Search results for "contactor"

XPARTCO WR17X11653 Refrigerator Dispenser Ice Door Flapper The XPARTCO WR17X11653 is an aftermarket replacement ice door flapper, also sold as the dispenser door assembly, ice chute door or door recess assembly, for GE, Hotpoint and Kenmore side-by-side refrigerators, replacing GE part WR17X11653. It sits in the ice chute opening, seals the freezer against warm room air, and opens when the dispenser lever is pressed so ice can reach your glass. If the door is cracked, warped, or its gasket no longer seals, warm air gets into the chute and the dispenser suffers. Check your model number before ordering, as the kit may include more than one piece. Quick Answer The XPARTCO WR17X11653 Ice Door Flapper replaces the ice chute door on a compatible GE, Hotpoint or Kenmore refrigerator when it is cracked, warped, or no longer seals. Classic symptoms: door sweating, frost buildup at the chute, or ice not dispensing. Common Problems This Part Fixes Ice dispenser door sweating Frost buildup around the ice chute Ice not dispensing Cracked, warped or damaged ice door Worn rubber gasket leaking air into the freezer Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This ice door flapper directly replaces the following part numbers: WR17X11653, WR17X3093, WR17X3492, AGE28222, AH964304, AP3672582, EA964304, EAP964304, PD00001157, PS964304 If your old part shows a different number, contact our support team and we'll check whether it matches. Compatibility This ice door flapper is listed for GE, Hotpoint and Kenmore side-by-side refrigerators, including these examples: GE TPH21PRSABB, TPH21PBSAWW, TFX20JRSBAD GE DSE26JSEBCSS, DSF25KGTABG, DSF26DHWABB, CSK28DRBBAA Kenmore 3639544313, 3639537713, 3639542623 Note: The models above are a small sample. One retailer lists this part for over 1,000 models. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Aftermarket replacement for the GE WR17X11653 ice door flapper Seals the ice chute opening against warm room air Opens when the dispenser lever is pressed to release ice Replaces a cracked, warped or leaking ice door Product Specifications Part Number XPWR17X11653 OEM Part Number WR17X11653 Part Type Refrigerator Dispenser Ice Door Flapper Condition Aftermarket Replacement Application Select GE, Hotpoint and Kenmore Side-by-Side Refrigerators Installation Notes ⚠️ Unplug Power Before Installing Unplug the refrigerator and move perishable food to a cooler before you begin. Wear work gloves. A Phillips screwdriver and a small flat-blade screwdriver are typically needed. No installation instructions are included with the part, so keep your model's parts diagram handy and note how the old door and any springs or pieces come apart before removing them. Install the new door the same way, then restore power and test the dispenser. Frequently Asked Questions What does the ice door flapper do? It seals the ice chute opening to keep warm room air out of the freezer, and it opens when you press the dispenser lever so ice can drop into your glass. How do I know if my ice door needs replacing? Look for a cracked or warped door, a damaged rubber gasket, door sweating, or frost buildup around the chute. Ice that won't dispense can also point to the door. Is this an OEM or aftermarket part? This is an aftermarket replacement from XPARTCO, made to replace GE part WR17X11653. If you specifically need a genuine GE part, contact our support team. Will this fit my refrigerator? It is listed for a large number of GE, Hotpoint and Kenmore side-by-side models, but the list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 279393 Dryer Terminal Block Screw Kit The XPARTCO 279393 is an aftermarket replacement terminal block screw kit compatible with a wide range of Whirlpool-family electric dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef, and Norge. The terminal block screws secure the dryer power cord wires to the terminal block — the connection point where 240V power enters the dryer. Loose, corroded, or damaged screws at this connection can cause intermittent power loss, blown fuses, tripped breakers, or dangerous arcing. This kit includes 3 chrome-plated screws and 3 nuts — everything needed to restore a secure, conductive connection at the terminal block. The chrome plating improves electrical conductivity and corrosion resistance. Screws measure 7/16" L x 7/16" W x 11/16" H; nuts measure 1/2" L x 1/2" W x 1/8" H. Installs in under 15 minutes with basic hand tools. Quick Answer The XPARTCO 279393 Terminal Block Screw Kit fixes electric dryers with intermittent power, blown fuses, tripped circuit breakers, hot terminals, or visible arcing and scorching at the power cord connection. Includes 3 chrome-plated screws and 3 nuts. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, and more. Common Problems This Part Fixes Dryer has intermittent power or will not start at all Internal fuses repeatedly blowing without another clear cause Circuit breaker for the dryer repeatedly tripping Terminal block area is hot to the touch during or after operation Visible arcing, sparks, scorch marks, or smoke around the terminal block cover Heating element or motor works intermittently but not consistently Dryer power cord connection is loose, corroded, or visibly damaged Replaces Part Numbers This terminal block screw kit directly replaces the following OEM and cross-reference part numbers: 279393, 279393D, 279393VP, 3184, EAP334188, AWP39844, PD00003883, AH334188, EA334188, AP3020386, PS334188 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This terminal block screw kit is compatible with select electric dryers from the following brands: Whirlpool electric dryers Kenmore / Sears electric dryers (Whirlpool-built models) Maytag electric dryers KitchenAid electric dryers Amana electric dryers Roper electric dryers Admiral electric dryers Estate electric dryers Crosley electric dryers Inglis electric dryers Magic Chef, Norge, and Jenn-Air electric dryers Note: This kit is for electric dryers only. Gas dryers do not use a terminal block for power cord connections. Key Features Secures the dryer power cord wires to the terminal block for a safe, reliable 240V connection Kit includes 3 screws and 3 nuts — one complete set for all three terminal positions Chrome-plated metal construction — improves electrical conductivity and resists corrosion Screw dimensions: 7/16" L x 7/16" W x 11/16" H; Nut dimensions: 1/2" L x 1/2" W x 1/8" H Direct replacement for OEM part numbers 279393, 279393D, and 279393VP — no modification required Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, and more Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in under 15 minutes with basic hand tools Product Specifications Part Number 279393 Part Type Terminal Block Screw and Nut Kit Condition Aftermarket Replacement Application Electric Dryers (240V terminal block) Kit Contents 3 chrome-plated screws and 3 nuts Screw Dimensions 7/16" L x 7/16" W x 11/16" H Nut Dimensions 1/2" L x 1/2" W x 1/8" H Material Chrome-plated metal Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef, Norge, Jenn-Air Dryer Type Electric dryers only ⚠️ Electrical Safety Warning This kit connects the power cord to the dryer's terminal block — a high-voltage connection carrying 240V. Always unplug the dryer and shut off the circuit breaker before beginning installation. Loose or improperly tightened terminal screws can cause arcing, overheating, blown fuses, or fire. If you are not comfortable working with high-voltage electrical connections, have this part installed by a qualified appliance technician. Installation Notes ⚠️ Unplug and Switch Off Breaker Before Starting Unplug the dryer from the wall outlet and turn off the circuit breaker for the dryer before beginning any work on the terminal block. Locate the terminal block cover plate on the back of the dryer and remove it by unscrewing the retaining screw. Use needle-nose pliers to carefully disconnect the power cord wires from the terminal block. Remove the old screws and nuts using a Phillips or flat-head screwdriver. Install the new 279393 screws and nuts into the terminal block. Reconnect the power cord wires to the correct terminals — refer to the label inside the terminal block cover or your dryer's wiring diagram to confirm wire positions. Tighten all screws firmly but do not overtighten. Replace the terminal block cover plate. Restore power and run a test cycle to verify correct operation. Tip: While the cover is off, inspect the terminal block itself (part 694431) for burn marks or damage. If the block is damaged, replace it before reinstalling. Tools needed: Phillips screwdriver, flat-head screwdriver, needle-nose pliers. Frequently Asked Questions What is the terminal block screw kit used for? The terminal block screw kit secures the three wires of the dryer's power cord (two hots and a neutral, or two hots and a ground depending on cord type) to the terminal block at the back of the dryer. This is the point where 240V power enters the machine. The screws must be firmly tightened to maintain a safe, low-resistance electrical connection. If they loosen or corrode over time, resistance increases at the connection — causing heat, arcing, blown fuses, or power loss. Can I also use this kit when installing a new dryer power cord? Yes — this kit is commonly needed when installing a new 3-wire or 4-wire dryer power cord. When switching from a 3-wire to 4-wire cord (or vice versa), the terminal block screws and nuts often need to be loosened and retightened, and replacing them with a fresh set ensures a secure, corrosion-free connection from the start. Should I also inspect the terminal block itself? Yes. While the terminal block cover is off, inspect the block itself (part 694431) for burn marks, melted plastic, or damaged terminals. If the block shows any of these signs, it should be replaced before reinstalling — new screws alone cannot fix a damaged terminal block. Contact our support team to find the correct terminal block for your model. Does this kit work for gas dryers? No. Gas dryers use a standard 120V three-prong household plug and do not have a terminal block for power cord connections. The 279393 kit is for electric dryers only, which use a 240V outlet and require a hard-wired terminal block connection for the power cord. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is made from chrome-plated metal to match the dimensions and electrical performance of the original 279393 screw kit. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

ERP 3406108 Dryer Door Switch  Replaces Part Numbers: WP3406108, 3406108, PS11741702, AP6008562  Description: This Door Switch is a replacement part for select Whirlpool dryer models. It is responsible for detecting whether the dryer door is open or closed. When the door is closed, the switch allows the dryer to operate. Conversely, if the door is open, the switch interrupts the electrical circuit to prevent the dryer from running, ensuring safety during use. Fits Models:   LTE5243DQ1 , LTE5243DQ2 , LTE5243DQ3 , LTE5243DQ4 , LTE5243DQ5 , LTE5243DQ6 , LTE5243DQ7 , LTE5243DQ8 , LTE5243DQ9 , LTE5243DQA , LTE5243DQB , LTE5243DT2 , LTE5243DT3 , LTE5243DT4 , LTE5243DT5 , LTE5243DT6 , LTE5243DT7 , LTE5243DZ1 , LTE5243DZ2 , LTG5243DQ1 , LTG5243DQ2 , LTG5243DQ3 , LTG5243DQ4 , LTG5243DQ5 , LTG5243DQ6 , LTG5243DQ7 , LTG5243DQ8 , LTG5243DQ9 , LTG5243DQA , LTG5243DQB , LTG5243DQC , LTG5243DT2 , LTG5243DT3 , LTG5243DT4 , LTG5243DT5 , LTG5243DT6 , LTG5243DT7 , LTG5243DT8 , LTG5243DZ1 , LTG5243DZ2 , WET4024EW0 , YLTE5243DQ2 , YLTE5243DQ3 , YLTE5243DQ4 , YLTE5243DQ5 , YLTE5243DQ6 , YLTE5243DQ7 , YLTE5243DQ8 , YLTE5243DQ9 , YLTE5243DQA , YLTE5243DQB , YWET4024EW0. This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less

W10503278 Refrigerator Control Board Refrigerator electronic (JAZZ) control board. Be aware the board will need to programmed after installation to work properly Replaces Part Numbers: WPW10503278, 12784415, W10503278, 12002339, 12002445, 12002449, 12002508, 12002509, 12002567, 12002706, 12784415V, 12868502, 12868510, 12868513, 2684578, 67003867, 67004453, 67004496, 67004907, 67005043, 67005280, 67005281, 67006034, 67006209, 67006214, 67006216, 67006226, 67006712, 67006740, 8208187, AP6022400, PS11755733, W10165748. Description: This Electronic Control Board is a replacement part for Specific Maytag, Whirlpool refrigerator models. This Electronic (JAZZ) Control Board manages various functions of your refrigerator, ensuring proper temperature control and operation. This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

EXP572 Dryer Door Catch – Aftermarket Replacement for Whirlpool, Kenmore, Maytag, GE, Hotpoint Product Overview This Door Catch is a replacement part for specific GE, Hotpoint dryer models. It includes the door catch. This part ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently. Common causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly Replaces Part Numbers WE1M1011, PS3502777, AP5324728, WE01M0197, WE01X0889, WE01X0903, WE01X1032, WE1M187, WE1M197, WE1M536, WE1X1032, WE1X889, WE1X903. It provides a reliable fit and function similar to OEM components. Fixes the Following Issues Dryer door won’t stay closed Dryer doesn’t start Door pops open mid-cycle Worn or damaged door catch Compatible Brands Compatible with dryers made by Whirlpool, Kenmore (Whirlpool-built), Maytag, Amana, Roper, Estate, GE and Crosley. Suitable for many front-load and top-load residential models. Why Buy from Parts-O-Matic High-quality, durable replacement part Always Fast and Free U.S. shipping Easy to install – no special tools required Trusted by appliance repair professionals and DIYers

Read more less

XP4P-ROLP-120P15 Refrigerator Starter Relay & Overload Protector Refrigerator Compressor Overload Protector PTC Starter Relay Replaces 1.03.01.01.324J, ZHB35-120P15 BEU: This PTC starter relay is specifically designed for refrigerator compressors. It serves as an overload protector and ensures the proper functioning of your refrigerator compressor. The model ZHB35-120P15 BEU guarantees compatibility with your appliance. Description: Easy to install and replace your old part: This PTC starter relay for refrigerator compressor overload protector is designed for easy installation and replacement of your old part. It saves you time and effort in the installation process. Check well before shipment: Each unit of this refrigerator compressor overload protector PTC starter relay is carefully checked before shipment to  for ensure its quality and functionality.  This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO WB24X10146 Microwave Door Switch The XPARTCO WB24X10146 is an aftermarket replacement micro switch (also called a door interlock switch) compatible with a wide range of GE, Hotpoint, RCA, Kenmore, and Sears over-the-range and countertop microwaves. This is a "stand on" style normally-open (NO) interlock switch, identified by the internal designation KW3A-NO, that mounts near the door latch and only closes its circuit when the door is fully shut and latched. The control board reads this switch as part of a multi-switch safety interlock chain that confirms the door is secure before allowing the magnetron to energize. When this switch fails, the microwave commonly won't start at all, trips a door-related error code, or in rare cases can allow the unit to run with the door not fully secured — which is a safety-relevant fault, not just a convenience one. It directly replaces WB24X10146, WB24X28941, MW-7100-33, AGE22794, AH1019163, AP3866977, 1166990, EA1019163, EAP1019163, PD00039881, PS1019163. Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO WB24X10146 Microwave Door Switch fixes GE, Hotpoint, RCA, and Kenmore/Sears microwaves that won't start, display a door-related error code, or have a door that doesn't reliably confirm as closed. Normally-open (NO) "stand on" interlock switch, rated 250VAC / 16A, with 0.187" (4.7mm) quick-connect terminals. Replaces WB24X10146, WB24X28941, MW-7100-33, AGE22794, AH1019163, AP3866977, 1166990, EA1019163, EAP1019163, PD00039881, PS1019163. Classic symptom: turntable light and display work, but pressing Start does nothing. Common Problems This Part Fixes Microwave won't start when Start is pressed, even though the display and light work Door-related error code or fault light on the display Microwave randomly shuts off mid-cycle Door feels like it isn't latching or registering as closed Clicking sound from the door area with no response from the microwave Intermittent operation that seems tied to how hard the door is closed ⚠ Safety-Relevant Component Door interlock switches are safety components that prevent the magnetron from energizing unless the door is fully closed and latched. Never bypass, jumper, or defeat a microwave door switch to "get it working" — doing so can allow microwave energy to leak while the door is open, which is a genuine radiation safety hazard. Always disconnect power before servicing, and replace all interlock switches in the chain if more than one shows signs of wear. Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This microwave door switch directly replaces the following OEM and cross-reference part numbers: WB24X10146, WB24X28941, MW-7100-33, AGE22794, AH1019163, AP3866977, 1166990, EA1019163, EAP1019163, PD00039881, PS1019163 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is compatible with a wide range of GE-built microwaves across the following brands: GE over-the-range and countertop microwaves (JVM, PVM, and CEB series, including JEM3072DH1BB, JEM3072SH1SS, JNM3161DF2BB, and CCWK15C1W1DS/SS) Hotpoint microwaves (GE-built models) RCA microwaves (GE-built models) Kenmore and Sears microwaves (select GE-built models) Note: Do not confuse this with the similarly styled EXP499/EXP497 microwave door switches, which also use 4.7mm terminals but are not the same switch. WB24X10146 is a "stand on" style switch specific to GE's own interlock design — always match by part number, not terminal size alone. Always verify your appliance model number before ordering. Key Features Normally-open (NO) "stand on" door interlock switch, internal designation KW3A-NO Resolves "won't start," "door error code," and "shuts off mid-cycle" symptoms caused by interlock switch failure Rated 250VAC / 16A for reliable switching under microwave load 0.187" (4.7mm) quick-connect terminals for a secure wire connection Direct-fit mounting to match the original interlock bracket Replaces WB24X10146, WB24X28941, MW-7100-33, AGE22794, AH1019163, AP3866977, 1166990, EA1019163, EAP1019163, PD00039881, PS1019163 Compatible with GE, Hotpoint, RCA, Kenmore, and Sears microwaves across dozens of models Aftermarket replacement built to OEM-equivalent quality and safety standards Product Specifications Part Number XPWB24X10146 OEM Part Number WB24X10146 Part Type Microwave Door Interlock Switch ("Stand On" / KW3A-NO) Condition Aftermarket Replacement Switch Type Normally Open (NO) Voltage Rating 250VAC Current Rating 16A Terminal Width 0.187" (4.7mm) Compatible Brands GE, Hotpoint, RCA, Kenmore, Sears Installation Notes ⚠️ Unplug Microwave Before Starting Disconnect power at the outlet, and for built-in/over-the-range units also switch off the dedicated circuit breaker — microwaves store high voltage in the capacitor even after unplugging. Remove the outer cabinet or control panel cover to access the door switch assembly near the latch mechanism. Photograph the wiring before disconnecting, since GE microwaves typically use two or three interlock switches wired in sequence and mixing up the connections can leave the unit unsafe to operate. Disconnect the quick-connect terminals from the old switch, noting which wire goes to which terminal. Remove the mounting screw(s) holding the switch to its bracket and remove the old switch. Install the new WB24X10146 in the same position and secure it with the mounting screw(s). Reconnect the terminals exactly as photographed. Reassemble the cabinet or panel, restore power, and test that the door registers correctly and the microwave starts normally. Tools needed: Phillips screwdriver, nut driver (for cabinet screws). Frequently Asked Questions My microwave's display and turntable light work, but it won't start — is this the part? This is a classic symptom of a failed door interlock switch. The control board needs a confirmed "door closed and latched" signal from all switches in the interlock chain before it will energize the magnetron. If that signal is missing from even one switch, most GE microwaves will power up normally but refuse to start a cook cycle. Confirm with a multimeter continuity test on the suspect switch before ordering, since GE microwaves usually use more than one interlock switch. Is this the same as the EXP499 or EXP497 microwave door switch? No — while all three use similar 4.7mm terminals, they are different switches used in different microwave platforms and are not interchangeable. WB24X10146 is GE's own "stand on" KW3A-NO design. Always match by part number rather than terminal size or general appearance. Is it safe to keep using the microwave if I suspect this switch is bad? We'd recommend not continuing to use it until it's repaired. Door interlock switches exist specifically to prevent microwave energy from leaking out while the door is open or not fully latched. If a switch is failing intermittently, the microwave may seem to work sometimes, but that's not a reason to keep using it — replace the switch before further use, and never attempt to bypass or jumper an interlock switch. How many interlock switches does my GE microwave have, and do I need to replace them all? Most GE microwaves use two or three interlock switches wired in sequence (often a primary switch, a secondary/monitor switch, and sometimes a door sensing switch). You typically only need to replace the specific switch that's testing bad, but if one has failed from age or wear, the others are often not far behind — some technicians replace the full set at once to avoid a repeat repair call. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO EXP480 Microwave Door Switch (NC - NO) Normally Closed / Open The XPARTCO EXP480 is a universal replacement door interlock switch for microwave ovens and microwave/oven combination units. This is a critical safety component: microwave door interlock switches exist specifically to cut power to the magnetron the instant the door opens, preventing any possibility of microwave radiation escaping the cavity while the door isn't fully closed and latched. This switch combines both a normally closed (NC) and normally open (NO) contact set in a single body, matching the dual-contact design used across a wide range of microwave door latch mechanisms. Rated 16A maximum current, 250VAC maximum voltage, with an IP40 protection rating. Over time, these switch contacts can wear, pit, or fuse together from repeated cycling and the electrical load they carry every time the door opens and closes. A failing interlock switch typically shows up as a microwave that won't start at all, a display that works but the unit won't heat, or in less common but more serious cases, a switch that has fused shut and continues carrying current even when it shouldn't. It directly replaces 28QBP0496, W10211972, 4375346, W10330566, WPW10330566, 1472224, 4393442, 4393498, 4393570, 4393697, 4393881, 461967848881, 8206345, W10131248, W10217468, AH2338920, EA2338920, AP4357880, PS2338920, KW3A-16Z0-A200-76, W10727360, W10269457, 3379124, AP5950105, and PS10057151. Quick Answer The XPARTCO EXP480 Microwave Door Switch (NC - NO) fixes microwave ovens and microwave/oven combos that won't start, won't heat, or have a door latch mechanism that isn't reliably cutting power when the door opens. 16A, 250VAC, combined NC/NO contact design. Replaces 28QBP0496, W10211972, 4375346, W10330566, WPW10330566, 1472224, 4393442, 4393498, 4393570, 4393697, 4393881, 461967848881, 8206345, W10131248, W10217468, AH2338920, EA2338920, AP4357880, PS2338920, KW3A-16Z0-A200-76, W10727360, W10269457, 3379124, AP5950105, PS10057151. Never operate a microwave with a bypassed, disconnected, or suspected-faulty door interlock switch — these switches exist to prevent radiation exposure and must always be replaced with a properly rated part, never removed or defeated. Common Problems This Part Fixes Microwave won't start at all, even though the display and buttons respond normally Microwave display and timer work, but the unit won't heat Microwave stops working intermittently, especially around the door latch Clicking or buzzing sound from the door area without the microwave starting Breaker tripping when the door is opened, indicating a switch contact that has fused shut Door that doesn't feel like it's latching securely Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This microwave door switch directly replaces the following OEM and cross-reference part numbers: 28QBP0496, W10211972, 4375346, W10330566, WPW10330566, 1472224, 4393442, 4393498, 4393570, 4393697, 4393881, 461967848881, 8206345, W10131248, W10217468, AH2338920, EA2338920, AP4357880, PS2338920, W10727360, W10269457, 3379124, AP5950105, PS10057151 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is a universal replacement compatible with convection microwave ovens, grill microwave ovens, microwave/oven combination units, and solo microwave ovens across many brands, wherever the original switch matches this NC/NO contact configuration and electrical rating. Note: Microwave door interlock systems typically use two or three separate switches working together (primary interlock, monitor/secondary switch, and sometimes a third safety switch), and not all of them share this same NC/NO configuration. Confirm which specific switch position has failed on your microwave, and match the contact configuration and electrical rating exactly — never substitute a switch with a different configuration. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which switch your microwave needs. Key Features Universal replacement microwave door interlock switch — combined NC (normally closed) and NO (normally open) contact design Resolves "won't start," "won't heat," and "intermittent operation near the door latch" symptoms caused by switch failure Rated 16A, 250VAC maximum IP40 protection rating Safety approved: CCC, CE, UL, VDE Suitable for convection, grill, combination, and solo microwave ovens Direct drop-in replacement matching the original mounting and terminal configuration Replaces a wide range of OEM part numbers across Whirlpool, GE, and related platforms — see full list above Built to OEM-equivalent quality standards Product Specifications Part Number EXP480 Part Type Microwave Door Interlock Switch (NC/NO Combination) Condition New — Universal Replacement Part Contact Configuration Normally Closed (NC) + Normally Open (NO) Max. Current 16A Max. Voltage 250VAC Operating Temperature -25°C to +85°C Protection Degree IP40 Contact Form SPDT Terminal Size 6.3mm (approx. 1/4") Operating Force 25g (0.245N) – 400g (3.92N) Material Plastic Color Gray Safety Approvals CCC, CE, UL, VDE Application Convection, Grill, Combination, and Solo Microwave Ovens Quantity 1 door interlock switch Installation Notes ⚠️ Danger — Never Bypass A Door Interlock Switch Unplug the microwave before beginning any work, and if it's a built-in or over-the-range unit, shut off power at the breaker as well. Microwave ovens also contain a high-voltage capacitor that can retain a dangerous electrical charge even after the unit is unplugged — avoid touching internal components near the capacitor and magnetron. Door interlock switches are a critical safety system: they exist specifically to cut power the instant the door opens, preventing microwave radiation from escaping the cavity. Never operate a microwave with an interlock switch disconnected, bypassed, or jumpered, even temporarily — doing so can expose you and others to microwave radiation. If you are not fully comfortable working inside a microwave's internal compartment, have a qualified appliance technician perform this repair instead. ⚠️ Photograph Wiring Before Disconnecting — Match The Failed Switch Exactly Wear work gloves. Remove the outer cabinet or access panel per your model's service instructions to reach the door switch assembly, typically located near the door latch mechanism. Photograph the wiring on the old switch before disconnecting anything, and confirm you're replacing the correct switch position if your microwave uses multiple interlock switches. Disconnect the wire terminals from the old switch, remove its mounting screws, and pull it free. Install the new EXP480 in the same position, reconnect each wire terminal to its original position, and secure the mounting screws. Reinstall the cabinet or access panel. Restore power and test that the microwave starts normally with the door closed, and — this is the critical safety check — confirm the unit stops heating immediately when the door is opened during a test run with a cup of water. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My microwave stopped working. How do I know if it's actually a door switch and not something else? A common pattern is a microwave where the display and buttons respond normally, but pressing start does nothing, or the unit hums without heating — this points toward the door interlock circuit rather than the control board. Since these switches also serve a critical safety function, if you suspect a fault in this area, it's best to have it properly diagnosed and replaced rather than working around the symptom. Is it safe to just disconnect a faulty interlock switch so the microwave will run? No — this is not safe under any circumstances. Door interlock switches exist specifically to cut power to the magnetron the instant the door opens, preventing microwave radiation from escaping. Bypassing, disconnecting, or jumpering one of these switches removes that protection and can expose you and anyone nearby to microwave radiation, even if the microwave otherwise appears to run normally. Always replace a faulty switch with a correctly rated new one rather than working around it. My microwave trips the breaker whenever I open the door. What does that mean? This can indicate that one of the door switches — often the one that should open when the door opens — has fused or welded its contacts shut from repeated electrical stress, so it continues carrying current when it shouldn't. This is a genuine safety concern and the affected switch should be replaced promptly rather than continuing to use the microwave. My microwave uses more than one door switch. How do I know which one to replace? Most microwaves use two or three separate interlock switches working together, and they don't always share the same contact configuration. Check your appliance's parts diagram or the physical switch you're replacing to confirm it matches this NC/NO combination design before ordering, and always test or verify function with a multimeter if you're uncertain which specific switch has failed. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

ES16100 Dishwasher Door Switch Replaces Part Numbers: WD21X10261, 1263984, AH1481922, AP3994765, EA1481922, 16100, ES16100, PS1481922, WD21X0557, WD21X557 Description: The Interlock Switch is a replacement part for specific GE, Hotpoint electric and gas dryer and dishwasher models. This safety component monitors the door closure, preventing operation if the door is not securely closed and latched. The switch measures 2 inches long and 1/2 inch wide. This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

Genuine Refrigerator Installation Part WX08X10015 Refrigerator Genuine SmartConnect Water Supply Line (15 Feet) Genuine 15-foot SmartConnect water supply line for compatible refrigerators and icemaker connections. Product Overview The WX08X10015 Refrigerator SmartConnect Water Supply Line is a genuine 15-foot refrigerator water line designed for compatible refrigerator and icemaker installations. It connects the household water supply to the refrigerator water inlet system. Use this line for a new installation or to replace a leaking, kinked, damaged, or deteriorated refrigerator water supply line. Quick Answer WX08X10015 is a genuine 15-foot refrigerator SmartConnect water supply line for compatible refrigerator and icemaker installations. Common Problems This Part May Fix Leaking refrigerator water supply line Kinked or restricted water tubing Damaged or deteriorated supply line Insufficient line length for refrigerator placement Water line replacement during refrigerator installation Replaces and Cross-References WX08X10015, 880515, AGE1244675, AP3140389, EAP311504, PD00065821, PS311504, TJ915PEX, IMKR15 Part number is provided for identification. This listing is for a genuine replacement and installation part. Compatibility Designed for compatible refrigerators and icemaker installations requiring SmartConnect water supply line part number WX08X10015. Important: Verify the refrigerator installation requirements, connection type, available space, and required line length before ordering. Key Features Genuine replacement and installation part 15-foot refrigerator water supply line Designed for compatible refrigerator and icemaker hookups Provides additional installation length for flexible placement Direct replacement for applications calling for WX08X10015 Product Specifications Part Number WX08X10015 Part Type Refrigerator Water Supply Line Product Line SmartConnect Length 15 Feet Application Compatible Refrigerators / Icemakers Condition New Part Quality Genuine Replacement Part Package Quantity 1 Water Supply Line Installation & Troubleshooting Notes Shut off the household water supply before installation. Disconnect refrigerator power if access to electrical components is required. Inspect the existing connection points for corrosion, damage, or leaks. Route the new supply line without sharp bends, pinching, or kinks. Secure the line to the household supply and refrigerator inlet according to the appliance installation instructions. Restore the water supply slowly and inspect all connections carefully for leaks. Installation tip: Leave enough slack behind the refrigerator so the appliance can be moved for service without pulling or stressing the water line. Frequently Asked Questions How long is WX08X10015? This SmartConnect water supply line is 15 feet long. What is WX08X10015 used for? It connects a compatible refrigerator or icemaker water inlet system to the household water supply. Is WX08X10015 a genuine part? Yes. This listing is for a genuine refrigerator water supply line. Will this work with every refrigerator? No. Verify the refrigerator installation requirements and connection specifications before ordering. Shop With Confidence Verify your refrigerator installation requirements before purchasing. Our compatibility team can help confirm whether WX08X10015 is suitable for your application. Genuine Replacement15-Foot Water LineInstallation SupportFast U.S. Shipping

Read more less

XPARTCO EBF49827801 Washer Door Lock 120V, 60Hz, lid lock and switch assembly. Fits select LG front load washers with front control panel. Replaces Part Numbers: EBF49827801, 6601ER1004C, 1268254, 1463541, 6601ER1004B, 6601ER1004E, 6601ER1004G, EBF49827802, AP4998848, PS3533609. Description: This Washer Door Lock Switch is a replacement part for select Kenmore, LG washing machine models. This critical safety feature locks the washer door during operation to prevent it from being opened, which ensures safety and proper functioning. The door lock switch also communicates with the washer's control system to indicate that the door is securely closed and the machine can begin its cycle. This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

(4 Pack) XPARTCO 6600JB3001E Refrigerator Dispenser Switch - Compatible with LG, Kenmore, GE Product Description Restore your refrigerator’s dispenser functionality with the XPARTCO 6600JB3001E Refrigerator Dispenser Switch. This high-quality replacement switch is designed for select LG, Kenmore, GE, and Hotpoint refrigerators, controlling the dispensing of ice or water when the lever is pressed. It ensures reliable operation at a cost-effective price, addressing issues like no dispensing or intermittent dispensing. Note: Includes one micro switch (16A 1/2HP, 125/250VAC, 10T150 μ1E4 ). Disconnect power before installation. Verify compatibility with your refrigerator model. Replaces part numbers: 6600JB3001E, 1268245, AH3529277, SZM-V16-2FA-53, EA3529277, AP4650818, PS3529277. Compatibility: Compatible with models including but not limited to: LG: LSC24971ST/00, LRSC21934SW Kenmore: 79571039010, 79571039011, 79578789801 GE, Hotpoint: (select models with WR23X10783 compatibility, verify part number) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select LG, Kenmore, GE, and Hotpoint refrigerators with front panel dispensers. 🔧 Specifications: Micro switch, 16A 1/2HP, 125/250VAC, T130 5E4μ, 1/4" terminals. 💪 Reliable Performance: Ensures precise activation of ice and water dispensing. 🛠️ Easy Installation: Requires screwdriver and pliers; typically installed in 15–30 minutes. 🛡️ Effective Fixes: Resolves no dispensing or intermittent dispensing issues. Product Specification Part Number: XPARTCO 6600JB3001E Component Type: Refrigerator dispenser micro switch Material: Plastic housing, metal contacts Electrical Rating: 16A 1/2HP, 125/250VAC Mounting: Snap-in or screw-mounted, 1/4" terminals Operating Conditions: Suitable for refrigerator dispenser environments Compliance: UL listed, Prop 65 warning for California. Installation Notes: Safety First: Disconnect the refrigerator from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your refrigerator dispensing smoothly today! Add to cart now for a reliable fix!

Read more less