Search results for "Gas Valves"

XPARTCO WH13X10014 Washer Water Inlet Valve The XPARTCO WH13X10014 is an aftermarket replacement water inlet valve for GE washer/dryer combination units — a single cabinet that houses both wash and dry functions and shares one door, lid, and control system for both. This valve sits at the point where the hot and cold water supply lines connect, and it's the gatekeeper for every drop of water that enters the tub during the wash portion of a cycle. When the control calls for a fill, the valve's solenoid opens to admit water; once the correct level is reached, it closes again. Common causes of failure include mineral or sediment buildup inside the valve body that prevents it from sealing fully, and a burned-out internal solenoid coil. A failing valve on a combo unit produces the same core symptoms you'd see on a standalone washer: the wash side won't fill, fills too slowly, won't stop filling, or leaks after the cycle ends — but because a combo unit shares more components in a single cabinet than separate machines do, it's worth confirming the water issue is isolated to the valve and not connected to other combo-specific parts nearby, such as our WH12X955 lid switch listing, which serves this same GE combo platform. It directly replaces WH13X0084, WH13X10013, WH13X84, AP3203931, and 944040. Quick Answer The XPARTCO WH13X10014 Washer Water Inlet Valve fixes GE washer/dryer combo units that won't fill with water, fill slowly, won't stop filling, or leak after the cycle ends. For GE's combination washer/dryer platform (WSM2420/WSM2480 series). Replaces WH13X0084, WH13X10013, WH13X84, AP3203931, 944040. This valve is specific to GE's washer/dryer combo unit — not a standalone front-load or top-load washer valve. Common Problems This Part Fixes Washer/dryer combo won't fill with water at the start of the wash cycle Water fills much more slowly than normal Unit won't stop filling — water continues past the normal level Water leaking or dripping after the cycle has ended Cycle stalling at the fill step and never advancing to wash No hot water reaching the tub, or no cold water reaching the tub Unit not washing properly due to insufficient or incorrect-temperature water Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: WH13X10014, WH13X0084, WH13X10013, WH13X84, AP3203931, 944040, AH756629, EA756629, AGE844170, PD00066092, PS756629 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select GE washer/dryer combination units, including model numbers such as: GE WSM2420D0WW, WSM2420D1WW, WSM2420D2WW, WSM2420D3WW, WSM2420D4WW, WSM2420D5WW GE WSM2420D0CC, WSM2420D1CC, WSM2420D2CC GE WSM2420TAAWW, WSM2420TBAWW, WSM2420TCAWW, WSM2420TAAAA, WSM2420TAACC, WSM2420TBAAA GE WSM2420SAZAA, WSM2420SBZAA, WSM2420SBZWW, WSM2420SCZAA, WSM2420SCZWW, WSM2420SDZWW GE WSM2480D0WW, WSM2480D1WW, WSM2480D2WW, WSM2480D3WW GE WSM2480SAZAA, WSM2480SAZWW, WSM2480SBZAA, WSM2480SBZWW, WSM2480SEZAA, WSM2480TCAWW Note: This valve is built specifically for GE's washer/dryer combination units. It is not the same valve used on GE's standalone front-load washers (such as our WH13X10029 listing) and is not interchangeable with them. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement water inlet valve for GE washer/dryer combination units Resolves "won't fill," "fills slowly," "won't stop filling," and "leaking after cycle" symptoms caused by valve failure Solenoid-actuated design opens and closes precisely on the control's signal Direct drop-in replacement — matches the original mounting and hose connections Replaces WH13X0084, WH13X10013, WH13X84, AP3203931, and 944040 Compatible with GE washer/dryer combo units, including WSM2420 and WSM2480 series Aftermarket replacement built to OEM-equivalent quality standards Straightforward DIY repair using basic hand tools Product Specifications Part Number WH13X10014 OEM Part Number WH13X10014 Part Type Washer Water Inlet Valve Condition Aftermarket Replacement Application GE Washer/Dryer Combination Units Actuation Solenoid-operated Connections Hot and cold water supply inlets Quantity 1 valve Compatible Brand GE Installation Notes ⚠️ Shut Off Water Supply And Unplug Unit Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. On these combination units, the top of the cabinet often lifts off or opens as a single enclosure covering both the wash and dry sections, which also carries the lid switch wiring — note this connector's location before pulling the panel free. Disconnect the hot and cold water supply hoses from the back of the valve, keeping a towel handy for residual water. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector from the old valve, remove its mounting screws, and pull it free. Install the new WH13X10014 in the same position, reconnect the electrical connector fully, and secure the mounting screws. Reattach the hot and cold water supply hoses to the correct ports, tightening securely by hand plus a partial turn with pliers. Reinstall the cabinet enclosure, reconnecting the lid switch harness if it was disturbed, restore the water supply, and check every connection for leaks before restoring power. Run a short cycle and confirm the wash side fills at the normal rate with no leaking. Tools needed: Phillips screwdriver, pliers, towel, work gloves. Frequently Asked Questions Is this the same valve used on a standalone GE washer? No. This valve is built specifically for GE's washer/dryer combination units, which share a single cabinet and control system for both wash and dry functions. GE's standalone front-load washers use a different valve (such as our WH13X10029 listing), and the two are not interchangeable. Always confirm whether your appliance is a combo unit or a standalone washer before ordering. My unit won't stop filling. Is that this valve? Yes, this is one of the most common symptoms of a failing valve. A worn internal seal can fail to close fully, letting water continue flowing even after the correct fill level is reached. Since this could lead to overflow, it's worth shutting off the water supply at the wall if you notice this happening rather than waiting to address it. Only hot or only cold water isn't coming in. Do I need the whole valve? Usually yes. Most washer inlet valves use two separate solenoid coils in one housing — one for hot, one for cold — but they're not typically sold or serviced as separately replaceable coils. If just one side has stopped working while the other functions normally, that still points to a failure inside this valve assembly, and replacing the complete unit is the standard repair. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the solenoid design, connection type, and mounting configuration of the original WH13X10014 valve used in compatible GE washer/dryer combination units. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10238100 Refrigerator Water Valve - Compatible with Whirlpool, KitchenAid, Maytag, JennAir, Kenmore, IKEA Product Description Restore your refrigerator’s ice and water dispensing functionality with the replacement XPARTCO W10238100 Refrigerator Water Valve. This replacement part is designed for select Whirlpool, KitchenAid, Maytag, JennAir, Kenmore, and IKEA refrigerators, providing reliable water flow control for the ice maker and water dispenser. It resolves issues like no ice production, no water dispensing, poor water flow, or leaks, offering a cost-effective alternative to OEM parts. Note: Disconnect power and water supply before installation. Verify model compatibility for proper fit. Replaces part numbers: WPW10238100, W10238100, W10498992, IMV-8100, K-78199, PD00002616, EAP11750831, AP6017532, PS11750831. Compatibility: Compatible with models including but not limited to: Whirlpool: GSC25C4EYB02, GSS30C6EYY01, WSF26D4EXB00, WRF560SEHW00, WRF560SEHZ00, WRS526SIAH00 KitchenAid: KSF26C4XYB00, KSF26C6XYY05, KRSC503ESS01, KRFF300EBS01 Maytag: MSB26C6MDM00, MSB27C2XAB00, MFW2055DRE01 JennAir: JFI2089WES Kenmore: 10651764510, 10651789414, 10651133210 IKEA: ISC23CDEXB00 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand Compatibility: Fits select Whirlpool, KitchenAid, Maytag, JennAir, Kenmore, and IKEA refrigerators. 🔥 Specifications: Single solenoid water inlet valve with electrical connectors, 5/16" push-in to connect outlet, and 1/4" compression inlet. 💰 Cost-Effective Alternative: Matches OEM performance at a lower price. 🛠️ Easy Installation: Requires screwdriver, wrench, pliers; typically installed in 15–30 minutes. 🛡️ Effective Fixes: Resolves no ice, no water dispensing, poor water flow, or water leaks. Product Specification Part Number: XPARTCO W10238100 Component Type: Refrigerator water inlet valve Material: Plastic housing, metal fittings, electrical connectors Mounting: Secures to refrigerator frame with screws Operating Conditions: Suitable for refrigerator water systems; 20W, 120V coil Compliance: UL-listed components, Prop 65 warning for California Installation Notes: Safety First: Disconnect the refrigerator from power and water sources before installation. Follow the owner’s manual for guidance. Use plumber’s tape on threaded connections to prevent leaks. See Installation Guide.

Read more less

XPARTCO W10498976 Refrigerator Water Inlet Valve Replaces WPW10498976 The XPARTCO W10498976 is an aftermarket replacement refrigerator water inlet valve assembly compatible with select Whirlpool, Maytag, KitchenAid, Kenmore, and Ikea bottom-freezer and French door refrigerators in the WRB, WRF, MBF, GX5, GB9, GB2, and related series. The water inlet valve is a solenoid-operated valve mounted on the back of the refrigerator that controls the flow of water from the household supply line to the ice maker and, on models with a door dispenser, to the water dispenser. When the solenoid coil burns out or the valve seat becomes clogged with mineral deposits, the ice maker stops producing ice, the water dispenser stops working, water trickles weakly, or water leaks from the valve body. Rated 120V, 50/60Hz, 35W solenoid, this valve measures 3-1/2"L x 2-3/4"W x 3"H and includes the valve body and mounting bracket. It connects via 1/4" inlet fitting to the household supply line and uses push-in tube fittings on the outlet side. It directly replaces WPW10498976, W10420082, W10498974, K-78200, K-78186, 2684516, 2315508, IMV-576, AP6022334, EAP11755667, PD00024636, PS11755667, WP2315576, and WV8047. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO W10498976 Refrigerator Water Inlet Valve fixes Whirlpool-family bottom-freezer and French door refrigerators where the ice maker is not making ice, the water dispenser is not working or producing only a trickle, or water is leaking from the back of the refrigerator. 120V/50-60Hz/35W solenoid, 3-1/2"L x 2-3/4"W x 3"H, includes bracket. 1/4" inlet connection. Replaces WPW10498976, W10420082, W10498974, K-78200, 2684516, AP6022334, PS11755667. Compatible with Whirlpool WRB/WRF, Maytag MBF, KitchenAid, Kenmore, and Ikea. Common Problems This Part Fixes Ice maker not producing ice or producing very small cubes due to insufficient water supply Water dispenser not working — no water flows when the lever or button is pressed Water dispenser producing only a trickle — valve partially blocked or solenoid weakening Water leaking from behind the refrigerator near the water valve Ice maker fills but overflows — valve stuck open and not closing properly Humming sound near the back of the refrigerator when requesting ice or water — solenoid energized but valve not opening No water reaching the refrigerator despite supply line being connected and pressurized Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: WPW10498976, W10498976, W10420082, AWP50873, EAP11755667, PD00024636, AP6022334, PS11755667.  If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select bottom-freezer and French door refrigerators from the following brands and series: Whirlpool refrigerators — WRB322, WRB329, WRF535, WRF555, and related WRB/WRF series (French door and bottom-freezer models) Maytag refrigerators — MBF1958, MBF2258, and related MBF series KitchenAid refrigerators — select bottom-freezer and French door models Kenmore / Sears refrigerators — select Whirlpool-built models Ikea refrigerators — select models (Whirlpool-built) Other Whirlpool-platform models including GB9, GB2, GX5, GX2, ET1CH, ET8CH, IX5HH, ED22, and related series Note: Always verify your exact model number before ordering — water inlet valves are model-specific and not universal across all refrigerator configurations. Check that the supply line connection size (1/4") matches your existing supply line before purchasing. Key Features Solenoid-operated valve — opens on command from the refrigerator's control board to supply water to the ice maker and water dispenser Rated 120V, 50/60Hz, 35W — correct electrical specifications for compatible Whirlpool-family refrigerators Dimensions: 3-1/2"L x 2-3/4"W x 3"H — includes mounting bracket for direct installation 1/4" inlet connection — matches standard residential refrigerator supply line diameter Push-in outlet tube fittings — easy connection to existing water supply tubing inside the refrigerator Plastic and metal construction — durable and resistant to mineral buildup Replaces WPW10498976, W10420082, W10498974, K-78200, K-78186, 2684516, AP6022334, and over 10 additional cross-references Compatible with Whirlpool WRB/WRF series, Maytag MBF series, KitchenAid, Kenmore, and Ikea refrigerators Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number W10498976 OEM Part Number WPW10498976 Part Type Refrigerator Water Inlet Valve Assembly Condition Aftermarket Replacement Application Bottom-Freezer and French Door Refrigerators Voltage 120V AC Frequency 50/60 Hz Solenoid Wattage 35W Dimensions 3-1/2"L x 2-3/4"W x 3"H Inlet Connection 1/4 inch Color Brown / Blue / Yellow / Gray Material Plastic / Metal Includes Water valve body and mounting bracket Compatible Brands Whirlpool, Maytag, KitchenAid, Kenmore, Ikea Installation Notes ⚠️ Unplug Refrigerator and Shut Off Water Before Starting Unplug the refrigerator and shut off the household water supply valve before beginning. Place a towel and small container under the valve area to catch residual water. Pull the refrigerator away from the wall to access the back lower panel — remove the panel screws to expose the water inlet valve. Photograph the wiring harness connections and water tube connections before disconnecting. Turn off the water supply and disconnect the 1/4" supply line from the valve inlet — use an adjustable wrench, as some compression fittings may be stuck. Squeeze the plastic retaining clips on the outlet tube fittings and pull the internal water tubes free. Disconnect the wiring harness. Unscrew the mounting bracket and remove the old valve. Install the new W10498976 valve with its bracket, reconnect the internal water tubes (push until they click), reconnect the wire harness and supply line. Restore water supply and power. Run a water dispenser test and check for leaks. Tools needed: Phillips screwdriver, adjustable wrench, needle-nose pliers. Frequently Asked Questions What does the refrigerator water inlet valve do? The water inlet valve is an electrically controlled solenoid valve that opens on command from the refrigerator's control board to allow household water pressure to push water through to the ice maker fill tube or the water dispenser. When the ice maker calls for water or you press the dispenser lever, the board sends voltage to the solenoid coil, which opens the valve. When the demand is satisfied, the voltage stops, the spring closes the valve, and water flow stops. A failed solenoid coil — or a valve seat clogged with mineral deposits — prevents the valve from opening or closing correctly, causing no water, weak water, overflow, or dripping. What is the difference between W10498976 and WPW10498976? These are the same water inlet valve. WPW10498976 is the updated Whirlpool OEM part number that superseded the original W10498976. The W10420082 and W10498974 are also cross-references for this same valve from earlier production runs. This aftermarket replacement is compatible with all of these numbers. How do I know if the water inlet valve has failed vs. something else? First confirm the household water supply valve behind the refrigerator is fully open and the supply line is not kinked. Then check the water filter — a clogged filter is one of the most common causes of weak or no water flow and is mistaken for a valve failure. If both supply pressure and the filter are good, test the valve's solenoid coil with a multimeter — a working coil reads 200–500 ohms of resistance; an open circuit confirms failure. If the solenoid tests good but the valve still does not open when the control board sends voltage, the valve seat may be physically clogged with mineral deposits and the valve needs to be replaced. My ice maker is not working but my water dispenser is fine — is it the valve? Possibly — but if the water dispenser works normally, the main valve solenoid is likely functioning. On some refrigerator configurations, the ice maker and the dispenser are controlled by separate solenoid ports on the valve assembly. If only the ice maker port has failed, the dispenser can continue working while ice production stops. Test the ice maker solenoid coil separately. However, a more common cause of ice maker failure with a working dispenser is the ice maker module, freezer temperature, or ice maker shut-off arm — rule out those causes before replacing the valve. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from plastic and metal to match the electrical specifications and dimensions of the original WPW10498976 water inlet valve assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DD62-00084A Dishwasher Water Valve – Compatible with Samsung Dishwashers Product Description Restore proper water flow and reliable cleaning performance with the XPARTCO DD62-00084A Dishwasher Water Valve. This Dishwasher Water Valve is an essential component for maintaining the optimal performance of your dishwasher. This replacement part ensures precise water flow control, allowing your dishwasher to operate efficiently and effectively. A faulty water valve can cause no water entering the dishwasher, slow filling, or poor cleaning performance. Replacing it with this dependable XPARTCO valve helps restore consistent water flow and efficient operation. XPARTCO provides cost-effective aftermarket appliance parts engineered to match original fit and function. Replaces Part Numbers DD62-00084A, 2692215, ASM36078, EAP4222448, PD00002158, 737534554937, OEM15534663, AP5178218, PS4222448 Compatibility This replacement dishwasher water inlet valve fits select Samsung dishwashers. Common compatible models include (but are not limited to): Samsung DW80F600UTS Samsung DW80J3020US Always verify your dishwasher’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and water flow performance 💧 Accurate Water Fill Control – Ensures proper water levels for effective cleaning ⚙️ Fixes Common Issues – Resolves no-fill or slow-fill problems 💪 Durable Solenoid Valve – Designed for reliable long-term use 💰 Cost-Effective Repair – Affordable alternative to OEM valves ⚠️ Symptoms If your dishwasher is experiencing any of the following issues, this part may need replacement: ❌ Dishwasher not filling with water 💧 Slow or weak water flow ⚠️ Poor cleaning performance due to low water level 🔄 Cycle not starting properly 🚫 No water entering during wash cycle Replacing this water valve can restore proper dishwasher operation and cleaning efficiency. 📐 Product Specification Part Number: XPDD62-00084A Component Type: Dishwasher Water Inlet Valve Voltage: 120V AC Application: Dishwasher water supply system Mounting: Screw-mounted with hose connection Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, adjustable wrench ⚠️ Safety First: Disconnect power and shut off the water supply before servicing the dishwasher. Basic Steps: Turn off power and water supply. Remove the lower access panel. Disconnect water supply line and electrical connector. Remove mounting screws and remove the old valve. Install the new XPARTCO DD62-00084A valve. Reconnect water line and wiring. Restore power and water, then test for leaks and proper filling. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore reliable dishwasher performance — Add to Cart Now for a dependable repair!

Read more less

W10918546CM Gas Oven Igniter Replaces Part Numbers: W10918546, W10140611, 98005652, W10918546VP, WPW10140611, AP6037202, PS11770066. 3.4 - 3.6 Amp, 1.5" block, 3.75" cage, 10" leads w/male pins. Bake igniter for specific single burner Whirlpool range models. Description: This Oven Igniter is a replacement part for select Maytag, Kenmore, Whirlpool gas oven models, responsible for igniting the gas burner that heats the oven. It works by drawing electrical current through the igniter filament, heating it to a high temperature until it glows and ignites the gas to start the cooking process. This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

022112-000 Genuine OEM NIPPLE 1/2 NPT Models that Have Used This Part DGVU2004B DGVU260-5B   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WB02X4221CM Gas Range Oven Igniter  Gas Oven Igniter  3.2 - 3.6 Amp igniter with 5.5" overall length. Fits Specific GE Gas Range, Oven Models. Replaces Part Numbers: WB2X4306, WB02X4221, WB02X4306, WB02X4752, WB2X4221, WB2X4752, AH242243, EA242243, AP2011155, PS242243.  Description: This Flat Style Oven Igniter Kit is a replacement part for specific GE gas oven models. It is designed to ignite the gas in the oven burner, facilitating the start of the heating process. This igniter is crucial for ensuring your oven heats up quickly and efficiently, providing the necessary flame for cooking and baking.  This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

W10865826 Refrigerator Water Valve - Compatible with Whirlpool, KitchenAid, Maytag, JennAir, Kenmore Product Description Restore your refrigerator’s ice and water dispensing functionality with the replacement W10865826 Refrigerator Water Valve. This replacement part is designed for select Whirlpool, KitchenAid, Maytag, JennAir, and Kenmore refrigerators, ensuring precise water flow control for the ice maker or water dispenser. It resolves issues like no ice production, no water dispensing, or leaks, offering reliable performance and durability. Note: Disconnect power and water supply before installation. Verify model compatibility for proper fit. Replaces part numbers: W10865826, W10394076, WPW10394076, 4459687, W10726788, W10833705, W10872966, PD00041363, EAP11738056, AP6026312, PS11738056.  Compatibility: Compatible with models including but not limited to: Whirlpool: WRF736SDAM, WRF767SDHZ, WRX986SIHZ, KRFF507HPS KitchenAid: KRMF706ESS Maytag: MFI2570FEZ JennAir: JFX2897DRM Kenmore: 10651753710 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand Compatibility: Fits select Whirlpool, KitchenAid, Maytag, JennAir, and Kenmore refrigerators. 🔥 Specifications: Water inlet valve with solenoid, electrical connectors, and water line fittings. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires screwdriver, wrench, pliers; typically installed in 15–30 minutes. 🛡️ Effective Fixes: Resolves no ice, no water dispensing, or water leaks. Product Specification Part Number: W10865826 Component Type: Refrigerator water inlet valve Material: Plastic housing, metal fittings, electrical connectors Mounting: Secures to refrigerator frame with screws Operating Conditions: Suitable for refrigerator water systems Compliance: UL-listed components, Prop 65 warning for California Installation Notes: Safety First: Disconnect the refrigerator from power and water sources before installation. Follow the owner’s manual for guidance. Use plumber’s tape on threaded connections to prevent leaks. Shop for high-quality replacement appliance parts with a 30-day return policy. Fix your refrigerator today! Add to cart now for a reliable solution!

Read more less

WD24X10018 Dishwasher Genuine Piston & Nut Assembly Replaces Part Numbers: WD24X10018, 821081, WD22X0133, WD22X133, WD24X0199, WD24X0220, WD24X199, WD24X220, AH260690, EA260690, AP2617344, PS260690. Description: This Piston & Nut Assembly is a Genuine parts for specific GE dishwasher models. It plays a critical role in the dishwasher’s water management system, helping to control water flow and ensuring proper drainage during the wash cycle. You should replace this piston & nut assembly if it becomes worn out or damaged. Common causes of a bad piston & nut assembly can include mineral buildup from hard water, general wear and tear from regular use, or physical damage due to debris or foreign objects in the dishwasher.

Read more less

5303281153 Dryer Rear Drum Bearing Kit - Compatible with Frigidaire, Electrolux, Kenmore, Gibson Dryers Product Description Keep your dryer running smoothly with the Replacement 5303281153 Dryer Rear Drum Bearing Kit. This Genuine OEM replacement kit, designed for select Frigidaire, Electrolux, Kenmore, Gibson, and other brand dryers, includes a bearing cup (131825900), ball shaft (131777700), ball bearing (5303281019), ball bearing retainer (5303281020), high-temperature lubricant, and mounting screws to support the drum’s rear for quiet, efficient rotation. It fixes issues like loud squeaking, grinding, or thumping noises, drum not tumbling, or marks on clothes due to misalignment. Note: Requires drum removal to access the bearing. Inspect the drum, belt, and front glides for wear. Clean lint from the drum and cabinet to prevent overheating. Use self-tapping screws provided to thread the unthreaded metal plate. Replaces part numbers: 5303281153, AP2142648, 1851, 3281153, 5304459240, 85-852, AH459829, DE724, EA459829, PS459829, Q000142850, Q142850, WQ142850, 08015113, 08015324, 131378400, 131777700, 137088600, 137088620, 137088630, 3281019, 3281020, 5303281009, 5303286875, 8015113, 8015324, 902088, Q000022224, Q000500537, WQ22224, WQ500537 Compatibility: Compatible with models including but not limited to: Frigidaire: FDE436RBS2, FDE546RBS1, FDE747RES0, FDES69RHW1, FEX831CS0, FEQ332ES0, FEQ1442ES0, LEQ6000ES0, LEQ2152EE0, GLEQ2152ES0, MDG336MBW2, MDG436RBD0 Kenmore: 417.49012890, 417.59012890, 417.94802301, 417.97812700 Electrolux: AEQ6000ES2, AGQ6000ES2 Gibson: GDE436RBW1, GDE546RBS1 Westinghouse: WDE846RBW0 Verify your model number or contact Parts-O-Matic support for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Frigidaire, Electrolux, Kenmore, Gibson, Westinghouse, Kelvinator, Tappan, Crosley, and Universal/Multiflex dryer models. 🔥 Specifications: Includes 1 white plastic bearing cup (131825900, ~2" diameter x 1" depth), 1 ball shaft (131777700), 1 ball bearing (5303281019), 1 ball bearing retainer (5303281020), high-temperature lubricant tube, 3 self-tapping screws, 3 washers, 2 bracket screws, bearing assembly ~1-15/16"L x 1"W x 1-3/8"H with mounting holes 1-1/2" apart (center to center). 💰 Genuine OEM Part. 🛠️ Easy Installation: Requires a putty knife, Phillips screwdriver, flat-blade screwdriver, work gloves, optional second person; typically installed in 45–90 minutes. 🛡️ Reliable Fixes: Resolves loud noises, drum not tumbling, or marks on clothes. Safety First: Unplug the dryer from the power source and, for gas dryers, shut off the gas valve before installation. Shop Parts-O-Matic for Genuine OEM appliance parts with a 30-day return policy. Get your dryer back to smooth, quiet performance today! Add to cart now for a budget-friendly fix!

Read more less

ERP 12544002 Refrigerator Water Valve Replaces Part Numbers: WP12544002, 12544002, 8171096, 915068, AP6005463, PS11738512. Primary Water Inlet Valve Description: This Primary Water Inlet Valve is a replacement part for select Kenmore, Maytag, Whirlpool refrigerator models. This valve controls the flow of water into the refrigerator's ice maker and water dispenser. Common causes of a bad primary water inlet valve can include mineral deposits or debris clogging the valve, electrical issues such as faulty solenoids, and general wear and tear from frequent use.     This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

W10158389 Dishwasher Genuine OEM Water Inlet Valve Description: This Dishwasher fill valve assembly is an OEM replacement part for specific Whirlpool brand dishwasher models. It is responsible for controlling the water flow into the dishwasher during the wash or rinse cycles. This part is typically located at the back or bottom of the appliance, where the water supply hoses connect. The fill valve assembly ensures that the appliance receives the correct amount of water while regulating water pressure and preventing overflow. Replaces Part Number: WPW10158389, W10158389, 8558986, 8558987, 8558988, 8563405, 8563406, 8563407, ERW10158387, AP6015932, PS11749213, W10158387, B01M1HL30X, WPW10158389VP.        California Residents only WARNING: California’s Proposition 65 

Read more less