAM02 Kenmore: 106.51132210, 106.51133210, 106.51173310 KitchenAid: KSRJ25FXMS00, KSRL25FXMT00 Maytag: MSD2559XEM01, MFI2569VEM10 Amana: ASD2522WRB02, ASD2522WRW01 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, KitchenAid, Maytag, and Amana refrigerators. ❄️ Specifications: OEM defrost thermostat, two-wire connector. 💪 Reliable Performance: Authentic Whirlpool part ensures long-lasting durability. 🛠️ Easy Installation: Requires screwdriver, pliers, work gloves; typically installed in 20–30 minutes. 🛡️ Effective Fixes: Resolves frost buildup, warm refrigerator temperatures, or freezer not cooling properly. Product Specification Part Number: Genuine Whirlpool WPW10392132 Component Type: Refrigerator defrost thermostat Material: Metal and plastic with sealed sensor Electrical Specs: 120V compatible Mounting: Clip-mounted on evaporator coil Operating Conditions: Suitable for low-temperature refrigerator environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the refrigerator from the power source before installation. Shop for high-quality Genuine appliance parts with a 30-day return policy. Keep your refrigerator cooling efficiently today! Add to cart now for a reliable fix!

Read more less

5301EL1001J Dryer Genuine Heating Element Fits Specific LG Dryer Models. 240V, 5400W complete assembly with housing and thermostats Replaces Part Numbers: 5301EL1001J, 5301EL1001A, 1377645, AEG72910307, AH3527791, AP4439759, EA3527791, PS3527791, 5301EL1001H, 1377645, 5301EL1001E, 5301EL1001G, 5301EL1001S, 5301EL1001U, 5301EL1001W, AH3527790, AP5072170, EA3527790, PS3527790, AEG72910301, AP5669354, AEG72910309, AP7211081. Description:  This Heater Assembly is a Genuine OEM part for specific LG dryer models. This component is responsible for generating the heat required to dry clothes effectively. It consists of a heating element and necessary components that work together to maintain the desired drying temperature, ensuring clothes come out dry and ready to wear.  Causes of a bad heater assembly can include wear and tear from regular use, overheating, electrical issues, or damage to the heating element itself. A malfunctioning heater assembly can lead to inefficient drying or no heat at all. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.go

Read more less

XPARTCO DC96-01703H Washer Water Pressure Switch - Compatible with Samsung Washers Product Description Ensure your Samsung washer operates flawlessly with the replacement DC96-01703H Washer Water Pressure Switch. This replacement part is designed for select Samsung washing machines, providing precise water level control to prevent overfilling, underfilling, or water leakage. It resolves issues like error codes, inconsistent water levels, or failure to start wash cycles, delivering reliable performance for your appliance. Note: Disconnect power and water supply before installation. Verify model compatibility for proper fit. Replaces part numbers: DC96-01703H, PD00030634, EAP8764044, AP5799898, 3997570, PS8764044. Compatibility: Compatible with models including but not limited to: Samsung: WA48J7700AW/A2, WA48H7400AW/A2, WA50F9A7DSP/A2, WA52M7750AV/A4, WA56H9000AP/A2 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand Compatibility: Fits select Samsung washing machines. 🔥 Specifications: Water pressure switch with electrical connectors and 28" hose attachment. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires screwdriver, pliers; typically installed in 10–15 minutes. 🛡️ Effective Fixes: Resolves water level issues, error codes, and improper filling. Product Specification Part Number: XPDC96-01703H Component Type: Washer water pressure switch Mounting: Secures to washer control panel with screws or clips Operating Conditions: Suitable for washer environments Installation Notes: Safety First: Disconnect the washer from power and water sources before installation. Follow the owner’s manual for guidance. Shop for high-quality replacement appliance parts with a 30-day return policy. Fix your washer today! Add to cart now for a reliable solution!

Read more less

XPARTCO XP6974 Dryer Thermostat Kit Replaces WP3387134, WP3392519, W10900067, 279816 The XPARTCO XP6974 is an aftermarket dryer thermostat kit containing four thermal components for Whirlpool-family electric and gas dryers including Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef. The kit includes the cycling thermostat (WP3387134), thermal fuse (WP3392519), high-limit thermostat and thermal cut-off kit (279816 / W10900067) — the complete set of heat-sensing and safety components that regulate dryer temperature and prevent dangerous overheating. These four components work together to control and protect the dryer's heating system. When any one of them fails, the dryer may produce no heat, overheat, run too long, or stop mid-cycle. Because a failed thermal fuse is almost always caused by an underlying overheating condition that also stresses the other components, replacing all four together in a single repair is the recommended approach. Includes all wiring hardware needed for installation. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO XP6974 Dryer Thermostat Kit fixes Whirlpool-family dryers that produce no heat, overheat, take too long to dry, or stop mid-cycle. Includes all four thermal components: cycling thermostat (L155-25), thermal fuse (196°F), high-limit thermostat (L250-80), and thermal cut-off (309°F). Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef electric and gas dryers. Common Problems This Kit Fixes Dryer produces no heat — thermal fuse or high-limit thermostat has blown Dryer takes multiple cycles or very long time to dry clothes Dryer overheats — clothes or drum too hot to touch after a cycle Dryer shuts off mid-cycle and will not restart Dryer tumbles normally but generates no heat at all Dryer runs too long because cycling thermostat is not regulating temperature Repeated thermal fuse failures — underlying thermostat fault causing recurring overheating What's in the Kit Part 1 of 4 WP3387134 Cycling Thermostat Rated L155-25 · Monitors drum air temperature and cycles the heating element on and off to maintain the set drying temperature · Located on the exhaust duct or blower housing · Should show closed continuity at room temperature Part 2 of 4 WP3392519 Thermal Fuse Opens at 196°F (91°C) · One-time safety device located on the exhaust duct · Permanently interrupts power to the heating element if the dryer overheats · Cannot be reset — must be replaced if blown · Most common cause of no-heat in Whirlpool-family dryers Part 3 of 4 High-Limit Thermostat (279816 / W10900067) Rated L250-80 · Mounted on the heating element housing · Opens at approximately 250°F to cut power to the heating element if temperature exceeds safe limits · Resets automatically when it cools · Should show closed continuity at room temperature Part 4 of 4 Thermal Cut-Off Fuse (3977393 / 279816 kit) Opens at 309°F · Backup one-time safety device on the heating element housing · Permanently interrupts power to the heating element if the high-limit thermostat fails to open · Cannot be reset — must be replaced if blown Replaces Part Numbers WP3387134 Cycling Thermostat cross-references: WP3387134, WP3387134VP, 3387134, 3387135, 3387139, 306910, 3-6910, ET187, AP6008270, PS11741405 WP3392519 Thermal Fuse cross-references: WP3392519, WP3392519VP, 3392519, 3388651, 694511, 80005, ET401, G4AP0500, AP6008325, PS11741460 279816 High-Limit Thermostat and Thermal Cut-Off Kit cross-references: 279816, 279816VP, W10900067, 3977393, 3977767, WP3977767, WP3977767VP, 3399848, 3399693, 2651, AP3094244, AH334299, EA334299, EAP334299, PS334299 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat kit is compatible with select gas and electric dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (Whirlpool-built models) Maytag dryers (gas and electric) Amana dryers KitchenAid dryers Roper dryers Admiral dryers Estate dryers Crosley dryers Inglis dryers Magic Chef dryers Important: If your thermal fuse has blown, always check for the root cause before replacing — a clogged exhaust vent is the most common cause of dryer overheating. Clean the full length of the exhaust duct before or after this repair. If the vent is clear, a failed cycling thermostat or high-limit thermostat is likely the root cause. Key Features Complete 4-part thermal kit — covers the cycling thermostat, thermal fuse, high-limit thermostat, and thermal cut-off in a single repair Cycling thermostat (L155-25) — regulates drum temperature to maintain consistent, efficient drying Thermal fuse (196°F) — one-time safety device that permanently interrupts heat if the dryer overheats High-limit thermostat (L250-80, ~250°F) — cuts power to the heating element when temperature exceeds safe limits; auto-resets Thermal cut-off (309°F) — backup one-time safety device protecting against heating element runaway Replacing all four parts together ensures the complete thermal circuit is renewed — prevents recurrence if a failing thermostat caused the fuse to blow Includes all wiring hardware for installation Compatible with 11 major appliance brands on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Kit Part Number XP6974 Condition Aftermarket Replacement Application Gas and Electric Dryers Kit Includes 1x WP3387134 Cycling Thermostat, 1x WP3392519 Thermal Fuse, 1x High-Limit Thermostat (L250-80), 1x Thermal Cut-Off Fuse (309°F), wiring hardware Cycling Thermostat Rating L155-25 (closes at 155°F, opens at 25°F differential) Thermal Fuse Trip Temp 196°F (91°C) — one-time, non-resettable High-Limit Thermostat Rating L250-80 (opens at ~250°F) — auto-resets Thermal Cut-Off Trip Temp 309°F — one-time, non-resettable Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef Installation Notes ⚠️ Unplug Dryer and Shut Off Gas Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the back panel of the dryer to access the heating element housing and exhaust duct. The thermal fuse (WP3392519) and cycling thermostat (WP3387134) are located on the exhaust duct or blower housing — disconnect the wires, unscrew the mounting screws, and install the new parts in the same positions. The high-limit thermostat and thermal cut-off (279816 kit) are located on the heating element housing — disconnect the wires and unscrew the mounting screws to remove the old parts and install the new ones. Reconnect all wires to the correct terminals — take a photo before disconnecting to reference during reinstallation. Reassemble the back panel, restore power, and run a test cycle to verify heat. Tip: Before running the dryer, also clean the full length of the exhaust duct — a clogged vent is the most common root cause of dryer overheating and repeated thermal fuse failures. Tools needed: Phillips screwdriver, 1/4" nut driver, needle-nose pliers. Frequently Asked Questions What does each part in this kit do? The cycling thermostat (WP3387134) monitors the air temperature in the exhaust duct and cycles the heating element on and off to maintain the correct drying temperature — it is the part that controls how hot the dryer gets during normal operation. The thermal fuse (WP3392519) is a one-time safety device that permanently cuts power to the heating element if the dryer overheats above 196°F — it is the most common cause of no-heat in Whirlpool-family dryers. The high-limit thermostat opens at approximately 250°F to cut heating element power if temperature gets too high, and resets automatically when it cools. The thermal cut-off is a backup one-time fuse on the heating element that opens at 309°F if the high-limit thermostat fails to protect the heater. Why should I replace all four parts instead of just the one that failed? When a thermal fuse blows, it almost always blew because the dryer overheated — and that overheating event put significant stress on all the other thermal components as well. A failing cycling thermostat is the most common cause of repeated thermal fuse failures: if the cycling thermostat stops regulating temperature correctly, the dryer runs too hot, the high-limit thermostat is repeatedly stressed, and the thermal fuse eventually blows. Replacing just the fuse without replacing the cycling thermostat means the same overheating will blow the new fuse. Replacing all four parts at once eliminates that risk in a single repair. How do I test these parts with a multimeter? Set the multimeter to continuity or resistance mode. The thermal fuse (WP3392519), cycling thermostat (WP3387134), and high-limit thermostat should all show closed continuity (near-zero resistance) at room temperature. The thermal cut-off should also show closed continuity at room temperature. Any part that reads open (no continuity / infinite resistance) at room temperature has failed and needs to be replaced. A blown thermal fuse or cut-off will always read open — they are one-time devices and cannot reset. What causes the thermal fuse to blow repeatedly? The most common cause by far is a clogged exhaust vent — lint accumulation inside the dryer duct restricts airflow, causing heat to build up inside the dryer cabinet until the thermal fuse trips. Always clean the full length of the exhaust duct before and after replacing these parts. Other causes include a failing cycling thermostat that is not regulating temperature correctly, a stuck heating element relay, or a dryer placed in an enclosed space without adequate ventilation. Is this kit compatible with both electric and gas dryers? Yes — the XP6974 kit is compatible with both electric and gas Whirlpool-family dryers. Both types use the same cycling thermostat (WP3387134) and thermal fuse (WP3392519). The high-limit thermostat and thermal cut-off (279816 kit) are located on the heating element in electric models and on the burner assembly area in gas models. Always verify your specific model number before ordering to confirm all four parts apply to your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

EXPFFSB Microwave Door Switch and Fuse Kit – Replaces FSSBA016KIT & 5303319559 – Compatible with Frigidaire & Electrolux Microwaves Product Description Restore proper microwave safety operation with the EXPFFSB Microwave Door Switch and Fuse Kit. This aftermarket repair kit includes the essential components needed to fix common microwave door and power issues, including one door switch and one ceramic fuse. A faulty door switch or blown fuse can prevent the microwave from starting, cause intermittent power loss, or trigger safety shutdowns. Replacing both components together helps restore reliable microwave operation and prevents repeat failures. This kit is engineered to match original fit and electrical performance while offering a cost-effective alternative to OEM parts. This kit includes: 1 Microwave Door Switch 1 Microwave Fuse Replaces Part Numbers FSSBA016KIT, FFS-BA016/KIT, PS2422854, FFSBA016/KIT-R, FFSBA016/KIT, FFSBA016KIT, 5303319559, 634759, 75303319559, PD00026535, EAP466978, AH466978, EA466978, AP2148482, PS466978, 5304467695, 1467286, 75304467695, AH2339493, EA2339493, AP4357598, PS2339493, 5304461109, 1260958, 75304461109, AH1765534, EA1765534, AP4057424, PS1765534, 4313105, 565130, 8185302, AH358056, EA358056, AP3032745, PS358056, 5304479020, 1793730, AH3409702, EA3409702, AP4588054, PS3409702 Compatibility This microwave door switch and fuse repair kit fits select Frigidaire, Electrolux, Gibson, Kelvinator, and Kenmore (Frigidaire-manufactured) microwaves. Common compatible models include (but are not limited to): Frigidaire FFMV1645TS Frigidaire FGMV176NTF Always verify your microwave’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Complete Repair Kit – Includes door switch and microwave fuse ⚡ Restores Microwave Power – Fixes no-start and power loss issues 🔒 Door Safety Function – Ensures proper door interlock operation 🧩 Direct-Fit Components – Designed for straightforward installation 💰 Cost-Effective Repair – Replace two common failure parts at once 📐 Product Specification Kit Number: EXPFFSB Includes: (1) Microwave Door Switch (1) Microwave Fuse Application: Microwave door interlock and circuit protection Fuse Type: Ceramic microwave line fuse Quality Level: Aftermarket replacement kit (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver ⚠️ Safety First: Unplug the microwave before servicing to avoid electrical shock. Microwaves contain high-voltage components—ensure the capacitor is discharged before handling internal parts. Basic Steps: Disconnect microwave power. Remove the outer cabinet or control panel to access the door switch assembly. Replace the faulty door switch. Locate and replace the blown fuse. Reassemble the microwave and restore power. Test door operation and heating function. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Replacement Parts 🔄 30-Day Return Policy Restore microwave safety and reliable operation — Add to Cart Now for a complete repair solution!

Read more less

XPARTCO W10613606 Refrigerator Compressor Start Relay and Capacitor The XPARTCO W10613606 is an aftermarket replacement compressor start relay and capacitor assembly compatible with a wide range of Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Jenn-Air, Admiral, Crosley, Dacor, Hardwick, Inglis, Litton, and Magic Chef refrigerators. The start relay is a small but critical electrical component that plugs directly onto the compressor terminals and provides the initial power surge needed to start the compressor motor. Once the compressor reaches operating speed, the relay drops out — leaving the compressor to run on its own. The capacitor (rated 15µF ±5%, 250VAC) works alongside the relay to store and release the burst of electrical energy needed on startup. When the start relay fails, the compressor cannot start — causing the refrigerator to stop cooling entirely. A failed relay typically produces a clicking sound every few minutes as the compressor tries and fails to start, followed by a short rest, then another attempt. This kit includes both the start relay and the CBB61 capacitor. It directly replaces W10416065, 8208290, 8208368, C8931605, 67003186, 67005560, 67005561, 67005562, 67003764, 8171210, and several additional cross-reference numbers. Installs in under 15 minutes — no tools required in most cases. Quick Answer The XPARTCO W10613606 Refrigerator Compressor Start Relay and Capacitor fixes refrigerators that are not cooling, are too warm, or are making a repeated clicking sound every few minutes as the compressor tries to start. Plugs directly onto the compressor terminals. Kit includes start relay and 15µF 250VAC CBB61 capacitor. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, and more. Replaces W10416065, 8208290, C8931605, 67005560, and more. No tools required — installs in under 15 minutes. Common Problems This Part Fixes Refrigerator not cooling — compressor not running Freezer section too warm or not freezing Both refrigerator and freezer compartments gradually warming up Repeated clicking sound every 2–5 minutes from behind or underneath the refrigerator Compressor hums briefly then shuts off without reaching operating temperature Refrigerator runs but cannot maintain set temperature Shaking the start relay reveals a rattling sound inside — confirms internal failure Replaces Part Numbers This start relay and capacitor kit directly replaces the following OEM and cross-reference part numbers: W10613606, 67005560, 3023300, 67003186, 67003764, 67005561, 67005562, W10416065, 8171210, 8208290, 8208368, W10244032, 302TFBYY, SSP14R302TFR,  AWP41206, C8931605, PD00004905, EAP8746522, AP5787784, PS8746522. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This start relay and capacitor is compatible with select refrigerators from the following brands: Whirlpool refrigerators (side-by-side, French door, bottom-freezer) Kenmore / Sears refrigerators (select Whirlpool-built models) Maytag refrigerators KitchenAid refrigerators Amana refrigerators Jenn-Air refrigerators Admiral refrigerators Crosley refrigerators Dacor refrigerators Hardwick refrigerators Inglis refrigerators Litton refrigerators Magic Chef refrigerators Important: Always verify your refrigerator's model number and compare the old relay's shape and terminal configuration to the new part before installing. Some models may require trimming the wire connector tabs for a proper fit. Contact our support team with your model number if you need confirmation before ordering. Key Features Provides the initial electrical surge needed to start the compressor motor — without it, the compressor cannot run and the refrigerator cannot cool Kit includes both the start relay and the CBB61 run capacitor (15µF ±5%, 250VAC) — everything needed in one package Plugs directly onto the compressor terminals — no wiring or soldering required in most cases Quick rattle test — shake the old relay; if it rattles, the internal contacts have failed and it needs replacement Replaces W10416065, 8208290, C8931605, and over a dozen additional cross-reference part numbers Compatible with 13 major appliance brands on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards Fast DIY repair — installs in under 15 minutes, no tools required in most cases Product Specifications Part Number W10613606 Part Type Refrigerator Compressor Start Relay and Capacitor Kit Condition Aftermarket Replacement Application Refrigerator Compressor (side-by-side, French door, bottom-freezer) Capacitor Type CBB61 Run Capacitor Capacitor Rating 15µF ±5%, 250VAC Kit Includes 1x Start relay, 1x CBB61 capacitor Installation Plug-in — no tools required in most cases Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Jenn-Air, Admiral, Crosley, Dacor, Hardwick, Inglis, Litton, Magic Chef Installation Notes ⚠️ Unplug Refrigerator Before Starting Unplug the refrigerator from the power outlet before beginning. Move the refrigerator away from the wall to access the rear or lower back panel. Remove the rear access panel by unscrewing the retaining screws to expose the compressor. The compressor is a large black dome-shaped component — the start relay and capacitor assembly plugs onto the side terminals. Grip the old relay firmly and pull it straight off the compressor pins. Shake it — if it rattles, the internal contacts have failed and replacement is confirmed. Compare the old relay to the new W10613606 to confirm the terminal layout matches. Align the new relay with the compressor pins and press it firmly on. Reinstall the access panel, restore power, and listen for the compressor to start and run normally within a few minutes. Note: Some models may require trimming the wire connector tabs or reversing the connector orientation for a proper fit — do not force the connection. Tools needed: Phillips screwdriver (for panel access only). Frequently Asked Questions What does the compressor start relay do? The start relay plugs onto the compressor terminals and provides the brief but powerful surge of electrical current needed to start the compressor motor from a standstill. Once the compressor reaches operating speed — usually within a second or two — the relay drops out and the compressor runs on its own. Without a working start relay, the compressor cannot start at all, and the refrigerator stops cooling. The capacitor works alongside the relay to store and deliver the extra energy needed on startup. How do I know if my start relay has failed? The most reliable quick test is the rattle test: unplug the refrigerator, pull the start relay off the compressor, and shake it near your ear. A working relay is silent. A failed relay will rattle — the internal contacts have broken free and are loose inside the casing. Another sign is a repeated clicking sound every 2–5 minutes from the back of the refrigerator, where the compressor attempts to start, fails, trips the overload protector, rests, and tries again. If the fridge is warm and you hear clicking, check the relay first. What is the difference between the start relay and the capacitor? The start relay is the switching device that connects and disconnects the start winding of the compressor motor during startup. The capacitor stores a charge and releases it during startup to give the motor the additional torque it needs to get moving under load. Together they work as a startup system for the compressor. This kit includes both — replacing both at the same time ensures the complete startup circuit is fresh and reliable. My fridge is still not cooling after replacing the start relay — what else could it be? If replacing the start relay does not restore cooling, other possible causes include a failed compressor (the compressor runs but no longer builds pressure), a refrigerant leak in the sealed system, a failed start capacitor (if not replaced along with the relay), a bad overload protector, or a faulty main control board. Listen carefully after installing the new relay — if the compressor now starts and runs but the fridge still doesn't cool after several hours, a sealed system issue or refrigerant problem is likely and will require a certified technician. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications and terminal configuration of the original W10613606 start relay and capacitor assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 279769 Dryer Thermostat Kit The XPARTCO 279769 is an aftermarket replacement thermal cut-off and high-limit thermostat kit for Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers. This kit bundles two components that guard against overheating at different thresholds: the 3390291 high-limit thermostat (rated L250-80F) monitors internal temperature and interrupts power at approximately 250°F to prevent overheating, then resets itself automatically once the dryer cools — no replacement needed after each trip. The 3977394 thermal cut-off fuse is the backup: rated at 352°F, it's a one-time safety device that permanently opens the circuit if temperatures climb high enough that the thermostat alone didn't prevent an overheat. These two parts are sold together and should be replaced together as a set, since they protect the same circuit and tend to be stressed by the same underlying problem. Whirlpool's own guidance is direct: when the thermal cut-off fails, it usually indicates a venting problem, and failing to correct that airflow issue will cause repetitive failures even with new parts installed. Symptoms include the dryer not heating, clothes coming out extremely hot, or the dryer not running at all. This kit is commonly used alongside heating element 4391960. It directly replaces 279769, 279548, 2796769, 279769VP, 2821, 2004, 3387812, 3389946, 3398671, 3977394, 695563, 80001, SET184, SET198, TJSET198, ET184, AP3094224, AH334278, EA334278, EAP334278, PD00002485, PS334278, WP3390291, AP6008306, 3390291, 696397, and PS11741441. As an aftermarket replacement, the 279769 kit is built to OEM-equivalent quality standards. Quick Answer The XPARTCO 279769 Dryer Thermostat Kit fixes Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers with no heat, no power at all, or clothes coming out dangerously hot. Includes the 3390291 high-limit thermostat (250°F, auto-resetting) and the 3977394 thermal cut-off fuse (352°F, one-time). Replaces 279548, 2796769, 279769VP, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AP3094224, PS334278, WP3390291, AP6008306, 3390291, 696397, PS11741441. Always inspect and clean the exhaust venting when replacing this kit — a blown thermal fuse is a symptom of restricted airflow, and skipping the vent check leads to repeat failures. What's In The Kit Component Rating Function 3390291 High-Limit Thermostat L250-80F (~250°F) Interrupts power to prevent overheating, resets automatically once the dryer cools. 3977394 Thermal Cut-Off Fuse 352°F One-time backup safety device — permanently opens the circuit if temperature exceeds safe limits. Cannot reset. Common Problems This Kit Fixes Dryer won't start at all — no lights, no tumble, no response Dryer runs but produces no heat Clothes coming out extremely hot, hot enough to be uncomfortable to handle Dryer that stopped working suddenly after running unusually hot Repeated thermal cut-off failures on a dryer with a known venting issue Dryer that shuts off prematurely mid-cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermostat kit directly replaces the following OEM and cross-reference part numbers: 279769, 2004, 279548, 2796769, 279769VP, 2821, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AH334278, EA334278, AP3094224, OEM9282681, SET184, SET198E, AP334278, L250-80F, PS334278, AWP39149, PD00002485. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat kit is compatible with select Whirlpool electric dryers, and also fits select Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral dryers built on the Whirlpool platform, including model numbers such as: 7MWET4027HW0 WET3300XQ0 WET4027EW0, WET4027EW1 WET4027HW0, WET4027HW1, WET4027HW2 WETLV27FW0, WETLV27HW0, WETLV27HW1, WETLV27HW2, WETLV27HW3 YWET4027EW1, YWET4027HW0, YWET4027HW1, YWET4027HW2 Note: This kit was used on Whirlpool-built electric dryers primarily from 1985 to 1995. Always verify your full model number before ordering, since Whirlpool used several different thermostat and fuse designs across its dryer lineup over the years. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement built to match Whirlpool's factory-specified thresholds for both components 2-piece kit: 3390291 high-limit thermostat (250°F, auto-resetting) and 3977394 thermal cut-off fuse (352°F, one-time) Resolves "no heat," "no power at all," and "clothes coming out extremely hot" symptoms Addresses two overheat-protection thresholds in the same circuit at once Commonly used alongside heating element 4391960 Direct drop-in replacement for both original components Replaces 279548, 2796769, 279769VP, 3387812, 3389946, 3398671, 3977394, 695563, 80001, AP3094224, PS334278, WP3390291, AP6008306, 3390291, 696397, and PS11741441 Compatible with Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Kit Part Number 279769 Kit Contents 1x High-Limit Thermostat (3390291), 1x Thermal Cut-Off Fuse (3977394) OEM Part Number 279769 Condition Aftermarket Replacement Brand Whirlpool High-Limit Thermostat Rating L250-80F (~250°F, auto-resetting) Thermal Fuse Rating 352°F (one-time, non-resettable) Companion Heating Element 4391960 (commonly used together) Repair Difficulty Easy to Moderate — basic tools required Compatible Brands Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, Admiral Installation Notes ⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel, near the heating element and blower housing where both components are mounted. Photograph the wiring connections before disconnecting anything, since the thermostat and fuse can be easy to swap positions by mistake. Remove each old component from its mounting position, noting orientation, and disconnect its wiring. Before reassembling, fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. When the thermal cut-off fails, it usually indicates a venting problem, and failing to correct that airflow issue will cause repetitive failures even with these new parts installed. Install the new 3390291 thermostat and 3977394 thermal fuse from this kit in the same positions as the parts they replace, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), work gloves. Frequently Asked Questions My clothes are coming out extremely hot, hot enough to burn my hands. Is this the right kit? Yes, this is a documented symptom this kit addresses. If the high-limit thermostat fails to regulate temperature correctly, the dryer can run far hotter than it should, producing dangerously hot clothing at the end of a cycle. Whirlpool's own parts support has specifically pointed customers with this exact complaint toward this kit. Stop using the dryer if you notice this symptom and replace both components promptly. Why do I need to replace both the thermostat and the fuse together? These two parts protect the same circuit at different thresholds and tend to fail from the same underlying cause. If the high-limit thermostat isn't regulating temperature correctly, the thermal fuse often ends up blowing as the backup safety measure. Replacing only one risks the other failing again shortly after, so they're sold and serviced together as a set. I replaced this kit and the dryer failed again. What should I check? This is a strong sign the underlying cause — almost always restricted airflow — was never addressed. Thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. Failing to correct a venting issue will cause repetitive failures of this kit even when it's brand new. Should I replace the heating element at the same time? It's worth considering if your dryer's heating element (commonly 4391960 on compatible models) is original and has been running alongside a failing thermostat, since sustained overheating can stress the element as well. It's not required, but since you'll already have the panel open for this repair, it's a reasonable time to inspect the element for visible damage. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the temperature thresholds and mounting configuration of the original 279769 high-limit thermostat and thermal cut-off fuse kit used in compatible Whirlpool, Kenmore, Roper, KitchenAid, Maytag, Amana, Estate, Crosley, and Admiral electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

LCD60+5X440 HVAC OVAL DUAL RUN CAPACITOR Engineered by an ISO manufacturer with over twenty years' experience in OEM capacitor fabrication, Linebacker® capacitors are manufactured by the OEM factory and are 100% in-line production tested to the same rigorous standards. Features/Benefits 10,000 AFC pressure sensitive short circuit interrupting capability 3-year warranty from the date of purchase Continuous life tested, oil leak tested and dielectric tested for insulation effectiveness Life tested to 85° C operating temperature for 10,000 cycles Manufactured with thick polypropylene foil to handle increased operating temperatures Meets EIA-456A accelerated life test at 70° C for 60,000 hours PCB-free oil to prevent over-heating UL File # E352486 US and Canada UL approved (C22.2NO.190) Specification: Voltage: Up to 440 VAC Operating Temperature: -40°F to 185°F (-40°C to 85°C) Foil Thickness: 6.0 µm +/- 5% Standard Tolerance: +/- 5% MFD Value: 60+5 Style: Oval Size: 3.54x1.89x3.94

Read more less

XPARTCO WE4M137 Dryer High Limit Thermostat The XPARTCO WE4M137 is an aftermarket replacement high limit thermostat for GE, Hotpoint, and Kenmore dryers. Mounted on the upper right side of the heater housing, this safety thermostat monitors the temperature of the heating circuit and cuts power to the heating element (and in some conditions the motor) if the dryer runs hotter than it should — typically from restricted airflow, a clogged vent, or a failing cycling thermostat. Unlike a one-time thermal fuse, this is an auto-resetting high limit thermostat (rated L315-65F): it opens at approximately 315°F to stop overheating, then automatically closes again once the unit cools down, without needing to be replaced after each trip. This is a direct-fit aftermarket replacement built to the same temperature rating and mounting as the original thermostat. If this component trips repeatedly, it's worth checking the underlying cause of the overheating at the same time — a clogged lint trap or restricted exhaust vent is the most common root cause. Quick Answer The XPARTCO WE4M137 High Limit Thermostat fixes a GE, Hotpoint, or Kenmore dryer that shuts off a few minutes into a heat cycle, stops early and won't restart until it cools down, or cycles on and off intermittently. Auto-resetting, rated to open at approximately 315°F. Classic symptom: dryer runs fine for a few minutes then quits on heat, and won't restart again until it's had time to cool. Common Problems This Part Fixes Dryer shuts off a few minutes into a heat-dry cycle Dryer stops early and won't restart until it cools down Intermittent shutdowns during the drying cycle Clothes coming out damp because the cycle keeps cutting short Dryer won't start at all if the thermostat has failed in an open position Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This thermostat directly replaces the following part numbers: WE4M137, WE4M457, 276438, WE04M0137, WE04X25197, 559C131G04, AGE25626, AH267900, AP2042565, EAP267900, EA267900, PD00001228, PS267900 These numbers span several generations of GE's own part numbering for this thermostat as model lines and sub-assemblies were updated — all are the correct replacement for this component regardless of which number appears on your dryer's parts diagram. Compatibility This thermostat is compatible with 28+ GE, Hotpoint, and Kenmore dryer models, including: Kenmore 2661532110, GE 2661532210 Numerous additional GE, Hotpoint, and Kenmore dryer and washer-dryer combo models Note: This thermostat has also been referenced for some Fisher & Paykel dryer applications in sourcing, though we were not able to confirm a specific Fisher & Paykel model list. Confirm your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering. Key Features Direct-fit aftermarket high limit thermostat for GE-built dryers Auto-resetting design — no need to replace after each trip, unlike a one-time thermal fuse Rated to open at approximately 315°F to prevent overheating damage Resolves early-shutoff, won't-restart-until-cool, and intermittent cycling symptoms Fits 28+ GE, Hotpoint, and Kenmore dryer and washer-dryer combo models Straightforward swap — typically 15–30 minutes with basic hand tools Product Specifications Part Number XPWE4M137 OEM Part Number WE4M137 Part Type Dryer High Limit Thermostat (Auto-Reset) Condition Aftermarket Replacement Temperature Rating L315-65F (Opens ~315°F, Auto-Resets on Cooling) Location Upper Right Side of Heater Housing Application GE, Hotpoint & Kenmore Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. Remove the dryer's rear or front panel per your model's service guide to access the heater housing — the thermostat is mounted on its upper right side. Disconnect the wire terminals from the old thermostat, noting their positions, and remove the mounting screw holding it in place. Install the new thermostat in the same position and reconnect the wire terminals. Before closing the dryer back up, clean out the lint trap and check the exhaust vent for restrictions — a clogged vent is the most common cause of this thermostat tripping repeatedly, and clearing it now can prevent a repeat failure. Frequently Asked Questions My dryer shuts off a few minutes into the cycle and won't restart — is this the part I need? Yes, this is a classic symptom of a failing high limit thermostat. It's designed to cut power when the dryer overheats and automatically reset once things cool down, so if your dryer won't restart until it's had time to sit, this thermostat is a likely cause. Is this a one-time fuse like the thermal fuse, or does it reset itself? This is an auto-resetting thermostat, not a one-time thermal fuse. It opens to cut power when the dryer overheats, then closes again automatically once the unit cools — it doesn't need to be replaced every time it trips. If yours has failed and won't reset or close again, that's when replacement is needed. Why does my dryer keep tripping this thermostat? Repeated tripping is usually caused by restricted airflow — a clogged lint trap, a crushed or blocked exhaust duct, or a bird's nest or lint buildup in the outside vent hood — or a failed cycling thermostat elsewhere in the heating circuit. Clear the airflow path when you replace this thermostat, or the new one may trip again. How do I test if this thermostat has failed? With the dryer unplugged, you can test the thermostat with a multimeter for continuity across its terminals at room temperature. No continuity when it should be closed (cool) is a sign it has failed and needs replacement. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less